Linear Li-Ion Battery Charger with Power Path and USB Compatibility in LFCSP ADP5062 Data Sheet FEATURES GENERAL DESCRIPTION 4 mm x 4 mm LFCSP package Fully programmable via I2C Flexible digital control inputs Up to 2.1 A current from an ac charger in LDO mode Operating input voltage from 4.0 V to 6.7 V Tolerant input voltage from -0.5 V to +20 V (USB VBUS) Fully compatible with USB 3.0 and USB Battery Charging Specification 1.2 Built-in current sensing and limiting As low as 54 m battery isolation FET between battery and charger output Thermal regulation prevents overheating Compliant with JEITA 1 and JEITA 2 Li-Ion battery charging temperature specifications SYS_EN flag permits the system to be disabled until battery is at the minimum required level for guaranteed system start-up The ADP5062 charger is fully compliant with USB 3.0 and the USB Battery Charging Specification 1.2 and enables charging via the mini USB VBUS pin from a wall charger, car charger, or USB host port. APPLICATIONS The ADP5062 has three factory-programmable digital input/output pins that provide maximum flexibility for different systems. These digital input/output pins permit combinations of features such as, input current limits, charging enable and disable, charging current limits, and a dedicated interrupt output pin. The ADP5062 operates from a 4 V to 6.7 V input voltage range but is tolerant of voltages up to 20 V thereby alleviating concerns about USB bus spikes during disconnect or connect scenarios. The ADP5062 features an internal FET between the linear charger output and the battery. This permits battery isolation and, hence, system powering under a dead battery or no battery scenario, which allows for immediate system function on connection to a USB power supply. Based on the type of USB source, which is detected by an external USB detection chip, the ADP5062 can be set to apply the correct current limit for optimal charging and USB compliance. Digital still cameras Digital video cameras Single cell Li-Ion portable equipment PDAs, audio, and GPS devices Portable medical devices Mobile phones TYPICAL APPLICATION CIRCUIT ADP5062 VBUS PROGRAMMABLE C4 10F ISO_Sx VIN CBP C1 10nF C3 22F SCL SDA DIG_IO1 DIG_IO2 DIG_IO3 SYSTEM ISO_Bx CHARGER CONTROL BLOCK BAT_SNS + Li-ion C2 22F THR SYS_EN ILED AGND VLED 10806-001 AC OR USB Figure 1. Rev. B Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2012-2013 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADP5062 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Battery Isolation FET ................................................................. 21 Applications ....................................................................................... 1 Battery Detection ....................................................................... 21 General Description ......................................................................... 1 Battery Pack Temperature Sensing .......................................... 22 Typical Application Circuit ............................................................. 1 I2C Interface ................................................................................ 26 Revision History ............................................................................... 2 I2C Register Map......................................................................... 27 Specifications..................................................................................... 3 Register Bit Descriptions ........................................................... 28 Recommended Input and Output Capacitances ...................... 6 Applications Information .............................................................. 36 I C-Compatible Interface Timing Specifications ..................... 6 External Components ................................................................ 36 Absolute Maximum Ratings ....................................................... 8 PCB Layout Guidelines.............................................................. 38 Thermal Resistance ...................................................................... 8 Power Dissipation and Thermal Considerations ....................... 39 ESD Caution .................................................................................. 8 Charger Power Dissipation ....................................................... 39 Pin Configuration and Function Descriptions ............................. 9 Junction Temperature ................................................................ 39 Typical Performance Characteristics ........................................... 10 Factory-Programmable Options .................................................. 40 Temperature Characteristics ..................................................... 12 Charger Options ......................................................................... 40 Typical Waveforms ..................................................................... 14 I2C Register Defaults .................................................................. 41 Theory of Operation ...................................................................... 15 Digital Input and Output Options ........................................... 41 Summary of Operation Modes ................................................. 15 Packaging and Ordering Information ......................................... 43 Introduction ................................................................................ 16 Outline Dimensions ................................................................... 43 Charger Modes............................................................................ 18 Ordering Guide .......................................................................... 43 2 Thermal Management ............................................................... 21 REVISION HISTORY 10/13--Rev. A to Rev. B Changes to Table 19 ........................................................................ 28 Changes to Table 26 ........................................................................ 32 Changes to Charger Options Section and Table 41 ................... 40 Changes to Ordering Guide .......................................................... 43 4/13--Rev. 0 to Rev. A Changes to Figure 3 .......................................................................... 9 9/12--Revision 0: Initial Version Rev. B | Page 2 of 44 Data Sheet ADP5062 SPECIFICATIONS -40C < TJ < +125C, VVINx = 5.0 V, RHOT_RISE < RTHR < RCOLD_FALL, VBAT_SNS = 3.6 V, VISO_Bx = VBAT_SNS, CVIN = 10 F, CISO_S = 22 F, CISO_B = 22 F, CCBP = 10 nF, all registers at default values, unless otherwise noted. Table 1. Parameter GENERAL PARAMETERS Undervoltage Lockout Hysteresis Total Input Current VINx Current Consumption Battery Current Consumption CHARGER Fast Charge Current CC Mode Symbol Min Typ Max Unit Test Conditions/Comments VUVLO 2.25 50 74 114 2.35 100 92 2.5 150 100 150 300 V mV mA mA mA 425 470 500 900 1500 5 mA mA mA mA A A A 0.5 0.9 mA Falling threshold, higher of VVINx and VBAT_SNS 1 Hysteresis, higher of VVINx and VBAT_SNS rising1 Nominal USB initialized current level 2 USB super speed USB enumerated current level (specification for China) USB enumerated current level Dedicated charger input Dedicated wall charger Charging or LDO mode DIS_IC1 = high, VISO_Bx < VINx < 5.5 V LDO mode, VISO_Sx > VBAT_SNS Standby, includes ISO_Sx pin leakage, VVINx = 0 V, TJ = -40C to +85C Standby, battery monitor active 750 790 mA +7 +29 +40 25 % mA mA mA mA ILIM IQVIN IQVIN_DIS IQBATT ICHG Fast Charge Current Accuracy Trickle Charge Current2 Weak Charge Current2, 3 Trickle to Weak Charge Threshold Dead Battery Hysteresis Weak Battery Threshold Weak to Fast Charge Threshold Battery Termination Voltage Termination Voltage Accuracy ITRK_DEAD ICHG_WEAK 2 280 20 700 -8 -33 -45 16 20 ITRK_DEAD + ICHG 450 VISO_Bx = 3.9 V; fast charge current accuracy is guaranteed at temperatures from TJ = -40C to the isothermal regulation limit (typically TJ = +115C)2, 3 ICHG = 400 mA to 1300 mA ICHG = 250 mA to 350 mA ICHG = 50 mA to 200 mA VTRK_DEAD VTRK_DEAD 2.4 2.5 100 2.6 V mV VTRK_DEAD < VBAT_SNS < VWEAK2, 4 On BAT_SNS2 VWEAK VWEAK VTRM 2.89 3.0 100 4.200 3.11 V mV V % % % V mA mA On BAT_SNS2, 4 -0.25 -1.04 -1.16 Battery Overvoltage Threshold Charge Complete Current Charging Complete Current Threshold Accuracy VBATOV IEND Recharge Voltage Differential Battery Node Short Threshold Voltage2 Battery Short Detection Current Charging Start Voltage Limit Charging Soft Start Current Charging Soft Start Timer VRCH VBAT_SHR ITRK_SHORT VCHG_VLIM ICHG_START tCHG_START 15 17 59 160 2.2 3.6 185 +0.25 +0.89 +1.20 VIN - 0.075 52.5 260 2.4 20 3.7 260 3 98 83 123 390 2.5 3.8 365 Rev. B | Page 3 of 44 mA mV V mA V mA ms On BAT_SNS, TJ = 25C, IEND = 52.5 mA2 TJ = 0C to 115C2 TJ = -40C to +125C Relative to VINx voltage, BAT_SNS rising VBAT_SNS = VTRM IEND = 52.5 mA, TJ = 0C to 115C2 IEND = 92.5 mA, TJ = 0C to 115C Relative to VTRM, BAT_SNS falling2 ITRK_SHORT = ITRK_DEAD2 Voltage limit is not active by default VBAT_SNS > VTRK_DEAD ADP5062 Parameter BATTERY ISOLATION FET Pin to Pin Resistance Between ISO_Sx and ISO_Bx Regulated System Voltage: VBAT Low Battery Supplementary Threshold LDO AND HIGH VOLTAGE BLOCKING Regulated System Voltage Load Regulation High Voltage Blocking FET (LDO FET) On Resistance Maximum Output Current VINx Input Voltage, Good Threshold Rising VINx Falling VINx Input Overvoltage Threshold Hysteresis VINx Transition Timing THERMAL CONTROL Isothermal Charging Temperature Thermal Early Warning Temperature Thermal Shutdown Temperature THERMISTOR CONTROL Thermistor Current 10,000 NTC 100,000 NTC Thermistor Capacitance Cold Temperature Threshold Resistance Thresholds Cool to Cold Resistance Cold to Cool Resistance Hot Temperature Threshold Resistance Thresholds Hot to Typical Resistance Typical to Hot Resistance JEITA1 Li-ION BATTERY CHARGING SPECIFICATION DEFAULTS 5 JEITA Cold Temperature Resistance Thresholds Cool to Cold Resistance Cold to Cool Resistance JEITA Cool Temperature Resistance Thresholds Typical to Cool Resistance Cool to Typical Resistance JEITA Warm Temperature Resistance Thresholds Warm to Typical Resistance Typical to Warm Resistance Data Sheet Symbol Min Typ Max Unit Test Conditions/Comments 54 89 m VTHISO 3.6 3.2 0 3.8 3.4 5 4.0 3.5 12 V V mV On battery supplement mode, VINx = 0 V, VISO_Bx = 4.2 V, IISO_Bx = 500 mA VTRM[5:0] programming 4.00 V VTRM[5:0] programming < 4.00 V VISO_Sx < VISO_Bx, VSYS rising VISO_STRK 4.214 4.3 4.386 V -0.56 330 485 %/A m 2.1 3.9 4.0 A V RDSON_ISO VISO_SFC RDS(ON)HV VVIN_OK_RISE VVIN_OK_FALL VVIN_OV VVIN_OV TVIN_RISE TVIN_FALL 3.75 6.7 115 130 140 110 INTC_10k INTC_100k CNTC TNTC_COLD RHOT_FALL RHOT_RISE 400 40 100 0 20,500 2750 TJEITA_COLD 25,600 24,400 60 3700 3350 30,720 3950 0 RCOLD_FALL RCOLD_RISE TJEITA_COOL 20,500 RTYP_FALL RTYP_RISE TJEITA_WARM 13,200 RWARM_FALL RWARM_RISE 3.7 7.2 10 10 TLIM TSDL TSD RCOLD_FALL RCOLD_RISE TNTC_HOT 3.6 6.9 0.1 4260 30,720 16,500 15,900 45 19,800 5800 5200 6140 Rev. B | Page 4 of 44 VISO_Sx = 4.3 V, LDO mode V V V s s Minimum rise time for VINx from 5 V to 20 V Minimum fall time for VINx from 4 V to 0 V C C C C TJ rising TJ falling A A pF C No battery charging occurs C No battery charging occurs C 25,600 24,400 10 VSYSTEM[2:0] = 000 (binary) = 4.3 V, IISO_Sx = 100 mA, LDO mode2 IISO_Sx = 0 m A to 1500 mA IVINx = 500 mA C C No battery charging occurs Battery charging occurs at 50% of programmed level Battery termination voltage (VTRM) is reduced by 100 mV Data Sheet Parameter JEITA Hot Temperature Resistance Thresholds Hot to Warm Resistance Warm to Hot Resistance JEITA2 Li-ION BATTERY CHARGING SPECIFICATION DEFAULTS5 JEITA Cold Temperature Resistance Thresholds Cool to Cold Resistance Cold to Cool Resistance JEITA Cool Temperature Resistance Thresholds Typical to Cool Resistance Cool to Typical Resistance JEITA Warm Temperature Resistance Thresholds Warm to Typical Resistance Typical to Warm Resistance JEITA Hot Temperature Resistance Thresholds Hot to Warm Resistance Warm to Hot Resistance BATTERY DETECTION Sink Current Source Current Battery Threshold Low High Battery Detection Timer TIMERS Clock Oscillator Frequency Start Charging Delay Trickle Charge Fast Charge Charge Complete Deglitch Watchdog2 Safety Battery Short2 ILED OUTPUT PINS Voltage Drop over ILED Maximum Operating Voltage over ILED SYS_EN OUTPUT PIN SYS_EN FET On Resistance ADP5062 Symbol TJEITA_HOT RHOT_FALL RHOT_RISE Min 2750 TJEITA_COLD 3700 3350 Max 3950 0 RCOLD_FALL RCOLD_RISE TJEITA_COOL 20,500 RTYP_FALL RTYP_RISE TJEITA_WARM 13,200 RWARM_FALL RWARM_RISE TJEITA_HOT Typ 60 4260 30,720 16,500 15,900 45 19,800 6140 C C C RHOT_FALL RHOT_RISE 2750 3700 3350 3950 ISINK ISOURCE 13 7 20 10 34 13 mA mA VBATL VBATH tBATOK 1.8 1.9 3.4 333 2.0 V V ms fCLK tSTART tTRK tCHG tEND tDG 2.7 3 1 60 600 7.5 31 3.3 MHz sec min min min ms tWD tSAFE tBAT_SHR 36 32 40 30 VILED VMAXILED 200 RON_SYS_EN 10 44 5.5 Rev. B | Page 5 of 44 Test Conditions/Comments No battery charging occurs C 25,600 24,400 10 5800 5200 60 Unit C No battery charging occurs Battery termination voltage (VTRM) is reduced by 100 mV Battery termination voltage (VTRM) is reduced by 100 mV No battery charging occurs VBAT_SNS = VTRM, ICHG < IEND Applies to VTRK_DEAD, VRCH, IEND, VWEAK, VVIN_OK_RISE, and VVIN_OK_FALL sec min sec mV V IILED = 20 mA ISYS_EN = 20 mA ADP5062 Parameter LOGIC INPUT PINS Maximum Voltage on Digital Inputs Maximum Logic Low Input Voltage Minimum Logic High Input Voltage Pull-Down Resistance Data Sheet Symbol VDIN_MAX VIL VIH Min 1.2 215 Typ 350 Max Unit Test Conditions/Comments 5.5 0.5 V V V k Applies to SCL, SDA, DIG_IO1, DIG_IO2, DIG_IO3 Applies to SCL, SDA, DIG_IO1, DIG_IO2, DIG_IO3 Applies to SCL, SDA, DIG_IO1, DIG_IO2, DIG_IO3 Applies to DIG_IO1, DIG_IO2, DIG_IO3 610 Undervoltage lockout generated normally from ISO_Sx or ISO_Bx; in certain transition cases, it can be generated from VINx. These values are programmable via I2C. Values are given with default register values. The output current during charging may be limited by the input current limit or by the isothermal charging mode. 4 During weak charging mode, the charger provides at least 20 mA of charging current via the trickle charge branch to the battery unless trickle charging is disabled. Any residual current that is not required by the system is also used to charge the battery. 5 Either JEITA1 (default) or JEITA2 can be selected in I2C, or both JEITA functions can be enabled or disabled in I2C. 1 2 3 RECOMMENDED INPUT AND OUTPUT CAPACITANCES Table 2. Parameter CAPACITANCES VINx CBP ISO_Sx ISO_Bx Symbol Min Typ CVINx CCBP CISO_Sx CISO_Bx 4 6 10 10 10 22 22 Max Unit Test Conditions/Comments 10 14 100 F nF F F Effective capacitance Effective capacitance Effective capacitance Effective capacitance I2C-COMPATIBLE INTERFACE TIMING SPECIFICATIONS Table 3. Parameter 1 I2C-COMPATIBLE INTERFACE 2 Capacitive Load for Each Bus Line SCL Clock Frequency SCL High Time SCL Low Time Data Setup Time Data Hold Time Setup Time for Repeated Start Hold Time for Start/Repeated Start Bus Free Time Between a Stop and a Start Condition Setup Time for Stop Condition Rise Time of SCL/SDA Fall Time of SCL/SDA Pulse Width of Suppressed Spike 1 2 Symbol CS fSCL tHIGH tLOW tSU, DAT tHD, DAT tSU, STA tHD, STA tBUF tSU, STO tR tF tSP Min 0.6 1.3 100 0 0.6 0.6 1.3 0.6 20 20 0 Typ Max Unit 400 400 pF kHz s s ns s s s s s ns ns ns 0.9 300 300 50 Guaranteed by design. A master device must provide a hold time of at least 300 ns for the SDA signal to bridge the undefined region of the falling edge of SCL (see Figure 2). Rev. B | Page 6 of 44 Data Sheet ADP5062 Timing Diagram SDA tLOW tF tR tSU, DAT tSP tF tBUF tR tHD, STA SCL tHIGH tHD, DAT tSU, STO tSU, STA Sr P S 10806-002 S S = START CONDITION Sr = REPEATED START CONDITION P = STOP CONDITION Figure 2. I2C Timing Diagram Rev. B | Page 7 of 44 ADP5062 Data Sheet ABSOLUTE MAXIMUM RATINGS Maximum Power Dissipation Table 4. Absolute Maximum Ratings Parameter VIN1, VIN2, VIN3 to AGND All Other Pins to AGND Continuous Drain Current, Battery Supplementary Mode, from ISO_Bx to ISO_Sx Storage Temperature Range Operating Junction Temperature Range Soldering Conditions Rating -0.5 V to +20 V -0.3 V to +6 V 2.1 A -65C to +150C -40C to +125C JEDEC J-STD-020 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The maximum safe power dissipation in the ADP5062 package is limited by the associated rise in junction temperature (TJ) on the die. At a die temperature of approximately 150C (the glass transition temperature), the properties of the plastic change. Even temporarily exceeding this temperature limit may change the stresses that the package exerts on the die, thereby permanently shifting the parametric performance of the ADP5062. Exceeding a junction temperature of 175C for an extended period can result in changes in the silicon devices, potentially causing failure. ESD CAUTION THERMAL RESISTANCE JA is specified for the worst-case conditions, that is, JA is specified for a device soldered in a circuit board for surfacemount packages. Table 5. Thermal Resistance Package Type 20-Lead LFCSP JA 35.6 JC 3.65 Unit C/W Rev. B | Page 8 of 44 Data Sheet ADP5062 20 19 18 17 16 AGND CBP THR SDA SYS_EN PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 1 2 3 4 5 PIN 1 INDICATOR ADP5062 TOP VIEW (Not to Scale) 15 ILED 14 ISO_B3 13 ISO_B2 12 ISO_B1 11 ISO_S3 NOTES 1. CONNECTION OF THE EXPOSED PAD IS NOT REQUIRED. THE EXPOSED PAD CAN BE CONNECTED TO ANALOG GROUND TO IMPROVE HEAT DISSIPATION FROM THE PACKAGE TO BOARD. 10806-003 VIN1 VIN2 VIN3 ISO_S1 ISO_S2 6 7 8 9 10 SCL DIG_IO3 DIG_IO2 BAT_SNS DIG_IO1 Figure 3. Pin Configuration Table 6. Pin Function Descriptions Pin No. 9, 10, 11 Type 1 I/O 1 17 5 Name ISO_S1, ISO_S2, ISO_S3 VIN1, VIN2, VIN3 AGND ISO_B1, ISO_B2, ISO_B3 SCL SDA DIG_IO1 3 DIG_IO2 GPIO 2 DIG_IO3 GPIO 18 THR I 4 15 16 BAT_SNS ILED SYS_EN I O O 19 N/A 4 CBP EP I/O N/A4 6, 7, 8 20 12, 13, 14 I/O G I/O I I/O GPIO Description Linear Charger Supply Side Input to Internal Isolation FET/Battery Current Regulation FET. High current input/output. Power Connections to USB VBUS. These pins are high current inputs when in charging mode. Analog Ground. Battery Supply Side Input to Internal Isolation FET/Battery Current Regulation FET. I2C-Compatible Interface Serial Clock. I2C-Compatible Interface Serial Data. Set Input Current Limit. This pin sets the input current limit directly. When DIG_IO1 = low or high-Z, the input limit is 100 mA. When DIG_IO1 = high, the input limit is 500 mA. 2, 3 Disable IC1. The DIG_IO2 pin sets the charger to the low current mode. When DIG_IO2 = low or high-Z, the charger operates in normal mode. When DIG_IO2 = high, the LDO and the charger are disabled and VINx current consumption is 280 A (typical). In addition, when DIG_IO2 is high, 20 V VINx input protection is disabled and the VINx voltage level must fulfill the condition, VISO_Bx < VVINx < 5.5 V.2, 3 Enable Charging. When DIG_IO3 = low or high-Z, charging is disabled. When DIG_IO3 = high, charging is enabled.2, 3 Battery Pack Thermistor Connection. If this pin is not used, connect a dummy 10 k resistor from THR to GND. Battery Voltage Sense Pin. Open-Drain Output to Indicator LED. System Enable. This pin is the battery OK flag/open-drain pull-down FET to enable the system when the battery reaches the VWEAK level. Bypass Capacitor Input. Exposed Pad. Connection of the exposed pad is not required. The exposed pad can be connected to analog ground to improve heat dissipation from the package to the board. I is input, O is output, I/O is input/output, G is ground, and GPIO is the factory programmable general-purpose input/output. See the Digital Input and Output Options section for details. 3 The DIG_IOx setting defines the initial state of the ADP5062. If the parameter or the mode that is related to each DIG_IOx pin setting is changed (by programming an equivalent I2C register bit or bits), the I2C register setting takes precedence over the DIG_IOx pin setting. VINx connection or disconnection resets control to the DIG_IOx pin. 4 N/A means not applicable. 1 2 Rev. B | Page 9 of 44 ADP5062 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS 5.10 4.38 5.08 4.36 5.06 4.34 4.32 4.30 4.28 4.26 5.02 5.00 4.98 4.96 4.24 4.94 4.22 4.92 4.20 0.01 0.1 1 SYSTEM OUTPUT CURRENT (A) 4.4 5.2 LOAD = 100mA LOAD = 500mA LOAD = 1000mA 5.0 SYSTEM VOLTAGE (V) 4.2 4.1 4.0 3.9 3.8 4.8 4.6 4.4 4.2 4.0 3.7 3.8 3.6 3.6 5.2 4.8 5.6 6.0 6.4 3.4 4.0 10806-005 4.4 6.8 INPUT VOLTAGE (V) 4.4 4.8 5.2 5.6 6.0 6.4 6.8 INPUT VOLTAGE (V) Figure 5. System Voltage vs. Input Voltage (in Dropout), LDO Mode, VSYSTEM[2:0] = 000 (Binary) = 4.3 V Figure 8. System Voltage vs. Input Voltage (in Dropout), LDO Mode, VSYSTEM[2:0] = 111 (Binary) = 5.0 V 1000 700 900 600 700 CHARGE CURRENT (mA) 800 LIMIT = 900mA LIMIT = 500mA LIMIT = 100mA 600 500 400 300 WEAK CHARGE 500 FAST CHARGE 400 300 200 200 TRICKLE CHARGE 100 0 2.7 3.2 3.7 4.2 BATTERY VOLTAGE (V) Figure 6. Input Current-Limited Charge Current vs. Battery Voltage 0 2.3 2.8 3.3 BATTERY VOLTAGE (V) 3.8 4.3 10806-009 100 10806-006 CHARGE CURRENT (mA) 1 5.4 LOAD = 100mA LOAD = 500mA LOAD = 1000mA 4.3 3.5 4.0 0.1 SYSTEM OUTPUT CURRENT (A) 10806-008 4.5 4.90 0.01 Figure 7. System Voltage vs. System Output Current, LDO Mode, VVINx = 6.0 V, VSYSTEM[2:0] = 111 (Binary) = 5.0 V Figure 4. System Voltage vs. System Output Current, LDO Mode, VSYSTEM[2:0] = 000 (Binary) = 4.3 V SYSTEM VOLTAGE (V) 5.04 10806-007 SYSTEM VOLTAGE (V) 4.40 10806-004 SYSTEM VOLTAGE (V) VVINx = 5.0 V, CVINx = 10 F, CISO_Sx = 44 F, CISO_Bx = 22 F, CCBP = 10 nF, all registers at default values, unless otherwise noted. Figure 9. Battery Charge Current vs. Battery Voltage, ICHG[4:0] = 01001 (Binary) = 500 mA, ILIM[3:0] = 1111 (Binary) = 2100 mA Rev. B | Page 10 of 44 Data Sheet ADP5062 65 60 55 50 45 3.7 4.2 BATTERY VOLTAGE (V) 55 50 45 40 0 4.4 BATTERY VOLTAGE (A) 2.5 2.0 1.5 1.0 0.5 0 0 2 4 6 VINx VOLTAGE (V) Figure 11. VINx Current vs. VINx Voltage, No Battery 8 10806-011 VINx CURRENT (mA) 3.0 1.5 2.0 Figure 12. Ideal Diode RON vs. Load Current, VISO_Bx = 3.6 V DEFAULT STARTUP DIS_LDO = HIGH DIS_IC1 = HIGH 3.5 1.0 LOAD CURRENT (A) Figure 10. Ideal Diode RON vs. Battery Voltage, IISO_Sx = 500 mA, VINx Open 4.0 0.5 0.7 VBAT_SNS IISO_Bx 4.2 0.6 4.0 0.5 3.8 0.4 3.6 0.3 3.4 0.2 3.2 0.1 3.0 CHARGE CURRENT (A) 3.2 60 0 0 50 100 150 CHARGE TIME (min) Figure 13. Charge Profile, ILIM[3:0] = 0110 (Binary) = 500 mA, Battery Capacity = 925 mAh Rev. B | Page 11 of 44 10806-013 40 2.7 65 10806-012 ISOLATION FET RESISTANCE (m) 70 10806-010 ISOLATION FET RESISTANCE (m) 70 ADP5062 Data Sheet TEMPERATURE CHARACTERISTICS 1.5 0.5 VISO_Bx = 3.6V VISO_Bx = 4.2V VISO_Bx = 5.5V 1.3 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.2 0.1 0 -0.1 -0.2 -0.3 -15 10 35 60 85 AMBIENT TEMPERATURE (C) -0.5 -40 10806-014 0 -40 5 20 35 50 65 80 95 110 125 Figure 17. System Voltage vs. Temperature, Trickle Charge Mode, VISO_Sx = 4.3 V and VINx = 5.0 V, or VISO_Sx = 5.0 V and VINx = 6.0 V 5.0 VIN = 4.0V VIN = 5.0V VIN = 5.5V VIN = 4.0V VIN = 5.0V VIN = 6.7V 4.5 VINx QUIESCENT CURRENT (mA) 0.45 -10 AMBIENT TEMPERATURE (C) Figure 14. Battery Leakage Current vs. Ambient Temperature 0.50 -25 10806-017 -0.4 0.1 0.40 0.35 0.30 0.25 0.20 0.15 0.10 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.05 -25 -10 5 20 35 50 65 80 95 110 125 AMBIENT TEMPERATURE (C) 0 -40 10806-015 0 -40 Figure 15. VINx Quiescent Current vs. Ambient Temperature, DIS_IC1 = High 0.5 VTRM VOLTAGE ACCURACY (%) 0.1 0 -0.1 -0.2 -0.3 20 35 50 65 80 95 110 125 VTRM = 3.8V VTRM = 4.2V VTRM = 4.5V 0.4 0.2 5 Figure 18. VINx Quiescent Current vs. Ambient Temperature, LDO Mode VISO_Sx = 4.3V VISO_Sx = 5.0V 0.3 -10 AMBIENT TEMPERATURE (C) 0.5 0.4 -25 10806-018 VINx QUIESCENT CURRENT (mA) 0.3 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 -0.5 -40 -25 -10 5 20 35 50 65 80 95 110 AMBIENT TEMPERATURE (C) 125 10806-016 -0.4 -0.5 -40 -25 -10 5 20 35 50 65 80 95 110 125 AMBIENT TEMPERATURE (C) Figure 19. Termination Voltage vs. Ambient Temperature Figure 16. LDO Mode Voltage vs. Ambient Temperature, Load = 100 mA, VVINx = 5.5 V Rev. B | Page 12 of 44 10806-019 STANDBY CURRENT (A) 1.2 SYSTEM VOLTAGE ACCURACY (%) VISO_Sx = 4.3V VISO_Sx = 5.0V 0.4 SYSTEM VOLTAGE ACCURACY (%) 1.4 ADP5062 1.4 1.3 ICHG = 1300mA INPUT CURRENT LIMIT (A) CHARGE CURRENT (A) 1.2 1.1 1.0 0.9 0.8 0.7 ICHG = 750mA 0.6 ICHG = 500mA 0.4 -40 -15 10 35 60 85 110 AMBIENT TEMPERATURE (C) 10806-020 0.5 6.95 6.90 6.85 -10 5 20 35 50 65 80 95 110 125 AMBIENT TEMPERATURE (C) 10806-021 VIN OVERVOLTAGE THRESHOLD (V) 7.00 -25 20 35 50 65 80 95 110 AMBIENT TEMPERATURE (C) Figure 22. Input Current Limit vs. Ambient Temperature Figure 20. Fast Charge CC Mode Current vs. Ambient Temperature 6.80 -40 1.6 1.5 ILIM = 1500mA 1.4 1.3 1.2 1.1 1.0 0.9 ILIM = 900mA 0.8 0.7 0.6 0.5 ILIM = 500mA 0.4 0.3 0.2 ILIM = 100mA 0.1 0 -40 -25 -10 5 Figure 21. VINx Overvoltage Threshold vs. Ambient Temperature Rev. B | Page 13 of 44 125 10806-022 Data Sheet ADP5062 Data Sheet TYPICAL WAVEFORMS T T VISO_Sx VISO_Sx VVINx VVINx 4 4 1 1 IISO_Bx 2 2 IVINx IISO_Bx IVINx 120mA CH1 2.00V CH2 200mA CH3 200mA CH4 2.00V M200.0s T 0.00s A CH2 216mA 10806-026 M1.00ms A CH2 T 1.00ms 10806-023 CH1 2.00V CH2 200mA CH3 200mA CH4 2.00V -610mA 10806-027 3 3 Figure 26. USB VBUS Disconnect Figure 23. Charging Startup, VVINx = 5.0 V, ILIM[3:0] = 0110 (Binary) = 500 mA, ICHG[4:0] = 01110 (Binary) = 750 mA VISO_Sx T T VISO_Sx 1 3 1 IISO_Bx 2 IISO_Sx IISO_Sx CH1 100mV CH2 500mA M1.00ms A CH2 T 3.00ms 820mA 10806-024 2 CH1 1.00V CH2 500mA CH3 500mA M1.0ms A CH2 T 3.00ms Figure 24. Load Transient, IISO_Sx Load = 300 mA to 1500 mA to 300 mA Figure 27. Load Transient, IISO_Sx Load = 300 mA to 1500 mA to 300 mA, EN_CHG = High, ILIM[3:0] = 0110 (Binary) = 500 mA T T VISO_Sx 2 VVINx 1 VISO_Bx 2 IISO_Bx IISO_Bx 3 3 IVINx M40.0s T 0.00s A CH3 610mA Figure 25. Input Current-Limit Transition from 100 mA to 900 mA, ISO_Sx Load = 66 , Charging = 750 mA CH2 2.00V CH3 10.0mA M200ms T 0.00s A CH3 17.2mA 10806-028 CH1 200mV CH2 200mV CH3 500mA CH4 500mA 10806-025 4 Figure 28. Battery Detection Waveform, VSYSTEM[2:0] = 000 (Binary) = 4.3 V, No Battery Rev. B | Page 14 of 44 Data Sheet ADP5062 THEORY OF OPERATION SUMMARY OF OPERATION MODES Table 7. Summary of the ADP5062 Operation Modes Mode Name IC Off, Standby IC Off, Suspend LDO Mode Off, Isolation FET On LDO Mode Off, Isolation FET Off (System Off) LDO Mode, Charger Off Trickle Charge Mode Weak Charge Mode Fast Charge Mode Charge Mode, No Battery Charge Mode, Battery (ISO_Bx) Shorted 1 VINx Condition 0V Battery Condition Any battery condition Trickle Charge Off LDO FET State Off Battery Isolation FET On/Off 5V 5V Any battery condition Any battery condition Off Off Off Off On On System Voltage ISO_Sx Battery voltage or 0 V Battery voltage Battery voltage 5V Any battery condition Off Off Off 0V Disable IC1 Disable LDO and enable isolation FET Enable battery charging 5V 5V 5V 5V 5V 5V Any battery condition Battery < VTRK_DEAD VTRK_DEAD battery < VWEAK Battery VWEAK Open Shorted Off On On Off Off On LDO LDO CHG CHG LDO LDO Off Off CHG CHG Off Off 5.0 V 5.0 V 3.8 V 3.8 V (minimum) 5.0 V 5.0 V Enable battery charging Enable battery charging Enable battery charging Enable battery charging Enable battery charging Enable battery charging Additional Conditions 1 Disable IC1 See Table 8 for details. Table 8. Operation Mode Controls Pin Configuration Enable Battery Charging DIG_IOx DIG_IO3 Equivalent I2C Address, Data Bit(s) 0x07, D0 Disable IC1 DIG_IO2 0x07, D6 Disable LDO and Enable Isolation FET 1 2 0x07, D3, D0 Description Low = all charging modes disabled (fast, weak, trickle). High = all charging modes enabled (fast, weak, trickle). VINx 1 Supply Disable IC1 Connected LDO_FET ISO_FET Low No Off On Yes CHG CHG High No 2 Off On Yes Off On Low = LDO enabled. High = LDO disabled. In addition, when EN_CHG = low, the battery isolation FET is on; when EN_CHG = high, the battery isolation FET is off. When disable IC1 mode is active, the VINx supply must always be connected and the supply voltage level must fulfill the following condition: VISO_Bx < VINx < 5.5 V. When disable IC1 mode is active, the back gate of the LDO FET is not controlled. If the VINx pins are not connected to any voltage supply, the body diode of the LDO FET can become forward biased and the voltage at VINx is VISO_Bx - VF (VF is the forward voltage of the LDO FET body diode). Rev. B | Page 15 of 44 ADP5062 Data Sheet INTRODUCTION The ADP5062 is a fully-programmable I2C charger for single cell lithium-ion or lithium-polymer batteries suitable for a wide range of portable applications. The linear charger architecture enables up to 2.1 A output current at 4.3 V to 5.0 V (I2C programmable) on the system power supply, and up to 1.3 A charge current into the battery from a dedicated charger. The ADP5062 operates from an input voltage of 4 V up to 6.7 V but is tolerant of voltages of up to 20 V. The 20 V voltage tolerance alleviates the concerns of the USB bus spiking during disconnection or connection scenarios. The ADP5062 features an internal FET between the linear charger output and the battery. This feature permits battery isolation and, hence, system powering under a dead battery or no battery scenario, which allows for immediate system function upon connection to a USB power supply. The ADP5062 is fully compliant with USB 3.0 and the USB Battery Charging Specification 1.2. The ADP5062 is chargeable via the mini USB VBUS pin from a wall charger, car charger, or USB host port. Based on the type of USB source, which is detected by an external USB detection device, the ADP5062 can be set to apply the correct current limit for optimal charging and USB compliance. The USB charger permits correct operation under all USB compliant sources such as wall chargers, host chargers, hub chargers, and standard host and hubs. A processor can control the USB charger using the I2C to program the charging current and numerous other parameters, including * * * * * * * * * * * * Rev. B | Page 16 of 44 Trickle charge current level Trickle charge voltage threshold Weak charge (constant current) current level Fast charge (constant current) current level Fast charge (constant voltage) voltage level at 1% accuracy Fast charge safety timer period Watchdog safety timer parameters Weak battery threshold detection Charge complete threshold Recharge threshold Charge enable/disable Battery pack temperature detection and automatic charger shutdown Data Sheet 6 TO USB VBUS OR WALL ADAPTER 7 8 ADP5062 VIN1 ISO_S1 HIGH VOLTAGE BLOCKING LDO FET ISO_S2 VIN2 VIN3 ISO_S3 + 6.85V + LDO FET CONTROL - VIN LIMIT 9 TO SYSTEM LOAD 10 11 - VIN OVERVOLTAGE CBP BATTERY ISOLATION FET 19 TRICKLE CURRENT SOURCE + 3.9V - 3MHz OSC ISO_B1 + VIN GOOD - 1 17 3 2 ISO_B2 13 SCL CHARGE CONTROL DIG_IO1 DIG_IO2 ISO_B3 + SDA - 5 EOC 12 I2C INTERFACE AND CONTROL LOGIC 14 CV MODE RECHARGE + - DIG_IO3 WEAK BATTERY DETECTION SINK + - BATTERY: OPEN SHORT TRICKLE BAT_SNS + 4 3.4V - 1.9V BATTERY DETECTION - SYS_EN + 16 SYS_EN OUTPUT LOGIC + - VIN - 150mV BATTERY OVERVOLTAGE TSD 140C WARNING 130C ISOTHERMAL 115C TSD DOWN 110C WARM NTC CURRENT CONTROL HOT THR THERMAL CONTROL AGND 0.5V 18 NTC 20 SINGLE CELL Li-Ion Figure 29. Block Diagram Rev. B | Page 17 of 44 10806-029 ILED OUTPUT LOGIC COLD COOL - ILED + 15 ADP5062 Data Sheet Table 9. DIG_IO1 Operation The ADP5062 includes a number of significant features to optimize charging and functionality including * * * * Thermal regulation for maximum performance. USB host current limit. Termination voltage accuracy: 1%. Battery thermistor input with automatic charger shutdown in the event that the battery temperature exceeds limits (compliant with the JEITA Li-Ion battery charging temperature specification). * Three external pins (DIG_IO1, DIG_IO2, and DIG_IO3) that directly control a number of parameters. These pins are factory programmable for maximum flexibility. They can be factory programmed for functions such as * Enable/disable charging. * Control of 100 mA or 500 mA input current limit. * Control of 1500 mA input current limit. * Control of the battery charge current. * Interrupt output pin. See the Digital Input and Output Options section for details. CHARGER MODES Input Current Limit The VINx input current limit is controlled via the internal I2C ILIM bits. The input current limit can also be controlled via the DIG_IO1 pin (if factory programmed to do so) as outlined in Table 9. Any change in the I2C default from 100 mA takes precedence over the pin setting. DIG_IO1 0 1 Function 100 mA input current limit or I2C programmed value 500 mA input current limit or I2C programmed value (or reprogrammed I2C value from 100 mA default) USB Compatibility The ADP5062 features an I2C-programmable input current limit to ensure compatibility with the requirements listed in Table 10. The current limit defaults to 100 mA to allow compatibility with a USB host or hub that is not configured. The I2C register default is 100 mA. An I2C write command to the ILIM register overrides the DIG_IOx pins and the I2C register default value can be reprogrammed for alternative requirements. When the input current-limit feature is used, the available input current may be too low for the charger to meet the programmed charging current, ICHG, thereby reducing the rate of charge and setting the VIN_ILIM flag. When connecting voltage to VINx without the proper voltage level on the battery side, the high voltage blocking mechanism is in a state wherein it draws only the current of <1 mA until VIN reaches the VIN_OK level. The ADP5062 charger provides support for the following connections through the single connector VINx pin, as shown in Table 10. Table 10. Input Current Compatibility with Standard USB Limits Mode USB (China Only) USB 2.0 USB 3.0 Dedicated Charger Standard USB Limit 100 mA limit for standard USB host or hub 300 mA limit for Chinese USB specification 100 mA limit for standard USB host or hub 500 mA limit for standard USB host or hub 150 mA limit for superspeed USB 3.0 host or hub 900 mA limit for superspeed, high speed USB host or hub charger 1500 mA limit for dedicated charger or low/full speed USB host or hub charger Rev. B | Page 18 of 44 ADP5062 Function 100 mA input current limit or I2C programmed value 300 mA input current limit or I2C programmed value 100 mA input current limit or I2C programmed value 500 mA input current limit or I2C programmed value 150 mA input current limit or I2C programmed value 900 mA input current limit or I2C programmed value 1500 mA input current limit or I2C programmed value Data Sheet ADP5062 Trickle Charge Mode Fast Charge Mode (Constant Current) A deeply discharged Li-Ion cell can exhibit a very low cell voltage making it unsafe to charge the cell at high current rates. The ADP5062 charger uses a trickle charge mode to reset the battery pack protection circuit and lift the cell voltage to a safe level for fast charging. A cell with a voltage below VTRK_DEAD is charged with the trickle mode current, ITRK_DEAD. During trickle charging mode, the CHARGER_STATUS bits are set. When the battery voltage exceeds VTRK_DEAD and VWEAK, the charger switches to fast charge mode, charging the battery with the constant current, ICHG. During fast charge mode (constant current), the CHARGER_STATUS bits are set to 010. During trickle charging, the ISO_Sx node is regulated to VISO_STRK by the LDO and the battery isolation FET is off, which means that the battery is isolated from the system power supply. During constant current mode, other features may prevent the current, ICHG, from reaching its full programmed value. Isothermal charging mode or input current limiting for USB compatibility can affect the value of ICHG under certain operating conditions. The voltage on ISO_Sx is regulated to stay at VISO_SFC by the battery isolation FET when VISO_Bx < VISO_SFC. Trickle Charge Mode Timer Fast Charge Mode (Constant Voltage) The duration of trickle charge mode is monitored to ensure that the battery is revived from its deeply discharged state. If trickle charge mode runs for longer than 60 minutes without the cell voltage reaching VTRK_DEAD, a fault condition is assumed and charging stops. The fault condition is asserted on the CHARGER_ STATUS bits, allowing the user to initiate the fault recovery procedure specified in the Fault Recovery section. As the battery charges, its voltage rises and approaches the termination voltage, VTRM. The ADP5062 charger monitors the voltage on the BAT_SNS pin to determine when charging should end. However, the internal ESR of the battery pack combined with the printed circuit board (PCB) and other parasitic series resistances creates a voltage drop between the sense point at the BAT_SNS pin and the cell terminal. To compensate for this and to ensure a fully charged cell, the ADP5062 enters a constant voltage charging mode when the termination voltage is detected on the BAT_SNS pin. The ADP5062 reduces charge current gradually as the cell continues to charge, maintaining a voltage of VTRM on the BAT_SNS pin. During fast charge mode (constant voltage), the CHARGER_ STATUS[2:0] bits are set to 011. Weak Charge Mode (Constant Current) When the battery voltage exceeds VTRK_DEAD but is less than VWEAK, the charger switches to intermediate charge mode. During the weak charge mode, the battery voltage is too low to allow the full system to power-up. Because of the low battery level, the USB transceiver cannot be powered and, therefore, cannot enumerate for more current from a USB host. Consequently, the USB limit remains at 100 mA. The system microcontroller may or may not be powered by the charger output voltage (VISO_SFC), depending upon the amount of current that the microcontroller and/or the system architecture requires. When the ISO_Sx pins power the microcontroller, the battery charge current (ICHG_WEAK) cannot be increased above 20 mA to ensure microcontroller operation (if doing so), nor can ICHG_WEAK be increased above the 100 mA USB limit. Therefore, set the battery charging current as follows: * * Set the default 20 mA via the linear trickle charger branch (to ensure that the microprocessor remains alive if powered by the main charger output, ISO_Sx). Any residual current on the main charger output, ISO_Sx, is used to charge the battery. During weak current mode, other features may prevent the weak charging current from reaching its full programmed value. Isothermal charging mode or input current limiting for USB compatibility can affect the programmed weak charging current value under certain operating conditions. During weak charging, the ISO_Sx node is regulated to VISO_SFC by the battery isolation FET. Fast Charge Mode Timer The duration of fast charge mode is monitored to ensure that the battery is charging correctly. If the fast charge mode runs for longer than tCHG without the voltage at the BAT_SNS pin reaching VTRM, a fault condition is assumed and charging stops. The fault condition is asserted on the CHARGER_STATUS[2:0] bits, allowing the user to initiate the fault recovery procedure as specified in the Fault Recovery section. If the fast charge mode runs for longer than tCHG, and VTRM has been reached on the BAT_SNS pin but the charge current has not yet fallen below IEND, charging stops. No fault condition is asserted in this circumstance and charging resumes as normal if the recharge threshold is breached. Watchdog Timer The ADP5062 charger features a programmable watchdog timer function to ensure charging is under the control of the processor. The watchdog timer starts running when the ADP5062 charger determines that the processor should be operational, that is, when the processor sets the RESET_WD bit for the first time or when the battery voltage is greater than the weak battery threshold, VWEAK. When the watchdog timer has been triggered, it must be reset regularly within the watchdog timer period, tWD. While in charger mode, if the watchdog timer expires without being reset, the ADP5062 charger assumes that there is a software problem and triggers the safety timer, tSAFE. For more information see the Safety Timer section. Rev. B | Page 19 of 44 ADP5062 Data Sheet Safety Timer Battery Voltage Limit to Prevent Charging While in charger mode, if the watchdog timer expires, the ADP5062 charger initiates the safety timer, tSAFE (see the Watchdog Timer section). If the processor has programmed charging parameters by the time the charger initiates the safety timer, the ILIM is set to the default value. Charging continues for a period of tSAFE, and then the charger switches off and sets the CHARGER_STATUS [2:0] bits. The battery monitor of the ADP5062 charger can be configured to monitor battery voltage and prevent charging when the battery voltage is higher than VCHG_VLIM (typically 3.7 V) during charging start-up (enabled by EN_CHG or DIG_IO3). This function can prevent unnecessary charging of a half discharged battery and, as such, can extend the lifetime of the Li-Ion battery cell. Charging starts automatically when the battery voltage drops below VCHG_VLIM and continues through full charge cycle until the battery voltage reaches VTRM (typically 4.2 V). Charge Complete The ADP5062 charger monitors the charging current while in constant voltage fast charge mode. If the current falls below IEND and remains below IEND for tEND, charging stops and the CHDONE flag is set. If the charging current falls below IEND for less than tEND and then rises above IEND again, the tEND timer resets. Recharge After the detection of charge complete, and the cessation of charging, the ADP5062 charger monitors the BAT_SNS pin as the battery discharges through normal use. If the BAT_SNS pin voltage falls to VRCH, the charger reactivates charging. Under most circumstances, triggering the recharge threshold results in the charger starting directly into fast charge constant voltage mode. The recharge function can be disabled in the I2C, but a status bit (Register Address 0x0C, Bit 3) informs the system that a recharge cycle is required. IC Enable/Disable The ADP5062 IC can be disabled by the DIG_IO2 digital input pin (if factory programmed to do so) or by the I2C registers. All internal control circuits are disabled when the IC is disabled. Disabling the IC1 option can also control the states of the LDO FET and the battery isolation FET. It is critical to note that during the disable IC1 mode, a high voltage at VINx passes to the internal supply voltage because all of the internal control circuits are disabled. The VINx supply voltage must fulfill the following condition: VISO_Bx < VINx < 5.5 V By default, the charging voltage limit is disabled and it can be enabled from I2C Register Address 0x08, Bit 5 (EN_CHG_VLIM). SYS_EN Output The ADP5062 features a SYS_EN open-drain FET to enable the system until the battery is at the minimum required level for guaranteed system start-up. When there are minimum battery voltage and/or minimum battery charge level requirements, the operation of SYS_EN can be set by I2C programming. The SYS_EN operation can be factory programmed to four different operating conditions as described in Table 11. Table 11. SYS_EN Mode Descriptions SYS_EN Mode Description Selection SYS_EN is activated when LDO is active and 00 system voltage is available. SYS_EN is activated by the ISO_Bx voltage, the 01 battery charging mode. 10 11 SYS_EN is activated and the isolation FET is disabled when the battery drops below VWEAK. This option is active when VINx = 0 V and the battery monitor is activated from Register 0x07, Bit 5 (EN_BMON). SYS_EN is active in LDO mode when the charger is disabled. SYS_EN is active in charging mode when VISO_Bx VWEAK. Indicator LED Output (ILED) Battery Charging Enable/Disable The ADP5062 charging function can be disabled by setting the I2C EN_CHG bit to low. The LDO to the system still operates under this circumstance and can be set in I2C to the default or I2C programmed system voltage from 4.3 V to 5.0 V (see Table 26 for details). The ADP5062 charging function can also be controlled via one of the external DIG_IOx pins (if factory programmed to do so). Any change in the I2C EN_CHG bit takes precedence over the pin setting. The ILED is an open-drain output for an indicator LED connection. Optionally, the ILED output can be used as a status output for a microcontroller. Indicator LED modes are listed in Table 12. Table 12. Indicator LED Operation Modes ADP5062 Mode IC Off LDO Mode Off LDO Mode On Charge Mode Timer Error (tTRK, tCHG, tSAFE) Overtemperature (TSD) Rev. B | Page 20 of 44 ILED Mode Off Off Off Continuously on Blinking Blinking On/Off Time 167 ms/833 ms 1 sec/1 sec Data Sheet ADP5062 THERMAL MANAGEMENT BATTERY ISOLATION FET Isothermal Charging The ADP5062 charger features an integrated battery isolation FET for power path control. The battery isolation FET isolates a deeply discharged Li-Ion cell from the system power supply in both trickle and fast charge modes, thereby allowing the system to be powered at all times. The ADP5062 includes a thermal feedback loop that limits the charge current when the die temperature exceeds TLIM (typically 115C). As the on-chip power dissipation and die temperature increase, the charge current is automatically reduced to maintain the die temperature within the recommended range. As the die temperature decreases due to lower on-chip power dissipation or ambient temperature, the charge current returns to the programmed level. During isothermal charging, the THERM_LIM I2C flag is set to high. This thermal feedback control loop allows the user to set the programmed charge current based on typical rather than worst case conditions. The ADP5062 does not include a thermal feedback loop to limit ISO_Sx load current in LDO mode. If the power dissipated on chip during LDO mode causes the die temperature to exceed 130C, an interrupt is generated. If the die temperature continues to rise beyond 140C, the device enters thermal shutdown. Thermal Shutdown and Thermal Early Warning The ADP5062 charger features a thermal shutdown threshold detector. If the die temperature exceeds TSD, the ADP5062 charger is disabled, and the TSD 140C bit is set. The ADP5062 charger can be reenabled when the die temperature drops below the TSD falling limit and the TSD 140C bit is reset. To reset the TSD 140C bit, write to the I2C fault register, Register Address 0x0D (Bit 0) or cycle the power. Before the die temperature reaches TSD, the early warning bit is set if TSDL is exceeded. This allows the system to accommodate power consumption before thermal shutdown occurs. Fault Recovery Before performing the following operation, it is important to ensure that the cause of the fault has been rectified. To recover from a charger fault (when CHARGER_STATUS[2:0] = 110), cycle power on VINx or write high to reset the I2C fault bits in the fault register (Register Address 0x0D). When VINx is below VVIN_OK_RISE, the battery isolation FET is in full conducting mode. The battery isolation FET is off during trickle charge mode. When the battery voltage exceeds VTRK_DEAD, the battery isolation FET switches to the system voltage regulation mode. During system voltage regulation mode, the battery isolation FET maintains the VISO_SFC voltage on the ISO_Sx pins. When the battery voltage exceeds VISO_SFC, the battery isolation FET is in full conducting mode. The battery isolation FET supplements the battery to support high current functions on the system power supply. When the voltage on ISO_Sx drops below VISO_Bx, the battery isolation FET enters into full conducting mode. When voltage on ISO_Sx rises above VISO_Bx, the isolation FET enters regulating mode or full conduction mode, depending on the Li-Ion cell voltage and the linear charger mode. BATTERY DETECTION Battery Voltage Level Detection The ADP5062 charger features a battery detection mechanism to detect an absent battery. The charger actively sinks and sources current into the ISO_Bx node, and voltage vs. time is detected. The sink phase is used to detect a charged battery, whereas the source phase is used to detect a discharged battery. The sink phase (see Figure 30) sinks ISINK current from the ISO_Bx pins for a time period, tBATOK. If ISO_Bx is below VBATL when the tBATOK timer expires, the charger assumes no battery is present and starts the source phase. If the ISO_Bx pin exceeds the VBATL voltage when the tBATOK timer expires, the charger assumes the battery is present and begins a new charge cycle. The source phase sources ISOURCE current to the ISO_Bx pins for a time period, tBATOK. If If ISO_Bx exceeds VBATH before the tBATOK timer expires, the charger assumes that no battery is present. If the ISO_Bx pin does not exceed the VBATH voltage when the tBATOK timer expires, the charger assumes that a battery is present and begins a new charge cycle. Rev. B | Page 21 of 44 ADP5062 Data Sheet SOURCE PHASE VBATL LOGIC STATUS tBAT_OK VBATH ISOURCE SINK PHASE LOGIC STATUS tBAT_OK OPEN OR SHORT OPEN ISO_Bx 10806-030 OPEN OPEN ISINK ISO_Bx Figure 30. Sink Phase ISO_Bx SHORT OR LOW BATTERY tBAT_SHR SHORT ISO_Bx 10806-031 tBAT_OK LOGIC STATUS SHORT OPEN OR SHORT SHORT SHORT ISINK tBAT_OK LOGIC STATUS ISOURCE LOGIC STATUS ISO_Bx TRICKLE CHARGE VBAT_SHR SOURCE PHASE VBATH VBATL ITRK_DEAD SINK PHASE Figure 31. Trickle Charge Battery (ISO_Bx) Short Detection A battery short occurs under a damaged battery condition or when the battery protection circuitry is enabled. On commencing trickle charging, the ADP5062 charger monitors the battery voltage. If this battery voltage does not exceed VBAT_SHR within the specified timeout period, tBAT_SHR, a fault is declared and the charger is stopped by turning the battery isolation FET off, but the system voltage is maintained at VISO_STRK by the linear regulator. The battery pack temperature sensing can be controlled by I2C, using the conditions shown in Table 13. Note that the I2C register default setting for EN_THR (Register Address 0x07) is 0 = temperature sensing off. Table 13. THR Input Function Conditions VINx Open or VIN = 0 V to 4.0 V Open or VIN = 0 V to 4.0 V 4.0 V to 6.7 V VISO_Bx <2.5 V >2.5 V Don't care THR Function Off Off, controlled by I2C Always on After source phase, if the ISO_Bx or BAT_SNS level remains below VBATH, either the battery voltage is low or the battery node is shorted. Because the battery voltage is low, trickle charging mode is initiated (see Figure 31). If the BAT_SNS level remains below VBAT_SHR after tBAT_SHR has elapsed, the ADP5062 assumes that the battery node is shorted. If the battery pack thermistor is not connected directly to the THR pin, a 10 k (tolerance 20%) dummy resistor must be connected between the THR input and GND. Leaving the THR pin open results in a false detection of the battery temperature being <0C and charging is disabled. The trickle charge branch is active during the battery short scenario, and trickle charge current to the battery is maintained until the 60-minute trickle charge mode timer expires. The ADP5062 charger monitors the voltage in the THR pin and suspends charging when the current is outside the range of less than 0C or greater than 60C. BATTERY PACK TEMPERATURE SENSING The ADP5062 charger is designed for use with an NTC thermistor in the battery pack with a nominal room temperature value of either 10 k at 25C or 100 k at 25C, which is selected by factory programming. Battery Thermistor Input The ADP5062 charger features battery pack temperature sensing that precludes charging when the battery pack temperature is outside the specified range. The THR pin provides an on and off switching current source that should be connected directly to the battery pack thermistor terminal. The activation interval of the THR current source is 167 ms. The ADP5062 charger is designed for use with an NTC thermistor in the battery pack with a temperature coefficient curve (beta). Factory programming supports eight beta values covering a range from 3150 to 4400 (see Table 43). Rev. B | Page 22 of 44 Data Sheet ADP5062 JEITA Li-Ion Battery Temperature Charging Specification The ADP5062 is compliant with the JEITA1 and JEITA2 Li-Ion battery charging temperature specifications as outlined in Table 14 and Table 16, respectively. JEITA function can be enabled via the I2C interface and, optionally, the JEITA1 or JEITA2 function can be selected in I2C. Alternatively, the JEITA1 or JEITA2 can be set as enabled to default by factory programming. When the ADP5062 identifies a hot or cold battery condition, the ADP5062 takes the following actions: * * Stops charging the battery. Connects or enables the battery isolation FET such that the ADP5062 continues in LDO mode. Table 14. JEITA1 Specifications Parameter JEITA1 Cold Temperature Limits JEITA1 Cool Temperature Limits Symbol IJEITA_COLD IJEITA_COOL JEITA1 Typical Temperature Limits IJEITA_TYP JEITA1 Warm Temperature Limits IJEITA_WARM JEITA1 Hot Temperature Limits IJEITA_HOT Conditions No battery charging occurs. Battery charging occurs at approximately 50% of the programmed level. See Table 15 for specific charging current reduction levels. Normal battery charging occurs at the default/programmed levels. Min 0 Max 0 10 Unit C C 10 45 C Battery termination voltage (VTRM) is reduced by 100 mV from the programmed value. No battery charging occurs. 45 60 C 60 C Table 15. JEITA1 Reduced Charge Current Levels, Battery Cool Temperature ICHG[4:0] (Default) 00000 = 50 mA 00001 = 100 mA 00010 = 150 mA 00011 = 200 mA 00100 = 250 mA 00101 = 300 mA 00110 = 350 mA 00111 = 400 mA 01000 = 450 mA 01001 = 500 mA 01010 = 550 mA 01011 = 600 mA ICHG JEITA1 50 mA 50 mA 50 mA 100 mA 100 mA 150 mA 150 mA 200 mA 200 mA 250 mA 250 mA 300 mA ICHG[4:0] (Default) 01100 = 650 mA 01101 = 700 mA 01110 = 750 mA 01111 = 800 mA 10000 = 850 mA 10001 = 900 mA 10010 = 950 mA 10011 = 1000 mA 10100 = 1050 mA 10101 = 1100 mA 10110 = 1200 mA 10111 = 1300 mA ICHG JEITA1 300 mA 350 mA 350 mA 400 mA 400 mA 450 mA 450 mA 500 mA 500 mA 550 mA 600 mA 650 mA Table 16. JEITA2 Specifications Parameter JEITA2 Cold Temperature Limits JEITA2 Cool Temperature Limits Symbol IJEITA_COLD IJEITA_COOL JEITA2 Typical Temperature Limits JEITA2 Warm Temperature Limits IJEITA_TYP IJEITA_WARM JEITA2 Hot Temperature Limits IJEITA_HOT Conditions No battery charging occurs. Battery termination voltage (VTRM) is reduced by 100 mV from the programmed value. Normal battery charging occurs at the default/programmed levels. Battery termination voltage (VTRM) is reduced by 100 mV from the programmed value. No battery charging occurs. Rev. B | Page 23 of 44 Min 0 Max 0 10 Unit C C 10 45 45 60 C C 60 C ADP5062 Data Sheet POWER-ON RESET RESET ALL REGISTERS NO NO IC OFF VIN_OK = HIGH SYSTEM OFF YES YES ENABLE CHARGER NO ENABLE LDO YES ENABLE CHARGER LDO MODE NO YES YES NO VBAT_SNS < VCHG_VLIM NO YES TO CHARGING MODE Figure 32. Simplified Battery and VINx Connect Flowchart Rev. B | Page 24 of 44 10806-032 LOW BATTERY CHG Data Sheet ADP5062 TO CHARGING MODE TO IC OFF YES RUN BATTERY DETECTION tSTART NO EXPIRED YES VBAT_SNS < VTRK NO POWER-DOWN TRICKLE CHARGE VIN_OK = HIGH FAST CHARGE NO VIN_OK = HIGH YES VBAT_SNS < VTRK YES NO IVINx < ILIM YES NO VIN_ILIM = HIGH IVINx = ILIM NO THERM_LIM = HIGH TEMP = TLIM YES YES WATCHDOG EXPIRED START tSAFE IBUS = 100mA NO tWD EXPIRED TEMP < TLIM NO YES TIMER FAULT OR BAD BATTERY YES tSAFE OR tTRK EXPIRED tWD EXPIRED YES NO WATCHDOG EXPIRED START tSAFE IBUS = 100 mA NO tSAFE OR tCHG YES1 EXPIRED NO RUN BATTERY DETECTION VBAT_SNS = VTRM YES NO CC MODE CHARGING NO CV MODE CHARGING CHARGE COMPLETE YES IOUT < IEND Figure 33. Simplified Charging Mode Flowchart Rev. B | Page 25 of 44 10806-033 YES VBAT_SNS = VRCH NO TIMER FAULT OR BAD BATTERY 1SEE TIMER SPECS ADP5062 Data Sheet I2C INTERFACE the master after the 8-bit data byte has been written (see Figure 34 for an example of the I2C write sequence to a single register). The ADP5062 increments the subaddress automatically and starts receiving a data byte at the next register until the master sends an I2C stop as shown in Figure 35. The ADP5062 includes an I2C-compatible serial interface for control of the charging and LDO functions, as well as for a readback of the system status registers. The I2C chip address is 0x28 in write mode and 0x29 in read mode. Figure 36 shows the I2C read sequence of a single register. ADP5062 sends the data from the register denoted by the subaddress and increments the subaddress automatically, sending data from the next register until the master sends an I2C stop condition, as shown in Figure 37. Register values are reset to the default values when the VINx supply falls below the falling voltage threshold, VVIN_OK_FALL. The I2C registers also reset when the battery is disconnected and VIN is 0 V. The subaddress content selects which of the ADP5062 registers is written to first. The ADP5062 sends an acknowledgement to MASTER STOP 0 = WRITE 0 1 0 CHIP ADDRESS 0 0 0 0 SUBADDRESS 0 SP ADP5062 RECEIVES DATA 10806-034 1 ADP5062 ACK 0 ADP5062 ACK 0 ADP5062 ACK ST Figure 34. I2C Single Register Write Sequence 0 = WRITE 0 0 0 0 CHIP ADDRESS 0 SUBADDRESS REGISTER N 0 0 ADP5062 RECEIVES DATA TO REGISTER N ADP5062 RECEIVES DATA TO REGISTER N + 1 0 SP ADP5062 RECEIVES DATA TO LAST REGISTER 10806-035 1 ADP5062 ACK 0 ADP5062 ACK 1 ADP5062 ACK 0 ADP5062 ACK 0 ADP5062 ACK ST MASTER STOP Figure 35. I2C Multiple Register Write Sequence CHIP ADDRESS 0 1 SP MASTER ACK SUBADDR ESS 0 ADP5062 ACK CHIP ADDRESS 0 ST 0 0 1 0 1 0 0 1 ADP5062 ACK 0 1 0 1 0 0 0 0 ADP5062 ACK ST 0 MASTER STOP 1 = READ ADP5062 SEND SDATA 10806-036 0 = WRITE Figure 36. I2C Single Register Read Sequence Figure 37. I2C Multiple Register Read Sequence Rev. B | Page 26 of 44 ADP5062 SENDS DATA OF REGISTER N+1 ADP5062 SENDS DATA OF LAST REGISTER 10806-037 ADP5062 SENDS DATA OF REGISTER N 1 SP MASTER ACK CHIP ADDRESS 0 MASTER ACK SUBADDRESS REGISTER N 0 MASTER ACK CHIP ADDRESS 0 ST 0 0 1 0 1 0 0 1 0 0 ADP5062 ACK 0 0 1 0 1 0 0 0 0 ADP5062 ACK ST MASTER STOP 1 = READ ADP5062 ACK 0 = WRITE Data Sheet ADP5062 I2C REGISTER MAP See the Factory-Programmable Options section for programming option details. Note that a blank cell indicates a bit that is not used or is reserved for future use. Table 17. I2C Register Map Register Addr. Name 0x00 Manufacturer and model ID 0x01 Silicon revision 0x02 VINx pin settings 0x03 Termination settings 0x04 Charging current settings 0x05 Voltage thresholds 0x06 Timer settings 0x07 Functional Settings 1 0x08 Functional Settings 2 0x09 Interrupt enable 0x0A Interrupt active 0x0B Charger Status 1 0x0C Charger Status 2 0x0D Fault 0x10 0x11 Battery short IEND D7 D6 D5 MANUF[3:0] D4 D3 D2 D1 Model[3:0] D0 REV[3:0] ILIM[3:0] 1 VTRM[5:0]1, 2 CHG_VLIM[1:0]1, 2 ICHG[4:0]1, 2 DIS_RCH1, 3 VRCH[1:0]1 DIS_IC11 EN_JEITA1, 3 JEITA_SELECT1, 3 VIN_OV ITRK_DEAD[1:0]1 VTRK_DEAD[1:0]1, 3 VWEAK[2:0]1 EN_TEND1 EN_CHG_TIMER1 CHG_TMR_PERIOD1 EN_WD1, 3 EN_BMON1 EN_THR1 DIS_LDO1 EN_EOC1 IDEAL_DIODE[1:0]1, 3 EN_CHG_VLIM1, 3 WD_PERIOD1 RESET_WD EN_CHG1 VSYSTEM[2:0]1, 3 EN_THERM_LIM_INT EN_WD_INT EN_TSD_INT EN_THR_INT EN_BAT_INT EN_CHG_INT EN_VIN_INT THERM_LIM_INT WD_INT TSD_INT THR_INT BAT_INT VIN_OK VIN_ILIM THERM_LIM CHDONE CHARGER_STATUS[2:0] RCH_LIM_INFO BATTERY_STATUS[2:0] THR_STATUS[2:0] BAT_SHR1 CHG_INT TSD 130C1 TBAT_SHR[2:0]1 VIN_INT TSD 140C1 VBAT_SHR[2:0]1 IEND[2:0]1, 3 C/20 EOC1 These bits reset to default I2C values when VINx is connected or disconnected. The default I2C values of these bits are partially factory programmable. 3 The default I2C values of these bits are fully factory programmable. 1 2 Rev. B | Page 27 of 44 C/10 EOC1 C/5 EOC1 SYS_EN_SET[1:0]1, 3 ADP5062 Data Sheet REGISTER BIT DESCRIPTIONS In Table 18 through Table 33, the following abbreviations are used: R is read only, W is write only, R/W is read/write, and N/A means not applicable. Table 18. Manufacturer and Model ID, Register Address 0x00 Bit No. [7:4] [3:0] Bit Name MANUF[3:0] MODEL[3:0] Access R R Default 0001 1001 Description The 4-bit manufacturer identification bus The 4-bit model identification bus Table 19. Silicon Revision, Register Address 0x01 Bit No. [7:4] [3:0] Bit Name Not used REV[3:0] Access R R Default Description 0100/ADP5062ACPZ-1-R7 0111/ADP5062ACPZ-2-R7 The 4-bit silicon revision identification bus Table 20. VINx Pin Settings, Register Address 0x02 Bit No. [7:5] 4 [3:0] Bit Name Not used RFU ILIM[3:0] Access R R/W R/W Default Description 0 0000 = 100 mA Reserved for future use. VINx input current-limit programming bus. The current into VINx can be limited to the following programmed values: 0000 = 100 mA. 0001 = 150 mA. 0010 = 200 mA. 0011 = 250 mA. 0100 = 300 mA. 0101 = 400 mA. 0110 = 500 mA. 0111 = 600 mA. 1000 = 700 mA. 1001 = 800 mA. 1010 = 900 mA. 1011 = 1000 mA. 1100 = 1200 mA. 1101 = 1500 mA. 1110 = 1800 mA. 1111 = 2100 mA. Rev. B | Page 28 of 44 Data Sheet ADP5062 Table 21. Termination Settings, Register Address 0x03 Bit No. [7:2] Bit Name VTRM[5:0] Access R/W Default 100011 = 4.20 V [1:0] CHG_VLIM[1:0] R/W 00 = 3.2 V Description Termination voltage programming bus. The values of the floating voltage can be programmed to the following values: 000101 = 3.60 V. 000110 = 3.62 V. 000111 = 3.64 V. 001000 = 3.66 V. 001001 = 3.68 V. 001010 = 3.70 V. 001011 = 3.72 V. 001100 = 3.74 V. 001101 = 3.76 V. 001110 = 3.78 V. 001111 = 3.80 V. 010000 = 3.82 V. 010001 = 3.84 V. 010010 = 3.86 V. 010011 = 3.88 V. 010100 = 3.90 V. 010101 = 3.92 V. 010110 = 3.94 V. 010111 = 3.96 V. 011000 = 3.98 V. 011001 = 4.00 V. 011010 = 4.02 V. 011011 = 4.04 V. 011100 = 4.06 V. 011101 = 4.08 V. 011110 = 4.10 V. 011111 = 4.12 V. 100000 = 4.14 V. 100001 = 4.16 V. 100010 = 4.18 V. 100011 = 4.20 V. 100100 = 4.22 V. 100101 = 4.24 V. 100110 = 4.26 V. 100111 = 4.28 V. 101000 = 4.30 V. 101001 = 4.32 V. 101010 = 4.34 V. 101011 = 4.36 V. 101100 = 4.38 V. 101101 = 4.40 V. 101110 = 4.42 V. 101111 = 4.44 V. 110000 = 4.44 V. 110001 = 4.46 V. 110010 = 4.48 V. 110011 to 111111 = 4.50 V. Charging voltage limit programming bus. The values of the charging voltage limit can be programmed to the following values: 00 = 3.2 V. 01 = 3.4 V. 10 = 3.7 V. 11 = 3.8 V. Rev. B | Page 29 of 44 ADP5062 Data Sheet Table 22. Charging Current Settings, Register Address 0x04 Bit No. 7 [6:2] Bit Name Not used ICHG[4:0] Access R R/W Default Description 01110 = 750 mA [1:0] ITRK_DEAD[1:0] R/W 10 = 20 mA Fast charge current programming bus. The values of the constant current charge can be programmed to the the following values: 00000 = 50 mA. 00001 = 100 mA. 00010 = 150 mA. 00011 = 200 mA. 00100 = 250 mA. 00101 = 300 mA. 00110 = 350 mA. 00111 = 400 mA. 01000 = 450 mA. 01001 = 500 mA. 01010 = 550 mA. 01011 = 600 mA. 01100 = 650 mA. 01101 = 700 mA. 01110 = 750 mA. 01111 = 800 mA. 10000 = 850 mA. 10001 = 900 mA. 10010 = 950 mA. 10011 = 1000 mA. 10100 = 1050 mA. 10101 = 1100 mA. 10110 = 1200 mA. 10111 to 11111 = 1300 mA. Trickle and weak charge current programming bus. The values of the trickle and weak charge currents can be programmed to the following values: 00 = 5 mA. 01 = 10 mA. 10 = 20 mA. 11 = 80 mA. Table 23. Voltage Thresholds, Register Address 0x05 Bit No. 7 Bit Name DIS_RCH Access R/W Default 0 = recharge enabled [6:5] VRCH[1:0] R/W 11 = 260 mV Description 0 = recharge enabled. 1 = recharge disabled. Recharge voltage programming bus. The values of the recharge threshold can be programmed to the following values (note that the recharge cycle can be disabled in I2C by using the DIS_RCH bit): 00 = 80 mV. 01 = 140 mV. 10 = 200 mV. 11 = 260 mV. Rev. B | Page 30 of 44 Data Sheet ADP5062 Bit No. [4:3] Bit Name VTRK_DEAD[1:0] Access R/W Default 01 = 2.5 V [2:0] VWEAK[2:0] R/W 011 = 3.0 V Description Trickle to fast charge dead battery voltage programming bus. The values of the trickle to fast charge threshold can be programmed to the following values: 00 = 2.0 V. 01 = 2.5 V. 10 = 2.6 V. 11 = 2.9 V. Weak battery voltage rising threshold. 000 = 2.7 V. 001 = 2.8 V. 010 = 2.9 V. 011 = 3.0 V. 100 = 3.1 V. 101 = 3.2 V. 110 = 3.3 V. 111 = 3.4 V. Table 24. Timer Settings, Register Address 0x06 Bit No. [7:6] 5 Bit Name Not used EN_TEND Access Default Description R/W 1 4 EN_CHG_TIMER R/W 1 3 CHG_TMR_PERIOD R/W 1 2 EN_WD R/W 0 1 WD_PERIOD R/W 0 0 RESET_WD W 0 0 = charge complete timer, tEND, disabled. A 31 ms deglitch timer remains on. 1 = charge complete timer enabled. 0 = trickle/fast charge timer disabled. 1 = trickle/fast charge timer enabled. Trickle and fast charge timer period. 0 = 30 sec trickle charge timer and 300 minute fast charge timer. 1 = 60 sec trickle charge timer and 600 minute fast charge timer. 0 = watchdog timer is disabled even when BAT_SNS exceeds VWEAK. 1 = watchdog timer safety timer is enabled. Watchdog safety timer period. 0 = 32 sec watchdog timer and 40 minute safety timer. 1 = 64 sec watchdog timer and 40 minute safety timer. When RESET_WD is set to logic high by I2C, the watchdog safety timer is reset. Table 25. Functional Settings 1, Register Address 0x07 Bit No. 7 6 Bit Name Not used DIS_IC1 Access Default Description R/W 0 5 EN_BMON R/W 0 4 EN_THR R/W 0 3 DIS_LDO R/W 0 0 = normal operation. 1 = the ADP5062 is disabled; VVINx must be VISO_Bx < VVINx < 5.5 V. 0 = when VVINx < VVIN_OK_RISE or VVIN_OK_FALL, the battery monitor is disabled. When VVINx = 4.0 V to 6.7 V, the battery monitor is enabled regardless of the EN_BMON state. 1 = the battery monitor is enabled even when the voltage at the VINx pins is below VVIN_OK. 0 = when VVINx < VVIN_OK_RISE or VVIN_OK_FALL, the THR current source is disabled. When VVINx = 4.0 V to 6.7 V, the THR current source is enabled regardless of the EN_THR state. 1 = THR current source is enabled even when the voltage at the VINx pins is below VVIN_OK_RISE or VVIN_OK_FALL. 0 = LDO is enabled. 1 = LDO is off. In addition, if EN_CHG = low, the battery isolation FET is on. If EN_CHG = high, the battery isolation FET is off. Rev. B | Page 31 of 44 ADP5062 Data Sheet Bit No. 2 Bit Name EN_EOC Access R/W Default 1 Description 0 = end of charge not allowed. 1 = end of charge allowed. 1 0 Not used EN_CHG R/W 0 0 = battery charging is disabled. 1 = battery charging is enabled. Table 26. Functional Settings 2, Register Address 0x08 Bit No. 7 Bit Name EN_JEITA Access R/W Default 0 = JEITA disabled 6 JEITA_SELECT R/W 0 = JEITA1 5 EN_CHG_VLIM R/W 0 [4:3] IDEAL_DIODE[1:0] R/W 00 [2:0] VSYSTEM[2:0] R/W See Table 41 for model specific default value. Description 0 = JEITA compliance of the Li-Ion temperature battery charging specifications is disabled. 1 = JEITA compliance enabled. 0 = JEITA1 is selected. 1 = JEITA2 is selected. 0 = charging voltage limit disabled. 1 = voltage limit activated. The charger prevents charging until the battery voltage drops below the VCHG_VLIM threshold. 00 = ideal diode operates constantly when VISO_Sx < VISO_Bx. 01 = ideal diode operates when VISO_Sx < VISO_Bx and VBAT_SNS > VWEAK. 10 = ideal diode is disabled. 11 = ideal diode is disabled. System voltage programming bus. The values of the system voltage can be programmed to the following values: 000 = 4.3 V. 001 = 4.4 V. 010 = 4.5 V. 011 = 4.6 V. 100 = 4.7 V. 101 = 4.8 V. 110 = 4.9 V. 111 = 5.0 V. Table 27. Interrupt Enable, Register Address 0x09 Bit No. 7 6 Bit Name Not used EN_THERM_LIM_INT Access Default Description R/W 0 5 EN_WD_INT R/W 0 4 EN_TSD_INT R/W 0 3 EN_THR_INT R/W 0 2 EN_BAT_INT R/W 0 1 EN_CHG_INT R/W 0 0 EN_VIN_INT R/W 0 0 = isothermal charging interrupt is disabled. 1 = isothermal charging interrupt is enabled. 0 = watchdog alarm interrupt is disabled. 1 = watchdog alarm interrupt is enabled. 0 = overtemperature interrupt is disabled. 1 = overtemperature interrupt is enabled. 0 = THR temperature thresholds interrupt is disabled. 1 = THR temperature thresholds interrupt is enabled. 0 = battery voltage thresholds interrupt is disabled. 1 = battery voltage thresholds interrupt is enabled. 0 = charger mode change interrupt is disabled. 1 = charger mode change interrupt is enabled. 0 = VINx pin voltage thresholds interrupt is disabled. 1 = VINx pin voltage thresholds interrupt is enabled. Rev. B | Page 32 of 44 Data Sheet ADP5062 Table 28. Interrupt Active, Register Address 0x0A Bit No. 7 6 5 Bit Name Not used THERM_LIM_INT WD_INT Access Default Description R R 0 0 4 3 2 1 0 TSD_INT THR_INT BAT_INT CHG_INT VIN_INT R R R R R 0 0 0 0 0 1 = indicates an interrupt caused by isothermal charging. 1 = indicates an interrupt caused by the watchdog alarm. The watchdog timer expires within 2 sec or 4 sec, depending on the watch dog period setting of 32 sec or 64 sec, respectively. 1 = indicates an interrupt caused by an overtemperature fault. 1 = indicates an interrupt caused by THR temperature thresholds. 1 = indicates an interrupt caused by battery voltage thresholds. 1 = indicates an interrupt caused by a charger mode change. 1 = indicates an interrupt caused by VINx voltage thresholds. Table 29. Charger Status 1, Register Address 0x0B Bit No. 7 6 5 Bit Name VIN_OV VIN_OK VIN_ILIM Access R R R Default N/A N/A N/A 4 THERM_LIM R N/A 3 CHDONE R N/A [2:0] CHARGER_STATUS[2:0] R N/A Description 1 = the voltage at the VINx pins exceeds VVIN_OV. 1 = the voltage at the VINx pins exceeds VVIN_OK_RISE, VVIN_OK_FALL. 1 = the current into a VINx pin is limited by the high voltage blocking FET and the charger is not running at the full programmed ICHG. 1 = the charger is not running at the full programmed ICHG but is limited by the die temperature. 1 = the end of a charge cycle has been reached. This bit latches on, in that it does not reset to low when the VRCH threshold is breached. Charger status bus. 000 = off. 001 = trickle charge. 010 = fast charge (CC mode). 011 = fast charge (CV mode). 100 = charge complete. 101 = LDO mode. 110 = trickle or fast charge timer expired. 111 = battery detection. Rev. B | Page 33 of 44 ADP5062 Data Sheet Table 30. Charger Status 2, Register Address 0x0C Bit No. [7:5] Mnemonic THR_STATUS[2:0] Access R Default N/A Description THR pin status. 000 = off. 001 = battery cold. 010 = battery cool. 011 = battery warm. 100 = battery hot. 111 = thermistor OK. 4 3 Not used RCH_LIM_INFO R N/A [2:0] BATTERY_STATUS[2:0] R The recharge limit information function is activated when DIS_RCH is logic high and the CHARGER_STATUS[2:0] = 100 (binary). The status bit informs the system that a recharge cycle is required. 0 = VBAT_SNS > VRCH 1 = VBAT_SNS < VRCH Battery status bus. 000 = battery monitor off. 001 = no battery. 010 = VBAT_SNS < VTRK_DEAD. 011 = VTRK_DEAD VBAT_SNS < VWEAK. 100 = VBAT_SNS VWEAK. Access Default Description R/W R/W R/W R/W 0 1 = indicates detection of a battery short. 0 0 1 = indicates an overtemperature (lower) fault. 1 = indicates an overtemperature fault. Table 31. Fault, 1 Register Address 0x0D Bit No. [7:4] 3 2 1 0 1 Bit Name Not used BAT_SHR Not used TSD 130C TSD 140C To reset the fault bits in the fault register, cycle power on VINx or write high to the corresponding I2C bit. Table 32. Battery Short, Register Address 0x10 Bit No. [7:5] Bit Name TBAT_SHR[2:0] Access R/W Default 100 = 30 sec Description Battery short timeout timer. 000 = 1 sec. 001 = 2 sec. 010 = 4 sec. 011 = 10 sec. 100 = 30 sec. 101 = 60 sec. 110 = 120 sec. 111 = 180 sec. [4:3] [2:0] Not used VBAT_SHR[2:0] R/W 100 = 2.4 V Battery short voltage threshold level. 000 = 2.0 V. 001 = 2.1 V. 010 = 2.2 V. 011 = 2.3 V. 100 = 2.4 V. 101 = 2.5 V. 110 = 2.6 V. 111 = 2.7 V. Rev. B | Page 34 of 44 Data Sheet ADP5062 Table 33. IEND, Register Address 0x11 Bit No. [7:5] Bit Name IEND[2:0] Access R/W Default 010 = 52.5 mA 4 C/20 EOC R/W 0 3 C/10 EOC R/W 0 2 C/5 EOC R/W 0 1:0 SYS_EN_SET[1:0] R/W 00 1 Description Termination current programming bus. The values of the termination current can be programmed to the following values: 000 = 12.5 mA. 001 = 32.5 mA. 010 = 52.5 mA. 011 = 72.5 mA. 100 = 92.5 mA. 101 = 117.5 mA. 110 = 142.5 mA. 111 = 170.0 mA. The C/20 EOC bit has priority over the other settings (C/5 EOC, C/10 EOC, and IEND[2:0]). 1 = the termination current is ICHG[4:0] / 20 with the following limitations: Minimum value = 12.5 mA. Maximum value = 170 mA. The C/10 EOC bit has priority over the other termination current settings (C/5 EOC and IEND[2:0]), but does not have priority over the C/20 EOC setting. 1 = the termination current is ICHG[4:0] / 10, unless C/20 EOC is high. The termination current is limited to the following values: Minimum value = 12.5 mA. Maximum value = 170 mA. The C/5 EOC bit has priority over the other termination current settings (IEND[2:0]) but does not have priority over the C/20 EOC setting or the C/10 EOC setting. 1 = the termination current is ICHG[4:0] / 5, unless the C/20 EOC or the C/10 EOC bit is high. The termination current is limited to the following values: Minimum value = 12.5 mA. Maximum value = 170 mA. Selects the operation of the system enable pin (SYS_EN). 00 = SYS_EN is activated when LDO is active and the system voltage is available. 01 = SYS_EN is activated by the ISO_Bx voltage, the battery charging mode. 10 = SYS_EN is activated and the isolation FET is disabled when the battery drops below VWEAK. 1 11 = SYS_EN is active in LDO mode when the charger is disabled. SYS_EN is active in the charging mode when VISO_Bx VWEAK. This option is active when VINx = 0 V and the battery monitor is activated from Register 0x07, Bit 5 (EN_BMON). Rev. B | Page 35 of 44 ADP5062 Data Sheet APPLICATIONS INFORMATION Substituting these values in the equation yields EXTERNAL COMPONENTS CEFF = 16 F x (1 - 0.15) x (1 - 0.1) 12.24 F ISO_Sx (VOUT) Capacitor Selection To obtain stable operation of the ADP5062 in a safe way, the combined effective capacitance of the ISO_Sx capacitor and the system capacitance must not be less than 10 F and must not exceed 100 F at any point during operation. When choosing the capacitor value, it is also important to account for the loss of capacitance caused by the output voltage dc bias. Ceramic capacitors are manufactured with a variety of dielectrics, each with a different behavior over temperature and applied voltage. Capacitors must have a dielectric that is adequate to ensure the minimum capacitance over the necessary temperature range and dc bias conditions. X5R or X7R dielectrics with a voltage rating of 6.3 V or higher are recommended for best performance. Y5V and Z5U dielectrics are not recommended for use with any dcto-dc converter because of their poor temperature and dc bias characteristics. To guarantee the performance of the charger in various operating modes, including trickle charge, constant current charge, and constant voltage charge, it is imperative that the effects of dc bias, temperature, and tolerances on the behavior of the capacitors be evaluated for each application. Splitting ISO_Sx Capacitance In many applications, the total ISO_Sx capacitance consists of a number of capacitors. The system voltage node (ISO_Sx) usually supplies a single regulator or a number of ICs and regulators, each of which requires a capacitor close to its power supply input (see Figure 39). The capacitance close to the ADP5062 ISO_Sx output should be at least 5 F, as long as the total effective capacitance is at least 10 F at any point during operation. The worst case capacitance accounting for capacitor variation over temperature, component tolerance, and voltage is calculated using the following equation: ISO_Sx ISO_Bx where: CEFF is the effective capacitance at the operating voltage. TEMPCO is the worst case capacitor temperature coefficient. TOL is the worst case component tolerance. 60 IC1 + SUM OF EFFECTIVE CAPACITANCES ON ISO_Sx NODE > 10F CISO_Bx 10F VIN2 IC2 10806-038 CIN2 Figure 39. Splitting ISO_Sx Capacitance ISO_Bx and ISO_Sx Capacitor Selection 40 The ISO_Bx and the ISO_Sx effective capacitance (including temperature and dc bias effects) must not be less than 10 F at any point during operation. Typically, a nominal capacitance of 22 F is required to fullfill the condition at all points of operation. Suggestions for ISO_Bx and ISO_Sx capacitors are listed in Table 34. 35 CBP Capacitor Selection 55 50 CAPACITANCE (F) VIN1 CIN1 ADP5062 CEFF = COUT x (1 - TEMPCO) x (1 - TOL) In this example, the worst case temperature coefficient (TEMPCO) over the range of -40C to +85C is assumed to be 15% for an X5R dielectric. The tolerance of the capacitor (TOL) is assumed to be 10%, and COUT is 16 F at 4.2 V, as shown in Figure 38. CISO_Sx > 5F 45 30 20 0 1 2 3 DC BIAS VOLTAGE (V) 4 5 10806-041 25 Figure 38. Murata GRM31CR61A226KE19 Capacitance vs. Bias Voltage The internal supply voltage of the ADP5062 is equipped with a noise suppressing capacitor at the CBP terminal. Do not allow CBP capacitance to exceed 14 nF at any point during operation. Do not connect any external voltage source, any resistive load, or any other current load to the CBP terminal. Suggestions for a CBP capacitor are listed in Table 35. Rev. B | Page 36 of 44 Data Sheet ADP5062 VINx Capacitor Selection According to the USB 2.0 specification, USB peripherals have a detectable change in capacitance on VBUS when they are attached to a USB port. The peripheral device VBUS bypass capacitance must be at least 1 F but not larger than 10 F. The VINx input of the ADP5062 is tolerant of voltages as high as 20 V; however, if an application requires exposing the VINx input to voltages of up to 20 V, the voltage range of the capacitor must also be above 20 V. Suggestions for a VINx capacitor are given in Table 36. When using ceramic capacitors, a higher voltage range is usually achieved by selecting a component with larger physical dimensions. In applications where lower than 20 V at VINx input voltages can be guaranteed, smaller output capacitors can be used accordingly. Table 34. ISO_Bx and ISO_Sx Capacitor Suggestions Vendor Murata Murata TDK TaiyoYuden Part Number GRM31CR61A226KE19 GRM31CR60J226ME19 C3216X5R0J226M JMK316ABJ226KL Value 22 F 22 F 22 F 22 F Voltage 10 V 6.3 V 6.3 V 6.3 V Size 1206 1206 1206 1206 Voltage 16 V 16 V Size 0402 0402 Voltage 25 V 25 V Size 0805 0805 Table 35. CBP Capacitor Suggestions Vendor Murata TDK Part Number GRM15XR71C103KA86 C1005X7R1C103K Value 10 nF 10 nF Table 36. VINx Capacitor Suggestions Vendor Murata TDK Rev. B | Page 37 of 44 Part Number GRM21BR61E106MA73 C2012X5R1E106K Value 10 F 10 F ADP5062 Data Sheet PCB LAYOUT GUIDELINES VIN = 4V TO 7V C4 10F GRM21BR6E106MA73 8 7 6 VIN1 TO VIN3 ADP5062 20-LEAD LFCSP 19 ISO_S1 TO ISO_S3 CBP C1 10nF 9 10 GRM15XR71C103KA8 11 C3 22F GRM31CR60J226ME19 VDDIO R1 1.5k R2 1.5k CHARGER CONTROL BLOCK TO MCU 1 SCL TO MCU 17 SDA 12 TO MCU/NC 5 DIG_IO1 13 TO MCU/NC 3 DIG_IO2 TO MCU/NC 2 DIG_IO3 14 ISO_B1 TO ISO_B3 BAT_SNS VDDIO 4 CONNECT CLOSE TO BATTERY + THR 18 R4 10k TO MCU VLED 16 SYS_EN 15 ILED C2 22F R5 NTC 10k (OPTIONAL) GRM31CR60J22ME19 AGND 10806-040 20 C1 - 10nF 16V/X7R 0402 CBP Figure 40. Reference Circuit Diagram ISO_Bx PGND C2 - 22F 16V/X5R 1206 ISO_Sx PGND VINx C3 - 22F 16V/X5R 1206 10806-100 C4 - 10F 25V/X5R 0805 PGND Figure 41. Reference PCB Floor Plan Rev. B | Page 38 of 44 Data Sheet ADP5062 POWER DISSIPATION AND THERMAL CONSIDERATIONS CHARGER POWER DISSIPATION When the ADP5062 charger operates at high ambient temperatures and at maximum current charging and loading conditions, the junction temperature can reach the maximum allowable operating limit of 125C. When the junction temperature exceeds 140C, the ADP5062 turns off, allowing the device to cool down. When the die temperature falls below 110C and the TSD 140C fault bit in Register 0x0D is cleared by an I2C write, the ADP5062 resumes normal operation. This section provides guidelines to calculate the power dissipated in the device to ensure that the ADP5062 operates below the maximum allowable junction temperature. To determine the available output current in different operating modes under various operating conditions, use the following equations: PD = PLDOFET + PISOFET (1) where: PLDOFET is the power dissipated in the input LDO FET. PISOFET is the power dissipated in the battery isolation FET. Calculate the power dissipation in the LDO FET and the battery isolation FET using Equation 2 and Equation 3. PLDOFET = (VIN - VISO_Sx) x (ICHG + ILOAD) (2) PISOFET = (VISO_Sx - VISO_Bx) x ICHG (3) where: VIN is the input voltage at the VINx pins. VISO_Sx is the system voltage at the ISO_Sx pins. VISO_Bx is the battery voltage at the ISO_Bx pins. ICHG is the battery charge current. ILOAD is the system load current from the ISO_Sx pins. is higher and the power dissipation must be calculated using Equation 3. When the battery voltage level reaches VISO_SFC, the power dissipation can be calculated using Equation 4. PISOFET = RDSON_ISO x ICHG (4) where: RDSON_ISO is the on resistance of the battery isolation FET (typically 110 m during charging). ICHG is the battery charge current. The thermal control loop of the ADP5062 automatically limits the charge current to maintain a die temperature below TLIM (typically 115C). The most intuitive and practical way to calculate the power dissipation in the ADP5062 device is to measure the power dissipated at the input and all of the outputs. Perform the measurements at the worst case conditions (voltages, currents, and temperature). The difference between input and output power is the power that is dissipated in the device. JUNCTION TEMPERATURE In cases where the board temperature, TA, is known, the thermal resistance parameter, JA, can be used to estimate the junction temperature rise. TJ is calculated from TA and PD using the formula TJ = TA + (PD x JA) (5) The typical JA value for the 20-lead LFCSP is 35.6C/W (see Table 5). A very important factor to consider is that JA is based on a 4-layer, 4 in x 3 in, 2.5 oz. copper board as per JEDEC standard, and real-world applications may use different sizes and layers. It is important to maximize the copper to remove the heat from the device. Copper exposed to air dissipates heat better than copper used in the inner layers. If the case temperature can be measured, the junction temperature is calculated by LDO Mode The system regulation voltage is user-programmable from 4.3 V to 5.0 V. In LDO mode (charging disabled, EN_CHG = low), calculation of the total power dissipation is simplified, assuming that all current is drawn from the VINx pins and the battery is not shared with ISO_Sx. PD = (VIN - VISO_Sx) x ILOAD Charging Mode In charging mode, the voltage at the ISO_Sx pins depends on the battery level. When the battery voltage is lower than VISO_SFC (typically 3.8 V), the voltage drop over the battery isolation FET TJ = TC + (PD x JC) (6) where TC is the case temperature and JC is the junction-to-case thermal resistance provided in Table 5. The reliable operation of the charger can be achieved only if the estimated die junction temperature of the ADP5062 (Equation 5) is less than 125C. Reliability and mean time between failures (MTBF) are greatly affected by increasing the junction temperature. Additional information about product reliability can be found in the ADI Reliability Handbook located at the following URL: www.analog.com/reliability_handbook. Rev. B | Page 39 of 44 ADP5062 Data Sheet FACTORY-PROGRAMMABLE OPTIONS CHARGER OPTIONS Table 37 to Table 49 list the factory-programmable options of the ADP5062. In each of these tables, the selection column represents the default setting of Model ADP5062ACPZ-1-R7 and Model ADP5062ACPZ-2-R7. Table 37. Default Termination Voltage Option 000 = 4.20 V 010 = 3.70 V 011 = 3.80 V 100 = 3.90 V 101 = 4.00 V 110 = 4.10 V 111 = 4.40 V Selection 000 = 4.20 V Table 38. Default Fast Charge Current Option 000 = 500 mA 001 = 300 mA 010 = 550 mA 011 = 600 mA 100 = 750 mA 101 = 900 mA 110 = 1300 mA 111 = 1300 mA Selection 100 = 750 mA Selection 000 = 52.5 mA Selection 000 = 4.3 V/ADP5062ACPZ-2-R7 111 = 5.0 V/ADP5062ACPZ-1-R7 Table 42. Thermistor Resistance Selection 0 = 10 k Table 43. Thermistor Beta Value Option 0100 = 3150 0101 = 3350 0110 = 3500 0111 = 3650 1000 = 3850 1001 = 4000 1010 = 4200 1011 = 4400 Selection 0100 = 3150 Table 44. DIS_IC1 Mode Select Table 40. Default Trickle to Fast Charge Threshold Option 00 = 2.5 V 01 = 2.0 V 10 = 2.9 V 11 = 2.6 V Option 000 = 4.3 V 001 = 4.4 V 010 = 4.5 V 011 = 4.6 V 100 = 4.7 V 101 = 4.8 V 110 = 4.9 V 111 = 5.0 V Option 0 = 10 k 1 = 100 k Table 39. Default End of Charge Current Option 000 = 52.5 mA 001 = 72.5 mA 010 = 12.5 mA 011 = 32.5 mA 100 = 142.5 mA 101 = 167.5 mA 110 = 92.5 mA 111 = 117.5 mA Table 41. Default System Voltage Selection 00 = 2.5 V Option 0 = DIC_IC1 mode select, VINx current = 280 A, ISO_Bx can float, no leak to ISO_Bx 1 = DIC_IC1 mode select, VINx current = 110 A, supply switch leaks from VINx to ISO_Bx Selection 0 Table 45. Trickle or Fast Charge Timer Fault Operation Option 0 = after timeout LDO off, charging off 1 = after timeout LDO mode active, charging off Rev. B | Page 40 of 44 Selection 1 = LDO mode active Data Sheet ADP5062 I2C REGISTER DEFAULTS Table 46. I2C Register Default Settings Bit Name CHG_VLIM[1:0] I2C Register Address, Bit Location Address 0x03, Bits[1:0] DIS_RCH Address 0x05, Bit 7 EN_WD Address 0x06, Bit 2 DIS_IC1 Address 0x07, Bit 6 EN_CHG Address 0x07, Bit 0 EN_JEITA Address 0x08, Bit 7 JEITA_SELECT Address 0x08, Bit 6 EN_CHG_VLIM Address 0x08, Bit 5 IDEAL_DIODE[1:0] Address 0x08, Bits[4:3] Option 0 = limit 3.2 V 1 = limit 3.7 V 0 = recharge enabled 1 = recharge disabled 0 = watchdog disabled 1 = watchdog enabled 0 = not activated 1 = activated 0 = charging disabled 1 = charging enabled 0 = JEITA disabled 1 = JEITA enabled 0 = JEITA1 charging 1= JEITA2 charging 0 = limit disabled 1 = limit enabled 00 = ideal diode operates when VISO_Sx < VISO_Bx 01 = ideal diode operates when VISO_Sx < VISO_Bx and VBAT_SNS > VWEAK 10 = ideal diode is disabled 11 = ideal diode is disabled Selection 0 = limit 3.2 V 0 = recharge enabled 0 = disabled 0 = not activated 0 = charging disabled 0 = JEITA disabled 0 = JEITA1 charging 0 = limit disabled 00 = VISO_Sx < VISO_Bx DIGITAL INPUT AND OUTPUT OPTIONS Table 47. I2C Address 0x11, Bits[1:0] SYS_EN Output Default Option 00 = SYS_EN is activated when LDO is active and system voltage is available 01 = SYS_EN is activated by ISO_Bx voltage; battery charging mode 10 = SYS_EN is activated and the isolation FET is disabled when the battery drops below VWEAK 1 11 = SYS_EN is active in LDO mode when the charger is disabled. SYS_EN is active in charging mode when VISO_Bx VWEAK 1 This option is active when VINx = 0 V and the battery monitor is activated from Register 0x07, Bit D5 (EN_BMON). Rev. B | Page 41 of 44 Selection (Default) 00 ADP5062 Data Sheet DIG_IO1, DIG_IO2, and DIG_IO3 Options Table 48. DIG_IO1 Polarity Option 0 = DIG_IO1 polarity, high active operation 1 = DIG_IO1 polarity, low active operation Selection 0 = high active Table 49. DIG_IOx Options Option 0000 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 DIG_IO1 Function IVINx limit Low = 100 mA High = 500 mA IVINx limit Low = 100 mA High= 500 mA IVINx limit Low = 100 mA High= 500 mA IVINx limit Low = 100 mA High= 500 mA IVINx limit Low = 100 mA High= 500 mA IVINx limit Low = 100 mA High= 500 mA Charging Low = charging disabled High = charging enabled IVINx limit Low = 100 mA High= 500 mA IVINx limit Low = 100 mA High= 500 mA IVINx limit Low = 100 mA High= 500 mA IVINx limit Low = 100 mA High= 500 mA IVINx limit Low = 100 mA High= 500 mA IVINx limit Low = 100 mA High= 500 mA IVINx limit N/A High = IVINx limit 1500 mA Disable IC1 Low = not activated High = activated DIG_IO2 Function Disable IC1 Low = not activated High = activated IVINx limit N/A High = IVINx limit 1500 mA IVINx limit N/A High = IVINx limit 1500 mA IVINx limit N/A High = IVIN limit 1500 mA IVINx limit N/A High = IVINx limit 1500 mA Recharge N/A High = disable recharge Disable IC1 Low = not activated High = activated IVINx limit N/A High = IVINx limit 1500 mA Charging Low = charging disabled High = charging enabled Disable IC1 Low = not activated High = activated Recharge N/A High = disable recharge Fast charge current Low = ICHG High = ICHG[4:0] / 2 LDO Low = LDO active High = LDO disabled Charging Low = charging disabled High = charging enabled Charging Low = charging disabled High = charging enabled DIG_IO3 Function Charging disable/enable Low = charging disable High = charging enabled Disable IC1 Low = not activated High = activated Fast charge current Low = ICHG[4:0] High = ICHG[4:0] / 2 LDO Low = LDO active High = LDO disabled Charging Low = charging disabled High = charging enabled Charging Low = charging disabled High = charging enabled Recharge N/A High = disable recharge Interrupt output N/A N/A Interrupt output N/A N/A Interrupt output N/A N/A Interrupt output N/A N/A Interrupt output N/A N/A Interrupt output N/A N/A Interrupt output N/A N/A Interrupt output N/A N/A Rev. B | Page 42 of 44 Selection 0000 Data Sheet ADP5062 PACKAGING AND ORDERING INFORMATION OUTLINE DIMENSIONS 0.30 0.25 0.18 0.50 BSC PIN 1 INDICATOR 20 16 15 1 EXPOSED PAD 2.75 2.60 SQ 2.35 11 TOP VIEW 0.80 0.75 0.70 SEATING PLANE 0.50 0.40 0.30 5 10 6 0.25 MIN BOTTOM VIEW 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-WGGD. 020509-B PIN 1 INDICATOR 4.10 4.00 SQ 3.90 Figure 42. 20-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 4 mm x 4 mm Body, Very Very Thin Quad (CP-20-8) Dimensions shown in millimeters ORDERING GUIDE Model1, 2 ADP5062ACPZ-1-R7 ADP5062ACPZ-2-R7 ADP5062CP-EVALZ 1 2 Temperature Range (Junction) -40C to +125C -40C to +125C Package Description 20-Lead LFCSP_WQ 20-Lead LFCSP_WQ ADP5062 Evaluation Board Z = RoHS Compliant Part. For additional factory-programmable options, contact an Analog Devices local sales or distribution representative. Rev. B | Page 43 of 44 Package Option CP-20-8 CP-20-8 ADP5062 Data Sheet NOTES I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors). (c)2012-2013 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D10806-0-10/13(B) Rev. B | Page 44 of 44 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: ADP5062ACPZ-1-R7 ADP5062CP-EVALZ ADP5062ACPZ-2-R7