LE910 Family Product Description Preliminary 80421ST10587a Rev.2 - 2013-10-08 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 APPLICABILITY TABLE PRODUCT LE910 Series Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 2 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 Disclaimer The information contained in this document is the proprietary information of Telit Communications S.p.A. and its affiliates ("TELIT"). The contents are confidential and any disclosure to persons other than the officers, employees, agents or subcontractors of the owner or licensee of this document, without the prior written consent of Telit, is strictly prohibited. Telit makes every effort to ensure the quality of the information it makes available. Notwithstanding the foregoing, Telit does not make any warranty as to the information contained herein, and does not accept any liability for any injury, loss or damage of any kind incurred by use of or reliance upon the information. Telit disclaims any and all responsibility for the application of the devices characterized in this document, and notes that the application of the device must comply with the safety standards of the applicable country, and where applicable, with the relevant wiring rules. Telit reserves the right to make modifications, additions and deletions to this document due to typographical errors, inaccurate information, or improvements to programs and/or equipment at any time and without notice. Such changes will, nevertheless be incorporated into new editions of this document. Copyright: Transmittal, reproduction, dissemination and/or editing of this document as well as utilization of its contents and communication thereof to others without express authorization are prohibited. Offenders will be held liable for payment of damages. All rights are reserved. Copyright (c) Telit Communications S.p.A. 2013 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 3 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 Contents 1. 2. 3. Introduction ............................................................................................................. 6 1.1. Scope ............................................................................................................................ 6 1.2. Audience....................................................................................................................... 6 1.3. Contact Information, Support ...................................................................................... 6 1.4. Document Organization ............................................................................................... 7 1.5. Text Conventions .......................................................................................................... 7 1.6. Related Documents ..................................................................................................... 8 1.7. Document History ........................................................................................................ 8 The LE910 ................................................................................................................ 9 2.1. Product Overview ......................................................................................................... 9 2.2. Target Market ............................................................................................................ 10 2.3. Product variants ......................................................................................................... 10 2.4. Product Features ....................................................................................................... 11 Product Description ............................................................................................... 14 3.1. Dimensions and 2D mechanical drawing .................................................................. 14 3.2. Weight ........................................................................................................................ 15 3.3. Environmental requirements .................................................................................... 15 3.3.1. Temperature range .......................................................................................................... 15 3.3.2. RoHS compliance ............................................................................................................. 15 3.4. Operating Frequency ................................................................................................. 16 3.5. Antenna ...................................................................................................................... 17 3.6. Supply voltage ............................................................................................................ 17 3.7. The user interface ...................................................................................................... 17 3.8. Input and Outputs ...................................................................................................... 18 3.8.1. General Purpose I/Os ....................................................................................................... 18 3.8.2. Power on monitor (PWRMON).......................................................................................... 18 3.8.3. Power on/off control (ON_OFF) ....................................................................................... 18 3.8.4. Auxiliary power output for accessory (VAUX) .................................................................. 18 3.8.5. SIM Reader ....................................................................................................................... 18 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 4 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 3.8.6. Serial ports .......................................................................................................................18 3.8.7. USB port............................................................................................................................18 3.9. Converters.................................................................................................................. 19 3.9.1. ADC Converter .................................................................................................................. 19 3.9.2. DAC Converter .................................................................................................................. 19 3.10. Logic level specifications ....................................................................................... 19 3.11. Audio ....................................................................................................................... 19 3.11.1. 3.12. Digital ................................................................................................................................19 Other features ........................................................................................................ 19 3.12.1. Speech CODEC.................................................................................................................. 19 3.12.2. SMS ...................................................................................................................................19 3.12.3. Phonebook ........................................................................................................................20 3.12.4. Call status indication ........................................................................................................ 20 3.13. Mounting the modules on your board .................................................................... 21 3.14. Packing system....................................................................................................... 21 4. Evaluation Kit ......................................................................................................... 22 5. AT Commands ........................................................................................................ 23 6. Safety Recommendations ....................................................................................... 24 7. List of acronyms .................................................................................................... 25 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 5 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 1. Introduction 1.1. Scope Scope of this document is to give an overview of the Telit LE910 series, which can support LTE, with data/voice capabilities, and GSM/GPRS/UMTS/HSPA+ as fall-back technologies. 1.2. Audience This document is intended for customers who are evaluating the LE910 series. 1.3. Contact Information, Support For general contact, technical support, to report documentation errors and to order manuals, contact Telit Technical Support Center (TTSC) at: TS-EMEA@telit.com TS-NORTHAMERICA@telit.com TS-LATINAMERICA@telit.com TS-APAC@telit.com Alternatively, use: http://www.telit.com/en/products/technical-support-center/contact.php For detailed information about where you can buy the Telit modules or for recommendations on accessories and components visit: http://www.telit.com To register for product news and announcements or for product questions contact Telit Technical Support Center (TTSC). Our aim is to make this guide as helpful as possible. Keep us informed of your comments and suggestions for improvements. Telit appreciates feedback from the users of our information. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 6 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 1.4. Document Organization This document contains the following chapters (sample): "Chapter 1: "Introduction" provides a scope for this document, target audience, contact and support information, and text conventions. "Chapter 2: "Overview" gives the information of product variants and the overview of the characteristics and features of the product. "Chapter 3: "General Product Description" describes in details the characteristics of the product. "Chapter 4: "Evaluation Kit" provides a brief description of the Telit Evaluation Kit (EVK2) as far as these modules are concerned. "Chapter 5: "Software Features" provides an overview of the software features of the products. "Chapter 6: "AT Commands" provides the information of compliant. "Chapter 7: "Conformity Assessment" provides some fundamental hints about the conformity assessment that the final application might need. "Chapter 8: "Safety Recommendation" provides some safety recommendations that must be follow by the customer in the design of the application that makes use of the LE910 family. 1.5. Text Conventions Danger - This information MUST be followed or catastrophic equipment failure or bodily injury may occur. Caution or Warning - Alerts the user to important points about integrating the module, if these points are not followed, the module and end user equipment may fail or malfunction. Tip or Information - Provides advice and suggestions that may be useful when integrating the module. All dates are in ISO 8601 format, i.e. YYYY-MM-DD. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 7 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 1.6. 1.7. Related Documents * LE910 Hardware User Guide * LE910 AT command User Guide * Telit EVK2 User Guide, Document History Revision 0 1 2 Date 2012-11-28 2013-09-12 2013-10-08 Changes First issue General Review of the document Product variants update Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 8 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 2. The LE910 2.1. Product Overview The new Telit LE910 represents the next generation of Telit wireless connectivity with xE910 form factor. The LE910 combines the two cutting edge technologies HSPA+ and LTE. As a matter of fact, LE910 is a 3.5G wireless data module offering HSPA+ connectivity with download speeds up to 42 Mbps, and a 4G M2M module at the same time, providing an ultra high-speed downlink at 100 Mbps. The LE910 will be the first and smallest module in the market incorporating 2G/3G/4G solution. Designed for use in the most demanding industrial and consumer applications, the LE910 offers LGA packaging with cost effective mating solution. Three LE910 regional versions are available, one for European, APAC and Latin American markets and two for the North American market ( AT&T and Verizon configuration). All of them come with a multiband configuration, covering different sets of 3G and 4G bands. Developers can take advantage of Telit's xE910 Unified Form Factor that enables a "design once, use anywhere" strategy. Due to its low profile, low consumption and advanced connectivity features, LE910 is particularly suitable for applications such as mobile computing devices, PDAs, smatphones, table PCS and counsumer or industial electronics in general. Design your application once and choose the technology that best fits the regional requirements for a truly seamless deployment. The LE910 is also fully backwards compatible to existing EDGE and GSM/GPRS networks through integrated quad-band radios. Additional features, such as integrated TCP/IP and UDP stack, DAC and ADC channels provide extended functionality, adding value to the final application with no additional costs. Moreover LE910 is also available with embedded GPS/GLONASS receiver and Antenna Diversity. The extensive interface set, which includes USB, SPI, I2C and user definable GPIOs, provides ease of integration of peripherals and actuators. As a part of Telit's corporate policy of environmenta protection, LE910 as all Telit products comply with the RoHS (Restriction of Hazardous Substance) directive of the European Union (Eu Directive 2011/65/EU). Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 9 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 NOTE: Some of the performances of the Telit modules depend on S/W version installed on the module itself. The Telit modules S/W group is continuously working in order to add new features and improve the overall performances. The Telit modules are easily upgraded by the developer using the Telit Flash Programmer. NOTE: In order to meet the competitive OEM and vertical market stringent requirements, Telit supports its customers with a dedicated Support Policy with: 2.2. Telit Evaluation Kit EVK2 to help you to develop your application; A website with all updated information available; An high level specialist technical support to assist you in your development; Target Market The LE910 is designed and developed for applications requiring high throughput, devices requiring worldwide coverage and for applications in areas such as telematics for in-vehicle infotainment, video security and surveillance, outdoor signs and displays, business terminals and consumer products such as routers, mobile hot-spots, etc. 2.3. Product variants Variant 2G Frequencies (MHz) WCDMA Frequencies (MHz/Band) LTE Frequencies (MHz/Band) LE910-EUG 850/900/1800/1900 900 (B8) 2100 (B1) 800 (B20) 1800 (B3) 2600 (B7) LE910-NAG (AT&T) 850/1900 850 (B5) 1900 (B2) 700 (B17) 850 (B5) AWS1700 (B4) 1900 (B2) LE910-NAx (Verizon) - 850 (B5) 1900 (B2) 700 (B13) AWS1700 (B4) HSPA+ Data - Rates DL/UL [Mbps] LTE Data - Rates DL/UL [Mbps] 42/5.7 100/50 42/5.7 100/50 42/5.7 100/50 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 10 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 2.4. Product Features * * Dual/Quad-band EGSM class 10 Multi-band UMTS/HSPA+ o 900/2100 MHz (EU variant) o 850/1900 MHz (NAx variants) * Multi-band LTE o 850/1800/2100 MHz (EU variant) o 700/850/AWS1700/1900 MHz (AT&T variant) o 700/AWS1700 MHz (Verizon variant) * * 3GPP protocol stack release 9 compliant, LTE Cat.3 Supply voltage range: 3.4 - 4.2 V DC (3.8 V DC nominal) * Output power o Class 4 (2 W, 33 dBm) @ GSM 900 o Class 1 (1 W, 30 dBm) @ GSM 1800 o Class E2 (0.5 W, 27 dBm) @ EDGE 900 o Class E2 (0.4 W, 26 dBm) @ EDGE 1800 o Class 3 (0.25 W, 24 dBm) @ UMTS o Class 3 (0.2 W, 23 dBm) @ LTE * * Digital Audio and VoLTE (Voice over LTE) Control via AT commands according to 3GPP 27.005, 27.007 and Telit custom AT commands SIM Application Toolkit 3GPP TS 51.014 SIM Access Profile IP stack with TCP and UDP protocol E-Call compliant Embedded GPS/Glonass Rx Diversity & MIMO Dimensions: 28.2 x 28.2 x 2.55 mm Weight: 9 grams RoHS compliant * * * * * * * * * Interfaces * 10 I/O ports * Digital voice support * USB 2.0 HS * 1 UART * SPI * I2C * 1.8V SIM Interface Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 11 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 Data transmission * LTE Cat.3 o DL up to 100 Mbps o UL up 50 Mbps * HSPA+: category 20 in downlink e category 6 in uplink o DL up to 42.0Mbps o UL up to 5.76Mbps * WCDMA: up to 384kbps downlink/uplink * EDGE: DL up to 236.8 kbps, UL up to 236.8 kbps * GPRS: DL up to 85,6 kbps, UL up to 85.6kbps * Asynchronous non-transparent CSD up to 9.6kbps * EDGE Class 10, MS class B * Coding scheme 1 to 4 (GPRS) & Modulation Coding scheme 1 to 9 (EDGE) Audio * Telephony * Half rate, full rate, enhanced full rate and adaptive multi rate voice codecs (HR, FR, EFR, AMR) * Superior echo cancellation & noise reduction * DTMF SMS * * * * * Point-to-point mobile originated and mobile terminated SMS Concatenated SMS supported SMS cell broadcast Text and PDU mode SMS over GPRS GPRS data * GPRS class 10 * Mobile station class B * Coding scheme 1 to 4 * PBCCH support * GERAN Feature Package 1 support (NACC, Extended TBF) GSM Supplementary Services * Call forwarding * Call barring * Call waiting & call hold * Advice of charge * Calling line identification presentation (CLIP) * Calling line identification restriction (CLIR) * Unstructured supplementary services mobile originated data (USSD) * Closed user group Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 12 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 Additional features * SIM phonebook * Fixed Dialling Number (FDN) * Call control & status indication * SIM phonebook * Character management (IRA, UCS2, GSM) * USIM 3GPP Rel.7 * Real Time Clock * Automatic answer * Alarm management * Embedded TCP/IP stack, including TCP, IP, UDP, and FTP protocols * CSD for Video Telephony support Approvals * Fully type approved conforming with R&TTE directive * CE, GCF, FCC, PTCRB, IC Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 13 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 3. Product Description 3.1. Dimensions and 2D mechanical drawing The LE910 has a Land-Grid-Array (LGA) package, with 144 pads. The overall dimensions of LE910 family are: Length: 28.2 mm Width: 28.2mm Thickness: 2.55 mm Pin B1 Bottom view Dimensions in mm Lead-free Alloy: Surface finishing Ni/Au for all solder pads Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 14 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 3.2. Weight The module weight of LE910 family is about 9 grams. 3.3. Environmental requirements 3.3.1. Temperature range Operating Temperature Range 3.3.2. -40C ~ +85C RoHS compliance As a part of Telit corporate policy of environmental protection, the HE863 family complies with the RoHS (Restriction of Hazardous Substances) directive of the European Union (EU directive 2011/65/EU). Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 15 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 3.4. Operating Frequency The operating frequencies in GSM850, EGSM900, DCS1800, PCS1900, WCDMA modes are compliant to the 3GPP and WCDMA specifications. Mode Freq. TX (MHz) Freq. RX (MHz) Channels TX - RX offset DCS1800 890.0 ~ 915 880.2 ~ 889.8 1710.2 ~ 1784.8 935.0 ~ 959.8 925.2 ~ 934.8 1805.2 ~ 1879.8 0 ~ 124 975 ~ 1023 512 ~ 885 45 MHz 45 MHz 95MHz WCDMA2100 - B1 1922.4 ~ 1977.6 2112.4 ~ 2167.6 Tx: 9612 ~ 9888 Rx: 10562 ~ 10838 190MHz WCDMA1900 - B2 1852.4 ~ 1907.6 1932.4 ~ 1987.6 WCDMA1800 - B3 1710 ~ 1785 1805 ~ 1880 WCDMA850 - B5 826.4 ~ 846.6 871.4 ~ 891.6 WCDMA900 -B8 882.4 ~ 912.6 927.4 ~ 957.6 LTE2100 - B1 1920 ~ 1980 2110 ~ 2170 LTE1900 - B2 1850 ~ 1910 1930 ~ 1990 LTE1800 - B3 1710 ~ 1785 1805 ~ 1880 LTE1700 - B4 1710~ 1755 2110 ~ 2155 LTE850 - B5 824 ~ 849 869 ~ 894 LTE700 - B17 704 ~ 716 734 ~ 746 EGSM900 Tx: 9262 ~ 9538 Rx: 9662 ~ 9938 Tx: 937 ~ 1288 Rx: 1162 ~ 1513 Tx: 4132 ~ 4233 Rx: 4357 ~ 4458 Tx: 2712 ~ 2863 Rx: 2937 ~ 3088 Tx: 18000 ~ 18599 Rx: 0 ~ 599 Tx: 18600 ~ 19199 Rx: 600 ~ 1199 Tx: 19200 ~ 19949 Rx: 1200 ~ 1949 Tx: 19950 ~ 20399 Rx: 1950 ~ 2399 Tx: 20400 ~ 20649 Rx: 2400 ~ 2649 Tx: 23730 ~ 23849 Rx: 5730 ~ 5849 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. 80MHz 95MHz 45MHz 45MHz 190MHz 80MHz 95MHz 400MHz 45MHz 30MHz Page 16 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 3.5. Antenna The antenna connection and board layout design are the most important parts in the full product design and they strongly reflect on the product's overall performances. Read carefully and follow the requirements described in the Hardware User Guide. 3.6. Supply voltage The external power supply must be connected to VBATT signal and must fulfill the following requirements: 3.7. Nominal Supply Voltage 3.8V Operating Voltage Range 3.4 ~ 4.2V The user interface The user interface is managed by AT commands according to ITU-T V.250, 3GPP 27.007 and 27.005 specifications. Moreover, custom AT commands are also available. Please refer to the AT Command User Guide for details. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 17 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 3.8. Input and Outputs 3.8.1. General Purpose I/Os 10 pins of general purpose I/Os can be configured by AT command in three different ways as input, output and alternative function. 3.8.2. Power on monitor (PWRMON) The PWRMON indicates the status of the module running properly. 3.8.3. Power on/off control (ON_OFF) External power on/off control input. Refer to the LE910 family Hardware User Guide for more details of Power on timing. 3.8.4. Auxiliary power output for accessory (VAUX) A regulated 1.8V power output is provided for an external device. 3.8.5. SIM Reader The LE910 family supports 1 SIM/USIM at 1.8V ONLY with and external SIM connector. For 3V or 5V SIM, an external level translator can be added. Refer to the LE910 family Hardware User Guide. 3.8.6. Serial ports Two serial ports are available. 3.8.7. Full RS232-C Simplified serial port (RX/TX only) for debugging USB port The USB2.0 High Speed have a clock rate of 480MHz Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 18 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 3.9. Converters 3.9.1. ADC Converter The LE910 has one on board ADC, which are 8-bit converters. It is able to read a voltage level in the range of 0/2 volts applied on the ADC pin input, store and convert it into 8 bit word. 3.9.2. DAC Converter The LE910 module provides a Digital to Analog Converter. The on board DAC is in the range from 0 to 1023. 3.10. Logic level specifications Where not specifically stated, all the interface circuits work at 1.8V CMOS logic levels. To get more detailed information about the logic level specifications used in the LE910, please check with the Hardware User Guide. 3.11. Audio Future proof support to VoLTE (Voice over LTE). In addition the module automatically falls back to HSPA+ if it is unable to register onto an LTE network. The series supports CSFB (circuit switched fallback) allowing the modules to sustain voice services through automatic fallback to 3G or 2G when an LTE network is not present, when roaming, or if IMS (IP Multimedia Subsystem) is not supported by the network. 3.11.1. Digital The LE910 offers the digital voice interface as well. 3.12. Other features 3.12.1. Speech CODEC The LE910 supports the following voice codec: * HR - Half Rate * FR - Full Rate * EFR - Enhanced Full Rate * AMR-HR, AMR Half Rate * AMR-FR, AMR Full Rate 3.12.2. SMS The LE910 supports the following SMS types: * Mobile Terminated (MT) class 0 - 3 with signalling of new incoming SMS, SIM full, SMS read. * Mobile Originated class 0 - 3 with writing, saving in SIM and sending * Cell broadcast compatible with CB DRX with signalling of new incoming SMS. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 19 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 The LE910 also supports SMS over GPRS. 3.12.3. Phonebook This function allows the storing of the telephone numbers in SIM memory. The capability depends on SIM version and its embedded memory. 3.12.4. Call status indication The call status indication is supported. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 20 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 3.13. Mounting the modules on your board The modules have been designed in order to be compliant with a standard lead-free SMT process. For detailed information about PCB pad design and conditions to use in SMT process, please refer to the respective Hardware User Guide. 3.14. Packing system According to SMT process, for picking & placing movement requirements, LE910 family is packaged on trays. Each tray contains 20 pieces in size of 176 x 329. The level of moisture sensibility of LE910 family is "3", according with standard IPC/JEDEC J-STD-020, take care of all the relative requirements for using this kind of components. Special care for handling is highly required. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 21 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 4. Evaluation Kit In order to assist the customer in the development of the application, Telit offers the EVK2 Evaluation Kit that can be ordered separately. The EVK2 has a SIM card holder, the RS 232 serial port level translator, a direct UART connection, audio and antenna connector. The EVK2 provides a fully functional solution for a complete data or phone application. The standard serial RS232 9 pin connector placed on the Evaluation Kit allows the connection of the EVK2 system with a PC or other DTE. The development of the applications utilizing the Telit LE910 family must present a proper design of all the interfaces towards and from the module (e.g. power supply, audio paths, level translators), otherwise a decrease in the performances will be introduced or, in the worst case, a wrong design can even lead to an operating failure of the module. In order to assist the hardware designer in his project phase, the EVK2 board presents a family of different solutions, which will cover the most common design requirements on the market, and which can be easily integrated in the OEM design as building blocks or can be taken as starting points to develop a specific one. For a detailed description of the Telit Evaluation Kit, please refer to the documentation provided with the respective Hardware User Guide and EVK2 User Manual. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 22 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 5. AT Commands The Telit LE910 module can be driven via the serial and USB interface using the standard AT commands. The module is compliant with: 1. Hayes standard AT command set, in order to maintain the compatibility with existing SW programs. 2. 3GPP 27.007 specific AT command and GPRS specific commands. 3. 3GPP 27.005 specific AT commands for SMS (Short Message Service) and CBS (Cell Broadcast Service) Moreover the LE910 module supports also Telit proprietary AT commands for special purposes. For a more information about AT commands supported by the LE910 module please refer to the document AT Commands Reference Guide. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 23 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 6. Safety Recommendations READ CAREFULLY Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas: * Where it can interfere with other electronic devices in environments such as hospitals, airports, aircrafts, etc. * Where there is risk of explosion such as gasoline stations, oil refineries, etc. It is responsibility of the user to enforce the country regulation and the specific environment regulation. Do not disassemble the product; any mark of tampering will compromise the warranty validity. We recommend following the instructions of the hardware user guides for a correct wiring of the product. The product has to be supplied with a stabilized voltage source and the wiring has to be conforming to the security and fire prevention regulations. The product has to be handled with care, avoiding any contact with the pins because electrostatic discharges may damage the product itself. Same cautions have to be taken for the SIM, checking carefully the instruction for its use. Do not insert or remove the SIM when the product is in power saving mode. The system integrator is responsible of the functioning of the final product; therefore, care has to be taken to the external components of the module, as well as of any project or installation issue, because the risk of disturbing the WCDMA/GSM network or external devices or having impact on the security. Should there be any doubt, please refer to the technical documentation and the regulations in force. Every module has to be equipped with a proper antenna with specific characteristics. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case of this requirement cannot be satisfied, the system integrator has to assess the final product against the SAR regulation. The European Community provides some Directives for the electronic equipments introduced on the market. All the relevant information's are available on the European Community website: http://ec.europa.eu/enterprise/sectors/rtte/documents/ The text of the Directive 99/05 regarding telecommunication equipments is available, while the applicable Directives (Low Voltage and EMC) are available at: http://ec.europa.eu/enterprise/sectors/electrical/ Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 24 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 7. List of acronyms 3GPP 3rd Generation Partnership Project ADC Analog to Digital Converter ADN Abbreviated Dialing Number A-GPS Assisted GPS AMR Adaptive Multi Rate AT Attention Commands AWS Advanced Wireless Services BER Bit Error Rate BGA Ball Grid Array CLIP Calling Line Identification Presentation CLIR Calling Line Identification Restriction CMOS Complementary Metal-Oxide Semiconductor CSD Circuit Switched Data DAC Digital to Analog Converter DARP Downlink Advanced Receiver Performance DTMF Dual Tone Multi Frequency FDN Fixed Dialing Number FTP File Transfer Protocol GSM Global System for Mobile communication GPRS General Packet Radio Service GPS Global Positioning System HSPA High Speed Packet Access HSUPA High Speed Uplink Packet Access H/W Hardware LED Light Emitting Diode MO Mobile Originated MT Mobile Terminated OEM Other Equipment Manufacturer PCB Printed Circuit Board Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 25 of 26 LE910 Family Product Description 80421ST10587a- Rev.2- 2013-10-08 PCM Pulse Code Modulation PDA Personal Digital Assistant PDU Protocol Data Unit PIN Personal Identification Number POS Point Of Sales PWM Pulse Width Modulation RF Radio Frequency RoHS Restriction of Hazardous Substances RTC Real Time Clock SAIC Single Antenna Interface Cancellation SIM Subscriber Identity Module SMD Surface Mounted Device SMS Short Message Service S/W Software TBD To Be Determined TCP/IP Transmission Control Protocol/Internet Protocol TTSC Telit Technical Support Center UART Universal Asynchronous Receiver and Transmitter USB Universal Serial Bus USIM Universal Subscriber Identity Module WCDMA Wideband Code Division Multiple Access Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 26 of 26