LM193 LM293 - LM393 LOW POWER DUAL VOLTAGE COMPARATORS WIDE SINGLE SUPPLY VOLTAGE RANGE OR DUAL SUPPLIES : +2V TO +36V OR 1V TO 18V VERY LOW SUPPLY CURRENT (0.4mA) INDEPENDENT OF SUPPLY VOLTAGE (1mW/comparator at +5V) N DIP8 (Plastic Package) LOW INPUT BIAS CURRENT : 25nA TYP LOW INPUT OFFSET CURRENT : 5nA TYP LOW INPUT OFFSET VOLTAGE : 1mV TYP D SO8 (Plastic Micropackage) INPUT COMMON-MODE VOLTAGE RANGE INCLUDES GROUND LOW OUTPUT SATURATION VOLTAGE : 250mV TYP. (Io = 4mA) DIFFERENTIAL INPUT VOLTAGE RANGE P TSSOP8 (Thin Shrink Small Outline Package) EQUAL TO THE SUPPLY VOLTAGE TTL, DTL, ECL, MOS, CMOS COMPATIBLE OUTPUTS S Mini SO8 (Plastic Micropackage) DESCRIPTION ORDER CODE These devices consist of two independent low voltage comparators designed specifically to operate from a single supply over a wide range of voltages. Operation from split power supplies is also possible. These comparators also have a unique characteristic in that the input common-mode voltage range includes ground even though operated from a single power supply voltage. Part Number Temperature Range LM193 -55C, +125C LM293 -40C, +105C LM393 0C, +70C Example : LM393D Package N D P S * * * * * * * * * * * * N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) P = Thin Shrink Small Outline Package (TSSOP) - only available in Tape &Reel (PT) S = MiniSO Package (MiniSO) only available in Tape & Reel (ST) PIN CONNECTIONS (top view) 1 2 - 3 + 4 July 2002 8 7 - 6 + 5 1 2 3 4 5 6 7 8 - Output 1 - Inverting input 1 - Non-inverting input 1 - VCC- Non-inverting input 2 - Inverting input 2 - Output 2 - VCC+ 1/11 LM193-LM293-LM393 SCHEMATIC DIAGRAM (1/2 LM193) VCC 3.5A 100A 3.5A 100A Non-inverting Input VCC VO VCC Inverting Input VCC ABSOLUTE MAXIMUM RATINGS Symbol Parameter VCC Supply voltage Vid Differential Input Voltage Vi Input Voltage Output Short-circuit to Ground - note Power Dissipation 2) Pd Tstg 1) DIP8 SO8 TSSOP8 Mini SO8 Storage Temperature Range Value Unit 18 or 36 V 36 V -0.3 to +36 V Infinite 1250 710 625 580 mW -65 to +150 C Short-circuits from the output to V CC + can cause excessive heating and eventual destruction. The maximum output current is approximately 20mA independent of the magnitude of V CC +. Pd is calculated with T amb = +25C, Tj = +150C and R thja = 100C/W for DIP8 package = 175C/W for SO8 package = 200C/W for TSSOP8 package = 215C/W for Mini SO8 package 1. 2. OPERATING CONDITIONS Symbol Parameter Vicm Common Mode Input Voltage Range Toper Operating Free-Air Temperature range LM193 LM293 LM393 2/11 Value + Unit 0 to VCC -1.5 V -55 to +125 -40 to +125 0 to +70 C LM193-LM293-LM393 ELECTRICAL CHARACTERISTICS VCC+ = +5V, VCC-= 0V, Tamb = +25C (unless otherwise specified) Symbol Parameter Min Typ. Max. Unit Vio Input Offset Voltage - note 1) Tamb = +25C Tmin Tamb Tmax 1 5 9 mV Iib Input Bias Current - note 2) Tamb = +25C Tmin Tamb Tmax 25 250 400 nA Iio Input Offset Current Tamb = +25C Tmin Tamb Tmax 5 50 150 nA Avd Large Signal Voltage Gain VCC = 15V, R L = 15k, Vo = 1V to 11V ICC Supply Current (all comparators) VCC = 5V, no load VCC = 30V, no load Vicm Input Common Mode Voltage Range - note 3) Tamb = +25C Tmin Tamb Tmax Vid 50 200 V/mV 0.4 1 0 0 1 2.5 mA V CC+ -1.5 V VCC+ -2 VCC+ Differential Input Voltage -note 4) Isink Output Sink Currrent Vid= 1V, Vo = 1.5V V OL Low Level Output Voltage Vid = -1V, Isink = 4mA Tamb = +25C Tmin Tamb Tmax 6 16 V mA 250 400 700 mV High Level Output Current (Vid = 1V) IOH 1. 2. 3. 4. 5. Vid = 1V, VCC = Vo = 30V Tamb = +25C Tmin Tamb Tmax tre Response Time - note 5) R L= 5.1k to VCC+ trel Large Signal Response Time Vi = TTL, V(ref) = +1.4V, RL= 5.1k to VCC+ 0.1 1 nA A s 1.3 300 ns At output switch point, Vo 1.4V, R s = 0 with VCC from 5V to 30V, and over the full common-mode range (0V to VCC -1.5V). The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output, so no loading charge exists on the reference of input lines. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC + -1.5V, but either or both inputs can go to +30V without damage Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the comparator will provide a proper output state. The low input voltage state must not be less than -0.3V (or 0.3V bellow the negative power supply, if used). The response time specified is for a 100mV input step with 5mV overdrive. For larger overdrive signals 300ns can be obtained + + 3/11 LM193-LM293-LM393 SUPPLY CURRENTversus SUPPLY VOLTAGE INPUT CURRENT versus SUPPLY VOLTAGE 80 INPUT CURRENT (nA) Tamb = 0C 0.8 Tamb= +25C 0.6 T amb = +70C 0.4 Tamb = +125C 0.2 R = 0 10 20 30 SUPPLY VOLTAGE (V) 0 -1 Tamb = -55C 10 10 -2 Tamb= +25C -2 10 -1 10 0 10 1 10 OUTPUT SINK CURRENT (mA) RESPONSE TIME FOR VARIOUS INPUT OVERDRIVES - POSITIVE TRANSITION INPUT VOLTAGE (mV) Tamb= +25C 20 Tamb = +125C Tamb = +70C 10 20 30 SUPPLY VOLTAGE (V) 40 6 5 4 3 2 1 0 0 -50 -100 Input overdrive : 5mV 5V 5.1k 20mV eI eo 100mV Tamb= +25C -3 10 6 1 5 4 3 2 1 0 00 50 0 OUTPUT VOLTAGE (V) Tamb = 0C 40 1 Tamb = +125C 10 Tamb = -55C i RESPONSE TIME FOR VARIOUS INPUT OVERDRIVES - NEGATIVE TRANSITION Out of saturation 10 R = 10 9 0 INPUT VOLTAGE (mV) SATURATION VOLTAGE (V) 10 60 40 OUTPUT SATURATION VOLTAGE versus OUTPUT CURRENT Input overdrive : 100mV 5mV 20mV 5V 5.1k eI eo Tamb = +25C 0 4/11 Vi = 0V Tamb = -55C OUTPUT VOLTAGE (V) SUPPLY CURRENT (mA) 1 0.5 1 1.5 TIME ( s) 2 2 0 0.5 1 1.5 TIME (s) 2 LM193-LM293-LM393 TYPICAL APPICATIONS BASIC COMPARATOR DRIVING CMOS 5V VCC = 5V 15k +V(ref) 100k +V(ref) 1/2 LM193 VO -V(ref) DRIVING TTL & 1/2 LM193 -V(ref) LOW FREQUENCY OP AMP 5V 5V 15k 1/2 LM193 10k +V(ref) ~ 1/2 LM193 & eo 100k -V(ref) & LOW FREQUENCY OP AMP (e o = 0V for e I = 0V) A V = 100 5V 5V 1/2 LM193 eI 0.5F 1k TRANSDUCER AMPLIFIER Magnetic pick-up 15k ~ eI 2N 2222 10k 3k 1/2 LM193 0.5 F eo 20M 100k 1k eo A V = 100 10k 5/11 LM193-LM293-LM393 LOW FREQUENCY OP AMP WITH OFFSET ADJUST ZERO CROSSING DETECTOR (single power supply) 5V 5V Offset Adjust 100k 5V Rs eI 1M 1M R2 100k RI eI 15k 1/2 LM193 ~ 5.1k 100k 5.1k 5.1k 2N 2222 1/2 LM193 1N4148 0.5F R1 100k 20M 1k 10k eo TWO-DECADE HIGH-FREQUENCY VCO VCC 100k VCC 3k 5.1k 500pF 1/2 LM193 Frequency control voltage input vcontrol 100k 3k 1/2 LM193 0.01 F 0.1F Output 1 VCC /2 20k Output 2 20k 50k 1/2 LM193 VCC /2 VCC = +30V +250mV Vcontrol +50V 700 Hz fo 100kHz LIMIT COMPARATOR CRYSTAL CONTROLLED OSCILLATOR VCC (12V) 2R S VCC = 15V 10k 200k V(ref) 1/2 LM193 high eI 6/11 0.1F 1/2 LM193 ~ 2R S V(ref) low VCC Lamp RS 2k 100k 1/2 LM193 f = 100kHz 2N 2222 200k eo 0 LM193-LM293-LM393 SPLIT-SUPPLY APPLICATIONS ZERO CROSSING DETECTOR COMPARATOR WITH A NEGATIVE REFERENCE 15V 15V 5.1k 5.1k 1/2 LM193 eI 1/2 LM193 eo eI ~ eo ~ 5V 15V 15V 7/11 LM193-LM293-LM393 PACKAGE MECHANICAL DATA 8 PINS - PLASTIC DIP Millimeters Inches Dimensions Min. A a1 B b b1 D E e e3 e4 F i L Z 8/11 Typ. Max. Min. 3.32 0.51 1.15 0.356 0.204 0.020 0.045 0.014 0.008 0.065 0.022 0.012 0.430 0.384 0.313 2.54 7.62 7.62 3.18 Max. 0.131 1.65 0.55 0.304 10.92 9.75 7.95 Typ. 0.100 0.300 0.300 6.6 0260 5.08 3.81 1.52 0.200 0.150 0.060 0.125 LM193-LM293-LM393 PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO) s b1 b a1 A a2 C c1 a3 L E e3 D M 5 1 4 F 8 Millimeters Inches Dimensions Min. A a1 a2 a3 b b1 C c1 D E e e3 F L M S Typ. Max. 0.65 0.35 0.19 0.25 1.75 0.25 1.65 0.85 0.48 0.25 0.5 4.8 5.8 5.0 6.2 0.1 Min. Typ. Max. 0.026 0.014 0.007 0.010 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.189 0.228 0.197 0.244 0.004 45 (typ.) 1.27 0.050 3.81 3.8 0.4 0.150 4.0 1.27 0.6 0.150 0.016 0.157 0.050 0.024 8 (max.) 9/11 LM193-LM293-LM393 PACKAGE MECHANICAL DATA 8 PINS - THIN SHRINK SMALL OUTLINE PACKAGE k c 0.25mm .010 inch GAGE PLANE L1 L L L1 C SEATING PLANE E1 A E A2 A1 5 4 4 5 D b e 8 1 8 1 PIN 1 IDENTIFICATION Millimeters Inches Dimensions Min. A A1 A2 b c D E E1 e k l L L1 0.05 0.80 0.19 0.09 2.90 4.30 0 0.50 0.45 Typ. 1.00 3.00 6.40 4.40 0.65 0.60 0.600 1.000 Max. Min. 1.20 0.15 1.05 0.30 0.20 3.10 0.01 0.031 0.007 0.003 0.114 4.50 0.169 8 0.75 0 0.09 0.75 0.018 Typ. 0.039 0.118 0.252 0.173 0.025 0.0236 0.024 0.039 Max. 0.05 0.006 0.041 0.15 0.012 0.122 0.177 8 0.030 0.030 10/11 LM193-LM293-LM393 PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (miniSO) k 0,25mm .010inch c C PLANE SEATING E1 L1 L GA GEPLANE A E A2 A1 4 8 1 e C ccc b D 5 PIN1IDENTIFICA TION Millimeters Inches Dimensions A A1 A2 b c D E E1 e L L1 k aaa Min. Typ. 0.050 0.780 0.250 0.130 2.900 4.750 2.900 0.100 0.860 0.330 0.180 3.000 4.900 3.000 0.650 0.550 0.950 3d 0.400 0d Max. Min. Typ. 1.100 0.150 0.940 0.400 0.230 3.100 5.050 3.100 0.002 0.031 0.010 0.005 0.114 0.187 0.114 0.700 0.016 6d 0.100 0d 0.004 0.034 0.013 0.007 0.118 0.193 0.118 0.026 0.022 0.037 3d Max. 0.043 0.006 0.037 0.016 0.009 0.122 0.199 0.122 0.028 6d 0.004 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibil ity for the consequences of use of such information nor for any infring ement of patents or other righ ts of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change witho ut notice. This publ ication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life suppo rt devices or systems withou t express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 2002 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Swit zerland - United Kingdom - United States http://www. st.com 11/11