Freescale Semiconductor User's Guide Document Number: KT34845UG Rev. 1.0, 6/2009 KIT34845EPEVME Evaluation Board Figure 1. 33845 Evaluation Board (EVB) Table of Contents 1 Kit Contents / Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 Important Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 EVB Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 Required Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 EVB Setup Configuration Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6 Using Demo Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 7 LED Load Board Configuration (6 Channels x 10 LEDs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 8 Performance of the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 9 EVB Schematic (1) - MC34845 Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 10 EVB Schematic (2) - MC34845 Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 11 EVB Schematic (3) - MC34845 MCU Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 12 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 13 EVB Board BOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 14 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 15 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 (c) Freescale Semiconductor, Inc., 2009. All rights reserved. Kit Contents / Packing List 1 Kit Contents / Packing List * * * EVB - KIT34845EPEVME Cable for LED board connection CD KIT34845EPEVME Evaluation Board, Rev. 1.0 2 Freescale Semiconductor Important Notice 2 Important Notice Freescale provides the enclosed product(s) under the following conditions: This evaluation kit is intended for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY. It is provided as a sample IC pre-soldered to a printed circuit board to make it easier to access inputs, outputs, and supply terminals. This EVB may be used with any development system or other source of I/O signals by simply connecting it to the host MCU or computer board via off-the-shelf cables. This EVB is not a Reference Design and is not intended to represent a final design recommendation for any particular application. Final device in an application will be heavily dependent on proper printed circuit board layout and heat sinking design as well as attention to supply filtering, transient suppression, and I/O signal quality. The goods provided may not be complete in terms of required design, marketing, and or manufacturing related protective considerations, including product safety measures typically found in the end product incorporating the goods. Due to the open construction of the product, it is the user's responsibility to take any and all appropriate precautions with regard to electrostatic discharge. In order to minimize risks associated with the customers applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. For any safety concerns, contact Freescale sales and technical support services. Should this evaluation kit not meet the specifications indicated in the kit, it may be returned within 30 days from the date of delivery and will be replaced by a new kit. Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typical", must be validated for each customer application by customer's technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale was negligent regarding the design or manufacture of the part.FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc. 2008 KIT34845EPEVME Evaluation Board, Rev. 1.0 Freescale Semiconductor 3 EVB Introduction 3 EVB Introduction This EVB shows the functionality of MC34845 set up under specific operation parameters. MC34845 which is a high efficiency, LED driver for use in backlighting LCD displays from 10" to 17"+ can operate in this demo board from a supply of 5V, the device is capable of driving up to 96 LEDs in 6 parallel strings. The current through these 6 channels is matched to within 2%. For evaluation purposes this Demo Board includes a simple MCU that allows control of the light dimming of the LEDs as well as the PWM frequency from 200Hz to 26.5kHz. 3.1 EVB Operation Parameters * * * * * * * 3.2 EVB Features * * * * * * * * 3.3 MCU that allows dimming control at different duty cycles and PWM frequency (200Hz to 26.5kHz) Four Layer Board Low Noise Design Top Layer Placement Connector for the 6 LED channels Terminal Blocks for Input and output Voltage Jumper signal configurations and resistors array for signal adjusting Test points measurements MC34845 Features * * * * * * * * * * 3.4 Input Voltage (Vin) = 9V +/- 10% Expected Output Voltage (Vout) = around 30V LED Load = 10 LEDs x 6 Channels Duty Cycle = All range (minimum pulse of 400ns) Peak Current on all channels = all range up to 20mA OVP = 35V (For 10Leds) Boost Frequency = 600KHz Input voltage of 5V to 21V Output Voltage up to 60V, with auto Vout selection 2.0A integrated boost Up to 30mA LED current per channel 90% efficiency (DC:DC) 6-channel current mirror with 2% current matching Input PWM frequency programmable from DC to 100 KHz Hardware programmable OVP LED failure detection and OTP/OCP/UVLO lockout 24-Ld 4x4x0.65mm QFN Pb-Free packaging MCU (MC9S08SH8) Features For this EVB it is important to highlight the following MCU features: KIT34845EPEVME Evaluation Board, Rev. 1.0 4 Freescale Semiconductor EVB Introduction * * * On Chip memory - 8K FLASH read/program/erase over full operating voltage and temperature. Internal Clock Source (ICS) -- Internal clock source module containing a frequency-lockedloop (FLL) controlled by internal or external reference; precision trimming of internal reference allows 0.2% resolution and 2% deviation over temperature and voltage Real-time counter - 8-bit modulus counter with binary or decimal based prescaler; External clock source for precise time base, time-of-day calendar or task scheduling functions; Free running on-chip low power oscillator (1 kHz) for cyclic wake-up without external components, runs in all MCU modes For more information about this MCU please refer to : http://www.freescale.com/files/microcontrollers/doc/data_sheet/MC9S08SH8.pdf KIT34845EPEVME Evaluation Board, Rev. 1.0 Freescale Semiconductor 5 Required Equipment 4 4.1 Required Equipment Hardware Requirements * * * Power Supply (up to 30V @ 3A) LED Board 12 Wires cable for LED board connection KIT34845EPEVME Evaluation Board, Rev. 1.0 6 Freescale Semiconductor EVB Setup Configuration Diagram 5 EVB Setup Configuration Diagram External power supply V+ & GND connector 6 LED Channels plus V+ & GND Figure 1. EVB Setup Configuration Diagram KIT34845EPEVME Evaluation Board, Rev. 1.0 Freescale Semiconductor 7 Using Demo Board 6 Using Demo Board 6.1 Demo Board Jumper Connections JUMPER CONNECTION FUNCTION DESCRIPTION Fail pin to +5V This jumper connects the FAIL pin to +5V thru a pull-ip resistor. OVP - HW Controlled This jumper connects the OVP pin to a resistor divider which sets the OVP value respect to the internal threshold of 6.9V. This resistor divider is connected from Vout to GND. Please refer to Schematic to set the correct resistance value based on your needs. J6 WAKE to GND This jumper connects the WAKE pin to GND. J8 WAKE operation This jumpers connects WAKE and PWM together, thus enabling the low power consumption (shutdown) mode without the need of using an extra logic signal for enable. J9(1-2) PWM pin to VDC1 Sets PWM pin to HIGH level, i.e. 100% duty cycle, J9(2-3) PWM pin to GND Sets PWM pin to LOW level, i.e. 0% duty cycle. J10(1-2) Chip enable Enables the IC as it takes EN to HIGH. J10(2-3) Chip disable DIsables the IC as it takes EN to GND. Connection used when operating in WAKE operation. J13 LDO enable Powers up the +5V LDO regulator for the MCU and fail circuits. J14 MCU PWM signal Connects the the PWM signal generated by the MCU to the PWM pin of the IC. J15 FAIL pin LED Connect LED for Fail condition indicator. When a fault situation is detected such as an LED channel open or boost over-current this pin goes into high impedance, making the LED to light up. (LED ON = Fail Condition, LED OFF = OK) J2 J3(2-3) Note: Jumpers J9 & J14 should not be connected at the same time. 6.2 Demo Board Operation 6.2.1 Stand Alone Mode, i.e. On-board PWM Dimming Apply an external power supply to J1. When the LED D3 is turned on, it is possible to increase (SW1) or decrease (SW2) the duty cycle of the PWM dimming signal generated by the MCU. When pressing both switches at the same time and the LED D3 is turned off, it is possible to increase (SW1) up to 26.5KHz or decrease (SW2) down to 200Hz the frequency of the PWM dimming signal generated by the MCU. 6.2.2 External Control Mode Remove jumpers at J9 and J14. Apply an external power supply to J1. Thru a function generator apply a 0V to 5V square wave signal to the test point TP11. With this external signal, it is possible to evaluate the PWM dimming performance of the MC34845 by varying both the frequency and duty cycle. KIT34845EPEVME Evaluation Board, Rev. 1.0 8 Freescale Semiconductor LED Load Board Configuration (6 Channels x 10 LEDs) 7 LED Load Board Configuration (6 Channels x 10 LEDs) JUMPERS CONNECTED Figure 2. LED Load Board Jumper Function: * * * Top horizontal jumpers: Channel strings enabled. This LED board has all channels populated but for the KIT34845EPEVME it is only necessary to enable from I0 to I5. Bottom horizontal jumpers : Short circuits each of the current driver channels to the voltage of the boost. Vertical jumpers: Enable/Disable 1,2,3,4 or 6 LEDs per string. Placing a jumper in the first vertical header at the bottom will enable only 10 LEDs per string. KIT34845EPEVME Evaluation Board, Rev. 1.0 Freescale Semiconductor 9 Performance of the System 8 8.1 Performance of the System Network Compensation Since this Boost converter is current controlled, a Type II compensation is needed. For this type of compensation it is recommended to push out the Right Half Plane Zero to higher frequencies where it will not significantly affect the overall loop. 2 V OUT x ( 1 - D ) f RHPZ = --------------------------------------I OUT x 2 x L The crossover frequency must be set much lower than the location of the Right Half Plane Zero. f RHPZ f CROSS = ------------5 Since the MC34845 has a fixed slope compensation, RCOMP should be fixed for all configurations, i.e. RCOMP = 8.2k. As a result, CCOMP1 and CCOMP2 should be calculated as follows: 2 C COMP1 = ----------------------------------------------------2 x f CROSS x R COMP GM C COMP2 = --------------------2 x f SW The recommended values of these capacitors for an acceptable performance of the system in different operating conditions are CCOMP1 = C7 = 2.2nF and CCOMP2 = C8 = 56pF. In order to improve the transient response of the boost a resistor divider, R2 and R10, has been implemented from the PWM pin to ground with a connection to the compensation network. This configuration injects a 1V signal to the COMP pin and the equivalent Thevenin resistance of the divider is close to RCOMP, i.e. R2 = 10k and R10 = 39k. If a faster transient response is needed, a higher voltage (e.g. 1.3V) should be injected to the COMP pin; so the resistor divider should be modified accordingly but keeping the equivalent Thevenin resistance of the divider close to RCOMP. KIT34845EPEVME Evaluation Board, Rev. 1.0 10 Freescale Semiconductor EVB Schematic (1) - MC34845 Section 9 EVB Schematic (1) - MC34845 Section Figure 3. EVB Schematic (1) KIT34845EPEVME Evaluation Board, Rev. 1.0 Freescale Semiconductor 11 EVB Schematic (2) - MC34845 Section 10 EVB Schematic (2) - MC34845 Section Figure 4. EVB Schematic (2) KIT34845EPEVME Evaluation Board, Rev. 1.0 12 Freescale Semiconductor EVB Schematic (3) - MC34845 MCU Section 11 EVB Schematic (3) - MC34845 MCU Section Figure 5. EVB Schematic (3) KIT34845EPEVME Evaluation Board, Rev. 1.0 Freescale Semiconductor 13 Board Layout 12 Board Layout 12.1 Assembly Layer Top Figure 6. Assembly Layer Top KIT34845EPEVME Evaluation Board, Rev. 1.0 14 Freescale Semiconductor Board Layout 12.2 Silk Screen Top Figure 7. Silk Screen Top KIT34845EPEVME Evaluation Board, Rev. 1.0 Freescale Semiconductor 15 Board Layout 12.3 Top Layer Routing Figure 8. Top Layer Routing KIT34845EPEVME Evaluation Board, Rev. 1.0 16 Freescale Semiconductor Board Layout 12.4 Bottom Layer - GND Plane and Routing Figure 9. Bottom Layer - GND Plane KIT34845EPEVME Evaluation Board, Rev. 1.0 Freescale Semiconductor 17 Board Layout 12.5 Silk Screen Bottom - (Mirrored) Figure 10. Silk Screen Bottom KIT34845EPEVME Evaluation Board, Rev. 1.0 18 Freescale Semiconductor Board Layout 12.6 Fabrication Drawing Figure 11. Fabrication Drawing KIT34845EPEVME Evaluation Board, Rev. 1.0 Freescale Semiconductor 19 EVB Board BOM 13 EVB Board BOM Schematic Designator Device Type Description Manufacturer PN Freescale Components U1 MC34845EP qfn24 IC DRV 6 Channel LED 600kHz 5-21V QFN 24 MC34845EP U2 MC9S08SH8MSC qfn48 IC MCU 8BIT 48MHZ 8KB FLASH 2.7-5.5V QFN8 MC9S08SH8MSC Capacitors & Resistors C1 0.1UF CC0603 CAP CER 0.1UF 50V 10% X7R 0603 GRM188R71H104KA93D C2 10UF CC1210 CAP CER 10UF 35V +80%/-20% Y5V 1210 GMK325F106ZH C3 1uF CC1210 CAP CER 1UF 100V 10% X7R 1210 HMK325B7105KN-T C4 1uF CC1210 CAP CER 1UF 100V 10% X7R 1210 HMK325B7105KN-T C5 1uF CC1210 CAP CER 1UF 100V 10% X7R 1210 HMK325B7105KN-T C6 2.2uF CC0603_OV CAP CER 2.2UF 16V 10% X5R 0603 GRM188R61C225KE15D C7 2200PF CC0603 CAP CER 2200PF 50V 10% X7R 0603 C0603C222K5RACTU C8 56.0PF CC0603 CAP CER 56.0PF 50V 5% C0G 0603 GRM1885C1H560JA01D C9 2.2uF CC0603_OV CAP CER 2.2UF 16V 10% X5R 0603 GRM188R61C225KE15D C10 100PF CC0603 CAP CER 100PF 50V 10% X7R 0603 C0603X7R500-101KNP C11 10PF CC0603_OV CAP CER 10PF 50V 1% C0G 0603 C0603C100F5GAC C12 100PF CC0603 CAP CER 100PF 50V 10% X7R 0603 C0603X7R500-101KNP C13 100PF CC0603 CAP CER 100PF 50V 10% X7R 0603 C0603X7R500-101KNP C14 10PF CC0603_OV CAP CER 10PF 50V 1% C0G 0603 C0603C100F5GAC C15 10PF CC0603_OV CAP CER 10PF 50V 1% C0G 0603 C0603C100F5GAC C16 10PF CC0603_OV CAP CER 10PF 50V 1% C0G 0603 C0603C100F5GAC C17 10PF CC0603_OV CAP CER 10PF 50V 1% C0G 0603 C0603C100F5GAC C18 10PF CC0603_OV CAP CER 10PF 50V 1% C0G 0603 C0603C100F5GAC C19 10PF CC0603_OV CAP CER 10PF 50V 1% C0G 0603 C0603C100F5GAC C20 0.1UF CC0603_OV CAP CER 0.10UF 25V 10% X7R 0603 C0603C104K3RAC C21 0.1UF CC0603_OV CAP CER 0.10UF 25V 10% X7R 0603 C0603C104K3RAC C22 0.1UF CC0603_OV CAP CER 0.10UF 25V 10% X7R 0603 C0603C104K3RAC C23 0.1UF CC0603 CAP CER 0.1UF 50V 10% X7R 0603 GRM188R71H104KA93D C24 10UF CC0805_OV CAP CER 10UF 16V 10% X5R 0805 0805YD106KAT2A R1 1.2K RC0603_OV RES MF 1.2K 1/10W 1% 0603 RK73H1JTTD1201F R2 10.0K RC0603 RES MF 10.0K 1/10W 1% 0603 RK73H1JTTD1002F RK73H1JTTD7681F R3 7.68K RC0603_OV RES MF 7.68K 1/10W 1% 0603 R4 1.2K RC0603_OV RES MF 1.2K 1/10W 1% 0603 RK73H1JTTD1201F R5 115.0K RC0603_OV RES MF 115.0K 1/10W 1% 0603 RK73H1JTTD1153F R6 3.3K RC0603 RES MF 3.30K 1/10W 1% 0603 RK73H1JTTD3301F R7 16.0K RC0603_OV RES MF 16.0K 1/10W 1% 0603 RK73H1JTTD1602F R8 470 RC0603_OV RES MF 470 OHM 1/10W 5% 0603 CR0603-10W-471JT R9 4.70K RC0603_OV RES MF 4.70K 1/10W 1% 0603 RK73H1JTTD4701F R10 39K RC0603_OV RES MF 39.0K 1/10W 1% 0603 RK73H1JTTD3902F R11 4.70K RC0603_OV RES MF 4.70K 1/10W 1% 0603 RK73H1JTTD4701F Freescale does not assume liability, endorse, or warrant components from external manufacturers that are referenced in circuit drawings or tables. While Freescale offers component recommendations in this configuration, it is the customer's responsibility to validate their application KIT34845EPEVME Evaluation Board, Rev. 1.0 20 Freescale Semiconductor EVB Board BOM Schematic Designator Device Type Description Manufacturer PN Diodes D1 MBRA160T3G case403d_02 DIODE SCH PWR RECT 1A 60V CASE 403D MBRA160T3G D2 LED ORANGE 0603led LED OR SGL 20MA 0603 LO L29K-J2L1-24-Z D3 LED GREEN led_0603_c1 LED GRN SGL 20MA SMT HSMG-C190 1885180000 Headers and Connectors J1 CON_2_TB con2x2_tb_3p5_th CON 1X2 TB TH 3.5MM SP 508H SN J2 HDR_1X2 HDR102 HDR 1X2 TH 100MIL SP 375H AU 826629-2 J3 HDR_1X3 HDR103 HDR 1X3 TH 100MIL SP 330H AU TSW-103-07-G-S J6 HDR_1X2 HDR102 HDR 1X2 TH 100MIL SP 375H AU 826629-2 J7 CON_2_TB con2x2_tb_3p5_th CON 1X2 TB TH 3.5MM SP 508H SN 1885180000 J8 HDR_1X2 HDR102 HDR 1X2 TH 100MIL SP 375H AU 826629-2 J9 HDR_1X3 HDR103 HDR 1X3 TH 100MIL SP 330H AU TSW-103-07-G-S J10 HDR_1X3 HDR103 HDR 1X3 TH 100MIL SP 330H AU TSW-103-07-G-S J12 HDR 2X3 hdr203_m20 HDR 2X3 TH 2.54MM CTR 340H AU M20-9980345 J13 HDR_1X2 HDR102 HDR 1X2 TH 100MIL SP 375H AU 826629-2 J14 HDR_1X2 HDR102 HDR 1X2 TH 100MIL SP 375H AU 826629-2 J15 HDR_1X2 HDR102 HDR 1X2 TH 100MIL SP 375H AU 826629-2 J16 CON PLUG 12 hdr_12_xask CON 1X12 PLUG SHRD TH 2.5MM SP 346H SN 110L B12B-XASK-1(LF)(SN) L1 10UH ind_ihlp_2020 IND PWR 10UH@100KHZ 2.3A 20% SMT IHLP2020BZER100M01 L1 (MC34845A) 4.7UH ind_ihlp_2020 IND PWR 4.7UH@100KHZ 2.8A 20% SMT IHLP2020BZER4R7M01 LM2937-5.0 sot223 IC VREG LDO 5V 500MA 26V SOT-223 LM2937IMP-5.0/NOPB TP1 TEST POINT testpoint_138_059 TEST POINT PIN .138X.059 SMT C12000B TP2 TEST POINT testpoint_138_059 TEST POINT PIN .138X.059 SMT C12000B TP3 TEST POINT testpoint_138_059 TEST POINT PIN .138X.059 SMT C12000B TP4 TEST POINT testpoint_138_059 TEST POINT PIN .138X.059 SMT C12000B TP5 TEST POINT testpoint_138_059 TEST POINT PIN .138X.059 SMT C12000B TP6 TEST POINT testpoint_138_059 TEST POINT PIN .138X.059 SMT C12000B TP7 TEST POINT testpoint_138_059 TEST POINT PIN .138X.059 SMT C12000B TP8 TEST POINT testpoint_138_059 TEST POINT PIN .138X.059 SMT C12000B TP9 TEST POINT testpoint_138_059 TEST POINT PIN .138X.059 SMT C12000B TP10 TEST POINT testpoint_138_059 TEST POINT PIN .138X.059 SMT C12000B TP11 TEST POINT testpoint_138_059 TEST POINT PIN .138X.059 SMT C12000B TP12 TEST POINT testpoint_138_059 TEST POINT PIN .138X.059 SMT C12000B SW1 SW SPST NO sw4_spst_sq6p SW SPST MOM NO PB SMT 32V 50MA SM KSC321GLFS SW2 SW SPST NO sw4_spst_sq6p SW SPST MOM NO PB SMT 32V 50MA SM KSC321GLFS Inductors IC U3 Test Points Push buttons Freescale does not assume liability, endorse, or warrant components from external manufacturers that are referenced in circuit drawings or tables. While Freescale offers component recommendations in this configuration, it is the customer's responsibility to validate their application KIT34845EPEVME Evaluation Board, Rev. 1.0 Freescale Semiconductor 21 EVB Board BOM In some PWM dimming frequencies, it could be perceivable some audible noise from the input and output capacitors of the boost converter. These micro-mechanical vibrations are an effect of the subharmonics produced from the boost switching frequency. In order to minimize this effect plus slightly improve the efficiency of the system, it is recommended to replace the following components: Schematic Designator Device Type Description Manufacturer PN Capacitors C2 10UF CC1210 CAP CER 10UF 50V +/-10% X7R 1210 GJ832ER7YA106KA12L C3 4.7uF CC1206 CAP CER 4.7UF 50V +/-10% X7R 1206 GJ831CR71H475KA12L C4 DNP - - - C5 DNP - - - 10UF ind_ihlp_2525 IND PWR 10UH@100KHZ 2.3A 20% SMT IHLP2525CZER100M01 Inductor L1 Freescale does not assume liability, endorse, or warrant components from external manufacturers that are referenced in circuit drawings or tables. While Freescale offers component recommendations in this configuration, it is the customer's responsibility to validate their application KIT34845EPEVME Evaluation Board, Rev. 1.0 22 Freescale Semiconductor References 14 References Following are URLs where you can obtain information on other Freescale products and application solutions: Description URL Data Sheet www.freescale.com/files/analog/doc/data_sheet/MC34845.pdf Freescale's Web Site www.freescale.com Freescale's Analog Web Site www.freescale.com/analog Freescale's Power Management Web Site www.freescale.com/pm Freescale's LED Drivers www.freescale.com/webapp/sps/site/taxonomy.jsp?code=LEDBLDRIVER KIT34845EPEVME Evaluation Board, Rev. 1.0 Freescale Semiconductor 23 Revision History 15 Revision History REVISION 1.0 DATE 10/2008 DESCRIPTION OF CHANGES * Initial Release KIT34845EPEVME Evaluation Board, Rev. 1.0 24 Freescale Semiconductor How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 10 5879 8000 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc. 2009. All rights reserved. KT34845UG Rev. 1.0 6/2009