BQ7692000PW - Texas Instruments

Product

Folder

Order

Now

Technical

Documents

Tools &

Software

Support &

Community

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. UNLESS OTHERWISE NOTED, this document contains PRODUCTION

DATA.

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

bq769x0 3-Series to 15-Series Cell Battery Monitor Family

for Li-Ion and Phosphate Applications

1 Introduction

1.1 Features

• AFE Monitoring Features

– Pure Digital Interface

– Internal ADC Measures Cell Voltage, Die

Temperature, and External Thermistor

– A Separate, Internal ADC Measures Pack

Current (Coulomb Counter)

– Directly Supports up to Three Thermistors

(103AT)

• Hardware Protection Features

– Overcurrent in Discharge (OCD)

– Short Circuit in Discharge (SCD)

– Overvoltage (OV)

– Undervoltage (UV)

– Secondary Protector Fault Detection

• Additional Features

– Integrated Cell Balancing FETs

– Charge, Discharge Low-Side NCH FET Drivers

– Alert Interrupt to Host Microcontroller

– 2.5-V or 3.3-V Output Voltage Regulator

– No EEPROM Programming Necessary

– High Supply Voltage Absolute Maximum (Up to

108 V)

– Simple I2C™ Compatible Interface (CRC

Option)

– Random Cell Connection Tolerant

1.2 Applications

• Light Electric Vehicles (LEV): eBikes, eScooters,

Pedelec, and Pedal-Assist Bicycles

• Power and Gardening Tools

• Battery Backup and UPS Systems

• Wireless Base Station Backup Systems

• 12-V, 18-V, 24-V, 36-V, and 48-V Battery Packs

1.3 Description

The bq769x0 family of robust analog front-end (AFE) devices serves as part of a complete packmonitoring

and protection solution for next-generation, high-power systems, such as light electric vehicles, power

tools, and uninterruptible power supplies. The bq769x0 is designed with low power in mind: Sub-blocks

within the IC may be enabled/disabled to control the overall chip current consumption, and a SHIP mode

provides a simple way to put the pack into an ultra-low power state.

Device Information(1)

PART NUMBER PACKAGE BODY SIZE (NOM)

bq76920 TSSOP (20) 6.50 mm × 4.40 mm

bq76930 TSSOP (30) 7.80 mm × 4.40 mm

bq76940 TSSOP (44) 11.00 mm × 4.40 mm

(1) For all available packages, see the orderable addendum at the end of the data sheet.

Rsns

100

0.1 µF

4. 7 µF

BAT

VC5

VC4

VC3

VC2

VC1

VSS

SCL

SDA

CHG

DSG

REGSRC

REGOUT

SRN

SRP

VC0

CAP1

TS1 Cf

100

0.1 µF

1 µF

1M1M

10k

ALERT

PUSH- BUTTON FOR BOOT

VCC

GPIO

SDA

SCL

VSS

1 µF

0.1 µF

10 kΩ

PACK +

PACK–

Companion

Controller

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

1.4 Simplified System Diagram

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Table of Contents

1 Introduction............................................... 1

1.1 Features .............................................. 1

1.2 Applications........................................... 1

1.3 Description............................................ 1

1.4 Simplified System Diagram........................... 2

2 Revision History ......................................... 3

3 Description (Continued)................................ 5

4 Device Comparison Table.............................. 5

5 Pin Configuration and Functions..................... 6

5.1 Versions .............................................. 6

5.2 bq76920 Pin Diagram ................................ 7

5.3 bq76930 Pin Diagram ................................ 8

5.4 bq76940 Pin Diagram ............................... 10

6 Specifications........................................... 12

6.1 Absolute Maximum Ratings......................... 12

6.2 ESD Ratings ........................................ 12

6.3 Recommended Operating Conditions............... 12

6.4 Thermal Information................................. 14

6.5 Electrical Characteristics............................ 14

6.6 Timing Requirements ............................... 19

6.7 Typical Characteristics.............................. 20

7 Detailed Description ................................... 21

7.1 Overview ............................................ 21

7.2 Functional Block Diagram........................... 21

7.3 Feature Description ................................. 22

7.4 Device Functional Modes ........................... 32

7.5 Register Maps....................................... 34

8 Application and Implementation .................... 46

8.1 Application Information.............................. 46

8.2 Typical Applications ................................. 47

9 Power Supply Recommendations .................. 53

10 Layout .................................................... 54

10.1 Layout Guidelines................................... 54

10.2 Layout Example..................................... 54

11 Device and Documentation Support ............... 57

11.1 Documentation Support ............................. 57

11.2 Related Links........................................ 57

11.3 Community Resources.............................. 57

11.4 Trademarks.......................................... 57

11.5 Electrostatic Discharge Caution..................... 57

11.6 Glossary............................................. 57

12 Mechanical, Packaging, and Orderable

Information .............................................. 57

2 Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision F (November 2015) to Revision G Page

• Changed Electrical Characteristics table to clarify the accuracy of the ADC in different temperature ranges.......... 15

Changes from Revision E (November 2014) to Revision F Page

• Changed bq7693002 From: Product Preview To Production in the Device Comparison Table............................ 5

• Added bq7693007 device to the Device Comparison Table.................................................................... 5

• Changed table note to group ground reference in bq76930 Pin Functions................................................... 8

• Changed table note to group ground reference in bq76940 Pin Functions ................................................. 10

• Changed 10th cell to 11th cell in the Description of pin 29 ................................................................... 11

• Changed table formats for online data sheet ................................................................................... 12

• Changed Handing Ratings table to ESD Ratings............................................................................... 12

• Changed note for R1 on Figure 7-3............................................................................................... 28

• Added more description to the Communications Subsystem section ........................................................ 31

• Changed "SHUTA" to "SHUT_A" and "SHUTB" to "SHUT_B" in the SHIP Mode section ................................ 33

• Changed CAUTION verbiage (editorial).......................................................................................... 33

• Changed the SHUT_A, SHUT_B bit descriptions in the SYS_CTRL1 (0x04) table........................................ 37

Changes from Revision D (July 2014) to Revision E Page

• Added a note to the Absolute Maximum Ratings table ........................................................................ 12

• Changed the Handling Ratings.................................................................................................... 12

• Added the cross-reference to a new table note at VALERT_IH in Electrical Characteristics ................................. 18

• Added a new table note ............................................................................................................ 18

• Added the Typical Characteristics section ....................................................................................... 20

• Changed the Alert section ......................................................................................................... 30

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

• Changed verbiage in Communications Subsystem ............................................................................ 31

• Deleted the READ/WRITE RSVD register in the Register Map............................................................... 34

• Deleted the READ ONLY register information in the Register Map .......................................................... 34

• Changed the reset for Bit 3 in the PROTECT3 register ....................................................................... 39

• Changed wording in the ADCGAIN bit descriptions ........................................................................... 44

• Added Application and Implementation note .................................................................................... 46

• Added Design Requirements ...................................................................................................... 49

• Added the Detailed Design Procedure ........................................................................................... 50

• Changed the Layout Guidelines................................................................................................... 54

• Changed the Layout Example .................................................................................................... 54

• Added a Caution .................................................................................................................... 54

• Changed the Good Layout figure ................................................................................................. 55

• Changed the Weak Layout figure ................................................................................................ 56

Changes from Revision C (May 2014) to Revision D Page

• Changed table reference in Integrated Hardware Protections ................................................................ 27

• Changed paragraph 4 verbiage of Integrated Hardware Protections ........................................................ 27

Changes from Revision B (April 2014) to Revision C Page

• Changed the documentation format ............................................................................................... 1

• Changed some devices from Product Preview to Production Data............................................................ 5

• Changed a bit name in the PROTECT1 register ............................................................................... 38

• Changed a bit name in the ADCGAIN2 register ................................................................................ 45

Changes from Revision A (December 2013) to Revision B Page

• Changed title of the data manual .................................................................................................. 1

• Changed Ordering Information table to ........................................................................................... 5

• Changed some devices to Product Preview ...................................................................................... 5

• Changed Rfmax value in the Recommended Operating Conditions table ................................................. 13

• Changed verbiage in mmunications Subsystem ............................................................................... 31

• Changed SYS_STAT D6 bit name in the Register Map ....................................................................... 34

Changes from Original (October 2013) to Revision A Page

• Changed some devices from Product Preview to Production Data............................................................ 5

• Changed the tINDCELL test condition in Electrical Characteristics.............................................................. 15

• Deleted duplicate CELLBAL3 table ............................................................................................... 36

• Changed bq76940 with bq783xx Companion Controller IC Schematic...................................................... 49

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

(1) Product Preview only

3 Description (Continued)

The bq76920 device supports up to 5-series cells or typical 18-V packs, the bq76930 handles up to 10-

series cells or typical 36-V packs, and the bq76940 works for up to 15-series cells or typical 48-V packs. A

variety of battery chemistries may be managed with these AFEs, including Lithium Ion, Lithium iron

phosphate, and more.

Through I2C, a host controller can use the bq769x0 to implement many battery pack management

functions, such as monitoring (cell voltages, pack current, pack temperatures), protection (controlling

charge/discharge FETs), and balancing. Integrated A/D converters enable a purely digital readout of

critical system parameters, with calibration handled in TI’s manufacturing process.

4 Device Comparison Table

TUBE TAPE & REEL CELLS I2C ADDRESS (7-Bit) LDO (V) CRC PACKAGE

bq7692000PW bq7692000PWR

3–5 0x08

2.5 No

20-TSSOP (PW)

bq7692001PW(1) bq7692001PWR(1) Yes

bq7692002PW(1) bq7692002PWR(1)

3.3

bq7692003PW bq7692003PWR Yes

bq7692006PW bq7692006PWR 0x18 No

bq7693000DBT bq7693000DBTR

6–10

0x08

2.5 No

30-TSSOP (DBT)

bq7693001DBT bq7693001DBTR Yes

bq7693002DBT bq7693002DBTR

3.3

bq7693003DBT bq7693003DBTR Yes

bq7693006DBT bq7693006DBTR 0x18 No

bq7693007DBT bq7693007DBTR Yes

bq7694000DBT bq7694000DBTR

9–15 0x08

2.5 No

44-TSSOP (DBT)

bq7694001DBT bq7694001DBTR Yes

bq7694002DBT bq7694002DBTR

3.3

bq7694003DBT bq7694003DBTR Yes

bq7694006DBT bq7694006DBTR 0x18 No

Texas Instruments pre-configures the bq769x0 devices for a specific I2C address, LDO voltage, and more.

These settings are permanently stored in EEPROM and cannot be further modified.

Contact Texas Instruments for other options not listed above, as well as any options noted as “Product

Preview only.”

VC10

VC9

VC8

VC7

VC6

VC5

VC4

VC3

VC2

VC1

SRN

SRP

VC15

VC14

VC13

VC12

VC11

VC10 x

TS3

VC0

VC5x

VSS

SCL

SDA

CHG

DSG

CAP1

TS1

CAP3

CAP2

REGSRC

TS2

REGOUT

VC5B

22 NC

BAT

VC10 B

bq76940

44-TSSOP

ALERT

15 16

VC10

VC9

VC8

VC7

VC6

VC5

VC4

VC3

VC2

VC1

VC0

VC5B

SRN

SRP

bq76930

30-TSSOP

ALERT

BAT

VC5x

VSS

SCL

SDA

CHG

DSG

CAP1

TS1

CAP2

REGSRC

TS2

REGOUT

SRN

SRP

10 11

VC5

VC4

VC3

VC2

VC1

VC0

bq76920

20-TSSOP

ALERT

BAT

VSS

SCL

SDA

CHG

DSG

CAP 1

TS1

REGSRC

REGOUT

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

5 Pin Configuration and Functions

5.1 Versions

Figure 5-1. Pin Versions

bq76920: 3–5 Series Cells (20-TSSOP)

• 6.5 mm x 4.4 mm x 1.2 mm

bq76930: 6–10 Series Cells (30-TSSOP)

• 7.8 mm x 4.4 mm x 1.2 mm

bq76940: 9–15 Series Cells (44-TSSOP)

• 11.3 mm x 4.4 mm x 1.2 mm

SRN

SRP

10 11

VC5

VC4

VC3

VC2

VC1

VC0

bq76920

20-TSSOP

ALERT

BAT

VSS

SCL

SDA

CHG

DSG

CAP 1

TS1

REGSRC

REGOUT

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

5.2 bq76920 Pin Diagram

5.2.1 bq76920 Pin Map

(1) If not used, pull down to VSS with a 10-kΩnominal resistor.

bq76920 Pin Functions

PIN NAME TYPE DESCRIPTION

1 DSG O Discharge FET driver

2 CHG O Charge FET driver

3 VSS — Chip VSS

4 SDA I/O I2C communication to the host controller

5 SCL I I2C communication to the host controller

6 TS1 I Thermistor #1 positive terminal(1)

7 CAP1 O Capacitor to VSS

8 REGOUT P Output LDO

9 REGSRC I Input source for output LDO

10 BAT P Battery (top-most) terminal

11 NC — No connect

12 VC5 I Sense voltage for 5th cell positive terminal

13 VC4 I Sense voltage for 4th cell positive terminal

14 VC3 I Sense voltage for 3rd cell positive terminal

15 VC2 I Sense voltage for 2nd cell positive terminal

16 VC1 I Sense voltage for 1st cell positive terminal

17 VC0 I Sense voltage for 1st cell negative terminal

18 SRP I Negative current sense (nearest VSS)

19 SRN I Positive current sense

20 ALERT I/O Alert output and override input

15 16

VC10

VC9

VC8

VC7

VC6

VC5

VC4

VC3

VC2

VC1

VC0

VC5B

SRN

SRP

bq76930

30-TSSOP

ALERT

BAT

VC5x

VSS

SCL

SDA

CHG

DSG

CAP1

TS1

CAP2

REGSRC

TS2

REGOUT

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

5.3 bq76930 Pin Diagram

5.3.1 bq76930 Pin Map

(1) If not used, pull down to group ground reference (VSS for TS1 and VC5X for TS2) with a 10-kΩ

nominal resistor.

bq76930 Pin Functions

PIN NAME TYPE DESCRIPTION

1 DSG O Discharge FET driver

2 CHG O Charge FET driver

3 VSS — Chip VSS

4 SDA I/O I2C communication to the host controller

5 SCL I I2C communication to the host controller

6 TS1 I Thermistor #1 positive terminal(1)

7 CAP1 O Capacitor to VSS

8 REGOUT P Output LDO

9 REGSRC I Input source for output LDO

10 VC5X P Thermistor #2 negative terminal

11 NC — No connect (short to CAP2)

12 NC — No connect (short to CAP2)

13 TS2 I Thermistor #2 positive terminal(1)

14 CAP2 O Capacitor to VC5X

15 BAT P Battery (top-most) terminal

16 VC10 I Sense voltage for 10th cell positive terminal

17 VC9 I Sense voltage for 9th cell positive terminal

18 VC8 I Sense voltage for 8th cell positive terminal

19 VC7 I Sense voltage for 7th cell positive terminal

20 VC6 I Sense voltage for 6th cell positive terminal

21 VC5B I Sense voltage for 6th cell negative terminal

22 VC5 I Sense voltage for 5th cell positive terminal

23 VC4 I Sense voltage for 4th cell positive terminal

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

bq76930 Pin Functions (continued)

PIN NAME TYPE DESCRIPTION

24 VC3 I Sense voltage for 3rd cell positive terminal

25 VC2 I Sense voltage for 2nd cell positive terminal

26 VC1 I Sense voltage for 1st cell positive terminal

27 VC0 I Sense voltage for 1st cell negative terminal

28 SRP I Negative current sense (nearest VSS)

29 SRN I Positive current sense

30 ALERT I/O Alert output and override input

VC10

VC9

VC8

VC7

VC6

VC5

VC4

VC3

VC2

VC1

SRN

SRP

VC15

VC14

VC13

VC12

VC11

VC10x

TS3

VC0

VC5x

VSS

SCL

SDA

CHG

DSG

CAP1

TS1

CAP3

CAP2

REGSRC

TS2

REGOUT

VC5B

22 NC

BAT

VC10B

bq76940

44-TSSOP

ALERT

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

5.4 bq76940 Pin Diagram

5.4.1 bq76940 Pin Map

(1) If not used, pull down to group ground reference (VSS for TS1, VC5X for TS2, and VC10X for TS3)

with a 10-kΩnominal resistor.

bq76940 Pin Functions

PIN NAME TYPE DESCRIPTION

1 DSG O Discharge FET driver

2 CHG O Charge FET driver

3 VSS — Chip VSS

4 SDA I/O I2C communication to the host controller

5 SCL I I2C communication to the host controller

6 TS1 I Thermistor #1 positive terminal(1)

7 CAP1 O Capacitor to VSS

8 REGOUT P Output LDO

9 REGSRC I Input source for output LDO

10 VC5X P Thermistor #2 negative terminal

11 NC — No connect (short to CAP2)

12 NC — No connect (short to CAP2)

13 TS2 I Thermistor #2 positive terminal(1)

14 CAP2 O Capacitor to VC5X

15 VC10X P Thermistor #3 negative terminal

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

bq76940 Pin Functions (continued)

PIN NAME TYPE DESCRIPTION

16 NC — No connect (short to CAP3)

17 NC — No connect (short to CAP3)

18 TS3 I Thermistor #3 positive terminal(1)

19 CAP3 O Capacitor to VC10X

20 BAT P Battery (top-most) terminal

21 NC — No connect

22 NC — No connect

23 NC — No connect

24 VC15 I Sense voltage for 15th cell positive terminal

25 VC14 I Sense voltage for 14th cell positive terminal

26 VC13 I Sense voltage for 13th cell positive terminal

27 VC12 I Sense voltage for 12th cell positive terminal

28 VC11 I Sense voltage for 11th cell positive terminal

29 VC10B I Sense voltage for 11th cell negative terminal

30 VC10 I Sense voltage for 10th cell positive terminal

31 VC9 I Sense voltage for 9th cell positive terminal

32 VC8 I Sense voltage for 8th cell positive terminal

33 VC7 I Sense voltage for 7th cell positive terminal

34 VC6 I Sense voltage for 6th cell positive terminal

35 VC5B I Sense voltage for 6th cell negative terminal

36 VC5 I Sense voltage for 5th cell positive terminal

37 VC4 I Sense voltage for 4th cell positive terminal

38 VC3 I Sense voltage for 3rd cell positive terminal

39 VC2 I Sense voltage for 2nd cell positive terminal

40 VC1 I Sense voltage for 1st cell positive terminal

41 VC0 I Sense voltage for 1st cell negative terminal

42 SRP I Negative current sense (nearest VSS)

43 SRN I Positive current sense

44 ALERT I/O Alert output and override input

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

(1) The Absolute Maximum Ratings for (TS1–VSS) apply after the device completes POR and should be observed after tBOOTREADY

(10 ms), following the application of the boot signal on TS1. Prior to completion of POR, TS1 should not exceed 5 V.

6 Specifications

6.1 Absolute Maximum Ratings

Over-operating free-air temperature range (unless otherwise noted) MIN MAX UNIT

VBAT Supply voltage (BAT–VSS) bq76920 –0.3 36 V(BAT–VC5x), (VC5x–VSS) bq76930

(BAT–VC10x), (VC10x–VC5x), (VC5x–VSS) bq76940

VIInput voltage

(VCn–VSS) where n = 1..5 bq76920

–0.3 (n × 7.2) V

(VCn–VSS) where n = 1..5, (VCn-VC5x) where n =

6..10 bq76930

(VCn–VSS) where n = 1..5, (VCn–VC5x) where n =

6..10, (VCn–VC10x) where n = 11..15 bq76940

Cell input pins, differential (VCn–VCn–1) where n = 1..15/10/5

(bq76940/bq76930/bq76920, respectively) –0.3 9 V

SRN, SRP, SCL, SDA

–0.3 3.6 V

(VC0–VSS), (CAP1–VSS), (TS1–VSS)(1) bq76920

(VC0–VSS), (VC5b–VC5x), (CAP2–VC5x),

(CAP1–VSS), (TS2–VC5x), (TS1–VSS)(1) bq76930

(VC0–VSS), (VC5b–VC5x), (VC10b–VC10x),

(CAP3–VC10x), (CAP2–VC5x), (CAP1–VSS),

(TS3–VC10x), (TS2–VC5x), (TS1–VSS)(1) bq76940

REGSRC –0.3 36

VOOutput voltage REGOUT, ALERT –0.3 3.6 VDSG –0.3 20

CHG –0.3 VCHGCLAMP

ICB Cell balancing current (per cell) bq76920 70 mA

bq76930,

bq76940 5 mA

IDSG Discharge pin input current when disabled (measured into terminal) 7 mA

TSTG Storage temperature –65 150 °C

Lead temperature (soldering, 10 s) 300

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

6.2 ESD Ratings

VALUE UNIT

V(ESD) Electrostatic

discharge Human body model (HBM) ESD stress voltage(1) ±2 kV

Charged device model (CDM) ESD stress voltage(2) ±500 V

6.3 Recommended Operating Conditions

Over-operating free-air temperature range (unless otherwise noted). See Section 8.1.1 for more information on cell

configurations. All voltages are relative to VSS, except "Cell input differential." MIN TYP MAX UNIT

VBAT Supply voltage

(BAT–VSS) bq76920

6 25 V

(BAT–VC5x), (VC5x–VSS) bq76930

(BAT–VC10x), (VC10x–VC5x),

(VC5x–VSS) bq76940

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Recommended Operating Conditions (continued)

Over-operating free-air temperature range (unless otherwise noted). See Section 8.1.1 for more information on cell

configurations. All voltages are relative to VSS, except "Cell input differential." MIN TYP MAX UNIT

VIN Input voltage

Cell input pins, differential (VCn–VCn–1) where n =

1..15/10/5 (bq76940/bq76930/bq76920, respectively),

in-use cells only 2 5 V

(VCn–VSS) where n = 1..5 bq76920

0 5 × n V

(VCn–VSS) where n = 1..5,

(VCn–VC5x) where n = 6..10 bq76930

(VCn–VSS) where n = 1..5,

(VCn–VC5x) where n = 6..10,

(VCn–VC10x) where n = 11..15 bq76940

SRP

–10 10 mV

(VC0–VSS) bq76920

(VC0–VSS), (VC5b–VC5x) bq76930

(VC0–VSS), (VC5b–VC5x),

(VC10b–VC10x) bq76940

SRN –200 200 mV

SCL, SDA

0 3.6 V

(TS1–VSS) bq76920

(TS1–VSS), (TS2–VC5x) bq76930

(TS1–VSS), (TS2–VC5x),

(TS3–VC10x) bq76940

REGSRC 6 25

VOUT Output voltage

CHG, DSG 0 16 V

REGOUT, ALERT

0 3.6 V

(CAP1–VSS) bq76920

(CAP1–VSS), (CAP2–VC5x) bq76930

(CAP1–VSS), (CAP2–VC5x),

(CAP3–VC10x) bq76940

ICB Cell balancing

current (internal, per

cell)

bq76920 0 50 mA

bq76930, bq76940 0 5 mA

RCExternal cell input

resistance bq76920 40 100 1K Ω

bq76930, bq76940 500 1K 1K Ω

CCExternal cell input capacitance 0.1 1 10 µF

RfExternal supply filter resistance 40 100 1K Ω

CfExternal supply filter capacitance 1 10 40 µF

RFILT Sense resistor filter resistance 100 1K Ω

RALERT ALERT pin to VSS resistor 1M Ω

CLREGOUT loading capacitance 1 4.7 µF

CCAP REGSRC, CAP1, CAP2, and CAP3 output capacitance 1 µF

RTS External thermistor nominal resistance (103AT) at 25ºC 10K Ω

TOPR Operating free-air temperature –40 85 °C

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application

report (SPRA953).

(2) The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as

specified in JESD51-7, in an environment described in JESD51-2a.

(3) The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific JEDEC-

standard test exists, but a close description can be found in the ANSI SEMI standard G30-88.

(4) The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB

temperature, as described in JESD51-8.

(5) The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted

from the simulation data for obtaining RθJA, using a procedure described in JESD51-2a (sections 6 and 7).

(6) The junction-to-board characterization parameter, ψJB, estimates the junction temperature of a device in a real system and is extracted

from the simulation data for obtaining RθJA, using a procedure described in JESD51-2a (sections 6 and 7).

(7) The junction-to-case (bottom) thermal resistance is obtained by simulating a cold plate test on the exposed (power) pad. No specific

JEDEC standard test exists, but a close description can be found in the ANSI SEMI standard G30-88.

Spacer

6.4 Thermal Information

Over-operating free-air temperature range (unless otherwise noted)

THERMAL METRIC(1) TSSOP UNIT

bq76920xy

20 PINS (PW) bq76930xy

30 PINS (DBT) bq76940xy

44 PINS (DBT)

RθJA, High K Junction-to-ambient thermal resistance(2) 93.7 86.5 70.1 °C/W

RθJC(top) Junction-to-case(top) thermal resistance(3) 28.7 19.4 17.5 °C/W

RθJB Junction-to-board thermal resistance(4) 44.6 41.3 33.9 °C/W

ψJT Junction-to-top characterization parameter(5) 1.3 0.5 0.5 °C/W

ψJB Junction-to-board characterization parameter(6) 44.1 40.6 33.4 °C/W

RθJC(bottom) Junction-to-case(bottom) thermal resistance(7) n/a n/a n/a °C/W

6.5 Electrical Characteristics

Typical conditions are measured at 25ºC with nominal BAT voltages of 18 V (bq76920), 36 V (bq76930), or 48 V (bq76940)

with VCELL = 4 V. Min and max values include full recommended operating condition temperature range from –40ºC to +85ºC.

Certain characteristics may be shown at different voltage or temperature ranges, as clarified in the Test Condition sections.

PARAMETER TEST CONDITION MIN TYP MAX UNIT

SUPPLY CURRENTS

IDD

NORMAL mode: ADC off,

CC off

Sum of ICC_BAT and ICC_REGSRC

currents

40 60

µA

NORMAL mode: ADC on,

CC off 60 90

NORMAL mode: ADC off,

CC on 110 165

NORMAL mode: ADC on,

CC on 130 195

ICC_BAT NORMAL mode: ADC off Into BAT pin 30 45

NORMAL mode: ADC on 50 75

ICC_REGSRC NORMAL mode: CC off Into REGSRC pin 10 15

NORMAL mode: CC on 80 120

ISHIP SHIP/SHUTDOWN mode Device in full shutdown, only

VSTUP/BG and BOOT detector on 0.6 1.8

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Electrical Characteristics (continued)

Typical conditions are measured at 25ºC with nominal BAT voltages of 18 V (bq76920), 36 V (bq76930), or 48 V (bq76940)

with VCELL = 4 V. Min and max values include full recommended operating condition temperature range from –40ºC to +85ºC.

Certain characteristics may be shown at different voltage or temperature ranges, as clarified in the Test Condition sections.

PARAMETER TEST CONDITION MIN TYP MAX UNIT

(1) Measured at BAT pin, rising.

LEAKAGE AND OFFSET CURRENTS

dINOM NORMAL mode supply

current offset Measured into VC5x (bq76930,

bq76940) and VC10x (bq76940)

–5 ±2.5 5

µA

dISHIP SHIP mode supply

current offset –1.0 ±0.1 1.0

dIALERT Supply current when

ALERT active Measured into VC5x (bq76930,

bq76940) or added to BAT (bq76920) 15 25

dICELL Cell measurement input

current

Measured into VC0–VC15 except VC5,

VC10, VC15 –0.3 ±0.1 0.3

Measured into VC5, VC10, VC15 0.5

ILKG Terminal input leakage 1

INTERNAL POWER CONTROL (STARTUP and SHUTDOWN)

VPORA Analog POR threshold See Note(1) 4 5 V

VSHUT Shutdown voltage See Note(1) 3.6 V

tI2CSTARTUP Time delay after boot

signal on TS1 before I2C

communications allowed Delay after boot sequence when I2C

communication is allowed 1 ms

tBOOTREADY Device boot startup delay Delay after boot signal when device has

completed full boot-up sequence 10 ms

TSHUTD Thermal shutdown

voltage 100 150 °C

MEASUREMENT SCHEDULE

tVCELL Cell voltage measurement

interval bq76920, bq76930, bq76940 250

tINDCELL Individual cell

measurement time Per cell, balancing off 50

Per cell, balancing on 12.5

tCB_RELAX Cell balancing relaxation

time before cell voltage

measured 12.5

tTEMP_DEC Temperature

measurement decimation

time Measurement duration for temperature

reading 12.5

tBAT Pack voltage calculation

interval 250

tTEMP Temperature

measurement interval Period of measurement of either

TS1/TS2/TS3 or internal die temp 2 s

14-BIT ADC FOR CELL VOLTAGE AND TEMPERATURE MEASUREMENT

ADCRANGE ADC measurement

recommend operation

range

VCELL measurements 2 5 V

TS/Temp measurements 0.3 3 V

ADCLSB ADC LSB value 382 µV

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Electrical Characteristics (continued)

Typical conditions are measured at 25ºC with nominal BAT voltages of 18 V (bq76920), 36 V (bq76930), or 48 V (bq76940)

with VCELL = 4 V. Min and max values include full recommended operating condition temperature range from –40ºC to +85ºC.

Certain characteristics may be shown at different voltage or temperature ranges, as clarified in the Test Condition sections.

PARAMETER TEST CONDITION MIN TYP MAX UNIT

ADC

ADC cell voltage

accuracy at 25°C

VCELL = 3.6 – 4.3 V ±10

VCELL = 3.2 – 4.6 V ±15

VCELL = 2.0 – 5.0 V ±25

ADC cell voltage

accuracy 0°C to 60°C

VCELL = 3.6 – 4.3 V ±20

VCELL = 3.2 – 4.6 V ±25

VCELL = 2.0 – 5.0 V ±35

ADC cell voltage

accuracy –40°C to 85°C

VCELL = 3.6 – 4.3 V –40 40

VCELL = 3.2 – 4.6 V –40 40

VCELL = 2.0 – 5.0 V –50 50

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Electrical Characteristics (continued)

Typical conditions are measured at 25ºC with nominal BAT voltages of 18 V (bq76920), 36 V (bq76930), or 48 V (bq76940)

with VCELL = 4 V. Min and max values include full recommended operating condition temperature range from –40ºC to +85ºC.

Certain characteristics may be shown at different voltage or temperature ranges, as clarified in the Test Condition sections.

PARAMETER TEST CONDITION MIN TYP MAX UNIT

(2) Values indicate nominal thresholds only. For Min and Max variation, apply OCOFFSET and OCSCALERR.

(3) Values indicate nominal thresholds only. For Min and Max variation, apply tPROTACC.

16-BIT CC FOR PACK CURRENT MEASUREMENT

CCRANGE CC input voltage range –200 200 mV

CCFSR CC full scale range –270 270 mV

CCLSB CC LSB value CC running constantly 8.44 µV

tCCREAD Conversion time Single conversion 250 ms

CCINL Integral nonlinearity 16-bit, best fit over input voltage range

± 200 mV ± 2 ± 40 LSB

CCOFFSET Offset error ± 1 ± 3 LSB

CCGAIN Gain error Over input voltage range ± 0.5% ± 1.5% FSR

CCGAINDRIFT Gain error drift Over input voltage range 150 PPM / °C

CCRIN Effective input resistance 2.5 MΩ

THERMISTOR BIAS

RTS Pull-up resistance TA= 25°C 9.85 10 10.15 kΩ

RTSDRIFT Pull-up resistance across

temp TA= –40°C to 85°C 9.7 10.3 kΩ

DIETEMP

VDIETEMP25 Die temperature voltage TA= 25°C 1.20 V

VDIETEMPDRIFT Die temperature voltage

drift –4.2 mV/°C

INTEGRATED HARDWARE PROTECTIONS

OVRANGE OV threshold range 0x2008 0x2FF8 ADC

UVRANGE UV threshold range 0x1000 0x1FF0 ADC

OVUVSTEP OV and UV threshold step

size 16 LSB

UVMINQUAL UV minimum value to

qualify Below UVMINQUAL, cell is shorted

(unused) 0x0518 ADC

OVDELAY OV delay timer options

OV delay = 1 s 0.7 1 1.75

OV delay = 2 s 1.6 2 2.75

OV delay = 4 s 3.5 4 5

OV delay = 8 s 7 8 10

UVDELAY UV delay timer options

UV delay = 1 s 0.7 1 1.75

UV delay = 4 s 3.5 4 5

UV delay = 8 s 7 8 10

UV delay = 16 s 14 16 20

OCDRANGE OCD threshold options Measured across (SRP–SRN)(2) 8 100 mV

OCDSTEP OCD threshold step size RSNS = 0 2.78 mV

RSNS = 1 5.56 mV

OCDDELAY OCD delay options See Note (3) 8 1280 ms

SCDRANGE SCD threshold options Measured across (SRP–SRN)(2) 22 200 mV

SCDSTEP SCD threshold step size RSNS = 0 11.1 mV

RSNS = 1 22.2 mV

SCDDELAY SCD delay options

35 70 105 µs

50 100 150 µs

140 200 260 µs

280 400 520 µs

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Electrical Characteristics (continued)

Typical conditions are measured at 25ºC with nominal BAT voltages of 18 V (bq76920), 36 V (bq76930), or 48 V (bq76940)

with VCELL = 4 V. Min and max values include full recommended operating condition temperature range from –40ºC to +85ºC.

Certain characteristics may be shown at different voltage or temperature ranges, as clarified in the Test Condition sections.

PARAMETER TEST CONDITION MIN TYP MAX UNIT

(4) MIN specifies the threshold below which the device will never register that an external alert has occurred. MAX specifies the minimum

threshold above which the device will always register that an external alert has occurred.

tPROTACC Delay accuracy for OCD –20% 20%

OCOFFSET OCD and SCD voltage

offset –2.5 2.5 mV

OCSCALEERR OCD and SCD scale

accuracy –10% 10%

CHARGE AND DISCHARGE DRIVERS

VFETON CHG and DSG on

REGSRC ≥12 V with load resistance of

10 MΩ10 12 14 V

REGSRC < 12 V with load resistance of

10 MΩREGSRC

–2 REGSRC

–1 REGSRC V

tFET_ON CHG and DSG ON rise

time CHG/DSG driving an equivalent load

capacitance of 10 nF, measured from

10% to 90% of VFETON 200 250 µs

tDSG_OFF DSG pull-down OFF fall

time DSG driving an equivalent load

capacitance of 10 nF, measured from

90% to 10% 60 90 µs

RCHG_OFF CHG pull-down OFF

resistance to VSS When CHG disabled, CHG held at 12 V 750 1000 1250 kΩ

RDSG_OFF DSG pull-down OFF

resistance to VSS When DSG disabled, DSG held at 12 V 1.75 2.50 4.25 kΩ

VLOAD_DETECT Load detection threshold 0.4 0.7 1.0 V

VCHG_CLAMP CHG clamp voltage If the CHG pin externally pulled high

(through PACK–, if load applied),

500 µA max sink current into CHG pin.

With CHG_ON bit cleared. 18 20 22 V

ALERT PIN

VALERT_OH ALERT output voltage

high IOL = 1 mA REGOUT x

0.75 V

VALERT_OL ALERT output voltage low Unloaded REGOUT

x 0.25 V

VALERT_IH ALERT input high ALERT externally forced high when

internally driven low. See note (4).1 1.5 V

RALERT_PD ALERT pin weak

pulldown resistance when

driven low Measured into ALERT pin with ALERT

= REGOUT 0.8 2.5 8 MΩ

CELL BALANCING DRIVER

RDSFET Internal cell balancing

driver resistance VCELL = 3.6 V 1 5 10 Ω

XBAL Cell balancing duty cycle

when enabled Every 250 ms 70%

EXTERNAL REGULATOR

VEXTLDO External LDO voltage

options Nominal values, TI factory programmed,

unloaded, across temp 2.45 2.50 2.55 V

3.20 3.30 3.40 V

VEXTLDO_LN Line regulation REGSRC pin stepped from 6 to 25 V,

with 10 mA load, in 100 µs 100 mV

VEXTLDO_LD Load regulation IREGOUT = 0 mA to 10 mA –4% 4%

VEXTLDO_DC External LDO minimum

voltage under DC load

REGOUT = 10 mA DC, 2.5-V version 2.4 V

REGOUT = 20 mA DC, 2.5-V version 2.3 V

REGOUT = 10 mA DC, 3.3-V version 3.15 V

REGOUT = 20 mA DC, 3.3-V version 3.05 V

SCL

SDA

SCL

SDA

SCL

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Electrical Characteristics (continued)

Typical conditions are measured at 25ºC with nominal BAT voltages of 18 V (bq76920), 36 V (bq76930), or 48 V (bq76940)

with VCELL = 4 V. Min and max values include full recommended operating condition temperature range from –40ºC to +85ºC.

Certain characteristics may be shown at different voltage or temperature ranges, as clarified in the Test Condition sections.

PARAMETER TEST CONDITION MIN TYP MAX UNIT

IEXTLDO_LIMIT External LDO current limit REGOUT = 0 V 30 38 45 mA

BOOT DETECTOR

VBOOT Boot threshold voltage Measured at TS1 pin with device in

SHIP mode. Below MIN, device will not

boot up. Above MAX, device will be

guaranteed to boot up. 300 1000 mV

tBOOT_max Boot threshold application

time Measured at TS1 pin. Below MIN,

device will not boot up. Above MAX,

device will be guaranteed to boot up. 10 2000 µs

6.6 Timing Requirements

I2C COMPATIBLE INTERFACE MIN TYP MAX UNIT

VIL Input Low Logic Threshold REGOUT x

0.25 V

VIH Input High Logic Threshold REGOUT x

0.75 V

VOL Output Low Logic Drive 0.20 V

tfSCL, SDA Fall Time 0.40

VOH Output High Logic Drive (Not applicable due to open-drain outputs) N/A N/A V

tHIGH SCL Pulse Width High 4.0 µs

tLOW SCL Pulse Width Low 4.7 µs

tSU;STA Setup time for START condition 4.7 µs

tHD;STA START condition hold time after which first clock pulse is generated 4.0 µs

tSU;DAT Data setup time 250 ns

tHD;DAT Data hold time 0 µs

tSU;STO Setup time for STOP condition 4.0 µs

tBUF Time the bus must be free before new transmission can start 4.7 µs

tVD;DAT Clock Low to Data Out Valid 900 ns

tHD;DAT Data Out Hold Time After Clock Low 0 ns

fSCL Clock Frequency 0 100 kHz

Figure 6-1. I2C Timing

±0.02

±0.01

0.00

0.01

±40 ±15 10 35 60 85

OV Detection Error (V)

Temperature (ƒC)

C004

±0.7

±0.6

±0.5

±0.4

±0.3

±0.2

±0.1

0.0

±40 ±15 10 35 60 85

Gain Error (%FSR)

Temperature (ƒC)

C003

±1.6

±1.4

±1.2

±1.0

±0.8

±0.6

±0.4

±0.2

0.0

±40 ±15 10 35 60 85

Offset (uV)

Temperature (ƒC)

C002

±5

±40 ±15 10 35 60 85

Gain Error (PPM)

Temperature (ƒC)

C005

±0.004

±0.002

0.000

0.002

0.004

0.006

0.008

0.010

0.012

0.014

0.016

0.018

0.020

2.00 2.30 2.60 2.90 3.20 3.50 3.80 4.10 4.40 4.70 5.00

VCx Error (mV)

VCx Input (V)

VC1 Error

VC2 Error

VC3 Error

VC4 Error

VC5 Error

C001

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

6.7 Typical Characteristics

Figure 6-2. bq76930 VCx Error Across Input Range at 25°C with

VIN at 3.6 V Figure 6-3. Coulomb Counter Gain Error Temperature Drift

(from –0.2 V to 0.2 V)

Figure 6-4. Coulomb Counter Gain Error

(from –0.2 V to 0.2 V) Figure 6-5. Coulomb Counter Offset

Figure 6-6. OV Protection Detection Error (0xFF Setting)

BAT

CHG

VSS

Cell Balance

Drivers/FETs

EEPROM

Internal 3.3-V

LDO

DSG

SRNSRP

SDA

SCL

REG

SRC

REG

OUT

External

2.5/3.3-V LDO

I2C

Bandgap

IBIAS

VSTUP/POR

14-bit ADC

Modulator

V2I

OCD

comp

Digital core

BOOT

CAP

To POR

BOOT

256 kHz

ALERT

FET

DRIVER and

LOAD

DETECT

CC VREF

16-bit ACC

Modulator

Die temp

VCx Inputs

SCD

comp

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

7 Detailed Description

7.1 Overview

In the bq769x0 family of analog front-end (AFE) devices, the bq76920 device supports up to 5-series cells,

the bq76930 device supports up to 10-series cells, and the bq76940 device supports up to 15-series cells.

Through I2C, a host controller can use the bq769x0 to implement battery pack management functions,

such as monitoring (cell voltages, pack current, pack temperatures), protection (controlling

charge/discharge FETs), and balancing. Integrated A/D converters enable a purely digital readout of

critical system parameters including cell voltages and internal or external temperature, with calibration

handled in TI’s manufacturing process. For an additional degree of pack reliability, the bq769x0 includes

hardware protections for voltage (OV, UV) and current (OCD, SCD).

The bq769x0 provides two low-side FET drivers, charge (CHG) and discharge (DSG), which may be used

to directly manipulate low-side power NCH FETs, or as signals that control an external circuit that enables

high-side PCH or NCH FETs. A dedicated ALERT input/output pin serves as an interrupt signal to the host

microcontroller, quickly informing the microcontroller of an updated status in the AFE. This may include a

fault event or that a coulomb counter sample is available for reading. An available ALERT pin may also be

driven externally by a secondary protector to provide a redundant means of disabling the CHG and DSG

signals and higher system visibility.

7.2 Functional Block Diagram

Figure 7-1. Functional Block Diagram

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

7.3 Feature Description

7.3.1 Subsystems

bq769x0 consists of three major subsystems: Measurement, Protection, and Control. These work together

to ensure that the fundamental battery pack parameters—voltage, current and temperature—are

accurately captured and easily available to a host controller, while ensuring a baseline or secondary level

of hardware protection in the event that a host controller is unable or unavailable to manage certain fault

conditions.

NOTE

The bq769x0 is intended to serve as an analog front-end (AFE) as part of a chipset system

solution: A companion microcontroller is required to oversee and control this AFE.

• The Measurement subsystem’s core responsibility is to digitize the cell voltages, pack current

(integrated into a passed charge calculation), external thermistor temperature, and internal die

temperature. It also performs an automatic calculation of the total battery stack voltage, by simply

adding up all measured cell voltages.

• The Protection subsystem provides a baseline or secondary level of hardware protections to better

support a battery pack’s FMEA requirements in the event of a loss of host control or simply if a host is

unable to respond to a certain fault event in time. Integrated protections include pack-level faults such

as OV, UV, OCD, SCD, detection of an external secondary protector fault, and internal logic

“watchdog”-style device fault (XREADY). Protection events will trigger toggling of the ALERT pin, as

well as automatic disabling of the DSG or CHG FET driver (depending on the fault). Recovery from a

fault event must be handled by the host microcontroller.

• The Control subsystem implements a suite of useful pack features, including direct low-side NCH FET

drivers, cell balancing drivers, the ALERT digital output, an external LDO and more.

The following sections describe each subsystem in greater detail, as well as explaining the various power

states that are available.

7.3.1.1 Measurement Subsystem Overview

The monitoring subsystem ensures that all cell voltages, temperatures, and pack current may be easily

measured by the host. All ADCs are trimmed by TI.

ADC and CC data are always returned as atomic values if both high and low registers are read in the

same transaction (using address auto-increment).

7.3.1.1.1 Data Transfer to the Host Controller

The bq769x0 has a fully digital interface: All information is transferred through I2C, simply by reading

and/or writing to the appropriate register(s) storing the relevant data. Block reads and writes, buffered by

an 8-bit CRC code per byte, ensure a fast and robust transmission of data.

7.3.1.1.2 14-Bit ADC

Each bq769x0 device measures cell voltages and temperatures using a 14-bit ADC. This ADC measures

all differential cell voltages, thermistors and/or die temperature with a nominal full-scale unsigned range of

0–6.275 V and LSB of 382 µV.

To enable the ADC, the [ADC_EN] bit in the SYS_CTRL1 register must be set. This bit is set automatically

whenever the device enters NORMAL mode. When enabled, the ADC ensures that the integrated OV and

UV protections are functional.

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

For each contiguous set of five cells (VC1 to VC5, VC6 to VC10), when no cells in that particular set are

being balanced, each cell is measured over a 50-ms decimation window and a complete update is

available every 250 ms. In the bq76930 and bq76940, every set of five cells above the primary five cells is

measured in parallel. The 50-ms decimation greatly assists with removing the aliasing effects present in a

noisy motor environment.

When any cells in a contiguous set of 5 cells are being balanced, those affected cells are measured in a

reduced 12.5-ms decimation period, to allow the cell balancing to function properly without affecting the

integrated OV and UV protections. Since cell balancing is typically only performed during pack charge or

idle periods, the shortened decimation periods should not impact accuracy as the system noise during

these times is greatly reduced. This reduced decimation period is only applied to sets where one of the

cells is being balanced. The following summarizes this for the bq76920–bq76940 devices:

• VC1 to VC5 measurements are each taken in a 50-ms decimation period when all bits in CELLBAL1

• VC6 to VC10 measurements are each taken in a 50-ms decimation period when all bits in CELLBAL2

• VC11 to VC15 measurements are each taken in a 50-ms decimation period when all bits in CELLBAL3

• Total update interval is 250 ms.

Each differential cell input is factory-trimmed for gain or offset, such that the resulting reading through I2C

is always consistent from part-to-part and requires no additional calibration or correction factor application.

The ADC is required to be enabled in order for the integrated OV and UV protections to be operating.

The following shows how to convert the 14-bit ADC reading into an analog voltage. Each device is factory

calibrated, with a GAIN and OFFSET stored into EEPROM.

The ADC transfer function is a linear equation defined as follows:

V(cell) = GAIN x ADC(cell) + OFFSET (1)

GAIN is stored in units of µV/LSB, while OFFSET is stored in mV units.

Some example cell voltage calculations are provided in the table below. For illustration purposes, the

example uses a hypothetical GAIN of 380 µV/LSB (ADCGAIN<4:0> = 0x0F) and OFFSET of 30 mV

(ADCOFFSET<7:0> = 0x1E).

14-Bit ADC Result ADC Result in Decimal GAIN (µV/LSB) OFFSET (mV) Cell Voltage (mV)

0x1800 6144 380 30 2365

0x1F10 7952 380 30 3052

NOTE

When entering NORMAL mode from SHIP mode, please allow for the following times before

reading out initial cell voltage data:

bq76920: 250 ms

bq76930: 400 ms

bq76940: 800 ms

Battery cell stack

Gen.purpose output

A/D input

Host microcontroller

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

7.3.1.1.2.1 Optional Real-time Calibration Using the Host Microcontroller

The performance of the cell voltage values measured by the 14-bit ADC has a factory-calibrated accuracy,

as follows:

• +/– 10 mV TYP, +/– 40 mV MIN and MAX from 3.6 to 4.3 V,

• +/– 15 mV TYP, +/– 40 mV MIN and MAX from 3.2 to 4.6 V, and

• +/– 50 mV MIN and MAX from 2.0 to 5.0 V

While this is suitable for the majority of pack protection and basic monitoring applications the bq769x0

AFE family is intended to support, certain systems may require a higher accuracy performance.

To achieve this, use an available ADC channel and general purpose output terminal on the host

microcontroller paired with the bq769x0. A simple external circuit consisting of two precision resistors and

a small-signal FET is activated by the host microcontroller to determine the total stack voltage, VSTACK.

This is then compared against the sum of the individual cell voltages as measured by the internal ADC of

the bq769x0. The resulting transfer function coefficient, GAIN2, is simply applied to each cell voltage ADC

value for improved accuracy.

Figure 7-2. External Real-Time Calibration Circuit to Host Microcontroller

The process is as follows:

1. Periodically measure VSTACK.

(a) VSTACK = VAD × (R1 + R2) / R1

2. Read out all VCELL ADC readings from the bq769x0 and apply the standard GAIN and OFFSET values

stored in the bq769x0.

(a) V(1) = GAIN x ADC1+ OFFSET, V(2) = GAIN x ADC2+ OFFSET, and so on

3. Sum up all VCELL values, VSUM.

(a) VSUM = V(1) + V(2) + V(3) …

4. Calculate GAIN2.

(a) GAIN2= VSTACK / VSUM

As a general recommendation, a new GAIN2function should be generated when the cell voltages increase

or decrease by more than 100 mV. With GAIN2, each cell voltage calculation becomes:

V(cell) = GAIN2× (GAIN x ADC(cell) + OFFSET) (2)

For systems that do not require this additional in-use calibration function, GAIN2is simply “1”.

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

7.3.1.1.3 16-Bit CC

A 16-bit integrating ADC, commonly referred to as the coulomb counter (CC), provides measurements of

accumulated charge across the current sense resistor. The integration period for this reading is 250 ms.

The CC may be operated in one of two modes: ALWAYS ON and 1-SHOT.

• In ALWAYS ON mode, the CC runs at 100%, gathering a fresh reading every 250 ms. The conclusion

of each reading sets the CC_READY bit, which toggles the ALERT pin high to inform the

microcontroller that a new reading is available. To enable Always On mode, set [CC_EN] = 1.

• In 1-SHOT mode, the CC performs a single 250-ms reading, and similarly sets the CC_READY bit

when completed. This mode is intended for non-gauging usages, where the host simply desires to

check the pack current.

To enable a 1-SHOT reading, ensure [CC_EN] = 0 and set [CC_ONESHOT] = 1.

The full scale range of the CC is ± 270 mV, with a max recommended input range of ± 200 mV, thus

yielding an LSB of approximately 8.44 µV.

The following equation shows how to convert the 16-bit CC reading into an analog voltage if no board-

level calibration is performed:

CC Reading (in µV) = [16-bit 2’s Complement Value] × (8.44 µV/LSB) (3)

16-Bit CC Result ADC Result in Decimal CC Reading (in µV)

0x0001 1 8.44

0x2710 10000 84,400

0x7D00 32000 270,080

0x8300 –32000 –270,080

0xC350 –15536 –131,123.84

0xFFFF –1 –8.44

7.3.1.1.4 External Thermistor

One (bq76920), two (bq76930), or three (bq76940) 10-kΩNTC 103AT thermistors may be measured by

the device. These are measured by applying a factory-trimmed internal 10-k pull-up resistance to an

internal regulator value of nominally 3.3 V, the result of which can be read out from the TSx (TS1, TS2,

TS3) registers.

To select thermistor measurement mode, set [TEMP_SEL] = 1.

Thermistor TS1 is connected between TS1 and VSS; TS2 is connected between TS2 and VC5x (bq76930

and bq76940 only); and TS3 is connected between TS3 and VC10x (bq76940 only). These thermistors

may be placed in various areas in the battery pack to measure such things as localized cell temperature,

FET heating, and so forth.

The thermistor impedance may be calculated using the 14-bit ADC reading in the TS1, TS2, and TS3

registers and 10-k internal pull-up resistance as follows:

The following equations show how to use the 14-bit ADC readings in TS1, TS2, and TS3 to determine the

resistance of the external 103AT thermistor:

VTSX = (ADC in Decimal) x 382 µV/LSB (4)

RTS = (10,000 × VTSX) ÷ (3.3 – VTSX) (5)

To convert the thermistor resistance into temperature, please refer to the thermistor component

manufacturer’s datasheet.

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

7.3.1.1.5 Die Temperature Monitor

NOTE

When switching between external and internal temperature monitoring, a 2-s latency may be

incurred due to the natural scheduler update interval.

A die temperature block generates a voltage that is proportional to the die temperature, and provides a

way of reducing component count if pack thermistors are not used or ensuring that the die power

dissipation requirements are observed. The die is measured using the same on-board 14-bit ADC as the

cell voltages.

To select internal die temperature measurement mode, set [TEMP_SEL] = 0.

For bq76930 and bq76940, multiple die temperature measurements are available. These are stored in

TS2 and TS3.

To convert a DIETEMP reading into temperature, refer to the following equation box. If more accurate

temperature readings are needed from DIETEMP, the DIETEMP at room temperature value should be

stored during production calibration.

The following equation shows how to use the 14-bit ADC readings in TS1, TS2, and TS3 when

[TEMPSEL] = 0 to determine the internal die temperature:

V25 = 1.200 V (nominal) (6)

VTSX = (ADC in Decimal) x 382 µV/LSB (7)

TEMPDIE = 25° – ((VTSX – V25) ÷ 0.0042) (8)

7.3.1.1.6 16-Bit Pack Voltage

Once converted to digital form, each cell voltage is added up and the summation result stored in the BAT

registers. This 16-bit value has a nominal LSB of 1.532 mV.

The following shows how to convert the 16-bit pack voltage ADC reading into an analog voltage. This

value also uses the GAIN and OFFSET stored into EEPROM.

The ADC transfer function is a linear equation defined as follows:

V(BAT) = 4 x GAIN x ADC(cell) + (#Cells x OFFSET) (9)

GAIN is stored in units of µV/LSB, while OFFSET is stored in mV units.

7.3.1.1.7 System Scheduler

A master scheduler oversees the monitoring intervals, creating a full update every 250 ms. Temperature

measurements are taken every 2 seconds. Pack voltage is calculated every 250 ms.

7.3.1.2 Protection Subsystem

7.3.1.2.1 Integrated Hardware Protections

Integrated hardware protections are provided as an extra degree of safety and are meant to supplement

the standard protection feature set that would be incorporated into the host controller firmware. They

should not be used as the sole means of protecting a battery pack, but are useful for FMEA purposes; for

example, in the event that a host microcontroller is unable to react to any of the below protection

situations. All hardware protection thresholds and delays should be loaded into the AFE by the host

microcontroller during system startup. The AFE will also default to pre-defined threshold and delay

settings, in case the host microcontroller is unable to or does not wish to program the protection settings.

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Overcurrent in Discharge (OCD) and Short Circuit in Discharge (SCD) are implemented using sampled

analog comparators that run at 32 kHz, and that continuously monitor the voltage across (SRP–SRN)

while the device is in NORMAL mode. Upon detection of a voltage that exceeds the programmed OCD or

SCD threshold, a counter begins to count up to a programmed delay setting. If the counter reaches its

target value, the SYS_STAT register is updated to indicate the fault condition, the FET state(s) are

updated as shown in

Table 7-1, and the ALERT pin is driven high to interrupt the host.

The protection fault threshold and delay settings for OCD and SCD protections are configured through the

PROTECT1 and PROTECT2 registers. See Section 7.5 for details about supported values.

Overvoltage (OV) and Undervoltage (UV) protections are handled digitally, by comparing the cell voltage

readings against the 8-bit programmed thresholds in the OV and UV registers.

The OV threshold is stored in the OV_TRIP register and is a direct mapping of 8 bits of the 14-bit ADC

reading, with the upper 2 MSB preset to “10” and lower 4 LSB preset to “1000”. In other words, the

corresponding OV trip level is mapped to “10-XXXX-XXXX–1000”. The programmable range of OV

thresholds is approximately 3.15 to 4.7 V, but this is subject to variation due to

the (GAIN, OFFSET) linear equation used to map the ADC values.

The UV threshold is stored in the UV_TRIP register and is a direct mapping of 8 bits of the 14-bit ADC

reading, with the upper 2 MSB preset to “01” and lower 4 LSB preset to “0000”. In other words, the

corresponding OV trip level is mapped to “01-XXXX-XXXX–0000”. The programmable range of UV

thresholds is approximately 1.58 to 3.1 V, but this is subject to variation due to the (GAIN, OFFSET) linear

equation used to map the ADC values.

Protection Upper 2 MSB Middle 8 Bits Lower 4 LSB

OV 10 Set in OV_TRIP Register 1000

UV 01 Set in UV_TRIP Register 0000

NOTE

To support flexible cell configurations within bq76920, bq76930, and bq76940, UV is ignored

on any cells that have a reading under UVMINQUAL. This allows cell pins to be shorted in

implementations where not all cells are needed (for example, 6-series cells using the

bq76930).

Default protection thresholds and delays are shown in the register description at the end of this datasheet.

These are loaded into the digital register (RAM) of the device when the device enters NORMAL mode.

These RAM values may then be overwritten by the host controller to any other values, which they will

retain until a POR event. It is recommended that the host controller reload these values during its standard

power-up and/or re-initialization sequence.

To calculate the correct OV_TRIP and UV_TRIP register values for a device, use the following procedure:

1. Determine desired OV.

2. Read out [ADCGAIN] and [ADCOFFSET] from their corresponding registers. Note that ADCGAIN is

stored in units of µV/LSB, while ADCOFFSET is stored in mV.

3. Calculate the full 14-bit ADC value needed to meet the desired OV and UV trip thresholds as follows:

(a) OV_TRIP_FULL = (OV – ADCOFFSET) ÷ ADCGAIN

(b) UV_TRIP_FULL = (UV – ADCOFFSET) ÷ ADCGAIN

4. Remove the upper 2 MSB and lower 4 LSB from the full 14-bit value, retaining only the remaining

middle 8 bits. This can be done by shifting the OV_TRIP_FULL and UV_TRIP_FULL binary values 4

bits to the right and removing the upper 2 MSB.

5. Write OV_TRIP and UV_TRIP to their corresponding registers.

clamps at ~ 18 V, R1 will limit current to approximately

(V(PACK±) - 18) / R1.

DSG CHG

Q3 is a low-cost PCH FET and is used to keep CHG away

from any voltages below VSS. When CHG is not being

pulled high, PACK± being pulled below VSS will not be

seen by CHG as Q2 does not turn on. Q3 also allows R2 to

keep Q1 OFF, since all voltages below this FET can

Q3 "follow" PACK± as it goes below VSS.

This diode allows CHG

to pull the Q1 gate high.

R1 drops the voltage when PACK± is pulled high and

R1 limits the current going into the CHG pin. Since CHG

(1M)

BAT ±

This zener clamp may

be needed to prevent

Q1 from turning on

too quickly (optional).

PACK t

Rsns R2 clamps Q1 when

CHG is turned off.

(1M)

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Both OV and UV protections require the ADC to be enabled. Ensure that the [ADC_EN] bit is set to 1 if

OV and UV protections are needed.

7.3.1.2.2 Reduced Test Time

A special debug and test configuration bit is provided in the SYS_CTRL2 register, called [DELAY_DIS].

Setting [DELAY_DIS] bypasses the OV/UV protection fault timers and allows a fault condition to be

registered within 200 ms after application of such a fault condition.

7.3.1.3 Control Subsystem

7.3.1.3.1 FET Driving (CHG AND DSG)

Each bq769x0 device provides two low-side FET drivers, CHG and DSG, which control NCH power FETs

or may be used as a signal to enable various other circuits such as a high-side NCH charge pump circuit.

Both DSG and CHG drivers have a fast pull-up to nominally 12 V when enabled. DSG uses a fast pull-

down to VSS when disabled, while CHG utilizes a high impedance (nominally 1 MΩ) pull-down path when

disabled.

An additional internal clamp circuit ensures that the CHG pin does not exceed a maximum of 20 V.

Figure 7-3. CHG and DSG FET Circuit

The power path for the CHG and DSG pull-up circuit originates from the REGSRC pin, instead of BAT.

To enable the CHG fet, set the [CHG_ON] register bit to 1; to disable, set [CHG_ON] = 0. The discharge

FET may be similarly controlled through the [DSG_ON] register bit.

Certain fault conditions or power state transitions will clear the state of the CHG/DSG FET controls.

Table 7-1 shows what action, if any, to take to [CHG_ON] and [DSG_ON] in response to various system

events:

Table 7-1. CHG, DSG Response Under Various System Events

EVENT [CHG_ON] [DSG_ON]

OV Fault Set to 0 —

UV Fault — Set to 0

OCD Fault — Set to 0

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Table 7-1. CHG, DSG Response Under Various System Events (continued)

EVENT [CHG_ON] [DSG_ON]

SCD Fault — Set to 0

ALERT Override Set to 0 Set to 0

DEVICE_XREADY is set Set to 0 Set to 0

Enter SHIP mode from NORMAL Set to 0 Set to 0

NOTE

All protection recovery must be initiated by the host microcontroller. In order to resume FET

operation after a fault condition has occurred, the host microcontroller must first clear the

corresponding status bit in the SYS_STAT register, which will clear the ALERT pin, and then

manually re-enable the CHG and/or DSG bit. Certain faults, such as OV or UV, may

immediately re-toggle if such a condition still persists. Refer to Table 7-3 for details on

clearing status bits.

There are no conditions under which the bq769x0 automatically sets either [CHG_ON] or [DSG_ON] to 1.

7.3.1.3.2 Load Detection

A load detection circuit is present on the CHG pin and activated whenever the CHG FET is disabled

([CHG_ON] = 0). This circuit detects if the CHG pin is externally pulled high when the high impedance

(approximately 1 MΩ) pull-down path should actually be holding the CHG pin to VSS, and is useful for

determining if the PACK– pin (outside of the AFE) is being held at a high voltage—for example, if the load

is present while the power FETs are off. The state of the load detection circuit is read from the

[LOAD_PRESENT] bit of the SYS_CTRL1 register.

After an OCD or SCD fault has occurred, the DSG FET will be disabled ([DSG_ON] cleared), and the

CHG FET must similarly be explicitly disabled to activate the load detection circuit. The host

microcontroller may periodically poll the [LOAD_PRESENT] bit to determine the state of the PACK– pin

and determine when the load is removed ([LOAD_PRESENT] = 0).

7.3.1.3.3 Cell Balancing

Both internal and external passive cell balancing options are fully supported by the bq76920, while

external cell balancing is recommended for bq76930 and bq76940. It is left to the host controller to

determine the exact balancing algorithm to be used in any given system. Each bq769x0 device provides

the cell voltages and balancing drivers to enable this. If using the internal cell balance drivers, up to 50 mA

may be balanced per cell. If using external cell balancing, much higher balancing currents may be

employed.

To activate a particular cell balancing channel, simply set the corresponding bit for that cell in the

CELLBAL1, CELLBAL2, or CELLBAL3 register. For example, VC1–VC0 is enabled by setting [CB1], while

VC12–VC11 is set through [CB12].

Multiple cells may be simultaneously balanced. It is left to the user’s discretion to determine the ideal

number of cells to concurrently balance. Adjacent cells should not be balanced simultaneously. This may

cause cell pins to exceed their absolute maximum conditions and is also not recommended for external

balancing implementations. Additionally, if internal balancing is used, care should be taken to avoid

exceeding package power dissipation ratings.

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

NOTE

The host controller must ensure that no two adjacent cells are balanced simultaneously

within each set of the following:

• VC1–VC5

• VC6–VC10

• VC11–VC15

The total duty cycle devoted to balancing is approximately 70% per 250 ms. This is because a portion of

the 250 ms is allotted for normal cell voltage measurements through the ADC.

If [ADC_EN] =1, OV and UV protections are not affected by cell balancing, since the cell balancing is

temporarily suspended for a small slice of time every 250 ms during which the cell voltage readings are

taken. This ensures that the OV and UV protections do not accidentally trigger, or miss an actual OV/UV

condition on the cells while balancing is enabled.

NOTE

All cell balancing control bits in CELLBAL1, CELLBAL2, and CELLBAL3 are automatically

cleared under the following events, and must be explicitly re-written by the host

microcontroller following clearing of the event:

• DEVICE_XREADY is set

• Enters NORMAL mode from SHIP mode

7.3.1.3.4 Alert

The ALERT pin serves as an active high digital interrupt signal that can be connected to a GPIO port of

the host microcontroller. This signal is an OR of all bits in the SYS_STAT register.

In order to clear the ALERT signal, the source bit in the SYS_STAT register must first be cleared by

writing a “1” to that bit. This will cause an automatic clear of the ALERT pin once all bits are cleared.

The ALERT pin may also be driven by an external source; for example, the pack may include a secondary

overvoltage protector IC. When the ALERT pin is forced high externally while low, the device will

recognize this as an OVRD_ALERT fault and set the [OVRD_ALERT] bit. This triggers automatic disabling

of both CHG and DSG FET drivers. The device cannot recognize the ALERT signal input high when it is

already forcing the ALERT signal high from another condition.

The ALERT pin has no internal debounce support so care should be taken to protect the pin from noise or

other parasitic transients.

NOTE

It is highly recommended to place an external 500 kΩ–1 MΩpull-down resistor from ALERT

to VSS as close to the IC as possible. Additional recommendations are:

a) To keep all traces between the IC and components connected to the ALERT pin very

short.

b) To include a guard ring around the components connected to the ALERT pin and the

pin itself.

7.3.1.3.5 Output LDO

An adjustable output voltage regulator LDO is provided as a simple way to provide power to additional

components in the battery pack, such as the host microcontroller or LEDs. The LDO is configured in

EEPROM by TI during the production test process, and can support 2.5-V or 3.3-V options.

A6 A5 A0

... R7R/W R6 R0

...

... C7 C6 C0

...

Start Slave Address Register

Address

Stop

SCL

SDA A6 A5 A0

... R/WACK ACK ACK

D7 D6 ACK NACK

Slave Address

Slave

Drives CRC

(optional) Master

Drives NACK

Slave

Drives Data

Repeated

Start

A6 A5 A0

... R7R/W R6 R0

... D7 D6 D0

... C7 C6 C0

...

Start Slave Address Register

Address Data CRC

(optional) Stop

SCL

SDA ACK ACK ACK ACK

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

A cascode small-signal FET must be added in the external path between BAT and REGSRC with the

bq76930 and bq76940. This helps drop most of the power dissipation outside of the package and cuts

down on package power dissipation.

7.3.1.4 Communications Subsystem

The AFE implements a standard 100-kHz I2C interface and acts as a slave device. The I2C device

address is 7-bits and is factory programmed. Consult the Device Comparison Table (Section 4) of this

datasheet for more information.

A write transaction is shown in Figure 7-4. Block writes are allowed by sending additional data bytes

before the Stop. The I2C block will auto-increment the register address after each data byte.

When enabled, the CRC is calculated as follows:

• In a single-byte write transaction, the CRC is calculated over the slave address, register address, and

data.

• In a block write transaction, the CRC for the first data byte is calculated over the slave address,

The CRC polynomial is x8 + x2 + x + 1, and the initial value is 0.

When the slave detects a bad CRC, the I2C slave will NACK the CRC, which causes the I2C slave to go to

an idle state.

Figure 7-4. I2C Write

Figure 7-5 shows a read transaction using a Repeated Start.

Figure 7-5. I2C Read with Repeated Start

Figure 7-6 shows a read transaction where a Repeated Start is not used, for example if not available in

hardware. For a block read, the master ACK’s each data byte except the last and continues to clock the

interface. The I2C block will auto-increment the register address after each data byte.

When enabled, the CRC for a read transaction is calculated as follows:

• In a single-byte read transaction, the CRC is calculated after the second start and uses the slave

address and data byte.

A6 A5 A0

... R7R/W R6 R0

...

... C7 C6 C0

...

Start Slave Address Register

Address

Stop

SCL

SDA A6 A5 A0

... R/WACK ACK ACK

D7 D6 ACK NACK

Slave Address

Slave

Drives CRC

(optional) Master

Drives NACK

Slave

Drives Data

Stop Start

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

• In a block read transaction, the CRC for the first data byte is calculated after the second start and uses

the slave address and data byte. The CRC for subsequent data bytes is calculated over the data byte

only.

The CRC polynomial is x8 + x2 + x + 1, and the initial value is 0.

When the master detects a bad CRC, the I2C master will NACK the CRC, which causes the I2C slave to

go to an idle state.

Figure 7-6. I2C Read Without Repeated Start

7.4 Device Functional Modes

Each bq769x0 device supports the following modes of operation.

Table 7-2. Supported Power Modes

Mode Description

NORMAL Fully operational state. Both ADC and CC may be on, or disabled by host microcontroller.

OV and UV protection enabled if ADC is on. OCD and SCD enabled. ADC and CC may be

disabled to reduce power consumption, and CC may be operated in a “1-SHOT” mode for

flexible power savings.

SHIP Lowest possible power state, intended for pack assembly and/or long term pack storage.

Must see a BOOT signal (> 1 VBOOT) on TS1 pin to boot from SHIP →NORMAL. Note

that the device always enters SHIP mode upon POR.

7.4.1 NORMAL Mode

NORMAL mode represents the fully operational mode where all blocks are enabled and the device sees

its highest current consumption. In this mode, certain blocks/functions may be disabled to save

power—these include the ADC and CC. OV and UV are running continuously as long as the ADC is

enabled. The OCD and SCD comparators may not be disabled in this mode.

Transitioning from NORMAL to SHIP mode is also initiated by the host, and requires consecutive writes to

two bits in the SYS_CTRL1 register.

7.4.2 SHIP Mode

SHIP mode is the basic and lowest power mode that bq769x0 supports. SHIP mode is automatically

entered during initial pack assembly and after every POR event. When the device is in NORMAL mode, it

may enter SHIP by the host controller through a specific sequence of I2C commands.

In SHIP mode, only a minimum of blocks are turned on, including the VSTUP power supply and primal

boot detector. Waking from SHIP mode to NORMAL mode requires pulling the TS1 pin greater than

VBOOT, which triggers the device boot-up sequence.

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

To enter SHIP mode from NORMAL mode, the [SHUT_A] and [SHUT_B] bits in the SYS_CTRL1 register

must be written with specific patterns across two consecutive writes:

• Write #1: [SHUT_A] = 0, [SHUT_B] = 1

• Write #2: [SHUT_A] = 1, [SHUT_B] = 0

Note that [SHUT_A] and [SHUT_B] should each be in a 0 state prior to executing the shutdown command

above. If this specific sequence is entered into the device, the device transitions into SHIP mode. If any

other sequence is written to the [SHUT_A] and [SHUT_B] bits or if either of the two patterns is not

correctly entered, the device will not enter SHIP mode.

CAUTION

DO NOT OPERATE THE DEVICE BELOW POR. When designing with the

bq76940, the intermediate voltages (BAT–VC10x), (VC10x–VC5x), and

(VC5x–VSS) must each never fall below VSHUT. When this occurs, a full device

reset must be initiated by powering down all three intermediate voltages

(BAT–VC10x), (VC10x–VC5x), and (VC5x–VSS) below VSHUT and rebooting by

applying the appropriate VBOOT signal to the TS1 pin. When designing with

the bq76930, the intermediate voltages (BAT–VC5x) and (VC5x–VSS) must

each never fall below VSHUT. If this occurs, a full device reset must be initiated

by powering down both intermediate voltages (BAT–VC5x) and (VC5x–VSS)

below VSHUT and rebooting by applying the appropriate VBOOT signal to the

TS1 pin.

The device will also enter SHIP mode during a POR event; however, this is not a recommended method

of SHIP mode entry. If any of the supply-side voltages below fall below VSHUT and then back up above

VPORA, the device defaults into the SHIP mode state. This is similar to an initial pack assembly condition.

In order to exit SHIP mode into NORMAL mode, the device must follow the standard boot sequence by

applying a voltage greater than the VBOOT threshold on the TS1 pin.

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

(1) These registers are only valid for bq76930 and bq76940.

(2) These registers are only valid for bq76940.

7.5 Register Maps

Name Addr D7 D6 D5 D4 D3 D2 D1 D0

SYS_STAT 0x00 CC_READY RSVD DEVICE_

XREADY OVRD_

ALERT UV OV SCD OCD

CELLBAL1 0x01 RSVD RSVD RSVD CB<5:1>

CELLBAL2(1) 0x02 RSVD RSVD RSVD CB<10:6>

CELLBAL3(2) 0x03 RSVD RSVD RSVD CB<15:11>

SYS_CTRL1 0x04 LOAD_

PRESENT RSVD RSVD ADC_EN TEMP_SEL RSVD SHUT_A SHUT_B

SYS_CTRL2 0x05 DELAY_DIS CC_EN CC_

ONESHOT RSVD DSG_ON CHG_ON

PROTECT1 0x06 RSNS RSVD RSVD SCD_DELAY SCD_THRESH

PROTECT2 0x07 RSVD OCD_DELAY OCD_THRESH

PROTECT3 0x08 UV_DELAY OV_DELAY RSVD

OV_TRIP 0x09 OV_THRESH

UV_TRIP 0x0A UV_THRESH

CC_CFG 0x0B RSVD RSVD Must be programmed to 0x19

VC1_HI 0x0C RSVD RSVD <13:8>

VC1_LO 0x0D <7:0>

VC2_HI 0x0E RSVD RSVD <13:8>

VC2_LO 0x0F <7:0>

VC3_HI 0x10 RSVD RSVD <13:8>

VC3_LO 0x11 <7:0>

VC4_HI 0x12 RSVD RSVD <13:8>

VC4_LO 0x13 <7:0>

VC5_HI 0x14 RSVD RSVD <13:8>

VC5_LO 0x15 <7:0>

VC6_HI(1) 0x16 RSVD RSVD <13:8>

VC6_LO(1) 0x17 <7:0>

VC7_HI(1) 0x18 RSVD RSVD <13:8>

VC7_LO(1) 0x19 <7:0>

VC8_HI(1) 0x1A RSVD RSVD <13:8>

VC8_LO(1) 0x1B <7:0>

VC9_HI(1) 0x1C RSVD RSVD <13:8>

VC9_LO(1) 0x1D <7:0>

VC10_HI(1) 0x1E RSVD RSVD <13:8>

VC10_LO(1) 0x1F <7:0>

VC11_HI(2) 0x20 RSVD RSVD <13:8>

VC11_LO(2) 0x21 <7:0>

VC12_HI(2) 0x22 RSVD RSVD <13:8>

VC12_LO(2) 0x23 <7:0>

VC13_HI(2) 0x24 RSVD RSVD <13:8>

VC13_LO(2) 0x25 <7:0>

VC14_HI(2) 0x26 RSVD RSVD <13:8>

VC14_LO(2) 0x27 <7:0>

VC15_HI(2) 0x28 RSVD RSVD <13:8>

VC15_LO(2) 0x29 <7:0>

BAT_HI 0x2A <15:8>

BAT_LO 0x2B <7:0>

TS1_HI 0x2C RSVD RSVD <13:8>

TS1_LO 0x2D <7:0>

TS2_HI(1) 0x2E RSVD RSVD <13:8>

TS2_LO(1) 0x2F <7:0>

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Name Addr D7 D6 D5 D4 D3 D2 D1 D0

TS3_HI(2) 0x30 RSVD RSVD <13:8>

TS3_LO(2) 0x31 <7:0>

CC_HI 0x32 <15:8>

CC_LO 0x33 <7:0>

ADCGAIN1 0x50 RSVD ADCGAIN<4:3> RSVD

ADCOFFSET 0x51 ADCOFFSET<7:0>

ADCGAIN2 0x59 ADCGAIN<2:0> RSVD

7.5.1 Register Details

Table 7-3. SYS_STAT (0x00)

BIT76543210

NAME CC_READY RSVD DEVICE_

XREADY OVRD_

ALERT UV OV SCD OCD

RESET00000000

ACCESS RW RW RW RW RW RW RW RW

NOTE

Bits in SYS_STAT may be cleared by writing a "1" to the corresponding bit.

Writing a "0" does not change the state of the corresponding bit.

CC_READY (Bit 7): Indicates that a fresh coulomb counter reading is available. Note that if this bit is not

cleared between two adjacent CC readings becoming available, the bit remains latched to 1. This bit may

only be cleared (and not set) by the host.

0 = Fresh CC reading not yet available or bit is cleared by host microcontroller.

1 = Fresh CC reading is available. Remains latched high until cleared by host.

RSVD (Bit 6): Reserved. Do not use.

DEVICE_XREADY (Bit 5): Internal chip fault indicator. When this bit is set to 1, it should be cleared by

the host. May be set due to excessive system transients. This bit may only be cleared (and not set) by

the host.

0 = Device is OK.

1 = Internal chip fault detected, recommend that host microcontroller clear this bit after waiting a

few seconds. Remains latched high until cleared by the host.

OVRD_ALERT (Bit 4): External pull-up on the ALERT pin indicator. Only active when ALERT pin is not

already being driven high by the AFE itself.

0 = No external override detected

1 = External override detected. Remains latched high until cleared by the host.

UV (Bit 3): Undervoltage fault event indicator.

0 = No UV fault is detected.

1 = UV fault is detected. Remains latched high until cleared by the host.

OV (Bit 2): Overvoltage fault event indicator.

0 = No OV fault is detected.

1 = OV fault is detected. Remains latched high until cleared by the host.

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

SCD (Bit 1): Short circuit in discharge fault event indicator.

0 = No SCD fault is detected.

1 = SCD fault is detected. Remains latched high until cleared by the host.

OCD (Bit 0): Over current in discharge fault event indicator.

0 = No OCD fault is detected.

1 = OCD fault is detected. Remains latched high until cleared by the host.

Table 7-4. CELLBAL1 (0x01) for bq76920, bq76930, and bq76940

BIT76543210

NAME — — — CB5 CB4 CB3 CB2 CB1

RESET00000000

ACCESS R R R RW RW RW RW RW

CBx (Bits 4–0):

0 = Cell balancing on Cell “x” is disabled.

1 = Cell balancing on Cell “x” is enabled.

Table 7-5. CELLBAL2 (0x02) for bq76930 and bq76940

BIT76543210

NAME — — — CB10 CB9 CB8 CB7 CB6

RESET00000000

ACCESS R R R RW RW RW RW RW

CBx (Bits 4–0):

0 = Cell balancing on Cell “x” is disabled.

1 = Cell balancing on Cell “x” is enabled.

Table 7-6. CELLBAL3 (0x03) for bq76940

BIT76543210

NAME — — — CB15 CB14 CB13 CB12 CB11

RESET00000000

ACCESS R R R RW RW RW RW RW

CBx (Bits 4–0):

0 = Cell balancing on Cell “x” is disabled.

1 = Cell balancing on Cell “x” is enabled.

Table 7-7. SYS_CTRL1 (0x04)

BIT76543210

NAME LOAD_

PRESENT — — ADC_EN TEMP_SEL RSVD SHUT_A SHUT_B

RESET00000000

ACCESS R R R RW RW RW RW RW

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

LOAD_PRESENT (Bit 7): Valid only when [CHG_ON] = 0. Is high if CHG pin is detected to exceed

VLOAD_DETECT while CHG_ON = 0, which suggests that external load is present. Note this bit is read-

only and automatically clears when load is removed.

0 = CHG pin < VLOAD_DETECT or [CHG_ON] = 1.

1 = CHG pin >VLOAD_DETECT, while [CHG_ON] = 0.

ADC_EN (Bit 4): ADC enable command

0 = Disable voltage and temperature ADC readings (also disables OV protection)

1 = Enable voltage and temperature ADC readings (also enables OV protection)

TEMP_SEL (Bit 3): TSx_HI and TSx_LO temperature source

0 = Store internal die temperature voltage reading in TSx_HI and TSx_LO

1 = Store thermistor reading in TSx_HI and TSx_LO (all thermistor ports)

RSVD (Bit 2): Reserved, do not set to 1.

SHUT_A, SHUT_B (Bits 1–0): Shutdown command from host microcontroller. Must be written in a

specific sequence, shown below:

Starting from: [SHUT_A] = 0, [SHUT_B] = 0

Write #1: [SHUT_A] = 0, [SHUT_B] = 1

Write #2: [SHUT_A] = 1, [SHUT_B] = 0

Other writes cause the command to be ignored.

Table 7-8. SYS_CTRL2 (0x05)

BIT76543210

NAME DELAY_DIS CC_EN CC_

ONESHOT RSVD RSVD RSVD DSG_ON CHG_ON

RESET00000000

ACCESS RW RW RW RW RW RW RW RW

DELAY_DIS (Bit 7): Disable OV, UV, OCD, and SCD delays for faster customer production testing.

0 = Normal delay settings

1 = OV, UV, OCD, and SCD delay circuit is bypassed, creating zero delay (approximately

250 ms).

CC_EN (Bit 6): Coulomb counter continuous operation enable command. If set high, [CC_ONESHOT] bit

is ignored.

0 = Disable CC continuous readings

1 = Enable CC continuous readings and ignore [CC_ONESHOT] state

CC_ONESHOT (Bit 5): Coulomb counter single 250-ms reading trigger command. If set to 1, the

coulomb counter will be activated for a single 250-ms reading, and then turned back off.

[CC_ONESHOT] will also be cleared at the conclusion of this reading, while [CC_READY] bit will be set

to 1. 0 = No action

1 = Enable single CC reading (only valid if [CC_EN] = 0), and [CC_READY] = 0)

RSVD (Bit 4–2): Reserved. Do not use.

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

DSG_ON (Bit 1): Discharge FET driver (low side NCH) or discharge signal control

0 = DSG is off.

1 = DSG is on.

CHG_ON (Bit 0): Discharge FET driver (low side NCH) or discharge signal control

0 = CHG is off.

1 = CHG is on.

Table 7-9. PROTECT1 (0x06)

BIT76543210

NAME RSNS — RSVD SCD_D1 SCD_D0 SCD_T2 SCD_T1 SCD_T0

RESET00000000

ACCESS RW R RW RW RW RW RW RW

RSNS (Bit 7): Allows for doubling the OCD and SCD thresholds simultaneously

0 = OCD and SCD thresholds at lower input range

1 = OCD and SCD thresholds at upper input range

RSVD (Bit 5): Reserved, do not set to 1.

SCD_D1:0 (Bits 4–3):

Short circuit in discharge delay setting. A 400-µs setting is recommended only in systems using

maximum cell measurement input resistance, Rc, of 1 kΩ(which corresponds to minimum internal cell

balancing current or external cell balancing configuration).

Code (in µs)

0x0 70

0x1 100

0x2 200

0x3 400

SCD_T2:0 (Bits 2–0): Short circuit in discharge threshold setting

Code RSNS = 1 (in mV) RSNS = 0 (in mV)

0x0 44 22

0x1 67 33

0x2 89 44

0x3 111 56

0x4 133 67

0x5 155 78

0x6 178 89

0x7 200 100

Table 7-10. PROTECT2 (0x07)

BIT76543210

NAME — OCD_D2 OCD_D1 OCD_D0 OCD_T3 OCD_T2 OCD_T1 OCD_T0

RESET00000000

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Table 7-10. PROTECT2 (0x07) (continued)

BIT76543210

ACCESS R RW RW RW RW RW RW RW

OCD_D2:0 (Bits 6–4): Overcurrent in discharge delay setting

Code (in ms)

0x0 8

0x1 20

0x2 40

0x3 80

0x4 160

0x5 320

0x6 640

0x7 1280

OCD_T3:0 (Bits 3–0): Overcurrent in discharge threshold setting.

Code RSNS = 1 (in mV) (RSNS = 0 (in mV)

0x0 17 8

0x1 22 11

0x2 28 14

0x3 33 17

0x4 39 19

0x5 44 22

0x6 50 25

0x7 56 28

0x8 61 31

0x9 67 33

0xA 72 36

0xB 78 39

0xC 83 42

0xD 89 44

0xE 94 47

0xF 100 50

Table 7-11. PROTECT3 (0x08)

BIT76543210

NAME UV_D1 UV_D0 OV_D1 OV_D0 RSVD RSVD RSVD RSVD

RESET00000000

ACCESS RW RW RW RW RW RW RW RW

UV_D1:0 (Bits 7–6): Undervoltage delay setting

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Code (in s)

0x0 1

0x1 4

0x2 8

0x3 16

OV_D1:0 (Bits 5–4): Overvoltage delay setting

Code (in s)

0x0 1

0x1 2

0x2 4

0x3 8

RSVD (Bits 3–0): These bits are for TI internal debug use only and must be configured to the default

settings indicated.

Table 7-12. OV_TRIP (0x09)

BIT76543210

NAME OV_T7 OV_T6 OV_T5 OV_T4 OV_T3 OV_T2 OV_T1 OV_T0

RESET10101100

ACCESS RW RW RW RW RW RW RW RW

OV_T7:0 (Bits 7–0): Middle 8 bits of the direct ADC mapping of the desired OV protection threshold,

with upper 2 MSB set to 10 and lower 2 LSB set to 1000. The equivalent OV threshold is mapped to:

10-OV_T<7:0>1000.

By default, OV_TRIP is configured to a 0xAC setting.

Note that OV_TRIP is based on the ADC voltage, which requires back-calculation using the GAIN and

OFFSET values stored in ADCGAIN<4:0>and ADCOFFSET<7:0>.

Table 7-13. UV_TRIP (0x0A)

BIT76543210

NAME UV_T7 UV_T6 UV_T5 UV_T4 UV_T3 UV_T2 UV_T1 UV_T0

RESET10010111

ACCESS RW RW RW RW RW RW RW RW

UV_T7:0 (Bits 7–0): Middle 8 bits of the direct ADC mapping of the desired UV protection threshold, with

upper 2 MSB set to 01 and lower 4 LSB set to 0000. In other words, the equivalent OV threshold is

mapped to: 01-UV_T<7:0>–0000.

By default, UV_TRIP is configured to a 0x97 setting. .

Note that UV_TRIP is based on the ADC voltage, which requires back-calculation using the GAIN and

OFFSET values stored in ADCGAIN<4:0>and ADCOFFSET<7:0>.

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Table 7-14. CC_CFG REGISTER (0x0B)

BIT76543210

NAME — — CC_CFG5 CC_CFG4 CC_CFG3 CC_CFG2 CC_CFG1 CC_CFG0

RESET00000000

ACCESS R R RW RW RW RW RW RW

CC_CFG5:0 (Bits 5–0): For optimal performance, these bits should be programmed to 0x19 upon device

startup.

7.5.2 Read-Only Registers

Table 7-15. CELL VOLTAGE REGISTERS

VC1_HI, _LO (0x0C–0x0D), VC2_HI, _LO (0x0E–0x0F), VC3_HI, _LO (0x10–0x11), VC4_HI, _LO (0x12–0x13), VC5_HI, _LO

(0x14–0x15) / bq76930, bq76940: VC6_HI, _LO (0x16–0x17), VC7_HI, _LO (0x18–0x19), VC8_HI, _LO (0x1A–0x1B), VC9_HI, _LO

(0x1C–0x1D), VC10_HI, _LO (0x1E–0x1F) / bq76940: VC11_HI, _LO (0x20–0x21), VC12_HI, _LO (0x22–0x23), VC13_HI, _LO

(0x24–0x25), VC14_HI, _LO (0x26–0x27), VC15_HI, _LO (0x28–0x29)

BIT76543210

NAME — — D13 D12 D11 D10 D9 D8

RESET00000000

NAME D7 D6 D5 D4 D3 D2 D1 D0

RESET00000000

D11:8 (Bits 3–0): Cell “x” ADC reading, upper 6 MSB. Always returned as an atomic value if both high

and low registers are read in the same transaction (using address auto-increment).

D7:0 (Bits 7–0): Cell ”x” ADC reading, lower 8 LSB.

Table 7-16. BAT_HI (0x2A) and BAT_LO (0x2B)

BIT76543210

NAME D15 D14 D13 D12 D11 D10 D9 D8

RESET00000000

NAME D7 D6 D5 D4 D3 D2 D1 D0

RESET00000000

D15:8 (Bits 7–0): BAT calculation based on adding up Cells 1–15, upper 8 MSB. Always returned as an

atomic value if both high and low registers are read in the same transaction (using address auto-

increment).

D7:0 (Bits 7–0): BAT calculation based on adding up Cells 1–15, lower 8 LSB

Table 7-17. TS1_HI (0x2C) and TS1_LO (0x2D)

BIT76543210

NAME — — D13 D12 D11 D10 D9 D8

RESET00000000

NAME D7 D6 D5 D4 D3 D2 D1 D0

RESET00000000

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

D11:8 (Bits 3–0): TS1 or DIETEMP ADC reading, upper 6 MSB. Always returned as an atomic value if

both high and low registers are read in the same transaction (using address auto-increment).

D7:0 (Bits 7–0): TS1 or DIETEMP ADC reading, lower 8 LSB

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Table 7-18. TS2_HI (0x2E) and TS2_LO (0x2F)

BIT76543210

NAME — — D13 D12 D11 D10 D9 D8

RESET00000000

NAME D7 D6 D5 D4 D3 D2 D1 D0

RESET00000000

D11:8 (Bits 3–0): TS2 ADC reading, upper 6 MSB. Always returned as an atomic value if both high and

low registers are read in the same transaction (using address auto-increment).

D7:0 (Bits 7–0): TS2 ADC reading, lower 8 LSB

Table 7-19. TS3_HI (0x30) and TS3_LO (0x31)

BIT76543210

NAME — — D13 D12 D11 D10 D9 D8

RESET00000000

NAME D7 D6 D5 D4 D3 D2 D1 D0

RESET00000000

D11:8 (Bits 3–0): TS3 ADC reading, upper 6 MSB. Always returned as an atomic value if both high and

low registers are read in the same transaction (using address auto-increment).

D7:0 (Bits 7–0): TS3 ADC reading, lower 8 LSB

Table 7-20. CC_HI (0x32) and CC_LO (0x33)

BIT76543210

NAME CC15 CC14 CC13 CC12 CC11 CC10 CC9 CC8

RESET00000000

NAME CC7 CC6 CC5 CC4 CC3 CC2 CC1 CC0

RESET00000000

CC15:8 (Bits 7–0): Coulomb counter upper 8 MSB. Always returned as an atomic value if both high and

low registers are read in the same transaction (using address auto-increment).

CC7:0 (Bits 7–0): Coulomb counter lower 8 LSB

Table 7-21. ADCGAIN1 (0x50)

BIT76543210

NAME — — — — ADCGAIN4 ADCGAIN3 — —

RESET————————

ACCESS R R R R R R R R

Table 7-22. ADCGAIN2 (0x59)

BIT76543210

NAME ADCGAIN2 ADCGAIN1 ADCGAIN0 — — — — —

RESET————————

ACCESS R R R R R R R R

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

ADCGAIN4:3 (Bits 3–2, address 0x50):

ADC GAIN

offset upper 2 MSB

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

ADCGAIN2:0 (Bits 7–5, address 0x59):

ADC GAIN offset lower 3 LSB

ADCGAIN<4:0> is a production-trimmed value for the ADC transfer function, in

units of µV/LSB. The range is 365 µV/LSB to 396 µV/LSB, in steps of 1 µV/LSB,

and may be calculated as follows:

GAIN = 365 µV/LSB + (ADCGAIN<4:0>in decimal) × (1 µV/LSB)

Alternately, a conversion table is provided below:

ADC GAIN Gain (µV/LSB) ADC GAIN Gain (µV/LSB)

0x00 365 0x10 381

0x01 366 0x11 382

0x02 367 0x12 383

0x03 368 0x13 384

0x04 369 0x14 385

0x05 370 0x15 386

0x06 371 0x16 387

0x07 372 0x17 388

0x08 373 0x18 389

0x09 374 0x19 390

0x0A 375 0x1A 391

0x0B 376 0x1B 392

0x0C 377 0x1C 393

0x0D 378 0x1D 394

0x0E 379 0x1E 395

0x0F 380 0x1F 396

Table 7-23. ADCOFFSET (0x51)

BIT76543210

NAME ADC

OFFSET7 ADC

OFFSET6 ADC

OFFSET5 ADC

OFFSET4 ADC

OFFSET3 ADC

OFFSET2 ADC

OFFSET1 ADC

OFFSET0

RESET————————

ACCESS R R R R R R R R

ADCOFFSET7:0 (Bits 7–0):

ADC offset, stored in 2’s complement format in mV units. Positive full-scale range

corresponds to 0x7F and negative full-scale corresponds to 0x80. The full-scale

input range is –128 mV to 127 mV, with an LSB of 1 mV.

The table below shows example offsets.

ADCOFFSET Offset (mV)

0x00 0

0x01 1

0x7F 127

0x80 –128

0x81 –127

0xFF –1

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

8 Application and Implementation

NOTE

Information in the following application section is not part of the TI component specification,

and TI does not warrant its accuracy or completeness. TI’s customers are responsible for

determining suitability of components for their purposes. Customers should validate and test

their design implementation to confirm system functionality.

8.1 Application Information

The bq769x0 family of battery monitoring AFEs enabling cell parametric measurement and protection is a

variety of 3-series to 15-series Li-Ion/Li Polymer battery packs.

To evaluate the performance and configurations of the device users need the bq76940, bq76930, and

bq76920 Evaluation Software, (SLUCC539) tool to configure the internal registers for a specific battery

pack and application. The Evaluation Software tool is a graphical user-interface tool installed on a PC

during development. This can be used in conjunction with the bq76920EVM, bq76930EVM or

bq76940EVM.

The bq769x0 devices are expected to be implemented in a system with a microcontroller that can perform

additional functions based on the data made collected. The bq78350 is one example of a companion to

the bq769x0 family.

8.1.1 Configuring Alternative Cell Counts

Each bq769x0 family of IC's support a variety of cell counts. The following tables provide guidance on

which device and which input pins to use, depending on the number of cells in the pack.

Table 8-1. Cell Connections for bq76920

Cell Input 3 Cells 4 Cells 5 Cells

VC5–VC4 CELL 3 CELL 4 CELL 5

VC4–VC3 short short CELL 4

VC3–VC2 short CELL 3 CELL 3

VC2–VC1 CELL 2 CELL 2 CELL 2

VC1–VC0 CELL 1 CELL 1 CELL 1

Table 8-2. Cell Connections for bq76930

Cell Input 6 Cells 7 Cells 8 Cells 9 Cells 10 Cells

VC10–VC9 CELL 6 CELL 7 CELL 8 CELL 9 CELL 10

VC9–VC8 short short short short CELL 9

VC8–VC7 short short CELL 7 CELL 8 CELL 8

VC7–VC6 CELL 5 CELL 6 CELL 6 CELL 7 CELL 7

VC6–VC5b CELL 4 CELL 5 CELL 5 CELL 6 CELL 6

VC5–VC4 CELL 3 CELL 4 CELL 4 CELL 5 CELL 5

VC4–VC3 short short short CELL 4 CELL 4

VC3–VC2 short CELL 3 CELL 3 CELL 3 CELL 3

VC2–VC1 CELL 2 CELL 2 CELL 2 CELL 2 CELL 2

VC1–VC0 CELL 1 CELL 1 CELL 1 CELL 1 CELL 1

Rsns

100

0.1 µF

4.7 µF

BAT

VC5

VC4

VC3

VC2

VC1

VSS

SCL

SDA

CHG

DSG

REGSRC

REGOUT

SRN

SRP

VC0

CAP1

TS1 Cf

100

0.1 µF

1 µF

1M1M

10k

ALERT

PUSH-BUTTON FOR BOOT

VCC

GPIO

SDA

SCL

VSS

1 µF

0.1 µF

10 kΩ

PACK +

PACK–

Companion

Controller

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Table 8-3. Cell Connections for bq76940

Cell Input 9 Cells 10 Cells 11 Cells 12 Cells 13 Cells 14 Cells 15 Cells

VC15–VC14 CELL 9 CELL 10 CELL 11 CELL 12 CELL 13 CELL 14 CELL 15

VC14–VC13 short short short short short short CELL 14

VC13–VC12 short short short CELL 11 CELL 12 CELL 13 CELL 13

VC12–VC11 CELL 8 CELL 9 CELL 10 CELL 10 CELL 11 CELL 12 CELL 12

VC11–VC10b CELL 7 CELL 8 CELL 9 CELL 9 CELL 10 CELL 11 CELL 11

VC10–VC9 CELL 6 CELL 7 CELL 8 CELL 8 CELL 9 CELL 10 CELL 10

VC9–VC8 short short short short short CELL 9 CELL 9

VC8–VC7 short short CELL 7 CELL 7 CELL 8 CELL 8 CELL 8

VC7–VC6 CELL 5 CELL 6 CELL 6 CELL 6 CELL 7 CELL 7 CELL 7

VC6–VC5b CELL 4 CELL 5 CELL 5 CELL 5 CELL 6 CELL 6 CELL 6

VC5–VC4 CELL 3 CELL 4 CELL 4 CELL 4 CELL 5 CELL 5 CELL 5

VC4–VC3 short short short short CELL 4 CELL 4 CELL 4

VC3–VC2 short CELL 3 CELL 3 CELL 3 CELL 3 CELL 3 CELL 3

VC2–VC1 CELL 2 CELL 2 CELL 2 CELL 2 CELL 2 CELL 2 CELL 2

VC1–VC0 CELL 1 CELL 1 CELL 1 CELL 1 CELL 1 CELL 1 CELL 1

8.2 Typical Applications

CAUTION

The external circuitries in the following schematics show minimum requirements

to ensure device robustness during cell connection to the PCB and normal

operation.

Figure 8-1. bq76920 with bq78350 Companion Controller IC

Rsns

100

0.1 µF

4.7 µF

VC5x

VC5

VC4

VC3

VC2

VC1

VSS

SCL

SDA

CHG

DSG

REGSRC

REGOUT

SRN

SRP

VC0

CAP1

TS1 Cf

100

0.1 µF

1µF

1M1M

10k

ALERT

PUSH-BUTTON FOR BOOT

VCC

GPIO

SDA

SCL

VSS

1µF

0.1 µF

10 kΩ

PACK +

PACK -

VC10

VC9

VC8

VC7

VC6

VC5b

BAT

CAP2

TS2 Cf

1 µF

10k

VC5x

Companion

Controller

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Figure 8-2. bq76930 With bq78350 Companion Controller IC

Rsns

100

0.1 µF

4.7 µF

VC5x

VC5

VC4

VC3

VC2

VC1

VSS

SCL

SDA

CHG

DSG

REGSRC

REGOUT

SRN

SRP

VC0

CAP1

TS1 Cf

100

0.1 µF

1 µF

1M1M

10k

ALERT

PUSH-BUTTON FOR BOOT

VCC

GPIO

SDA

SCL

VSS

1 µF

0.1 µF

10 kΩ

PACK +

PACK –

VC10

VC9

VC8

VC7

VC6

VC5b

VC10x

CAP2

TS2 Cf

1 µF

10k

VC15

VC14

VC13

VC12

VC11

VC10b

BAT

CAP3

TS3 Cf

1 µF

10k

VC5x

Companion

Controller

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Figure 8-3. bq76940 with bq78350 Companion Controller IC

8.2.1 Design Requirements

Table 8-4. bq769x0 Design Requirements

DESIGN PARAMETER EXAMPLE VALUE at TA = 25°C

Minimum system operating voltage 24 V

Cell minimum operating voltage 3.0 V

Series Cell Count 8

Charge Voltage 33.6 V

Maximum Charge Current 3.0 A

Peak Discharge Current 10.0 A

OV Protection Threshold 4.30 V

OV Protection Delay 2s

UV Protection Threshold 2.5 V

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Table 8-4. bq769x0 Design Requirements (continued)

DESIGN PARAMETER EXAMPLE VALUE at TA = 25°C

UV Protection Delay 4s

OCD Protection Threshold Max 15 A

OCD Protection Delay Time 320 ms

SCD Protection Threshold Max 25 A

SCD Protection Delay Time 100 µs

8.2.2 Detailed Design Procedure

To begin the design process, there are some key steps required for component selection and protection

configuration.

8.2.2.1 Step-by-Step Design Procedure

• Determine the number of series cells.

– This value depends on the cell chemistry and the load requirements of the system. For example, to

support a minimum battery voltage of 24 V using Li-CO2 type cells with a cell minimum voltage of

3.0 V, there needs to be at least 8-series cells.

• Select the correct bq769x0 device.

– For 8-series cells, the bq76930 is needed.

– For the correct cell connections, see Table 8-2.

• Select the correct protection FETs.

– The bq76930 uses a low-side drive suitable for N-CH FETs.

– These FETs should be rated for the maximum:

• Voltage, which should be approximately 5 V (DC) 10 V (peak) per series cell: for example, 40 V.

• Current, which should be calculated based on both the maximum DC current and the maximum

transient current with some margin: for example, 30 A.

• Power Dissipation, which can be a factor of the RDS(ON) rating of the FET, the FET package,

and the PCB design: for example, 5 W, assuming 5 mΩRDS(ON).

• Select the correct sense resistor.

– The resistance value should be selected to maximize the input bandwidth use of the coulomb

counter range, CCRANGE, but not exceed the absolute maximum ratings.

• Using the normal max discharge current, RSNS = 200 mV / 10.0 A = 20 mΩ.

• However, considering ISCD of 25 A and Abs Max SRP–SRN input of –300 mV, RSNS = 300 mV

/25A=7.5mΩ

• The maximum operating current of the system should also be considered as this should be

below the maximum OCD Threshold, which with a RSNS of 7.5 mΩgives a max OCD current

setting of 13.3 A.

– Further tolerance analysis (value tolerance, temperature variation, and so on) and PCB design

margin should also be considered, so RSNS of 5 mΩwould be suitable with a 75-ppm temperature

coefficient and power rating of 5 W.

• The bq76930 is chosen, and so the REGSRC pin needs to be powered through a source follower

circuit where the FET is used to provide current for REGSRC from the battery positive terminal while

reducing the voltage to a suitable value for the IC.

– The FET also dissipates the power resulting from the load current and dropped voltage external to

the IC and care should be taken to ensure the correct dissipation ratings are specified by the

chosen FET.

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

• Configure the Current-based protection settings through PROTECT1 and PROTECT2:

– Ideal SCD Threshold = 25 A × 5 mΩ= 125 mV.

• However, the closest options are 111 mV (0x03) and 133 mV (0x04) providing 22.2 A and 26.6

A, respectively. Both options have the RSNS bit = 1.

• 0x03 (22.2 A) will be used in this example.

– The SCD delay threshold setting for a 100 µs delay is 0x01.

– Therefore, PROTECT1 should be programmed with 0x8C.

– Ideal OCD Threshold = 15 A × 5 mΩ= 75 mV.

• However, the closest options are 72 mV (0x0A) and 78 mV (0x0B), providing 14.4 A and 15.6 A,

respectively. Both options have the RSNS bit = 1.

• 0x0A (14,4A) will be used in this example.

– The OCD delay threshold setting for a 320-ms delay is 0x05.

– Therefore, PROTECT2 should be programmed with 0x5B.

NOTE

Care should be taken when determining the setting of OV_TRIP and UV_TRIP as these are

ADC value outputs and correlation to cell voltage also requires consideration of the ADC

GAIN and ADC OFFSET registers. More specific details can be found in Section 7.3.1.2.

• Configure the Voltage-based protection settings through OV_TRIP, UV_TRIP and PROTECT3:

– The selected OV Threshold is 4.30 V.

• Therefore, OV_TRIP should be programmed with 0xC9.

– The selected UV Threshold is 2.5 V.

• Therefore, UV_TRIP should be programmed with 0x1A.

– The selected OV Delay is 2 s and the selected UV Delay is 4 s.

• Therefore, PROTECT3 should be programmed with 0x50.

±1.6

±1.4

±1.2

±1.0

±0.8

±0.6

±0.4

±0.2

0.0

±40 ±15 10 35 60 85

Offset (uV)

Temperature (ƒC)

C002

±0.004

±0.002

0.000

0.002

0.004

0.006

0.008

0.010

0.012

0.014

0.016

0.018

0.020

2.00 2.30 2.60 2.90 3.20 3.50 3.80 4.10 4.40 4.70 5.00

VCx Error (mV)

VCx Input (V)

VC1 Error

VC2 Error

VC3 Error

VC4 Error

VC5 Error

C001

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

8.2.3 Application Curves

Figure 8-4. bq76930 VCx Error Across Input Range at 25°C Figure 8-5. Coulomb Counter Offset

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

9 Power Supply Recommendations

The bq769x0 devices are powered through the BAT and REGSRC pins but the bq76930 and bq76940

have additional ‘Power’ pins to provide the power to the entire device in the higher cell configurations.

The use of Rf and Cf connected to the BAT pin, noted in the typical application diagrams, are required to

filter system transients from disturbing the device power supply. These components should be placed as

close as to the IC as possible.

Additionally, for the bq76930 and bq76940 there are additional requirements to ensure a stable power

supply to the device. The REGSRC pin is powered through a source follower circuit where the FET is

used to provide current for REGSRC from the battery positive terminal while reducing the voltage to a

suitable value for the IC. The FET also dissipates the power resulting from the load current and dropped

voltage external to the IC and care should be taken to ensure the correct dissipation ratings are specified

by the chosen FET.

The bq76920 does not use a FET because the battery voltage is within the REGSRC range.

High Current Ground Plane Available Area

Low Current Ground Plane Available Area

Ground

interconnect

BAT-

BAT+ PACK+

PACK-

Key components placed here

Protection FETs

Sense Resistor

Key components placed here

bq78350

bq76920/30/40

Measurement Filter

Resistors and Capacitors

RSNS CHGDSG

bq769x0

bq78350

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

10 Layout

10.1 Layout Guidelines

It is strongly recommended for best measurement performance to keep high current signals from

interfering with the measurement system inputs and ground.

A second key recommendation is to ensure that the bq769x0 input filtering capacitors and power

capacitors are connected to a common ground with as little parasitic resistance between the connections

as possible.

10.2 Layout Example

Figure 10-1 shows a guideline of how to place key components compared to respective ground zones,

based on the bq76920, bq76930, and bq76940 EVMs.

Figure 10-1. System Component Placement Layout vs. Ground Zone Guide

CAUTION

Care should be taken when placing key power pin capacitors to minimize PCB

trace impedances. These impedances could result in device resets or other

unexpected operations when the device is at peak power consumption.

Although not shown in the diagrams, this caution also applies to the resistor

and capacitor network surrounding the current sense resistor.

bq76920

REGSRC

REGOUT

BATTERY–

SENSE

RESISTOR

VSS

PCB Trace impedance

VC0

VC1

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Figure 10-2.

Good Layout: Input Capacitor Grounding With Low Parasitic PCB Impedance

bq76920

BATTERY–

SENSE

RESISTOR

VSS

PCB Trace impedance

REGSRC

REGOUT

VC0

VC1

bq76920, bq76930, bq76940

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

Figure 10-3.

Weak Layout: Input Capacitor Grounding with High Parasitic PCB Impedance

bq76920, bq76930, bq76940

www.ti.com

SLUSBK2G –OCTOBER 2013–REVISED MAY 2016

Submit Documentation Feedback

Product Folder Links: bq76920 bq76930 bq76940

11 Device and Documentation Support

11.1 Documentation Support

11.1.1 Related Documentation

For related documentation, see the following: bq76920 Evaluation Module User 's Guide (SLVU924), and

bq76920, bq76930, bq76940 AFE FAQ (SLUUB41).

11.2 Related Links

The table below lists quick access links. Categories include technical documents, support and community

resources, tools and software, and quick access to sample or buy.

Table 11-1. Related Links

PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL

DOCUMENTS TOOLS &

SOFTWARE SUPPORT &

COMMUNITY

bq76920 Click here Click here Click here Click here Click here

bq76930 Click here Click here Click here Click here Click here

bq76940 Click here Click here Click here Click here Click here

11.3 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the

respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views;

see TI's Terms of Use.

TI E2E™ Online Community The TI engineer-to-engineer (E2E) community was created to foster

collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge,

explore ideas and help solve problems with fellow engineers.

TI Embedded Processors Wiki Established to help developers get started with Embedded Processors

from Texas Instruments and to foster innovation and growth of general knowledge about the

hardware and software surrounding these devices.

11.4 Trademarks

E2E is a trademark of Texas Instruments.

I2C is a trademark of NXP B.V. Corporation.

All other trademarks are the property of their respective owners.

11.5 Electrostatic Discharge Caution

This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with

appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.

ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more

susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.

11.6 Glossary

TI Glossary This glossary lists and explains terms, acronyms, and definitions.

12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the

most current data available for the designated devices. This data is subject to change without notice and

revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

PACKAGE OPTION ADDENDUM

www.ti.com 30-Sep-2017

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

BQ7692000PW ACTIVE TSSOP PW 20 70 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7692000

BQ7692000PWR ACTIVE TSSOP PW 20 2000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7692000

BQ7692003PW ACTIVE TSSOP PW 20 70 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7692003

BQ7692003PWR ACTIVE TSSOP PW 20 2000 Green (RoHS

& no Sb/Br) CU NIPDAU | Call TI Level-2-260C-1 YEAR -40 to 85 BQ7692003

BQ7692006PW ACTIVE TSSOP PW 20 70 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7692006

BQ7692006PWR ACTIVE TSSOP PW 20 2000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7692006

BQ7693000DBT ACTIVE TSSOP DBT 30 60 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7693000

BQ7693000DBTR ACTIVE TSSOP DBT 30 2000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7693000

BQ7693001DBT ACTIVE TSSOP DBT 30 60 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7693001

BQ7693001DBTR ACTIVE TSSOP DBT 30 2000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7693001

BQ7693002DBT ACTIVE TSSOP DBT 30 60 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7693002

BQ7693002DBTR ACTIVE TSSOP DBT 30 2000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7693002

BQ7693003DBT ACTIVE TSSOP DBT 30 60 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7693003

BQ7693003DBTR ACTIVE TSSOP DBT 30 2000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7693003

BQ7693006DBT ACTIVE TSSOP DBT 30 60 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7693006

BQ7693006DBTR ACTIVE TSSOP DBT 30 2000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7693006

BQ7693007DBT ACTIVE TSSOP DBT 30 60 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7693007

PACKAGE OPTION ADDENDUM

www.ti.com 30-Sep-2017

Addendum-Page 2

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

BQ7693007DBTR ACTIVE TSSOP DBT 30 2000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7693007

BQ7694000DBT ACTIVE TSSOP DBT 44 40 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7694000

BQ7694000DBTR ACTIVE TSSOP DBT 44 2000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7694000

BQ7694001DBT ACTIVE TSSOP DBT 44 40 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7694001

BQ7694001DBTR ACTIVE TSSOP DBT 44 2000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7694001

BQ7694002DBT ACTIVE TSSOP DBT 44 40 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7694002

BQ7694002DBTR ACTIVE TSSOP DBT 44 2000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7694002

BQ7694003DBT ACTIVE TSSOP DBT 44 40 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7694003

BQ7694003DBTR ACTIVE TSSOP DBT 44 2000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7694003

BQ7694006DBT ACTIVE TSSOP DBT 44 40 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7694006

BQ7694006DBTR ACTIVE TSSOP DBT 44 2000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 BQ7694006

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance

do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may

reference these types of products as "Pb-Free".

RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based

flame retardants must also meet the <=1000ppm threshold requirement.

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

PACKAGE OPTION ADDENDUM

www.ti.com 30-Sep-2017

Addendum-Page 3

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

BQ7692000PWR TSSOP PW 20 2000 330.0 16.4 6.95 7.1 1.6 8.0 16.0 Q1

BQ7692003PWR TSSOP PW 20 2000 330.0 16.4 6.95 7.1 1.6 8.0 16.0 Q1

BQ7692006PWR TSSOP PW 20 2000 330.0 16.4 6.95 7.1 1.6 8.0 16.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 11-Apr-2016

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

BQ7692000PWR TSSOP PW 20 2000 367.0 367.0 38.0

BQ7692003PWR TSSOP PW 20 2000 367.0 367.0 38.0

BQ7692006PWR TSSOP PW 20 2000 367.0 367.0 38.0

PACKAGE MATERIALS INFORMATION

www.ti.com 11-Apr-2016

Pack Materials-Page 2

www.ti.com

PACKAGE OUTLINE

42X 0.5

10.5

44X 0.27

0.17

TYP

6.6

6.2

1.2 MAX

0.15

0.05

0.25

GAGE PLANE

-80

BNOTE 4

4.5

4.3

NOTE 3

11.1

10.9

0.75

0.50

(0.15) TYP

TSSOP - 1.2 mm max heightDBT0044A

SMALL OUTLINE PACKAGE

4220223/A 02/2017

22 23

0.08 C A B

PIN 1 INDEX

AREA

SEE DETAIL A

0.1 C

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing

per ASME Y14.5M.

2. This drawing is subject to change without notice.

3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not

exceed 0.15 mm per side.

4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.

SEATING

PLANE

A 20

DETAIL A

TYPICAL

SCALE 1.500

www.ti.com

EXAMPLE BOARD LAYOUT

0.05 MAX

ALL AROUND 0.05 MIN

ALL AROUND

44X (1.5)

44X (0.3)

42X (0.5)

(5.8)

(R0.05) TYP

TSSOP - 1.2 mm max heightDBT0044A

SMALL OUTLINE PACKAGE

4220223/A 02/2017

NOTES: (continued)

5. Publication IPC-7351 may have alternate designs.

6. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN

SCALE: 8X

SYMM

22 23

15.000

METAL

SOLDER MASK

OPENING METAL UNDER

SOLDER MASK SOLDER MASK

OPENING

EXPOSED METAL

SOLDER MASK DETAILS

NON-SOLDER MASK

DEFINED

(PREFERRED)

SOLDER MASK

DEFINED

www.ti.com

EXAMPLE STENCIL DESIGN

44X (1.5)

44X (0.3)

42X (0.5)

(5.8)

(R0.05) TYP

TSSOP - 1.2 mm max heightDBT0044A

SMALL OUTLINE PACKAGE

4220223/A 02/2017

NOTES: (continued)

7. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate

design recommendations.

8. Board assembly site may have different recommendations for stencil design.

SOLDER PASTE EXAMPLE

BASED ON 0.125 mm THICK STENCIL

SCALE: 8X

SYMM

22 23

IMPORTANT NOTICE

Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its

semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers

should obtain the latest relevant information before placing orders and should verify that such information is current and complete.

TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated

circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and

services.

Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is

accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced

documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements

different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the

associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers

remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have

full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products

used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with

respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous

consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and

take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will

thoroughly test such applications and the functionality of such TI products as used in such applications.

TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,

including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to

assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any

way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource

solely for this purpose and subject to the terms of this Notice.

TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI

products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,

enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically

described in the published documentation for a particular TI Resource.

Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that

include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE

TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY

RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or

endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR

REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO

ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL

PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,

INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF

PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,

DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN

CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949

and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.

Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such

products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards

and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must

ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in

life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.

Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life

support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all

medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.

TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).

Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications

and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory

requirements in connection with such selection.

Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-

compliance with the terms and provisions of this Notice.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Texas Instruments:

BQ7692006PWR BQ7692006PW BQ7692000PWR BQ7692000PW BQ7692003PW BQ7692003PWR