WM7121PE Top Port Analog Silicon Microphone DESCRIPTION FEATURES The WM7121P is a low-profile silicon analog microphone. It offers high Signal to Noise Ratio (SNR) and low power consumption and is suited to a wide variety of consumer applications. High SNR (65dB) Low variation in sensitivity (1dB tolerance) Matched pair with Bottom Port microphone WM7132P The WM7121P incorporates Cirrus proprietary CMOS/MEMS membrane technology, offering high reliability and high performance in a miniature, low-profile package. The WM7121P is designed to withstand the high temperatures associated with automated flow solder assembly processes. (Note that conventional microphones can be damaged by this process.) Low current consumption (190A) Analog output Top Port LGA Package 1.5V to 3.7V supply The WM7121P Top Port microphone offers matched performance to the WM7132P Bottom Port microphone. The matched characteristics enable highly accurate sound pickup in opposite directions, suitable for noise cancellation and other DSP algorithms. The WM7121P offers tight tolerance on the microphone sensitivity, giving reduced variation between parts. This removes the need for in-line production calibration of partto-part microphone variations. BLOCK DIAGRAM - Matched sensitivity, roll-off, and phase response APPLICATIONS Mobile phone handsets Portable media players Digital still cameras Digital video cameras Bluetooth headsets Portable navigation devices Portable games consoles 3D VIEW VDD WM7121P CHARGE PUMP AMP OUTPUT CMOS MEMS Transducer 3.76mm x 2.95mm x 1.10mm LGA package GND http://www.cirrus.com Copyright Cirrus Logic, Inc., 2014-2015 (All Rights Reserved) Rev 4.0 MAR `15 WM7121PE TABLE OF CONTENTS DESCRIPTION ................................................................................................................ 1 FEATURES ..................................................................................................................... 1 APPLICATIONS ............................................................................................................. 1 BLOCK DIAGRAM ......................................................................................................... 1 3D VIEW ......................................................................................................................... 1 TABLE OF CONTENTS.................................................................................................. 2 PIN CONFIGURATION ................................................................................................... 3 PIN DESCRIPTION ......................................................................................................... 3 ORDERING INFORMATION ........................................................................................... 3 ABSOLUTE MAXIMUM RATINGS ................................................................................. 4 IMPORTANT ASSEMBLY GUIDELINES ....................................................................... 4 RECOMMENDED OPERATING CONDITIONS .............................................................. 4 ACOUSTIC AND ELECTRICAL CHARACTERISTICS .................................................. 5 TERMINOLOGY ......................................................................................................................... 5 TYPICAL PERFORMANCE ............................................................................................ 6 APPLICATIONS INFORMATION ................................................................................... 7 RECOMMENDED EXTERNAL COMPONENTS ........................................................................ 7 OPTIMISED SYSTEM RF DESIGN ........................................................................................... 7 CONNECTION TO A CIRRUS CODEC ..................................................................................... 8 MATCHED MICROPHONE PAIRS ............................................................................................ 8 PCB LAND PATTERN AND PASTE STENCIL .......................................................................... 9 PACKAGE DIMENSIONS ............................................................................................. 10 IMPORTANT NOTICE .................................................................................................. 11 REVISION HISTORY .................................................................................................... 12 2 Rev 4.0 WM7121PE PIN CONFIGURATION 4 1 3 2 Top View PIN DESCRIPTION PIN NAME TYPE 1 VDD Supply Analog Supply DESCRIPTION 2 GND Supply Analog ground 3 GND Supply Analog ground 4 OUTPUT Analogue Output Microphone analog output signal ORDERING INFORMATION ORDER CODE TEMPERATURE RANGE PACKAGE MOISTURE SENSITIVITY LEVEL PEAK SOLDERING TEMPERATURE WM7121PIMSE/RV -40 to +100C LGA (tape and reel) MSL2A +260C Note: Reel quantity = 5000 All devices are Pb-free and Halogen free. Rev 4.0 3 WM7121PE ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified. ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible to damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage of this device. Cirrus tests its package types according to IPC/JEDEC J-STD-020 for Moisture Sensitivity to determine acceptable storage conditions prior to surface mount assembly. These levels are: MSL1 = unlimited floor life at <30C / 85% Relative Humidity. Not normally stored in moisture barrier bag. MSL2 = out of bag storage for 1 year at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. MSL2A = out of bag storage for 4 weeks at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. MSL3 = out of bag storage for 168 hours at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. The Moisture Sensitivity Level for each package type is specified in Ordering Information. CONDITION MIN MAX Supply Voltage (VDD) -0.3V +4.2V Operating temperature range, TA -40C +100C Storage temperature prior to soldering 30C max / 60% RH max Storage temperature after soldering -40C +100C IMPORTANT ASSEMBLY GUIDELINES Do not put a vacuum over the port hole of the microphone. Placing a vacuum over the port hole can damage the device. Do not board wash the microphone after a re-flow process. Board washing and the associated cleaning agents can damage the device. Do not expose to ultrasonic cleaning methods. Do not use a vapour phase re-flow process. The vapour can damage the device. Please refer to application note WAN0273 (MEMS MIC Assembly and Handling Guidelines) for further assembly and handling guidelines. RECOMMENDED OPERATING CONDITIONS PARAMETER 4 SYMBOL MIN Analog Supply Range VDD 1.5 Ground GND TYP 0 MAX UNIT 3.7 V V Rev 4.0 WM7121PE ACOUSTIC AND ELECTRICAL CHARACTERISTICS Test Conditions: VDD=2.1V, 1kHz test signal, TA = 25C, unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN Directivity Polarity Sensitivity Positive sound pressure S Acoustic Overload Total Harmonic Distortion Signal to Noise Ratio Dynamic Range TYP MAX UNIT Omni-directional THD 94dB SPL Positive output voltage -39 -38 No Load, THD < 10% 126 100dB SPL 0.1 114dB SPL 0.2 -37 dBV dB SPL 1 % 122dB SPL 1 SNR A-weighted 65 dB DR A-weighted 93 dB -3dB low frequency 62 Hz Frequency Response +3dB high frequency Frequency Response Flatness 200Hz to 6kHz Acoustic Noise Floor Electrical Noise Floor 15000 -1 +1 dB A-weighted 29 dB SPL A-weighted -103 dBV PSRR 217Hz sine wave, 100mV (peak-peak) 46 dB Power Supply Rejection PSR 217Hz square wave, 100mV (peak-peak) -72 dBV Current Consumption IVDD 190 240 A Output DC Impedance ZOUT 55 150 Power Supply Rejection Ratio TERMINOLOGY 1. 2. 3. 4. 5. Sensitivity (dBV) - Sensitivity is a measure of the microphone output response to the acoustic pressure of a 1kHz 94dB SPL (1Pa RMS) sine wave. Total Harmonic Distortion (%) - THD is the ratio of the RMS sum of the harmonic distortion products in the specified bandwidth (see note below) relative to the amplitude of the fundamental (ie. test frequency) output. Signal-to-Noise Ratio (dB) - SNR is a measure of the difference in level between the output response of a 1kHz 94dB SPL sine wave and the idle noise output. Dynamic Range (dB) - DR is the ratio of the 1% THD microphone output level (in response to a sine wave input) and the idle noise output level. All performance measurements are carried out within a 20Hz to 20kHz bandwidth and, where noted, an A-weighted filter. Failure to use these filters will result in higher THD and lower SNR values than are found in the Acoustic and Electrical Characteristics. The low pass filter removes out of band noise. Rev 4.0 5 WM7121PE TYPICAL PERFORMANCE Sensitivity vs. Frequency PSRR vs. Frequency Sensitivity vs. Supply Voltage Current Consumption vs. Supply Voltage THD vs. Sound Pressure Level 6 Rev 4.0 WM7121PE APPLICATIONS INFORMATION RECOMMENDED EXTERNAL COMPONENTS WM7121P VDD C + OUTPUT 1F R GND Figure 1 WM7121P Recommended External Components A DC-blocking output capacitor is required on the OUTPUT pin, as illustrated in Figure 1. A single capacitor is required for a single-ended connection. The capacitor must be correctly selected as it affects the cut-off frequency of the output path. A low cut-off frequency is desirable as it means there is no significant filtering of the audio bandwidth. The 3dB cut-off frequency of the output path is given by the equation below, where C is the output capacitance and R is the input resistance of the other circuit. 3dB filter roll-off frequency = 1 2 p RC A typical recommended configuration, with 1uF DC-blocking capacitor and 20k minimum input circuit impedance, gives a 3dB cut-off frequency of 10Hz or less. Tantalum electrolytic capacitors are particularly suitable for the DC-blocking components as they offer high stability in a small package size. OPTIMISED SYSTEM RF DESIGN For optimised RF design please refer to document WAN0278 (Recommended PCB Layout for Microphone RF Immunity in Mobile Cell Phone Applications) for further information. Rev 4.0 7 WM7121PE CONNECTION TO A CIRRUS CODEC Cirrus provides a range of audio CODECs incorporating an analog microphone input interface; these support connection to silicon microphones such as the WM7121P. The recommended connection of a WM7121P silicon microphone is illustrated in Figure 2 (for singleended mode) and Figure 3 (for pseudo-differential mode). A DC blocking capacitor is required, as described in the previous section. A 2.2F decoupling capacitor is also recommended; this should be positioned close to the VDD pin of the WM7121P. Further information on Cirrus audio CODECs is provided in the respective product datasheet, which is available from the Cirrus website. 2.2F WM7121P VDD Audio CODEC MICBIAS OUTPUT 1F Analogue Input pin (eg. IN1xP) GND Figure 2 WM7121P Silicon Microphone Single-ended Connection 2.2F WM7121P VDD Audio CODEC MICBIAS OUTPUT GND 1F Non-Inverting Input pin (eg. IN1xP) 1F Inverting Input pin (eg. IN1xN) Figure 3 WM7121P Silicon Microphone Pseudo-differential Connection MATCHED MICROPHONE PAIRS The WM7121P Top Port microphone offers matched performance to the WM7132P Bottom Port microphone. Matched microphone pairs are ideal for accurate sound pick-up from opposite directions in slim, lowprofile applications. For best acoustic matching, the Top Port and Bottom Port microphones should be positioned close together, on the same side of the PCB. The WM7121P and WM7132P microphones offer matched sensitivity, low-frequency roll-off, and phase response characteristics, enabling simplified system design when using these complementary devices. 8 Rev 4.0 WM7121PE PCB LAND PATTERN AND PASTE STENCIL The recommended PCB Land Pattern and Paste Stencil Pattern for the WM7121P microphone are shown in Figure 4 and Figure 5. See also Application Note WAN0284 (General Design Considerations for MEMS Microphones) for further details of PCB footprint design. Full definition of the package dimensions is provided in the "Package Dimensions" section. Figure 4 DM124 - PCB Land Pattern, Top View Figure 5 DM124 - Paste Stenctil Pattern, Top View Rev 4.0 9 WM7121PE PACKAGE DIMENSIONS 10 Rev 4.0 WM7121PE IMPORTANT NOTICE Contacting Cirrus Logic Support For all product questions and inquiries, contact a Cirrus Logic Sales Representative. To find one nearest you, go to www.cirrus.com. The products and services of Cirrus Logic International (UK) Limited; Cirrus Logic, Inc.; and other companies in the Cirrus Logic group (collectively either "Cirrus" or "Cirrus Logic") are sold subject to Cirrus's terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, indemnification, and limitation of liability. Software is provided pursuant to applicable license terms. Cirrus reserves the right to make changes to its products and specifications or to discontinue any product or service without notice. Customers should therefore obtain the latest version of relevant information from Cirrus to verify that the information is current and complete. Testing and other quality control techniques are utilized to the extent Cirrus deems necessary. Specific testing of all parameters of each device is not necessarily performed. In order to minimize risks associated with customer applications, the customer must use adequate design and operating safeguards to minimize inherent or procedural hazards. Cirrus is not liable for applications assistance or customer product design. The customer is solely responsible for its selection and use of Cirrus products. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, NUCLEAR SYSTEMS, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied, under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Any provision or publication of any third party's products or services does not constitute Cirrus's approval, license, warranty or endorsement thereof. Cirrus gives consent for copies to be made of the information contained herein only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus, and only if the reproduction is without alteration and is accompanied by all associated copyright, proprietary and other notices and conditions (including this notice). This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. This document and its information is provided "AS IS" without warranty of any kind (express or implied). All statutory warranties and conditions are excluded to the fullest extent possible. No responsibility is assumed by Cirrus for the use of information herein, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. Cirrus Logic, Cirrus, the Cirrus Logic logo design and SoundClear are among the trademarks of Cirrus. Other brand and product names may be trademarks or service marks of their respective owners. Copyright (c) 2014-2015 Cirrus Logic, Inc. All rights reserved. Rev 4.0 11 WM7121PE REVISION HISTORY DATE REV 26/02/14 1.0 First Release 25/03/14 2.0 Formatting and miscellaneous updates throughout document Electrical Characteristics updated Package Outline Drawing updated 1-9 5 10 PH 13/06/14 3.0 Electrical Characteristics updated Typical Performance graphs added PCB Stencil drawings updated Package Outline Drawing updated 5 6 9 10 PH 05/01/15 4.0 Updated to Rev 4.0 (Production) status 12 DESCRIPTION OF CHANGES PAGE CHANGED BY IS PH Rev 4.0 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Cirrus Logic: WM7121PIMS/RV