WALL BOX SOLUTIONS Indoor/Outdoor Fiber Terminals, Cabinets and Boxes for FTTx BROADBAND NETWORK SOLUTIONS /// WALL BOX SOLUTIONS Contents Introduction.................................................................................................................................................................4 Products-at-a-Glance............................................................................................................................................5 Mini Rapid Fiber Distribution Terminal (RDT)...........................................................................................8 Rapid Fiber Distribution Terminal (RDT)..................................................................................................10 Small Outdoor Fiber Distribution Terminal (oFDT)............................................................................11 Large Outdoor Fiber Distribution Terminal (oFDT)............................................................................13 Indoor Fiber Distribution Terminals (iFDT).............................................................................................15 Indoor Fiber Wall Mount Boxes.....................................................................................................................17 FL1 6pak Adapter Packs...................................................................................................................................19 Flexible Fiber Box (FFB)...................................................................................................................................22 Fiber Splitter Box (FSB)....................................................................................................................................25 Premises Patch and/or Splice Enclosure - FibrBoss PB 06-S.......................................................28 Premises Patch and/or Splice Enclosure - FibrBoss PB 06-B......................................................29 Wall Outlets - OWB-S (Outdoor Wall Mounted Small Box)...........................................................30 Rapid Fiber Faceplate........................................................................................................................................31 Wall Outlets - Customer Wall Outlet (COWO)......................................................................................32 Wall Outlets - Transition Box with DLX Adapters...............................................................................33 Wall Outlets - FTUO (Fiber Termination Unit Outdoor)..................................................................34 Wall Outlets - Customer Premises Wall Outlet (HFTP)....................................................................35 Accessories...............................................................................................................................................................36 Wall Box Solutions Introduction TE Connectivity (TE): The Connectivity Leader in Fiber Wall Box Solutions PERFORMANCE No matter what your network requirements are, TE has a complete portfolio of wall box solutions available to meet your fiber connectivity needs. In today's competitive marketplace, every subscriber counts, which demands service providers to be more strategic in their network plans and fiber deployments. To satisfy customers' bandwidth requirements, service providers need to build their networks smarter, faster and more efficiently. At the same time, increased competition in the marketplace is pressuring providers to reduce unnecessary capital and operating expenses wherever possible. These challenges can have a major impact on service providers' bottom line. Ultimately, choosing network equipment that addresses flexibility and future capacity is vital to building and sustaining a costeffective and profitable network. TE's wall box solutions help to address these challenges, and offer customers' unrivaled quality, performance and reliability for the multifaceted needs of tomorrow's networks. TE's wall box solutions are designed to perform in the most rigorous customer applications and in a variety of fiber environments. * Created for longevity and low life-cycle cost * Ensure fast and easy installation * Engineered for easy expansion and for cost-effective upgrades * Withstands harsh inside and outside environmental conditions INNOVATION Many TE wall box solutions incorporate the latest in cuttingedge technology, helping to deliver unmatched savings in installation time, labor costs and performance in all fiber networks. * RapidReel fiber cable spool allows the cable to payoff directly from the enclosure assembly--speeds installation and reduces labor requirements * Reduced bend radius fiber eliminates attenuation caused from macro bends; and allows for tighter slack storage spools and promotes the use of smaller enclosure TE WALL BOX PORTFOLIO TE wall boxes are designed for use in both in-building and outside plant environments--from the CO/Head End to the customer premises locations. * Low-loss MPO connectors promote the use of easier handing and routing of cables * Offer an unrivaled breadth of low to high density solutions with superior cable management * Unique swing-frame design allows easy technician access to connectors and fibers for MACS * "Right sized" enclosures meet space requirements for a variety of environments * Plug-and-play technology reduces splice labor requirements and speeds service turn ups * Proven reliability in fiber networks QUALITY * Modular, "build as you grow" flexibility TE strives to exceed customer expectations and is committed to delivering the highest quality products throughout the world. TE accomplishes this through continual improvement in customer satisfaction, supplier relationships and our business management system. ISO 9001 standards and statistical process controls help to keep TE's wall box equipment within strict specifications--serving the life of the product. * Promotes fast service turn ups CABLE MANAGEMENT The management of the fiber cables has a direct impact on network reliability, performance and cost. TE's wall box solutions incorporate the four elements of a successful cable management system: * Integrated bend radius protection * Clear, intuitive cable routing paths * Easy connector and cable access * Physical protection of fiber 4 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Products-at-a-Glance TE Solutions for Fiber Connectivity Specifications Application Mini Rapid Fiber Distribution Installation Type Indoor * Basements Terminal (RDT) Size (HxWxD) 7.9"x5.5"x2.4" * Premises Locations See page 9 Fibers 12 * Campuses Splice Capabilities No * In-building RapidReel * FTTH Deployments Yes * Wireless Backhaul * MSO Rapid Fiber Distribution Installation Type Indoor * Basements Terminal (RDT) Size (HxWxD) 6"x9"x4" * Premises Locations See page 11 Fibers 12-24 * Campuses Splice Capabilities Yes * In-building RapidReel * FTTH Deployments Yes * Wireless Backhaul Small Outdoor Fiber Installation Type Outdoor * Interconnect Distribution Terminal Size (HxWxD) 13.5"x19"x8.25" * Entrance Rooms See page 13 Fibers 48 * Basements Splice Capabilities Yes * Premises Locations RapidReel * LANs No * Campuses * In-building * FTTH Deployments * Wireless Backhaul * Base Station * Security * MSO * OSP * Metro Fiber Ring Large Outdoor Fiber Installation Type Outdoor * Cross-connect Distribution Terminal Size (HxWxD) 22"x20"x10" * Interconnect See page 15 Fibers 96 * Entrance rooms Splice Capabilities Yes * Basements RapidReel * Premises No * Locations * LANs * Campuses * In-building * FTTH Deployments * Wireless Backhaul * Base Station * Security * MSO * OSP * Metro Fiber Ring *Outdoor rated splice boxes only 5 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Products-at-a-Glance TE Solutions for Fiber Connectivity Specifications Application Fiber Distribution Terminals Installation Type Indoor * Campuses (iFDT) Size (HxWxD) Varies * In-building See pages 17 Fibers 12-96 * FTTH Deployments Splice Capabilities Yes * Wireless RapidReel No * Backhaul FL1 Wall Boxes Installation Type Indoor * Interconnect See page 19 Size (HxWxD) Varies * Central Office Fibers 12-72 * Entrance Rooms Splice Capabilities Yes * Communications Rooms RapidReel * Indoor No FL1 6pack Adapter Packs, Splice * FL1 Wall Box Applications Trays, Hardware See pages 21 Flexible Fiber Box (FFB) Installation Type Indoor/Outdoor * Indoor/outdoor See pages 24 Size (HxWxD) 10.5"x12"x5" * Basements Fibers 24 * Premis Locations Splice Capabilities Yes * Wireless Backhaul RapidReel Yes * FTTA/FTTH/FTTCS Fiber Splitter Box (FSB) Installation Type Varies * FTTH Deployments See pages 27 Size (HxWxD) Varies * Wireless Backhaul Fibers 16-72 * MSO Splice Capabilities Yes RapidReel * Indoor/outdoor No FibrBoss PB06-S Installation Type Indoor/Outdoor * Indoor/outdoor See pages 36 Size (HxWxD) 5"x4"x2" * FTTH/FTTB Fibers 6 * Interconnect Splice Capabilities Yes RapidReel No FibrBoss PB06-B Installation Type Indoor/Outdoor * Indoor/outdoor See pages 37 Size (HxWxD) 4.8"x6.4"x2.4" * FTTH/FTTB Fibers 6 * Interconnect Splice Capabilities Yes RapidReel 6 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 No 12/14 109756.2AE Wall Box Solutions Products-at-a-Glance TE Solutions for Fiber Connectivity Specifications Application Outdoor Wall Mounted Small Installation Type Box (OWB-S) Size (HxWxD) See pages 38 209.8mmx173.8mmx72mm Fibers Outdoor * Indoor/Outdoor * Wall/Pole Mount * FTTH 4 Splice Capabilities Yes RapidReel No Rapid Fiber Faceplate * Indoor See pages 39 * FTTH * Wall Mount Customer Wall Outlet (COWO) * Indoor See pages 40 * FTTH/FTTD OmniReach Transition Box with * Indoor DLX Adapters * Wall Mount See pages 41 * FTTH Fiber Termination Unit (FTUO) * Indoor See pages 42 * FTTH * Wall Mount Customer Premises Wall Outlet * Indoor (HFTP) * FTTH/FTTD See pages 43 7 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Mini Rapid Fiber Distribution Terminal (RDT) The mini Rapid Fiber distribution terminal (RDT) is compact, high-density, fiber box solution, designed to speed installation requirements on the customer premises. Utilizing the RapidReel fiber cable spool, the mini RDT deploys up to 650' (198 m) of 12-fiber 3 mm cable. The multifiber cable terminates to a multifiber push-on connector (MPO), which ensures fast cable routing and handling by technicians. For service turn-up, the mini RDT features 12- SC/APC adapter ports for fast, plug-and-play drop cable connections. The mini RDT is a cost-efficient system for deploying and managing fiber networks within small to mid-sized multiple dwelling unit (MDU) and multiple tenant unit (MTU) environments. FEATURES * Compact design: 7.9 x 5.5 x 2.4 in (200 x 140 x 60 mm) * RapidReel fiber cable spool deploys up to 100' (30 m) of stubbed cable * 12-fiber 3 mm cable is factory terminated with a low-loss MPO connector * Equipped with 4, 8 or 12 SC/APC adapter ports * Plastic construction - no grounding required * Removable cover and adapter housing * Screw mounts to a wall or flat surface * Security screw holds cover in place * Flexible cable routing: Distribution cable can exit from bottom or side of unit BENEFITS * Cost Savings: RapidReel cable spool reduces upfront deployment costs by eliminating site survey inspections, reducing labor hours and streamlining cable requirements * Reduced Labor: Preconnectorized plug-and-play solution eliminates splice labor requirements and speeds network construction * Easy Access: Technician friendly, the mini RDT provides easy access to connectors for service and maintenance * Space Savings: Compact MPO connector design and multi-fiber cable is ideal for high density intrafacility applications. Excess fiber is stored within unit, no additional enclosures are required SPECIFICATIONS Installation Type: Fibers: Splice Trays: Cable Ports: Rating: Height: Width: Depth: 8 www.te.com/bns Indoor 12 N/A 1 Bottom UL 7.9" (200mm) 5.5" (140 mm) 2.4" (60mm) 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Mini Rapid Fiber Distribution Terminal (RDT) Catalog Number RDT - S M __ __ __ 0 0 __ __ __ __ __ __ Enclosure Type M Stubbed End Configuration 12 Fiber plastic Cable Count 04 4 08 8 12 12 SC/APC K LC/UPC L LC/APC N SC/UPC A MPO connector J SC/APC O No connector K LC/UPC L LC/APC N SC/UPC Enclosure End Configuration 9 Connector Type J Fanout 900 m - standard Cable Length (Plenum)1 Cable Type Cable Length (Indoor/Outdoor)1 030 30 meters (100') 015 061 61 meters (200') 030 30 meters (100') 092 92 meters (300') 045 45 meters (150') 122 122 meters (400') 15 meters (50') 061 61 meters (200') D Indoor/outdoor 3.6mm black 152 152 meters (500') 076 76 meters (250') P 3 mm loose tube ivory plenum (zipcord for 24 fibers) 183 183 meters (600') 092 92 meters (300') 107 107 meters (350') 122 122 meters (400') 137 137 meters (450') 152 152 meters (500') 168 168 meters (550') 183 183 meters (600') 198 198 meters (650') External spool included for plenum cable lengths over 650' (198 m) and indoor/ outdoor cable over 600' (183 m) 1 9 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Rapid Fiber Distribution Terminal (RDT) Eliminates the need for splice cases and separate cable assemblies by integrating the patened RapidReel fiber cable spool. The RapidReel cable spool includes a built-in reel enabling quick payoff of up to 500 feet of MPO stubbed 12 or 24 count optical fiber cable from a single 6"x 9" wall box. The MPO stub is pulled for installation into either the collector enclosure or directly to an indoor or outdoor fiber distribution hub, panel, connector or adapter with MPO compatibility. After installation the spool flanges can be broken away and the wall box is secured to the wall safely storing the remaining slack cable. Use of factory terminated and tested MPO connectors instead of splicing provide a plug-and-play environment that reduces labor costs and speeds project completion. Rapid Fiber RDT using slider adapter packs FEATURES AND BENEFITS * Built-in spool allows for easy payoff of MPO stub * RapidReel cable spool allows the cable to payoff from the complete stubbed enclosure assembly * Break-away spool flanges reduce slack storage size to within the enclosures footprint Rapid Fiber RDT with built-in spool * Designed for indoor use * Utilizes reduced bend radius fiber * Designed to meet NEMA 12 requirements SPECIFICATIONS Installation Type Fibers Splice Trays Cable Ports Rating Height Width Depth RDT-12 Indoor 12 2/12f 2 top; 1 bottom NEMA-12 6.0" 9.0" 4.0" (5.5" with splice) RDT-24 Indoor 24 2/12f 2 top; 1 bottom NEMA-12 6.0" 9.0" 4.0" (5.5" with splice) ORDERING INFORMATION Catalog Number RDT- __ __ __ __ __ __ __ __ __ __ __ 2 __ Configuration S Stubbed End Configuration Standard Enclosure Type J Fiber Count 12 24 24 SC/APC N SC/UPC Splice Trays (only on splice boxes) 0 No tray 2 Heat shrink fusion 10 0 No connectors 2 2 mm fanouts 100 100' No connectors 200 200' 300 300' 400 400' 500 500' D 3 mm loose tube plenum (zipcord for 24 fiber) B 12 F 3 mm loose tub riser C 12F 3.6 mm loose tube indoor/outdoor Provider Side Pigtails =(only on splice boxes) www.te.com/bns 1-800-366-3891 x73000 Cable Length 0 Cable Type Connector Type J MPO connectors Enclosure End Configuration 24 fiber 12 A P 3 mm, 12 fiber fanouts with 2 mm outputs 0 No pigtails, no splice trays Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Small Outdoor Fiber Distribution Terminal (oFDT) The small outdoor fiber distribution terminal is designed to terminate, splice and interconnect up to 48 fiber optic cables in an outdoor environment. The enclosure is mounted to the exterior surface and connects the distribution cable and drops. The cables meet at a central connector field that includes termination for the distribution cable and drop cables. The cabinet may be configured with splice trays for splicing the cable to connector pigtails. The oFDT may be pre-terminated on the distribution side with outside plant cable stubs so that the unit is quickly connected. The oFDT may also be pre-wired with pigtails on the drop side so that individual drops routed into the unit can be spliced to the connectorized pigtails. The oFDT features a unique "swing frame" type design that separates the splicing in the rear from the patch access in the front of the swing frame. It allows for easy connector access to the rear connectors for maintenance and cleaning. This approach allows for a single door sealing method, ensuring reliability to withstand long-term outdoor conditions. The unit accommodates a variety of OSP cable types via sealed grommet entry. Cables are secured with standard grip clamps to provide required pull out strength. The enclosure provides grounding for metallic members and for the cabinet. The oFDT product accommodates 6, 12, 24 or 48 fibers. Distribution cable fibers are terminated on standard SC/APC, SC/UPC and LC/APC adapters that are easily accessible for service connection and maintenance. Drop pigtails are terminated on adapters adjacent to the distribution termination adapters until services are requested. FEATURES AND BENEFITS * Accommodates smaller fiber counts; 6-, 12- and 24-fiber * Eliminates need for transitional NEMA box that provides for mini-ducts * Liquid tight fittings offer cost savings * Supplied pigtails and splice tray * Wall-mount; efficient use of wall space * Cable termination and splicing * Complete connector access * Lockable 216 tool/padlock offers flexible security options * Environmental enclosure provides heavy-duty protection from wind, dust, rain, and other contaminants * Aluminum welded construction provides strength and resists corrosion * Lightweight structure provides for easy installation * Cable entrance ports seal cable at entry * Cable management and routing limits radius and adds strain relief * Standard stub lengths of 100, 300, 500, and 1000 feet 11 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Small Outdoor Fiber Distribution Terminal (oFDT) SPECIFICATIONS FDT-G Outdoor 48 2 Trays 4 Bottom NEMA-4 13.5" 19" 8.25" Installation Type: Fibers: Splice Trays: Cable Ports: Rating: Height: Width: Depth: Catalog Number FDT- __ __ __ __ __ N X __ __ __ __ 0 Enclosure G Stub Length oFDT-48 (Available with -6, -12, -24 and -48 Fibers) Connector Type 000 0 Feet (Pigtail Option) 025 25 Feet 100 100 Feet 200 200 Feet J SC/APC 300 300 Feet N SC/UPC 500 500 Feet K LC/UPC Singlemode Cable Type Multimode 9 MMSC 6 MMLC Pigtails Splice Tray A Bare Ribbon Pigtail Assembly B 12 Fiber Software Bundle* Stubs 0 No Tray S Ribbon OSP w/Conn 2 Heat Shrink Fusion R Ribbon IFC w/Conn 3 Mechanical/Ribbon T Loose Tube OSP w/Conn V Loose Tube IFC w/Conn O Adapters Only Fiber Count 06 6 Fiber 12 12 Fibers 24 24 Fibers 48 48 Fibers *900 micron fiber bundled in a soft jacket. 12 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Large Outdoor Fiber Distribution Terminal (oFDT) The TE outdoor fiber distribution terminal is designed to terminate, splice and interconnect up to 96 fiber optic cables with SC connectors, or 192 cables with LC connectors in an outdoor environment. This terminal may be adapted to applications by mounting the enclosure to the exterior surface and connecting between the distribution cable and drops. The oFDT is typically divided into two side-by-side sections with distribution cable routed into one side and drop cable routed into the other side. The cables meet at a central connector field that includes termination for the distribution cable. Each side of the cabinet may be configured with splice trays for splicing the cable to connector pigtails. The oFDT-may be pre-terminated on the distribution side with outside plant cable stubs so that the unit is quickly connected to the plant. The oFDT may be prewired with pigtails so that individual drops routed into the unit can be spliced to the connectorized pigtails. The unit accommodates a variety of OSP cable types via sealed grommet entry. Cables are secured with standard grip clamps to provide required pull out strength. The enclosure provides grounding for metallic members and for the cabinet. MOUNTING APPLICATIONS All units are configurable for a variety of mounting arrangements including wall, pole and pedestal mounting. Each unit is provided nominally with a wall mount bracket. Optional pole-mount brackets and pedestals may be ordered separately. FEATURES AND BENEFITS * Environmental enclosure provides heavy-duty protection from wind, rain, and other contaminants * Aluminum welded construction provides strength and resists corrosion * Flexible design accommodates 24, 48, 72 and 96 fibers * Lightweight structure provides for easy installation * Lockable tool or padlock offers flexible security options * Cable entrance ports seal cable at entry * Cable management and routing limits radius and adds strain relief SPECIFICATIONS Installation Type: Fibers: Splice Trays: Cable Ports: Rating: Height: Width: Depth: 13 www.te.com/bns FDT-F Outdoor 96 2 Trays 3 Bottom NEMA-4 22" 20" 10" 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Large Outdoor Fiber Distribution Terminal (oFDT) Catalog Number FDT- __ __ __ __ __ NX __ __ __ __ Enclosure F oFDT-96 (Available with -24, -48, -72 and -96 Fibers) Stub Length Connector Type 000 0 Feet 025 25 Feet J SC/APC 100 100 Feet N SC/UPC 200 200 Feet K LC/UPC 300 300 Feet 500 500 Feet Singlemode Multimode 9 MMSC 6 MMLC Cable Type Splice Tray Pigtails 0 No Tray 0 No Pigtails 2 Heat Shrink Fusion A Bare Ribbon Pigtail Assembly 3 Mechanical/Ribbon B 12 Fiber Softwall Bundle Stubs S Ribbon OSP w/Conn 24 Fibers R Ribbon IFC w/Conn 48 48 Fibers T Loose Tube OSP w/Conn 72 72 Fibers V Loose Tube IFC w/Conn 96 96 Fibers Fiber Count 24 *900 micron fiber bundled in a soft jacket. 14 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Indoor Fiber Distribution Terminals (iFDT) The TE indoor fiber distribution terminal (iFDT) series provides customer premises equipment applications with a compact and secure family of enclosures for connecting fiber cables within building entrance locations, communication closets, computer rooms and other indoor environments. The iFDT products utilize a rugged double-hinged design that effectively isolates the splicing and cable termination in the rear compartment from the jumper interconnection in the front compartment. Separating the cable splicing and termination function from the interconnection function allows the unit to be used as a dual-access product with secure lockable access provided for each compartment. The layered iFDT and staggered interconnection field provides ease of access to all connections. SIZES The iFDT products are designed to splice and terminate fibers in a range of sizes including 6, 12, 24, 48, 72, and 96 fibers. MOUNTING APPLICATIONS The TE iFDT series cabinets are for indoor wall mount applications and are designed to NEMA-12 rating. The dual hinged design allows complete front and rear access. The two secure doors are locked with a standard can wrench tool and may optionally be secured with a standard pad-lock. The unit may also be configured for single lock entry thus allowing the products to be used for single access applications. FIBER MANAGEMENT The enclosures accommodate optical component modules allowing the unit to house splitters, WDMs, filters and other optical components. For splicing applications, TE's splice trays can be installed to support either individual fusion splicing or mass fusion splicing. The units provide sealed cable ports for cables and interconnection cables and gaskets to protect against dust and water spray. The units can also be configured with a standard cable grip kit to provide strain relief for incoming fiber cables. The splice compartment provides ample space for storing loose-tube, ribbon or individual fiber slack. FEATURES * 12-Packs provide for high-density terminations and conserve wall space. * Integrated splice tray offers flexible splice management for individual or mass splicing. * Sealed enclosure protect fibers from dust, water spray, insects and other contaminants. * Dual-hinged design ensures separation of owner/client network segments. * Designed to NEMA-12 * Front and rear layer maximizes wall space utilization for both splicing and interconnect. * Robust steel construction protects fibers against damage and ensures network reliability. * Slotted cable entrance ports allow for rapid cable installation and pass-through capability. * Cable management and routing limits bend radius and adds strain relief. * 216-Tool (can wrench), key lock or padlock offers flexible security options. 15 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Indoor Fiber Distribution Terminals (iFDT) Catalog Number FDT- __ __ __ __ __ N X __ __ __ __ 0 Enclosure Type/Capacity Stub Length A iFDT-12 12 Fiber 000 0 Feet B iFDT-24 24 Fiber 025 25 Feet C iFDT-48 48 Fiber 100 100 Feet D iFDT-72 72 Fiber 200 200 Feet E iFDT-96 96 Fiber 300 300 Feet 500 500 Feet Connector/Adapter Style Singlemode J SC/APC N SC/UPC K LC/UPC Cable Type Pigtails Multimode 9 MMSC 6 MMLC A Bare ribbon pigtail assy B 12 Fiber Soft-Walled Bundle* Stubs Splice Tray 0 No Tray 2 Heat Shrink Fusion 3 Mechanical/Ribbon S Ribbon OSP w/Conn R Ribbon IFC w/Conn T Loose Tube OSP w/Conn V Loose Tube IFC w/Conn *900 micron fiber bundled in a soft jacket. Fiber Count 06 6 Fiber 12 12 Fiber 24 24 Fiber 48 48 Fiber 72 72 Fiber 96 96 Fiber SPECIFICATIONS Installation Type: Fibers: Splice Trays: Cable Ports: Rating: Height: Width: Depth: 16 FDT-A Indoor 12 1 Tray 2 Top; 2 Bottom NEMA-12 7.25" 11.8" 3.25" www.te.com/bns FDT-B Indoor 24 2 Trays 2 Top; 4 Bottom NEMA-12 8" 14" 5" 1-800-366-3891 x73000 FDT-C Indoor 48 4 Trays 2 Top; 4 Bottom NEMA-12 18.75" 14.5" 5" Fax: 1-952-917-3237 12/14 FDT-D Indoor 72 6 Trays 2 Top; 4 Bottom NEMA-12 23.6" 14.56" 5" 109756.2AE FDT-E Indoor 96 8 Trays 2 Top; 4 Bottom NEMA-12 32.5" 14.7" 5" Wall Box Solutions Indoor Fiber Wall Mount Boxes TE's FL1 indoor fiber termination products include a variety of two door wall mount box configurations. These products are designed specifically to act as part of the fiber distribution system in an enterprise networkcell site backhaul network, or as the demarcation point for the service provider at the customer's location. FL1 products utilize adapter pack technology, which enables service providers to add new subscriber connections as needed--deferring unnecessary CAPEX. Excellent labeling, grommets, door latches and ribbon pigtail routing reinforce the value these products bring to the physical layer of any network with higher quality and reliability, greater operational efficiencies, and network simplification. 12-Position FEATURES/BENEFITS * Economical, "build-as-you-grow" solution * Quick installation * Compact size * Durability * Single catalog number ordering * Single package shipping TWO DOOR FIBER WALL MOUNT BOXES The FL1 two-door, wall-mount boxes feature a unique design and many integrated features such as: * Multiple, configurable locking options that allow users and service providers separate access for security * Acceptance of strength member tie-off hardware * Acceptance of cable clamps at each corner SPECIFICATIONS Installation Type: Fibers: Splice Trays: Cable Ports: Rating: Height: Width: Depth: 17 FL1-G Indoor 12 1 Tray 2 Top; 2 Bottom NEMA-12 11.2" (28.4 cm) 13" (33 cm) 3.6" (9.1 cm) www.te.com/bns FL1-H Indoor 24 2 Trays 2 Top; 2 Bottom NEMA-12 15.1" (38.4 cm) 14" (35.6 cm) 3.6" (9.1 cm) 1-800-366-3891 x73000 FL1-J Indoor 48 4 Trays 2 Top; 2 Bottom NEMA-12 17.7" (45 cm) 17" (43.1 cm) 6.2" (15.7 cm) Fax: 1-952-917-3237 12/14 FL1-P Indoor 72 6 Trays 2 Top; 2 Bottom NEMA-12 17.7" (45 cm) 17" (43.1 cm) 6.2" (15.7 cm) 109756.2AE Wall Box Solutions Indoor Fiber Wall Mount Boxes HOW TO ORDER AN FL1 TWO-DOOR WALL MOUNT BOX 1. Select wall box type 2. Select 6pak (with or without fiber) installed in wall mount box 3. Select 6pak adapter type 4. Select splice tray with chip 5. Select number of cable clamps (0-9) 6. Select number of compression fittings (0-9) 7. Select number of bonding grounding kits (0-9) 8. Select number of strength member tie-off kits (each wall box accepts 2, maximum) (0-9) 9. Select locks Catalog Number FL1- __ __ __ __ __ __ __ __ - __ __ __ __ 12 3A 3B 3C 3D 3E 4 Wall Box Type (2-door) G 12-position termination/ splice wall box H 24-position termination/ splice wall box J 48-position termination/ splice wall box P 72-position termination/ splice wall box 3 4 Adapters only - no fiber 6 6-fiber softwall bundle (3 m (12-fiber for LC) 9 12-fiber ribbon (3 m) 6 7 8 Accessories Enter quantity (0-9) above corresponding accessory 5 Cable clamp 6 Compression fittings 7 Bonding grounding kit 8 Strength member tie-off Splice Tray with Chip 6paks Installed into Wall Box Adapters with pigtails (2 mm x 3 m) 5 1 Bare fusion 2 Heat shrink fusion 3 Mechanical (elastomeric) N None Multimode and Singlemode 6pak Adapter/Connector Type N Blank Singlemode 7 SC/UPC ultra polish E SC/UPC duplex J SC/APC angled polish B SC/APC duplex with angled polish 8 LC Multimode 18 www.te.com/bns 1-800-366-3891 x73000 9 SC D SC duplex 6 LC Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions FL1 6pak Adapter Packs PLACEMENT OF 6PAKS 24-Position Wall Mount 12-Position Wall Mount Door Side B A Door Side Wall Mount Side (Rear of Box) TypeType G Box Viewed G Box from Equipment Side C A C B Wall Mount Side (Rear of Box) Type H BoxH Viewed Type Box from Equipment Side (Viewed from Side of Box) (Viewed from Side of Box) 48-Position Wall Mount E Door Side D E D C A Wall Mount Side (Rear of Box) C B Type Type J BoxJ Viewed Box from Equipment Side (Viewed from Side of Box) 72-Position Wall Mount D D B A D D C A D D C B Wall Mount Side (Rear of Box) Door Side Type Type P BoxP Viewed Box from Equipment (Viewed from Side ofSide Box) Note: All configured wall boxes will have adapter packs loaded starting from the wall side. 19 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions FL1 6pak Adapter Packs 6pak Adapter -- Adapters and Pigtails FEATURES * Flexibility for future growth: To add capacity to an existing FL1 wall box, simply order the appropriate 6pak * Can be purchased and installed as growth necessitates 6pak without fiber * Available with preterminated three-meter pigtails * Pigtails consist of a single outer jacket containing six color-coded 900 m fibers * One end of pigtail terminated with chosen connector style and installed into the 6pak adapter * Saves installation time ORDERING INFORMATION 6pak with fiber Description Multimode (62.5/125) - Adapter 6 Packs SC FL2-6PMMSC LC FL2-6PMMLC Singlemode - Adapter 6 Packs SC/APC FL2-6PSMASC SC/UPC FL2-6PSMSC LC FL2-6PSMLC Multimode (62.5/125) with 3 Meters of Fiber SC FL1-6P9BC003 LC FL1-6P6BC003 Singlemode with 3 Meters of Fiber SC/UPC FL1-6P7SC003 SC/UPC angled 8 FL1-6PJSC003 LC FL1-6P8SC003 6pak Adapter (With SC Adapters and Pigtails) 10G 6paks - with 50/125 m Laser Optimized Multimode Pigtails* 10G Multimode LC (aqua), with 3 meter 12 fiber stranded pigtails FL2-6P6JC603W 10G Multimode SC (aqua), with 3 meter 6 fiber stranded pigtails FL2-6P9JC603W 6paks - Singlemode Pigtails and adapters Singlemode LC (blue), with 3 meter 12 fiber stranded pigtails FL2-6P8SC603W Singlemode SC/APC (blue), with 3 meter 6 fiber stranded pigtails FL2-6P7SC603W *10G 6paks utilize 50/125 m laser optimized multimode to 300 meters or OM3 rated glass and aqua colored adapters. 20 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions FL1 6pak Adapter Packs 6pak Connector Plug-Ins and Accessories FEATURES * Completely interchangeable between FL2000 panel and wall box products * C an be ordered with all standard types of simplex and duplex single and multimode adapters and connectors * F eature TE's removable angled retainers which provide superior fiber management 6pak plug-in (shown with singlemode duplex adapters) * No tools required to install into FL2000 boxes or panels ORDERING INFORMATION Description 6pak plug-in (shown with multimode duplex adapters) Catalog Number Multimode (62.5/125) SC FL2-6PMMSC SC (aqua) OM3 50/125 FL2-6PMMSC-A LC FL2-6PMMLC LC (aqua) FL2-6PMMLC-A 6pak plug-in (shown with singlemode simplex adapters) Singlemode SC FL2-6PSMSC LC FL2-6PSMLC 6pak blank plug in FL2-6PBLNK Compression fitting FL1-ACC001 Compression fitting with plate FL1-ACC006 Strength member tie-off kit FL1-ACC003 Cable clamp FL1-ACC011 Bonding grounding kit FL2-ACC004 6pak plug-in (shown with multimode simplex adapters) Locks Lock and Key Type A IPA-K1 Lock and Key Type B IPA-K2 Mini-splice tray (used only in 12-position, wall-mount box) Bare fusion FL1-M-FT Heat shrink (single fiber fusion) FST-M-HS 6pak Adapter-Only Mechanical (mass fusion) FST-M-MT (Without Fiber) Standard splice tray 21 Bare fusion FST-FT Heat shrink fusion (single fiber fusion) FST-HS Mechanical (mass fusion) FST-MT www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Flexible Fiber Box (FFB) TE Connectivity's (TE) flexible fiber box (FFB) is designed to address the unique challenges of indoor, outside plant and fiber installations. Available in two unique base configurations, fixed and Rapid Fiber, the FFB promotes true flexibility with easily interchangeable components for termination, sliding adapter pack, fixed bulkhead, splice, MPO and hardened multifiber optical connector (HMFOC) configurations. The Rapid Fiber FFB system leverages TE's RapidReel fiber cable spool to payout fiber directly from the enclosure. By enabling faster cable routing and installation, the fiber cable spool helps to minimize overall labor costs. In addition, the spooling system reduces the need for site survey inspections, and simplifies cable ordering and inventory requirements. Any excess cable stores easily back on to the spooling system, eliminating the need for additional slack storage equipment. Rapid Fiber FFB The fixed FFB system uses an assortment of fixed configuration plates to mix-andmatch different cable and connector types. One half of the box manages feeder cable connections; the other half manages drop connections. To meet co-location requirements, the feeder side of the box is available with a lockable cover. Fixed FFB TE's flexible fiber box series incorporates the latest in cutting-edge technology, helps to deliver unmatched savings in installation time, labor costs, and offers unrivaled performance for next generation networks.. BENEFITS Flexibility: Designed to serve any network topology, any location, any technology. Protection: Built to withstand harsh environmental conditions including dust, moisture and UV. Fixed FFB with Internal Demarc Door Right-Sized: Enclosure meets space requirements for a variety of environments. Performance: Reduced bend radius fiber cable reduces attenuation caused by tight bends and frequent handling. Easy Installation: Mounts on a wall, pole or other flat surface with minimal tools. SPECIFICATIONS Installation Type Fibers Splice Trays Cable Ports Rating Height Width Depth 22 www.te.com/bns Indoor/Outdoor 24 2 Trays 4 Bottom NEMA-4, UL 10.5" (.26 m) 12" (.3 m) 5" (.12 m) 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Flexible Fiber Box (FFB) Preconfigured Rapid Fiber FFB Preconfigured Rapid Fiber FFB units are available to ship from the factory with preinstalled RapidReel fiber cable spools, sliding adapter packs, splice trays and/or preterminated cable assemblies, and help to simplify the ordering process and reduce installation time and cost. ORDERING INFORMATION Description Cable Type Fibers 12 Singlemode 24 Rapid Fiber FFB Sliding Adapter Pack Option 12 Multimode 24 12 Singlemode 24 Rapid Fiber FFB Splice Option 12 Multimode 24 Connector Type Part Number LC-MPO FFB-R012ESKSSDUXXX SC-MPO FFB-R012ES7SSDUXXX LC-MPO FFB-R024ESKSSDUXXX SC-MPO FFB-R024ES7SSDUXXX LC-MPO FFB-R012MSCSSFUXXX SC-MPO FFB-R012MSTSSFUXXX LC-MPO FFB-R024MSCSSFUXXX SC-MPO FFB-R024MSTSSFUXXX MPO (far end) FFB-R012ES22SDUXXX Stub (far end) FFB-R0120S22SDUXXX MPO (far end) FFB-R024ES22SDUXXX Stub (far end) FFB-R0240S22SDUXXX MPO (far end) FFB-R012MS22SFUXXX Stub (far end) FFB-R0120S22SFUXXX MPO (far end) FFB-R024MS22SFUXXX Stub (far end) FFB-R0240S22SFUXXX Rapid Fiber FFB - LC or SC Connectors Rapid Fiber FFB - Splice Tray XXX= 031 061 076 092 123 153 183 213 244 274 305 100' Spooled (31 m) 200' Spooled (61 m) 24 Fiber requires ext. spool 250' Spooled (76 m) 24 Fiber requires ext. spool 300' Spooled (92 m) with ext. spool 400' Spooled (122 m) with ext. spool 500' Spooled (153 m) with ext. spool 600' Spooled (183 m) with ext. spool 700' Spooled (213 m) with ext. spool 800' Spooled (244 m) with ext. spool 900' Spooled (274 m) with ext. spool 1000' Spooled (305 m) with ext. spool NOTE: he FFB is available with a maximum of 1000' of T spooled cable. 23 www.te.com/bns 1-800-366-3891 x73000 FFB with external fiber spool. Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Flexible Fiber Box (FFB) Preconfigured Fixed FFB Preconfigured fixed FFB units are available to ship from the factory with preinstalled connectors, adapter packs, splice trays, cables and/or preterminated pigtail assemblies, and help to simplify the ordering process and reduce installation time and cost. ORDERING INFORMATION Product Description Fibers 12 Feeder: MPO Drop: Sliding Adapter Type 24 12 Feeder: HMFOC Drop: Sliding Adapter Type Feeder: External HMFOC Input with Demarc Door (Sliding Adapter Type Shown) Part Number LC FFB-F012EMSKSSDDUX SC FFB-F012EMS7SSDDUX LC FFB-F024EMSKSSDDUX SC FFB-F024EMS7SSDDUX LC FFB-F012UMSKSSDDUX SC FFB-F012UMS7SSDDUX LC FFB-F024UMSKSSDDUX SC FFB-F024UMS7SSDDUX 12 - FFB-F01222SOVS0000 24 - FFB-F02422SOVS0000 LC FFB-F01200HKSSDDUD SC FFB-F01200H7SSDDUD 24 Feeder: Splice Drop: VAM (Order VAM modules separately. See the full catalog for details.) Connector Type 12 24 12 Feeder: Splice Drop: Sliding Adapter Type 24 12 Feeder/Drop: Fixed Adapter Type in Center 24 12 Feeder: MPO Drop: Fixed Adapter Type Plate 24 LC FFB-F02400HKSSDDUD SC FFB-F02400H7SSDDUD LC FFB-F01222SKSSDDUX SC FFB-F01222S7SSDDUX LC FFB-F02422SKSSDDUX SC FFB-F02422S7SSDDUX LC FFB-F012KCSK0SA00X SC FFB-F0127CS70SA00X LC FFB-F024KCSK0SA00X SC FFB-F0247CS70SA00X LC FFB-F012EMSKFSDDUX SC FFB-F012EMS7FSDDUX LC FFB-F024EMSKFSDDUX SC FFB-F024EMS7FSDDUX Replace X with "D" to include internal demarc door, or "0" to exclude door. 24 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Fiber Splitter Box (FSB) TE's fiber splitter box (FSB) enables service providers to accelerate their deployments more effectively and is an ideal solution when deploying networks in customer premises applications. These wall boxes provide a small footprint for splitting, splicing and terminating and are environmentally rated for indoor or outdoor use. Available in three sizes, each box is equipped with a 12-fiber splice tray allowing for an input splicing option. FSB's accept standard plug and play (PNP) splitters and splitters can be easily added after the wall box has been installed. FSB's accommodate 1x4, 1x8, 1x16 and 1x32 splitters; up to 72 fibers. FSB's offer increased efficiency within distinct FTTX network applications. Featuring a compact solution for wall mounting, these boxes provide a significant space savings while maintaining hand access to connectors. The unique swing frame design also allows for easy access to the back section of the wall box. FSB's small size and flexible mounting options offer easy integration into cell sites and huts--providing on-demand capacity for wireless backhaul applications. For serving facilities in rural locations, i.e. strip malls, FSB's offer an economical solution where installing larger sized FDH's may be unfeasible. FSB-16 - Indoor or Outdoor Enclosure FEATURES AND BENEFITS * Accommodates up to 16 ports * Rated for indoor or outdoor use * Traditional swing frame design allows for access to the back section of the wall box * Splitter can be easily installed after wall box install * Standard 12-fiber splice tray allows for input splicing option * Output pigtails can either be stored internally or routed externally * Accepts standard PNP splitter 25 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Fiber Splitter Box (FSB) FSB-32 - Indoor Enclosure FEATURES AND BENEFITS * Dual hinge design creates separation between rear splitter section and front customer side access * Splitters can be easily installed after wall box install allowing for separate purchase * Standard 12-fiber splice tray allows for input splicing option * Accommodates up to 32 splitter ports for one splitter module * Dual hinge provides small footprint on the wall while maintaining excellent hand access to connectors * Accepts standard PNP splitter FSB-72 - Outdoor Enclosure FEATURES AND BENEFITS * Traditional swing frame design allows for access to the back section of the wall box * Splitter can be easily installed after wall box install * Standard 12-fiber splice tray allows for input splicing option * Accommodates up to 3 PNP splitter modules * 72 port capacity with built-in 32-port parking * Easily wall mounts to buildings * Accepts standard PNP splitter SPECIFICATIONS Installation Type Fibers Splice Trays Splitter/WDM Ports Rating Height Width Depth 26 www.te.com/bns FSB-16 (H) Indoor/Outdoor 16 1/12f 1 NEMA-4 9" 9" 3.5" 1-800-366-3891 x73000 FSB-32 (B) Indoor 32 1/12f 1 NEMA-12 8" 13" 5" Fax: 1-952-917-3237 FSB-72 (G) Outdoor 72 5/12f 3 NEMA-4 13" 19" 10" 12/14 109756.2AE Wall Box Solutions Fiber Splitter Box (FSB) Catalog Number FSB- __ __ __ __ __ __ __ __ __ __ __ __ __ 1 2 3 4 5 6 7 8 9 10 11 1 Configuration S 11 Key Locks Standard 2 Enclosure Type Code Description Capacity Size (HxWxD) B Indoor FSB-32 32-Fiber 8"x13.5"x5" G Outdoor FSB-72 72-Fiber 13.5"x19"x8" H Indr/Outdr FSB-16 16-Fiber 9"x9"x3.7" 0 None (Pad Lock Ready) A Front Lock 1, Rear Lock 1 B Front Lock 1, Rear Lock 2 C Front Lock 1, No Rear Lock D Rear Lock 2, No Front Lock 10 Feeder Fiber Count 0 3 Connector Type No Stub 2 2 Fibers 4 4 Fibers J SC/APC 6 6 Fibers N SC/UPC 8 8 Fibers 9 Feeder Cable Length 4 Splice Tray (Feeder Side) 000 0 Feet 025 25 Feet 2 Heat Shrink Fusion 3 Mechanical/Ribbon 100 100 Feet 0 No Splice Tray 200 200 Feet 300 300 Feet 500 500 Feet 5 Fiber Count (Distribution) 12 12 Fibers 16 16 Fibers 32 32 Fibers 48 48 Fibers 72 72 Fibers 8 Cable Type (Feeder Cable) Adapters Adapters Only (No Pigtail for Feeder) 0 Pigtails A Splice-Ribbon Pigtail Assy C Splice-Pigtails (900 Micron) 6 Splitter Type Installed 0 None Installed A 1x32 Standard C 1x16 Standard J 1x8 Standard L Dual 1x8 Standard M Dual 1x16 Standard N 1x4 Standard P 2x16 Standard U Dual 1x4 Standard Stubs www.te.com/bns 1-800-366-3891 x73000 Ribbon OSP Cable Ribbon IFC Cable T Loose Tube OSP Cable V Loose Tube IFC Cable M 900um IFNR Cable 7 Splitter Qty Installed 0 27 S R Fax: 1-952-917-3237 12/14 None 1 One (1) Installed 2 Two (2) Installed 3 Three (3) Installed 109756.2AE Wall Box Solutions Premises Patch and/or Splice Enclosure - FibrBoss PB 06-S The FibrBoss PB06-S premises splice enclosure is designed for low count indoor or outdoor splicing applications. This product is wellsuited as a demarcation splice point between the service provider and customer or for "handoff" splicing of fibers whereby the service provider supplies fibers for use by a third party. This compact enclosure design includes a rugged plastic housing with a single covered fiber management tray for both fiber storage and splice storage. Cable retention brackets are integrated into the tray and splice protection sleeves are included with the enclosure for added customer convenience and efficiency. FEATURES AND BENEFITS * Intended as a small splice or fiber "hand-off" enclosure * UL listed and UV resistant enclosure * Tie-wrap door security is standard * Small size (5" x 4" x 2" interior dimensions) * Accommodates field supplied fl at or round drop cable inputs * Accommodates field or factory supplied pigtail outputs * Fiber storage and splices integrated on one tray - tray cover included * Six position splice sleeve holder on tray * Six splice sleeves included * Output pigtails are optional Catalog Number F - PB06 - SA2 - R __ __ - __ __ __ __ __ - O __ Pigtail Count N Pigtail Packaging N No pigtails N No pigtails 0 2 Two pigtails 2 Pigtails included, not installed 0 4 Four pigtails 0 6 Six pigtails Pigtail Length (Meters) 0 No pigtail 0 1 1 m pigtail N None 0 3 3 m pigtail 0 6 6 m pigtail Connector Type N 0 S 1 SC/UPC S 2 SC/APC L 1 LC/UPC L 2 LC/APC Pigtail Type N No pigtails B 1.8 mm OFNR cord Pigtails are only included when option 3 in "Pigtail Packaging" is selected. 28 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Premises Patch and/or Splice Enclosure - FibrBoss PB 06-B The FibrBoss PB06-B six-connector fiber premises box is intended to be used to patch and splice up to six fibers in an environmentally secure housing in an indoor or outdoor wall mounted application. Incoming fiber optic cables up to 10mm OD can be accommodated by this enclosure. This compact design includes a rugged plastic housing with a combination patching (top) and splicing (bottom) tray. The patching features of the tray include bend controls and integrated fiber retention clips for proper pigtail management. The splicing features of the tray include a covered fiber management tray for both fiber storage and splice storage. Cable retention brackets are integrated into the tray, and splice protection sleeves are included with the enclosure for added customer convenience and efficiency. FEATURES AND BENEFITS * Intended as a small patch and splice or fiber "hands-off" enclosure * UL listed and UV resistant enclosure * Small size (4.8" x 6.4" x 2.4" interior dimensions) * Accommodates field supplied flat or round drop cable inputs * Accommodates field supplied cable and pigtail outputs * Fiber storage and splices integrated on one tray - tray cover included * Six position splice sleeve holder on tray * Six splice sleeves included * Mounting features for wall, pole, or pedestals * Optional security screw for the fiber tray for use as a demarcation enclosure (contact customer service) Catalog Number F - PB06 - BC2 - R __ __ - __ __ __ __ __ - O __ Pigtail Count Pigtail Packaging N N No Pigtails 0 2 Two Pigtails N No Adapters, No Pigtails 0 4 Four Pigtails 2 0 6 Six Pigtails Adapters and Internal Pigtails Included and Installed 5 Adapters Included and Installed, No Pigtails Connector Type N N None S 1 SC/UPC S 2 SC/APC 0 0 No Pigtails L 1 LC/UPC (Limited to 6 pigtails total) 0 1 One-Meter Pigtails L 2 LC/APC (Limited to 6 pigtails total) Number of Adapters (and pigtails if selected) Pigtail Fiber/Cable Type (Singlemode) 29 N No Pigtails A 900um Buffer, Color Coded (Internal Pigtails Only) www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Wall Outlets - OWB-S (Outdoor Wall Mounted Small Box) OWB-S (Outdoor Wall Mounted Small Box) The OWB-S is a small wall-mountable fibre box, providing an environmental and mechanical protection for the fibre management system that includes the functions of storage, splicing, patching and passive component integration. This product is designed for wall location, typically used as a premises connection device in FTTH networks, but can also be used in other outdoors above-ground applications. A variety of possible configurations are accommodated. FEATURES AND BENEFITS * Compact size * High seal rate: IP65 * LSZH & UV resistant * Hinge + latch design allows easy access * Multiple cable entry points CABLE PORT * Wall or pole mountable 3x5.4mm (figure 8) OD up to 5mm OD up to 10mm * Optional padlock SPECIFICATIONS Installation Type Fibers Splice Trays Cable Ports Rating Height Width Depth 1 on top + 1 on bottom 1 on rear + 4 on bottom Each on both sides DIMENSIONS (MM) Outdoor 4 1/12f 1 top; 3 Bottom IP65 seal rate; LSZH & UV resistant 209.8 mm 173.8 mm 72 mm ORDERING INFORMATION Catalog Number OWB - S - _ _ - __ _ - __ - _ Splice type Mounting Kit N No splicing application N None R RECORDsplice mechanical splice W Wall mounting kit P Pole mounting kit S Fusing splice Number of splice protector 0-12 Number of splice protector S1 SC/UCP S2 SC/APC NN None 30 www.te.com/bns Splitter integrated NN None Number of adapters 0-4 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Wall Outlets - Rapid Fiber Faceplate Rapid Fiber Faceplate The Rapid Fiber faceplate incorporates a unique spooling system for integrated cable storage, with the ability to store up to 30 meters of 1.2 mm cable behind a low profile wall outlet. The 1.2 mm cable is terminated to a low loss SCA connector terminated at the outer end with a small profile dust cap / hauling eye solution for internal cable hauling. The inner end of the cable is presented within a low loss SCA adapter with integrated laser safety shutter. BENEFITS * Greatly reduces time to install and removes craft sensitivity * Removes the need for field termination at time of customer connect * Reduces inventory items, utilizing only standard items * Removes the need for extensive site survey * Simple installation technique, no specialist tools required * Compatible with multifiber pass through cables up to 8 mm diameter * Cables up to 4.8 mm* can be accommodated within the faceplate FEATURES * Up to 30 m of internal cable storage facility * Integrated SCA dust cap / hauling eye * Suitable for cavity mount installations or surface mount installation * 1.2 mm G657.B3 micro cable technology * Accommodates up to 2F splice tray incorporated into base of the faceplate * Integrated cable pass-through functionality * Standalone faceplate or supplied with 30 or 60 m of pre-terminated 1.2 mm cable * *Limited routing options available ORDERING INFORMATION Catalog Number RFP - __ - __ __ - __ __ - __ - __ - __ - __ __ Number of Fibers 0 No fiber 1 1 fiber Specific Logo TE TE logo Mounting Solution Spool Length X No mounting required 0 No spool W Surface mount 30 30 meters C Cavity mount 60 60 meters Adapter Type Connector Type L S2 SC/APC S1 SC/UPC Low loss (0.1 dB max) Number of Adapters 1 31 1 adapter www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Wall Outlets - Customer Wall Outlet (COWO) Customer Wall Outlet (COWO) COWO is a fiber optic customer outlet that allows easy and unobtrusive termination of fiber optic cables in an office, home or communications room. FEATURES AND BENEFITS * Accommodates two termination/splice connections -- 2 SC simplex or 1 LC duplex adapters -- 2 crimp, mechanical or heat shrink splices * IP20 rated * Very flat design, mounts on a standard flush mount electrical outlet * Utilizes reduced bend radius fiber (G657.a and B) * Possibility to invert the adapter in the holder to prevent disconnection when pulling the patch cords * RoHS compliant * Conforms to UL 94 V-O * Lockable with screw or lead-wire seal * Cable entrance from the bottom, left and rear * Made of molded plastic (halogen free, LSZH-1), white (RAL 9010) TECHNICAL DATA Number of input cable positions Input cable diameter Max. capacity Max. number of customer feeds Operating temperature Material 4 3-7 mm 2 fibers 2 patch cords -40C to +70C PC-FR ORDERING INFORMATION Catalog Number COWO - ____ __ __ Connector type Number of adapters S1 SC/UPC 0 S2 SC/APC 1 2 L1 LC/UPC L2 LC/APC NN None for cable splicing Number of pigtails 0 1 2 ACCESSORIES For cable splicing, a strain relief can be installed instead of an adapter at the same position. FTX-7029 1 900-30 Strain Relief for TWO cable up to 3,0mm diameter FTX-7029 1 900-50 Strain Relief for ONE cable up to 4,2mm diameter 32 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Wall Outlets - Transition Box with DLX Adapters Transition Box with DLX Adapters DESCRIPTION This outside plant transition box offers the ultimate "plug-and-play" solution for durable and reliable service connection in the outside plant/drop segment of the network. The technician-friendly design greatly simplifies installation and maintenance by minimizing splicing required at the customer's premises. The cost-effective solution provides lower overall installed costs throughout the FTTX network. Rather than having to break a splice, technicians can troubleshoot or perform routine maintenance by simply unplugging a connector FEATURES AND BENEFITS * Accommodates up to two DLX - terminations * Made of molded plastic (UL94-V0) * IP54 rated * Wall- or Pole mount * Utilizes reduced bend radius fiber (G657.A and B) * Lockable with screw or lead-wire seal * Cable entrance from bottom and rear TECHNICAL DATA Number of input cable positions:: Input cable diameter: Maximum capacity: Material: Color: Operating temperature: Environmental Characteristics: Dimensions (H x W x D): 2 3-5mm 2 fibres Polystryrol-blend (ASA) RAL 7032 light grey -30 C to +70 C IP54 rated RoHS compliant 90 x 63 x 50 mm ORDERING INFORMATION Description Product Catalog Number Transition box 1 DLX hardened connector FTX-7029 1 007-01 2 DLX hardened connector FTX-7029 1 007-02 33 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Wall Outlets - FTUO (Fiber Termination Unit Outdoor) FTUO (Fiber Termination Unit Outdoor) This box is typically used as a transition point where the OSP cable is spliced to an indoor cable. FEATURES AND BENEFITS * Compact enclosure (168 x 132 x 33 mm) * The box allows the installation of fibers with a minimum bend radius of 25 mm over a length of 2m. * In-line and butt configuration possible for main cable * Universal splice holder for 8 splices: SMOUV, ANT, RECORDsplice. * Ready for TE Connectivity OCC1 splitter installation * Cable inlet is provided at the bottom left side. Optionally the main cable can continue at the top left side. (wraparound pass-through) * Cable outlet ports (max. 2 cables) are provided at 5 sides: left, right, top, bottom, back * IP 43 when cable enters from bottom; * IP40 when cable enters from top KIT CONTENT: * Impact rating: IK08 * UV resistant housing -- Box with base, fiber organizer, cover * Standard colour: RAL7035 grey -- Main cable seal + tiewraps + foam * Gasventing provided -- Drop cable seals for 2 drops and cable fixation accessories * Locking with screw, optionally security seal -- Universal splice holder for 8 splices (SMOUV, ANT, RECORDsplice) * Main cable up to 12 mm diameter * Drop cable up to 5 mm diameter ORDERING INFORMATION Catalog Number FTUO - _ - _ - __ - 1 Connector type M Number of adapters size = medium NN Number of pigtails U Splice holder type = Universal splice holder (for SMOUV, ANT, RECORDsplice), 8 splices ACCESSORIES FTUO-USEAL-01 FTUO-OSEAL-01 CPWO-LABEL-7035-(1000) 34 additional main cable seals (MOQ/SPQ = 500 pcs) additional drop cable seals (MOQ/SPQ = 1000 pcs) security label to cover the access screw (RAL7035 colour) (MOQ/SPQ = 1000 pcs) www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Wall Outlets - Customer Premises Wall Outlet (HFTP) Customer Premises Wall Outlet (HFTP) The HFTP is a compact fiber wall outlet for use at the final fiber termination point in the customer premises. The HFTP provides mechanical protection and managed fiber control in an attractive format suitable for use inside customer premises. A variety of possible fiber termination techniques are accommodated. FEATURES AND BENEFITS * Splicing to factory terminated pigtails * Positive fiber management * Direct termination with field installable connectors * Attractive design for indoor use * Can hold up to 4 mechanical splices (RECORDsplice) and fusion splice protectors (SMOUV and ANT) and mechanical SC connectors can be integrated as well * Splice cable to cable * Compatible with 2 SC Simplex adaptors * Multiple cable entry points (cable diameter 6mm) * Can be wall mounted and mounted on wall boxes with fixation points of 60mm * Laser safe with individual shutters Catalog Number HFTP - NO - __ __ __ __ - __ Connector type Mounting kit S1 No pigtails S2 Two pigtails NN Four pigtails L1 LC/UPC L2 LC/APC LN No pigtails and adaptors but with LC shutters E Expansion screws Number of adapters 0 1 2 Number of pigtails 0 1 2 4 (LC only) ACCESSORIES CPWO-LABEL-(1000) Access screw cover and security label (MOQ/SPQ = 1000 pcs) NOTE HFTP-N0-NN00-E and HFTP-N0-LN00-E have an MOQ of 10 pcs All other items have an MOQ = SPQ = 300 pcs Packaging: 10 pieces per box 35 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Accessories Fiber Connector/Adapter Cleaning Kit The fiber connector/adapter cleaning kit contains all the items required to adequately clean fiber connectors and adapters. The performance of an optical fiber system is largely dependent on the fiber connector cleaning procedures followed prior to installation. It is suggested that all the connectors and adapters be cleaned before making any connections. The kit cleans approximately 500 connectors or adapters. ORDERING INFORMATION Description Catalog Number Fiber connector/adapter cleaning kit FPC-CLNKIT Cleaning Kit Includes: * Instruction sheet * Lint-free wipes * Isopropyl alcohol * Cotton swabs * Lint-free pipe cleaners * Oil-free compressed air This kit contains flammable alcohol and compressed air. For this reason, it can be shipped by surface method only. 36 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Accessories Fiber Inspection Kit ORDERING INFORMATION Quantity Catalog Number Optical Fiber Inspection and Cleaning Kit for Standard Connector Styles (LC, SC, ST, FC), MT-RJ, and MPO. Kit includes everything needed to perform routine fiber maintenance and troubleshooting including cleaning tools, an inspection microscope, a visual fault locator, and a CD-ROM with detailed inspection, cleaning instructions and a rugged carrying case. Kit components: Product Description Image A 1 2064651-1 Visual Fault Locator (VFL)) with 1.25 MM Adapter B 1 1828352-2 200x Microscope with 2.5 mm Adapter C 1 1754767-1 1.25 mm (LC) Microscope Adapter D 1 1754765-1 MT-RJ Microscope Adapter E 1 1754768-1 MPOA Microscope Adapter F 1 1828837-1 MPO Microscope Adapter G 1 1828836-1 Termination Training, CD-ROM H 1 2064710-1 2.5 mm Stick Cleaners (10/package) I 5 1918807-1 1.25 mm Stick Cleaners (10/package) J 5 1918808-1 One Slot Reel Cleaner K 1 1918803-1 MT-RJ w/pins Reel Cleaner L 1 1918804-1 SC in Bulkhead Cleaner (IBC) M 1 2064499-1 LC IBC N 1 2064500-1 MPO IBC O 1 1918809-1 Premium Hard Case P 1 TBD 37 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Accessories Accessories - Protective Tubing Cutting Tool The protective tubing cutting tool is used to score the protective tubing so the tubing can be cut to the appropriate lengths for the final installation. ORDERING INFORMATION Product Description Catalog Number Protective tubing cutting tool BLK-BK0TUB Accessories - Grounding Kit Set Screws Cable Assembly Lug Kit used to ground armored fiber cable. 10-24 Screw ORDERING INFORMATION Product Description Grounding Kit (GAK-FEC001 Shown) Catalog Number Grounding kit for; A rmored OSP cable Includes: One cable assembly lug type ground kit One #6 ground cable 229 mm (9") long ny armored loose tube or buffer tubed fiber A OSP cable Includes: One bullet ground connector One #6 ground cable 127 mm (5") long rame mount configuration F Any armored loose tube or buffer tubed OSP cable Includes: One bullet ground connector One #6 ground cable 305 mm (12") long GAK-FEC001 2 Securing Nuts Top GND-STPKIT Base Bullet Ground Connector FEC-ACCGND02 #6 Ground Cable Grounding Kit (GND-STPKIT Shown) Grounding/Moisture Blocking Kits Kit used to properly block gel filled stranded and ribbon cables. ORDERING INFORMATION Product Description Catalog Number Grounding/Moisture blocking kit; Includes components for grounding and blocking gel filled fiber cables: blocking gel, heat shrink and grounding accessories FBK-0SP002 Moisture blocking kit; Includes components for blocking gel filled fiber cables: syringe, blocking gel BLK-MSTRKIT 38 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE Wall Box Solutions Accessories Accessories - Splice Protector Sleeve The splice protector sleeve is constructed to protect a splice post fusion. It is made from heat shrinkable material and contains a built-in strength member for physical protection of the fusion splice. The splice protector sleeve is placed on the fiber before making a splice, moved over the splice when the splice fusion is complete and shrunk into place. They are available in either single fiber or mass fusion sleeves. Splice Protector Sleeve (FST-ACC001 Shown) ORDERING INFORMATION Product Description Catalog Number Splice protector sleeve for Single fiber - single fusion; 60 mm (2.4") length, 1 each FST-ACC001 Single fiber - single fusion; 40 mm (1.6") length, 1 each FST-ACC005 12-fiber - mass fusion - heat shrink; 40 mm (1.6") length, 1 each FST-ACC006 Accessories - 216 Tools - Can Wrench Keys ORDERING INFORMATION Product Description Catalog Number Nickel plated brass can wrench key For use in loosening/tightening security screws OSP-216BKEY1 Aluminum can wrench key For use in loosening/tightening security screws OSP-216BKEY2 Plastic can wrench key For use in loosening/tightening security screws OSP-216BKEY3 39 www.te.com/bns 1-800-366-3891 x73000 Fax: 1-952-917-3237 12/14 109756.2AE te.com TE Connectivity, TE connectivity (logo) and Every Connection Counts are trademarks. All other logos, products and/or company names referred to herein might be trademarks of their respective owners. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity`s obligations shall only be as set forth in TE Connectivity`s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. (c) 2014 TE Connectivity Ltd. family of companies 106756.2AE 12/14 All Rights Reserved. Revision BROADBAND NETWORK SOLUTIONS /// WALL BOX SOLUTIONS CATALOG Contact us P.O. Box 1101 Minneapolis, Minnesota USA 55440-1101 Tel: 1-800-366-3891 x73000 1-952-917-3000 Fax: 1-952-917-3237 www.te.com/bns Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: TE Connectivity Divested: 1435797-3