(888) IPD-CONVerters (888) 473-2668 www.ipdconverters.com OWT SERIES - TRIPLE OUTPUT, 25 WATT FEATURES DESCRIPTION OWT triple output DC/DC converters provide up to * Industry Standard 25 Watts of output power in an industry standard 2" x 2" Package package. OWT units feature excellent efficiency, five* 12V Input sided shielding, and fixed switching frequency. With * 25W Output 85C case operation, the OWT is especially suited to telecom, networking, and industrial applications. * * * * External Enable Pin 5-Sided Shielding 500V Isolation 85C Case Operation Efficiency vs. Load (24V Input) 85 80 EFFICIENCY % 75 TECHNICAL SPECIFICATIONS 65 OWT2405-12 OWT2405-15 60 55 Input Voltage Range 12 VDC Nominal 24 VDC Nominal 48 VDC Nominal Input Ripple Current Reverse Input Current 70 50 10 - 20 VDC 18 - 36 VDC 20 - 60 (add -S1 to p/n) or 36 - 72 VDC 20% Iin Max. 100% Iin Max. 10 20 30 40 50 60 70 80 90 100 LOAD % Efficiency vs. Load (48V Input) Output 85 Setpoint Accuracy, Vout1 / Vout2 / Vout3 1%, 5%, 5% Line regulation Vin Min. - Vin Max., Iout Rated 1% Vout Load regulation Iout Min.- I out Max., V in Nom., Vout1 / Vout2 / Vout3 1%, 5%, 5% Minimum Output Current 25 % Dynamic Regulation, Loadstep 25% Iout Pk Deviation 4% Vout Settling Time 500 s Short Circuit / Overcurrent Protection Continuous Current Limit Threshold Range, % of Iout Rated 130% 80 EFFICIENCY % 75 70 OWT4805-12 65 OWT4805-15 60 55 50 10 General Remote Shutdown Remote Shutdown Reference Switching Frequency Isolation Input - Output Input - Case Output - Case Temperature Coefficient Case Temperature Operating Range Storage Range Humidity Max., Non-Condensing Vibration, 3 Axes, 5 Min Each MTBF (Bellcore TR-NWT-000332) Safety Rev. 05/01 20 30 40 50 60 70 80 90 100 LOAD % Positive Vin Negative 300 kHz Notes 500 VDC 500 VDC 500 VDC 0.02%/C 1 Industrial temp range of -40 to +85C available, add suffix -I to P/N MTBF predictions may vary slightly from model to model. Specifications typically at 25C, normal line, and full load, unless otherwise stated. -25 to +60C1 -40 to +125C 95% 5 g, 10 -55 Hz 1.8 x 106 hrs UL 1950, CSA 22.2-950, EN60950 Soldering Conditions: I/O pins, 260C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information. 1 OWT SERIES - TRIPLE OUTPUT, 25 WATT MODELS - (See the last page of Section for options.) Vin (Volts) Vin Range (Volts) Iin Max.* (Amps) 12 12 24 24 48 48 48 WIDE 48 WIDE 10 - 20 10 - 20 18 - 36 18 - 36 20 - 60 20 - 60 36 - 72 36 - 72 3.7 3.7 2.4 2.4 2.3 2.3 1.4 1.4 Vout (Volts) Iout Rated (Amps) 5, 5, 5, 5, 5, 5, 5, 5, 3.5, 3.5, 3.5, 3.5, 3.5, 3.5, 3.5, 3.5, 12 15 12 15 12 15 12 15 Ripple & Noise Pk-Pk (mV) 0.31 0.25 0.31 0.25 0.31 0.25 0.31 0.25 50, 50, 50, 50, 50, 50, 50, 50, 120 150 120 150 120 150 120 150 Efficiency Typ. ** Model 78% 79% 81% 82% 81% 82% 81% 82% OWT1205-12 OWT1205-15 OWT2405-12 OWT2405-15 OWT4805-12S1 OWT4805-15S1 OWT4805-12 OWT4805-15 * Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output. MECHANICAL DRAWING 0.18" MIN. 2.00" (50.8mm) 0.600"(15.2mm) (4.6mm) 1 0.400"(10.2mm) 2 0.200"(5.1mm) 3 0 4 5 1.100"(27.9mm) 6 0.700"(17.8mm) DIA 0.040" (1.0mm) 2.00" BOTTOM VIEW (50.8mm) 7 0.300"(7.6mm) 8 -0.100"(-2.5mm) -0.50"(-12.7mm) 1.800" -0.10" 0 (-2.5mm) (45.7mm) 0.50" (12.7mm) Thermal Impedance Natural Convection 100 LFM 200 LFM 300 LFM 400 LFM 14.9 11.3 8.3 6.8 5.4 Pin C/W C/W C/W C/W C/W Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application. Tolerances Function 1 2 3 4 5 6 7 8 +Vin -Vin No Conn. Enable + Aux Out +5V Out Common - Aux Out 2 Inches: .XX 0.040 .XXX 0.010 Pin: 0.002 (Millimeters) .X 1.0 .XX 0.25 0.05 (Dimensions as listed unless otherwise specified.) OPTIONS Powering Communications and Technology When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table. OPTIONS SUFFIX APPLICABLE SERIES Negative Logic N HAS, HBD, HBS, HES, HLS, LES, QBS, QES, QLS, TES, TQD Lucent Compatible Trim T HAS, HBD, HBS, HES, HLS, QBS, QES, QLS Terminal Strip TS XWS, XWD, XWT REMARKS TTL "Low" Turns Module ON TTL "High" Turns Module OFF Trim 1 IAS, LES Enable 2 IAD, IAS, LES, SMS Trim and Enable 3 IAS, LES Current Share 4 SMS Headerless PIN LENGTH AND HEATSINK OPTIONS Y Encapsulated EWS, IWS, OWS 0.110" (2.8mm) Pin Length 8 All Units (Except SMS) 0.150" (3.8mm) Pin Length 9 1H All Units (Except SMS) All Units (Except DIP, HLS, HLD, QLS, SIP, SM TLD, and TKD Packages) Includes Thermal Pad 1V All Units (Except DIP, HLS, HLD, QLS, SIP, SM TLD, and TKD Packages) Includes Thermal Pad 2H All Units (Except DIP, HLS, HLD, QLS, SIP, SM TLD, and TKD Packages) Includes Thermal Pad 2V All Units (Except DIP, HLS, HLD, QLS, SIP, SM TLD, and TKD Packages) Includes Thermal Pad 0.95" (24.1mm) Horizontal Heatsink 3H All Units (Except DIP, HLS, HLD, QLS, SIP, SM TLD, and TKD Packages) Includes Thermal Pad 0.95" (24.1mm) Vertical Heatsink 3V All Units (Except DIP, HLS, HLD, QLS, SIP, SM TLD, and TKD Packages) Includes Thermal Pad 0.24" (6.1mm) Horizontal Heatsink 0.24" (6.1mm) Vertical Heatsink 0.45" (11.4mm) Horizontal Heatsink 0.45" (11.4mm) Vertical Heatsink Standard Pin Length is 0.180" (4.6mm) Example Options: HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and 0.95" vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110" pin length. NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. 3