LM2904MX - Texas Instruments High-Performance Analog

LM158-N, LM258-N, LM2904-N, LM358-N

www.ti.com

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

LM158/LM258/LM358/LM2904 Low Power Dual Operational Amplifiers

Check for Samples: LM158-N,LM258-N,LM2904-N,LM358-N

1FEATURES ADVANTAGES

2• Available in 8-Bump DSBGA Chip- • Two Internally Compensated Op Amps

Sized Package, (See AN-1112 (SNVA009)) • Eliminates Need for Dual Supplies

• Internally Frequency Compensated for Unity • Allows Direct Sensing Near GND and VOUT

Gain Also Goes to GND

• Large DC Voltage Gain: 100 dB • Compatible with All Forms of Logic

• Wide Bandwidth (Unity Gain): 1 MHz • Power Drain Suitable for Battery Operation

(Temperature Compensated)

• Wide Power Supply Range: DESCRIPTION

The LM158 series consists of two independent, high

– Single Supply: 3V to 32V gain, internally frequency compensated operational

– Or Dual Supplies: ±1.5V to ±16V amplifiers which were designed specifically to operate

• Very Low Supply Current Drain (500 from a single power supply over a wide range of

μA)—Essentially Independent of Supply voltages. Operation from split power supplies is also

Voltage possible and the low power supply current drain is

independent of the magnitude of the power supply

• Low Input Offset Voltage: 2 mV voltage.

• Input Common-Mode Voltage Range Includes Application areas include transducer amplifiers, dc

Ground gain blocks and all the conventional op amp circuits

• Differential Input Voltage Range Equal to the which now can be more easily implemented in single

Power Supply Voltage power supply systems. For example, the LM158

• Large Output Voltage Swing series can be directly operated off of the standard

+5V power supply voltage which is used in digital

UNIQUE CHARACTERISTICS systems and will easily provide the required interface

electronics without requiring the additional ±15V

• In the Llinear Mode the Input Common-Mode power supplies.

Voltage Range Includes Ground and the The LM358 and LM2904 are available in a chip sized

Output Voltage Can Also Swing to Ground, package (8-Bump DSBGA) using TI's DSBGA

even though Operated from Only a Single package technology.

Power Supply Voltage.

• The Unity Gain Cross Frequency is

Temperature Compensated.

• The Input Bias Current is also Temperature

Compensated.

1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2All trademarks are the property of their respective owners.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

LM158-N, LM258-N, LM2904-N, LM358-N

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

www.ti.com

Voltage Controlled Oscillator (VCO)

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

www.ti.com

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

ABSOLUTE MAXIMUM RATINGS(1)(2)

LM158/LM258/LM358 LM2904

LM158A/LM258A/LM3

58A

Supply Voltage, V+32V 26V

Differential Input Voltage 32V 26V

Input Voltage −0.3V to +32V −0.3V to +26V

Power Dissipation(3)

PDIP (P) 830 mW 830 mW

TO-99 (LMC) 550 mW

SOIC (D) 530 mW 530 mW

DSBGA (YPB) 435mW

Output Short-Circuit to GND (One V+≤15V and TA= 25°C Continuous Continuous

Amplifier)(4)

Input Current (VIN <−0.3V)(5) 50 mA 50 mA

Operating Temperature Range

LM358 0°C to +70°C −40°C to +85°C

LM258 −25°C to +85°C

LM158 −55°C to +125°C

Storage Temperature Range −65°C to +150°C −65°C to +150°C

Lead Temperature, PDIP (P)

(Soldering, 10 seconds) 260°C 260°C

Lead Temperature, TO-99 (LMC)

(Soldering, 10 seconds) 300°C 300°C

Soldering Information

PDIP Package (P)

Soldering (10 seconds) 260°C 260°C

SOIC Package (D)

Vapor Phase (60 seconds) 215°C 215°C

Infrared (15 seconds) 220°C 220°C

ESD Tolerance(6) 250V 250V

(1) Refer to RETS158AX for LM158A military specifications and to RETS158X for LM158 military specifications.

(2) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.

(3) For operating at high temperatures, the LM358/LM358A, LM2904 must be derated based on a +125°C maximum junction temperature

and a thermal resistance of 120°C/W for PDIP, 182°C/W for TO-99, 189°C/W for SOIC package, and 230°C/W for DSBGA, which

applies for the device soldered in a printed circuit board, operating in a still air ambient. The LM258/LM258A and LM158/LM158A can be

derated based on a +150°C maximum junction temperature. The dissipation is the total of both amplifiers—use external resistors, where

possible, to allow the amplifier to saturate or to reduce the power which is dissipated in the integrated circuit.

(4) Short circuits from the output to V+can cause excessive heating and eventual destruction. When considering short circuits to ground,

the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,

continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result

from simultaneous shorts on all amplifiers.

(5) This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of

the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is

also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the op amps to go to

the V+voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and

normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.3V (at 25°C).

(6) Human body model, 1.5 kΩin series with 100 pF.

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

www.ti.com

ELECTRICAL CHARACTERISTICS

V+= +5.0V, unless otherwise stated

Parameter Conditions LM158A LM358A LM158/LM258 Units

Min Typ Max Min Typ Max Min Typ Max

Input Offset Voltage (1), TA= 25°C 1 2 2 3 2 5 mV

Input Bias Current IIN(+) or IIN(−), TA= 25°C, 20 50 45 100 45 150 nA

VCM = 0V,(2)

Input Offset Current IIN(+) −IIN(−), VCM = 0V, TA= 25°C 2 10 5 30 3 30 nA

Input Common-Mode V+= 30V,(3) 0 V+−1.5 0 V+−1.5 0 V+−1.5 V

Voltage Range (LM2904, V+= 26V), TA= 25°C

Supply Current Over Full Temperature Range

RL=∞on All Op Amps

V+= 30V (LM2904 V+= 26V) 1 2 1 2 1 2 mA

V+= 5V 0.5 1.2 0.5 1.2 0.5 1.2 mA

(1) VO≃1.4V, RS= 0Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+−1.5V) at 25°C. For LM2904, V+from

5V to 26V.

(2) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the

state of the output so no loading change exists on the input lines.

(3) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The

upper end of the common-mode voltage range is V+−1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V for

LM2904), independent of the magnitude of V+.

ELECTRICAL CHARACTERISTICS

V+= +5.0V, unless otherwise stated

Parameter Conditions LM358 LM2904 Units

Min Typ Max Min Typ Max

Input Offset Voltage See(1) , TA= 25°C 2 7 2 7 mV

Input Bias Current IIN(+) or IIN(−), TA= 25°C, 45 250 45 250 nA

VCM = 0V, See(2)

Input Offset Current IIN(+) −IIN(−), VCM = 0V, TA= 25°C 5 50 5 50 nA

Input Common-Mode V+= 30V, See(3) V+−1. V+−1.

0 0 V

Voltage Range (LM2904, V+= 26V), TA= 25°C 5 5

Supply Current Over Full Temperature Range

RL=∞on All Op Amps

V+= 30V (LM2904 V+= 26V) 1 2 1 2 mA

V+= 5V 0.5 1.2 0.5 1.2 mA

(1) VO≃1.4V, RS= 0Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+−1.5V) at 25°C. For LM2904, V+from

5V to 26V.

(2) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the

state of the output so no loading change exists on the input lines.

(3) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The

upper end of the common-mode voltage range is V+−1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V for

LM2904), independent of the magnitude of V+.

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

www.ti.com

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

ELECTRICAL CHARACTERISTICS

V+= +5.0V, See(1), unless otherwise stated LM158A LM358A LM158/LM258 Units

Parameter Conditions Min Typ Max Min Typ Max Min Typ Max

Large Signal Voltage V+= 15V, TA= 25°C, 50 100 25 100 50 100 V/mV

Gain RL≥2 kΩ, (For VO= 1V to 11V)

Common-Mode TA= 25°C, 70 85 65 85 70 85 dB

Rejection Ratio VCM = 0V to V+−1.5V

Power Supply V+= 5V to 30V 65 100 65 100 65 100 dB

Rejection Ratio (LM2904, V+= 5V to 26V), TA= 25°C

Amplifier-to-Amplifier f = 1 kHz to 20 kHz, TA= 25°C (Input −120 −120 −120 dB

Coupling Referred), See(2)

Output Current Source VIN+= 1V,

VIN−= 0V, 20 40 20 40 20 40 mA

V+= 15V,

VO= 2V, TA= 25°C

Sink VIN−= 1V, VIN+= 0V

V+= 15V, TA= 25°C, 10 20 10 20 10 20 mA

VO= 2V

VIN−= 1V,

VIN+= 0V 12 50 12 50 12 50 μA

TA= 25°C, VO= 200 mV,

V+= 15V

Short Circuit to Ground TA= 25°C, See(3), V+= 15V 40 60 40 60 40 60 mA

Input Offset Voltage See(4) 4 5 7 mV

Input Offset Voltage Drift RS= 0Ω7 15 7 20 7 μV/°C

Input Offset Current IIN(+) −IIN(−)30 75 100 nA

Input Offset Current Drift RS= 0Ω10 200 10 300 10 pA/°C

Input Bias Current IIN(+) or IIN(−)40 100 40 200 40 300 nA

Input Common-Mode V+= 30 V, See(5) (LM2904, V+= 26V) 0 V+−2 0 V+−2 0 V+−2 V

Voltage Range

Large Signal Voltage V+= +15V

Gain (VO= 1V to 11V) 25 15 25 V/mV

RL≥2 kΩ

Output VOH V+= +30V RL= 2 kΩ26 26 26 V

Voltage (LM2904, V+= 26V) RL= 10 kΩ27 28 27 28 27 28 V

Swing VOL V+= 5V, RL= 10 kΩ5 20 5 20 5 20 mV

(1) These specifications are limited to −55°C ≤TA≤+125°C for the LM158/LM158A. With the LM258/LM258A, all temperature

specifications are limited to −25°C ≤TA≤+85°C, the LM358/LM358A temperature specifications are limited to 0°C ≤TA≤+70°C, and

the LM2904 specifications are limited to −40°C ≤TA≤+85°C.

(2) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This

typically can be detected as this type of capacitance increases at higher frequencies.

(3) Short circuits from the output to V+can cause excessive heating and eventual destruction. When considering short circuits to ground,

the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,

continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result

from simultaneous shorts on all amplifiers.

(4) VO≃1.4V, RS= 0Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+−1.5V) at 25°C. For LM2904, V+from

5V to 26V.

(5) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The

upper end of the common-mode voltage range is V+−1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V for

LM2904), independent of the magnitude of V+.

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

www.ti.com

ELECTRICAL CHARACTERISTICS (continued)

V+= +5.0V, See(1), unless otherwise stated LM158A LM358A LM158/LM258 Units

Parameter Conditions Min Typ Max Min Typ Max Min Typ Max

Output Current Source VIN+= +1V, VIN−= 0V, 10 20 10 20 10 20 mA

V+= 15V, VO= 2V

Sink VIN−= +1V, VIN+= 0V, 10 15 5 8 5 8 mA

V+= 15V, VO= 2V

ELECTRICAL CHARACTERISTICS

V+= +5.0V, See(1), unless otherwise stated LM358 LM2904 Units

Parameter Conditions Min Typ Max Min Typ Max

Large Signal Voltage V+= 15V, TA= 25°C,

Gain RL≥2 kΩ, (For VO= 1V to 11V) 25 100 25 100 V/mV

Common-Mode TA= 25°C, 65 85 50 70 dB

Rejection Ratio VCM = 0V to V+−1.5V

Power Supply V+= 5V to 30V 65 100 50 100 dB

Rejection Ratio (LM2904, V+= 5V to 26V), TA= 25°C

Amplifier-to-Amplifier Coupling f = 1 kHz to 20 kHz, TA= 25°C −120 −120 dB

(Input Referred), See(2)

Output Current Source VIN+= 1V,

VIN−= 0V, 20 40 20 40 mA

V+= 15V,

VO= 2V, TA= 25°C

Sink VIN−= 1V, VIN+= 0V

V+= 15V, TA= 25°C, 10 20 10 20 mA

VO= 2V

VIN−= 1V,

VIN+= 0V 12 50 12 50 μA

TA= 25°C, VO= 200 mV,

V+= 15V

Short Circuit to Ground TA= 25°C, See(3), V+= 15V 40 60 40 60 mA

Input Offset Voltage See(4) 9 10 mV

Input Offset Voltage Drift RS= 0Ω7 7 μV/°C

Input Offset Current IIN(+) −IIN(−)150 45 200 nA

Input Offset Current Drift RS= 0Ω10 10 pA/°C

Input Bias Current IIN(+) or IIN(−)40 500 40 500 nA

Input Common-Mode V+= 30 V, See(5) (LM2904, V+= 26V) 0 V+−2 0 V+−2 V

Voltage Range

(1) These specifications are limited to −55°C ≤TA≤+125°C for the LM158/LM158A. With the LM258/LM258A, all temperature

specifications are limited to −25°C ≤TA≤+85°C, the LM358/LM358A temperature specifications are limited to 0°C ≤TA≤+70°C, and

the LM2904 specifications are limited to −40°C ≤TA≤+85°C.

(2) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This

typically can be detected as this type of capacitance increases at higher frequencies.

(3) Short circuits from the output to V+can cause excessive heating and eventual destruction. When considering short circuits to ground,

the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,

continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result

from simultaneous shorts on all amplifiers.

(4) VO≃1.4V, RS= 0Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+−1.5V) at 25°C. For LM2904, V+from

5V to 26V.

(5) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The

upper end of the common-mode voltage range is V+−1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V for

LM2904), independent of the magnitude of V+.

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

www.ti.com

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

ELECTRICAL CHARACTERISTICS (continued)

V+= +5.0V, See(1), unless otherwise stated LM358 LM2904 Units

Parameter Conditions Min Typ Max Min Typ Max

Large Signal Voltage Gain V+= +15V

(VO= 1V to 11V) 15 15 V/mV

RL≥2 kΩ

Output VOH V+= +30V RL= 2 kΩ26 22 V

Voltage (LM2904, V+= 26V) RL= 10 kΩ27 28 23 24 V

Swing VOL V+= 5V, RL= 10 kΩ5 20 5 100 mV

Output Current Source VIN+= +1V, VIN−= 0V, 10 20 10 20 mA

V+= 15V, VO= 2V

Sink VIN−= +1V, VIN+= 0V, 5 8 5 8 mA

V+= 15V, VO= 2V

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

www.ti.com

TYPICAL PERFORMANCE CHARACTERISTICS

Input Voltage Range Input Current

Figure 1. Figure 2.

Supply Current Voltage Gain

Figure 3. Figure 4.

Open Loop Frequency Response Common-Mode Rejection Ratio

Figure 5. Figure 6.

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

www.ti.com

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

TYPICAL PERFORMANCE CHARACTERISTICS (continued)

Voltage Follower Pulse Response Voltage Follower Pulse Response (Small Signal)

Figure 7. Figure 8.

Large Signal Frequency Response Output Characteristics Current Sourcing

Figure 9. Figure 10.

Output Characteristics Current Sinking Current Limiting

Figure 11. Figure 12.

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

www.ti.com

TYPICAL PERFORMANCE CHARACTERISTICS (continued)

Input Current (LM2902 only) Voltage Gain (LM2902 only)

Figure 13. Figure 14.

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

www.ti.com

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

APPLICATION HINTS

The LM158 series are op amps which operate with only a single power supply voltage, have true-differential

inputs, and remain in the linear mode with an input common-mode voltage of 0 VDC. These amplifiers operate

over a wide range of power supply voltage with little change in performance characteristics. At 25°C amplifier

operation is possible down to a minimum supply voltage of 2.3 VDC.

Precautions should be taken to insure that the power supply for the integrated circuit never becomes reversed in

polarity or that the unit is not inadvertently installed backwards in a test socket as an unlimited current surge

through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a

destroyed unit.

Large differential input voltages can be easily accommodated and, as input differential voltage protection diodes

are not needed, no large input currents result from large differential input voltages. The differential input voltage

may be larger than V+without damaging the device. Protection should be provided to prevent the input voltages

from going negative more than −0.3 VDC (at 25°C). An input clamp diode with a resistor to the IC input terminal

can be used.

To reduce the power supply current drain, the amplifiers have a class A output stage for small signal levels which

converts to class B in a large signal mode. This allows the amplifiers to both source and sink large output

currents. Therefore both NPN and PNP external current boost transistors can be used to extend the power

capability of the basic amplifiers. The output voltage needs to raise approximately 1 diode drop above ground to

bias the on-chip vertical PNP transistor for output current sinking applications.

For ac applications, where the load is capacitively coupled to the output of the amplifier, a resistor should be

used, from the output of the amplifier to ground to increase the class A bias current and prevent crossover

distortion. Where the load is directly coupled, as in dc applications, there is no crossover distortion.

Capacitive loads which are applied directly to the output of the amplifier reduce the loop stability margin. Values

of 50 pF can be accommodated using the worst-case non-inverting unity gain connection. Large closed loop

gains or resistive isolation should be used if larger load capacitance must be driven by the amplifier.

The bias network of the LM158 establishes a drain current which is independent of the magnitude of the power

supply voltage over the range of 3 VDC to 30 VDC.

Output short circuits either to ground or to the positive power supply should be of short time duration. Units can

be destroyed, not as a result of the short circuit current causing metal fusing, but rather due to the large increase

in IC chip dissipation which will cause eventual failure due to excessive function temperatures. Putting direct

short-circuits on more than one amplifier at a time will increase the total IC power dissipation to destructive

levels, if not properly protected with external dissipation limiting resistors in series with the output leads of the

amplifiers. The larger value of output source current which is available at 25°C provides a larger output current

capability at elevated temperatures (see TYPICAL PERFORMANCE CHARACTERISTICS) than a standard IC

op amp.

The circuits presented in the TYPICAL SINGLE-SUPPLY APPLICATIONS emphasize operation on only a single

power supply voltage. If complementary power supplies are available, all of the standard op amp circuits can be

used. In general, introducing a pseudo-ground (a bias voltage reference of V+/2) will allow operation above and

below this value in single power supply systems. Many application circuits are shown which take advantage of

the wide input common-mode voltage range which includes ground. In most cases, input biasing is not required

and input voltages which range to ground can easily be accommodated.

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

www.ti.com

CONNECTION DIAGRAM

Figure 15. PDIP/CDIP/SOIC Package – Top View Figure 16. TO-99 Package – Top View

(See Package Number P, NAB0008A, or D) (See Package Number LMC)

Figure 17. 8-Bump DSBGA - Top View, Bump Side Down

(See Package Number YPB0008AAA)

TYPICAL SINGLE-SUPPLY APPLICATIONS

(V+= 5.0 VDC)

Figure 18. Non-Inverting DC Gain (0V Output)

*R not needed due to temperature

independent IIN

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

www.ti.com

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

Where: VO= V1+ V2−V3−V4

(V1+ V2)≥(V3+ V4) to keep VO> 0 VDC

Figure 19. DC Summing Amplifier

(VIN'S ≥0 VDC and VO≥0 VDC)

VO= 0 VDC for VIN = 0 VDC

AV= 10

Figure 20. Power Amplifier

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

www.ti.com

fo= 1 kHz

Q = 50

Av= 100 (40 dB)

Figure 21. “BI-QUAD” RC Active Bandpass Filter

Figure 22. Fixed Current Sources

Figure 23. Lamp Driver

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

www.ti.com

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

Figure 24. LED Driver

*(Increase R1 for ILsmall)

VL≤V+−2V

Figure 25. Current Monitor

Figure 26. Driving TTL

VO= VIN

Figure 27. Voltage Follower

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

www.ti.com

Figure 28. Pulse Generator

Figure 29. Squarewave Oscillator

Figure 30. Pulse Generator

HIGH ZIN

LOW ZOUT

Figure 31. Low Drift Peak Detector

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

www.ti.com

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

IO= 1 amp/volt VIN

(Increase REfor IOsmall)

Figure 32. High Compliance Current Sink

Figure 33. Comparator with Hysteresis

*WIDE CONTROL VOLTAGE RANGE: 0 VDC ≤VC≤2 (V+−1.5V DC)

Figure 34. Voltage Controlled Oscillator (VCO)

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

www.ti.com

Figure 35. AC Coupled Inverting Amplifier

Figure 36. Ground Referencing a Differential Input Signal

Av= 11 (As Shown)

Figure 37. AC Coupled Non-Inverting Amplifier

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

www.ti.com

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

fo= 1 kHz

Q = 1

AV= 2

Figure 38. DC Coupled Low-Pass RC Active Filter

fo= 1 kHz

Q = 25

Figure 39. Bandpass Active Filter

Figure 40. High Input Z, DC Differential Amplifier

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

www.ti.com

Figure 41. Photo Voltaic-Cell Amplifier

Figure 42. Bridge Current Amplifier

Figure 43. High Input Z Adjustable-Gain DC Instrumentation Amplifier

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

www.ti.com

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

Figure 44. Using Symmetrical Amplifiers to Reduce Input Current (General Concept)

SCHEMATIC DIAGRAM

(Each Amplifier)

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

LM158-N, LM258-N, LM2904-N, LM358-N

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

www.ti.com

REVISION HISTORY

Changes from Revision G (March 2013) to Revision H Page

• Changed layout of National Data Sheet to TI format .......................................................................................................... 21

Product Folder Links: LM158-N LM258-N LM2904-N LM358-N

PACKAGE OPTION ADDENDUM

www.ti.com 1-Nov-2013

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

LM158AH ACTIVE TO-99 LMC 8 500 TBD Call TI Call TI -55 to 125 LM158AH

LM158AH/NOPB ACTIVE TO-99 LMC 8 500 Green (RoHS

& no Sb/Br) POST-PLATE Level-1-NA-UNLIM -55 to 125 LM158AH

LM158H ACTIVE TO-99 LMC 8 500 TBD Call TI Call TI -55 to 125 LM158H

LM158H/NOPB ACTIVE TO-99 LMC 8 500 Green (RoHS

& no Sb/Br) POST-PLATE Level-1-NA-UNLIM -55 to 125 LM158H

LM158J ACTIVE CDIP NAB 8 40 TBD Call TI Call TI -55 to 125 LM158J

LM258H ACTIVE TO-99 LMC 8 500 TBD Call TI Call TI -25 to 85 LM258H

LM258H/NOPB ACTIVE TO-99 LMC 8 500 Green (RoHS

& no Sb/Br) POST-PLATE Level-1-NA-UNLIM -25 to 85 LM258H

LM2904ITP/NOPB ACTIVE DSBGA YPB 8 250 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 A

LM2904ITPX/NOPB ACTIVE DSBGA YPB 8 3000 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 A

LM2904M NRND SOIC D 8 95 TBD Call TI Call TI -40 to 85 LM

2904M

LM2904M/NOPB ACTIVE SOIC D 8 95 Green (RoHS

& no Sb/Br) SN | CU SN Level-1-260C-UNLIM -40 to 85 LM

2904M

LM2904MX NRND SOIC D 8 2500 TBD Call TI Call TI -40 to 85 LM

2904M

LM2904MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS

& no Sb/Br) SN | CU SN Level-1-260C-UNLIM -40 to 85 LM

2904M

LM2904N NRND PDIP P 8 40 TBD Call TI Call TI -40 to 85 LM

2904N

LM2904N/NOPB ACTIVE PDIP P 8 40 Green (RoHS

& no Sb/Br) SN | CU SN Level-1-NA-UNLIM -40 to 85 LM

2904N

LM358AM NRND SOIC D 8 95 TBD Call TI Call TI 0 to 70 LM

358AM

LM358AM/NOPB ACTIVE SOIC D 8 95 Green (RoHS

& no Sb/Br) SN | CU SN Level-1-260C-UNLIM 0 to 70 LM

358AM

LM358AMX NRND SOIC D 8 2500 TBD Call TI Call TI 0 to 70 LM

358AM

PACKAGE OPTION ADDENDUM

www.ti.com 1-Nov-2013

Addendum-Page 2

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

LM358AMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS

& no Sb/Br) SN | CU SN Level-1-260C-UNLIM 0 to 70 LM

358AM

LM358AN NRND PDIP P 8 40 TBD Call TI Call TI 0 to 70 LM

358AN

LM358AN/NOPB ACTIVE PDIP P 8 40 Green (RoHS

& no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 70 LM

358AN

LM358H/NOPB ACTIVE TO-99 LMC 8 500 Green (RoHS

& no Sb/Br) POST-PLATE Level-1-NA-UNLIM 0 to 70 LM358H

LM358M NRND SOIC D 8 95 TBD Call TI Call TI 0 to 70 LM

358M

LM358M/NOPB ACTIVE SOIC D 8 95 Green (RoHS

& no Sb/Br) SN | CU SN Level-1-260C-UNLIM 0 to 70 LM

358M

LM358MX NRND SOIC D 8 2500 TBD Call TI Call TI 0 to 70 LM

358M

LM358MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS

& no Sb/Br) SN | CU SN Level-1-260C-UNLIM 0 to 70 LM

358M

LM358N NRND PDIP P 8 40 TBD Call TI Call TI 0 to 70 LM

358N

LM358N/NOPB ACTIVE PDIP P 8 40 Green (RoHS

& no Sb/Br) SN | CU SN Level-1-NA-UNLIM 0 to 70 LM

358N

LM358TP/NOPB ACTIVE DSBGA YPB 8 250 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM 0 to 70 A

LM358TPX/NOPB ACTIVE DSBGA YPB 8 3000 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM 0 to 70 A

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

PACKAGE OPTION ADDENDUM

www.ti.com 1-Nov-2013

Addendum-Page 3

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

LM2904ITP/NOPB DSBGA YPB 8 250 178.0 8.4 1.5 1.5 0.66 4.0 8.0 Q1

LM2904ITPX/NOPB DSBGA YPB 8 3000 178.0 8.4 1.5 1.5 0.66 4.0 8.0 Q1

LM2904MX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

LM2904MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

LM358AMX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

LM358AMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

LM358MX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

LM358MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

LM358TP/NOPB DSBGA YPB 8 250 178.0 8.4 1.5 1.5 0.66 4.0 8.0 Q1

LM358TPX/NOPB DSBGA YPB 8 3000 178.0 8.4 1.5 1.5 0.66 4.0 8.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 8-Apr-2013

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

LM2904ITP/NOPB DSBGA YPB 8 250 210.0 185.0 35.0

LM2904ITPX/NOPB DSBGA YPB 8 3000 210.0 185.0 35.0

LM2904MX SOIC D 8 2500 367.0 367.0 35.0

LM2904MX/NOPB SOIC D 8 2500 367.0 367.0 35.0

LM358AMX SOIC D 8 2500 367.0 367.0 35.0

LM358AMX/NOPB SOIC D 8 2500 367.0 367.0 35.0

LM358MX SOIC D 8 2500 367.0 367.0 35.0

LM358MX/NOPB SOIC D 8 2500 367.0 367.0 35.0

LM358TP/NOPB DSBGA YPB 8 250 210.0 185.0 35.0

LM358TPX/NOPB DSBGA YPB 8 3000 210.0 185.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 8-Apr-2013

Pack Materials-Page 2

MECHANICAL DATA

NAB0008A

www.ti.com

J08A (Rev M)

MECHANICAL DATA

YPB0008

www.ti.com

TPA08XXX (Rev A)

0.5±0.045 D

4215100/A 12/12

. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.

B. This drawing is subject to change without notice.

NOTES:

D: Max =

E: Max =

1.337 mm, Min =

1.276 mm

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest

issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and

complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale

supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of

non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com

Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265