General Description
The MAX7500–MAX7504 temperature sensors accu-
rately measure temperature and provide an overtem-
perature alarm/interrupt/shutdown output. These
devices convert the temperature measurements to digi-
tal form using a high-resolution, sigma-delta, analog-to-
digital converter (ADC). Communication is through an
I2C∗-compatible 2-wire serial interface. The MAX7500/
MAX7501/MAX7502 integrate a timeout feature that
offers protection against I2C bus lockups. The
MAX7503/MAX7504 do not include the timeout feature.
The 2-wire serial interface accepts standard write byte,
read byte, send byte, and receive byte commands to
read the temperature data and configure the behavior
of the open-drain overtemperature shutdown output.
The MAX7500 features three address select lines, while
the MAX7501–MAX7504 feature two address select
lines and a RESET input. The MAX7500/MAX7501/
MAX7502s’ 3.0V to 5.5V supply voltage range, low
250µA supply current, and a lockup-protected I2C-com-
patible interface make them ideal for a wide range of
applications, including personal computers (PCs), elec-
tronic test equipment, and office electronics.
The MAX7500–MAX7504 are available in 8-pin µMAX®
and SO packages and operate over the -55°C to
+125°C temperature range.
Applications
PCs
Servers
Office Electronics
Electronic Test Equipment
Industrial Process Control
Features
♦Timeout Prevents Bus Lockup (MAX7500,
MAX7501, MAX7502)
♦Hardware Reset for Added Protection
♦I2C Bus Interface
♦3.0V to 5.5V Supply Voltage Range
♦250µA (typ) Operating Supply Current
♦3µA (typ) Shutdown Supply Current
♦±2°C (max) from -25°C to +100°C Temperature
Accuracy
♦µMAX, SO Packages Save Space
♦Separate Open-Drain OS Output Operates as
Interrupt or Comparator/Thermostat Input
♦Register Readback Capability
♦Improved LM75 Second Source
♦UL Certified
MAX7500–MAX7504
Digital Temperature Sensors and Thermal
Watchdog with Bus Lockup Protection
________________________________________________________________ Maxim Integrated Products 1
1
2
3
4
8
7
6
5
+VS
A0
A1
A2GND
OS
SCL
SDA
MAX7500
µMAX, SO
1
2
3
4
8
7
6
5
+VS
A0
A1
RESETGND
OS
SCL
SDA
MAX7501–
MAX7504
µMAX, SO
TOP VIEW
Pin Configurations
Ordering Information/
Selector Guide
19-3382; Rev 2; 6/05
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
PART TEMP
RANGE
PIN-
PACKAGE
RESET
TIMEOUT
MAX7500MSA
-55°C to
+125°C
8 SO X X
MAX7500MSA+
-55°C to
+125°C
8 SO X X
MAX7500MUA
-55°C to
+125°C
8 µMAX X X
MAX7500MUA+
-55°C to
+125°C
8 µMAX X X
*Purchase of I2C components from Maxim Integrated Products
Inc., or one of its sublicensed Associated Companies, conveys
a license under Philips I2C Patent Rights to use these compo-
nents in an I2C system, provided that the system conforms to
the I2C Standard Specification as defined by Philips.
Ordering Information/Selector Guide continued at end of
data sheet.
+Denotes lead-free package.
µMAX is a registered trademark of Maxim Integrated Products,
Inc.
MAX7500–MAX7504
Digital Temperature Sensors and Thermal
Watchdog with Bus Lockup Protection
2_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(+VS = +3.0V to +5.5V, TA= -55°C to +125°C, unless otherwise noted. Typical values are at +VS= +3.3V, TA= +25°C.) (Notes 4, 5)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifica-
tions do not apply when operating the device beyond its rated operating conditions.
Note 2: When the input voltage (VI) at any pin exceeds the power supplies (VI< GND or VI> + VS), the current at that pin should be
limited to 5mA. The 20mA maximum package input current rating limits the number of pins that can safely exceed the power
supplies with an input current of 5mA to 4.
Note 3: Human Body Model, 100pF discharged through a 1.5kΩresistor.
(Note 1)
+VSto GND ............................................................. -0.3V to +6V
OS, SDA, SCL to GND.......................................... -0.3V to +6.0V
All Other Pins to GND................................ -0.3V to (+VS+ 0.3V)
Input Current at Any Pin (Note 2) ..................................... +5mA
Package Input Current (Note 2) ..................................... +20mA
ESD Protection (all pins, Human Body Model, Note 3)... ±2000V
Continuous Power Dissipation (TA = +70°C)
8-Pin µMAX (derate 4.5mW/°C above +70°C) ............ 362mW
8-Pin SO (derate 5.9mW/°C above +70°C)................. 471mW
Operating Temperature Range ....................... -55°C to +125°C
Junction Temperature .................................................... +150°C
Storage Temperature Range ........................... -65°C to +150°C
Lead Temperature (soldering, 10s) ............................... +300°C
PARAMETER
SYMBOL
CONDITIONS
TYP
UNITS
-25°C ≤ TA ≤ +100°C
±2.0
Accuracy -55°C ≤ TA ≤ +125°C
±3.0
°C
Resolution 9bits
Conversion Time (Note 6)
100
ms
I2C inactive
0.25
0.5 mA
Shutdown mode, +VS = 3V 3Quiescent Supply Current
Shutdown mode, +VS = 5V 5 µA
+VS Supply Voltage Range 3.0 5.5 V
OS Output Saturation Voltage IOUT = 4.0mA (Note 7) 0.8 V
OS Delay (Note 8) 1 6 Conver-
sions
TOS Default Temperature (Note 9) 80 °C
THYST Default Temperature (Note 9) 75 °C
LOGIC (SDA, SCL, A0, A1, A2)
Input High Voltage VIH +VS x
0.7 V
Input Low Voltage VIL +VS x
0.3 V
Input High Current IIH VIN = 5V
0.005
1.0 µA
Input Low Current IIL VIN = 0V
0.005
1.0 µA
Input Capacitance All digital inputs 5 pF
Output High Current VIN = 5V 1 µA
Output Low Voltage IOL = 3mA 0.4 V
MAX7500–MAX7504
Digital Temperature Sensors and Thermal
Watchdog with Bus Lockup Protection
_______________________________________________________________________________________ 3
Note 4: All parts operate properly over the +VS= 3V to 5V supply voltage range. The devices are tested and specified for rated
accuracy at their nominal supply voltage. Accuracy typically degrades 1°C per volt of change in +VSas it varies from the
nominal value.
Note 5: All parameters are measured at +25°C. Values over the temperature range are guaranteed by design.
Note 6: This specification indicates how often temperature data is updated. The devices can be read at any time without regard
to conversion state, while yielding the last conversion result.
Note 7: For best accuracy, minimize output loading. Higher sink currents can affect sensor accuracy due to internal heating.
Note 8: OS delay is user programmable up to six “over-limit” conversions before OS is set to minimize false tripping in noisy
environments.
Note 9: Default values set at power-up.
Note 10: All timing specifications are guaranteed by design.
Note 11: A master device must provide a hold time of at least 300ns for the SDA signal to bridge the undefined region of SCL’s
falling edge.
Note 12: CB= total capacitance of one bus line in pF. Tested with CB= 400pF.
Note 13: Input filters on SDA, SCL, and A_ suppress noise spikes less than 50ns.
Note 14: Holding the SDA line low for a time greater than tTIMEOUT causes the devices to reset SDA to the IDLE state of the serial
bus communication (SDA set high).
ELECTRICAL CHARACTERISTICS (continued)
(+VS = +3.0V to +5.5V, TA= -55°C to +125°C, unless otherwise noted. Typical values are at +VS= +5V, TA= +25°C.) (Notes 4, 5)
PARAMETER
SYMBOL
CONDITIONS
TYP
UNITS
I2C-COMPATIBLE TIMING (Note 10)
Serial Clock Frequency fSCL Bus timeout inactive DC 400 kHz
Minimum RESET Pulse Width 1 µs
Bus Free Time Between STOP
and START Conditions tBUF 1.3 µs
START Condition Hold Time tHD:STA 0.6 µs
STOP Condition Setup Time tSU:STO 90% of SCL to 10% of SDA 100 ns
Clock Low Period tLOW 1.3 µs
Clock High Period tHIGH 0.6 µs
START Condition Setup Time tSU:STA 90% of SCL to 90% of SDA 100 ns
Data Setup Time tSU:DAT 10% of SDA to 10% of SCL 100 ns
Data Hold Time
tHD:DAT
10% of SCL to 10% of SDA (Note 11) 0 0.9 µs
Maximum Receive SCL/SDA Rise
Time tR
300
ns
Minimum Receive SCL/SDA Rise
Time tR(Note 12)
20 +
0.1 x
CB
ns
Maximum Receive SCL/SDA Fall
Time tF
300
ns
Minimum Receive SCL/SDA Fall
Time tF(Note 12)
20 +
0.1 x
CB
ns
Transmit SDA Fall Time tF(Note 12)
20 +
0.1 x
CB
250 ns
Pulse Width of Suppressed Spike
tSP (Note 13) 0 50 ns
SDA Time Low for Reset of Serial
Interface
tTIMEOUT
MAX7500/MAX7501/MAX7502 (Note 14) 150 300 ms
MAX7500–MAX7504
Digital Temperature Sensors and Thermal
Watchdog with Bus Lockup Protection
4_______________________________________________________________________________________
Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
QUIESCENT SUPPLY CURRENT
vs. TEMPERATURE
MAX7500 toc01
TEMPERATURE (°C)
QUIESCENT SUPPLY CURRENT (µA)
9565355-25
240
250
260
270
280
290
300
230
-55 125
+VS = +5V
+VS = +3V
SHUTDOWN SUPPLY CURRENT (µA)
1
2
3
4
5
6
0
SHUTDOWN SUPPLY CURRENT
vs. TEMPERATURE
MAX7500 toc02
TEMPERATURE (°C)
9565355-25-55 125
+VS = +5V
+VS = +3V
ACCURACY vs. TEMPERATURE
ACCURACY (°C)
-1.5
-1.0
-0.5
0
0.5
1.0
1.5
2.0
-2.0
MAX7500 toc03
TEMPERATURE (°C)
9565355-25-55 125
4 TYPICAL PARTS
Pin Description
PIN
MAX7500
MAX7501–
MAX7504
NAME FUNCTION
11SDA Serial Data Input/Output Line. Open drain. Connect SDA to a pullup resistor.
22SCL Serial Data Clock Input. Open drain. Connect SCL to a pullup resistor.
33OS Overtemperature Shutdown Output. Open drain. Connect OS to a pullup resistor.
44GND Ground
5—A2
2-Wire Interface Address Input. Connect A2 to GND or +VS to set the desired I2C bus
address. Do not leave floating (see Table 1).
—5RESET Active-Low Reset Input. Pull RESET low for longer than the minimum reset pulse width
to reset the I2C bus and all internal registers to their POR values.
66A1
2-Wire Interface Address Input. Connect A1 to GND or +VS to set the desired I2C bus
address. Do not leave floating (see Table 1).
77A0
2-Wire Interface Address Input. Connect A0 to GND or +VS to set the desired I2C bus
address. Do not leave floating (see Table 1).
88+V
SPositive Supply Voltage Input. Bypass to GND with a 0.1µF bypass capacitor.
Detailed Description
The MAX7500–MAX7504 temperature sensors measure
temperature, convert the data into digital form using a
sigma-delta ADC, and communicate the conversion
results through an I2C-compatible 2-wire serial inter-
face. These devices accept standard I2C commands to
read the data, set the overtemperature alarm (OS) trip
thresholds, and configure other characteristics. The
MAX7500 features three address select lines (A0, A1,
A2) while the MAX7501–MAX7504 feature two address
select lines (A0, A1) and a RESET input. The
MAX7500–MAX7504 operate from +3.0V to +5.5V sup-
ply voltages and consume 250µA of supply current.
MAX7500–MAX7504
Digital Temperature Sensors and Thermal
Watchdog with Bus Lockup Protection
_______________________________________________________________________________________ 5
I2C-Compatible Bus Interface
From a software perspective, the MAX7500–MAX7504
appear as a set of byte-wide registers that contain tem-
perature data, alarm threshold values, and control bits.
A standard I2C-compatible 2-wire serial interface reads
temperature data and writes control bits and alarm
threshold data. Each device responds to its own I2C
slave address, which is selected using A0, A1, and A2.
See Table 1.
The MAX7500–MAX7504 employ four standard I2C
protocols: write byte, read byte, send byte, and receive
byte (Figures 1, 2, and 3). The shorter receive byte pro-
tocol allows quicker transfers, provided that the correct
data register was previously selected by a read-byte
instruction. Use caution when using the shorter proto-
cols in multimaster systems, as a second master could
overwrite the command byte without informing the first
master. The MAX7500 has eight different slave
addresses available; therefore, a maximum of eight
MAX7500 devices can share the same bus. The
MAX7501–MAX7504 each have four different slave
addresses available.
DEVICE BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
MAX7500 1 0 0 1 A2 A1 A0 RD/W
MAX7501 1 0 0 1 1 A1 A0 RD/W
MAX7502 1 0 0 1 0 A1 A0 RD/W
MAX7503 1 0 0 1 1 A1 A0 RD/W
MAX7504 1 0 0 1 0 A1 A0 RD/W
Table 1. I2C Slave Addresses
tBUF
tSU:STO
tHD:STA
tSU:STA
tHD:DAT
tHIGH
tLOW
tSU:DAT
tHD:STA
SCL
SDA
tF
tR
ACKNOWLEDGE
(A)
STOP
CONDITION
(P)
START
CONDITION
(S)
START
CONDITION
(S)
REPEATED START
CONDITION
(SR)
PARAMETERS ARE MEASURED FROM 10% TO 90%.
Figure 1. Serial Bus Timing
MAX7500–MAX7504
Digital Temperature Sensors and Thermal
Watchdog with Bus Lockup Protection
6_______________________________________________________________________________________
ADDRESS
BYTE
ADDRESS
BYTE
ADDRESS
BYTE
(a) TYPICAL POINTER SET FOLLOWED BY IMMEDIATE READ FROM CONFIGURATION REGISTER
(b) CONFIGURATION REGISTER WRITE
(c) THIGH AND TLOW WRITE
POINTER
BYTE
POINTER
BYTE
POINTER
BYTE MOST-SIGNIFICANT
DATA BYTE
LEAST-SIGNIFICANT
DATA BYTE
CONFIGURATION
BYTE
ADDRESS
BYTE
DATA
BYTE
ACK BY
MAX7500–
MAX7504
ACK BY
MAX7500–
MAX7504
ACK BY
MAX7500–
MAX7504 ACK BY
MAX7500–
MAX7504
ACK BY
MAX7500–
MAX7504
ACK BY
MAX7500–
MAX7504
ACK BY
MAX7500–
MAX7504
START
BY
MASTER
START
BY
MASTER
START
BY
MASTER
REPEAT
START
BY
MASTER
NO
ACK BY
MASTER
STOP
COND BY
MASTER
ACK BY
MAX7500–
MAX7504
ACK BY
MAX7500–
MAX7504
STOP
COND BY
MASTER
STOP
COND BY
MASTER
ACK BY
MAX7500–
MAX7504
Figure 2. I2C-Compatible Timing Diagram (Write)
MAX7500–MAX7504
Digital Temperature Sensors and Thermal
Watchdog with Bus Lockup Protection
_______________________________________________________________________________________ 7
ADDRESS
BYTE
ADDRESS BYTE
ADDRESS
BYTE
ADDRESS
BYTE
DATA
BYTE
(a) TYPICAL 2-BYTE READ FROM PRESET POINTER LOCATION SUCH AS TEMP, THIGH, TLOW.
(b) TYPICAL POINTER SET FOLLOWED BY IMMEDIATE READ FOR 2-BYTE REGISTER SUCH AS TEMP, THIGH, TLOW.
(c) TYPICAL 1-BYTE READ FROM CONFIGURATION REGISTER WITH PRESET POINTER.
MOST-SIGNIFICANT
DATA BYTE
LEAST-SIGNIFICANT
DATA BYTE
POINTER BYTE
MOST-SIGNIFICANT
DATA BYTE
LEAST-SIGNIFICANT
DATA BYTE
ACK BY
MAX7500–
MAX7504
ACK BY
MASTER
ACK BY
MAX7500–
MAX7504
ACK BY
MAX7500–
MAX7504
ACK BY
MASTER
ACK BY
MAX7500–
MAX7504
ACK BY
MASTER
START
BY
MASTER
START
BY
MASTER
REPEAT
START
BY
MASTER
START
BY
MASTER
STOP
COND BY
MASTER
STOP
COND BY
MASTER
STOP
COND BY
MASTER
NO ACK BY
MASTER
NO
ACK BY
MASTER
NO
ACK BY
MASTER
Figure 3. I2C-Compatible Timing Diagram (Read)
MAX7500–MAX7504
Register Descriptions
The MAX7500–MAX7504 have an internal pnp-junction-
based temperature sensor whose analog output is con-
verted to digital form using a 9-bit sigma-delta ADC.
The measured temperature and temperature configura-
tions are controlled by the temperature, configuration,
THYST, and TOS registers. See Table 2.
Temperature Register
Read the measured temperature through the tempera-
ture register. The temperature data format is 9 bits,
two’s complement, and the register is read out in 2
bytes: an upper byte and a lower byte. Bit D15 is the
sign bit. When bit D15 is 1, the temperature reading is
negative. When bit D15 is zero, the temperature read-
ing is positive. Bits D14–D7 contain the temperature
data, with the LSB representing 0.5°C and the MSB
representing 64°C (see Table 3). The MSB is transmit-
ted first. The last 7 bits of the lower byte, bits D6–D0,
are don’t cares. When reading the temperature register,
bits D6–D0 must be ignored. When the measured tem-
perature is greater than +127.5°C, the value stored in
the temperature register is clipped to 7F8h. When the
measured temperature is below -64°C, the value in the
temperature register is clipped to BF8h.
During the time of reading the temperature register, any
changes in temperature are ignored until the read is
completed. The temperature register is updated upon
completion of the next conversion.
Table 3 lists the temperature register definition.
Configuration Register
The 8-bit configuration register sets the fault queue, OS
polarity, shutdown control, and whether the OS output
functions in comparator or interrupt mode. When writing
to the configuration register, set bits D7, D6, and D5 to
zero. See Table 5.
Bits D4 and D3, the fault queue bits, determine the
number of faults necessary to trigger an OS condition.
See Table 6. The number of faults set in the queue
must occur to trip the OS output. The fault queue pre-
vents OS false tripping in noisy environments.
Set bit D2, the OS polarity bit, to zero to force the OS
output active low. Set bit D2 to 1 to set the OS output
polarity to active high. OS is an open-drain output
under all conditions and requires a pullup resistor to
output a high voltage. See Figure 4.
Set bit D1, the comparator/interrupt bit to zero to run
the overtemperature shutdown block in comparator
mode. In comparator mode, OS is asserted when the
temperature rises above the TOS value. OS is deassert-
Digital Temperature Sensors and Thermal
Watchdog with Bus Lockup Protection
8_______________________________________________________________________________________
REGISTER NAME
ADDRESS (HEX)
POR STATE (HEX)
POR STATE
(BINARY)
POR STATE (°C)
READ/
WRITE
Temperature 00 — — — Read only
Configuration 01 00 0000 0000 — R/W
THYST 02 4B0 0100 1011 0 75 R/W
TOS 03 500 0101 0000 0 80 R/W
Table 2. Register Functions
UPPER BYTE LOWER BYTE
D15
D14 D13 D12 D11 D10 D9 D8
D7
D6 D5 D4 D3 D2 D1
D0
Sign bit
1= Negative
0 = Positive
MSB
64°C32°C16°C8°C4°C2°C1°C
LSB
0.5°C
XXXXXXX
DIGITAL OUTPUT
TEMPERATURE (°C) BINARY hex
+125 0111 1101 0xxx xxxx 7D0x
+25 0001 1001 0xxx xxxx 190x
+0.5 0000 0000 1xxx xxxx 008x
00000 0000 0xxx xxxx 000x
-0.5 1111 1111 1xxx xxxx FF8x
-25 1110 0111 0xxx xxxx E70x
-55 1100 1001 0xxx xxxx C90x
Table 3. Temperature Register Definition
Table 4. Temperature Data Output
X = Don’t care.
ed when the temperature drops below the THYST value.
See Figure 4. Set bit D1 to 1 to run the overtemperature
shutdown block in interrupt mode. OS is asserted in
interrupt mode when the temperature rises above the
TOS value or falls below the THYST value. OS is
deasserted only after performing a read operation.
Set bit D0, the shutdown bit, to zero for normal opera-
tion. Set bit D0 to 1 to shut down the MAX7500–
MAX7504 internal blocks, dropping the supply current
to 3µA. The I2C interface remains active as long as the
shutdown bit is set. The TOS, THYST, and configuration
registers can still be written to and read from while in
shutdown.
TOS and THYST Registers
In comparator mode, the OS output behaves like a ther-
mostat. The output asserts when the temperature rises
above the limit set in the TOS register. The output
deasserts when the temperature falls below the limit set
in the THYST register. In comparator mode, the OS output
can be used to turn on a cooling fan, initiate an emer-
gency shutdown signal, or reduce system clock speed.
In interrupt mode, exceeding TOS also asserts OS. OS
remains asserted until a read operation is performed on
any of the registers. Once OS has asserted due to
crossing above TOS and is then reset, it is asserted
again only when the temperature drops below THYST.
The output remains asserted until it is reset by a read.
Putting the MAX7500–MAX7504 into shutdown mode
also resets OS.
The TOS and THYST registers are accessed with 2
bytes, with bits D15–D7 containing the data. Bits
D6–D0 are don’t cares when writing to these two regis-
ters and read-back zeros when reading from these reg-
isters. The LSB represents 0.5°C while the MSB
represents 64°C. See Table 7.
MAX7500–MAX7504
Digital Temperature Sensors and Thermal
Watchdog with Bus Lockup Protection
_______________________________________________________________________________________ 9
D7 D6 D5 D4 D3 D2 D1 D0
000
Fault queue Fault queue
OS polarity
Comparator/
interrupt Shutdown
Table 5. Configuration Register Definition
D4 D3 NO. OF FAULTS
00 1 (POR state)
01 2
10 4
11 6
Table 6. Configuration Register Fault
Queue Bits
TOS
THYST
OS OUTPUT
(COMPARATOR MODE)
OS SET ACTIVE LOW
OS OUTPUT
(INTERRUPT MODE)
OS SET ACTIVE LOW READ
OPERATION
READ
OPERATION
READ
OPERATION
TEMPERATURE
Figure 4. OS Timing Diagram
UPPER BYTE LOWER BYTE
COMMAND
D15
D14 D13 D12 D11 D10 D9 D8
D7
D6 D5 D4 D3 D2 D1
D0
Write
Sign bit
1 = negative
0 = positive
MSB
64°C32°C16°C8°C4°C2°C1°C
LSB
0.5°CXXXX X X
X
Read
Sign bit
1 = negative
0 = positive
MSB
64°C32°C16°C8°C4°C2°C1°C
LSB
0.5°C0000 0 0
0
Table 7. TOS and THYST Register Definitions
X = Don’t care.
MAX7500–MAX7504
Shutdown
Set bit D0 in the configuration register to 1 to place the
MAX7500–MAX7504 in shutdown mode and reduce
supply current to 3µA.
Power-Up and Power-Down
The MAX7500–MAX7504 power up to a known state, as
indicated in Table 2. Some of these settings are sum-
marized below:
•Comparator mode
•T
OS = +80°C
•T
HYST = +75°C
•OS active low
•Pointer = 00
Internal Registers
The MAX7500–MAX7504s’ pointer register selects
between four data registers. See Figure 5. At power-up,
the pointer is set to read the temperature register at
address 00. The pointer register latches the last loca-
tion to which it was set. All registers are read and write,
except the temperature register, which is read only.
Write to the configuration register by writing an address
byte, a data pointer byte, and a data byte. If 2 data
bytes are written, the second data byte overrides the
first. If more than 2 data bytes are written, only the first
2 bytes are recognized while the remaining bytes are
ignored. The TOS and THYST registers require 1
address byte and 1 pointer byte and 2 data bytes. If
only 1 data byte is written, it is saved in bits D15–D8 of
the respective register. If more than 2 data bytes are
written, only the first 2 bytes are recognized while the
remaining bytes are ignored.
Read from the MAX7500–MAX7504 in one of two ways.
If the location latched in the pointer register is set from
the previous read, the new read consists of an address
byte, followed by retrieving the corresponding number
of data bytes. If the pointer register needs to be set to a
new address, perform a read operation by writing an
address byte, pointer byte, repeat start, and another
address byte.
An inadvertent 8-bit read from a 16-bit register, with the
D7 bit low, can cause the MAX7500–MAX7504 to stop
in a state where the SDA line is held low. Ordinarily, this
would prevent any further bus communication until the
master sends nine additional clock cycles or SDA goes
high. At that time, a stop condition resets the device.
With the MAX7500/MAX7501/MAX7502, if the additional
clock cycles are not generated by the master, the bus
resets and unlocks after the bus timeout period has
elapsed.
The MAX750–MAX7504 can be reset by pulsing RESET
low.
Bus Timeout
Communication errors sometimes occur due to noise
pickup on the bus. In the worst case, such errors can
cause the slave device to hold the data line low, there-
by preventing other devices from communicating over
the bus. The MAX7500/MAX7501/MAX7502s’ internal
bus timeout circuit resets the bus and releases the data
line if the line is low for more than 250ms. When the bus
timeout is active, the minimum serial clock frequency is
limited to 6Hz.
RESET
The RESET input on the MAX7503/MAX7504 provides a
way to reset the I2C bus and all the internal registers to
their initial POR values. To reset, apply a low pulse with
a duration of at least 1µs to the RESET input.
Digital Temperature Sensors and Thermal
Watchdog with Bus Lockup Protection
10 ______________________________________________________________________________________
MAX7504
+VS
A2/RESET
A1
A0
SDA
SCL OS
SMBus
INTERFACE
BLOCK
POINTER REGISTER
(SELECTS REGISTER
FOR COMMUNICATION)
DATA ADDRESS
REGISTER SELECT
GND
TEMPERATURE
(READ ONLY)
POINTER = 0000 0000
TOS SET POINT
(READ/WRITE)
POINTER = 0000 0011
THYST SET POINT
(READ/WRITE)
POINTER = 0000 0010
CONFIGURATION
(READ/WRITE)
POINTER = 0000 0001
Figure 5. Block Diagram
Applications Information
Digital Noise
The MAX7500–MAX7504 feature an integrated lowpass
filter on both the SCL and the SDA digital lines to miti-
gate the effects of bus noise. Although this filtering
makes communication robust in noisy environments,
good layout practices are always recommended.
Minimize noise coupling by keeping digital traces away
from switching power supplies. Ensure that digital lines
containing high-speed data communications cross at
right angles to the SDA and SCL lines.
Excessive noise coupling into the SDA and SCL lines
on the MAX7500–MAX7504—specifically noise with
amplitude greater than 400mVP-P (the MAX7500–
MAX7504s’ typical hysteresis), overshoot greater than
300mV above +VS, and undershoot more than 300mV
below GND—may prevent successful serial communi-
cation. Serial bus no-acknowledge is the most common
symptom, causing unnecessary traffic on the bus.
Care must be taken to ensure proper termination within
a system with long PC board traces or multiple parts on
the bus. Resistance can be added in series with the
SDA and SCL lines to further help filter noise and ring-
ing. If it proves to be necessary, a 5kΩresistor should
be placed in series with the SCL line, placed as close
as possible to SCL. This 5kΩresistor, with the 5pF to
10pF stray capacitance of the MAX7500–MAX7504 pro-
vide a 6MHz to 12MHz lowpass filter, which is sufficient
filtering in most cases.
Chip Information
TRANSISTOR COUNT: 9611
PROCESS: CMOS
MAX7500–MAX7504
Digital Temperature Sensors and Thermal
Watchdog with Bus Lockup Protection
______________________________________________________________________________________ 11
Ordering Information/
Selector Guide (continued)
PART TEMP
RANGE
PIN-
PACKAGE
RESET
TIMEOUT
MAX7501MSA
-55°C to
+125°C
8 SO X X
MAX7501MSA+
-55°C to
+125°C
8 SO X X
MAX7501MUA
-55°C to
+125°C
8 µMAX X X
MAX7501MUA+
-55°C to
+125°C
8 µMAX X X
MAX7502MSA
-55°C to
+125°C
8 SO X —
MAX7502MSA+
-55°C to
+125°C
8 SO X —
MAX7502MUA
-55°C to
+125°C
8 µMAX X —
MAX7502MUA+
-55°C to
+125°C
8 µMAX X —
MAX7503MSA
-55°C to
+125°C
8 SO X —
MAX7503MSA+
-55°C to
+125°C
8 SO X —
MAX7503MUA
-55°C to
+125°C
8 µMAX X —
MAX7503MUA+
-55°C to
+125°C
8 µMAX X —
MAX7504MSA
-55°C to
+125°C
8 SO X —
MAX7504MSA+
-55°C to
+125°C
8 SO X —
MAX7504MUA
-55°C to
+125°C
8 µMAX X —
MAX7504MUA+
-55°C to
+125°C
8 µMAX X —
+Denotes lead-free package.
MAX7500–MAX7504
Digital Temperature Sensors and Thermal
Watchdog with Bus Lockup Protection
12 ______________________________________________________________________________________
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
8LUMAXD.EPS
PACKAGE OUTLINE, 8L uMAX/uSOP
1
1
21-0036 J
REV.DOCUMENT CONTROL NO.APPROVAL
PROPRIETARY INFORMATION
TITLE:
MAX
0.043
0.006
0.014
0.120
0.120
0.198
0.026
0.007
0.037
0.0207 BSC
0.0256 BSC
A2 A1
c
eb
A
L
FRONT VIEW SIDE VIEW
E H
0.6±0.1
0.6±0.1
Ø0.50±0.1
1
TOP VIEW
D
8
A2 0.030
BOTTOM VIEW
16∞
S
b
L
H
E
D
e
c
0∞
0.010
0.116
0.116
0.188
0.016
0.005
8
4X S
INCHES
-
A1
A
MIN
0.002
0.950.75
0.5250 BSC
0.25 0.36
2.95 3.05
2.95 3.05
4.78
0.41
0.65 BSC
5.03
0.66
6∞0∞
0.13 0.18
MAX
MIN
MILLIMETERS
-1.10
0.05 0.15
α
α
DIM
MAX7500–MAX7504
Digital Temperature Sensors and Thermal
Watchdog with Bus Lockup Protection
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13
©2005 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc.
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
SOICN .EPS
PACKAGE OUTLINE, .150" SOIC
1
1
21-0041 B
REV.DOCUMENT CONTROL NO.APPROVAL
PROPRIETARY INFORMATION
TITLE:
TOP VIEW
FRONT VIEW
MAX
0.010
0.069
0.019
0.157
0.010
INCHES
0.150
0.007
E
C
DIM
0.014
0.004
B
A1
MIN
0.053A
0.19
3.80 4.00
0.25
MILLIMETERS
0.10
0.35
1.35
MIN
0.49
0.25
MAX
1.75
0.050
0.016L0.40 1.27
0.3940.386D
D
MINDIM
D
INCHES
MAX
9.80 10.00
MILLIMETERS
MIN MAX
16 AC
0.337 0.344 AB8.758.55 14
0.189 0.197 AA5.004.80 8
NMS012
N
SIDE VIEW
H0.2440.228 5.80 6.20
e0.050 BSC 1.27 BSC
C
HE
eBA1
A
D
0∞-8∞
L
1
VARIATIONS:
MAX7500
Part Number Table
ENGLISH • 简体中文 • 日本語 • 한국어
WHAT'S NEW PRODUCTS SOLUTIONS DESIGN APPNOTES SUPPORT BUY COMPANY MEMBERS
Notes:
1. See the MAX7500 QuickView Data Sheet for further information on this product family or download the
MAX7500 full data sheet (PDF, 676kB).
2. Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales.
3. Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within
one business day.
4. Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt. More: See full
data sheet or Part Naming Conventions.
5. * Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the product
uses.
Part Number Free
Sample
Buy
Direct Package: TYPE PINS SIZE
DRAWING CODE/VAR *
Temp RoHS/Lead-Free?
Materials Analysis
MAX7500MTA-T
Buy
-55°C to +125°C RoHS/Lead-Free: No
MAX7500MSA
Sample
Buy SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-2*
-55°C to +125°C RoHS/Lead-Free: No
Materials Analysis
MAX7500MSA-T
Buy SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-2*
-55°C to +125°C RoHS/Lead-Free: No
Materials Analysis
MAX7500MSA+
Sample
Buy SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+2*
-55°C to +125°C RoHS/Lead-Free: Yes
Materials Analysis
MAX7500MSA+T
Buy SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+2*
-55°C to +125°C RoHS/Lead-Free: Yes
Materials Analysis
MAX7500MUA
Sample
Buy uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
-55°C to +125°C RoHS/Lead-Free: No
Materials Analysis
Pa
g
e 1 of 2MAX7500 - Part Number Table - Maxim/Dallas
31-Jul-2007mhtml:file://C:\TEMP\MAXM\MAX7500MTA-T.mht
Didn't Find What You Need?
Use pkgcode/variation: U8-1*
MAX7500MUA-T
Buy uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8-1*
-55°C to +125°C RoHS/Lead-Free: No
Materials Analysis
MAX7500MUA+
Sample
Buy uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8+1*
-55°C to +125°C RoHS/Lead-Free: Yes
Materials Analysis
MAX7500MUA+T
Buy uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8+1*
-55°C to +125°C RoHS/Lead-Free: Yes
Materials Analysis
CONTACT US: SEND US AN EMAIL
Copyright © 2007 by Maxim Integrated Products, Dallas Semiconductor • Legal Notices • Privacy Policy
Pa
g
e 2 of 2MAX7500 - Part Number Table - Maxim/Dallas
31-Jul-2007mhtml:file://C:\TEMP\MAXM\MAX7500MTA-T.mht
MAX7501
Part Number Table
ENGLISH • 简体中文 • 日本語 • 한국어
WHAT'S NEW PRODUCTS SOLUTIONS DESIGN APPNOTES SUPPORT BUY COMPANY MEMBERS
Notes:
1. See the MAX7501 QuickView Data Sheet for further information on this product family or download the
MAX7501 full data sheet (PDF, 676kB).
2. Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales.
3. Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within
one business day.
4. Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt. More: See full
data sheet or Part Naming Conventions.
5. * Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the product
uses.
Part Number Free
Sample
Buy
Direct Package: TYPE PINS SIZE
DRAWING CODE/VAR *
Temp RoHS/Lead-Free?
Materials Analysis
MAX7501MTA-T
Buy
-55°C to +125°C RoHS/Lead-Free: No
MAX7501MSA
Sample
Buy SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-2*
-55°C to +125°C RoHS/Lead-Free: No
Materials Analysis
MAX7501MSA-T
Buy
-55°C to +125°C RoHS/Lead-Free: No
MAX7501MSA+
Sample
Buy SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+2*
-55°C to +125°C RoHS/Lead-Free: Yes
Materials Analysis
MAX7501MSA+T
Buy SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+2*
-55°C to +125°C RoHS/Lead-Free: Yes
Materials Analysis
MAX7501MUA
Sample
Buy uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
-55°C to +125°C RoHS/Lead-Free: No
Materials Analysis
Pa
g
e 1 of 2MAX7501 - Part Number Table - Maxim/Dallas
31-Jul-2007mhtml:file://C:\TEMP\MAXM\MAX7501MTA-T.mht
Didn't Find What You Need?
Use pkgcode/variation: U8-1*
MAX7501MUA-T
Buy
-55°C to +125°C RoHS/Lead-Free: No
MAX7501MUA+
Sample
Buy uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8+1*
-55°C to +125°C RoHS/Lead-Free: Yes
Materials Analysis
MAX7501MUA+T
Buy uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8+1*
-55°C to +125°C RoHS/Lead-Free: Yes
Materials Analysis
CONTACT US: SEND US AN EMAIL
Copyright © 2007 by Maxim Integrated Products, Dallas Semiconductor • Legal Notices • Privacy Policy
Pa
g
e 2 of 2MAX7501 - Part Number Table - Maxim/Dallas
31-Jul-2007mhtml:file://C:\TEMP\MAXM\MAX7501MTA-T.mht
MAX7502
Part Number Table
ENGLISH • 简体中文 • 日本語 • 한국어
WHAT'S NEW PRODUCTS SOLUTIONS DESIGN APPNOTES SUPPORT BUY COMPANY MEMBERS
Notes:
1. See the MAX7502 QuickView Data Sheet for further information on this product family or download the
MAX7502 full data sheet (PDF, 676kB).
2. Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales.
3. Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within
one business day.
4. Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt. More: See full
data sheet or Part Naming Conventions.
5. * Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the product
uses.
Part Number Free
Sample
Buy
Direct Package: TYPE PINS SIZE
DRAWING CODE/VAR *
Temp RoHS/Lead-Free?
Materials Analysis
MAX7502MTA-T
Buy
-55°C to +125°C RoHS/Lead-Free: No
MAX7502MSA
Sample
Buy SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-2*
-55°C to +125°C RoHS/Lead-Free: No
Materials Analysis
MAX7502MSA-T
Buy
-55°C to +125°C RoHS/Lead-Free: No
MAX7502MSA+
Sample
Buy SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+2*
-55°C to +125°C RoHS/Lead-Free: Yes
Materials Analysis
MAX7502MSA+T
Buy SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+2*
-55°C to +125°C RoHS/Lead-Free: Yes
Materials Analysis
MAX7502MUA
Sample
Buy uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
-55°C to +125°C RoHS/Lead-Free: No
Materials Analysis
Pa
g
e 1 of 2MAX7502 - Part Number Table - Maxim/Dallas
31-Jul-2007mhtml:file://C:\TEMP\MAXM\MAX7502MTA-T.mht
Didn't Find What You Need?
Use pkgcode/variation: U8-1*
MAX7502MUA-T
Buy
-55°C to +125°C RoHS/Lead-Free: No
MAX7502MUA+
Sample
Buy uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8+1*
-55°C to +125°C RoHS/Lead-Free: Yes
Materials Analysis
MAX7502MUA+T
Buy uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8+1*
-55°C to +125°C RoHS/Lead-Free: Yes
Materials Analysis
CONTACT US: SEND US AN EMAIL
Copyright © 2007 by Maxim Integrated Products, Dallas Semiconductor • Legal Notices • Privacy Policy
Pa
g
e 2 of 2MAX7502 - Part Number Table - Maxim/Dallas
31-Jul-2007mhtml:file://C:\TEMP\MAXM\MAX7502MTA-T.mht
MAX7503
Part Number Table
ENGLISH • 简体中文 • 日本語 • 한국어
WHAT'S NEW PRODUCTS SOLUTIONS DESIGN APPNOTES SUPPORT BUY COMPANY MEMBERS
Notes:
1. See the MAX7503 QuickView Data Sheet for further information on this product family or download the
MAX7503 full data sheet (PDF, 676kB).
2. Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales.
3. Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within
one business day.
4. Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt. More: See full
data sheet or Part Naming Conventions.
5. * Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the product
uses.
Part Number Free
Sample
Buy
Direct Package: TYPE PINS SIZE
DRAWING CODE/VAR *
Temp RoHS/Lead-Free?
Materials Analysis
MAX7503MSA
Buy SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-2*
-55°C to +125°C RoHS/Lead-Free: No
Materials Analysis
MAX7503MSA-T
Buy
-55°C to +125°C RoHS/Lead-Free: No
MAX7503MUA+
Sample
Buy uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8+1*
-55°C to +125°C RoHS/Lead-Free: Yes
Materials Analysis
MAX7503MUA+T
Buy uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8+1*
-55°C to +125°C RoHS/Lead-Free: Yes
Materials Analysis
MAX7503MUA
Buy uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8-1*
-55°C to +125°C RoHS/Lead-Free: No
Materials Analysis
MAX7503MUA-T
Buy
-55°C to +125°C RoHS/Lead-Free: No
Pa
g
e 1 of 2MAX7503 - Part Number Table - Maxim/Dallas
31-Jul-2007mhtml:file://C:\TEMP\MAXM\MAX7503MSA-T.mht
Didn't Find What You Need?
CONTACT US: SEND US AN EMAIL
Copyright © 2007 by Maxim Integrated Products, Dallas Semiconductor • Legal Notices • Privacy Policy
Pa
g
e 2 of 2MAX7503 - Part Number Table - Maxim/Dallas
31-Jul-2007mhtml:file://C:\TEMP\MAXM\MAX7503MSA-T.mht
MAX7504
Part Number Table
ENGLISH • 简体中文 • 日本語 • 한국어
WHAT'S NEW PRODUCTS SOLUTIONS DESIGN APPNOTES SUPPORT BUY COMPANY MEMBERS
Notes:
1. See the MAX7504 QuickView Data Sheet for further information on this product family or download the
MAX7504 full data sheet (PDF, 676kB).
2. Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales.
3. Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within
one business day.
4. Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt. More: See full
data sheet or Part Naming Conventions.
5. * Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the product
uses.
Part Number Free
Sample
Buy
Direct Package: TYPE PINS SIZE
DRAWING CODE/VAR *
Temp RoHS/Lead-Free?
Materials Analysis
MAX7504MSA
Buy SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-2*
-55°C to +125°C RoHS/Lead-Free: No
Materials Analysis
MAX7504MSA-T
Buy
-55°C to +125°C RoHS/Lead-Free: No
MAX7504MUA+
Sample
Buy
-55°C to +125°C RoHS/Lead-Free: Yes
MAX7504MUA+T
Buy
-55°C to +125°C RoHS/Lead-Free: Yes
MAX7504MUA
Buy uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8-1*
-55°C to +125°C RoHS/Lead-Free: No
Materials Analysis
MAX7504MUA-T
Buy
-55°C to +125°C RoHS/Lead-Free: No
Pa
g
e 1 of 2MAX7504 - Part Number Table - Maxim/Dallas
31-Jul-2007mhtml:file://C:\TEMP\MAXM\MAX7504MSA-T.mht
Didn't Find What You Need?
CONTACT US: SEND US AN EMAIL
Copyright © 2007 by Maxim Integrated Products, Dallas Semiconductor • Legal Notices • Privacy Policy
Pa
g
e 2 of 2MAX7504 - Part Number Table - Maxim/Dallas
31-Jul-2007mhtml:file://C:\TEMP\MAXM\MAX7504MSA-T.mht