Standard Products ACT8518 32-Channel Analog Multiplexer Module Radiation Tolerant & ESD Protected www.aeroflex.com/mux November 18, 2008 FEATURES 32 Channels provided by two independent 16-channel multiplexers Radiation performance - Total dose: 150 krads(Si), Dose rate = 50 - 300 rads(Si)/s - SEU: Immune up to 90 MeV-cm2/mg - SEL: Immune by process design Full military temperature range Low power consumption < 30mW Two address busses (A0-3 & B0-3), and two enable lines afford flexible organization All channel Inputs protected by 20V nominal transorbs Fast access time < 500ns typical Break-Before-Make switching High analog input impedance (power on or off) Designed for aerospace and high reliability space applications Packaging - Hermetic ceramic - 96 leads, 1.32"Sq x 0.20"Ht quad flat pack - Typical Weight 15 grams DSCC SMD 5962-09204 pending Note: Aeroflex Plainview does not currently have a DSCC certified Radiation Hardened Assurance Program. GENERAL DESCRIPTION Aeroflex's ACT8518 is a radiation tolerant, 32 channel multiplexer MCM (multi-chip module) with electrostatic discharge (ESD) protection on all channel inputs. The ACT8518 has been specifically designed to meet exposure to radiation environments. It is available in a 96 lead High Temperature Co-Fired Ceramic (HTCC) Quad Flatpack (CQFP). It is guaranteed operational from -55C to +125C. Available screened in accordance with MIL-PRF-38534, the ACT8518 is ideal for demanding military and space applications. ORGANIZATION AND APPLICATION The ACT8518 consists of two 16 channel multiplexers arranged as shown in the Block Diagram. The ACT8518 design is inherently radiation tolerant. A SECTION Sixteen (16) channels addressable by bus A0~A3, in one 16 channel block including enable. B SECTION Sixteen (16) channels addressable by bus B0~B3, in one 16 channel block including enable. SCD8518 Rev D SECTION B 16 CH 0 * * * 16 VR MUX 1 OUTPUT 0-15 CH 15 EN 0-15 B0 B1 B2 B3 SECTION A 16 CH 16 * * * 16 VR MUX 2 OUTPUT 16-31 CH 31 EN 16-31 A0 A1 A2 A3 +VEE -VEE VREF GND ACT8518 32 - CHANNEL ANALOG MUX BLOCK DIAGRAM SCD8518 Rev D 11/18/08 2 Aeroflex Plainview ABSOLUTE MAXIMUM RATINGS 1/ Parameter Range Units Case Operating Temperature Range -55 to +125 C Storage Temperature Range -65 to +150 C +20 -20 +7.5 V V V < VREF +.5 > GND -.5 V V 18V V Supply Voltage +VEE (Pin 44) -VEE (Pin 46) VREF (Pin 48) Digital Input Overvoltage VEN (Pins 5, 92), VA (Pins 1, 3, 93, 95), VB (Pins 2, 4, 94, 96) Analog Input Over Voltage VS Notes: 1/ All measurements are made with respect to ground. NOTICE: Stresses above those listed under "Absolute Maximums Rating" may cause permanent damage to the device. These are stress rating only; functional operation beyond the "Operation Conditions" is not recommended and extended exposure beyond the "Operation Conditions" may affect device reliability. RECOMMENDED OPERATING CONDITIONS 1/ Symbol Parameter Typical Units +VEE +15V Power Supply Voltage +15.0 V -VEE -15V Power Supply Voltage -15.0 V VREF Reference Voltage +5.00 V VAL Logic Low Level +0.8 V VAH Logic High Level +4.0 V 1/ Power Supply turn-on sequence shall be as follows: -VEE, VREF, followed by +VEE. DC ELECTRICAL PERFORMANCE CHARACTERISTICS 1/ (TC = -55C TO +125C, -VEE = -15V, VREF = +5.0V, +VEE= +15V - UNLESS OTHERWISE SPECIFIED) Parameter Supply Current Address Input Current Enable Input Current SCD8518 Rev D 11/18/08 Symbol Conditions Min Max Units +IEE VEN(0-31) = VA(0-3)A = VA(0-3)B = 0 0 1 mA -IEE VEN(0-31) = VA(0-3)A = VA(0-3)B = 0 -1 0 mA +ISBY VEN(0-31) = 4V, VA(0-3)A = VA(0-3)B = 0 7/ 0 1 mA -ISBY VEN(0-31) = 4V, VA(0-3)A = VA(0-3)B = 0 7/ -1 0 mA IAL(0-3)A VA = 0V -1 1 A IAH(0-3)A VA = 5V -1 1 A IAL(0-3)B VB = 0V -1 1 A IAH(0-3)B VB = 5V -1 1 A IENL(0-15) VEN(0-15) = 0V -1 1 A IENH(0-15) VEN(0-15) = 5V -1 1 A IENL(16-31) VEN(16-31) = 0V -1 1 A IENH(16-31) VEN(16-31) = 5V -1 1 A 3 Aeroflex Plainview DC ELECTRICAL PERFORMANCE CHARACTERISTICS 1/ (continued) (TC = -55C TO +125C, -VEE = -15V, VREF = +5.0V, +VEE= +15V - UNLESS OTHERWISE SPECIFIED) Parameter Symbol Conditions Min Max Units Positive Input Leakage Current CH0-CH31 +ISOFFOUTPUT VIN = +10V, VEN = 4V, output and all unused MUX inputs under test = -10V 2/, 3/ -100 +1000 nA Negative Input Leakage Current CH0-CH31 -ISOFFOUTPUT VIN = -10V, VEN = 4V, output and all unused MUX inputs under test = +10V 2/, 3/ -100 +1000 nA Output Leakage Current OUTPUTS (pins 25 & 70) +IDOFFOUTPUT VOUT = +10V, VEN = 4V, output and all unused MUX inputs under test = -10V 3/, 4/ -100 +100 nA Output Leakage Current OUTPUTS (pins 25 & 70) -IDOFFOUTPUT VOUT = -10V, VEN = 4V, output and all unused MUX inputs under test = +10V 3/, 4/ -100 +100 nA +25C +125C -55C 18.0 18.0 17.5 23.0 23.5 22.5 V V V +25C +125C -55C -23.0 -23.5 -22.5 -18.0 -18.0 -17.5 V V V Input Clamped Voltage CH0 - CH31 +VCLMP Input Clamped Voltage CH0 - CH31 -VCLMP Switch ON Resistance OUTPUTS (pins 25 & 70) RDS(ON)(0-31)A VIN = +15V, VEN = 0.8V, IOUT = -1mA 2/, 3/, 5/ 200 1000 RDS(ON)(0-31)B VIN = +5V, VEN = 0.8V, IOUT = -1mA 2/, 3/, 5/ 200 1500 RDS(ON)(0-31)C VIN = -5V, VEN = 0.8V, IOUT = +1mA 2/, 3/, 5/ 200 2500 6/ VEN = 4V, all unused MUX inputs under test are open. 3/ Notes: 1/ Measure inputs sequentially. Ground all unused inputs of the device under test. VA is the applied input voltage to the address lines A(0-3). VB is the applied input voltage to the address lines B(0-3). 2/ VIN is the applied input voltage to the input channels CH0-CH31. 3/ VEN is the applied input voltage to the enable lines En(0-15), En(16-31). 4/ VOUT is the applied input voltage to the output lines OUTPUT(0-15), OUTPUT(16-31). 5/ Negative current is the current flowing out of each of the MUX pins. Positive current is the current flowing into each MUX pin. 6/ The ACT8518 cannot be operated with analog inputs from -15 to -5 volts. 7/ Not tested, guaranteed to the specified limits. SWITCHING CHARACTERISTICS (Tc = -55C to +125C, -VEE = -15V, VREF = +5.0V, +VEE = +15V -- Unless otherwise specified) Parameter Switching Test MUX Symbol Conditions tAHL Min Max Units 10 1000 ns 10 1000 ns 10 1000 ns 10 1000 ns RL = 10K, CL = 50pF tALH tONEN RL = 1K, CL = 50pF tOFFEN SCD8518 Rev D 11/18/08 4 Aeroflex Plainview TRUTH TABLE (CH0 - CH15) TRUTH TABLE (CH16 - CH31) B3 B2 B1 B0 EN(0-15) "ON" CHANNEL 1/ A3 A2 A1 A0 EN(16-31) "ON" CHANNEL 1/ X X X X H NONE X X X X H NONE L L L L L CH0 L L L L L CH16 L L L H L CH1 L L L H L CH17 L L H L L CH2 L L H L L CH18 L L H H L CH3 L L H H L CH19 L H L L L CH4 L H L L L CH20 L H L H L CH5 L H L H L CH21 L H H L L CH6 L H H L L CH22 L H H H L CH7 L H H H L CH23 H L L L L CH8 H L L L L CH24 H L L H L CH9 H L L H L CH25 H L H L L CH10 H L H L L CH26 H L H H L CH11 H L H H L CH27 H H L L L CH12 H H L L L CH28 H H L H L CH13 H H L H L CH29 H H H L L CH14 H H H L L CH30 H H H H L CH15 H H H H L CH31 1/ Between CH0-15 and OUTPUT (0-15) SCD8518 Rev D 11/18/08 1/ Between CH16-31 and OUTPUT (16-31) 5 Aeroflex Plainview Address Lines (A0 - A3) 4.0V 50% 0.8V 11.6V MIN 50% MUX Output 0V t AHL Definition of t AHL Address Lines (A0 - A3) 4.0V 50% 0.8V 11.6V MIN MUX Output 50% 0V t ALH Definition of t ALH 4.0V EN Lines 50% 0.8V ~3V to 12.5V MUX Output 50% 0V tONEN tOFFEN Definition of tONEN and tOFFEN NOTE: f = 10KHz, Duty cycle = 50%. ACT8518 SWITCHING DIAGRAMS SCD8518 Rev D 11/18/08 6 Aeroflex Plainview PIN NUMBERS & FUNCTIONS ACT8518 - 96 Leads Ceramic QUAD Flat Pack Pin # Function Pin # Function Pin # Function 1 A2 33 CH11 65 GND 2 B2 34 GND 66 GND 3 A3 35 CH12 67 NC 4 B3 36 GND 68 NC 5 EN 0-15 37 CH13 69 NC 6 NC 38 GND 70 Output V(16-31) 7 CH0 39 CH14 71 GND 8 GND 40 GND 72 GND 9 CH1 41 CH15 73 CH31 10 GND 42 GND 74 CH30 11 CH2 43 NC 75 CH29 12 GND 44 +VEE 76 CH28 13 CH3 45 NC 77 CH27 14 GND 46 -VEE 78 CH26 15 CH4 47 NC 79 CH25 16 GND 48 VREF 80 CH24 17 CH5 49 NC 81 CH23 18 GND 50 CASE GND 82 CH22 19 CH6 51 GND 83 CH21 20 GND 52 GND 84 CH20 21 CH7 53 GND 85 CH19 22 GND 54 GND 86 CH18 23 GND 55 GND 87 CH17 24 GND 56 GND 88 CH16 25 Output V(0-15) 57 GND 89 GND 26 NC 58 GND 90 GND 27 CH8 59 GND 91 NC 28 GND 60 GND 92 EN 16-31 29 CH9 61 GND 93 A0 30 GND 62 GND 94 B0 31 CH10 63 GND 95 A1 32 GND 64 GND 96 B1 NOTE: It is recommended that all "NC" or "no connect pin" be grounded. This eliminates or minimizes any ESD or static buildup. SCD8518 Rev D 11/18/08 7 Aeroflex Plainview ORDERING INFORMATION Model Number Screening DSCC SMD # Package ACT8518-S Military Temperature, -55C to +125C, Screened in accordance with MIL-PRF-38534, Class K NA QUAD Flat Pack ACT8518-7 Commercial Flow, +25C testing only ACT8518-201-1S In accordance with DSCC SMD FLAT PACKAGE OUTLINE 5962-0920401KXC 1.150 .005 (23 Spaces at .050) Tol Non-Cum 4 Sides Pin 1 Pin 12 .200 MAX Pin 85 Pin 84 Pin 13 .0165 .003 1.320 SQ MAX Pin 36 (.400) Pin 61 Pin 60 Pin 37 .006 .001 Note: Outside ceramic tie bars not shown for clarity. Contact factory for details. EXPORT CONTROL: EXPORT WARNING: This product is controlled for export under the International Traffic in Arms Regulations (ITAR). A license from the U.S. Department of State is required prior to the export of this product from the United States. Aeroflex's military and space products are controlled for export under the International Traffic in Arms Regulations (ITAR) and may not be sold or proposed or offered for sale to certain countries. (See ITAR 126.1 for complete information.) PLAINVIEW, NEW YORK Toll Free: 800-THE-1553 Fax: 516-694-6715 INTERNATIONAL Tel: 805-778-9229 Fax: 805-778-1980 NORTHEAST Tel: 603-888-3975 Fax: 603-888-4585 SE AND MID-ATLANTIC Tel: 321-951-4164 Fax: 321-951-4254 WEST COAST Tel: 949-362-2260 Fax: 949-362-2266 CENTRAL Tel: 719-594-8017 Fax: 719-594-8468 www.aeroflex.com info-ams@aeroflex.com Aeroflex Microelectronic Solutions reserves the right to change at any time without notice the specifications, design, function, or form of its products described herein. All parameters must be validated for each customer's application by engineering. No liability is assumed as a result of use of this product. No patent licenses are implied. SCD8518 Rev D 11/18/08 V Our passion for performance is defined by three attributes represented by these three icons: solution-minded, performance-driven and customer-focused 8