E M C C o m p o n e n t s July 2014 Common Mode Filters For power line ACM series ACM4520 ACM7060 ACM9070 ACM1211 ACM1513 [1808 inch]* [2824 inch] [3628 inch] [4844 inch] [6052 inch] * Dimensions Code JIS[EIA] (2/15) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-02 / 20140717 / e9713_acm.fm (3/15) E M C C o m p o n e n t s Common Mode Filters Product compatible with RoHS directive Halogen-free Compatible with lead-free solders For power line Overview of the ACM Series FEATURES Chip common mode filter for large current applications. For each series, there is excellent common mode impedance and noise suppression in a compact case. ACM4520 Low profile and small size makes it optimal for surface mounting. ACM7060, 9070, 1211, 1513 Compatible with high-density portable devices, which are always being made smaller and lighter, because the height has been reduced. APPLICATION ACM4520 Power line noise countermeasure for electronic equipment (DVCs, DVD cams, DSCs, etc.). ACM7060, 9070, 1211, 1513 Power line noise countermeasure for various electronic equipment. Noise countermeasure for adapter lines and battery lines or larger electronic equipment such as note book PCs and word processors. PART NUMBER CONSTRUCTION ACM Series name 4520 LxWxH Dimensions (mm) 4520 4.7x4.5x2.0 7060 7.0x6.0x3.5 9070 9.0x7.0x4.5 1211 12.0x11.0*6.0 1513 15.0x13.0x6.0 - 901 - Impedance (:) at 100MHz 901 900 142 1400 2P - T Number of lines 2P 2 lines - Packaging style T TL Internal code o180mm reel o330mm reel OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Type ACM4520 Temperature range Operating Storage temperature temperature C C -40 to +85 -40 to +85 ACM7060 -40 to +85 -40 to +85 ACM9070 -40 to +85 -40 to +85 ACM1211 -40 to +85 -40 to +85 ACM1513 -40 to +85 -40 to +85 The Storage temperature range is for after the circuit board is mounted. Reel diameter Package quantity Individual weight mm o180 o330 o330 o330 o330 o330 pieces/reel 800 2,500 1,500 800 500 500 g 0.15 0.35 0.82 2.2 3.15 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. * All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm.fm (4/15) E M C C o m p o n e n t s Overview of the ACM Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 10 to 30s Peak Temp. T4 245C Time t3 5s * All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm.fm (5/15) E M C C o m p o n e n t s ACM series ACM4520 Type SHAPE & DIMENSIONS 4.70.2 4.5 4 2 3 4.50.2 1 0.65 0.65 2.0max. Ferrite Wire 0.75 0.75 2.0 Dimensions in mm RECOMMENDED LAND PATTERN 3.5 1.25 2.0 0.95 1.05 0.95 1.25 CIRCUIT DIAGRAM 1 4 2 3 * No polarity Dimensions in mm * All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm.fm (6/15) E M C C o m p o n e n t s ACM series ACM4520 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance (: ) [at 100MHz] min. typ. 180 230 300 420 650 900 1000 1400 DC resistance (: )max. [1 line] 0.05 0.055 0.06 0.08 Rated current (A)max. 60C 3.0 2.8 2.3 1.7 85C 2.6 2.4 2.0 1.5 Rated voltage (V)max. Insulation resistance (M: )min. Part No. 50 50 50 50 10 10 10 10 ACM4520-231-2P-- ACM4520-421-2P-- ACM4520-901-2P-- ACM4520-142-2P-- : Includes packaging style indication (T: o180mm reel, TL: o330mm reel). Measurement equipment Measurement item Product No. Common mode impedance 4991A DC resistance 4338A Insulation resistance 4339A Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 142 Common mode 1000 Impedance () 901 Common mode 421 Common mode 421 Differential mode 100 231 Differential mode 901 Differential mode 231 Common mode 10 1 142 Differential mode 1 10 100 1000 Frequency (MHz) Measurement equipment Product No. Manufacturer 4991A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm.fm (7/15) E M C C o m p o n e n t s ACM series ACM7060 Type SHAPE & DIMENSIONS 7.00.2 4 2 3 6.00.2 1 4.0typ. 1.50.2 3.5max. 1.50.2 1.50.2 1.50.2 1.50.2 Dimensions in mm 1.5 2 3 1 4 1.5 2.5 4.0 2.5 CIRCUIT DIAGRAM 1.5 RECOMMENDED LAND PATTERN * No polarity Dimensions in mm * All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm.fm (8/15) E M C C o m p o n e n t s ACM series ACM7060 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance (: ) [100MHz] min. typ. 225 300 500 700 DC resistance (m: )max. [1 line] 10 15 Rated current (A)max. 5 4 Measurement equipment Measurement item Product No. Common mode impedance 4991A DC resistance 4338A Insulation resistance 4339A Equivalent measurement equipment may be used. Insulation resistance (M: )min. 10 10 Rated voltage (V)max. Part No. 80 80 ACM7060-301-2PL-TL01 ACM7060-701-2PL-TL01 Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 701 Differential mode Impedance () 1000 301 Common mode 701 Common mode 100 301 Differential mode 10 1 1 10 100 1000 Frequency (MHz) Measurement equipment Product No. Manufacturer 4991A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm.fm (9/15) E M C C o m p o n e n t s ACM series ACM9070 Type SHAPE & DIMENSIONS 9.00.2 4 2 3 7.00.2 1 6.0typ. 1.50.2 4.5max. 1.50.2 1.50.2 1.50.2 2.00.2 Dimensions in mm CIRCUIT DIAGRAM 2 3 1 4 1.5 2.0 1.5 RECOMMENDED LAND PATTERN 2.5 6.0 2.5 * No polarity Dimensions in mm * All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm.fm (10/15) E M C C o m p o n e n t s ACM series ACM9070 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance (: ) [100MHz] min. typ. 500 700 DC resistance (m: )max. [1 line] 10 Rated current (A)max. 5 Measurement equipment Measurement item Product No. Common mode impedance 4991A DC resistance 4338A Insulation resistance 4339A Equivalent measurement equipment may be used. Insulation resistance (M: )min. 10 Rated voltage (V)max. Part No. 80 ACM9070-701-2PL-TL01 Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 Impedance () 1000 701 Common mode 701 Differential mode 100 10 1 1 10 100 1000 Frequency (MHz) Measurement equipment Product No. Manufacturer 4991A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm.fm (11/15) E M C C o m p o n e n t s ACM series ACM1211 Type SHAPE & DIMENSIONS 12.00.3 4 2 3 11.00.3 1 7.4typ. 2.30.2 6.0max. 2.30.2 2.70.2 2.70.2 Dimensions in mm 2.50.2 2.7 2 3 1 4 2.7 3.2 7.6 3.2 CIRCUIT DIAGRAM 2.5 RECOMMENDED LAND PATTERN * No polarity Dimensions in mm * All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm.fm (12/15) E M C C o m p o n e n t s ACM series ACM1211 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance (: ) [100MHz] min. typ. 500 700 750 1000 DC resistance (m: )max. [1 line] 6 14 Rated current (A)max. 8 6 Measurement equipment Measurement item Product No. Common mode impedance 4991A DC resistance 4338A Insulation resistance 4339A Equivalent measurement equipment may be used. Insulation resistance (M: )min. 10 10 Rated voltage (V)max. Part No. 80 80 ACM1211-701-2PL-TL01 ACM1211-102-2PL-TL01 Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 102 Differential mode Impedance () 701 Differential mode 102 Common mode 1000 701 Common mode 100 10 1 1 10 100 1000 Frequency (MHz) Measurement equipment Product No. Manufacturer 4991A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm.fm (13/15) E M C C o m p o n e n t s ACM series ACM1513 Type SHAPE & DIMENSIONS 13.00.4 15.00.5 1 4 2 3 10.4typ. 2.30.2 6.0max. 2.30.2 2.70.2 3.80.2 2.70.2 Dimensions in mm CIRCUIT DIAGRAM 2 3 1 4 2.7 3.8 2.7 RECOMMENDED LAND PATTERN * No polarity 3.3 10.4 3.3 Dimensions in mm * All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm.fm (14/15) E M C C o m p o n e n t s ACM series ACM1513 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance (: ) [100MHz] min. typ. 450 550 DC resistance (m: )max. [1 line] 4 Rated current (A)max. 10 Measurement equipment Measurement item Product No. Common mode impedance 4991A DC resistance 4338A Insulation resistance 4339A Equivalent measurement equipment may be used. Insulation resistance (M: )min. 10 Rated voltage (V)max. Part No. 50 ACM1513-551-2PL-TLHF Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 Impedance () 701 Common mode 1000 701 Differential mode 100 10 1 10 100 1000 Frequency (MHz) Measurement equipment Product No. Manufacturer 4991A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm.fm (15/15) E M C C o m p o n e n t s ACM series Packaging style REEL DIMENSIONS 2.00.5 E Type ACM4520 N ACM7060 ACM9070 ACM1211 ACM1513 A o3302 o1803 o3302 o3302 o3302 o3302 W1 13.50.5 130.3 16.4+2/-0 16.4+2/-0 24.4+2/-0 24.4+2/-0 W2 17.51 171.4 20.4 typ. 20.4 typ. 28.4 typ. 28.4 typ. N 1001 60+1/-0 1001 1001 1001 1001 E 2 typ. 2 typ. 2 typ. 2 typ. 2 typ. 2 typ. 1.0 o13.00.2 W1 o21.00.8 W2 A Dimensions in mm TAPE DIMENSIONS t P0 B W F P2 E oD0 K P1 A Dimensions in mm Type ACM4520 ACM7060 ACM9070 ACM1211 ACM1513 A 4.750.1 6.60.1 7.60.1 11.50.1 13.40.1 B 5.050.1 7.60.1 9.60.1 12.50.1 15.50.1 oD0 1.55+0.1/0 1.5+0.1/0 1.5+0.1/0 1.5+0.1/0 1.5+0.1/0 E 1.750.1 1.750.1 1.750.1 1.750.1 1.750.1 F 5.50.05 7.50.1 7.50.1 11.50.1 11.50.1 P0 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 P1 8.00.1 8.00.1 12.00.1 16.00.1 16.00.1 P2 2.00.05 2.00.1 2.00.1 2.00.1 2.00.1 W K 12.00.2 2.050.05 16.00.3 3.60.1 16.00.3 4.60.1 24.00.3 6.40.1 24.0+0.3/-0.1 7.30.1 t 0.30.1 0.40.05 0.40.05 0.50.05 0.40.05 500 to 560min. 160min. Taping 440min. Drawing direction Dimensions in mm * All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm.fm Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: TDK: ACM1513-551-2PL ACM1211-102-2PL-TL01 ACM1211-701-2PL-TL01 ACM7060-701-2PL-TL01 ACM7060-3012PL-TL01 ACM7060-301-2PL-TL ACM1513-551-2PL-T ACM9070-701-2PL-TL01 ACM4520-142-2P-T000 ACM4520901-2P-T000 ACM1513-551-2PL-TL ACM9070-701-2PL-T01 ACM4520-231-2P-T000 ACM4520-421-2P-T000 ACM4520V-901-2P-T00 ACM4520V-231-2P-T00 ACM4520V-421-2P-T00 ACM4520V-142-2P-T00 ACM1513-5512PL-TLHF