Q68100A0991 - OSRAM OPTO SEMICONDUCTORS

Lead (Pb) Free Product - RoHS Compliant

Standar d Red SCD55100A

Yellow SCD55101A

High Efficiency Red SCD55102A

Green SCD55103A

High Efficiency Green SCD55104A

limline

0.145’’ 10-Character 5x5 Dot Matrix Serial Input

Dot Addressable Intelligent Display® Devices

2008-07-22 1

DESCRIPTION

The SCD55100A (Red), SCD55101A (Yellow),

SCD55102A (HER), SCD55103A (Green) and

SCD55104A (HEG) are eight digit dot ad dressable 5 x 5

matrix, Serial Input, Intelligent Display devices.

The ten 3.68 mm (0.145") high digits are pac kaged in a

rugged, high quality optically transparent, standard

7.62 mm (0.3") pin spacing 28 pin plastic DIP.

The on-board CMOS has a 250 bit RAM, one bit associ-

ated with one LED, each to generate User Defined Char-

acters. Due to the reduced LED count, power

requirement and heat dissipation are reduced by 30%.

Additionally in Power Down Mod e quiescent current

is <50 µA.

The SCD5510XA is des igned to work with the Serial port

of most common microprocessors. The multiplex Clock

I/O (CLK I/O) and multiplex Clock Select (CLKSEL) pins

offer the user the capability to supply a high speed

external multiplex clock . This feature can minimize audio

in-band interference for portable communication

equipment or eliminate the visual syn chronization eff ects

found in high vibration environments such as avionics

equipment.

FEATURES

• Low Profile Package: 60% Smaller than Industry Stan-

dard 10-Digit Display

• Ten 3.68 mm (0.145") 5 x 5 Dot Matrix Characters

in Red, Yellow, High Efficiency Red, Green, or

High Efficiency Green

• Optimum Display Surface Efficiency

(display area to package ratio)

• Low Pow er–30% Less Power Dissipation

than 5 x 7 Format

• High Speed Data Input Rate: 5.0 MHz

• ROMless Serial Input, Dot Addressable

Display—Ideal for User Defined Characters

• Built-in De c od e r s, Multiplexers and LED Drivers

• Readable from 1.8 meters (6 Feet)

• Wide Viewing Angle, X Axis ± 55°, Y Axis ± 65°

• Attributes:

– 250 bit RAM for User Defined Characters

– Eight Dimming Levels

– Power Down Mode (<25 0 µW)

– Hardware/Software Clear Function

– Lamp Test

• Internal or External Clock

• End-Stackable Dual-in-line Plastic Package

– 3.3 V Capability

2008-07-22 2

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

Packag e Ou tlines Dimensions in mm (inch)

Ordering Information

Type Color of Emission Character Height

mm (inch) Ordering Code

SCD55104A standard red

3.68 (0.145)

Q68100A0988

SCD55101A yellow Q68100A0989

SCD55102A high efficiency red Q68100A0990

SCD55103A green Q68100A0991

SCD55104A high efficiency gree n Q68100A0992

IDOD5211

2.03 (0.080) 3.81 (0.150)

38.1 (1.500) max.

3.68 (0.145)

5.08 (0.200)

7.62 (0.300)

±0.51 (0.020)

10 (0.394)

±0.15 (0.006)

0.3 (0.012) typ.

1.27 (0.050) typ.

Indicator

4.06 (0.160)

±0.51 (0.020)

33.02 (1.300) ref.

Seating Plane

2.54 (0.100) typ.

±0.25 (0.010)

Tol. non accum.

SCD5510XA

OSRAM YYWW ZY

EIA Date Code Intensity Code

Hue Code

Dimension is at Seating Plane.

2. Display matrix and pins centered on package outline.

3. Display matrix centered to pin array.

4. Tolerance: ±.XXX (0.010)

Color Code

Part No

5. Lead dim .018 wide x .012 THK

0.25 (0.010)

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

2008-07-22 3

Maximum Ratings

Parameter Symbol Value Unit

Operating temperature range Top – 40 … + 85 °C

Storage temperature range Tstg – 40 … + 100 °C

DC Supply Voltage VCC -0.5 to + 7.0 V

Input Voltage Levels Relative to GND -0.5 to VCC to 0.5 V

Solder Temperature

1.59 mm (0.063“) below seating plane, t < 5.0 s TS260 °C

Relative Humidity 85 %

ESD (100 pF, 1.5 kΩ) VZ2.0 kV

Input Current ± 100 mA

Power Dissipation at 85°C 1.7 W

Maximum Number of LEDs on at 100% Brightness 160

IC Junction Temperature 125 °C

Optical Characteristics at 25°C

(VCC=5.0 V at 100% brightness level, viewing angle: X axis ± 55°, Y axis ± 65°)

Description Symbol Values Unit

Red

SCD55100A

Yellow

SCD55101A

High Efficiency Red

SCD55102A

Green

SCD55103A

High Efficiency Green

SCD55104A

Luminous Intensity (min.)

(typ.) IV36

78 124

208 124

237 124

238 124

500 µcd/dot

µcd/dot

Peak Wavelength (typ.) λpeak 665 583 630 565 568 nm

Dominant Wavelength (typ.) λdom 639 584 626 569 572 nm

Notes:

1. Dot to dot intensity matching at 100% brightness is 1.8:1.

2. Displays are binned for hue at 2.0 nm intervals.

3. Displays within a given intensity category have an intensity matching of 1.5:1 (max.).

2008-07-22 4

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

Data Write Cycle

Instruction Cycle

Maximum Power Dissipation vs. Temperature

OAD

DATA

SDCLK

TSDCW

TSDCLK Period

TLDS

TDS TDH

TLDH

3.5 V

1.5 V

3.5 V

1.5 V

3.5 V

1.5 V

TSDCW

TWR

LOAD

SDCLK

DATA

LOAD

SDCLK

DATA

TBL

D0D7D6D5D4D3D2D1D0

IDDG5332

-40

˚C

1.0

2.0

3.0

4.0

= 31 ˚C/W

0.5

1.5

2.5

3.5

-20 0 20 40 60 100

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

2008-07-22 5

Input/Output Circuits

Figures „Inputs“ and „Clock I/O“ show the input and output resis-

tor/diode networks used for ESD protection and to eliminate sub-

strate latch-up caused by input voltage over/under shoot.

Inputs

Top View

Clock I/O

Electrical Characteristics (over operating temperature)

Parameter Min. Typ. Max. Units Conditions

VCC 4.5 5.0 5.5 V —

ICC (Pwr Dwn Mode) (4) —50 —μAVCC=5.0 V, all inputs=0 V or VCC

ICC 10 digits 16 dots/character —250 365 mA VCC=5.0 V, “#” displayed in all 10 digits

at 100% brightness at 25°C

IIL Input current — — –10 μAVCC=5.0 V, VIN=0 V (all inputs)

IIH Input current — — 10 μAVCC=VIN=5.0 V (all inputs)

VIH 3.5 ——V VCC=4.5 V to 5.5 V

VIL — — 1.5 VVCC=4.5 V to 5.5 V

IOH (CLK I/O) —–8.9 —mA VCC=4.5 V, VOH=2.4 V

IOL (CLK I/O) —1.6 —mA VCC=4.5 V, VOL=0.4 V

θJA — — 31 °C/W —

Fext External Clock Input Frequency 120 —347 kHz VCC=5.0 V, CLKSEL=0

Fosc Internal Clock Input Frequency 120 —347 kHz VCC=5.0 V, CLKSEL=1

Clock I/O Bus Loading — — 240 pF —

Clock Out Rise Time — — 500 ns VCC=4.5 V, VOH=2.4 V

Clock Out Fall Time — — 500 ns VCC=4.5 V, VOH=0.4 V

FM, Digit 375 768 1086 Hz —

Notes:

1) Peak current 5/3 x ICC.

2) Unused inputs must be tied high.

3) Contact Infineon for 3.3 V operation.

4) External oscillator must be stopped if being used to maintain an ICC <50 μA.

IDCD5021

GND

1 k

Input

114

28 15

IDPA5117

IDCD5026

GND

1 kΩInput/Output

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

2008-07-22 6

Dot Matrix Format mm (inch)

Pin Assignment

Pin Function Pin Function

1SDCLK 28 GND

2LOAD 27 DATA

3NP 26 NP

4NP 25 NP

5NP 24 NP

6NP 23 NP

7NP 22 NP

8NP 21 NP

9NP 20 NP

10 NP 19 VCC

11 NP 18 NC

12 NP 17 NP

13 RST 16 CLKSEL

14 GND 15 CLK I/O

Switching Specifications

(over operating tempe r a ture r a nge and VCC=4.5 V to 5.5 V)

Symbol Description Min. Units

TRC Reset Active Time 600 ns

TLDS Load Setup Time 50 ns

TDS Data Setup Time 50 ns

TSDCLK Clock Period 200 ns

TSDCW Clock Width 70 ns

TLDH Load Hold Time 0ns

TDH Data Hold Time 25 ns

TWR Total Write Time 2.2 μs

TBL Time Between Loads 600 ns

Note: TSDCW is the minimum time the SDCLK may be low or high.

The SDCLK period must be a minimum of 200 ns.

IDOD5212

C0 C1 C2 C3 C4 R0

0.28 (0.011) typ. 0.84 (0.033) typ.

0.56 (0.022) typ.

3.68 (0.145)

2.03 (0.080)

Tolerance: ±0.25 (0.010)

Pin Definitions

Pin Function Definitions

1SDCLK Loads data into the 8-bit serial data register

on a low to high transition.

2LOAD Low input enables data clocking into 8-bit

serial shift register. When LOAD goes high,

the contents of 8-bit serial Shift Register will

be decoded.

3NP No Pin

4NP No Pin

5NP No Pin

6NP No Pin

7NP No pin

8NP No pin

9NP No Pin

10 NP No Pin

11 NP No Pin

12 NP No Pin

13 RST Asynchronous input, when low will clear the

Multiplex Counter, User RAM and Data

100% brightness and the Address Register is

set to select Digit 0. The display is blanked.

14 GND Power supply ground

15 CLK I/O Outputs master clock or inputs ex ternal clock.

16 CLKSEL H=internal clock, L=external clock

17 NP No Pin

18 NC No connection

19 VCC Power supply/heat sink

20 NP No Pin

21 NP No pin

22 NP No pin

23 NP No Pin

24 NP No Pin

25 NP No Pin

26 NP No Pin

27 DATA Serial data input

28 GND Power supply ground

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

2008-07-22 7

Operation of the SCD5510XA

The SCD5510XA d is pl ay consists of a C MOS IC co ntaining contr o l

logic and drivers for eight 5 x 5 characte rs . The se com pon ent s are

assembled in a compact (38 mm x 10 mm) pl asti c package.

Individual LED dot addressablity allows the user great freedom in

creating special characters or mini-icons. The User Definable

Character Set Examples illustr ate 200 diff erent char acter and sym -

bol possibilities.

The use of a serial data interface provides a highly efficient inter-

connection between the display and the mother board. The

SCD5510XA requires only 4 lines as compared to 15 for an equiv-

alent 8 character parallel input part.

The on-board CMOS IC is the electronic hear t of the display. The

IC accepts decoded serial data, which is stored in the internal RAM.

Asynchronously the RAM is read by the character multiplexer at a

strobe rate that results in a flicker free display. Figure „Row and

Column Location“ (page 9) sho ws the t hree function al ar eas o f the

IC. These include: the input serial data register and control logic, a

250 bits two port RAM, and an internal multiplexer/display driver.

SCD5510XA Block Diagram

Display Column and Row Format

C0 C1 C2 C3 C4

Row 0 1 1 1 1 1

Row 1 0 0 1 0 0

Row 2 0 0 1 0 0

Row 3 0 0 1 0 0

Row 4 0 0 1 0 0

Column Data Ranges

Row 0 00H to 1FH

Row 1 20H to 3FH

Row 2 40H to 5FH

Row 3 60H to 7FH

Row 4 80H to 9FH

LOAD

Row Address Decode

Write Character/

Write 50 x 5

Read 10 x 25

Column Output

RAM

250 bits

Display Multiplexer

Adddress

Character

Adddress

Word

Control 4

Software

Clear

OPCODE

Decode

D7 D6 D5

OPCODE DATA

D4 D3 D2 D1 D0

Power Down

Brightness &

Lamp Test

Data Clock

Serial

Data

Oscillator

Counter Chain

& Timing Logic

Column Logic & Driver

10 2345 89

10 - 5 x 5 Characters

& Driver

Row Decoder 10

MUX CLK I/O

MUX Clock SEL

RESET

IDBD5069

Serial

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A
2008-07-22 8
The following explains how to format the serial data to be loaded 
into the display. The user supplies a string of bit mapped decoded 
characters . The contents of this string is shown in Figu re „Loading 
Serial Character Data a“ (page 8). Figure „Loading Serial Charac-
ter Data b“ (page 8) shows that each character consist of six 8 bit 
words. The first word encodes the display character location and 
the succeeding five bytes are row data. The row data represents 
the status (On, Off) of individual column LEDs. Figure „Loading 
Serial Character Data c“ (page 8) shows that each 8 bit word is 
formatted to include a three bit Operational Code (OPCODE) 
defined by bits D7–D5 and five bits (D4–D0) representing Column 
Data, Character Address, or Control Word Data. 
Figure „Loading Serial Character Data d“ (page 8) shows the 
sequence f or loading the b ytes of da ta. Bringing the LOAD line lo w 
enables the serial register to accept data. The shift action occurs 
on the low to high transition of the serial data clock (SDCLK). The 
least significant bit (D0) is loaded first. After eight clock pulses the 
LOAD line is brought high. With this transition the OPCODE is 
decoded. The decoded OPCODE directs D4–D0 to be latched in 
the Character Address register, stored in the RAM as Column 
data, or latched in the Control Word register. The control IC 
requires a minimum 600 ns delay between successive byte loads. 
As indicated in Figure „Loading  Serial Character  Data a“ (page 8), 
a total of 660 clock cycles (60-8 bit words) are required to load all 
ten characters into the display. 
The Character Address Register bits , D4–D0 (Table „Load Char ac-
ter Address“ (page 9)) and Row Address Register bits, D7–D5 
(Table „Load Column Data“ (page 9)) direct the Column Data bits, 
D4–D0 (Table „Load Column Data“  (page 9)) to specific RAM loca -
tion. Table „Characte r ’D’“ (page 8) shows the Ro w Address for the 
example character “D.” Column data is written and read asynchro-
nously from the 250 bit RAM. Once loaded the internal oscillator 
and character multiplexer reads the data from the RAM. These 
characters are row strobed with column data as shown in Figures 
„Row and Column Location“ (page 9) and „Row Strobing“ 
(page 10). The character strobe rate is determined by the internal 
or user supplied external MUX Clock and the IC’s ÷ 320 counter. 
Loading Serial Character Data
Character “D”
Op code 
D7 D6  D5 Column Data 
D4 D3 D2 D1 D0 
C0 C1 C2 C3 C4
Hex
Row 0 000  111101E
Row 1 001  1000131
Row 2 010  1000151
Row 3 011  1000171
Row 4 100  111109E
Character 0 Character 1 Character 2 Character 3 Character 4 Character 5 Character 6 Character 7 Character 8 Character 9
660 Clock Cycles, 132 μs
Example: Serial Clock = 5 MHz, Clock Period = 200 ns  
Time between  LOADS 
LOAD
Serial 
Clock
DATA
Clock
Period
t0
D0   D1   D2   D3   D4   D5   D6   D7  
11 Clock Cycles, 2.2  s
  Time
Between
Loads 
 
OPCODE
Character Address OPCODE
Column   Data
D0
C4  D1
C3   D2
C2 D3
C1   D4
C0  
Character 0
  Address  Row 0  Column
       Data
66 Clock Cycles,  13.2 μs  
Row 1  Column
       Data Row 2 Column
       Data Row 3 Column
       Data Row 4  Column
       Data
D0
 0   D1
 0   D2
 0   D3
 0   D4
 0   D5
 1   D6
 0   D7
 0   D5   D6   D7  
a.
b.
c.
d.
11 Clock Cycles, 2.2  s
600 ns(min.)
  Time
Between
Loads 
600 ns(min.)

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

2008-07-22 9

The user can activate four Control functions. These include: LED

Brightness Level, Lamp Test, IC Power Down, or Display Clear.

OPCODEs and five bit words are used to initiate these functions.

The OPCODEs and Control Words for the Character Address and

Loading Column Data are shown in Tables „Load Character

Address“ (page 9) and „Load Column Data“ (page 9).

The user can select seven specific LED brightness levels, Table

„Display Brightness“ (page 9). The se brightness le vels (in percent-

ages of full brightness of the display) include: 100% (F0 HEX), 53%

(F1HEX), 40% (F2HEX), 27% (F3HEX), 20% (F4HEX), 13% (F5HEX),

and 6.6% (F6HEX). The brightness levels are controlled by chang-

ing the duty factor of the row strobe pulse.

Row and Column Location

The SCD5510XA offers a unique Display Power Down feature

which reduces ICC to less than 50 µA. When FFHEX is loaded, as

shown in Table „Power Down“ (page 9), the display is set to 0%

brightness and the internal multiplex clo ck is stopped. When in the

Power Down mode data may still be written into the RAM. The dis-

pla y is reactivated b y loading a new Brightness Le vel Contro l Word

into the display.

The Lamp Test is enabled by loading F8 HEX, Table „Lamp Test“

(page 9), into the serial shift register. This Control Word sets all of

the LEDs to a 53% brightness level. Operation of the Lamp Test

has no affect on the RAM and is cleared by loading a Brightness

Control Word.

The Software Clear (C0HEX), given in Table „Software Clear“

(page 9), clears the Address Registe r and the RAM. The displa y is

blanked and the Character Address Register will be set to Charac-

ter 0. The internal counter and th e Control Word Register are u naf-

fected. The Software Clear will remain active until the next data

input cycle is initiated.

Load Character Address

Op code

D7 D6 D5 Character Address

D4 D3 D2 D1 D0 Hex Operation

Load

101 10 0 0 0 B0 Character 0

101 10 0 0 1 B1 Character 1

101 10 0 1 0 B2 Character 2

101 10 0 1 1 B3 Character 3

101 10 1 0 0 B4 Character 4

101 10 1 0 1 B5 Character 5

101 10 1 1 0 B6 Character 6

101 10 1 1 1 B7 Character 7

101 11 0 0 0 B8 Character 8

101 11 0 0 1 B9 Character 9

Load Column Data

Op code

D7 D6 D5 Column Data

D4 D3 D2 D1 D0 Operation Load

000 C0 C1 C2 C3 C4 Row 0

001 C0 C1 C2 C3 C4 Row 1

010 C0 C1 C2 C3 C4 Row 2

011 C0 C1 C2 C3 C4 Row 3

100 C0 C1 C2 C3 C4 Row 4

IDXX5187

Row 0

Row 1

Row 2

Row 3

Row 4 01234

Previously "on" LED

On LED

Off LED

Columns

Display Brightness

Op code

D7 D6 D5 Control Word

D4 D3 D2 D1 D0 Hex Operation

Level

111 10 0 0 0 F0 100%

111 10 0 0 1 F1 53%

111 10 0 1 0 F2 40%

111 10 0 1 1 F3 27%

111 10 1 0 0 F4 20%

111 10 1 0 1 F5 13%

111 10 1 1 0 F6 6.6%

Power Down

Op code

D7 D6 D5 Control Word

D4 D3 D2 D1 D0 Hex Operation

Level

111 11 1 1 1 FF 0%

brightness

Lamp Test

Op code

D7 D6 D5 Control Word

D4 D3 D2 D1 D0 Hex Operation

Level

111 10 BB B Lamp Test

(OFF)

111 11 0 0 1 F8 Lamp Test

(OFF)

Software Clear

Op code

D7 D6 D5 Control Word

D4 D3 D2 D1 D0 Hex Operation

Level

110 00 0 0 0 C0 CLEAR

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

2008-07-22 10

Row Strobing

Multiplexer and Display Driver

The ten characters are row multiplexed with RAM resident column

data. The strobe rate is established by the internal or external

MUX Clock rate. The MUX Clock frequency is divided by a 320

counter chain. This results in a typical strobe rate of 750 Hz. By

pulling the Clock SEL line low, the display ca n be operated from an

external MUX Clock. The external clock is attached to the CLK I/O

connection (pin 15). The maxim um external MUX Clock frequency

should be limited to 1.0 MHz.

An asynchronous hardware Reset (pin 13) is also provided. Bring-

ing this pin low will clear the Character Address Register, Control

W ord Register , RAM, and blanks the displa y. This action lea ves the

display set at Char acter Address 0, and the Brightness Lev el set at

100%.

Electrical & Mechanical Considerations

Interconnect Considerations

Optimum product performance can be had when the following

electrical and mechanical recommendations are adopted. The

SCD5510XA’s IC is constructed in a high speed CMOS process,

consequently high speed noise on the SERIAL DATA, SERIAL

DATA CLOCK, LOAD and RESET lines may cause incorrect data

to be written into the serial shift register. Adhere to transmission

line termination procedures when using fast line drivers and long

cables (>10 cm).

Good digital grounds (pins 14, 28) and power supply decoupling

(pins 6, 9, 20, 23) will insure that ICC (<400 mA peak) switching

currents do not generate localized ground bounce. Therefore it is

recommended that each display package use a 0.1 µF and 20 µF

capacitor between VCC and ground.

When the internal MUX Clock is being used connect the CLKSEL

pin to VCC. In those applications where RESET will not be con-

nected to the system’s reset control, it is recommended that this

pin be connected to the center node of a series 0.1 µF and 100 kΩ

RC network. Thus upon initial power up the RESET will be held

low for 10 ms allowing adequate time for the system power supply

to stabilize.

The SCD5510XA allows up to 1.7 W of power dissipation at 70 °

and 1.29 W power dissipation at a maximum operating tempera-

ture of 85°C . Approximately 60% of this power is dissipated by the

IC to the PC board via the VCC connection (pin s 6, 9, 20 , 23). Op ti-

mum thermal reliability is obtained by connecting all of the VCC

pins to a com mon pad locat ed on both si des of the PC b oard. This

techniqu e o ffers a low thermal resis tan ce for IC to system am bi-

ent.

ESD Protection

The input protect ion structure of th e SC D55 10 0A/ 1A/2 A/3 A/ 4A

provides significant protection against ESD damage. It is capable

of withstanding discharges greater than 2.0 kV. Take all the stan-

dard precautions, normal for CMOS components. These include

properly grounding personnel, tools, tables, and transport carriers

that come in contact with unshielded parts. If these conditions are

not, or cannot be met, keep the leads of the device shorted

together or the parts in anti-static packaging .

Soldering Considerations

The SCD55100A/1A/2A/3A/4A can be hand soldered with SN63

solder using a grounded iron set to 260°C.

Wave soldering is also possible following these conditions: Pre-

heat that does not e xceed 93°C on the solder side of the PC board

or a package surface temperature of 85°C. Water soluble organic

acid flux (except carboxylic acid) or rosin-based RMA flux without

alcohol can be used.

Wa ve temperature of 245°C ± 5°C with a dwell between 1.5 sec. to

3.0 sec. Exposure to the wave shou ld no t exceed temperatures

above 260°C for five s econ ds a t 1. 59 mm (0.063") below the seat-

ing plane. The p ackages should no t be imm er sed in th e wa ve.

Post Solder Cleaning Procedures

The least offensive cleaning solution is hot D.I. water (60 °C) for

less than 15 minutes . Addition of mild saponifiers is acceptab le. Do

not use commercial dishwasher detergents.

For faster cleaning, solvents may be used. Exercise care in choos-

ing solvents as some may chemically attack the nylon package.

Maxim um e x posure should not exceed two min utes at elevated tem -

peratur e s. Accept able so lvent s are TF (t richlo rot rifluo ret ha ne ) , TA,

111 Trichloroethane, and unheated acetone.(1)

Note:

1) Acceptable commercial solvents are: Basic TF, Arklone, P.

Genesolv,

D. Genesolv DA, Blaco-Tron TF and Blaco-Tron TA.

Unacceptable solvents contain alcohol, methanol, methylene

chloride, ethanol, TP35, TCM, TMC, TMS+, TE, or TES. Since

many commercial mixtures exist, contact a solvent vendor for

chemical composition information. Some major solvent manufac-

turers are: Allied Chemical Cor poration, Specialty Chemical Divi-

sion, Morristown, NJ; Baron-Blakeslee, Chicago, IL; Dow

Chemical, Midland, MI; E.I. DuPont de Nemours & Co., Wi lming-

ton, DE.

IDXX5188

Row 0

Row 1

Row 2

Row 3

Row 4 01234

Columns

Load Row 0

Load

Row 4

Columns

10 2 3

Row 3

Row 1

Row 0

Row 2

Load Row 1

Columns

Row 4 1

0 2 43

Load Row 2

Row 2

Row 1

Row 3

Row 0

Row 4 0Columns

213

Load Row 3

Row 0

Row 3

Row 1

Row 2

Row 4

Columns

012 43

Row 2

Row 1

Row 3

Row 0

Load Row 4Row

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

2008-07-22 11

For further information refer to Appnotes 18 and 19 at www.osram-os.com

An alternative to soldering and cleaning the display modules is to use sockets. Naturally, 28 pin DIP sockets 7.62 mm (0.300") wide with

2.54 mm (0.100") ce nters wo rk well f or single displays . Multiple display assemblies are best h andled b y longer SIP so ck et s or DIP sockets

when available for uniform package alignment. Socket manufacturers are Aries Electronics, Inc., Frenchtown, NJ; Garry Manufacturing,

New Brunswick, NJ; Robinson-Nugent, New Albany, IN; and Samtec Electronic Hardward, New Albany, IN.

For further information refer to Appnote 22 at www.osram-os.com

Optical Considerations

The 3.683 mm (0.145") high cha racte r of the SCD 5 51 0XA gives reada bil it y up t o ei gh t feet. Proper filt e r se le cti on en ha nces rea da b ili ty

over this distance.

Using filters emphasizes the contrast ratio between a lit LED and the character background. This will increase the discrimination of differ-

ent characters. The only limitation is cost. Tak e int o con sideration the ambient lighting environment for the best cost/benefit ratio f or filters.

Incandescent (with almost no green) or fluorescent (with almost no red) lights do not have the flat spectral response of sunlight. Plastic

band-pass filters are an inexpensive and effective way to strengthen contrast ratios. The SCD5510A/2A are red/high efficiency red dis-

plays and should be matched with long wavelength pass filter in the 570 nm to 590 nm range. The SCD55103A/4A should be matched

with a yello w-g reen band-pass f ilter that pea ks at 565 nm . For displays of m ultiple colo rs , neutr al den sity g re y filters offer the best compro-

mise.

SCD Interface with Siemens/Intel 8031 Microprocessor

(using serial port in mode 0)

IDCD5221

XTAL2 RxD

18 10

19 XTAL1

RST

9 17

P3.7 13

P3.3

P3.4 14

8031

TxD 11

CLK LOAD

DATA

40 SCD

Master

2691314

28 27 23 20 19 16 15 15

DATA

LOAD

CLK

6 9 13 14

Slave

SCD

28 23 20 19 16

TAN

0.01 µF

22 µF

2008-07-22 12

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

Additional contrast enhancement is gained by shading the displays. Plastic band-pass filters with built-in louvers offer the next step up in

contrast impro vemen t. Plastic filters can be improv ed further with anti-reflectiv e coatings to reduce glare. The trade-off is fuzzy char acters.

Mounting the filters close to the display reduces this effect. Take care not to overheat the plastic filter by allowing for proper air flow.

Optimal filter enhancements are gained by using circular polarized, anti-reflective, band-pass filters. The circular polarizing further

enhances contrast by reducing the light that travels through the filter and reflects back off the display to less than 1%.

Several filter manufacturers supply quality filter materials. Some of them are: Panelgraphic Corporation, W. Caldwell, NJ; SGL Homalite,

Wilmington, DE; 3M Company, Visual Products Division, St. Paul, MN; Polaroid Corporation, Polarizer Division, Cambridge, MA; Marks

Polarized Corporation, Deer Park, NY, Hoya Optics, Inc., Fremont, CA.

One last note on mounting filters: recessing displays and bezel assemblies is an inexpensive way to provide a shading effect in o verhead

lighting situations. Several Bezel manufacturers are: R.M.F. Products, Batavia, IL; Nobex Components, Griffith Plastic Corp., Burlingame,

CA; Photo Chemical Products of California, Santa Monica, CA; I.E.E.–Atlas, Van Nuys, CA.

Microprocessor Interface

The microprocessor interface is through the serial port, SPI port or one out of eight data bits on the eight bit parallel port and also control

lines SDCLK and LOAD.

Power Up Sequence

Upon power up display will come on at random. Thus the display should be reset at power-up. The reset will set the Address Register to

Digit 0, User RAM is set to 0 (displa y blank) the Control W ord is set to 0 (100% brightness with Lamp Test off) and the internal counters are

reset.

SCD5510XA Interface with Siemens/Intel 8031 Microprocessor

P0.0

P3.6

P3.1

P3.0

P1.0

RST

8031

XTAL1

XTAL2

Slave

LOAD

CLK

1 2

28 DATA

Master

1369 14

SCD

20 16

CLK

SD LOAD

2728 DATA

14139

SCD

19 15

22 µF

TAN

0.01 µF

IDCD5222

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

2008-07-22 13

SCD5510XA Interfac e with Motorola 68HC05C4 Microprocessor

(using SPI port)

Cascading Multiple Displays

Multiple displays can be cascaded using the CLKSEL and CLK I/O pins as shown below. The display designated as the Master Clock

source should have its CLKSEL pin tied high and the slaves should have their CLKSEL pins tied low. All CLK I/O pins should be tied

together. One display CLK I/O can drive 15 slave CLK I/Os. Use RST to synchronize all display counters.

Cascading Multiple Displays

IDCD5223

MOSI

SCLK

PA1

PA0

PA2

RST

68HC05C4

OSC2

OSC1

CLK LOAD

126 139

DATA

SCD

Master

28 27 23 1920

TAN

22 µF

SCD

Slave

CLK

1LOAD

DATA

91314

2015 28 27 23 19 16 15

0.01 µF

IDCD5030

RST CLK SEL

Intelligent Display

DATA SDCLK LOAD

14 more displays

in between

DATA

SDCLK

Decoder

Address Address Decode 1-14

RST

CLK I/O

Intelligent Display

DATA

RST

SDCLK

CLK I/O

LOAD

CLK SEL

Chip

LD CE

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

2008-07-22 14

Loading Data Into the Display

Use following procedure to load data into the display:

1. Power up the display.

2. Bring RST low (600 ns duration minimum) to clear the Multi-

plex Counter, Address Register, Control Word Register,

User Ram and Data Register. The display will be blank. Dis-

play brightness is set to 100%.

3. If a different brightness is desired, load the proper brightness

opcode into the Control Word Register.

4. Load the Digit Address into the display.

5. Load display row and column data for the selected digit.

6. Repeat steps 4 and 5 for all digits.

Data Contents for the Word “Displays”

Step D7 D6 D5 D4 D3 D2 D1 D0 Function

B (optional) 11 0

11 1

0000 0

10BB B

CLEAR

BRIGHT NESS SELECT

10 1

000

00 1

01 0

01 1

10 0

10000

11110

10001

11110

DIGIT D0 SELECT

ROW 0 D0 (D)

ROW 1 D0 (D)

ROW 2 D0 (D)

ROW 3 D0 (D)

ROW 4 D0 (D)

101

000

001

010

011

100

10001

01110

00100

01110

DIGIT D1 SELECT

ROW 0 D1 (I)

ROW 1 D1 (I)

ROW 2 D1 (I)

ROW 3 D1 (I)

ROW 4 D1 (I)

101

000

001

010

011

100

10010

01111

10000

01110

00001

11110

DIGIT D2 SELECT

ROW 0 D2 (S)

ROW 1 D2 (S)

ROW 2 D2 (S)

ROW 3 D2 (S)

ROW 4 D2 (S)

101

000

001

010

011

100

10011

11110

10001

11110

10000

DIGIT D3 SELECT

ROW 0 D3 (P)

ROW 1 D3 (P)

ROW 2 D3 (P)

ROW 3 D3 (P)

ROW 4 D3 (P)

101

000

001

010

011

100

10100

10000

11111

DIGIT D4 SELECT

ROW 0 D4 (L)

ROW 1 D4 (L)

ROW 2 D4 (L)

ROW 3 D4 (L)

ROW 4 D4 (L)

101

000

001

010

011

100

10101

00100

01010

11111

10001

DIGIT D5 SELECT

ROW 0 D5 (A)

ROW 1 D5 (A)

ROW 2 D5 (A)

ROW 3 D5 (A)

ROW 4 D5 (A)

101

000

001

010

011

100

10110

10001

01010

00100

DIGIT D6 SELECT

ROW 0 D6 (Y)

ROW 1 D6 (Y)

ROW 2 D6 (Y)

ROW 3 D6 (Y)

ROW 4 D6 (Y)

101

000

001

010

011

100

10111

01111

10000

01110

00001

11110

DIGIT D7 SELECT

ROW 0 D7 (S)

ROW 1 D7 (S)

ROW 2 D7 (S)

ROW 3 D7 (S)

ROW 4 D7 (S)

Note:

If the display is already reset at Power Up, there is no need for Softwa re Clear.

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

2008-07-22 15

User Definable Character Set Examples*

Upper and Lower Case Alphabets

Numerals and Punctuation

*CAUTION: No more than 128 LEDs “on” at one time at 100% brightness.

IDCS5089

HEX

CODE CODE

HEX CODE

HEX

04 1E

1E 30

IDCS5090

HEX

CODE CODE

HEX CODE

HEX

0E 04

1E 30

2008-07-22 16

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

User Definable Character Set Examples* (continued)

Scientific Notations, etc.

Foreign Characters

*CAUTION: No more than 128 LEDs “on” at one time at 100% brightness.

IDCS5091

HEX

CODE CODE

HEX CODE

HEX

06 04

1F 32

IDCS5092

HEX

CODE CODE

HEX CODE

HEX

1F 1F

04 3F

SCD55100A, SCD55101A, SCD55102A, SCD55103A, SCD55104A

2008-07-22 17

Published by

OSRAM Opto Semiconductors GmbH

Wernerwerkstrasse 2, D-93049 Regensburg

www.osram-os.com

Attention please!

The information describes the type of component and shall not be considered as assured characteristics.

Terms of delivery and rights to change design reserved. Due to technical requirements components may contain

dangerous substances. For information on the types in question please contact our Sales Organization.

If printed or downloaded, please find the lates t ve rsion in the Internet.

Packing

Please use the recycling operators known to you. We can also help you – get in touch with your nearest sales office.

By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing

material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs

incurred.

Components used in life-support devices or systems must be expressly authorized for such purpose! Critical

components1) may only be used in life-support devices or systems2) with the express written approval of OSRAM OS.

1) A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the

failure of that life-support device or system, or to affect its safety or the effectiveness of that device or system.

2) Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain

human life. If they fail, it is reasonable to assume that the health and the life of the user may be endangered.

Revision History: 2008-07-22

Previous Version: 2006-02-20

Page Subjects (major changes since last revision) Date of change

all Lead free device 2006-01-23

6Pin assignment corrected 2008-07-22