DOCUMENT NUMBER NCD-62B2-02 SSCF-2P1 Series SC DUPLEX HOUSING (0.9mm / Push-pull Type) TECHNICAL SPECIFICATIONS Seiko Instruments Inc. Components Sales Dept. 8, Nakase 1-Chome Mihama-ku, Chiba-shi, Chiba-ken 261 JAPAN Telephone : 043-211-1214 -1215 Facsimile : 043-211-8035 SSCF-2P1 Series SC DUPLEX HOUSING ( 0.9mm / Push-pull Type ) TECHNICAL SPECIFICATIONS Document Number NCD-62B2-02 NCD-62B2-01 NCD-62B2-02 February 1996 March 1996 Copyright 1996 by Seiko Instruments Inc. All right reserved. The information contained herein shall not reproduced or disclosed to any third party without the express written consent of SII. The Specifications contained herein are subject to change without notice. SII is a trademark of Seiko Instruments Inc. Please address any questions, comments, and suggestions to: Seiko Instruments USA Inc. Seiko Instruments GmbH Electronics Components Division 2990 West Lomita Boulevard Torrance, CA 90505, U.S.A. Phone: 310-517-7780 Fax: 310-517-7792 OFC Division Siemensstrae 9b D-63263 Neu-Isenburg, Germany Phone: 06102-297-0 Fax: 06102-297-211 Seiko Instruments (H.K.) Ltd. Seiko Instruments Taiwan Inc. Sales Department 4th & 5th Floor, Wyler Center 2 200 Tai Lin Pai Road, Kwai Chung N.T., Kowloon, Hong Kong Phone: 852-2421-8611 Fax: 852-2480-5479 Sales Department 5F-1, No.99, Sec. 2, Chung Shan Rd. Taipei 104, Taiwan, R.O.C. Phone: 02-563-5001, 523-5111 Fax: 02-521-9519 Seiko Instruments Singapore pte. Ltd. 2, Marsiling Lane, Woodlands New Town, Singapore, 2573, Singapore Phone: 65-2691370 Fax: 65-2699729 ii TABLE OF CONTENTS Section 1. 1.1 Page PROVISION 1 Application Limit 1 2. PARTS NUMBER 1 3. GENERAL SPECIFICATIONS 2 3.1 Parts and Materials 2 3.2 Physical Dimensions 2 3.3 General Tolerances 2 4. PACKING 3 Table Table 1 Parts Number 1 Table 2 Parts and Materials 2 Table 3 General Tolerance 2 Figure Figure 1 Figure 2 to 7 SSCF-2P1 Housing 4 Part Dimensions 5 to 7 iii iv 1. PROVISION 1.1 Application Limit These specifications apply to the SSCF-2P1 SC DUPLEX HOUSING ( 0.9mm / Pushpull Type ) supplied by SII. 2. PARTS NUMBER Parts Number of the Housing is Shown in Table 1. Table 1 Parts Number 1 3. GENERAL SPECIFICATIONS 3.1 Parts and Materials Parts and the Materials are shown in Table 2. Table 2 Parts and Materials No. Part Name Q'ty Material Notes Grip 1 Plastics Blue , UL94 V-0 Plug frame 2 Plastics White , UL94 V-0 Spring 2 Stainless Steel Stop ring 2 Brass Nickel Plating Hood 2 Synthetic Rubber Hood Color Shows Table 1, UL94 V-0. Cap 2 PVC Blue - - 3.2 Physical Dimensions Figure 1 shows the assembled state of SSCF-2P1. Figure 2 to 7 show the part dimension. * Compatible with NTT SCF-2PH plug housing 3.3 General Tolerances Permissible deviation in dimensions without tolerance indication is in accordance with JIS B 0405 class m, as shown in Table 3. Table 3 General Tolerance (JIS B 0405 class m) Basic size step (mm) Over Under 0.5 3 6 30 Permissible deviation (mm) 0.1 0.1 0.2 0.3 3 6 30 120 2 4. PACKING The product is packed to prevent damage during shipping. 3 note.1: This drawing Shows the Tentatively assembled condition. In practice, the housing is not assembled like this. note.2: This drawing does not include Caps. Unit: mm Figure 1 SSCF-2P1 HOUSING 4 Unit: mm Figure 2 Grip Unit: mm Figure 3 Plug frame 5 Unit: mm Figure 4 Spring Unit: mm Figure 5 Stop ring 6 Unit: mm Figure 6 Hood Unit: mm Figure 7 Cap 7