SL74HCT163 Presettable Counters High-Performance Silicon-Gate CMOS The SL74HCT163 is identical in pinout to the LS/ALS163. The SL74HCT163 may be used as a level converter for interfacing TTL or NMOS outputs to High Speed CMOS inputs. The SL74HCT163 is programmable 4-bit synchronous counter that feature parallel Load, synchronous Reset, a Carry Output for cascading and count-enable controls. The SL74HCT163 is binary counter with synchronous Reset. * TTL/NMOS Compatible Input Levels * Outputs Directly Interface to CMOS, NMOS, and TTL * Operating Voltage Range: 4.5 to 5.5 V * Low Input Current: 1.0 A ORDERING INFORMATION SL74HCT163N Plastic SL74HCT163D SOIC TA = -55 to 125 C for all packages LOGIC DIAGRAM PIN ASSIGNMENT PIN 16 =VCC PIN 8 = GND FUNCTION TABLE Inputs Outputs Reset Load Enable P Enable T L X X H L H Clock Q0 Q1 Q2 Q3 Function X L L L L Reset to "0" X X P0 P1 P2 P3 Preset Data H X L No change No count H H L X No change No count H H H H Count up Count X X X X No change No count X=don't care P0,P1,P2,P3 = logic level of Data inputs Ripple Carry Out = Enable T * Q0 * Q1 * Q2 * Q3 SLS System Logic Semiconductor SL74HCT163 MAXIMUM RATINGS * Symbol Parameter Value Unit -0.5 to +7.0 V VCC DC Supply Voltage (Referenced to GND) VIN DC Input Voltage (Referenced to GND) -1.5 to VCC +1.5 V DC Output Voltage (Referenced to GND) -0.5 to VCC +0.5 V DC Input Current, per Pin 20 mA DC Output Current, per Pin 25 mA ICC DC Supply Current, VCC and GND Pins 50 mA PD Power Dissipation in Still Air, Plastic DIP+ SOIC Package+ 750 500 mW -65 to +150 C 260 C VOUT IIN IOUT Tstg TL Storage Temperature Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/C from 65 to 125C SOIC Package: : - 7 mW/C from 65 to 125C RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN, VOUT Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage, Output Voltage (Referenced to GND) TA Operating Temperature, All Package Types tr, t f Input Rise and Fall Time (Figure 1) Min Max Unit 4.5 5.5 V 0 VCC V -55 +125 C 0 500 ns This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND(VIN or VOUT)VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. SLS System Logic Semiconductor SL74HCT163 DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) VCC Guaranteed Limit Test Conditions V 25 C to -55C 85 C 125 C Unit Minimum High-Level Input Voltage VOUT=0.1 V or VCC-0.1 V IOUT 20 A 4.5 5.5 2.0 2.0 2.0 2.0 2.0 2.0 V VIL Maximum Low -Level Input Voltage VOUT=0.1 V or VCC-0.1 V IOUT 20 A 4.5 5.5 0.8 0.8 0.8 0.8 0.8 0.8 V VOH Minimum High-Level Output Voltage VIN=VIH or VIL IOUT 20 A 4.5 5.5 4.4 5.4 4.4 5.4 4.4 5.4 V VIN=VIH or VIL IOUT 6.0 mA 4.5 3.98 3.84 3.7 VIN=VIH or VIL IOUT 20 A 4.5 5.5 0.1 0.1 0.1 0.1 0.1 0.1 VIN=VIH or VIL IOUT 6.0 mA 4.5 0.26 0.33 0.4 Symbol Parameter VIH VOL Maximum Low-Level Output Voltage V IIN Maximum Input Leakage Current VIN=VCC or GND 5.5 0.1 1.0 1.0 A ICC Maximum Quiescent Supply Current (per Package) VIN=VCC or GND IOUT=0A 5.5 4.0 40 160 A ICC Additional Quiescent Supply Current VIN = 2.4 V, Any One Input VIN=VCC or GND, Other Inputs -55C 25C to 125C mA 2.9 2.4 IOUT=0A SLS System Logic Semiconductor 5.5 SL74HCT163 AC ELECTRICAL CHARACTERISTICS (VCC=5.0 V 10%, CL=50pF,Input t r=t f=6.0 ns) Guaranteed Limit Symbol Parameter 25 C to -55C 85C 125C Unit fmax Maximum Clock Frequency (Figures 1,6) 30 24 20 MHz tPLH Maximum Propagation Delay, Clock to Q 34 43 51 ns tPHL (Figures 1,6) 41 51 62 ns tPLH Maximum Propagation Delay, Enable T to Ripple Carry Out (Figures 2,6) 32 40 48 ns 39 49 59 ns tPHL tPLH Maximum Propagation Delay, Clock to Ripple 35 44 53 ns tPHL Carry Out (Figures 1,6) 43 54 65 ns Maximum Output Transition Time, Any Output, (Figures 1 and 6) 15 19 22 ns Maximum Input Capacitance 10 10 10 pF tTLH, t THL CIN Power Dissipation Capacitance (Per Gate) CPD Typical @25C,VCC=5.0 V Used to determine the no-load dynamic power consumption: PD=CPDVCC2f+ICCVCC+ICCVCC 60 pF TIMING REQUIREMENTS (VCC=5.0 V 10%, CL=50pF,Input t r=t f=6.0 ns) Guaranteed Limit Symbol Parameter 25 C to -55C 85C 125C Unit tsu Minimum Setup Time, Preset Data Inputs to Clock (Figure 4) 30 38 45 ns tsu Minimum Setup Time, Load to Clock (Figure 4) 27 34 41 ns tsu Minimum Setup Time, Reset to Clock (Figure 3) 32 40 48 ns tsu Minimum Setup Time, Enable T or Enable P to Clock (Figure 5) 40 50 60 ns th Minimum Hold Time, Clock to Preset Data Inputs (Figure 4) 10 13 15 ns th Minimum Hold Time, Clock to Load (Figure 4) 3 3 3 ns th Minimum Hold Time, Clock to Reset (Figure 3) 3 3 3 ns th Minimum Hold Time, Clock to Enable T or Enable P (Figure 5) 3 3 3 ns trec Minimum Recovery Time, Load Inactive to Clock (Figure 4) 25 31 38 ns tw Minimum Pulse Width, Clock (Figure 1) 16 20 24 ns tw Minimum Pulse Width, Reset (Figure 4) 16 20 24 ns Maximum Input Rise and Fall Times (Figure 1) 500 500 500 ns tr, tf SLS System Logic Semiconductor SL74HCT163 SLS System Logic Semiconductor SL74HCT163 Figure 1. Switching Waveforms Figure 2. Switching Waveforms Figure 3. Switching Waveforms Figure 4. Switching Waveforms Figure 5. Switching Waveforms Figure 6. Test Circuit SLS System Logic Semiconductor SL74HCT163 VCC=Pin 16 GND=Pin 8 The flip-flops shown in the circuit diagrams are Toggle-Enable flip-flops. A Toggle-Enable flip-flop is a combination of a D flip-flop and a T flip-flop. When loading data from Preset inputs P0, P1, P2, and P3, the Load signal is used to disable the Toggle input (Tn) of the flip-flop. The logic level at the Pn input is then clocked to the Q output of the flip-flop on the next rising edge of the clock. A logic zero on the Reset device input forces the internal clock (C) high and resets the Q output of the flipflop low. Figure 7.Expanded logic diagram SLS System Logic Semiconductor SL74HCT163 Sequence illustrated in waveforms: 1. Reset outputs to zero. 2. Preset to binary twelve. 3. Count to thirteen, fourteen, fifteen, zero, one, and two. 4. Inhibit. Figure 8. Timing Diagram SLS System Logic Semiconductor SL74HCT163 TYPICAL APPLICATIONS CASCADING Note:When used in these cascaded configurations the clock fmax guaranteed limits may not apply. Actual performance will depend on number of stages. This limitation is due to set up times between Enable (Port) and clock. Figure 9. N-Bit Synchronous Counters Figure 10. Nibble Ripple Counter SLS System Logic Semiconductor