DATA SHEET DATA SHEET MOS INTEGRATED CIRCUIT PD6121, 6122 REMOTE CONTROL TRANSMISSION CMOS IC The PD6121, 6122 are infrared remote control transmission ICs using the NEC transmission format that are ideally suited for TVs, VCRs, audio equipment, air conditioners, etc. By combining external diodes and resistors, a maximum * of 65,536 custom codes can be specified. These ICs come in small packages, thus facilitating the design of light and compact remote control transmitters. The NEC transmission format consists of leader codes, custom codes (16 bits), and data codes (16 bits). It can be used for various systems through decoding by a microcontroller. FEATURES * * * * Low-voltage operation: VDD = 2.0 to 3.3 V Low current dissipation: 1 A Max. (at standby) Custom codes: 65,536 (set by external diodes and resistors) * Data codes: * PD6121: 32 codes (single input), 3 codes (double input), expandable up to 64 codes through SEL pin * PD6122: 64 codes (single input), 3 codes (double input), expandable up to 128 codes through SEL pin * PD6121, 6122 are transmission code-compatible (NEC transmission format) with the PD1913CNote, 1943GNote, 6102GNote, and 6120CNote. * Pin compatibility: * PD6121G-001 is pin-compatible with the PD1943G (However, capacitance of capacitor connected to oscillator pin and other parameters vary) * PD6122G-001 is pin-compatible with the PD6102G (However, capacitance of capacitor connected to oscillator pin and other parameters vary) * Standard products (Ver. I, Ver. II specifications) * Note Provided for maintenance purpose only * When using this product (in NEC transmission format), please order custom codes from NEC. * New custom codes for the PD6121G-002, PD6122G-002 cannot be ordered. The information in this document is subject to change without notice. Document No. U10114EJ6V0DS00 (6th edition) (Previous No. IC-1813) Date Published October 1995 P) Printed in Japan The mark * shows revised points. (c) 1994 1994 PD6121, 6122 * ORDERING INFORMATION Part number Package Description PD6121G-001 20-pin plastic SOP (375 mil) Standard (Ver I spec.) PD6121G-002 20-pin plastic SOP (375 mil) Standard (Ver II spec.) PD6122G-001 24-pin plastic SOP (375 mil) Standard (Ver I spec.) PD6122G-002 24-pin plastic SOP (375 mil) Standard (Ver II spec.) PIN CONFIGURATION (Top View) PD6121 20 19 18 17 16 15 14 13 12 11 CCS KI/O0 KI/O1 KI/O2 KI/O3 KI/O4 KI/O5 KI/O6 KI/O7 LMP KI2 KI3 KI4 KI5 KI6 KI7 REM VDD SEL OSCO OSCI VSS 1 2 3 4 5 6 7 8 9 10 11 12 PD6122G-001 PD6122G-002 PD6121G-001 PD6121G-002 1 2 3 4 5 6 7 8 9 10 KI0 KI1 KI2 KI3 REM VDD SEL OSCO OSCI VSS PD6122 PIN IDENTIFICATIONS CCS : Custom code selection input REM : KI 0 - KI 7 : Key input SEL : SEL input KI/O 0 - KI/O 7 : Key input/output V DD : Power supply pin LMP Lamp output V SS : GND pin : OSCI, OSCO: 2 Remote output Resonator connection pin 24 23 22 21 20 19 18 17 16 15 14 13 KI1 KI0 CCS KI/O0 KI/O1 KI/O2 KI/O3 KI/O4 KI/O5 KI/O6 KI/O7 LMP PD6121, 6122 BLOCK DIAGRAM * OSCO OSCI VDD LMP REM Output circuit Oscillator Controller Frequency divider SEL Data register Timing generator VSS CCS KI0 - KInNote Note Key input/output circuit Key input circuit KI/O0 KI/O2 KI/O1 KI/O3 KI/O4 KI/O5 KI/O6 KI/O7 PD6121: KI0 - KI3 PD6122: KI0 - KI7 DIFFERENCES BETWEEN PRODUCTS Part number Item PD6121 Operating voltage PD6122 VDD = 2.0 to 3.3 V 1 A MAX. Current consumption (at standby) Custom codes Data codes No. of KI pins 65,536 (16-bit setting) 32 x 2 64 x 2 4 8 No. of KI/O pins 8 SEL pin Transmission format Package Provided NEC transmission format 20-pin plastic SOP (375 mil) 24-pin plastic SOP (375 mil) 3 PD6121, 6122 1. PIN FUNCTIONS (1) Key input pins (KI0 to KI7), key input/output pins (KI/O0 to KI/O7) A pull-down resistor is placed between key input pins and a VSS pin. When several keys are pressed simultaneously, the transmission of the corresponding signals is inhibited by a multiple-input prevention circuit. In the case of double-key input, transmission is inhibited if both keys are pressed simultaneously (within 36 ms interval); if not pressed simultaneously, the priority of transmission is first key, then second key. When a key is pressed, the custom code and data code reading is initiated, and 36 ms later, output to REM output is initiated. Thus if the key is pressed during the initial 36 ms, one transmission is performed. If a key is kept pressed for 108 ms or longer, only leader codes are consecutively transmitted until the key is released. Keys can be operated intermittently at intervals as short as 126 ms (interval between two on's), making this an extremely fast-response system. (2) Resonator connection pins (OSCI, OSCO) The oscillator starts operating when it receives a key input. Use a ceramic resonator with a frequency between 400 and 500 kHz. (3) Power-supply pin The power supply voltage is supplied by two 3-V batteries. A broad range of operating power supply voltage is allowed, from 2.0 to 3.3 V. The supply current falls below 1 A when the oscillator is inactive when no keys are pressed. (4) REM output pin The REM output pin outputs the transmission code, which consists of the leader code, custom code (16 bits), and data code (16 bits) (Refer to 2. NEC TRANSMISSION FORMAT (REM OUTPUT)). (5) SEL input pin By controlling D7 of the data code with this pin, the PD6121 and PD6122 can transmit 64 and 128 different data codes, respectively. By connecting the SEL pin to VDD or VSS, D7 is set to "0" or "1", respectively. This pin has high-impedance input, therefore be sure to connect it either to VDD or VSS. (6) CCS input pin By placing a diode between the CCS pin and the KI/O pin, it is possible to set a custom code. When a diode is connected, the corresponding custom code is "1", and when not connected, it is "0". (7) LMP output pin The LMP pin outputs a low-level signal while the REM pin outputs a transmission code. 4 PD6121, 6122 2. NEC TRANSMISSION FORMAT (REM OUTPUT) The NEC transmission format consists of the transmission of a leader code, 16-bit custom codes (Custom Code, Custom Code'), and 16-bit data codes (Data Code, Data Code) at one time, as shown in Figure 2-1. Also refer to 4. REMOTE OUTPUT WAVEFORM. Data Code is the inverted code of Data Code. The leader code consists of a 9-ms carrier waveform and a 4.5-ms OFF waveform and is used as leader for the ensuing code to facilitate reception detection. Codes use the PPM (Pulse Position Modulation) method, and the signals "1" and "0" are fixed by the interval between pulses. Figure 2-1. REM Output Code = = = = = = = = C0 C1 C2 C3 C4 C5 C6 C7 C0' C1' C2' C3' C4' C5' C6' C7' D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 C0 C1 C2 C3 C4 C5 C6 C7 or or or or or or or or C0 C1 C 2 C 3 C 4 C 5 C 6 C 7 Leader Code Custom Code Custom Code' Data Code Data Code Cautions 1. Use any of the possible 256 kinds of custom codes specified with 00xxH (diode not connected), as desired. If intending to use custom codes other than 00xxH, please consult NEC in order to avoid various types of errors from occurring between systems. 2. When receiving data in the NEC transmission format, check that the 32 bits made up of the 16-bit custom code (Custom Code, Custom Code') and the 16-bit data code (Data Code, Data Code) are fully decoded, and that there are no signals with the 33rd bit and after (be sure to check also Data Code). 5 PD6121, 6122 * 3. CUSTOM CODE (CUSTOM CODE, CUSTOM CODE') SETTING The custom code is set in two different ways depending on whether Ver I or Ver II specifications are employed. Figure 3-1. Custom Code Setting Higher 8 bits of custom code Lower 8 bits of custom code' Ver I Fixed by external diode bit Fixed by external pull-up resistor bit Ver II C0, C1, C2 ... Fixed by connecting CCS pin and either one of pins KI/O0 to KI/O7 C3 to C7 ... Fixed by absence or presence of external pull-up resistor for KI/O6, KI/O7 Fixed by external pull-up resistor (KI/O0 to KI/O5) bit Remark The PD6121-001 has Ver I specifications and is pin-compatible with the PD1943G, and the PD6122001 has Ver I specifications and is pin-compatible with the PD6102G. If used as pin-compatible products, please note the following points. 1 Connect the SEL pin to V DD. 2 Change the capacitance of the capacitor connected to the resonator connection pin (Refer to 9. ELECTRICAL SPECIFICATIONS). A custom code setting example is shown below. * 3.1 Standard versions with Ver I specs. (PD6121-001, PD6122-001) Each of the higher 8 bits of the custom code is set to "1" when a diode is connected between the CCS pin and the corresponding KI/O pin, and is set to "0" when no diode is connected. If a pull-up resistor is connected to the KI/O pin corresponding to one of the lower 8 bits of the custom code', the bit is first set to "1". Based on the 1's information of the lower 8 bits of the custom code', the corresponding bit of the higher 8 bits of the custom code is then captured and not inverted. The non-inverted value is finally overwritten to the corresponding bit of the lower 8 bits of the custom code'. The inverse occurs when no pull-up resistor is connected. It follows from the above that the custom code can be set in 65,536 different ways depending on whether or not a diode and/or pull-up resistor are present. Please refer to Figure 3-2 Example of Custom Code Setting for Ver I Specifications (PD6121-001, 6122001). Figure 3-2. Example of Custom Code Setting for Ver I Specifications (PD6121-001, 6122-001) Configuration example CCS KI/O0 VDD 6 KI/O1 KI/O2 KI/O3 VDD KI/O4 KI/O5 KI/O6 KI/O7 PD6121, 6122 The higher 8 bits of the custom code are determined by the diode connected to the CCS pin and KI/O pin. Set custom code Higher 8 bits of custom code 1 0 0 0 1 0 1 0 C 0 C 1 C 2 C3 C4 C 5 C 6 C7 Set to "1" by diode The inversion/non-inversion of the lower 8 bits of the custom code' is determined by the pull-up resistor connected to the KI/O pin. Set custom code Lower 8 bits of custom code' 1 0 0 0 1 0 0 0 C0' C1' C2' C3' C4' C5' C6' C7' Set to "1" by pull-up resistor, that is, bit for non-inversion of custom code is set 1: Non-inversion for C0 to C7 0: Inversion for C0 to C7 When the above-described setting is done, the following custom code is output. Custom code Higher 8 bits of custom code 1 0 0 0 1 0 1 0 C0 C1 C2 C3 C4 C5 C6 C7 Lower 8 bits of custom code' 1 1 1 1 1 1 0 1 C0' C1' C2' C3' C4' C5' C6' C7' C0 C1 C2 C3 C4 C5 C6 C7 Remark Codes are transmitted from the LSB. 7 PD6121, 6122 * 3.2 Standard versions with Ver II specs. (PD6121-002, 6122-002) In Ver II, the CCS pin does not have the external diode reading function. The allocation of C 2, C 1 and C 0 of the higher 8 bits of the custom code is done by connecting the CCS pin to any one of the KI/O 0 to KI/O 7 pins, as shown below. Pin connected to CCS pin C2 C 1 C 0 KI/O0 0 0 0 KI/O1 0 0 1 KI/O2 0 1 0 KI/O3 0 1 1 KI/O4 1 0 0 KI/O5 1 0 1 KI/O6 1 1 0 KI/O7 1 1 1 When CCS pin is open, (C2 C1 C0) = (0 0 0) * The allocation of C 7, C 6, C5, C 4 and C 3 of the higher 8 bits of the custom code is as follows depending on whether a pull-up resistor is provided. Pull-up Resistor Caution C 7 to C3 of Higher 8 bits of Custom Code KI/O 6 KI/O 7 C7 C6 C5 C4 C3 Not Provided Not Provided 0 0 0 0 0 Not Provided Provided 1 0 0 1 1 Provided Not Provided 1 0 0 0 0 Provided Provided 1 1 1 0 1 In Ver II, it is not possible to set all custom codes. Also, new custom codes cannot be ordered for Ver II products; therefore, Ver I products should be used if new custom codes are required. 8 PD6121, 6122 Figure 3-3. Example of Custom Code Setting for Ver II Specifications ( PD6121-002, 6122-002) Configuration Example CCS KI/O1 KI/O0 VDD KI/O2 KI/O3 KI/O4 KI/O5 KI/O6 KI/O7 VDD VDD VDD ROM3 selector : Connected Connection of any one line : Not connected C 2, C 1 and C 0 of the higher 8 bits of the custom code are fixed by connecting the CCS pin to KI/O 0 to KI/ O 7. Therefore, in the configuration example, they become 1 0 0 . C0 C 1 C 2 C 7, C 6, C 5, C 4 and C 3 of the higher 8 bits of the custom code are selected and fixed by the pull-up resistor connected to KI/O 6 and KI/O 7 in four channels. Pull-up resistor C7 C6 C5 C4 C3 KI/O6 KI/O7 1 0 1 1 0 Disconnected Disconnected 0 0 1 1 1 Disconnected Connected 1 1 0 1 1 Connected Disconnected 1 1 1 1 1 Connected Connected * In this configuration example, C 3 to C 7 of the higher 8 bits of the custom code become 1 1 0 1 1 . C3 C 4 C 5 C 6 C 7 The inversion/non-inversion of the lower 8 bits of the custom code' is fixed by the bit of the external pullup resistor of KI/O 0 to KI/O 5. External setting (Refer to Configuration Example) Lower 8 bits of custom code' 1 0 1 0 0 0 0 0 C0' C1' C2' C3' C4' C5' C6' C7' Pull-up resistor bit (KI/O0, KI/O2) Bit for non-inversion of custom code is set 1: Non-inversion for C0 to C7 0: Inversion for C0 to C7 Caution C6' and C7' are fixed to 0. 9 * PD6121, 6122 As noted above, setting the pull-up resistor and connection, produces the following custom code. Custom code Higher 8 bits of custom code * 1 0 0 1 1 0 1 1 C0 C1 C2 C3 C4 C5 C6 C7 Lower 8 bits of custom code' 1 1 0 0 0 1 0 0 C0' C1' C2' C3' C4' C5' C6' C7' C0 C1 C2 C3 C4 C5 C6 C7 Remark Codes are transmitted from the LSB. 10 PD6121, 6122 4. REMOTE OUTPUT WAVEFORM (NEC TRANSMISSION FORMAT: ONE-SHOT COMMAND TRANSMISSION MODE) * When fOSC = 455 kHz (1) Remote (REM) output (from stage 2 , transmission occurs only when key is kept depressed) REM output 58.5 to 76.5 ms 108 ms 108 ms 1 2 (2) Magnification of stage 1 3 REM output 9 ms 4.5 ms Custom Code 8 bits 13.5 ms Leader Code Custom Code' 8 bits Data Code 8 bits 18 ms to 36 ms Data Code 8 bits Stop Bit 1 bit 27 ms 58.5 ms to 76.5 ms (3) Magnification of waveform 3 REM output 9 ms 4.5 ms 0.56 ms 1.125 ms 2.25 ms 13.5 ms 0 1 1 0 0 (4) Magnification of waveform 2 REM output 9 ms 2.25 ms 11.25 ms 0.56 ms Stop Bit Leader Code (5) Carrier waveform (Magnification of HIGH period of codes) REM output 8.77 s 26.3 s 9 ms or 0.56 ms Carrier frequency: fc = fosc/12 = 38 kHz Remark If a key is kept depressed, the second and subsequent times, only the leader code and the stop bit are transmitted, which allows power savings for the infrared-emitting diode. If a command is issued continuously in the same way the second and subsequent times as the first time, refer to 7. ONE-SHOT/CONTINUOUS COMMAND TRANSMISSION MODE. 11 PD6121, 6122 KEY DATA CODES (SINGLE INPUT) Note 12 KI/O0 * * * * KI/O1 * * * * KI/O2 * * * * KI/O3 * * * * KI/O4 * * * * KI/O5 * * * * KI/O6 * * * * KI/O7 * KI4 * * CONNECTION KI5 KI6 KI7 * KI/O KI/O0 * * * * KI/O1 * * * * KI/O2 * * * * KI/O3 * * * * KI/O4 * * * * KI/O5 * * * * KI/O6 * * * * KI/O7 * * D0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 D1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 D2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 D0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 D1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 D2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 DATA CODE D3 D4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 DATA CODE D3 D4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 D5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D7Note 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 D5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 D7 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 NOTES PD1913C PD6120C Unavailable PD1913C PD6120C Unavailable Unavailable PD1913C PD6120C * PD6121 * PD6122 * PD6122 only NOTES PD1943G PD1913C PD6120C PD6121G PD1943G PD1913C PD6120C PD6121G PD1943G PD1913C PD6120C PD6121G PD1943G PD1913C PD6120C PD6121G PD1943G PD1913C PD6120C PD6121G PD1943G PD1913C PD6120C PD6121G PD1943G PD1913C PD6120C PD6121G PD1943G PD1913C PD6120C PD6121G K33 K34 K35 K36 K37 K38 K39 K40 K41 K42 K43 K44 K45 K46 K47 K48 K49 K50 K51 K52 K53 K54 K55 K56 K57 K58 K59 K60 K61 K62 K63 K64 * KI/O KEY CONNECTION KI1 KI2 KI3 K1 K2 K3 K4 K5 K6 K7 K8 K9 K10 K11 K12 K13 K14 K15 K16 K17 K18 K19 K20 K21 K22 K23 K24 K25 K26 K27 K28 K29 K30 K31 K32 KI0 * KEY 5. * Unavailable Unavailable Unavailable Unavailable Unavailable Unavailable Unavailable Unavailable Bit D7 is "0" when the SEL pin is connected to VDD, and "1" when it is connected to VSS. PD6121, 6122 6. DOUBLE-INPUT OPERATION All keys are provided with a multiple-input prevention circuit. When two or more keys are pressed simulta- neously, no signal is transmitted; but when the keys K21 and K22, K21 and K23, or K21 and K24 are pressed together, D 5 is set to "1". However, the way keys are pressed determines the priority: If K22/K23/K24 are pressed 126 ms or longer after K21 is pressed, transmission is performed in this mode. Double-input key operation is ideally suited for tape recording error prevention applications. Double-Input Operation Key Codes KEY D0 D1 D2 D3 D4 D5 D6 D7 K21 + K22 1 0 1 0 1 1 0 0/1 K21 + K23 0 1 1 0 1 1 0 0/1 K21 + K24 1 1 1 0 1 1 0 0/1 Double-Input Operation Timing 1 Double-input transmission K21 code transmission K21 D5 + K22/K23/K24 code transmission t > 126 ms push K22/K23/K24 push 2 No operation K21 code transmission K21 Transmission stop 36 ms < t < 126 ms push K22/K23/K24 push 3 No operation No transmission K21 -36 ms < t < 36 ms push K22/K23/K24 push 4 No operation K21 t > 126 ms K22/K23/K24 K22/K23/K24 code transmission push Transmission stop push 13 PD6121, 6122 7. ONE-SHOT/CONTINUOUS COMMAND TRANSMISSION MODE 7.1 One-shot Command Transmission Mode In order to reduce the average transmission current, the PD6120C, 6121G, and 6122G transmit data only once, and thereafter transmit just the leader code and stop bit indicating that a key is depressed. As a result, this transmission method (one-shot command transmission mode) has the following characteristics. Advantages * Average transmission current is reduced to 1/3 to 1/4 compared with continuous command transmission mode * Reduced software load for reception program (not all commands are processed all the time) * This mode distinguishes when a key is pressed several times successively and when a key is kept depressed. Disadvantages * If a command is not read the first time, it cannot be read a second time * If a signal transmission is interrupted while continuous commands are executed, subsequent commands cannot be executed. Moreover, when f OSC = 455 kHz, the average current to the infrared-emitting diode is roughly equivalent to 3 % of the peak current. I AVE = (9 ms + 0.56 ms)/108 ms x 1/3 (duty) = 2.95 % (first command is ignored) 7.2 Continuous Command Transmission Mode A continuous command transmission mode for transmitting data a second or more times is also available. As shown in Figure 7-2, it is possible to continuously transmit commands for all the keys or for individual key output lines simply by adding a diode D and connecting it to KI 0 or KI/O. In this case, the average transmission current is larger than that in the one-shot command transmission mode. When f OSC = 455 kHz, the average current to the infrared-emitting diode is roughly equivalent to 9 % of the peak current. I AVE = (9 ms + 0.56 ms x 33)/108 ms x 1/3 (duty) = 8.48 % Cautions 1. If the double input key (K21-K24) is used in the continuous command transmission mode, double-input key transmission is not performed (D5 does not become 1). 2. When the voltage drop of the REM output is large, the signal is not transmitted accurately. Therefore, keep the REM output current within 1 mA. Figure 7-1 shows the continuous command transmission mode. 14 PD6121, 6122 Figure 7-1. Continuous Command Transmission Mode (When fOSC = 455 kHz) (1) PD6120C, 6121G, 6122G REM output 58.5 to 76.5 ms 31.5 to 49.5 ms Average transmission current ratio ITYP = 8.48 % x Ipeak (LED) 108 ms LMP output (2) PD1913C, 1943G, 6102G 1 K1 to K20, K33 to K52 (KO0 to KO4) REM output 67.5 ms 38 ms 105.5 msNote Average transmission current ratio ITYP = 8.68 % x Ipeak (LED) LMP output 2 K21 to K32, K53 to K64 (KO5 to KO7) REM output 67.5 ms 20 ms 87.5 msNote Average transmission current ratio ITYP = 10.47 % x Ipeak (LED) LMP output Note In the case of the PD1913C, 1943G and 6102G, the transmission repeat cycle (T) varies depending on the key. Remark ITYP = IAVE x Ipeak (LED) IAVE = (9 ms + 0.56 ms x 33)/T ms x 1/3 (duty) 15 PD6121, 6122 Figure 7-2. Application Circuit for Continuous Command Transmission Mode 1 Continuous command transmission for all keysNote 1 REM output is input to KI0 with diode D. Ceramic resonator 455 kHz Transmission 47 F display 100 220 pF 220 pF OSCO OSCI + 82 LMP VDD REM 2.2 k PD6121G-001 PD6121G-002 VSS CCS KI2 KI0 KI3 KI1 KI/O0 KI/O1 KI/O2 KI/O3 KI/O4 KI/O5 KI/O6 KI/O7 VDD VDD 12 k Custom code selection resistor Diode D Key matrix Custom code selection diode 2 Continuous command transmission for key output lines REM output is input to KI/O with diode D. Ceramic resonator 455 kHz 100 220 pF 220 pF OSCO OSCI VDD Transmission 47 F display + 82 LMP REM 2.2 k PD6121G-001 PD6121G-002 VSS CCS KI2 KI0 KI3 KI1 KI/O0 KI/O1 KI/O2 KI/O3 KI/O4 KI/O5 KI/O6 KI/O7 VDD VDD Custom code selection diode 12 k Custom code selection resistor Diode D Continuous command transmission can be performed for keys whose KI/O output lines have received diode D input Note 2. Notes 1. * 2. Double-key transmission cannot be performed. If the KI/O5 output line (double-input key) is in the continuous command transmission mode, double-input key transmission is not performed (D5 does not become 1). Caution When the voltage drop of the REM output is large, the signal is not transmitted accurately. Therefore, keep the REM output current within 1 mA. 16 PD6121, 6122 8. APPLICATION CIRCUIT EXAMPLE (1) Example application circuit using PD6121 + Ceramic resonator 455 kHz OSCO 3V OSCI VDD SEL LMP REM Infrared-emitting diode SE303A-C SE307-C SE313 SE1003-C 2SC2001, 3616 2SD1513, 1616 2SD1614 PD6121G-001 VSS CCS KI0 KI3 KI/O0 KI/O7 VDD VDD Custom code selection resistor Key matrix 8 x 4 = 32 keys = Custom code selection diode (2) Example application circuit using PD6122 + Ceramic resonator 455 kHz OSCO SEL 3V OSCI VDD LMP REM Infrared-emitting diode SE303A-C SE307-C SE313 SE1003-C 2SC2001, 3616 2SD1513, 1616 2SD1614 PD6122G-001 VSS CCS KI0 KI7 KI/O0 KI/O7 VDD VDD Custom code selection resistor Key matrix 8 x 8 = 64 keys Custom code selection diode 17 PD6121, 6122 * (3) Application circuit example, receive side Microcomputer Key input Preamplifier (amplification, waveform shaping) Display IN OUT INT Control PIN photo diode PH302C PH310 PH320 Shield case Note 18 Communications PC2800A, 2801ANote PC2803 PC2804 The PC2801A's active level is high. 17K series 75X series 75XL series 78K series PD6121, 6122 9. ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings (T A = 25 C) Parameter Symbol Ratings Unit -0.3 to +6.0 V Supply voltage VDD Input voltage VI -0.3 to VDD + 0.3 V Power dissipation PD 250 mW Operating ambient temperature TA -20 to +75 C Storage temperature Tstg -40 to +125 C Recommended Operating Conditions (T A = -20 to +75 C) Parameter Symbol MIN. TYP. MAX. Unit Supply voltage VDD 2.0 3.0 3.3 V Oscillation frequency fOSC 400 455 500 kHz Input voltage VI VDD V Custom code select pull-up resistor RUP 200 240 k 0 160 DC Characteristics (T A = 25 C, V DD = 3.0 V) Parameter Symbol Condition MIN. TYP. MAX. Unit 0.1 1 mA 1 A Supply current 1 IDD1 fOSC = 455 kHz Supply current 2 IDD2 fOSC = STOP REM output current High IOH1 VO = 1.5 V -5 -8 mA REM output current Low IOL1 VO = 0.3 V 15 30 A LMP output current High IOH2 VO = 2.7 V -15 -30 A LMP output current Low IOL2 VO = 0.3 V 1 1.5 mA KI input current High IIH1 VI = 3.0 V 10 KI input current Low IIL1 VI = 0 V KI, SEL input voltage High VIH1 KI, SEL input voltage Low 30 A -0.2 A 2.1 3.0 V VIL1 0 0.9 V KI/O input voltage High VIH2 1.3 KI/O input voltage Low VIL2 KI/O input current High IIH2 VI = 3.0 V KI/O input current Low IIL2 VI = 0 V KI/O output current High IOH3 VO = 2.5 V KI/O output current Low IOL3 VO = 1.7 V CCS input voltage High VIH3 CCS input current High IIH3 Pull-up, VI = 3.0 V CCS input current Low IIL3 Pull-up, VI = 0 V CCS input current High IIH4 Pull-down, VI = 3.0 V CCS input current Low IIL4 Pull-down, VI = 0 V V 0.4 V 7 A -0.2 A -1.0 -2.5 mA 35 100 A 2 1.1 V 0.2 A -3 -8 A 10 30 A -0.2 A 19 PD6121, 6122 Recommended Ceramic Resonators (T A = -20 to +75 C, V DD = 2.0 to 3.3 V) * PD6121, 6122 Maker Product Recommended constant [pF] Operating voltage [V] C1 C2 MIN. MAX. CSB455E 220 220 2.0 3.3 CSB480E 220 220 2.0 3.3 Toko Corp. CRK455 120 300 2.0 3.3 Kyocera Corp. KBR-455BTLR 220 220 2.0 3.3 Murata Seisakusho Corp. Example of external circuit OSCI OSCO C1 C2 VDD Caution If using an oscillation circuit, wire the area enclosed in the dotted line in the figure in the manner indicated below in order to avoid negative effects such as from stray capacitance of wires. * Keep wiring as short as possible. * Do not cross other signal lines. Do not design wiring close to lines with large fluctuating current. * Make sure that the connection point of the oscillation circuit's capacitor has the same potential as VDD. * Do not extract signals from the oscillation circuit. 20 PD6121, 6122 10. PACKAGE DRAWINGS * (1) Package for the PD6121 20 PIN PLASTIC SOP (375 mil) 20 11 P detail of lead end 1 10 A H J K F G I E B L C N D M M NOTE Each lead centerline is located within 0.12 mm (0.005 inch) of its true position (T.P.) at maximum material condition. ITEM MILLIMETERS INCHES A 13.00 MAX. 0.512 MAX. B 0.78 MAX. 0.031 MAX. C 1.27 (T.P.) 0.050 (T.P.) D 0.40 +0.10 -0.05 0.016 +0.004 -0.003 E 0.1250.075 0.0050.003 F 2.9 MAX. 0.115 MAX. G 2.50 0.098 H 10.30.3 0.406 +0.012 -0.013 I 7.2 0.283 J 1.6 0.063 K 0.15 +0.10 -0.05 0.006 +0.004 -0.002 L 0.80.2 0.031 +0.009 -0.008 M 0.12 0.005 N 0.15 0.006 P 3 +7 -3 3 +7 -3 P20GM-50-375B-4 21 PD6121, 6122 (2) Package for the PD6122 24 PIN PLASTIC SOP (375 mil) 24 13 P detail of lead end 1 12 A H J G I E K F * B C D M L N M NOTE Each lead centerline is located within 0.12 mm (0.005 inch) of its true position (T.P.) at maximum material condition. ITEM MILLIMETERS INCHES A 15.54 MAX. 0.612 MAX. B 0.78 MAX. 0.031 MAX. C 1.27 (T.P.) 0.050 (T.P.) D 0.40 +0.10 -0.05 0.016 +0.004 -0.003 E 0.10.1 0.0040.004 F 2.9 MAX. 0.115 MAX. G 2.50 0.098 H 10.30.3 0.406 +0.012 -0.013 I 7.2 0.283 J 1.6 0.063 K 0.15 +0.10 -0.05 0.006 +0.004 -0.002 L 0.80.2 0.031 +0.009 -0.008 M 0.12 0.005 N 0.15 0.006 P 3 +7 -3 3 +7 -3 P24GM-50-375B-3 22 PD6121, 6122 11. RECOMMENDED SOLDERING CONDITIONS The following conditions (see table below) must be met when soldering this product. For more details, refer to the NEC document SEMICONDUCTOR DEVICE MOUNTING TECHNOLOGY MANUAL (IEI-1207). Please consult an NEC sales representative in case an other soldering process is used, or in case soldering is done under different conditions. Table 11-1. Soldering Conditions for Surface Mounting PD6121G-001: 20-pin plastic SOP (375 mil) * PD6121G-002: 20-pin plastic SOP (375 mil) PD6122G-001: 24-pin plastic SOP (375 mil) PD6122G-002: 24-pin plastic SOP (375 mil) Soldering Process Soldering Conditions Symbol Infrared ray reflow Peak temperature of package surface: 230 C, Reflow time: 30 seconds or less (210 C or higher), Number of reflow processes: 1 IR30-00-1 VPS Peak temperature of package surface: 215 C, Reflow time: 40 seconds or less (200 C or higher), Number of reflow processes: 1 VP15-00-1 Wave soldering Solder temperature: 260 C or lower, Reflow time: 10 seconds or less, Number of reflow processes: 1 WS60-00-1 Preheat temperature: 120 C or lower (at package surface) Partial heating Caution Pin temperature: 300 C or lower, Time: 3 seconds or less (per device side) -- Do not apply more than one soldering method at any one time, except for the partial heating method. 23 PD6121, 6122 * APPENDIX. REMOTE CONTROL TRANSMISSION IC AND MICROCONTROLLER LIST * Single-function remote control transmission ICs (NEC transmission format) Part number PD6121 Parameter PD6122 Operating voltage VDD = 2.0 to 3.3 V Operating clock fOSC = 400 to 500 kHz ceramic resonator Transmission format Leader 16-bit custom code Modulation method 8-bit data code PPM 0 ***** 8-bit data code 1 ***** 38-kHz carrier modulation (fosc = 455 kHz) Custom code 16-bit setting Data code 32 x 2 64 x 2 No. of keys 32 64 20-pin SOP (375 mil) 24-pin SOP (375 mil) Package Cautions 1. New custom codes are not available for the following standard products. PD6121G, 6122G Ver II standard products (-002) 2. If products other than listed in Caution 1 are used, please contact NEC for custom codes. 24 PD6121, 6122 * Single-Function 4-bit Single-Chip Microcontroller Part number * PD6133 PD6134 PD6604Note 1 Parameter ROM capacity 512 x 10 bits 1002 x 10 bits RAM capacity 32 x 4 bits Oscillator Ceramic oscillator S 0 (S-IN) Read with P 01 register (left shift instruction excluded, standby cancellation function provided) S 1/LED (S-OUT) I/O (standby cancellation function provided) Key matrix (without Di) 8 x 6 = 48 keys Timer clock f X /8, f X/16 Stack Also usable for RAM R F (1 level) Carrier frequency f X , f X /8, f X/12, high level f X /2, f X/16, f X /24 (software specified) Instruction execution time 8 s (f X = 1 MHz) Operating frequency f X = 300 kHz to 1 MHz Power supply voltage V DD = 1.8 to 3.6 V Operating ambient temperature TA = -40 to +85 C Charge/discharge function (NOP) Not provided (NOP instruction provided) Low voltage detector Low level is output to RESET pin at detection Package * 20-pin plastic SOP PROM version PD61F35 (flash EEPROM TM)Note 2 RC oscillator * 20-pin plastic SOP * 20-pin plastic shrink DIP * 20-pin plastic SOP * 20-pin plastic shrink SOP Notes 1. Under development 2. This product's pin configuration is the same as that of the 20-pin PD6133, 6134, and 6604, but the package is a 24-pin SOP shrink DIP package. Caution If using the NEC transmission format, please contact NEC for the custom code. 25 PD6121, 6122 * * 4-Bit Single-Chip Microcontroller for Programmable Remote Control Transmission Part number PD6600 PD6600A PD6124 PD6124A PD6125A Parameter ROM capacity 512 x 10 bits 1002 x 10 bits RAM capacity 32 x 5 bits Oscillator Ceramic oscillator S 0 (S-IN) Read with left shift instruction S 1/LED (S-OUT) Output Key matrix (without Di) 8 x 4 = 32 keys Timer clock f X/8 Stack Also usable for RAM (3 levels) Carrier frequency f X/8, f X /12 (mask option) Instruction execution time 16 s (f X = 500 kHz) Operating frequency f X = 400 kHz to 500 kHz Power supply voltage V DD = 2.0 to 3.6 V Operating ambient temperature T A = -20 to +75 C Charge/discharge function (NOP) Provided Low voltage detector Not provided Package * 20-pin plastic SOP * 20-pin plastic shrink DIP PROM version PD61P24 (one-time PROM) 8 x 8 = 64 keys VDD = 2.2 to 3.6 V Low level is output to S-OUT pin at detection VDD = 2.0 to 6.0 V VDD = 2.2 to 5.5 V VDD = 2.0 to 6.0 V Not provided Low level is ouput to S-OUT pin at detection Not provided Caution If using the NEC transmission format, please contact NEC for the custom code. 26 * 24-pin plastic SOP * 24-pin plastic shrink DIP -- PD6121, 6122 NOTES FOR CMOS DEVICES 1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS Note: Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it. 2 HANDLING OF UNUSED INPUT PINS FOR CMOS Note: No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to VDD or GND with a resistor, if it is considered to have a possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices. 3 STATUS BEFORE INITIALIZATION OF MOS DEVICES Note: Power-on does not necessarily define initial status of MOS device. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for devices having reset function. 27 PD6121, 6122 The application circuits and their parameters are for references only and are not intended for use in actual design-in's. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customer must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices in "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact NEC Sales Representative in advance. Anti-radioactive design is not implemented in this product. M4 94.11 28