AMPLIMITE* HDP-20 and Economy 114-40030 Crimp Snap Subminiature D Commercial Connectors NOTE i Application Specification 19 DEC 08 Rev C All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2 . Figures and illustrations are for identification only and are not drawn to scale. _ 1. INTRODUCTION This specification covers the requirements for the application of AMPLIMITE HDP-20 and Economy Crimp Snap Subminiature D Commercial Connectors with all-plastic contact retention. These commercial connectors are available with or without shielding or shielding enclosure kits. Contacts are available in three snap-in types: crimp, posted, and solder cup. The crimp snap-in contacts are available with or without an insulation support barrel for strain relief. Refer to Application Specification 114-10000 for information on these HD-20 Precision Formed Contacts. Various accessories are compatible with the connectors and kits. Assembled connectors are designed to meet the requirements of Military Specification MIL-C-24308. AMPLIMITE HDP-20 Connectors come in a variety of sizes for your production needs and are adaptable to a variety of mounting and hardware requirements. Using a keystone mating face configuration, these connectors incorporate multiple polarization and mating alignment features, allowing flexibility in system design. The plug connector has an integral hood which protects the inserted pin contacts. The cavity rows are number-coded for your convenience. These connectors accept a contact with a wire size range of 28-18 AWG. When corresponding with Tyco Electronics Personnel, use the terminology provided on this specification to help facilitate your inquiry for information. Basic terms and features of components are provided in Figure 1. Optional Connector Grounding Shell Optional 4-40 Indents Clinch Nuts Pin Hood Keystone Mating Face Receptacle Housing (Accepts Socket Contacts) Plug Housing (Accepts Pin Contacts) Figure 1 2. Reference Material 2.1. Revision Summary This paragraph is reserved for a revision summary covering the most recent additions and changes made to this specification which include the following: S Updated document to corporate requirements S Deleted obsolete and added new documents to Paragraphs 2.5 and 2.6 S New logo and format E 2008 Tyco Electronics Corporation, Harrisburg, PA All International Rights Reserved TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change. PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service, TE logo and Tyco Electronics are trademarks. *Trademark. Other products, logos, and company names used are the property of their respective owners. visit our website at www.tycoelectronics.com 1 of 13 LOC B AMPLIMITE HDP-20 Subminiature D Connectors 114-40030 2.2. Customer Assistance Reference Part Number 205206 and Product Code 5091 are representative numbers of AMPLIMITE HDP-20 Subminiature D Commercial Connectors. Use of these numbers will identify the product line and expedite your inquiries through a service network established to help you obtain product and tooling information. Such information can be obtained through a local Tyco Electronics Representative or, after purchase, by calling the Tooling Assistance Center or the Product Information number at the bottom of page 1. 2.3. Drawings Customer Drawings for each product part number are available from the service network. The information contained in Customer Drawings takes priority if there is a conflict with this specification or with any technical documentation supplied by Tyco Electronics. 2.4. Manuals Manual 402-40 is available from the service network. This manual provides information on various flux types and characteristics along with the commercial designation and flux removal procedures. A checklist is included in the manual as required for information on soldering problems. 2.5. Specifications A. Product Specifications Product Specifications 108-40005, 108-40030, 108-40032 provide product performance requirements and test information. B. Application Specifications Application Specifications 114-10000, 114-25034, 114-40002, 114-40003, 114-40008, 114-40010, 114-40013, 114-40015, 114-40017, 114-40023, 114-40026, 114-40027, and 114-40028 contain design, inspection, and assembly procedures for AMPLIMITE HDP-20 Connectors. 2.6. Instructional Material The following list includes available instruction sheets (408-series) that provide assembly procedures for product, operation, maintenance and repair of tooling; and customer manuals (409-series) that provide setup, operation, and maintenance of machines. Document Number 408-4245 408-6551 408-6609 408-6769 408-6906 408-7514 408-7555 408-7799 408-7837 408-8083 408-9010 408-9128 408-9130 408-9131 408-9172 408-9199 408-9238 408-9242 408-9243 408-9315 408-9318 408-9404 2 of 13 Document Title Seating Fixture Assembly 543615-1 for AMPLIMITE HDP Series One-Piece Shield Slide Latch Kits and Locking Post Kits AMPLIMITE HD-20 Shielded Cable Clamp Kits AMPLIMITE HDP-20, HDP-22, and HDE-20 Right-Angle Metal Shielded Cable Clamp Kits Release Tool Kit 91266-2 for AMPLIMITE Connector Cable Clamps AMPLIMITE High Density (HDP-20) Connectors with Crimp-Type Contacts Cable Clamp Assemblies for AMPLIMITE HD-20 and HD-22 Connectors AMPLIMITE Solder Pot contacts (66569-3 and 66570-3) Female Screwlock Kits and Male Screw Retainer Kits Ferrule Applicator Assembly No. 812407-1 Shielding Hardware Kits for AMPLIMITE HDP-20 and HDE-20 Connectors AMPLIMITE Latching Blocks AMPLIMITE Two-Piece Spring Latches for Straight Exit RFI/EMI Cable Clamps, Straight/90 Degree Exit Two-Piece Cable Clamps, and Universal Cable Clamps Two-Piece Spring Latches for AMPLIMITE Connectors Used with Post Molded Strain Relief Shielding Hardware Enclosure Kits for AMPLIMITE Connectors Shielding Enclosure Expansion Tool Kits 58241-1, -2, and -4 Universal Cable Clamp Kits for AMPLIMITE Connectors Die Assemblies 58237-1 and 58237-2 Crimping Die Assembly 58238-1 for AMPLIMITE Connectors Hand Crimping Tool 543344-1 Crimping Die Assemblies 543013-[ ] Insertion/Extraction Tool 91285-1 and Replacement Tip Kits 543382 Tyco Electronics Corporation Rev C AMPLIMITE HDP-20 Subminiature D Connectors Document Number 408-9507 408-9508 408-9721 409-5842 409-5843 114-40030 Document Title Crimping Die Assemblies 543424-1 Through -8 for AMPLIMITE Connectors Crimping Die Assemblies 543425-1 and 543425-2 for AMPLIMITE Connectors Die Holder Assemblies 58449-1, -2, and -3 AMP-O-LECTRIC* Model "G" Terminating Machine 354500-[ ] 2700-Lb. Pneumatic Power Unit 312522-[ ] 3. REQUIREMENTS 3.1. Storage A. Ultraviolet Light Prolonged exposure to ultraviolet light may deteriorate the chemical composition used in housings. B. Shelf Life The connectors should remain in the shipping containers until ready for use to prevent damage to the housings. The products should be used on a first in, first out basis to avoid storage contamination that could adversely affect signal transmissions. C. Chemical Exposure Do not store housings near any chemicals listed below, as they may cause stress corrosion cracking in the components. Alkalies Amines Ammonia NOTE Carbonates Citrates Nitrites Phosphates Citrates Sulfides Nitrites Sulfur Compounds Tartrates Where the above environmental conditions exist, phosphor-bronze contacts are recommended instead of brass if available. i 3.2. Mounting Panel Cutout AMPLIMITE HDP-20 Connectors are adaptable to rack-and-panel applications. We recommend mounting the plug to the panel and the receptacle to the rack. Figure 2 provides panel cutout, mating, and mounting clearance dimensions. NOTE Dimensions H and J apply when using cable clamps or latching blocks. Connectors with floating bushings are for use in drawer applications, or other difficult alignment situations. i G Dia (2 Holes A C D _ + 2_ A Per Cutout) 10 F (2 Places) F J E H K Radius G + 0.05 [.002] (4 Places) Dia (2 Places) 6.60 [.260] Min Clearance Between Connectors B 7. 06 .278 1.02 [.040] 6.30 Dia (Typ) Mating Cutout for Rear .248 Clearance Mount and Short Plug Latching Blocks Receptacle 3.28 + 0.05 [.129 + .002] Rev C Figure 2 (cont'd) Tyco Electronics Corporation 3 of 13 AMPLIMITE HDP-20 Subminiature D Connectors CONNECTOR POSITIONS OS O S AND SHELL SIZE PANEL MTG POSN FLOATING BUSHING 114-40030 DIMENSIONS + 0.05 [.002] A B C Yes D E F G 23.01 11.51 13.84 6.93 2.24 [.906] [.453] [.545] [.273] [.088] HD JD --- --2.11 Front 9 Position No 24.99 12.50 [.984] [.492] Yes Size 1 22.20 11.10 13.03 6.53 3.05 [.874] [.437] [.513] [.257] [.120] 21.29 10.64 12.22 6.12 2.24 [.838] [.419] [.481] [.241] [.088] [.083] --- --- --- --3.35 Rear No Yes 20.47 10.24 11.40 5.72 3.05 13.97 19.05 [.806] [.403] [.449] [.225] [.120] [.550] [.750] --- --- 31.34 15.67 13.84 6.93 2.24 [1.234] [.617] [.545] [.273] [.088] 30.53 15.27 13.03 6.53 3.05 No 33.32 16.66 [1.202] [.601] [.513] [.257] [.120] [1.312] [.656] Yes Size 2 [.083] --- --- --- --- 29.62 14.81 12.22 6.12 2.24 [1.166] [.583] [.481] [.241] [.088] 28.80 14.40 11.40 5.72 3.05 18.54 19.05 [1.134] [.567] [.449] [.225] [.120] [.730] [.750] --- --- 3.35 Rear No Yes 45.08 22.56 13.84 6.93 2.24 [1.775] [.888] [.545] [.273] [.088] 44.27 22.15 13.03 6.53 3.05 No 47.04 23.52 [1.743] [.872] [.513] [.257] [.120] [1.852] [.926] Yes Size 3 [.083] --- --- --- --- 43.33 21.67 12.22 6.12 2.24 [1.706] [.853] [.481] [.241] [.088] 42.52 21.26 11.40 5.72 3.05 32.38 19.05 [1.674] [.837] [.449] [.225] [.120] [1.275] [.750] 61.54 30.78 13.84 6.93 2.24 --- --- [2.423] [1.212] [.545] [.273] [.088] 3.35 Rear No Yes No 63.50 31.75 [2.500] [1.250] Yes Size 4 60.73 30.38 13.03 6.53 3.05 [2.391] [1.196] [.513] [.257] [.120] 59.79 29.90 12.22 6.12 2.24 [2.354] [1.177] [.481] [.241] [.088] [.083] --- --- --- --3.35 Rear No Yes 59.08 29.54 11.40 5.72 3.05 48.77 19.05 [2.326] [1.163] [.449] [.225] [.120] [1.920] [.750] 59.16 29.59 16.64 8.33 2.24 --- --- [2.329] [1.165] [.655] [.328] [.088] No 61.11 30.56 [2.406] [1.203] Yes Size 5 58.34 29.18 15.82 7.92 3.05 [2.297] [1.149] [.623] [.312] [.120] 57.15 28.58 14.91 7.47 2.24 [2.250] [1.125] [.587] [.587] [.088] [.083] --- --- --- --3.35 Rear No D [.132] 2.11 Front 50 Position [.132] 2.11 Front 37 Position [.132] 2.11 Front 25 Position [.132] 2.11 Front 15 Position K 56.34 28.17 14.10 7.06 3.05 43.64 19.05 [2.218] [1.109] [.555] [.278] [.120] [1.718] [.750] [.132] Dimensions H and J apply when using cable clamps or latching blocks. Connectors with floating bushings are for use in drawer applications, or other difficult alignment situations. Figure 2 (end) 4 of 13 Tyco Electronics Corporation Rev C AMPLIMITE HDP-20 Subminiature D Connectors 114-40030 3.3. Contact Insertion Terminated contacts are inserted into the back of the connector housing, and snap in place. The cavity rows are numbered for your convenience. If your design does not require the use of all cavities, the contacts should be distributed evenly throughout the connector. NOTE After inserting a contact into the housing, pull back lightly on the wire to make sure the contact is fully seated. i 3.4. Terminated Strip Length Terminated strip length shall be as indicated in Figure 3. TERMINATED STRIP LENGTH CONTACT POSN 9 15 25 37 50 B" LENGTH Terminated Strip Length B + 1.27 [.050] Connector Ferrule 33.02 [1.300] 39.12 [1.540] 38.1 [1.500] Braid Figure 3 3.5. Ferrule Crimp Requirements Slide the ferrule onto the cable prior to stripping the cable. Keep the larger diameter end of the ferrule toward the end to be terminated. If the ferrule has only one diameter, no orientation is required. After the wires and contacts have been terminated slide the ferrule until it is over the braid. Crimp the braid according to the instructions packaged with the appropriate tooling. See Figure 4 for ferrule crimp requirements. NOTE Trim excess braid flush with front of ferrule with a knife. i 1.02 [.040] Max TERMINATED ASSY LENGTH CONTACT POSN 9 15 25 37 50 D F" LENGTH E 38.99 [1.535] 48.06 [1.892] 47.65 [1.876] E Section D-D B Max D C 0.38 [.015] Max A Section E-E F + 0.64 [.025] Figure 4 (cont'd) Rev C Tyco Electronics Corporation 5 of 13 AMPLIMITE HDP-20 Subminiature D Connectors 114-40030 CABLE DIAMETER ACCEPTED CABLE CRIMP A" CABLE CRIMP B" 4.19-4.83 [.165-.190] 4.5 + 0.13 [.177 + .005] 10.21 [.402] 4.83-5.51 [.190-.217] 5.41 + 0.13 [.213 + .005] 9.58 [.377] 5.51-6.25 [.217-.246] 6.07 + 0.13 [.239 + .005] --- 6.25-7.21 [.246-.284] 6.68 + 0.13 [.263 + .005] 10.85 [.427] 7.21-8.23 [.284-.324] 7.65 + 0.13 [.301 + .005] --- 8.23-9.52 [.324-.375] 8.66 + 0.13 [.341 + .005] --- 9.52-11.10 [.375-.437] 9.98 + 0.13 [.393 + .005] --- 10.16-11.56 [.400-.455] 10.49 + 0.13 [.413 + .005] --- 5.84-6.73 [.230-.265] 6.43 + 0.2 [.253 + .008] --- 8.58-9.78 [.338-.385] 9.14 + 0.2 [.360 + .008] 11.84 [.466] 9.52-10.97 [.375-.432] 10.16 + 0.2 [.400 + .008] 12.95 [.510] 10.72-12.45 [.422-.490] 10.72 + 0.2 [.422 + .008] 16.00 [.630] 12.19-14.27 [.480-.562] 12.19 + 0.2 [.480 + .008] 16.00 [.630] SHIELD CRIMP C" 10.9 + 0.13 [.429 + .005] 13.72 + 0.2 [.540 + .008] Figure 4 (end) 3.6. Hardware and Accessories The AMPLIMITE HDP-20 Connectors are compatible with the mounting hardware and accessories as shown in Figure 5. The instructional material listed (in parentheses) with each accessory provides details for product selection and assembly procedures. A. Shielding Hardware Kits Shielding Hardware Kits (Instruction Sheet 408-9010) and Shielding Hardware Enclosure Kits (Instruction Sheet 408-9172) are available for AMPLIMITE connectors. Hardware kits include a connector and inner and outer shield halves. Enclosure kits also include a protective flexible thermoplastic enclosure and two male jackscrews. The thermoplastic enclosure is assembled to the kit using Shielding Enclosure Expansion Tools with base PN 58241 (Instruction Sheet 408-9199). Cable ferrules must be purchased separately. B. Cable Clamp Assembly Kits Cable clamp assembly kits are available in straight/45_ and straight/90_ versions (Instruction Sheet 408-7555). The clamp assemblies can be mated using spring latches (Instruction Sheets 408-9130, 408-9131) and latching blocks (Instruction Sheet 408-9128), or using screwlocks and retainers (Instruction Sheet 408-7837). C. Shielded Cable Clamp Assembly Kits Metal RFI/EMI Shielded Cable Clamp Assemblies come in two-piece kits, and are available in both straight-exit (Instruction Sheet 408-6609) and 90_-exit (Instruction Sheet 408-6769) versions. Unlike the hardware kits, these cable clamp kits allow the cable to be fully prepared and terminated to the connector before shield installation. The straight-exit shield is attached to the connector using saddle washers and screws. The 90_-exit shield is attached using slide latches and screws. D. Jacketed Shielded Cable For applications using jacketed shielded cable with AMPLIMITE shields (see subparagraph C), two ferrule options are available. As split-ring ferrule is used with a foil or braided shield and is not crimped. An inner and an outer crimped ferrule are used with applications using braid-shielded cable only. E. Slide Latch Assemblies and Clips One-Piece Slide Latch or Two-Piece Slide Latch Clips (Instruction Sheet 408-6551) attach to the connector mating face. The mating connector uses Locking Post Assemblies which latch into the slide latch assembly. 6 of 13 Tyco Electronics Corporation Rev C AMPLIMITE HDP-20 Subminiature D Connectors 114-40030 F. Universal Cable Clamp Kits Universal Cable Clamp Kits (Instruction Sheet 408-9238) are available for connectors with a number 3 shell size (25 position) only. Each kit consists of two cable clamp halves, a two-piece braid termination clamp set (shielded versions only), a cable clamp wedge set, and mounting screws. Release Tool Kit 91266-2 (Instruction Sheet 408-6906) is used to release assembled universal cable clamp halves. G. One Piece Economy Shielding Hardware AMPLIMITE One-Piece Economy Shielding Hardware is available for AMPLIMITE Size 1, 2, and 3 connectors. These press-on hardware shields must be seated with Seating Fixture 543615-1 (Instruction Sheet 408-4245). The shielding hardware is copper with tin overplating and is available in straight 90_ exit versions only. Ferrule (Ref) and Shield Ferrule (Ref) Connector Shell Halves Hidden From View Outer Shield Half Thermoplastic Enclosure Inner Shield Half Contacts (Ref) Jackscrew (2) Shielding Hardware Kit Shielding Hardware Ferrule (Ref) Enclosure Kit Ferrule (Ref) One Piece Economy Shielding Hardware (Size 1) Connector Shell Connector One Piece Economy Shell Shielding Hardware (Size 2) Ferrule (Ref) One Piece Economy Shielding Hardware (Size 3) Figure 5 (cont'd) Rev C Tyco Electronics Corporation 7 of 13 AMPLIMITE HDP-20 Subminiature D Connectors 114-40030 Screw (3) Receptacle (Ref) Plug Spring (Ref) Latch (2) Cable Clamp Assembly _ Cable Clamp Straight 90 Assembly Kit (Assembled) Latching Block (2) M3 Metric Screw (2) Cable Clamp Assembly with Screwlocks and Retainers Female Screwlock (2) Flat Washer (4) Retainer Lock Washer (2) Screw (2) Hex Nut (2) Retainer (2) Assembled Screwlock (Ref) 4-40 Fillister Head Two-Piece Shield Screws and Hex 4-40 Pan Head Nuts (2 Each) 4-40 Saddle Screws (3) Screw (2) Connector One-Piece Connector 4-40 Slide-Latch Slide Latch Screw (2) _ Exit RFI/EMI Shielded Straight Exit RFI/EMI Shielded 90 Cable Clamp Assembly Kit Cable Clamp Assembly Kit Figure 5 (cont'd) 8 of 13 Tyco Electronics Corporation Rev C AMPLIMITE HDP-20 Subminiature D Connectors Crimp Ferrules for Braided Cable Shield Flared Cable Braid Jacket 114-40030 Outer Ferrule Inner Ferrule Conductors Split-Ring Foil or Braid Split-Ring Ferrules or Foil or Braided Cable Shield Cable Jacket Ferrule (To be Folded Back Over Two-Piece Slide Latch Assembly Kit Ferrule and Ground Wire) 4-40 Screw (2) Conductors Ground Wire One-Piece Slide Latch Assembly Kit J 4-40 Hex One-Piece Slide Nut (2) Flat Slide Latch Latch (2) Washer 4-40 Screw (2) (2) Lockwasher (2) Typical Slide Latch Application Flat Washer (2) Mounting 4-40 Screw (2) Lockwasher (2) Hex Nut Wedge Set (2) Locking Post Assembly Kit Lockwasher (2) 4-40 Hex Nut (2) Braid Termination 4-40 Locking Shim (Ref - Use Between Post (2) Panel and Connector Flange Clamp Set when Front Mounted) Cable Clamp Flat Washer (4) J Universal Cable Clamp Kit Half (2) One-piece slide latches for shell sizes 1, 4, and 5 cannot be used with cable clamps that extend beyond the front of the connector flange. Figure 5 (end) Rev C Tyco Electronics Corporation 9 of 13 AMPLIMITE HDP-20 Subminiature D Connectors 114-40030 3.7. Repair Use Insertion/Extraction Tool 91285-1 (Instruction Sheet 408-9404) to remove individual contacts from housings for replacement or for relocation to another housing cavity. Damaged or worn contacts may be replaced provided there is sufficient slack, after restripping the wire, to insert the new contact. CAUTION DO NOT re-use damaged or worn contacts. Instead, replace them with new contacts and discard the old ones. ! 4. QUALIFICATION AMPLIMITE HDP-20 Subminiature D Commercial Connectors are Listed by Underwriters Laboratories Inc. (UL) in File Number E-28476 and Certified by CSA International in File Number LR-16455. These connector assemblies will also mate with any size 20 Subminiature D complying with the dimensions in Military Standard MIL-C-24308. 5. TOOLING AMPLIMITE HDP-20 Connector ferrules can be terminated to wire using hand, semi-automatic, or automatic crimping tools. Recommended tooling, and instructional material, is provided in Figures 6 and 7. AMPLIMITE HDP Series One-Piece Shield can be applied by using Seating Fixture 543615-1. The seating fixture assembly is designed to fully seat a one-piece shield for an RFI/EMI shielded AMPLIMITE HDP Connector Assembly for customer-applied overmolding. Refer to Instruction Sheet 408-4245 for specific instructions on this application. 5.1. Braid Shielded Cable Inner and outer crimp ferrules, used with braid-shielded cable only, are crimped with the tooling listed in the table in Figure 6. These arrangements are able to stand alone, or may be used with a variety of shielded and unshielded cable clamps. The dies listed in this table must be inserted into corresponding tooling. Hand tool dies 543013-[ ] (Instruction Sheet 408-9318) fit Hand Crimping Tool 543344-1 (Instruction Sheet 408-9315), while applicator dies (no publication) fit Ferrule Applicator Assembly 812407-1 (Instruction Sheet 408-8083). The applicator is powered by the AMP-O-LECTRIC Model "G" Terminating Machine 354500-[ ] (Customer Manual 409-5842). The exact cable clamp used determines inner ferrule size and shape. The inner ferrule, in turn, determines the dies. Some ferrules are stepped, and some straight; some stepped ferrules have a large flared end, some a smaller flare. These differences are noted in the table. CONNECTOR CABLE INNER OR CABLE CLAMP DIAMETER FERRULE SHELL SIZE ACCEPTED TYPE (SIZE) 9 Position Size 1 HAND TOOL DIE SET HAND TOOL DIE SET MARKING APPLICATOR DIE SET Stepped 543013-2 B-1 Straight 543013-1 A-1 5.84-7.11 [.230-.280] Stepped 1-543013-7 B-8 813809-7 8.13-9.40 [.320-.370] Straight 543013-6 B-3 813809-5 Stepped (Large) 543013-3 C-1 Stepped (Small) 543013-2 B-1 4 83 6 10 [.190-.240] 4.83-6.10 [ 190 240] 813809 1 813809-1 4 83 6 10 [.190-.240] 4.83-6.10 [ 190 240] 813809 1 813809-1 15 Position 5.84-7.11 [.230-.280] Stepped 1-543013-6 C-8 813809-7 Size 2 7.62-8.89 [.300-.350] Stepped 543013-4 C-2 813809-2 8.00-9.27 [.315-.365] Straight 543013-6 B-3 813809-5 9.65-10.92 [.380-.430] Straight 543013-7 C-4 813809-3 Figure 6 (cont'd) 10 of 13 Tyco Electronics Corporation Rev C AMPLIMITE HDP-20 Subminiature D Connectors 114-40030 CONNECTOR CABLE INNER OR CABLE CLAMP DIAMETER FERRULE SHELL SIZE ACCEPTED TYPE (SIZE) 4.83-6.10 [.190-.240] Stepped 543013-3 C-1 813809-1 5.84-7.11 [.230-.280] Stepped 1-543013-6 C-8 813809-7 Stepped (Small) 543013-4 C-2 Stepped (Large) 543013-5 D-2 Straight 543013-7 C-4 Stepped 543013-8 D-4 11.94-13.46 [.470-.530] Straight 1-543013-0 D-5 813809-4 4.83-6.10 [.190-.240] Stepped 543013-3 C-1 813809-1 5.84-7.11 [.230-.280] Stepped 1-543013-6 C-8 813809-7 7.62-8.89 [.300-.350] Stepped 543013-4 C-2 813809-2 Straight 543013-7 C-4 Stepped 543013-9 E-4 12.06-13.34 [.475-.525] Stepped 1-543013-1 E-5 813809-4 14.99-16.51 [.590-.650] Straight 1-543013-3 E-6 4.83-6.10 [.190-.240] Stepped 543013-2 B-1 813809-1 7.62-8.89 [.300-.350] Stepped 543013-5 D-2 813809-2 8.00-9.27 [.315-.365] Straight 543013-6 B-3 813809-5 9.65-10.92 [.380-.430] Stepped 543013-8 D-4 813809-3 Straight 1-543013-0 D-5 Stepped 1-543013-2 F-5 15.24-16.51 [.600-.650] Stepped 1-543013-4 F-6 17.78-19.05 [.700-.750] Straight 1-543013-5 F-7 813809-8 25 Position HAND TOOL DIE SET HAND TOOL DIE SET MARKING 7 62 8 89 [.300-.350] 7.62-8.89 [ 300 350] Size Si 3 APPLICATOR DIE SET 813809 2 813809-2 9 65 10 92 [[.380-.430] 9.65-10.92 380 430] 813809 3 813809-3 37 Position Si Size 4 50 Position 9 65 10 92 [[.380-.430] 9.65-10.92 380 430] Size 5 813809 3 813809-3 11 94 13 46 [.470-.530] 11.94-13.46 [ 470 530] 813809 4 813809-4 Ferrule Crimp Tooling s Applicator 812407-1 Die 543013-[ ] Hand Tool 543344-1 s Use with Die Set 813809 and Machine 354500-1 Figure 6 (cont'd) Rev C Tyco Electronics Corporation 11 of 13 AMPLIMITE HDP-20 Subminiature D Connectors 114-40030 Miscellaneous Tooling Insertion/Extraction Tool 91285-1 Shielding Enclosure Expansion Tool 58241-[ ] Seating Fixture Assembly 543615-1 Figure 6 (end) 5.2. Single Cable-to-Shield Ferrules The dies listed in the table in Figure 7 must be inserted into the hand tools and automatic machine die holder that uses them. Die sets with base PN 58237 (Instruction Sheet 408-9242) and 58238 (Instruction Sheet 408-9243) are used in Hand Crimping Tool 543344-1 (Instruction Sheet 408-9315), or in Die Holder 58449-1 (Instruction Sheet 408-9721) powered by Pneumatic Power Unit 312522-3 (Customer Manual 409-5843). Die sets with base PN 543424 (Instruction Sheet 408-9507) and 543425 (Instruction Sheet 408-9508) are used in Hand Crimping Tool 543344-1 (Instruction Sheet 408-9315) only. NOTE i Crimp dimensions for ferrules will fall within proper guidelines when dies are seated in the appropriate tooling and properly gaged. Gaging information is contained in instruction sheets corresponding to the dies. All braided cable shielding should be folded forward and distributed evenly before sliding and crimping the ferrule into place. HARDWARE SHELL SIZE CABLE DIAMETER ACCEPTED DIE SET 1, 2, 3 4.19-4.83 [.165-.190] 543424-3 4.83-5.51 [.190-.217] 543424-2 5.51-6.25 [.217-.246] 543424-8 6.25-7.21 [.246-.284] 543424-1 7.21-8.23 [.284-.324] 543424-7 8.23-9.52 [.324-.375] 543424-6 9.52-11.10 [.375-.437] 543424-5 10.16-11.56 [.400-.455] 543424-4 5.84-6.73 [.230-.265] 543425-2 8.58-9.78 [.338-.385] 543425-1 9.52-10.97 [.375-.432] 58238-1 10.72-12.45 [.422-.490] 58237-2 12.19-14.27 [.480-.562] 58237-1 4, 5 Typical Die Assembly Figure 7 12 of 13 Tyco Electronics Corporation Rev C AMPLIMITE HDP-20 Subminiature D Connectors 114-40030 6. VISUAL AID Figure 8 shows a typical application of an AMPLIMITE HDP-20 Subminiature D Commercial Connector with Snap-In Contacts. This illustration should be used by production personnel to ensure a correctly applied product. Applications which DO NOT appear correct should be inspected using the information in the preceding pages of this specification and in the instructional material shipped with the product or tooling. MATING CONNECTOR ASSEMBLIES MUST MATCH IN BOTH SHELL SIZE AND NUMBER OF POSITIONS PULL LIGHTLY ON EACH INDIVIDUAL WIRE TO BE SURE THAT CONTACTS ARE FULLY SEATED AND LOCKED IN PLACE HARDWARE AND ACCESSORIES MATCHED PROPERLY FOR MATING AND SECURELY IN PLACE CONNECTOR MUST BE UNDAMAGED BY ASSEMBLY AND TIGHTENING OF HARDWARE KIT OR ACCESSORIES TYPICAL APPLICATION (SHOWS FREE-HANGING CONNECTORS WITH LOCKING POSTS AND SLIDE LATCHES) FIGURE 8. VISUAL AID Rev C Tyco Electronics Corporation 13 of 13