INTEGRATED CIRCUITS DATA SHEET For a complete data sheet, please also download: * The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications * The IC06 74HC/HCT/HCU/HCMOS Logic Package Information * The IC06 74HC/HCT/HCU/HCMOS Logic Package Outlines 74HC/HCT4059 Programmable divide-by-n counter Product specification Supersedes data of September 1993 File under Integrated Circuits, IC06 1998 Jul 08 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 In the divide-by-n mode, a clock cycle wide pulse is generated with a frequency rate equal to the input frequency divided by n. FEATURES * Synchronous programmable divide-by-n counter * Presettable down counter The function of the mode select and JAM inputs are illustrated in the following examples. In the divide-by-2 mode, only one flip-flop is needed in the first counting section. Therefore the last (5th) counting section has three flip-flops that can be preset to a maximum count of seven with a place value of thousands. This counting mode is selected when Ka to Kc are set HIGH. In this case input J1 is used to preset the first counting section and J2 to J4 are used to preset the last (5th) counting section. * Fully static operation * Mode select control of initial decade counting function (divide-by-10, 8, 5, 4 and 2) * Master preset initialization * Latchable output * Easily cascadable with other counters * Four operating modes: timer divider-by-n divide-by-10 000 master preset If the divide-by-10 mode is desired for the first section, Ka and Kb are set HIGH and Kc is set LOW. The JAM inputs J1 to J4 are used to preset the first counting section (there is no last counting section). The intermediate counting section consists of three cascaded BCD decade (divide-by-10) counters, presettable by means of the JAM inputs J5 to J16. * Output capability: standard * ICC category: MSI The preset of the counter to a desired divide-by-n is achieved as follows: GENERAL DESCRIPTION The 74HC/HCT4059 are high-speed Si-gate CMOS devices and are pin compatible with the "4059" of the "4000B" series. They are specified in compliance with JEDEC standard no. 7A. n = (MODE(1)) (1 000 x decade 5 preset + 100 x decade 4 preset + 10 x decade 3 preset + 1 x decade 2 preset) + decade 1 preset The 74HC/HCT4059 are divide-by-n counters which can be programmed to divide an input frequency by any number (n) from 3 to 15 999. There are four operating modes, timer, divide-by-n, divide-by-10 000 and master preset, which are defined by the mode select inputs (Ka to Kc) and the latch enable input (LE) as shown in the Function table. To calculate preset values for any "n" count, divide the "n" count by the selected mode. The resultant is the corresponding preset value of the 5th to the 2nd decade with the remainder being equal to the 1st decade value; preset value = n/mode. If n = 8 479, and the selected mode = 5, the preset value = 8 479/5 = 1 695 with a remainder of 4, thus the JAM inputs must be set as shown in Table 1. The complete counter consists of a first counting stage, an intermediate counting stage and a fifth counting stage. The first counter stage consists of four independent flip-flops. Depending on the divide-by-mode, at least one flip-flop is placed at the input of the intermediate stage (the remaining flip-flops are placed at the fifth stage with a place value of thousands). The intermediate stage consists of three cascaded decade counters, each containing four flip-flops. To verify the results, use the given equation: n = 5 (1 000 x 1 + 100 x 6 + 10 x 9 + 1 x 5) + 4 n = 8 479. If n = 12 382 and the selected mode = 8, the preset value = 12 382/8 = 1 547 with a remainder of 6, thus the JAM inputs must be set as shown in Table 2. All flip-flops can be preset to a desired state by means of the JAM inputs (J1 to J16), during which the clock input (CP) will cause all stages to count from n to zero. The zero-detect circuit will then cause all stages to return to the JAM count, during which an output pulse is generated. In the timer mode, after an output pulse is generated, the output pulse remains HIGH until the latch input (LE) goes LOW. The counter will advance, even if LE is HIGH and the output is latched in the HIGH state. 1998 Jul 08 To verify: n = 8 (1 000 x 1 + 100 x 5 + 10 x 4 + 1 x 7) + 6 n = 12 382. (1) MODE = first counting section divider (10, 8, 5, 4 or 2). 2 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 If n = 8 479 and the selected mode = 10, the preset value = 8 479/10 with a remainder of 9, thus the JAM inputs must be set as shown in Table 3. Control inputs Kb and Kc can be used to initiate and lock the counter in the "master preset" mode. In this condition the flip-flops in the counter are preset in accordance with the JAM inputs and the counter remains in that mode as long as Kb and Kc both remain LOW. The counter begins to count down from the preset state when a counting mode other than the "master preset" mode is selected. Whenever the "master preset" mode is used, control signals Kb = Kc = LOW must be applied for at least 2 full clock pulses. After the "master preset" mode inputs have been changed to one of the counting modes, the next positive-going clock transition changes an internal flip-flop so that the count-down begins on the second positive-going clock transition. Thus, after a "master preset" mode, there is always one extra count before the output goes HIGH. Figure 6 illustrates the operation of the counter in the divide-by-8 mode starting from the preset state 3. To verify: n = 10 (1 000 x 0 + 100 x 8 + 10 x 4 + 1 x 7) + 9 n = 8 479. The three decades of the intermediate counting section can be preset to a binary 15 instead of a BCD 9. In this case the first cycle of a counter consists of 15 count pulses, the next cycles consisting of 10 counting pulses. Thus the place value of the three decades are still 1, 10 and 100. For example, in the divide-by-8 mode, the number from which the intermediate counting section begins to count-down can be preset to: 3rd decade: 1 500 2nd decade: 150 1st decade: 15 If the "master preset" mode is started two clock cycles or less before an output pulse, the output pulse will appear at the correct moment. When the output pulse appears and the "master preset" mode is not selected, the counter is preset according to the states of the JAM inputs. The last counting section can be preset to a maximum of 1, with a place value of 1 000. The first counting section can be preset to a maximum of 7. To calculate n: n = 8 (1 000 x 1 + 100 x 15 + 10 x 15 + 1 x 15) + 7 When Ka, Kb, Kc and LE are LOW, the counter operates in the "preset inhibit" mode, during which the counter divides at a fixed rate of 10 000, independent of the state of the JAM inputs. However, the first cycle length after leaving the "master preset" mode is determined by the JAM inputs. n = 21 327. 21 327 is the maximum possible count in the divide-by-8 mode. The highest count of the various modes is shown in the Function table, in the column entitled "binary counter range". When Ka, Kb and Kc are LOW and input LE = HIGH, the counter operates in the normal divide-by-10 mode, however, without the latch operation at the output. The mode select inputs permit, when used with decimal programming, a non-BCD least significant digit. For example, the channel spacing in a radio is 12.5 kHz, it may be convenient to program the counter in decimal steps of 100 kHz subdivided into 8 steps of 12.5 kHz controlled by the least significant digit. Also frequency synthesizer channel separations of 10, 12.5, 20, 25 and 50 parts can be chosen by the mode select inputs. This is called "Fractional extension". A similar extension called "Half channel offset" can be obtained in modes 2, 4, 6 and 8, if the JAM inputs are switched between zero and 1, 2, 3 and 4 respectfully. This is illustrated in Fig.5. This device is particularly advantageous in digital frequency synthesizer circuits (VHF, UHF, FM, AM etc.) for communication systems, where programmable divide-by-"n" counters are an integral part of the synthesizer phase-locked-loop sub-system. The 74HC/HCT4059 can also be used to perform the synthesizer "fixed divide-by-n" counting function, as well as general purpose counting for instrumentation functions such as totalizers, production counters and "time out" timers. This feature is used primarily in cases where radio channels are allocated according to the following formula: Schmitt-trigger action at the clock input makes the circuit highly tolerant to slower clock rise and fall times. Channel frequency = channel spacing x (N + 0.5) N is an integer. 1998 Jul 08 3 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 QUICK REFERENCE DATA GND = 0 V; Tamb = 25 C; tr = tf = 6 ns SYMBOL PARAMETER CONDITIONS TYPICAL HC UNIT HCT tPHL/ tPLH propagation delay CP to Q CL = 15 pF; VCC = 5 V 18 20 ns fmax maximum clock frequency 40 40 MHz CI input capacitance 3.5 3.5 pF CPD power dissipation capacitance per package 30 32 pF notes 1 and 2 Notes 1. CPD is used to determine the dynamic power dissipation (PD in W): PD = CPD x VCC2 x fi + (CL x VCC2 x fo) where: fi = input frequency in MHz fo = output frequency in MHz (CL x VCC2 x fo) = sum of outputs CL = output load capacitance in pF VCC = supply voltage in V 2. For HC the condition is VI = GND to VCC For HCT the condition is VI = GND to VCC - 1.5 V ORDERING INFORMATION TYPE NUMBER PACKAGE NAME DESCRIPTION VERSION 74HC4059N3; 74HCT4059N3 DIP24 plastic dual in-line package; 24 leads (300 mil) SOT222-1 74HC4059N; 74HCT4059N DIP24 plastic dual in-line package; 24 leads (600 mil) SOT101-1 74HC4059D; 74HCT4059D SO24 plastic small outline package; 24 leads; body width 7.5 mm SOT137-1 1998 Jul 08 4 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 PIN DESCRIPTION PIN NO. SYMBOL NAME AND FUNCTION 1 CP clock input (LOW-to-HIGH, edge-triggered) 2 LE latch enable (active HIGH) 3, 4, 5, 6, 22, 21, 20, 19, 18, 17, 16, 15, 10, 9, 8, 7 J1 to J16 programmable JAM inputs (BCD) 12 GND ground (0 V) 14, 13, 11 Ka to Kc mode select inputs 23 Q divide-by-n output 24 VCC positive supply voltage Fig.1 Pin configuration. 1998 Jul 08 Fig.2 Logic symbol. 5 Fig.3 IEC logic symbol. Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 APPLICATIONS * Frequency synthesizer, ideally suited for use with PC74HC/HCT4046A, PC74HC/HCT7046A and PC74HC/HCT9046A (PLLs) * Fixed or programmable frequency division * "Time out" timer Fig.4 Functional block diagram. 1998 Jul 08 6 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 FUNCTION TABLE LATCH ENABLE INPUT MODE SELECT INPUTS FIRST COUNTING SECTION DECADE 1 LAST COUNTING SECTION DECADE 5 COUNTER RANGE OPERATION LE Ka Kb Kc MODE MAX JAM PRESET INPUTS STATE USED H H 1 H H 2 MAX. JAM DIVIDED PRESET INPUTS BY STATE USED BCD MAX. J1 8 7 J2J3J4 15 999 17 331 15 999 18 663 BINARY MAX. H L H H 4 3 J1J2 4 3 J3J4 H H L H 5 4 J1J2J3 2 1 J4 9 999 13 329 H L L H 8 7 J1J2J3 2 1 J4 15 999 21 327 H H H L 10 9 J1J2J3J4 1 0 - L H H H 2 1 J1 8 7 J2J3J4 15 999 17 331 L L H H 4 3 J1J2 4 3 J3J4 15 999 18 663 L H L H 5 4 J1J2J3 2 1 J4 9 999 13 329 L L L H 8 7 J1J2J3 2 1 J4 15 999 21 327 L H H L 10 9 J1J2J3J4 1 0 - 9 999 16 659 H L H L 10 9 J1J2J3J4 1 0 - 9 999 16 659 L L H L preset inhibited preset inhibited X X L L master preset master preset timer mode 9 999 16 659 divide-by-n mode fixed - 10 000 divide-by-10 000 mode - master preset mode - Note 1. It is recommended that the device is in the master preset mode (Kb = Kc = logic 0) in order to correctly initialize the device prior to start-up. An example of a suitable external circuit is shown in Fig.14. H = HIGH voltage level L = LOW voltage level X = don't care Table 1 4 1 5 9 6 J1 J2 J3 J4 J5 J6 J7 J8 J9 J10 J11 J12 J13 J14 J15 J16 L L H H H L H L H L L H L H H L Table 2 6 1 7 4 5 J1 J2 J3 J4 J5 J6 J7 J8 J9 J10 J11 J12 J13 J14 J15 J16 L H H H H H H L L L H L H L H L Table 3 9 7 4 8 J1 J2 J3 J4 J5 J6 J7 J8 J9 J10 J11 J12 J13 J14 J15 J16 H L L H H H H L L L H L L L L H 1998 Jul 08 7 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 Fig.5 Half channel offset. Fig.6 Total count of 3. 1998 Jul 08 8 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 DC CHARACTERISTIC FOR 74HC For the DC characteristics see "74HC/HCT/HCU/HCMOS Logic Family Specifications". Output capability: standard ICC category: MSI AC CHARACTERISTICS FOR 74HC GND = 0 V; tr = tf = 6 ns; CL = 50 pF Tamb (C) TEST CONDITIONS 74HC SYMBOL PARAMETER +25 -40 to +85 -40 to +125 UNIT VCC (V) WAVEFORMS 2.0 Fig.7 min. typ. max. min. max. min. max. tPHL/ tPLH tPHL/ tPLH tTHL/ tTLH tW trem fmax propagation delay CP to Q propagation delay LE to Q output transition time clock pulse width CP removal time Kb, Kc to CP maximum clock pulse frequency 58 200 250 300 21 40 50 60 4.5 17 34 43 51 6.0 50 175 220 265 18 35 44 53 4.5 14 30 37 45 6.0 19 75 95 110 7 15 19 22 4.5 6 13 16 19 6.0 ns ns 2.0 7 115 135 18 6 23 27 4.5 15 5 90 23 6.0 75 19 95 110 15 7 19 22 4.5 13 6 16 19 6.0 4.2 12 3.4 2.8 21 36 17 14 4.5 25 43 20 17 6.0 1. From master preset mode to any other mode. 9 ns 2.0 90 Note 1998 Jul 08 ns ns MHz 2.0 2.0 2.0 Fig.8 Fig.7 Fig.7 Fig.9; note 1 Fig.7 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 DC CHARACTERISTICS FOR 74HCT For the DC characteristics see "74HC/HCT/HCU/HCMOS Logic Family Specifications". Output capability: standard ICC category: MSI Note to HCT types The value of additional quiescent supply current (ICC) for a unit load of 1 is given in the family specifications. To determine ICC per input, multiply this value by the unit load coefficient shown in the table below. INPUT UNIT LOAD COEFFICIENT CP 0.65 LE 0.65 Jn 0.50 Ka 1.00 Kb 1.50 Kc 0.85 AC CHARACTERISTICS FOR 74HCT GND = 0 V; tr = tf = 6 ns; CL = 50 pF Tamb (C) TEST CONDITIONS 74HCT SYMBOL PARAMETER +25 -40 to +85 -40 to +125 UNIT VCC (V) WAVEFORMS min. typ. max. min. max. min. max. tPHL/ tPLH propagation delay CP to Q 24 46 58 69 ns 4.5 Fig.7 tPHL/ tPLH propagation delay LE to Q 24 46 58 69 ns 4.5 Fig.8 tTHL/ tTLH output transition time 7 15 19 22 ns 4.5 Fig.7 tW clock pulse width CP 20 7 25 30 ns 4.5 Fig.7 trem removal time Kb, Kc to CP 15 7 9 22 ns 4.5 Fig.9; note 1 fmax maximum clock pulse frequency 21 36 17 14 MHz 4.5 Fig.7 Note 1. From master preset mode to any other mode. 1998 Jul 08 10 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 AC WAVEFORMS (1) HC: VM = 50%; VI = GND to VCC. HCT: VM = 1.3 V; VI = GND to 3 V. Fig.7 (1) Waveforms showing the clock (CP) to output (Q) propagation delays, the clock pulse width, the output transition times and the maximum clock frequency. HC: VM = 50%; VI = GND to VCC. HCT: VM = 1.3 V; VI = GND to 3 V. Fig.8 Waveforms showing the LE input to Q output propagation delay. (1) HC: VM = 50%; VI = GND to VCC. HCT: VM = 1.3 V; VI = GND to 3 V. Fig.9 Waveforms showing the Kb or Kc removal times, when the operating mode is switched from master preset to any other mode. 1998 Jul 08 11 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 APPLICATION INFORMATION Fig.10 Example showing the application of the PC74HC/HCT4059 in a phase-locked-loop (PLL) for a FM band synthesizer. Figure 11 shows a BCD switch compatible arrangement suitable for divide-by-5 and divide-by-8 modes, which can be adapted (with minimal changes) to the other divide-by-modes. In order to be able to preset to any number from 3 to 256 000, while preserving the BCD switch compatible character of the JAM inputs, a rather complex cascading scheme is necessary because the "4059" can never be preset to count less than 3. Logic circuitry is required to detect a condition where one of the numbers to be preset in the "4059" is < 3. In order to simplify the detection logic, only that condition is detected where the JAM inputs to terminals 6, 7 and 9 would be LOW during one count. If such a condition is detected, and if at least 1 is expected to be jammed into the MSB counter, the detection logic removes one from the number to be jammed into the MSB counter (with a place value of 2 000 times the divide-by-mode) and jams the same 2 000 into the "4059" by forcing pins 6, 7 and 9 HIGH. Calculating the minimum and maximum divide-by-n values: Output frequency range = 87.6 to 103.8 MHz (CCIR band 2) Channel spacing frequency (fc) = 300 kHz Division factor prescaler (k) = 10 f 300 Reference frequency (fr) = ---c- = ---------- = 30 kHz k 10 103.8 MHz Maximum divide-by-n value = ----------------------------- = 346 300 kHz 87.6 MHz Minimum divide-by-n value = ------------------------- = 292 300 kHz 3 MHz Fixed divide-by-n value = ------------------ = 100 30 kHz The general circuit in Fig.11 can be simplified considerably if the range of the cascaded counters do not start at a very low value. Application of the "4059" as divide-by-n counter allows programming of the channel spacing (shown in equations as 300 kHz). A channel in the CCIR band 2 is selected by the divide-by-n counter as follows: Figure 12 shows an arrangement in the divide-by-4 mode, where the counting range extends in a BCD switch compatible manner from 99 003 to 114 999. channel = n - 290 1998 Jul 08 12 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 The arrangement shown in Fig.12 is easy to follow; once during every cycle the programmed digits are jammed in (15 616 in this example) and then a round number of 11 000 is jammed in, nine times in succession, by forcing the JAM inputs via AND/OR gates. In Fig.13 the divide-by-n sub-system is preset once to a number which represents the least significant digits of the divide-by number (15 690 in the example shown in Fig.13). The sub-system is then preset twice to a round number (8 000 in the example shown in Fig.13) and multiplied by the number of the divide-by mode (2 in the example shown in Fig.13). Numbers larger than the extended counter range can also be produced by cascading the PC74HC/HCT4059 with some other counting devices. Figure 13 shows such an arrangement where only one fixed divide-by number is desired. The dual flip-flop wired to produce a divide-by-3 count can be replaced by other counters such as the "190", "191", "192", "193", "4017", "4510" and "4516". 1998 Jul 08 To verify: 15 690 + 2 x 8 000 x 2 = 47 690. It is important that the second counting device has an output that is HIGH or LOW during only one of its counting states. 13 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 Each AND gate is 1/4 of PC74HC/HCT08. Each OR gate is 1/3 of PC74HC/HCT4075. Each NOR gate is 1/2 of PC74HC/HCT4002. Each inverter is 1/6 of PC74HC/HCT04. Fig.11 BCD switch compatible divide-by-n system suitable for divide-by-5 and divide-by-8 mode. Divides by any number from 3 to 256 000. 1998 Jul 08 14 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 Fig.12 Dividing-by any number from 99 003 to 114 999 (in this example n = 114 616). Fig.13 Division by 47 690 in divide-by-2 mode. (1) 1 RC -------------------------------------0.2 x f CP ( Hz ) (2) It is assumed that the fCP starts directly after the power-on. Any additional delay in starting fCP must be added to the RC time. Fig.14 External circuit for master preset at start-up. 1998 Jul 08 15 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 PACKAGE OUTLINES seating plane DIP24: plastic dual in-line package; 24 leads (300 mil) SOT222-1 ME D A2 L A A1 c e Z w M b1 (e 1) MH b 13 24 pin 1 index E 1 12 0 5 10 mm scale DIMENSIONS (millimetre dimensions are derived from the original inch dimensions) UNIT A max. A1 min. A2 max. b b1 c D (1) E (1) e e1 L ME MH w Z (1) max. mm 4.70 0.38 3.94 1.63 1.14 0.56 0.43 0.36 0.25 31.9 31.5 6.73 6.48 2.54 7.62 3.51 3.05 8.13 7.62 10.03 7.62 0.25 2.05 inches 0.185 0.015 0.155 0.064 0.045 0.022 0.017 0.014 0.010 1.256 1.240 0.265 0.255 0.100 0.300 0.138 0.120 0.32 0.30 0.395 0.300 0.01 0.081 Note 1. Plastic or metal protrusions of 0.01 inches maximum per side are not included. OUTLINE VERSION SOT222-1 1998 Jul 08 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION ISSUE DATE 95-03-11 MS-001AF 16 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 seating plane DIP24: plastic dual in-line package; 24 leads (600 mil) SOT101-1 ME D A2 L A A1 c e Z b1 w M (e 1) b MH 13 24 pin 1 index E 1 12 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 min. A2 max. b b1 c D (1) E (1) e e1 L ME MH w Z (1) max. mm 5.1 0.51 4.0 1.7 1.3 0.53 0.38 0.32 0.23 32.0 31.4 14.1 13.7 2.54 15.24 3.9 3.4 15.80 15.24 17.15 15.90 0.25 2.2 inches 0.20 0.020 0.16 0.066 0.051 0.021 0.015 0.013 0.009 1.26 1.24 0.56 0.54 0.10 0.60 0.15 0.13 0.62 0.60 0.68 0.63 0.01 0.087 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT101-1 051G02 MO-015AD 1998 Jul 08 EIAJ EUROPEAN PROJECTION ISSUE DATE 92-11-17 95-01-23 17 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 SO24: plastic small outline package; 24 leads; body width 7.5 mm SOT137-1 D E A X c HE y v M A Z 13 24 Q A2 A (A 3) A1 pin 1 index Lp L 1 12 e detail X w M bp 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y mm 2.65 0.30 0.10 2.45 2.25 0.25 0.49 0.36 0.32 0.23 15.6 15.2 7.6 7.4 1.27 10.65 10.00 1.4 1.1 0.4 1.1 1.0 0.25 0.25 0.1 0.9 0.4 inches 0.10 0.012 0.096 0.004 0.089 0.01 0.019 0.013 0.014 0.009 0.61 0.60 0.30 0.29 0.050 0.419 0.043 0.055 0.394 0.016 0.043 0.039 0.01 0.01 0.004 0.035 0.016 Z (1) 8o 0o Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT137-1 075E05 MS-013AD 1998 Jul 08 EIAJ EUROPEAN PROJECTION ISSUE DATE 95-01-24 97-05-22 18 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between 50 and 300 seconds depending on heating method. Typical reflow temperatures range from 215 to 250 C. SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45 C. WAVE SOLDERING This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "Data Handbook IC26; Integrated Circuit Packages" (order code 9398 652 90011). Wave soldering techniques can be used for all SO packages if the following conditions are observed: * A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used. DIP * The longitudinal axis of the package footprint must be parallel to the solder flow. SOLDERING BY DIPPING OR BY WAVE The maximum permissible temperature of the solder is 260 C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. * The package footprint must incorporate solder thieves at the downstream end. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. Maximum permissible solder temperature is 260 C, and maximum duration of package immersion in solder is 10 seconds, if cooled to less than 150 C within 6 seconds. Typical dwell time is 4 seconds at 250 C. REPAIRING SOLDERED JOINTS A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 C, contact may be up to 5 seconds. REPAIRING SOLDERED JOINTS Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 C. SO REFLOW SOLDERING Reflow soldering techniques are suitable for all SO packages. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. 1998 Jul 08 19 Philips Semiconductors Product specification Programmable divide-by-n counter 74HC/HCT4059 DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 1998 Jul 08 20