TSOP48..SJ1
Vishay Semiconductors
1 (7)
www.vishay.comDocument Number 82118
Rev . 4, 03–May–02
Photo Modules for PCM Remote Control Systems
Available Types For Different Carrier Frequencies
Type fo Type fo
TSOP4830SJ1 30 kHz TSOP4833SJ1 33.0 kHz
TSOP4836SJ1 36 kHz TSOP4837SJ1 36.7 kHz
TSOP4838SJ1 38 kHz TSOP4840SJ1 40.0 kHz
TSOP4856SJ1 56 kHz
Description
The TSOP48..SJ1 – series are miniaturized receivers
for infrared remote control systems. PIN diode and
preamplifier are assembled on lead frame, the epoxy
package is designed as IR filter.
The demodulated output signal can directly be
decoded by a microprocessor. TSOP48..SJ1 is the
standard IR remote control receiver series, supporting
all major transmission codes. 16656
Features
Photo detector and preamplifier in one package
Internal filter for PCM frequency
Improved shielding against electrical field
disturbance
TTL and CMOS compatibility
Output active low
Special Features
Low power consumption
High immunity against ambient light
Continuous data transmission possible (800 bit/s)
Suitable burst length 10 cycles/burst
Block Diagramm
9612226
PIN
Input
AGC
Control
Circuit
Band
Pass Demodu-
lator
30 k
2
3
1
VS
OUT
GND
TSOP48..SJ1
Vishay Semiconductors
www.vishay.com
2 (7) Rev . 4, 03–May–02
Document Number 82118
Absolute Maximum Ratings
Tamb = 25°C Parameter Test Conditions Symbol Value Unit
Supply Voltage (Pin 3) VS–0.3...6.0 V
Supply Current (Pin 3) IS5 mA
Output Voltage (Pin 1) VO–0.3...6.0 V
Output Current (Pin 1) IO5 mA
Junction Temperature Tj100 °C
Storage Temperature Range Tstg –25...+85 °C
Operating Temperature Range Tamb –25...+85 °C
Power Consumption (Tamb 85 °C) Ptot 50 mW
Soldering Temperature t 10 s, 1 mm from case Tsd 260 °C
Basic Characteristics
Tamb = 25°C
Parameter Test Conditions Symbol Min. Typ. Max. Unit
Supply Current (Pin 3) VS = 5 V, Ev = 0 ISD 0.8 1.1 1.5 mA
y()
VS = 5 V, Ev = 40 klx, sunlight ISH 1.4 mA
Transmission Distance Ev = 0, test signal see fig.7,
IR diode TSAL6200, IF = 250 mA d 35 m
Supply Voltage VS4.5 5.5 V
Output Voltage Low (Pin 1) IOSL = 0.5 mA,Ee = 0.7 mW/m2VOSL 250 mV
Irradiance (56 kHz) Pulse width tolerance:
ti5/f <t <ti+ 6/f
Ee min 0.3 0.6 mW/m2
Irradiance (30–40 kHz) tpi – 5
/f
o < tpo < tpi + 6
/f
o,
test signal see fig.7 Ee min 0.2 0.4 mW/m2
Irradiance tpi – 5/fo < tpo < tpi + 6/foEe max 30 W/m2
Directivity Angle of half transmission distance ϕ1/2 ±45 deg
Application Circuit
16247
TSAL62..
4.7 F *)
C
>10 k
optional
100 *)
*) recommended to suppress power supply disturbances
**) the output voltage should not be hold continuously at a voltage below 3.3V by the external circuit.
GND
TSOP48..SJ1
**)
3
1
2
+5V
TSOP48..SJ1
Vishay Semiconductors
3 (7)
www.vishay.comDocument Number 82118
Rev . 4, 03–May–02
Suitable Data Format
The circuit of the TSOP48..SJ1 is designed in that way
that unexpected output pulses due to noise or
disturbance signals are avoided. A bandpassfilter, an
integrator stage and an automatic gain control are
used to suppress such disturbances.
The distinguishing mark between data signal and
disturbance signal are carrier frequency, burst length
and duty cycle.
The data signal should fullfill the following condition:
Carrier frequency should be close to 38 kHz.
Burst length should be 10 cycles/burst or longer.
After each burst which is between 10 cycles and
70 cycles a gap time of at least 14 cycles is
neccessary.
For each burst which is longer than 1.8 ms a
corresponding gap time is necessary at some
time in the data stream. This gap time should be
at least 4 times longer than the burst.
Up to 800 short bursts per second can be
received continuously.
Some examples for suitable data format are:
NEC Code, Toshiba Micom Format, Sharp Code,
RC5 Code, R–2000 Code.
When a disturbance signal is applied to the
TSOP48..SJ1 it can still receive the data signal.
However the sensitivity is reduced to that level that no
unexpected pulses will occure.
Some examples for such disturbance signals which
are suppressed by the TSOP48..SJ1 are:
DC light (e.g. from tungsten bulb or sunlight)
Continuous signal at 38 kHz or at any other
frequency
Signals from fluorescent lamps with electronic
ballast with low modulation
(see Figure A or Figure B).
0 5 10 15 20
time [ms]
Figure A: IR Signal from Fluorescent Lamp with low Modulation
0 5 10 15 20
time [ s ]
Figure B: IR Signal from Fluorescent Lamp with high Modulation
TSOP48..SJ1
Vishay Semiconductors
www.vishay.com
4 (7) Rev . 4, 03–May–02
Document Number 82118
Typical Characteristics (Tamb = 25C, unless otherwise specified)
0.7 0.8 0.9 1.0 1.1
E / E – Rel. Responsitivity
e min
f/f0 – Relative Frequency
1.3
94 8143
0.0
0.2
0.4
0.6
0.8
1.0
e
1.2
f = f05%
f ( 3dB ) = f0/10
Figure 1. Frequency Dependence of Responsivity
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0.1 1.0 10.0 100.0 1000.0 10000.0
Ee – Irradiance ( mW/m2 )96 12110
po
t – Output Pulse Length (ms)
Input burst duration
= 950 nm,
optical test signal, fig.7
Figure 2. Sensitivity in Dark Ambient
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0.01 0.10 1.00 10.00 100.00
E – DC Irradiance (W/m2)96 12111
e min
E – Threshold Irradiance (mW/m )
2
Correlation with ambient light sources
(Disturbanceeffect):10W/m21.4klx
(Stand.illum.A,T=2855K)8.2klx
(Daylight,T=5900K)
Ambient, = 950 nm
Figure 3. Sensitivity in Bright Ambient
0.0 0.4 0.8 1.2 1.6
0.0
0.4
0.8
1.2
2.0
E – Field Strength of Disturbance ( kV/m )
2.0
94 8147
1.6
E – Threshold Irradiance ( mW/m )
e min 2
f(E)=f0
Figure 4. Sensitivity vs. Electric Field Disturbances
0.01 0.1 1 10 100
0.1
1
10
1000
94 9106 VsRMS AC Voltage on DC Supply Voltage (mV)
E – Threshold Irradiance ( mW/m )
e min 2
f = f0
10 kHz
100 Hz
1 kHz
Figure 5. Sensitivity vs. Supply Voltage Disturbances
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
30150 153045607590
Tamb – Ambient Temperature ( °C )96 12112
e min
E – Threshold Irradiance (mW/m )
2
Sensitivity in dark ambient
Figure 6. Sensitivity vs. Ambient Temperature
TSOP48..SJ1
Vishay Semiconductors
5 (7)
www.vishay.comDocument Number 82118
Rev . 4, 03–May–02
Ee
T
tpi *
t
* tpi 10/fo is recommended for optimal function
VO
VOH
VOL t
16110
Optical Test Signal
(IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, T = 10 ms)
Output Signal
td1 )tpo2 )
1 ) 7/f0 < td < 15/f0
2 ) tpo = tpi 6/f0
Figure 7. Output Function
Ee
t
VO
VOH
VOL t
600 s 600 s
T = 60 ms
Ton Toff
94 8134
Optical Test Signal
Output Signal, ( see Fig.10 )
Figure 8. Output Function
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
10 20 30 40 50 60 70 80 90
Burstlength [number of cycles/burst]16156
Envelope Duty Cycle
f = 38 kHz
Figure 9. Max. Envelope Duty Cycle vs. Burstlength
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0.1 1.0 10.0 100.0 1000.0 10000.0
Ee – Irradiance (mW/m2)96 12114
on off
T ,T – Output Pulse Length (ms)
Ton
= 950 nm,
optical test signal, fig.8
Toff
Figure 10. Output Pulse Diagram
750 850 950 1050
0
0.2
0.4
0.6
0.8
1.2
S ( ) – Relative Spectral Sensitivity
rel
– Wavelength ( nm )
1150
94 8408
1.0
Figure 11. Relative Spectral Sensitivity vs. Wavelength
96 12223p2
0.4 0.2 0 0.2 0.4 0.6
0.6
0.9
0°30°
10°20°
40°
50°
60°
70°
80°
1.0
0.8
0.7
drel – Relative Transmission Distance
Figure 12. Directivity
TSOP48..SJ1
Vishay Semiconductors
www.vishay.com
6 (7) Rev . 4, 03–May–02
Document Number 82118
Dimensions in mm
16705
TSOP48..SJ1
Vishay Semiconductors
7 (7)
www.vishay.comDocument Number 82118
Rev . 4, 03–May–02
Ozone Depleting Substances Policy Statement
It is the policy of Vishay Semiconductor GmbH to
1. Meet all present and future national and international statutory requirements.
2. Regularly and continuously improve the performance of our products, processes, distribution and operating
systems with respect to their impact on the health and safety of our employees and the public, as well as
their impact on the environment.
It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone
depleting substances (ODSs).
The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their
use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances.
Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs
listed in the following documents.
1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively
2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental
Protection Agency (EPA) in the USA
3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively.
Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances
and do not contain such substances.
We reserve the right to make changes to improve technical design and may do so without further notice.
Parameters can vary in different applications. All operating parameters must be validated for each customer application
by the customer. Should the buyer use Vishay Telefunken products for any unintended or unauthorized application, the
buyer shall indemnify Vishay Telefunken against all claims, costs, damages, and expenses, arising out of, directly or
indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use.
Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany
Telephone: 49 (0)7131 67 2831, Fax number: 49 (0)7131 67 2423