High Performance, 4-/8-Channel,
Fault-Protected Analog Multiplexers
ADG438F/ADG439F
Rev. E
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ©2011 Analog Devices, Inc. All rights reserved.
FEATURES
All switches off with power supply off
Analog output of on channel clamped within power supplies
if an overvoltage occurs
Latch-up proof construction
Fast switching times
tON 250 ns maximum
tOFF 150 ns maximum
Fault and overvoltage protection: −40 V to +55 V
Break-before-make construction
TTL- and CMOS-compatible inputs
APPLICATIONS
Data acquisition systems
Industrial and process control systems
Avionics test equipment
Signal routing between systems
High reliability control systems
GENERAL DESCRIPTION
The ADG438F and ADG439F are CMOS analog multiplexers, with
the ADG438F comprising eight single channels and the ADG439F
comprising four differential channels. These multiplexers provide
fault protection. Using a series n-channel, p-channel, and
n-channel MOSFET structure, both device and signal source
protection is provided in the event of an overvoltage or power
loss. The multiplexer can withstand continuous overvoltage
inputs from −40 V to +55 V. During fault conditions with power
supplies off, the multiplexer input (or output) appears as an open
circuit and only a few nanoamperes of leakage current flows. This
protects not only the multiplexer and the circuitry driven by the
multiplexer, but also protects the sensors or signal sources which
drive the multiplexer.
The ADG438F switches one of eight inputs to a common output
as determined by the 3-bit binary address lines, A0, A1, and A2.
The ADG439F switches one of four differential inputs to a
common differential output as determined by the 2-bit binary
address lines, A0 and A1. An EN input on each device is used
to enable or disable the device. When disabled, all channels are
switched off.
FUNCTIONAL BLOCK DIAGRAM
S1
S8
A0
D
ADG438F
A1 A2 EN
1 OF 8
DECODER
00468-001
Figure 1.
S1A
A0
DA
ADG439F
A1
S4A
S1B
S4B
DB
EN
1 OF 4
DECODER
00468-101
Figure 2.
PRODUCT HIGHLIGHTS
1. Fault Protection. The ADG438F and ADG439F can with-
stand continuous voltage inputs up to −40 V or +55 V.
When a fault occurs due to the power supplies being
turned off, all the channels are turned off and only a
leakage current of a few nanoamperes flows.
2. On channel saturates while fault exists.
3. Low RON.
4. Fast Switching Times.
5. Break-Before-Make Switching. Switches are guaranteed
break-before-make so that input signals are protected
against momentary shorting.
6. Trench Isolation Eliminates Latch-Up. A dielectric trench
separates the p-channel and n-channel MOSFETs thereby
preventing latch-up.
7. Improved Off Isolation. Trench isolation enhances the
channel-to-channel isolation of the ADG438F/ADG439F.
ADG438F/ADG439F
Rev. E | Page 2 of 16
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications....................................................................................... 1
General Description......................................................................... 1
Functional Block Diagram .............................................................. 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Dual Supply ................................................................................... 3
Absolute Maximum Ratings............................................................ 5
ESD Caution...................................................................................5
Pin Configuration and Function Descriptions..............................6
Typical Performance Characteristics ..............................................7
Test Circuits........................................................................................9
Terminology .................................................................................... 12
Theory of Operation ...................................................................... 13
Outline Dimensions....................................................................... 14
Ordering Guide .......................................................................... 15
REVISION HISTORY
7/11—Rev. D to Rev. E
Updated Format..................................................................Universal
Changes to Product Highlights Section and General
Description ........................................................................................ 1
Changes to Specification Section and Table 1 .............................. 3
Changes to Table 2............................................................................ 5
Added Table 3 and Table 4; Renumbered Sequentially ............... 6
Changes to Figure 5 to Figure 10.................................................... 7
Changes to Figure 11 to Figure 13.................................................. 8
Added Figure 14 to Figure 16.......................................................... 8
Changes to Figure 18 to Figure 20, Figure 23, and Figure 24 ..... 9
Changes to Terminology Section.................................................. 12
Changes to Theory of Operation Section, Figure 29, and
Figure 30 .......................................................................................... 13
Updated Outline Dimensions....................................................... 14
Changes to Ordering Guide .......................................................... 15
2/00—Rev. C to Rev. D
ADG438F/ADG439F
Rev. E | Page 3 of 16
SPECIFICATIONS
DUAL SUPPLY
VDD = +15 V ± 10%, VSS = −15 V ± 10%, GND = 0 V, unless otherwise noted.
Table 1.
B Version
Parameter +25°C
−40°C to
+85°C
−40°C to
+105°C
−40°C to
+125°C Unit Test Conditions/Comments
ANALOG SWITCH
Analog Signal Range VSS + 1.4 V typ Output open circuit
V
DD − 1.4 V typ
V
SS + 2.2 V typ Output loaded, 1 mA
V
DD – 2.2 V typ
RON 270 Ω typ −10 V VS ≤ +10 V, IS = 1 mA
390 420 450 Ω max See Figure 17
On-Resistance Flatness, RFLAT (ON) 9 % typ −10 V VS ≤ +10 V, IS = 1 mA
10 10 10 10 % max
RON Drift 0.6 %/°C typ VS = 0 V, IS = 1 mA
On-Resistance Match Between
Channels, ΔRON
3 3 3 3 % max VS = ±10 V, IS = 1 mA
LEAKAGE CURRENTS
Source Off Leakage, IS (Off) ±0.01 nA typ
VD = ±10 V, VS = 10 V
m
±0.5 ±1.5 ±1.5 ±4 nA max See Figure 18
Drain Off Leakage, ID (Off) ±0.01 nA typ
VD = ±10 V, VS = 10 V
m
ADG438F ADG439F ±0.5 ±5 ±5 ±20 nA max See Figure 19
Channel On Leakage, ID, IS (On) ±0.01 nA typ VS = VD = ± 10 V
ADG438F/ADG439F ±0.5 ±5 ±5 ±20 nA max See Figure 20
FAULT
Source Leakage Current, IS (Fault) ±0.02 nA typ
VS = +55 V or −40 V, VD = 0 V;
see Figure 21
(With Overvoltage) ±0.05 ±0.1 ±0.2 ±0.2 μA max
Drain Leakage Current, ID (Fault) ±0.05 nA typ
VS = ±25 V, VD = 10 V; see
mFigure 19
(With Overvoltage) ±0.05 ±0.1 ±0.2 ±0.2 μA max
Source Leakage Current, IS (Fault)
(Power Supplies Off)
±30 nA typ VS = ±25 V, VD = VEN, A0, A1, A2 = 0 V
±0.1 ±0.2 ±0.3 1 μA max See Figure 22
DIGITAL INPUTS
Input High Voltage, VINH 2.4 2.4 2.4 V min
Input Low Voltage, VINL 0.8 0.8 0.8 V max
Input Current
IINL or IINH ±1 ±1 ±1 μA max VIN = 0 V or VDD
Digital Input Capacitance, CIN 5 pF typ
DYNAMIC CHARACTERISTICS1
tTRANSITION 175 ns typ RL = 1 MΩ, CL = 35 pF
220 300 300 330 ns max
VS1 = ±10 V, VS8 = m10 V; see Figure 25
tOPEN 90
60 40 40 40 ns min
RL = 1 kΩ, CL = 35 pF, VS = 5 V;
see Figure 26
tON (EN) 180 ns typ RL = 1 kΩ, CL = 35 pF
230 300 300 345 ns max VS = 5 V; see Figure 27
tOFF (EN) 100 ns typ RL = 1 kΩ, CL = 35 pF
130 150 150 173 ns max VS = 5 V; see Figure 27
ADG438F/ADG439F
Rev. E | Page 4 of 16
B Version
Parameter +25°C
−40°C to
+85°C
−40°C to
+105°C
−40°C to
+125°C Unit Test Conditions/Comments
Settling Time, tSETT
0.1% 1 1 1 μs typ RL = 1 kΩ, CL = 35 pF
0.01% 2.5 2.5 2.5 μs typ VS = 5 V
Charge Injection 15 pC typ
VS = 0 V, RS = 0 Ω, CL = 1 nF;
see Figure 28
Off Isolation 93 dB typ
RL = 1 kΩ, CL = 15 pF, f = 100 kHz,
VS = 7 V rms; see Figure 23
Channel-to-Channel Crosstalk 93 dB typ
RL = 1 kΩ, CL = 15 pF, f = 100 kHz,
VS = 7 rms; see Figure 24
CS (Off) 3 pF typ
CD (Off)
ADG438F 22 pF typ
ADG439F 12 pF typ
POWER REQUIREMENTS
IDD 0.05 mA typ VIN = 0 V or 5 V
0.1 0.2 0.2 0.2 mA max
ISS 0.1 μA typ
1 1 1 μA max
1 Guaranteed by design, not subject to production test.
ADG438F/ADG439F
Rev. E | Page 5 of 16
ABSOLUTE MAXIMUM RATINGS
TA = 25°C unless otherwise noted.
Table 2.
Parameter Rating
VDD to VSS 48 V
VDD to GND −0.3 V to +48 V
VSS to GND +0.3 V to −48 V
Digital Input, EN, Ax −0.3 V to VDD + 0.3 V or 20 mA,
whichever occurs first
VS, Analog Input Overvoltage with
Power On (VDD = +15 V, VSS = −15 V)
VSS − 25 V to VDD + 40 V
VS, Analog Input Overvoltage with
Power Off (VDD = 0 V, VSS = 0 V)
−40 V to +55 V
Continuous Current, S or D 20 mA
Peak Current, S or D (Pulsed at 1 ms,
10% Duty Cycle Maximum)
40 mA
Operating Temperature Range
Industrial (B Version) −40°C to +125°C
Storage Temperature Range −65°C to +150°C
Junction Temperature 150°C
Plastic DIP Package
θJA, Thermal Impedance 117°C/W
SOIC Package
θJA, Thermal Impedance
Narrow Body 125°C/W
Wide Body 90°C/W
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
ADG438F/ADG439F
Rev. E | Page 6 of 16
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
A0
1
EN
2
V
SS 3
S1
4
A1
16
A2
15
GND
14
V
DD
13
S2
5
S3
6
S4
7
S5
12
S6
11
S7
10
D
8
S8
9
ADG438F
TOP VIEW
(Not to Scale)
00468-004
Figure 3. ADG438F Pin Configuration
Table 3. ADG438F Pin Function Description
Pin
No. Mnemonic Description
1 A0 Logic Control Input.
2 EN Active High Digital Input. When low, the
device is disabled, and all switches are off.
When high, Ax logic inputs determine on
switches.
3 VSS Most Negative Power Supply Potential. In
single-supply applications, this pin can be
connected to ground.
4 S1 Source Terminal 1. This pin can be an input
or an output.
5 S2 Source Terminal 2. This pin can be an input
or an output.
6 S3 Source Terminal 3. This pin can be an input
or an output.
7 S4 Source Terminal 4. This pin can be an input
or an output.
8 D Drain Terminal. This pin can be an input or
an output.
9 S8 Source Terminal 8. This pin can be an input
or an output.
10 S7 Source Terminal 7. This pin can be an input
or an output.
11 S6 Source Terminal 6. This pin can be an input
or an output.
12 S5 Source Terminal 5. This pin can be an input
or an output.
13 VDD Most Positive Power Supply Potential.
14 GND Ground (0 V) Reference.
15 A2 Logic Control Input.
16 A1 Logic Control Input.
A0
1
EN
2
V
SS 3
S1A
4
A1
16
GND
15
V
DD
14
S1B
13
S2A
5
S3A
6
S4A
7
S2B
12
S3B
11
S4B
10
DA
8
DB
9
ADG439F
TOP VIEW
(Not to Scale)
00468-005
Figure 4. ADG439F Pin Configuration
Table 4. ADG439F Pin Function Description
Pin
No. Mnemonic Description
1 A0 Logic Control Input.
2 EN Active High Digital Input. When low, the
device is disabled, and all switches are off.
When high, Ax logic inputs determine on
switches.
3 VSS Most Negative Power Supply Potential. In
single-supply applications, this pin can be
connected to ground.
4 S1A Source Terminal 1A. This pin can be an
input or an output.
5 S2A Source Terminal 2A. This pin can be an
input or an output.
6 S3A Source Terminal 3A. This pin can be an
input or an output.
7 S4A Source Terminal 4A. This pin can be an
input or an output.
8 DA Drain Terminal A. This pin can be an input
or an output.
9 DB Drain Terminal B. This pin can be an input
or an output.
10 S4B Source Terminal 4B. This pin can be an
input or an output.
11 S3B Source Terminal 3B. This pin can be an
input or an output.
12 S2B Source Terminal 2B. This pin can be an
input or an output.
13 S1B Source Terminal 1B. This pin can be an
input or an output.
14 VDD Most Positive Power Supply Potential.
15 GND Ground (0 V) Reference.
16 A1 Logic Control Input.
Table 5. ADG438F Truth Table1
A2 A1 A0 EN On Switch
X X X 0 None
0 0 0 1 1
0 0 1 1 2
0 1 0 1 3
0 1 1 1 4
1 0 0 1 5
1 0 1 1 6
1 1 0 1 7
1 1 1 1 8
1 X = don’t care.
Table 6. ADG439F Truth Table1
A1 A0 EN On Switch Pair
X X 0 None
0 0 1 1
0 1 1 2
1 0 1 3
1 1 1 4
1 X = don’t care.
ADG438F/ADG439F
Rev. E | Page 7 of 16
TYPICAL PERFORMANCE CHARACTERISTICS
2000
1000
0
15–15 –10 –5 0 5 10
500
1750
1500
1250
750
250
V
D
, V
S
(V)
R
ON
()
T
A
= 25°C
V
DD
= +5V
V
SS
= –5V
V
DD
= +10V
V
SS
= –10V
V
DD
= +15V
V
SS
= –15V
00468-008
Figure 5. On Resistance as a Function of VD (VS)
1
m
1p
–50 –30 –20 –10 0 10 20 30 40 50 60
–40
1n
100µ
10µ
10n
100n
10p
100p
V
S
SOURCE VOLTAGE (V)
I
S
INPUT LEAKAGE (A)
OPERATING RANGE
V
DD
= 0V
V
SS
= 0V
V
D
= 0V
00468-009
Figure 6. Source Input Leakage Current as a Function of VS (Power Supplies Off)
During Overvoltage Conditions
1
m
1p
–50 –30 –20 –10 0 10 20 30 40 50 60
–40
1n
100µ
10µ
10n
100n
10p
100p
V
S
SOURCE VOLTAGE (V)
I
D
INPUT LEAKAGE (A)
OPERATING RANGE
V
DD
= +15V
V
SS
= –15V
V
D
= 0V
00468-010
Figure 7. Drain Output Leakage Current as a Function of VS (Power Supplies On)
During Overvoltage Conditions
2000
1000
0
15–15 –10 –5 0 5 10
500
1750
1500
1250
750
250
V
D
, V
S
(V)
R
ON
()
V
DD
= +15V
V
SS
= –15V
T
A
= 125°C
T
A
= 105°C
T
A
= 85°C
T
A
= 25°C
00468-011
Figure 8. On Resistance as a Function of VD (VS) for Different Temperatures
1
m
1p
–50 –30 –20 10 0 10 20 30 40 50 60
–40
1n
100µ
10µ
10n
100n
10p
100p
V
S
SOURCE VOLTAGE (V)
I
S
INPUT LEAKAGE (A)
OPERATING RANGE
V
DD
= +15V
V
SS
= –15V
V
D
= 0V
00468-012
Figure 9. Source Input Leakage Current as a Function of VS (Power Supplies On)
During Overvoltage Conditions
0.3
0.2
–0.3
–14 –10 –6 –2 2 6 10 14
0.1
0.0
–0.2
–0.1
V
S
,V
D
(V)
LEAKAGE CURRENTS (nA)
I
D
(OFF)
I
S
(OFF)
I
D
, I
S
(ON)
V
DD
= +15V
V
SS
= –15V
V
S
(V
D
) = ±10V
T
A
= 25°C
00468-013
Figure 10. Leakage Currents as a Function of VD (VS)
ADG438F/ADG439F
Rev. E | Page 8 of 16
100
10
0.01
45 5525 65 75 85 95 10535
1
115 125
0.1
TEMPERATURE (°C)
LEAKAGE CURRENTS (nA)
V
DD
= +15V
V
SS
= –15V
V
D
= +10V
V
S
= –10V
I
S
(OFF)
I
D
(ON)
I
D
(OFF)
00468-014
Figure 11. Leakage Currents as a Function of Temperature
260
240
100
10 11 12 13 14 15
120
t
ON
(EN)
220
200
180
160
140
SWITCHING TIME (ns)
POWER SUPPLY (V)
t
TRANSITION
t
OFF
(EN)
00468-015
Figure 12. Switching Time vs. Dual Power Supply
300
0
–40 20 0 20 40 60 80 100 120
50
250
200
150
100
TEMPERATURE (°C)
SWITCHING TIME (ns)
t
TRANSITION
t
ON
(EN)
t
OFF
(EN)
V
DD
= +15V
V
SS
= –15V
00468-016
Figure 13. Switching Time vs. Temperature
–120
–100
–80
–60
–40
–20
0
OFF ISOL
A
TION (dB)
FREQUENCY (Hz)
10k 100k 1M 10M 100M 1G1k
TA = 25°C
VDD = +15V
VSS = –15V
00468-113
Figure 14. Off Isolation vs. Frequency, ±15 V Dual Supply
0
5
10
15
20
25
30
35
40
–15 –10 –5 0 5 10 15
PIN C
A
PACITANCE (pF)
V
S
(V)
T
A
= 25°C
V
DD
= +15V
V
SS
= –15V
DRAIN OFF
SOURCE OFF
00468-114
Figure 15. Capacitance vs. Source Voltage
–30
–20
–10
0
10
20
30
–15 –10 –5 0 5 10 15
QINJ (pC)
VS (V)
VDD = +15V
VSS = –15V
TA = 25°C
00468-115
Figure 16. Charge Injection vs. Source Voltage
ADG438F/ADG439F
Rev. E | Page 9 of 16
TEST CIRCUITS
I
DS
S
R
ON
= V
1
/I
DS
V1
V
S
D
00468-021
Figure 17. On Resistance
S1
S2
S8
V
D
I
S
(OFF)
V
S
V
DD
V
SS
V
DD
V
SS
D
0.8VEN
A
00468-022
Figure 18. IS (Off)
S1
S2
S8
V
S
I
D
(OFF)
V
D
V
DD
V
SS
V
DD
V
SS
D
0.8VEN
A
00468-023
Figure 19. ID (Off)
SD
A
V
D
I
D
(ON)
NC
NC = NO CONNECT
00468-025
Figure 20. ID (On)
S1
S2
S8
V
SVD
VDD VSS
V
DD
V
SS
D
0.8VEN
A
00468-026
Figure 21. Input Leakage Current (with Overvoltage)
A2
0
V
0
V
VDD VSS
VS
D
0V
A1
A0
EN
GND
ADG438F*
S1
S8
A
*SIMILAR CONNECTION FOR ADG439F.
00468-027
Figure 22. Input Leakage Current (with Power Supplies Off)
V
IN
A2
V
DD
V
DD
D
V
SS
V
SS
A1
A0
GND
ADG438F*
S1
S8
*SIMILAR CONNECTION FOR ADG439F.
V
OUT
R
L
50
00468-034
Figure 23. Off Isolation
CHANNEL-TO-CHANNEL CROSSTALK = 20 log V
OUT
GND
S1
D
S2
V
OUT
NETWORK
ANALYZER
R
L
50
R
50
V
S
V
S
V
DD
V
SS
0.1µF
V
DD
0.1µF
V
SS
00468-200
Figure 24. Channel-to-Channel Crosstalk
ADG438F/ADG439F
Rev. E | Page 10 of 16
A2
D
V
S1
V
IN
V
S8
V
OUT
A1
A0
EN
GND
ADG438F*
S1
S8
S2 TO S7
2.4V
50
V
SS
V
DD
V
SS
V
DD
*SIMILAR CONNECTION FOR ADG439F.
3V
50%
V
OUT
t
TRANSITION
t
TRANSITION
90%
90%
ADDRESS
DRIVE (V
IN
)50%
C
L
35pF
R
L
1M
00468-024
Figure 25. Switching Time of Multiplexer, tTRANSITION
A2
D
V
S
V
IN
V
OUT
A1
A0
EN
GND
ADG438F*
S1
S8
S2 TO S7
2.4V
50
3V
V
OUT
t
OPEN
80% 80%
**SIMILAR CONNECTION FOR ADG439F.
V
SS
V
DD
V
SS
V
DD
C
L
35pF
R
L
1k
ADDRESS
DRIVE (V
IN
)
00468-029
Figure 26. Break-Before-Make Delay, tOPEN
A2
D
V
S
V
OUT
A1
A0
EN
GND
ADG438F*
S1
S2 TO S8
R
L
1k
50C
L
35pF
V
SS
V
DD
V
SS
V
DD
3V
0V
0V
V
OUT
OUTPUT
t
ON
(EN)
t
OFF
(EN)
50%50%
0.9V
OUT
0.1V
OUT
*SIMILAR CONNECTION FOR ADG439F.
V
IN
ENABLE
DRIVE (V
IN
)
00468-030
Figure 27. Enable Delay, tON (EN), tOFF (EN)
ADG438F/ADG439F
Rev. E | Page 11 of 16
3V
V
OUT
LOGIC
INPUT (V
IN
)
Q
INJ
= C
L
× V
OUT
0V
A2
V
OUT
D
*SIMILAR CONNECTION FOR ADG439F.
A1
A0
EN
GND
ADG438F*
S
C
L
1nF
V
S
V
SS
V
SS
V
DD
V
DD
V
IN
R
S
V
OUT
00468-033
Figure 28. Charge Injection
ADG438F/ADG439F
Rev. E | Page 12 of 16
TERMINOLOGY
VDD
Most positive power supply potential.
VSS
Most negative power supply potential.
GND
Ground (0 V) reference.
RON
Ohmic resistance between D and S.
ΔRON
ΔRON represents the difference between the RON of any two
channels as a percentage of the maximum RON of those two
channels.
RFLAT (ON)
Flatness is defined as the difference between the maximum and
minimum value of the on resistance measured over the specified
analog signal range and is represented by RFLAT (ON).
Flatness is calculated by
((RMAXRMIN) / RMAX × 100)
RON Drift
Change in RON when temperature changes by one degree Celsius.
IS (Off)
Source leakage current when the switch is off.
ID (Off)
Drain leakage current when the switch is off.
ID, IS (On)
Channel leakage current when the switch is on.
VD (VS)
Analog voltage on Terminal D and Terminal S.
IS (Fault—Power Supplies On)
Source leakage current when exposed to an overvoltage
condition.
ID (Fault—Power Supplies On)
Drain leakage current when exposed to an overvoltage
condition.
IS (Fault—Power Supplies Off)
Source leakage current with power supplies off.
CS (Off)
Channel input capacitance for off condition.
CD (Off)
Channel output capacitance for off condition.
CD, CS (On)
On switch capacitance.
CIN
Digital input capacitance.
tON (EN)
Delay time between the 50% and 90% points of the digital input
and switch on condition.
tOFF (EN)
Delay time between the 50% and 90% points of the digital input
and switch off condition.
tTRANSITION
Delay time between the 50% and 90% points of the digital
inputs and the switch on condition when switching from one
address state to another.
tOPEN
Off time measured between 80% points of both switches when
switching from one address state to another.
VINL
Maximum input voltage for Logic 0.
VINH
Minimum input voltage for Logic 1.
IINL (IINH)
Input current of the digital input.
Off Isolation
A measure of unwanted signal coupling through an off channel.
Charge Injection
A measure of the glitch impulse transferred from the digital
input to the analog output during switching.
IDD
Positive supply current.
ISS
Negative supply current.
ADG438F/ADG439F
Rev. E | Page 13 of 16
THEORY OF OPERATION
The ADG438F/ADG439F multiplexers are capable of withstanding
overvoltages from −40 V to +55 V, irrespective of whether the
power supplies are present or not. Each channel of the multiplexer
consists of an n-channel MOSFET, a p-channel MOSFET, and
an n-channel MOSFET, connected in series. When the analog
input exceeds the power supplies, one of the MOSFETs saturates,
limiting the current. The current during a fault condition is
determined by the load on the output. Figure 31 illustrates the
channel architecture that enables these multiplexers to with-
stand continuous overvoltages.
When an analog input of VSS + 2.2 V to VDD – 2.2 V (output loaded,
1 mA) is applied to the ADG438F/ADG439F, the multiplexer
behaves as a standard multiplexer, with specifications similar to
a standard multiplexer, for example, the on-resistance is 270 Ω
typically. However, when an overvoltage is applied to the device,
one of the three MOSFETs saturates.
Figure 29 to Figure 32 show the conditions of the three
MOSFETs for the various overvoltage situations. When the
analog input applied to an on channel approaches the positive
power supply line, the n-channel MOSFET saturates because
the voltage on the analog input exceeds the difference between
VDD and the n-channel threshold voltage (VTN). When a voltage
more negative than VSS is applied to the multiplexer, the p-channel
MOSFET saturates because the analog input is more negative
than the difference between VSS and the p-channel threshold
voltage (VTP). Because VTN is nominally 1.4 V and VTP − 1.4 V,
the analog input range to the multiplexer is limited to VSS + 1.4 V
to VDD − 1.4 V (output open circuit) when a ±15 V power supply
is used.
When the power supplies are present but the channel is off, again
either the p-channel MOSFET or one of the n-channel MOSFETs
remains off when an overvoltage occurs.
Finally, when the power supplies are off, the gate of each MOSFET
is at ground. A negative overvoltage switches on the first n-channel
MOSFET, but the bias produced by the overvoltage causes the
p-channel MOSFET to remain turned off. With a positive over-
voltage, the first MOSFET in the series remains off because the
gate to source voltage applied to this MOSFET is negative.
During fault conditions (power supplies off), the leakage current
into and out of the ADG438F/ADG439F is limited to a few
microamps. This limit protects the multiplexer and succeeding
circuitry from over stresses as well as protects the signal sources
that drive the multiplexer. Also, the other channels of the multi-
plexer are undisturbed by the overvoltage and continue to operate
normally.
Q1 Q2 Q3
+55V
OVERVOLTAGE
n-CHANNEL
MOSFET
SATURATES
V
DD
V
SS
00468-017
Figure 29. +55 V Overvoltage Input to the On Channel
Q1 Q2 Q3
–40V
OVERVOLTAGE
n-CHANNEL
MOSFET
IS ON p-CHANNEL
MOSFET
SATURATES
V
SS
V
DD
00468-018
Figure 30. −40 V Overvoltage on an Off Channel with Multiplexer Power On
Q1 Q2 Q3
+55V
OVERVOLTAGE
n-CHANNEL
MOSFET IS
OFF
00468-019
Figure 31. +55 V Overvoltage with Power Off
Q1 Q2 Q3
–40V
OVERVOLTAG E
n-CHANNEL
MOSFET IS
ON p-CHANNEL
MOSFET IS
OFF
00468-020
Figure 32. –40 V Overvoltage with Power Off
ADG438F/ADG439F
Rev. E | Page 14 of 16
OUTLINE DIMENSIONS
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
COMPLIANT TO JEDEC STANDARDS MS-001-AB
073106-B
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
16
18
9
0.100 (2.54)
BSC
0.800 (20.32)
0.790 (20.07)
0.780 (19.81)
0.210 (5.33)
MAX
SEATING
PLANE
0.015
(0.38)
MIN
0.005 (0.13)
MIN
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
0.060 (1.52)
MAX
0.430 (10.92)
MAX
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.015 (0.38)
GAUGE
PLANE
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
Figure 33. 16-Lead Plastic Dual In-Line Package [PDIP]
Narrow Body
(N-16)
Dimensions shown in inches and (millimeters)
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
COMPLIANT TO JEDEC STANDARDS MS-012-AC
10.00 (0.3937)
9.80 (0.3858)
16 9
8
1
6.20 (0.2441)
5.80 (0.2283)
4.00 (0.1575)
3.80 (0.1496)
1.27 (0.0500)
BSC
SEATING
PLANE
0.25 (0.0098)
0.10 (0.0039)
0.51 (0.0201)
0.31 (0.0122)
1.75 (0.0689)
1.35 (0.0531)
0.50 (0.0197)
0.25 (0.0098)
1.27 (0.0500)
0.40 (0.0157)
0.25 (0.0098)
0.17 (0.0067)
COPLANARITY
0.10
060606-A
45°
Figure 34. 16-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-16)
Dimensions shown in millimeters and (inches)
ADG438F/ADG439F
Rev. E | Page 15 of 16
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
COMPLIANT TO JEDEC STANDARDS MS-013-AA
10.50 (0.4134)
10.10 (0.3976)
0.30 (0.0118)
0.10 (0.0039)
2.65 (0.1043)
2.35 (0.0925)
10.65 (0.4193)
10.00 (0.3937)
7.60 (0.2992)
7.40 (0.2913)
0.75(0.0295)
0.25(0.0098)
45°
1.27 (0.0500)
0.40 (0.0157)
C
OPLANARITY
0.10 0.33 (0.0130)
0.20 (0.0079)
0.51 (0.0201)
0.31 (0.0122)
SEATING
PLANE
16 9
8
1
1.27 (0.0500)
BSC
03-27-2007-B
Figure 35. 16-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-16)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model1 Temperature Range Package Description Package Option
ADG438FBN −40°C to +125°C 16-Lead Plastic Dual In-Line Package [PDIP] N-16
ADG438FBNZ −40°C to +125°C 16-Lead Plastic Dual In-Line Package [PDIP] N-16
ADG438FBR −40°C to +125°C 16-Lead Standard Small Outline Package [SOIC_N] R-16
ADG438FBR-REEL −40°C to +125°C 16-Lead Standard Small Outline Package [SOIC_N] R-16
ADG438FBRZ −40°C to +125°C 16-Lead Standard Small Outline Package [SOIC_N] R-16
ADG438FBRZ-REEL −40°C to +125°C 16-Lead Standard Small Outline Package [SOIC_N] R-16
ADG439FBN −40°C to +125°C 16-Lead Plastic Dual In-Line Package [PDIP] N-16
ADG439FBNZ −40°C to +125°C 16-Lead Plastic Dual In-Line Package [PDIP] N-16
ADG439FBR −40°C to +125°C 16-Lead Standard Small Outline Package [SOIC_N] R-16
ADG439FBR-REEL −40°C to +125°C 16-Lead Standard Small Outline Package [SOIC_N] R-16
ADG439FBRW −40°C to +125°C 16-Lead Standard Small Outline Package [SOIC_W] RW-16
ADG439FBRWZ −40°C to +125°C 16-Lead Standard Small Outline Package [SOIC_W] RW-16
ADG439FBRWZ-REEL −40°C to +125°C 16-Lead Standard Small Outline Package [SOIC_W] RW-16
ADG439FBRZ −40°C to +125°C 16-Lead Standard Small Outline Package [SOIC_N] R-16
ADG439FBRZ-REEL −40°C to +125°C 16-Lead Standard Small Outline Package [SOIC_N] R-16
1 Z = RoHS Compliant Part.
ADG438F/ADG439F
Rev. E | Page 16 of 16
NOTES
©2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D00468-0-7/11(E)