TPS726126 TPS72615, TPS72616 TPS72618, TPS72625 www.ti.com SLVS403H - MAY 2002 - REVISED JUNE 2010 LOW INPUT VOLTAGE, 1-A LOW-DROPOUT LINEAR REGULATORS WITH SUPERVISOR Check for Samples: TPS726126, TPS72615, TPS72616, TPS72618, TPS72625 FEATURES 1 * * * * * * * * * * 1-A Low-Dropout Regulator Supports Input Voltages Down to 1.8-V Available in 1.26-V, 1.5-V, 1.6-V, 1.8-V, 2.5-V Stable With Any Type/Value Output Capacitor 2% Output Voltage Tolerance Over Line, Load, and Temperature (-40C to +125C) Integrated Supervisor (SVS) With 200-ms RESET Delay Time Low 170-mV Dropout Voltage at 1 A (TPS72625) Low 210-mA Ground Current at Full Load Less than 1-mA Standby Current Integrated UVLO with Thermal and Overcurrent Protection 5-Lead SOT223 or DDPAK Surface-Mount Package APPLICATIONS * * * * * PCI Cards Modem Banks and Telecom Boards DSP, FPGA, and Microprocessor Power Supplies Portable, Battery-Powered Applications 1.26-V Core Voltage for the Following DSPs: - TMS320vC5501 - TMS320vC5502 DESCRIPTION The TPS726xx family of 1-A low-dropout (LDO) linear regulators has fixed voltage options available that are commonly used to power the latest DSPs, FPGAs, and microcontrollers. The integrated supervisory circuitry provides an active low RESET signal when the output falls out of regulation. The no capacitor/any capacitor feature allows the customer to tailor output transient performance as needed. Therefore, compared to other regulators capable of providing the same output current, this family of regulators can provide a stand alone power supply solution or a post regulator for a switch mode power supply. These regulators operate over a wide range of input voltages (1.8 V to 6 V) and have very low dropout (170 mV at 1-A). Ground current is typically 210 A at full load and drops to less than 80 A at no load. Standby current is less than 1 A. Unlike some regulators that have a minimum current requirement, the TPS726xx family is stable with no output load current. The low noise capability of this family, coupled with its high current operation and ease of power dissipation, make it ideal for telecom boards, modem banks, and other noise sensitive applications. The TPS726xx is available in either a SOT223 or DDPAK package. The TPS726126 is available in a SOT223 package only. DCQ PACKAGE SOT223-5 (TOP VIEW) 1 2 3 4 5 1 2 3 4 5 ENABLE IN GND OUT RESET ENABLE IN GND OUT RESET KTT PACKAGE DDPAK (TOP VIEW) Note: Tab is GND for both packages 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2002-2010, Texas Instruments Incorporated TPS726126 TPS72615, TPS72616 TPS72618, TPS72625 SLVS403H - MAY 2002 - REVISED JUNE 2010 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) PRODUCT VOUT TPS726xx xyyy z (1) XXX is nominal output voltage (for example, 126 = 1.26V, 15 = 1.5V). YYY is package designator. Z is package quantity. For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted (1) UNIT Input voltage, VI (2) Voltage range at EN -0.3 to 7 V -0.3 to VI + 0.3 V VIN + 0.3 V 6 V 2 kV Voltage on RESET Voltage on OUT ESD rating, HBM Continuous total power dissipation See Dissipation Rating Table Operating junction temperature range, TJ -50 to 150 C Maximum junction temperature range, TJ 150 C -65 to 150 C Storage temperature, Tstg (1) (2) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to network ground terminal. PACKAGE DISSIPATION RATINGS (1) (2) 2 PACKAGE BOARD RqJC RqJA DDPAK High K (1) 2 C/W 23 C/W SOT223 Low K (2) 15 C/W 53 C/W The JEDEC high K (2s2p) board design used to derive this data was a 3-inch x 3-inch (7,5-cm x 7,5-cm), multilayer board with 1 ounce internal power and ground planes and 2 ounce copper traces on top and bottom of the board. The JEDEC low K (1s) board design used to derive this data was a 3-inch x 3-inch (7,5-cm x 7,5-cm), two-layer board with 2 ounce copper traces on top of the board. Submit Documentation Feedback Copyright (c) 2002-2010, Texas Instruments Incorporated Product Folder Link(s): TPS726126 TPS72615 TPS72616 TPS72618 TPS72625 TPS726126 TPS72615, TPS72616 TPS72618, TPS72625 www.ti.com SLVS403H - MAY 2002 - REVISED JUNE 2010 ELECTRICAL CHARACTERISTICS over recommended operating free-air temperature range VI = VO(typ) + 1 V, IO= 1 mA, EN = IN, CO = 1 F, CI = 1 F (unless otherwise noted). Typical values are at +25C. PARAMETER VI (1) IO TEST CONDITIONS Input voltage Continuous output current Bandgap voltage reference VO Output voltage I MIN 6 V 0 1 A V 1.177 1.220 1.263 1.222 1.26 1.298 1.8 V VI 5.5 V TPS72615 0 A < IO < 1 A 1.8 V VI 5.5 V 1.47 1.5 1.53 TPS72616 0 A < IO < 1 A 2.6 V VI 5.5 V 1.568 1.6 1.632 TPS72618 0 A < IO < 1 A 2.8 V VI 5.5 V 1.764 1.8 1.836 TPS72625 0 A < IO < 1 A 3.5 V VI 5.5 V 2.45 2.5 2.55 IO = 0 A 75 120 IO = 1 A 210 300 0.2 1 Standby current EN < 0.4 V Output noise voltage BW = 200 Hz to 100 kHz PSRR Ripple rejection f = 1 kHz, Co = 10 F Current limit (2) CO = 10 F 150 A dB 1.6 2.3 A Output voltage line regulation (VO/VO) (3) VO + 1 V < VI 5.5 V -0.15 0.02 0.15 %/V Output voltage load regulation 0 A < IO < 1 A -0.25 0.05 0.25 %/A EN high level input 1.3 EN low level input -0.2 II EN input current EN = 0 V or VI UVLO threshold VCC rising UVLO hysteresis VCC rising UVLO deglitch UVLO delay Dropout voltage (4) 1.45 0.4 0.01 100 1.57 1.70 V nA V 50 mV VCC rising 10 s VCC rising 100 s TPS72625 IO = 1 A 170 280 TPS72618 IO = 1 A 210 320 Minimum input voltage for valid RESET (VRES) 1.3 Trip threshold voltage 90 Hysteresis voltage t(RESET) delay time 100 Output low voltage (at 700 A) 93 96 Leakage current Operating junction temperature 200 -40 %VO mV 300 10 -0.3 mV V 10 Rising edge deglitch (4) A 1.1 VIL (1) (2) (3) V V 60 VIH TJ UNIT 1.8 0 A < IO < 1 A Vn RESET MAX TPS726126 Ground current VDO TYP ms s 0.4 V 100 nA +125 C Minimum VIN is 1.800 V or VO + VDO, whichever is greater. Test condition includes, output voltage VO = VO - 15% and pulse duration = 10 ms. VImin = (VO + 1) or 1.8 V whichever is greater. VO5.5 V * V Imin Line regulation (mV) + (%V) 1000 100 Dropout voltage is defined as the differential voltage between VO and VI when VO drops 100 mV below the value measured with VI = VO + 1 V. Copyright (c) 2002-2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS726126 TPS72615 TPS72616 TPS72618 TPS72625 3 TPS726126 TPS72615, TPS72616 TPS72618, TPS72625 SLVS403H - MAY 2002 - REVISED JUNE 2010 www.ti.com FUNCTIONAL BLOCK DIAGRAM TPS726126/15/16 IN OUT EN Current Limit / Thermal Protection 1.220 Vref GND RESET Deglitch and Delay 0.93 x Vref Terminal Functions TERMINAL NAME NO. DESCRIPTION GND 3 Ground ENABLE 1 Enable input IN 2 Input supply voltage RESET 5 This terminal is the RESET output. When used with a pull-up resistor, this open-drain output provides the active low RESET signal when the regulator output voltage drops more than 5% below its nominal output voltage. The RESET delay time is typically 200 ms. OUT 4 Regulated output voltage RESET TIMING DIAGRAM IN VRES (see Note A) VRES t OUT VIT + VIT + Threshold Voltage VIT - I I I I I I RESET Output Output Undefined VIT - t 200 ms Delay 200 ms Delay Submit Documentation Feedback Output Undefined t NOTES:A. VRES is the minimum input voltage for a valid RESET. 4 I I I I I I Copyright (c) 2002-2010, Texas Instruments Incorporated Product Folder Link(s): TPS726126 TPS72615 TPS72616 TPS72618 TPS72625 TPS726126 TPS72615, TPS72616 TPS72618, TPS72625 www.ti.com SLVS403H - MAY 2002 - REVISED JUNE 2010 TYPICAL CHARACTERISTICS TPS72618 OUTPUT VOLTAGE vs JUNCTION TEMPERATURE TPS72618 OUTPUT VOLTAGE vs OUTPUT CURRENT 250 1.805 1.8015 V O - Output Voltage - V 1.8005 1.8 1.7995 Ground Current - A VI = 2.8 V Co = 1 F VI = 2.8 V Co = 1 F TJ = 25 C 1.801 V O - Output Voltage - V TPS72618 GROUND CURRENT vs JUNCTION TEMPERATURE 1.800 IO = 0 mA 1.795 IO = 1 A 1.790 IO = 1 A 150 IO = 0 mA 100 50 1.799 1.785 -40-25 -10 5 20 35 50 65 80 95 110 125 TJ - Junction Temperature - C 1.7985 0.2 0.4 0.6 0.8 1 IO - Output Current - A 20 35 50 65 80 95 110 125 TJ - Junction Temperature - C Figure 1. Figure 2. Figure 3. TPS72618 GROUND CURRENT vs OUTPUT CURRENT TPS72625 DC DROPOUT VOLTAGE vs OUTPUT CURRENT TPS72618 DROPOUT VOLTAGE vs JUNCTION TEMPERATURE 300 200 300 VO = 2.5 V (nom) 175 V DO - Dropout Voltage - mV 250 150 125 100 75 50 25 0 0.01 0 -40 -25 -10 5 V DO - Dropout Voltage - mV 0 Ground Current - A 200 VI = 2.8 V Co = 1 F TJ = 25 C TJ = 125C 200 TJ = 25C 150 100 TJ = -40C 50 0 0.1 1 10 100 1000 IO - Output Current - mA Figure 4. Copyright (c) 2002-2010, Texas Instruments Incorporated 0 0.2 0.4 0.6 0.8 IO - Output Current - A 1 250 VO = 1.7 V Co = 1 F IO = 1 A 200 150 100 50 IO = 10 mA 0 -40 -25 -10 5 20 35 50 65 80 95 110 125 TJ - Junction Temperature - C Figure 5. Figure 6. Submit Documentation Feedback Product Folder Link(s): TPS726126 TPS72615 TPS72616 TPS72618 TPS72625 5 TPS726126 TPS72615, TPS72616 TPS72618, TPS72625 SLVS403H - MAY 2002 - REVISED JUNE 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) MINIMUM REQUIRED INPUT VOLTAGE vs OUTPUT VOLTAGE TJ = 125C TJ = 25C 2.5 TJ = -40C 2 1.5 2 2.5 3 3.5 4 4.5 -100 0 50 100 150 200 250 300 350 400 450 500 -100 1 0.5 0 0 5 t - Time - s 10 15 20 25 30 35 40 45 50 t - Time - s Figure 9. TPS72618 LOAD TRANSIENT RESPONSE TPS72618 OUTPUT VOLTAGE, ENABLE VOLTAGE vs TIME (START-UP) TPS72618 POWER UP/POWER DOWN -100 VI = 2.8 V Co = 1 F CI = 1 F 1 0.5 0 10 15 20 25 30 35 40 t - Time - s 45 50 Figure 10. Submit Documentation Feedback 3 VI - Input Voltage - V 0 5 0 0 Figure 8. 100 0 100 VO = 2.8 V Co = 10 F Ci = 1 F 100 Figure 7. Enable Voltage - V VO - Change in I O - Output Current - A Output Voltage - mV VO - Output Voltage - V VO - Output Voltage - mV 3 1.5 6 2.8 VI = 2.8 V IO = 1 A Co = 10 F 2 1 0 2 1.5 1 0.5 0 0 20 40 60 80 100 120 140 160 180 200 t - Time - s VO - Output Voltage - V 3.5 IO = 1 A Co = 10 F 3.8 I O - Output Current - A VI - Input Voltage - V 4 V - Output Voltage - V O V I - Minimum Required Input Voltage - V 4.5 TPS72618 LOAD TRANSIENT RESPONSE VO - Change in Output Voltage - mV TPS72618 LINE TRANSIENT RESPONSE 5 4 3 RL = 1.8 Co = 1 F Ci = 1 F VI 2 1 0 VO 0 100 200 300 400 500 600 700 800 900 1000 Figure 11. t - Time - s Figure 12. Copyright (c) 2002-2010, Texas Instruments Incorporated Product Folder Link(s): TPS726126 TPS72615 TPS72616 TPS72618 TPS72625 TPS726126 TPS72615, TPS72616 TPS72618, TPS72625 www.ti.com SLVS403H - MAY 2002 - REVISED JUNE 2010 TYPICAL CHARACTERISTICS (continued) TPS72618 RIPPLE REJECTION vs FREQUENCY 2.5 2000 VI= 2.8 V, VO = 1.8 V, CO = 10 F 90 2 IO = 1 A 1.5 1 80 60 10 F / 1mA 50 IO = 1 mA 40 30 10 F / 1A 10 100 1k 10 k f - Frequency - Hz 1500 TJ = 25C 1400 TJ = -40C 1300 1100 10 Figure 13. 100 1k 10 k 100 k 1M 2 2.5 3 3.5 4 4.5 f - Frequency - Hz VI - Input voltage - V Figure 14. Figure 15. TPS72615 GROUND CURRENT vs INPUT VOLTAGE 5 5.5 DROPOUT VOLTAGE vs INPUT VOLTAGE 600 300 500 250 V DO - Dropout Voltage - mV Ground Current - A 1600 1000 1.5 0 100 k 1700 1200 10 0 TJ = 125C 1800 70 20 0.5 1900 Current Limit - A 3 CURRENT LIMIT vs INPUT VOLTAGE 100 VI = 2.8 V Co = 10 F Ripple Rejection - dB V/ 3.5 Output Spectral Noise Density - Hz TPS72618 OUTPUT SPECTRAL NOISE DENSITY vs FREQUENCY 400 300 I=1A 200 I=0A 100 0 TJ = 125C TJ = 25C 200 150 100 TJ = -40C 50 0 0 1 2 3 4 5 VI - Input Voltage - V Figure 16. Copyright (c) 2002-2010, Texas Instruments Incorporated 6 1.5 2 2.5 3 3.5 4 4.5 VI - Input Voltage - V 5 5.5 Figure 17. Submit Documentation Feedback Product Folder Link(s): TPS726126 TPS72615 TPS72616 TPS72618 TPS72625 7 TPS726126 TPS72615, TPS72616 TPS72618, TPS72625 SLVS403H - MAY 2002 - REVISED JUNE 2010 www.ti.com APPLICATION INFORMATION The TPS726xx family of low-dropout (LDO) regulators have numerous features that make it apply to a wide range of applications. The family operates with very low input voltage (1.8 V) and low dropout voltage (typically 200 mV at full load), making it an efficient stand-alone power supply or post regulator for battery or switch mode power supplies. Both the active low RESET and 1-A output current, make the TPS726xx family ideal for powering processor and FPGA supplies. The TPS726xx family also has low output noise (typically 150 VRMS with 10-F output capacitor), making it ideal for use in telecom equipment. External Capacitor Requirements A 1-F or larger ceramic input bypass capacitor, connected between IN and GND and located close to the TPS726xx, is required for stability. To improve transient response, noise rejection, and ripple rejection, an additional 10-F or larger, low ESR capacitor is recommended. A higher-value, low ESR input capacitor may be necessary if large, fast-rise-time load transients are anticipated and the device is located several inches from the power source, especially if the minimum input voltage of 1.8 V is used. Although an output capacitor is not required for stability, transient response and output noise are improved with a 10-F output capacitor. TPS726xx VI IN VO OUT 1 mF 10 kW EN CO RESET GND Figure 18. TPS726xx Fixed Output Typical Application Diagram Regulator Protection The TPS726xx pass element has a built-in back diode that safely conducts reverse current when the input voltage drops below the output voltage (e.g., during power down). Current is conducted from the output to the input and is not internally limited. If extended reverse voltage is anticipated, external limiting might be appropriate. The TPS726xx also features internal current limiting and thermal protection. During normal operation, the TPS726xx limits output current to approximately 1.6 A. When current limiting engages, the output voltage scales back linearly until the overcurrent condition ends. While current limiting is designed to prevent gross device failure, care should be taken not to exceed the power dissipation ratings of the package. If the temperature of the device exceeds 165C, thermal-protection circuitry shuts it down. Once the device has cooled down to below 145C, regulator operation resumes. THERMAL INFORMATION The amount of heat that an LDO linear regulator generates is directly proportional to the amount of power it dissipates during operation. All integrated circuits have a maximum allowable junction temperature (TJmax) above which normal operation is not assured. A system designer must design the operating environment so that the operating junction temperature (TJ) does not exceed the maximum junction temperature (TJmax). The two main environmental variables that a designer can use to improve thermal performance are air flow and external heatsinks. The purpose of this information is to aid the designer in determining the proper operating environment for a linear regulator that is operating at a specific power level. 8 Submit Documentation Feedback Copyright (c) 2002-2010, Texas Instruments Incorporated Product Folder Link(s): TPS726126 TPS72615 TPS72616 TPS72618 TPS72625 TPS726126 TPS72615, TPS72616 TPS72618, TPS72625 www.ti.com SLVS403H - MAY 2002 - REVISED JUNE 2010 In general, the maximum expected power (PD(max)) consumed by a linear regulator is computed as: P max + V *V D I(avg) O(avg) I ) V O(avg) I(avg) xI (Q) (1) Where: * VI(avg) is the average input voltage. * VO(avg) is the average output voltage. * O(avg) is the average output current. * I(Q) is the quiescent current. For most TI LDO regulators, the quiescent current is insignificant compared to the average output current; therefore, the term VI(avg) x I(Q) can be neglected. The operating junction temperature is computed by adding the ambient temperature (TA) and the increase in temperature due to the regulator's power dissipation. The temperature rise is computed by multiplying the maximum expected power dissipation by the sum of the thermal resistances between the junction and the case (R)qJC), the case to heatsink (R)qCS), and the heatsink to ambient (R)qSA). Thermal resistances are measures of how effectively an object dissipates heat. Typically, the larger the device, the more surface area available for power dissipation and the lower the object's thermal resistance. Figure 19 illustrates these thermal resistances for (a) a SOT223 package mounted in a JEDEC low-K board, and (b) a DDPAK package mounted on a JEDEC high-K board. A TJ RJC CIRCUIT BOARD COPPER AREA C B B A B TC RCS A C RSA SOT223 Package (a) TA DDPAK Package (b) C Figure 19. Thermal Resistances Equation 2 summarizes the computation: T J + T ) PDmax x R ) R ) R A JC CS SA (2) The RqJC is specific to each regulator as determined by its package, lead frame, and die size provided in the regulator's data sheet. The RqSA is a function of the type and size of heatsink. For example, black body radiator type heatsinks can have RqCS values ranging from 5C/W for very large heatsinks to 50C/W for very small heatsinks. The RqCS is a function of how the package is attached to the heatsink. For example, if a thermal compound is used to attach a heatsink to a SOT223 package, RqCSof 1C/W is reasonable. Even if no external black body radiator type heatsink is attached to the package, the board on which the regulator is mounted provides some heatsinking through the pin solder connections. Some packages, like the DDPAK and SOT223 packages, use a copper plane underneath the package or the circuit board's ground plane for additional heatsinking to improve their thermal performance. Computer-aided thermal modeling can be used to compute very accurate approximations of an integrated circuit's thermal performance in different operating environments (e.g., different types of circuit boards, different types and sizes of heatsinks, and different air flows, etc.). Using these models, the three thermal resistances can be combined into one thermal resistance between junction and ambient (R)qJA). This RqJAis valid only for the specific operating environment used in the computer model. Copyright (c) 2002-2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS726126 TPS72615 TPS72616 TPS72618 TPS72625 9 TPS726126 TPS72615, TPS72616 TPS72618, TPS72625 SLVS403H - MAY 2002 - REVISED JUNE 2010 www.ti.com Equation 2 simplifies into Equation 3: T + T ) PDmax x R J A JA (3) Rearranging Equation 3 gives Equation 4: T -T R + J A JA P max D (4) Using Equation 3 and the computer model generated curves shown in Figure 20 and Figure 23, a designer can quickly compute the required heatsink thermal resistance/board area for a given ambient temperature, power dissipation, and operating environment. DDPAK Power Dissipation The DDPAK package provides an effective means of managing power dissipation in surface mount applications. The DDPAK package dimensions are provided in the Mechanical Data section at the end of the data sheet. The addition of a copper plane directly underneath the DDPAK package enhances the thermal performance of the package. To illustrate, the TPS72625 in a DDPAK package was chosen. For this example, the average input voltage is 5 V, the output voltage is 2.5 V, the average output current is 1 A, the ambient temperature 55C, the air flow is 150 LFM, and the operating environment is the same as documented below. Neglecting the quiescent current, the maximum average power is: P Dmax + (5 * 2.5) V x 1 A + 2.5 W (5) Substituting TJmax for TJ into Equation 4 gives Equation 6: R max + (125 * 55)C2.5 W + 28CW JA (6) 2 From Figure 20, DDPAK Thermal Resistance vs Copper Heatsink Area, the ground plane needs to be 1 cm for the part to dissipate 2.5 W. The operating environment used in the computer model to construct Figure 20 consisted of a standard JEDEC High-K board (2S2P) with a 1 oz. internal copper plane and ground plane. The package is soldered to a 2 oz. copper pad. The pad is tied through thermal vias to the 1 oz. ground plane. Figure 21 shows the side view of the operating environment used in the computer model. 40 R JA - Thermal Resistance - C/W No Air Flow 35 150 LFM 30 250 LFM 25 20 15 0.1 1 10 Copper Heatsink Area - cm2 100 Figure 20. DDPAK Thermal Resistance vs Copper Heatsink Area 10 Submit Documentation Feedback Copyright (c) 2002-2010, Texas Instruments Incorporated Product Folder Link(s): TPS726126 TPS72615 TPS72616 TPS72618 TPS72625 TPS726126 TPS72615, TPS72616 TPS72618, TPS72625 www.ti.com SLVS403H - MAY 2002 - REVISED JUNE 2010 2 oz. Copper Solder Pad with 25 Thermal Vias 1 oz. Copper Power Plane 1 oz. Copper Ground Plane Thermal Vias, 0,3 mm Diameter, 1,5 mm Pitch Figure 21. DDPAK Thermal Resistance From the data in Figure 22 and rearranging Equation 4, the maximum power dissipation for a different ground plane area and a specific ambient temperature can be computed. TJM - Maximum Junction Temperature - 125 C 5 PD - Maximum Power Dissipation - W TA = 55C 4 250 LFM 150 LFM 3 No Air Flow 2 1 0.1 1 10 Copper Heatsink Area - cm2 100 Figure 22. Maximum Power Dissipation vs Copper Heatsink Area SOT223 Power Dissipation The SOT223 package provides an effective means of managing power dissipation in surface mount applications. The SOT223 package dimensions are provided in the Mechanical Data section at the end of the data sheet. The addition of a copper plane directly underneath the SOT223 package enhances the thermal performance of the package. To illustrate, the TPS72625 in a SOT223 package was chosen. For this example, the average input voltage is 3.3 V, the output voltage is 2.5 V, the average output current is 1 A, the ambient temperature 55C, no air flow is present, and the operating environment is the same as documented below. Neglecting the quiescent current, the maximum average power is: P Dmax + (3.3 * 2.5) V x 1 A + 800 mW (7) Substituting TJmax for TJ into Equation 4 gives Equation 8: Copyright (c) 2002-2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS726126 TPS72615 TPS72616 TPS72618 TPS72625 11 TPS726126 TPS72615, TPS72616 TPS72618, TPS72625 SLVS403H - MAY 2002 - REVISED JUNE 2010 R JA www.ti.com max + (125 * 55)C800 mW + 87.5CW (8) 2 From Figure 23, RqJA vs PCB Copper Area, the ground plane needs to be 0.55 in for the part to dissipate 800 mW. The operating environment used to construct Figure 23 consisted of a board with 1 oz. copper planes. The package is soldered to a 1 oz. copper pad on the top of the board. The pad is tied through thermal vias to the 1 oz. ground plane. R JA - Thermal Resistance - C/W 180 No Air Flow 160 140 120 100 80 60 40 20 0 0.1 1 PCB Copper Area - in2 10 Figure 23. SOT223 Thermal Resistance vs PCB AREA From the data in Figure 23 and rearranging Equation 4, the maximum power dissipation for a different ground plane area and a specific ambient temperature can be computed (as shown in Figure 24). 6 PD - Maximum Power Dissipation - W TA = 25C 5 4 4 in2 PCB Area 3 0.5 in2 PCB Area 2 1 0 0 25 50 75 100 125 150 TA - Ambient Temperature - C Figure 24. SOT223 Power Dissipation 12 Submit Documentation Feedback Copyright (c) 2002-2010, Texas Instruments Incorporated Product Folder Link(s): TPS726126 TPS72615 TPS72616 TPS72618 TPS72625 TPS726126 TPS72615, TPS72616 TPS72618, TPS72625 www.ti.com SLVS403H - MAY 2002 - REVISED JUNE 2010 REVISION HISTORY NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision G (May 2006) to Revision H Page * Deleted Figure 14, Output Impedance vs Frequency ........................................................................................................... 7 * Added Figure 18 ................................................................................................................................................................... 8 Copyright (c) 2002-2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS726126 TPS72615 TPS72616 TPS72618 TPS72625 13 PACKAGE OPTION ADDENDUM www.ti.com 25-Jan-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) (Requires Login) TPS726126DCQ ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS726126DCQG4 ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS726126DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS726126DCQRG4 ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72615DCQ ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72615DCQG4 ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72615DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72615DCQRG4 ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72615KTT OBSOLETE DDPAK/ TO-263 KTT 5 TPS72615KTTR ACTIVE DDPAK/ TO-263 KTT 5 TPS72615KTTRG3 ACTIVE DDPAK/ TO-263 KTT TPS72615KTTT ACTIVE DDPAK/ TO-263 TPS72615KTTTG3 ACTIVE TPS72616DCQ TBD Call TI Call TI 500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR 5 500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR KTT 5 50 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR DDPAK/ TO-263 KTT 5 50 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72616DCQG4 ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72616DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72616DCQRG4 ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Jan-2012 Status (1) Package Type Package Drawing Pins TPS72616KTT OBSOLETE DDPAK/ TO-263 KTT 5 TPS72616KTTR ACTIVE DDPAK/ TO-263 KTT 5 TPS72616KTTRG3 ACTIVE DDPAK/ TO-263 KTT TPS72616KTTT ACTIVE DDPAK/ TO-263 TPS72616KTTTG3 ACTIVE TPS72618DCQ Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) TBD Call TI Call TI 500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR 5 500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR KTT 5 50 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR DDPAK/ TO-263 KTT 5 50 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72618DCQG4 ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72618DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72618DCQRG4 ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72618KTT OBSOLETE DDPAK/ TO-263 KTT 5 TPS72618KTTR ACTIVE DDPAK/ TO-263 KTT 5 TPS72618KTTRG3 ACTIVE DDPAK/ TO-263 KTT TPS72618KTTT ACTIVE DDPAK/ TO-263 TPS72618KTTTG3 ACTIVE TPS72625DCQ TBD Call TI Call TI 500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR 5 500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR KTT 5 50 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR DDPAK/ TO-263 KTT 5 50 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72625DCQG4 ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72625DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS72625DCQRG4 ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Addendum-Page 2 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Jan-2012 Status (1) Package Type Package Drawing Pins TPS72625KTT OBSOLETE DDPAK/ TO-263 KTT 5 TPS72625KTTR ACTIVE DDPAK/ TO-263 KTT 5 TPS72625KTTRG3 ACTIVE DDPAK/ TO-263 KTT TPS72625KTTT ACTIVE DDPAK/ TO-263 TPS72625KTTTG3 ACTIVE DDPAK/ TO-263 Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) TBD Call TI Call TI 500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR 5 500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR KTT 5 50 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR KTT 5 50 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) TPS726126DCQR SOT-223 DCQ 6 2500 330.0 12.4 7.3 1.88 8.0 12.0 Q3 TPS72615DCQR SOT-223 DCQ 6 2500 330.0 12.4 TPS72615KTTR DDPAK/ TO-263 KTT 5 500 330.0 24.4 6.8 7.3 1.88 8.0 12.0 Q3 10.6 15.6 4.9 16.0 24.0 Q2 TPS72615KTTT DDPAK/ TO-263 KTT 5 50 330.0 24.4 10.6 15.6 4.9 16.0 24.0 Q2 TPS72616DCQR SOT-223 DCQ 6 2500 330.0 12.4 TPS72616KTTR DDPAK/ TO-263 KTT 5 500 330.0 24.4 6.8 7.3 1.88 8.0 12.0 Q3 10.6 15.6 4.9 16.0 24.0 Q2 TPS72616KTTT DDPAK/ TO-263 KTT 5 50 330.0 24.4 10.6 15.6 4.9 16.0 24.0 Q2 TPS72618DCQR SOT-223 DCQ 6 2500 330.0 12.4 6.8 7.3 1.88 8.0 12.0 Q3 TPS72618KTTR DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.6 15.6 4.9 16.0 24.0 Q2 TPS72618KTTT DDPAK/ TO-263 KTT 5 50 330.0 24.4 10.6 15.6 4.9 16.0 24.0 Q2 TPS72625DCQR SOT-223 DCQ TPS72625KTTR DDPAK/ TO-263 KTT 6 2500 330.0 12.4 6.8 7.3 1.88 8.0 12.0 Q3 5 500 330.0 24.4 10.6 15.6 4.9 16.0 24.0 Q2 TPS72625KTTT DDPAK/ KTT 5 50 330.0 24.4 10.6 15.6 4.9 16.0 24.0 Q2 Pack Materials-Page 1 6.8 W Pin1 (mm) Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TO-263 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS726126DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TPS72615DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TPS72615KTTR DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 TPS72615KTTT DDPAK/TO-263 KTT 5 50 367.0 367.0 45.0 TPS72616DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TPS72616KTTR DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 TPS72616KTTT DDPAK/TO-263 KTT 5 50 367.0 367.0 45.0 TPS72618DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TPS72618KTTR DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 TPS72618KTTT DDPAK/TO-263 KTT 5 50 367.0 367.0 45.0 TPS72625DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TPS72625KTTR DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 TPS72625KTTT DDPAK/TO-263 KTT 5 50 367.0 367.0 45.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated