INTEGRATED CIRCUITS 80C32/87C52 CMOS single-chip 8-bit microcontrollers Product specification IC20 Data Handbook 1996 Aug 16 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers DESCRIPTION 80C32/87C52 PIN CONFIGURATIONS The Philips 80C32/87C52 is a high-performance microcontroller fabricated with Philips high-density CMOS technology. The Philips CMOS technology combines the high speed and density characteristics of HMOS with the low power attributes of CMOS. Philips epitaxial substrate minimizes latch-up sensitivity. The 87C52 contains an 8k x 8 EPROM and the 80C32 is ROMless. Both contain a 256 x 8 RAM, 32 I/O lines, three 16-bit counter/timers, a six-source, two-priority level nested interrupt structure, a serial I/O port for either multi-processor communications, I/O expansion or full duplex UART, and on-chip oscillator and clock circuits. In addition, the 80C32/87C52 has two software selectable modes of power reduction--idle mode and power-down mode. The idle mode freezes the CPU while allowing the RAM, timers, serial port, and interrupt system to continue functioning. The power-down mode saves the RAM contents but freezes the oscillator, causing all other chip functions to be inoperative. P1.0/T2 1 40 VDD P1.1/T2EX 2 39 P0.0/AD0 P1.2 3 38 P0.1/AD1 P1.3 4 37 P0.2/AD2 P1.4 5 36 P0.3/AD3 P1.5 6 35 P0.4/AD4 P1.6 7 34 P0.5/AD5 P1.7 8 33 P0.6/AD6 RST See 80C52/80C54/80C58 datasheet for ROM device specifications. FEATURES * 80C51 based architecture * 8032 compatible - 8k x 8 EPROM (87C52) - ROMless (80C32) - 256 x 8 RAM 9 RxD/P3.0 10 TxD/P3.1 11 CERAMIC AND PLASTIC DUAL IN-LINE PACKAGE 32 P0.7/AD7 31 EA/V PP 30 ALE/PROG INT0/P3.2 12 29 PSEN INT1/P3.3 13 28 P2.7/A15 T0/P3.4 14 27 P2.6/A14 T1/P3.5 15 26 P2.5/A13 WR/P3.6 16 25 P2.4/A12 RD/P3.7 17 24 P2.3/A11 XTAL2 18 23 P2.2/A10 XTAL1 19 22 P2.1/A9 VSS 20 21 P2.0/A8 SU00060 - Three 16-bit counter/timers - Full duplex serial channel - Boolean processor * Memory addressing capability - 64k ROM and 64k RAM * Power control modes: - Idle mode - Power-down mode * CMOS and TTL compatible * Three speed ranges: - 3.5 to 16MHz - 3.5 to 24MHz - 3.5 to 33MHz * Five package styles * Extended temperature ranges * OTP package available 1996 Aug 16 2 853-1562 17195 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 ORDERING INFORMATION ROMless EPROM1 TEMPERATURE RANGE C AND PACKAGE FREQ MHz DRAWING NUMBER P80C32EBP N P87C52EBP N OTP 0 to +70, Plastic Dual In-line Package 16 SOT129-1 P80C32EBA A P87C52EBA A OTP 0 to +70, Plastic Leaded Chip Carrier 16 SOT187-2 P87C52EBF FA UV 0 to +70, Ceramic Dual In-line Package 16 0590B P87C52EBL KA UV 0 to +70, Ceramic Leaded Chip Carrier 16 1472A P80C32EBB B P87C52EBB B OTP 0 to +70, Plastic Quad Flat Pack 16 SOT307-2 P80C32EFP N P87C52EFP N OTP -40 to +85, Plastic Dual In-line Package 16 SOT129-1 P80C32EFA A P87C52EFA A OTP -40 to +85, Plastic Leaded Chip Carrier 16 SOT187-2 P87C52EFF FA UV -40 to +85, Ceramic Dual In-line Package 16 0590B P80C32EFB B P87C52EFB B OTP -40 to +85, Plastic Quad Flat Pack 16 SOT307-2 P80C32IBP N P87C52IBP N OTP 0 to +70, Plastic Dual In-line Package 24 SOT129-1 P80C32IBA A P87C52IBA A OTP 0 to +70, Plastic Leaded Chip Carrier 24 SOT187-2 0 to +70, Plastic Quad Flat Pack 24 SOT307-2 P80C32IBB B P87C52IBF FA UV 0 to +70, Ceramic Dual In-line Package 24 0590B P87C52IBL KA UV 0 to +70, Ceramic Leaded Chip Carrier 24 1472A P80C32IFP N P87C52IFP N OTP -40 to +85, Plastic Dual In-line Package 24 SOT129-1 P80C32IFA A P87C52IFA A OTP -40 to +85, Plastic Leaded Chip Carrier 24 SOT187-2 -40 to +85, Plastic Quad Flat Pack 24 SOT307-2 -40 to +85, Ceramic Dual In-line Package 24 0590B P80C32NBA A 0 to +70, Plastic Leaded Chip Carrier 33 SOT187-2 P80C32NBP N 0 to +70, Plastic Dual In-line Package 33 SOT129-1 P80C32NBB B 0 to +70, Plastic Quad Flat Pack 33 SOT307-2 P80C32NFA A -40 to +85, Plastic Leaded Chip Carrier 33 SOT187-2 P80C32NFP N -40 to +85, Plastic Dual In-line Package 33 SOT129-1 P80C32NFB B -40 to +85, Plastic Quad Flat Pack 33 SOT307-2 P80C32IFB B P87C52IFF FA UV NOTE: 1. OTP = One Time Programmable EPROM. UV = UV erasable EPROM 2. For 33MHz ROM 80C52 operation, see 80C52/80C54/80C58 data sheet. 1996 Aug 16 3 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers CERAMIC AND PLASTIC LEADED CHIP CARRIER PIN FUNCTIONS 80C32/87C52 PLASTIC QUAD FLAT PACK PIN FUNCTIONS 44 6 1 34 40 7 39 1 33 PQFP LCC 11 17 18 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Function NC* T2/P1.0 T2EX/P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 RST RxD/P3.0 NC* TxD/P3.1 INT0/P3.2 INT1/P3.3 Pin 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 12 28 Pin 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Function T0/P3.4 T1/P3.5 WR/P3.6 RD/P3.7 XTAL2 XTAL1 VSS NC* P2.0/A8 P2.1/A9 P2.2/A10 P2.3/A11 P2.4/A12 P2.5/A13 P2.6/A14 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Function P2.7/A15 PSEN ALE/PROG NC* EA/VPP P0.7/AD7 P0.6/AD6 P0.5/AD5 P0.4/AD4 P0.3/AD3 P0.2/AD2 P0.1/AD1 P0.0/AD0 VCC * DO NOT CONNECT VCC VSS PORT 0 XTAL1 ADDRESS AND DATA BUS XTAL2 1996 Aug 16 PORT 2 ALE/PROG PORT 3 SECONDARY FUNCTIONS PSEN PORT 1 T2 T2EX RST EA/VPP Function P1.5 P1.6 P1.7 RST RxD/P3.0 NC* TxD/P3.1 INT0/P3.2 INT1/P3.3 T0/P3.4 T1/P3.5 WR/P3.6 RD/P3.7 XTAL2 XTAL1 * DO NOT CONNECT SU00061 LOGIC SYMBOL RxD TxD INT0 INT1 T0 T1 WR RD 23 29 ADDRESS BUS SU00063 4 Pin 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 22 Function VSS NC* P2.0/A8 P2.1/A9 P2.2/A10 P2.3/A11 P2.4/A12 P2.5/A13 P2.6/A14 P2.7/A15 PSEN ALE/PROG NC* EA/VPP P0.7/AD7 Pin 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Function P0.6/AD6 P0.5/AD5 P0.4/AD4 P0.3/AD3 P0.2/AD2 P0.1/AD1 P0.0/AD0 VCC NC* T2/P1.0 T2EX/P1.1 P1.2 P1.3 P1.4 SU00062 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 BLOCK DIAGRAM P0.0-P0.7 P2.0-P2.7 PORT 0 DRIVERS PORT 2 DRIVERS VCC VSS RAM ADDR REGISTER PORT 0 LATCH RAM B REGISTER ROM/ EPROM PORT 2 LATCH STACK POINTER ACC PROGRAM ADDRESS REGISTER TMP1 TMP2 ALU PCON SCON TMOD TCON T2CON TH0 TL0 TH1 TL1 TH2 TL2 RCAP2H IE IP RCAP2L SBUF PSW INTERRUPT, SERIAL PORT AND TIMER BLOCKS BUFFER PC INCREMENTER PSEN ALE EA TIMING AND CONTROL RST INSTRUCTION REGISTER PROGRAM COUNTER PD DPTR PORT 1 LATCH PORT 3 LATCH PORT 1 DRIVERS PORT 3 DRIVERS P1.0-P1.7 P3.0-P3.7 OSCILLATOR XTAL1 XTAL2 SU00064 1996 Aug 16 5 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers Table 1. SYMBOL 80C32/87C52 8XC52 Special Function Registers DESCRIPTION DIRECT BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION ADDRESS MSB LSB RESET VALUE ACC* Accumulator E0H E7 E6 E5 E4 E3 E2 E1 E0 00H B* B register F0H F7 F6 F5 F4 F3 F2 F1 F0 00H DPTR: DPH DPL Data pointer (2 bytes) Data pointer high Data pointer low 83H 82H IE* Interrupt enable A8H IP* Interrupt priority B8H P0* Port 0 80H P1* Port 1 90H P2* Port 2 A0H 00H 00H AF AE AD AC AB AA A9 A8 EA - ET2 ES ET1 EX1 ET0 EX0 BF BE BD BC BB BA B9 B8 - - PT2 PS PT1 PX1 PT0 PX0 87 86 85 84 83 82 81 80 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 97 96 95 94 93 92 91 90 - - - - - - T2EX T2 A7 A6 A5 A4 A3 A2 A1 A0 A15 A14 A13 A12 A11 A10 A9 A8 B7 B6 B5 B4 B3 B2 B1 B0 0x000000B xx000000B FFH FFH FFH P3* Port 3 B0H RD WR T1 T0 INT1 INT0 TxD RxD FFH PCON1 Power control 87H SMOD - - - GF1 GF0 PD IDL 0xxxxxxxB D7 D6 D5 D4 D3 D2 D1 D0 CY AC F0 RS1 RS0 OV - P PSW* Program status word D0H RCAP2H# RCAPL# Capture high Capture low CBH CAH 00H 00H SBUF Serial data buffer 99H xxxxxxxxB SCON* Serial controller 98H SP Stack pointer 81H 9F 9E 9D 9C 9B 9A 99 98 SM0 SM1 SM2 REN TB8 RB8 TI RI 8F 8E 8D 8C 8B 8A 89 88 TR1 TF0 TR0 IE1 IT1 IE0 IT0 00H 07H TCON* Timer control 88H TF1 CF CE CD CC CB CA C9 C8 T2CON*# Timer 2 control C8H TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2 CP/RL2 TH0 TH1 TH2# TL0 TL1 TL2# Timer high 0 Timer high 1 Timer high 2 Timer low 0 Timer low 1 Timer low 2 8CH 8DH CDH 8AH 8BH CCH 00H 00H 00H 00H 00H 00H 00H 00H TMOD Timer mode 89H GATE C/T M1 M0 GATE * Bit addressable # SFRs are modified from or added to the 80C51 SFRs. 1. Bits GF1, GF0, PD, and IDL of the PCON register are not implemented in the NMOS 8XC52. 1996 Aug 16 00H 6 C/T M1 M0 00H Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 PIN DESCRIPTION PIN NO. MNEMONIC DIP LCC QFP TYPE VSS 20 22 16 I Ground: 0V reference. VCC 40 44 38 I Power Supply: This is the power supply voltage for normal, idle, and power-down operation. 39-32 43-36 37-30 I/O Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to them float and can be used as high-impedance inputs. Port 0 is also the multiplexed low-order address and data bus during accesses to external program and data memory. In this application, it uses strong internal pull-ups when emitting 1s. Port 0 also outputs the code bytes during program verification in the 87C52. External pull-ups are required during program verification. 1-8 2-9 40-44 1-3 I/O 1 2 2 3 40 41 I I Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 1 pins that are externally pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: IIL). Pins P1.0 and P1.1 also. Port 1 also receives the low-order address byte during program memory verification. Port 1 also serves alternate functions for timer 2: T2 (P1.0): Timer/counter 2 external count input. T2EX (P1.1): Timer/counter 2 trigger input. P2.0-P2.7 21-28 24-31 18-25 I/O Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 2 pins that are externally being pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: IIL). Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX @DPTR). In this application, it uses strong internal pull-ups when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOV @Ri), port 2 emits the contents of the P2 special function register. P3.0-P3.7 10-17 11, 13-19 5, 7-13 I/O 10 11 12 13 14 15 16 17 11 13 14 15 16 17 18 19 5 7 8 9 10 11 12 13 I O I I I I O O Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 3 pins that are externally being pulled low will source current because of the pull-ups. (See DC Electrical Characteristics: IIL). Port 3 also serves the special features of the 80C51 family, as listed below: RxD (P3.0): Serial input port TxD (P3.1): Serial output port INT0 (P3.2): External interrupt INT1 (P3.3): External interrupt T0 (P3.4): Timer 0 external input T1 (P3.5): Timer 1 external input WR (P3.6): External data memory write strobe RD (P3.7): External data memory read strobe RST 9 10 4 I Reset: A high on this pin for two machine cycles while the oscillator is running, resets the device. An internal diffused resistor to VSS permits a power-on reset using only an external capacitor to VCC. ALE/PROG 30 33 27 I/O Address Latch Enable/Program Pulse: Output pulse for latching the low byte of the address during an access to external memory. In normal operation, ALE is emitted at a constant rate of 1/6 the oscillator frequency, and can be used for external timing or clocking. Note that one ALE pulse is skipped during each access to external data memory. This pin is also the program pulse input (PROG) during EPROM programming. PSEN 29 32 26 O Program Store Enable: The read strobe to external program memory. When the device is executing code from the external program memory, PSEN is activated twice each machine cycle, except that two PSEN activations are skipped during each access to external data memory. PSEN is not activated during fetches from internal program memory. EA/VPP 31 35 29 I External Access Enable/Programming Supply Voltage: EA must be externally held low to enable the device to fetch code from external program memory locations 0000H to 1FFFH. If EA is held high, the device executes from internal program memory unless the program counter contains an address greater than 1FFFH. This pin also receives the 12.75V programming supply voltage (VPP) during EPROM programming. XTAL1 19 21 15 I Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator circuits. XTAL2 18 20 14 O Crystal 2: Output from the inverting oscillator amplifier. P0.0-0.7 P1.0-P1.7 1996 Aug 16 NAME AND FUNCTION 7 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 transition at external input T2EX will also trigger the 16-bit reload and set EXF2. The auto-reload mode is illustrated in Figure 3. DIFFERENCES FROM THE 80C51 Special Function Registers The baud rate generation mode is selected by RCLK = 1 and/or TCLK = 1. It will be described in conjunction with the serial port. The special function register space is the same as the 80C51 except that the 80C32/87C52 contains the additional special function registers T2CON, RCAP2L, RCAP2H, TL2, and TH2. Since the standard 80C51 on-chip functions are identical in the 8XC52, the SFR locations, bit locations, and operation are likewise identical. The only exceptions are in the interrupt mode and interrupt priority SFRs (see Table 1). Serial Port The serial port of the 8XC52 is identical to that of the 80C51 except that counter/timer 2 can be used to generate baud rates. In the 8XC52, Timer 2 is selected as the baud rate generator by setting TCLK and/or RCLK in T2CON (see Figure 1). Note that the baud rate for transmit and receive can be simultaneously different. Setting RCLK and/or TCLK puts Timer into its baud rate generator mode, as shown in Figure 4. Timer/Counters In addition to timer/counters 0 and 1 of the 80C51, the 80C32/87C52 contains timer/counter 2. Like timers 0 and 1, timer 2 can operate as either an event timer or as an event counter. This is selected by bit C/T2 in the special function register T2CON (see Figure 1). It has three operating modes: capture, auto-load, and baud rate generator, which are selected by bits in the T2CON as shown in Table 2. The baud rate generator mode is similar to the auto-reload mode, in that a rollover in TH2 causes the Timer 2 registers to be reloaded with the 16-bit value in registers RCAP2H and RCAP2L, which are preset by software. In the Capture Mode there are two options which are selected by bit EXEN2 in T2CON. If EXEN2 = 0, then Timer 2 is a 16-bit timer or counter which upon overflowing sets bit TF2, the Timer 2 overflow bit, which can be used to generate an interrupt. If EXEN2 = 1, then Timer 2 still does the above, but with the added feature that a 1-to-0 transition at external input T2EX causes the current value in the Timer 2 registers, TL2 and TH2, to be captured into registers RCAP2L and RCAP2H, respectively. (RCAP2L and RCAP2H are new special function registers in the 80C52.) In addition, the transition at T2EX causes bit EXF2 in T2CON to be set, and EXF2 like TF2 can generate an interrupt. The Capture Mode is illustrated in Figure 2. Now, the baud rates in Modes 1 and 3 are determined by Timer 2's overflow rate as follows: Modes 1, 3 Baud Rate Timer 2 Overflow Rate 16 The timer can be configured for either "timer" or "counter" operation. In the most typical applications, it is configured for "timer" operation (C/T2 = 0). "Timer" operation is a little different for Timer 2 when it's being used as a baud rate generator. Normally, as a timer it would increment every machine cycle (thus at 1/12 the oscillator frequency). As a baud rate generator, however, it increments every state time (thus at 1/2 the oscillator frequency). In that case the baud rate is given by the formula: In the auto-reload mode, there are again two options, which are selected by bit EXEN2 in T2CON. If EXEN2 = 0, then when Timer 2 rolls over it not only sets TF2 but also causes the Timer 2 registers to be reloaded with the 16-bit value in registers RCAP2L and RCAP2H, which are preset by software. If EXEN2 = 1, then Timer 2 still does the above, but with the added feature that a 1-to-0 Modes 1, 3 Baud Rate where (RCAP2H, RCAP2L) is the content of RCAP2H and RCAP2L taken as a 16-bit unsigned integer. (MSB) TF2 Symbol Position Oscillator Frequency 32 [65536 (RCAP2H, RCAP2L)] (LSB) EXF2 RCLK TCLK EXEN2 TR2 C/T2 CP/RL2 Name and Significance TF2 T2CON.7 Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set when either RCLK or TCLK = 1. EXF2 T2CON.6 Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and EXEN2 = 1. When Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2 interrupt routine. EXF2 must be cleared by software. RCLK T2CON.5 Receive clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its receive clock in modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for the receive clock. TCLK T2CON.4 Transmit clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock in modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock. EXEN2 T2CON.3 Timer 2 external enable flag. When set, allows a capture or reload to occur as a result of a negative transition on T2EX if Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to ignore events at T2EX. TR2 T2CON.2 Start/stop control for Timer 2. A logic 1 starts the timer. C/T2 T2CON.1 Timer or counter select. (Timer 2) 0 = Internal timer (OSC/12) 1 = External event counter (falling edge triggered). CP/RL2 T2CON.0 Capture/Reload flag. When set, captures will occur on negative transitions at T2EX if EXEN2 = 1. When cleared, auto-reloads will occur either with Timer 2 overflows or negative transitions at T2EX when EXEN2 = 1. When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is forced to auto-reload on Timer 2 overflow. SU00065 Figure 1. Timer/Counter 2 (T2CON) Control Register 1996 Aug 16 8 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers OSC 80C32/87C52 / 12 C/T2 = 0 TL2 (8-bits) TH2 (8-bits) TF2 C/T2 = 1 T2 Pin Control TR2 Capture Transition Detector Timer 2 Interrupt RCAP2L RCAP2H T2EX Pin EXF2 Control EXEN2 SU00066 Figure 2. Timer 2 in Capture Mode OSC / 12 C/T2 = 0 TL2 (8-BITS) TH2 (8-BITS) C/T2 = 1 T2 PIN CONTROL TR2 RELOAD TRANSITION DETECTOR RCAP2L RCAP2H TF2 TIMER 2 INTERRUPT T2EX PIN EXF2 CONTROL EXEN2 SU00067 Figure 3. Timer 2 in Auto-Reload Mode 1996 Aug 16 9 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 Timer 1 Overflow /2 NOTE: OSC. Freq. is divided by 2, not 12. "0" /2 OSC "1" C/T2 = 0 SMOD TL2 (8-bits) "1" TH2 (8-bits) "0" RCLK C/T2 = 1 T2 Pin Control / 16 "1" TR2 Reload Transition Detector RCAP2L T2EX Pin RX Clock "0" TCLK RCAP2H / 16 TX Clock Timer 2 Interrupt EXF2 Control EXEN2 Note availability of additional external interrupt. SU00068 Figure 4. Timer 2 in Baud Rate Generator Mode Table 2. Timer 2 Operating Modes RCLK + TCLK CP/RL2 TR2 0 0 1 16-bit Auto-reload MODE 0 1 1 16-bit Capture 1 X 1 Baud rate generator X X 0 (off) Timer 2 as a baud rate generator is shown in Figure 4. This figure is valid only if RCLK + TCLK = 1 in T2CON. Note that a rollover in TH2 does not set TF2, and will not generate an interrupt. Therefore, the Timer 2 interrupt does not have to be disabled when Timer 2 is in the baud rate generator mode. Note too, that if EXEN2 is set, a 1-to-0 transition in T2EX will set EXF2 but will not cause a reload from (RCAP2H, RCAP2L) to (TH2, TL2). Thus when Timer 2 is in use as a baud rate generator, T2EX can be used as an extra external interrupt, if desired. Timer/Counter 2 Set-up Except for the baud rate generator mode, the values given for T2CON do not include the setting of the TR2 bit. Therefore, bit TR2 must be set, separately, to turn the timer on. See Table 3 for set-up of timer 2 as a timer. See Table 4 for set-up of timer 2 as a counter. Using Timer/Counter 2 to Generate Baud Rates For this purpose, Timer 2 must be used in the baud rate generating mode. If Timer 2 is being clocked through pin T2 (P1.0) the baud rate is: It should be noted that when Timer 2 is running (TR2 = 1) in "timer" function in the baud rate generator mode, one should not try to read or write TH2 or TL2. Under these conditions the timer is being incremented every state time, and the results of a read or write may not be accurate. The RCAP registers may be read, but should not be written to, because a write might overlap a reload and cause write and/or reload errors. Turn the timer off (clear TR2) before accessing the Timer 2 or RCAP registers, in this case. Baud Rate Timer 2 Overflow Rate 16 And if it is being clocked internally, the baud rate is: Baud Rate Oscillator Frequency 32 [65536 (RCAP2H, RCAP2L)] To obtain the reload value for RCAP2H and RCA02L, the above equation can be rewritten as: RCAP2H, RCAP2L 65536 1996 Aug 16 10 Oscillator Frequency 32 Baud Rate Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 by hardware. That is, interrupts can be generated or pending interrupts can be canceled in software. Interrupts The 80C32/87C52 has 6 interrupt sources. All except TF2 and EXF2 are identical sources to those in the 80C51. The interrupt vector addresses and the interrupt priority for requests in the same priority level are given in the following: The Interrupt Enable Register and the Interrupt Priority Register are modified to include the additional 80C32/87C52 interrupt sources. The operation of these registers is identical to the 80C51. Source Vector Priority Within Address Level IE0 0003H (highest) TF0 000BH IE1 0013H TF1 001BH RI + TI 0023H TF2 + EXF2 002BH (lowest) In the 80C32/87C52, the Timer 2 Interrupt is generated by the logical OR of TF2 and EXF2. Neither of these flags is cleared by hardware when the service routine is vectored to. In fact, the service routine may have to determine whether it was TF2 or EXF2 that generated the interrupt, and the bit will have to be cleared in software. 1. 2. 3. 4. 5. 6. All of the bits that generate interrupts can be set or cleared by software, with the same result as though it has been set or cleared Note that they are identical to those in the 80C51 except for the addition of the Timer 2 (TF1 and EXF2) interrupt at 002BH and at the lowest priority within a level. Table 3. Timer 2 as a Timer MODE T2CON INTERNAL CONTROL (Note 1) EXTERNAL CONTROL (Note 2) 16-bit Auto-Reload 00H 08H 16-bit Capture 01H 09H Baud rate generator receive and transmit same baud rate 34H 36H Receive only 24H 26H Transmit only 14H 16H Table 4. Timer 2 as a Counter MODE TMOD 16-bit INTERNAL CONTROL (Note 1) EXTERNAL CONTROL (Note 2) 02H 0AH Auto-Reload 03H 0BH NOTES: 1. Capture/reload occurs only on timer/counter overflow. 2. Capture/reload occurs on timer/counter overflow and a 1-to-0 transition on T2EX (P1.1) pin except when timer 2 is used in the baud rate generator mode. 1996 Aug 16 11 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 of the special function registers remain intact during this mode. The idle mode can be terminated either by any enabled interrupt (at which time the process is picked up at the interrupt service routine and continued), or by a hardware reset which starts the processor in the same manner as a power-on reset. OSCILLATOR CHARACTERISTICS XTAL1 and XTAL2 are the input and output, respectively, of an inverting amplifier. The pins can be configured for use as an on-chip oscillator, as shown in the Logic Symbol, page 4. To drive the device from an external clock source, XTAL1 should be driven while XTAL2 is left unconnected. There are no requirements on the duty cycle of the external clock signal, because the input to the internal clock circuitry is through a divide-by-two flip-flop. However, minimum and maximum high and low times specified in the data sheet must be observed. POWER-DOWN MODE In the power-down mode, the oscillator is stopped and the instruction to invoke power-down is the last instruction executed. Only the contents of the on-chip RAM are preserved. A hardware reset is the only way to terminate the power-down mode. the control bits for the reduced power modes are in the special function register PCON. RESET A reset is accomplished by holding the RST pin high for at least two machine cycles (24 oscillator periods), while the oscillator is running. To insure a good power-up reset, the RST pin must be high long enough to allow the oscillator time to start up (normally a few milliseconds) plus two machine cycles. DESIGN CONSIDERATIONS At power-on, the voltage on VCC and RST must come up at the same time for a proper start-up. Table 5 shows the state of I/O ports during low current operating modes. IDLE MODE In idle mode, the CPU puts itself to sleep while all of the on-chip peripherals stay active. The instruction to invoke the idle mode is the last instruction executed in the normal operating mode before the idle mode is activated. The CPU contents, the on-chip RAM, and all As a precaution to coming out of an unexpected power down, INT0 and INT1 should be disabled prior to enterring power down. Table 5. External Pin Status During Idle and Power-Down Modes PROGRAM MEMORY ALE PSEN PORT 0 PORT 1 PORT 2 PORT 3 Idle MODE Internal 1 1 Data Data Data Data Idle External 1 1 Float Data Address Data Power-down Internal 0 0 Data Data Data Data Power-down External 0 0 Float Data Data Data 1996 Aug 16 12 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 Electrical Deviations from Commercial Specifications for Extended Temperature Range (87C52) DC and AC parameters not included here are the same as in the commercial temperature range table. DC ELECTRICAL CHARACTERISTICS Tamb = -40C to +85C, VCC = 5V 10%, VSS = 0V TEST SYMBOL PARAMETER LIMITS CONDITIONS MIN MAX UNIT -0.5 0.2VCC-0.15 V 0 0.2VCC-0.35 V 0.2VCC+1 VCC+0.5 V 0.7VCC+0.1 VCC+0.5 V VIL Input low voltage, except EA VIL1 Input low voltage to EA VIH Input high voltage, except XTAL1, RST VIH1 Input high voltage to XTAL1, RST IIL Logical 0 input current, ports 1, 2, 3 VIN = 0.45V -75 A ITL Logical 1-to-0 transition current, ports 1, 2, 3 VIN = 2.0V -750 A ICC Power supply current: Active mode Idle mode Power-down mode 32 5 50 mA mA A VCC = 4.5-5.5V, Frequency range = 3.5 to 16MHz ABSOLUTE MAXIMUM RATINGS1, 2, 3 PARAMETER Operating temperature under bias Storage temperature range Voltage on EA/VPP pin to VSS Voltage on any other pin to VSS RATING UNIT 0 to +70 or -40 to +85 C -65 to +150 C 0 to +13.0 V -0.5 to +6.5 V Maximum IOL per I/O pin 15 mA Power dissipation (based on package heat transfer limitations, not device power consumption) 1.5 W NOTES: 1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any conditions other than those described in the AC and DC Electrical Characteristics section of this specification is not implied. 2. This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maxima. 3. Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless otherwise noted. 1996 Aug 16 13 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 DC ELECTRICAL CHARACTERISTICS Tamb = 0C to +70C or -40C to +85C, VCC = 5V 10%, VSS = 0V (87C52) Tamb = 0C to +70C or -40C to +85C, VCC = 5V 10%, VSS = 0V (80C32) TEST SYMBOL VIL VIL1 VIH PARAMETER Input low voltage, except Input low voltage to CONDITIONS EA7 EA7 Input high voltage, except XTAL1, RST7 RST7 LIMITS MIN TYP1 MAX UNIT -0.5 0.2VCC-0.1 V 0 0.2VCC-0.3 V 0.2VCC+0.9 VCC+0.5 V 0.7VCC VIH1 Input high voltage, XTAL1, VCC+0.5 V VOL Output low voltage, ports 1, 2, 39 IOL = 1.6mA2 0.45 V VOL1 Output low voltage, port 0, ALE, PSEN9 IOL = 3.2mA2 0.45 V VOH Output high voltage, ports 1, 2, 3, ALE, PSEN3 IOH = -60A, IOH = -25A IOH = -10A 2.4 0.75VCC 0.9VCC V V V VOH1 Output high voltage (port 0 in external bus mode) IOH = -800A, IOH = -300A IOH = -80A 2.4 0.75VCC 0.9VCC V V V IIL Logical 0 input current, ports 1, 2, 37 ITL Logical 1-to-0 transition current, ports 1, 2, ILI Input leakage current, port 0 ICC Power supply current:7 Active mode @ 16MHz5 Idle mode @ 16MHz Power-down mode RRST CIO VIN = 0.45V -50 A See note 4 -650 A VIN = VIL or VIH 10 A 32 5 50 75 mA mA A A 300 k 15 pF 37 See note 6 11.5 1.3 3 Tamb = 0 to 70C Tamb = -40 to +85C Internal reset pull-down resistor Pin 50 capacitance10 NOTES: 1. Typical ratings are not guaranteed. The values listed are at room temperature, 5V. 2. Capacitive loading on ports 0 and 2 may cause spurious noise to be superimposed on the VOLs of ALE and ports 1 and 3. The noise is due to external bus capacitance discharging into the port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operations. In the worst cases (capacitive loading > 100pF), the noise pulse on the ALE pin may exceed 0.8V. In such cases, it may be desirable to qualify ALE with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input. IOL can exceed these conditions provided that no single output sinks more than 5mA and no more than two outputs exceed the test conditions. 3. Capacitive loading on ports 0 and 2 may cause the VOH on ALE and PSEN to momentarily fall below the 0.9VCC specification when the address bits are stabilizing. 4. Pins of ports 1, 2 and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its maximum value when VIN is approximately 2V. 5. ICCMAX at other frequencies is given by: Active mode: ICCMAX = 1.5 x FREQ + 8.0: Idle mode: ICCMAX = 0.14 x FREQ +2.31, where FREQ is the external oscillator frequency in MHz. ICCMAX is given in mA. See Figure 12. 6. See Figures 13 through 16 for ICC test conditions. 7. These values apply only to Tamb = 0C to +70C. For Tamb = -40C to +85C, see table on previous page. 8. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF. 9. Under steady state (non-transient) conditions, IOL must be externally limited as follows: 15mA (*NOTE: This is 85C specification.) Maximum IOL per port pin: 26mA Maximum IOL per 8-bit port: 67mA Maximum total IOL for all outputs: If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. 10. This limit is for plastic packages. For ceramic packages, the maximum limit is 20pF. 1996 Aug 16 14 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 AC ELECTRICAL CHARACTERISTICS Tamb = 0C to +70C or -40C to +85C, VCC = 5V 10%, VSS = 0V (87C52)1, 2, 3 16MHz CLOCK SYMBOL FIGURE 1/tCLCL 5 PARAMETER Oscillator frequency Speed versions MIN MAX :E VARIABLE CLOCK MIN MAX UNIT 3.5 16 MHz tLHLL 5 ALE pulse width 85 2tCLCL-40 ns tAVLL 5 Address valid to ALE low 22 tCLCL-40 ns tLLAX 5 Address hold after ALE low 32 tLLIV 5 ALE low to valid instruction in tLLPL 5 ALE low to PSEN low 32 tPLPH 5 PSEN pulse width 142 tPLIV 5 PSEN low to valid instruction in tPXIX 5 Input instruction hold after PSEN tPXIZ 5 Input instruction float after PSEN 37 tCLCL-25 ns tAVIV 5 Address to valid instruction in 207 5tCLCL-105 ns tPLAZ 5 PSEN low to address float 10 10 ns tCLCL-30 150 ns 4tCLCL-100 tCLCL-30 ns 3tCLCL-45 82 0 ns ns 3tCLCL-105 0 ns ns Data Memory tRLRH 6, 7 RD pulse width 275 6tCLCL-100 ns tWLWH 6, 7 WR pulse width 275 6tCLCL-100 ns tRLDV 6, 7 RD low to valid data in tRHDX 6, 7 Data hold after RD tRHDZ 6, 7 Data float after RD 65 2tCLCL-60 ns tLLDV 6, 7 ALE low to valid data in 350 8tCLCL-150 ns tAVDV 6, 7 Address to valid data in 397 9tCLCL-165 ns tLLWL 6, 7 ALE low to RD or WR low 137 3tCLCL+50 ns tAVWL 6, 7 Address valid to WR low or RD low 122 4tCLCL-130 ns tQVWX 6, 7 Data valid to WR transition 13 tCLCL-50 ns tWHQX 6, 7 Data hold after WR 13 tCLCL-50 ns tQVWH 7 Data valid to WR high 287 7tCLCL-150 ns tRLAZ 6, 7 RD low to address float tWHLH 6, 7 RD or WR high to ALE high 23 147 0 5tCLCL-165 0 239 3tCLCL-50 0 103 ns ns 0 ns tCLCL-40 tCLCL+40 ns 20 tCLCL-tCLCX ns 20 External Clock tCHCX 9 High time 20 tCLCX 9 Low time 20 tCLCL-tCHCX ns tCLCH 9 Rise time 20 20 ns tCHCL 9 Fall time 20 20 ns tXLXL 8 Serial port clock cycle time 750 12tCLCL ns tQVXH 8 Output data setup to clock rising edge 492 10tCLCL-133 ns tXHQX 8 Output data hold after clock rising edge 8 2tCLCL-117 ns tXHDX 8 Input data hold after clock rising edge 0 0 ns Shift Register tXHDV 8 Clock rising edge to input data valid 492 10tCLCL-133 ns NOTES: 1. Parameters are valid over operating temperature range unless otherwise specified. 2. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF. 3. Interfacing the 80C32/52 to devices with float times up to 45ns is permitted. This limited bus contention will not cause damage to Port 0 drivers. 4. See application note AN457 for external memory interface. 1996 Aug 16 15 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 AC ELECTRICAL CHARACTERISTICS Tamb = 0C to +70C or -40C to +85C, VCC = 5V 10%, VSS = 0V1, 2, 3 24MHz CLOCK SYMBOL FIGURE 1/tCLCL 5 PARAMETER MIN MAX Oscillator frequency Speed versions : I :N VARIABLE CLOCK MIN MAX 3.5 24 33MHz CLOCK MIN MAX 3.5 33 UNIT MHz tLHLL 5 ALE pulse width 43 2tCLCL-40 21 ns tAVLL 5 Address valid to ALE low 17 tCLCL-25 5 ns tLLAX 5 Address hold after ALE low 17 tCLCL-25 5 tLLIV 5 ALE low to valid instruction in tLLPL 5 ALE low to PSEN low 17 tCLCL-25 tPLPH 5 PSEN pulse width 80 3tCLCL-45 tPLIV 5 PSEN low to valid instruction in tPXIX 5 Input instruction hold after PSEN tPXIZ 5 Input instruction float after PSEN 17 tCLCL-25 5 ns tAVIV 5 Address to valid instruction in 128 5tCLCL-80 72 ns tPLAZ 5 PSEN low to address float 10 10 10 ns 102 4tCLCL-65 65 0 ns 56 5 3tCLCL-60 0 ns ns 46 ns 31 ns 0 ns Data Memory tRLRH 6, 7 RD pulse width 150 6tCLCL-100 tWLWH 6, 7 WR pulse width 150 tRLDV 6, 7 RD low to valid data in tRHDX 6, 7 Data hold after RD tRHDZ 6, 7 Data float after RD 55 2tCLCL-28 33 ns tLLDV 6, 7 ALE low to valid data in 183 8tCLCL-150 92 ns tAVDV 6, 7 Address to valid data in 108 ns tLLWL 6, 7 ALE low to RD or WR low 75 141 ns tAVWL 6, 7 Address valid to WR low or RD low 92 4tCLCL-75 46 ns tQVWX 6, 7 Data valid to WR transition 12 tCLCL-30 0.3 ns tWHQX 6, 7 Data hold after WR 17 tCLCL-25 5 ns Data valid to WR high 162 6tCLCL-100 118 0 0 7 tRLAZ 6, 7 RD low to address float tWHLH 6, 7 RD or WR high to ALE high 17 175 0 3tCLCL+50 7tCLCL-130 0 67 ns 62 9tCLCL-165 3tCLCL-50 ns 82 5tCLCL-90 210 tQVWH 82 41 ns 82 0 5 ns ns 0 ns 5 ns tCLCL-25 tCLCL+25 17 tCLCL-tCLCX ns 17 External Clock tCHCX 9 High time 17 tCLCX 9 Low time 17 tCLCL-tCHCX ns tCLCH 9 Rise time 5 5 ns tCHCL 9 Fall time 5 5 ns tXLXL 8 Serial port clock cycle time 505 12tCLCL 363 ns tQVXH 8 Output data setup to clock rising edge 283 10tCLCL-133 170 ns tXHQX 8 Output data hold after clock rising edge 3 2tCLCL-80 19 ns tXHDX 8 Input data hold after clock rising edge 0 0 0 ns Shift Register tXHDV 8 Clock rising edge to input data valid 283 10tCLCL-133 170 ns NOTES: 1. Parameters are valid over operating temperature range unless otherwise specified. 2. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF. 3. Interfacing the 8XC52 to devices with float times up to 45ns is permitted. This limited bus contention will not cause damage to Port 0 drivers. 4. Variable clock is specified for oscillator frequencies greater than 16MHz to 33MHz. For frequencies equal or less than 16MHz, see 16MHz "AC Electrial Characteristics", page 15. 1996 Aug 16 16 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 EXPLANATION OF THE AC SYMBOLS P - PSEN Q - Output data R - RD signal t - Time V - Valid W - WR signal X - No longer a valid logic level Z - Float Examples: tAVLL = Time for address valid to ALE low. tLLPL= Time for ALE low to PSEN low. Each timing symbol has five characters. The first character is always `t' (= time). The other characters, depending on their positions, indicate the name of a signal or the logical status of that signal. The designations are: A - Address C - Clock D - Input data H - Logic level high I - Instruction (program memory contents) L - Logic level low, or ALE tLHLL ALE tAVLL tLLPL tPLPH tLLIV tPLIV PSEN tLLAX A0-A7 PORT 0 tPXIZ tPLAZ tPXIX A0-A7 INSTR IN tAVIV PORT 2 A0-A15 A8-A15 SU00006 Figure 5. External Program Memory Read Cycle ALE tWHLH PSEN tLLDV tLLWL tRLRH RD tAVLL tLLAX tRLAZ PORT 0 tRHDZ tRLDV tRHDX A0-A7 FROM RI OR DPL DATA IN A0-A7 FROM PCL INSTR IN tAVWL tAVDV PORT 2 P2.0-P2.7 OR A8-A15 FROM DPF A0-A15 FROM PCH SU00025 Figure 6. External Data Memory Read Cycle 1996 Aug 16 17 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 ALE tWHLH PSEN tWLWH tLLWL WR tLLAX tAVLL A0-A7 FROM RI OR DPL PORT 0 tWHQX tQVWX DATA OUT A0-A7 FROM PCL INSTR IN tAVWL PORT 2 P2.0-P2.7 OR A8-A15 FROM DPF A0-A15 FROM PCH SU00069 Figure 7. External Data Memory Write Cycle INSTRUCTION 0 1 2 3 4 5 6 7 8 ALE tXLXL CLOCK tXHQX tQVXH OUTPUT DATA 0 1 2 WRITE TO SBUF 3 4 5 6 7 tXHDX tXHDV SET TI INPUT DATA VALID VALID VALID VALID VALID VALID VALID VALID CLEAR RI SET RI SU00027 Figure 8. Shift Register Mode Timing VCC-0.5 0.45V 0.7VCC 0.2VCC-0.1 tCHCL tCHCX tCLCH tCLCX tCLCL SU00009 Figure 9. External Clock Drive 1996 Aug 16 18 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers VCC-0.5 80C32/87C52 0.2VCC+0.9 0.2VCC-0.1 0.45V NOTE: AC inputs during testing are driven at VCC -0.5 for a logic `1' and 0.45V for a logic `0'. Timing measurements are made at VIH min for a logic `1' and VIL max for a logic `0'. SU00010 Figure 10. AC Testing Input/Output VLOAD+0.1V VLOAD VLOAD-0.1V VOH-0.1V TIMING REFERENCE POINTS VOL+0.1V NOTE: For timing purposes, a port is no longer floating when a 100mV change from load voltage occurs, and begins to float when a 100mV change from the loaded VOH/VOL level occurs. IOH/IOL 20mA. SU00011 Figure 11. Float Waveform 65 60 MAX ACTIVE MODE ICCMAX = 1.5 X FREQ. + 8.0 55 50 45 40 35 ICC mA 30 TYP ACTIVE MODE 25 20 15 10 MAX IDLE MODE 5 TYP IDLE MODE 4MHz 8MHz 12MHz 16MHz 20MHz 24MHz 28MHz 32MHz 36MHz FREQ AT XTAL1 Figure 12. ICC vs. FREQ Valid only within frequency specifications of the device under test 1996 Aug 16 19 SU00070B Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 VCC VCC ICC ICC VCC VCC VCC VCC RST RST VCC P0 P0 EA EA (NC) XTAL2 (NC) XTAL2 CLOCK SIGNAL XTAL1 CLOCK SIGNAL XTAL1 VSS VSS SU00719 SU00720 Figure 13. ICC Test Condition, Active Mode All other pins are disconnected VCC-0.5 Figure 14. ICC Test Condition, Idle Mode All other pins are disconnected 0.7VCC 0.2VCC-0.1 0.45V tCHCL tCHCX tCLCH tCLCX tCLCL SU00009 Figure 15. Clock Signal Waveform for ICC Tests in Active and Idle Modes tCLCH = tCHCL = 5ns VCC ICC VCC VCC RST P0 EA (NC) XTAL2 XTAL1 VSS SU00016 Figure 16. ICC Test Condition, Power Down Mode All other pins are disconnected. VCC = 2V to 5.5V 1996 Aug 16 20 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 Program Verification If security bit 2 has not been programmed, the on-chip program memory can be read out for program verification. The address of the program memory locations to be read is applied to ports 1 and 2 as shown in Figure 19. The other pins are held at the `Verify Code Data' levels indicated in Table 6. The contents of the address location will be emitted on port 0. External pull-ups are required on port 0 for this operation. EPROM CHARACTERISTICS The 87C52 is programmed by using a modified Quick-Pulse Programming algorithm. It differs from older methods in the value used for VPP (programming supply voltage) and in the width and number of the ALE/PROG pulses. The 87C52 contains two signature bytes that can be read and used by an EPROM programming system to identify the device. The signature bytes identify the device as an 87C52 manufactured by Philips. If the encryption table has been programmed, the data presented at port 0 will be the exclusive NOR of the program byte with one of the encryption bytes. The user will have to know the encryption table contents in order to correctly decode the verification data. The encryption table itself cannot be read out. Table 6 shows the logic levels for reading the signature byte, and for programming the program memory, the encryption table, and the security bits. The circuit configuration and waveforms for quick-pulse programming are shown in Figures 17 and 18. Figure 19 shows the circuit configuration for normal program memory verification. Reading the Signature Bytes The signature bytes are read by the same procedure as a normal verification of locations 030H and 031H, except that P3.6 and P3.7 need to be pulled to a logic low. The values are: (030H) = 15H indicates manufactured by Philips (031H) = 97H indicates 87C52 Quick-Pulse Programming The setup for microcontroller quick-pulse programming is shown in Figure 17. Note that the 87C52 is running with a 4 to 6MHz oscillator. The reason the oscillator needs to be running is that the device is executing internal address and program data transfers. Program/Verify Algorithms The address of the EPROM location to be programmed is applied to ports 1 and 2, as shown in Figure 17. The code byte to be programmed into that location is applied to port 0. RST, PSEN and pins of ports 2 and 3 specified in Table 6 are held at the `Program Code Data' levels indicated in Table 6. The ALE/PROG is pulsed low 25 times as shown in Figure 18. Any algorithm in agreement with the conditions listed in Table 6, and which satisfies the timing specifications, is suitable. Erasure Characteristics Erasure of the EPROM begins to occur when the chip is exposed to light with wavelengths shorter than approximately 4,000 angstroms. Since sunlight and fluorescent lighting have wavelengths in this range, exposure to these light sources over an extended time (about 1 week in sunlight, or 3 years in room level fluorescent lighting) could cause inadvertent erasure. For this and secondary effects, it is recommended that an opaque label be placed over the window. For elevated temperature or environments where solvents are being used, apply Kapton tape Fluorglas part number 2345-5, or equivalent. To program the encryption table, repeat the 25 pulse programming sequence for addresses 0 through 1FH, using the `Pgm Encryption Table' levels. Do not forget that after the encryption table is programmed, verification cycles will produce only encrypted data. To program the security bits, repeat the 25 pulse programming sequence using the `Pgm Security Bit' levels. After one security bit is programmed, further programming of the code memory and encryption table is disabled. However, the other security bit can still be programmed. The recommended erasure procedure is exposure to ultraviolet light (at 2537 angstroms) to an integrated dose of at least 15W-s/cm2. Exposing the EPROM to an ultraviolet lamp of 12,000W/cm2 rating for 20 to 39 minutes, at a distance of about 1 inch, should be sufficient. Note that the EA/VPP pin must not be allowed to go above the maximum specified VPP level for any amount of time. Even a narrow glitch above that voltage can cause permanent damage to the device. The VPP source should be well regulated and free of glitches and overshoot. Erasure leaves the array in an all 1s state. Table 6. EPROM Programming Modes RST PSEN ALE/PROG EA/VPP P2.7 P2.6 P3.7 P3.6 Read signature MODE 1 0 1 1 0 0 0 0 Program code data 1 0 0* VPP 1 0 1 1 Verify code data 1 0 1 1 0 0 1 1 Pgm encryption table 1 0 0* VPP 1 0 1 0 Pgm security bit 1 1 0 0* VPP 1 1 1 1 Pgm security bit 2 1 0 0* VPP 1 1 0 0 NOTES: 1. `0' = Valid low for that pin, `1' = valid high for that pin. 2. VPP = 12.75V 0.25V. 3. VCC = 5V10% during programming and verification. 4. *ALE/PROG receives 25 programming pulses while VPP is held at 12.75V. Each programming pulse is low for 100s (10s) and high for a minimum of 10s. Trademark phrase of Intel Corporation. 1996 Aug 16 21 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 +5V VCC A0-A7 P0 P1 1 RST EA/VPP 1 P3.6 ALE/PROG 1 87C52 P3.7 XTAL2 4-6MHz XTAL1 PGM DATA +12.75V 25 100s PULSES TO GROUND PSEN 0 P2.7 1 P2.6 0 A8-A12 P2.0-P2.4 VSS SU00071 Figure 17. Programming Configuration 25 PULSES 1 ALE/PROG: 0 10s MIN 1 ALE/PROG: 100s+10 0 SU00018 Figure 18. PROG Waveform +5V VCC A0-A7 P0 P1 PGM DATA 1 RST EA/VPP 1 1 P3.6 ALE/PROG 1 1 P3.7 PSEN 0 87C52 XTAL2 4-6MHz XTAL1 P2.7 0 ENABLE P2.6 0 P2.0-P2.4 A8-A12 VSS SU00072 Figure 19. Program Verification 1996 Aug 16 22 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 EPROM PROGRAMMING AND VERIFICATION CHARACTERISTICS Tamb = 21C to +27C, VCC = 5V10%, VSS = 0V (See Figure 20) PARAMETER SYMBOL MIN MAX UNIT 12.5 13.0 V 50 mA 6 MHz VPP Programming supply voltage IPP Programming supply current 1/tCLCL Oscillator frequency tAVGL Address setup to PROG low 48tCLCL tGHAX Address hold after PROG 48tCLCL tDVGL Data setup to PROG low 48tCLCL tGHDX Data hold after PROG 48tCLCL tEHSH P2.7 (ENABLE) high to VPP 48tCLCL tSHGL VPP setup to PROG low 10 s tGHSL VPP hold after PROG 10 s tGLGH PROG width 90 tAVQV Address to data valid 48tCLCL tELQZ ENABLE low to data valid 48tCLCL tEHQZ Data float after ENABLE 0 tGHGL PROG high to PROG low 10 4 PROGRAMMING* VERIFICATION* ADDRESS ADDRESS P1.0-P1.7 P2.0-P2.4 110 s 48tCLCL s tAVQV DATA IN PORT 0 DATA OUT tDVGL tAVGL tGHDX tGHAX ALE/PROG tGLGH tSHGL tGHGL tGHSL LOGIC 1 LOGIC 1 EA/VPP LOGIC 0 tEHSH tELQV tEHQZ P2.7 ENABLE SU00020 NOTE: * FOR PROGRAMMING VERIFICATION SEE FIGURE 17. FOR VERIFICATION CONDITIONS SEE FIGURE 19. Figure 20. EPROM Programming and Verification 1996 Aug 16 23 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers DIP40: plastic dual in-line package; 40 leads (600 mil) 1996 Aug 16 24 80C32/87C52 SOT129-1 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers PLCC44: plastic leaded chip carrier; 44 leads 1996 Aug 16 80C32/87C52 SOT187-2 25 1996 Aug 16 853-0590B 06688 26 SEATING PLANE -T- -D- 0.023 (0.58) 0.015 (0.38) 0.070 (1.78) 0.050 (1.27) T 0.100 (2.54) BSC E D 0.010 (0.254) 2.087 (53.01) 2.038 (51.77) SEE NOTE 6 0.098 (2.49) 0.040 (1.02) 0.165 (4.19) 0.125 (3.18) 0.015 (0.38) 0.010 (0.25) 0.055 (1.40) 0.020 (0.51) 0.175 (4.45) 0.145 (3.68) 0.695 (17.65) 0.600 (15.24) BSC 0.600 (15.24) (NOTE 4) 0.620 (15.75) 0.590 (14.99) (NOTE 4) 6. Denotes window location for EPROM products. 5. Pin numbers start with Pin #1 and continue counterclockwise to Pin #40 when viewed from the top. 0.225 (5.72) MAX. 0.598 (15.19) 0.571 (14.50) 2. Dimension and tolerancing per ANSI Y14. 5M-1982. 3. "T", "D", and "E" are reference datums on the body and include allowance for glass overrun and meniscus on the seal line, and lid to base mismatch. 4. These dimensions measured with the leads constrained to be perpendicular to plane T. NOTES: 1. Controlling dimension: Inches. Millimeters are shown in parentheses. 0590B PIN # 1 -E- 0.098 (2.49) 0.040 (1.02) Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 40-PIN (600 mils wide) CERAMIC DUAL IN-LINE (F) PACKAGE (WITH WINDOW (FA) PACKAGE) 1996 Aug 16 853-1472A 05854 27 SEE DETAIL B SEATING PLANE 4.83 (0.190) 3.94 (0.155) 8.13 (0.320) 7.37 (0.290) 8.13 (0.320) 7.37 (0.290) 12.7 (0.500) NOMINAL 40X 1.27 (0.050) 17.65 (0.656) 17.40 (0.685) 3 X 0.63 (0.025) R MIN. SEE DETAIL A 3 16.89 (0.665) 16.00 (0.630) 4.83 (0.190) 3.94 (0.155) SEATING PLANE 6 0.51 (0.02) X 45 6 0.38 (0.015) 0.482 (0.019 + 0.002) BASE PLANE 45 TYP. 4 PLACES 0.73 + 0.08 (0.029 + 0.003) SEATING PLANE DETAIL A TYP. ALL SIDES mm/(inch) 1.02 + 0.25 (0.040 + 0.010) 1.52 (0.060) REF. 1.27 (0.050) TYP. 17.65 (0.695) 17.40 (0.685) 3.05 (0.120) 2.29 (0.090) 0.25 (0.010) 0.15 (0.006) 0.15 (0.006) MIN. 0.25 (0.010) R MIN. + 5 -10 DETAIL B mm/(inch) 90 0.508 (0.020) R MIN. 0.076 (0.003) MIN. 6. Backside solder relief is optional and dimensions are for reference only. 5. All dimensions and tolerances include lead trim offset and lead plating finish. 3. Dimensions do not include glass protrusion. Glass protrusion to be 0.005 inches maximum on each side. 4. Controlling dimension millimeters. 2. UV window is optional. NOTES: 1. All dimensions and tolerances to conform to ANSI Y14.5-1982. 1472A 2 1.02 (0.040) X 45 CHAMFER 45 17.65 (0.695) 17.40 (0.685) 16.89 (0.665) 16.00 (0.630) 3 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 44-PIN CERQUAD J-BEND (K) PACKAGE Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 QFP44: plastic quad flat package; 44 leads (lead length 1.3 mm); body 10 x 10 x 1.75 mm 1996 Aug 16 28 SOT307-2 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers NOTES 1996 Aug 16 29 80C32/87C52 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C32/87C52 DEFINITIONS Data Sheet Identification Product Status Definition Objective Specification Formative or in Design This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. Preliminary Specification Preproduction Product This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product Specification Full Production This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product. Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088-3409 Telephone 800-234-7381 Philips Semiconductors and Philips Electronics North America Corporation register eligible circuits under the Semiconductor Chip Protection Act. Copyright Philips Electronics North America Corporation 1996 All rights reserved. Printed in U.S.A. INTEGRATED CIRCUITS 80C52/80C54/80C58 CMOS single-chip 8-bit microcontrollers Product specification IC20 Data Handbook 1996 Aug 16 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers DESCRIPTION 80C52/80C54/80C58 PIN CONFIGURATIONS The 80C52/80C54/80C58 Single-Chip 8-Bit Microcontroller is manufactured in an advanced CMOS process and is a derivative of the 80C51 microcontroller family. The 80C52/80C54/80C58 has the same instruction set as the 80C51. T2/P1.0 1 This device provides architectural enhancements that make it applicable in a variety of applications for general control systems. The 80C52 contains 8k x 8 ROM memory, the 80C54 contains 16k x 8 ROM memory, and 80C58 contains 32k x 8 ROM memory, a volatile 256 x 8 read/write data memory, four 8-bit I/O ports, three 16-bit timer/event counters, a multi-source, four-priority-level, nested interrupt structure, an enhanced UART and on-chip oscillator and timing circuits. For systems that require extra capability, the 80C52/54/58 can be expanded using standard TTL compatible memories and logic. 39 P0.0/AD0 P1.2 3 38 P0.1/AD1 P1.3 4 37 P0.2/AD2 P1.4 5 36 P0.3/AD3 P1.5 6 35 P0.4/AD4 P1.6 7 34 P0.5/AD5 P1.7 8 33 P0.6/AD6 RST 9 32 P0.7/AD7 RxD/P3.0 10 Its added features make it an even more powerful microcontroller for applications that require pulse width modulation, high-speed I/O and up/down counting capabilities such as motor control. It also has a more versatile serial channel that facilitates multiprocessor communications. TxD/P3.1 11 See 87C52/80C32 and 87C54/87C58 data sheets for EPROM and ROMless devices. FEATURES * 80C51 central processing unit * Full static operation * 8k x 8 ROM: 80C52; 16k x 8 ROM: 80C54; 32k x 8 ROM: 80C58; all capable of addressing external memory to 64k bytes - Two level program security system 40 VCC T2EX/P1.1 2 DUAL IN-LINE PACKAGE 31 EA 30 ALE INT0/P3.2 12 29 PSEN INT1/P3.3 13 28 P2.7/A15 T0/P3.4 14 27 P2.6/A14 T1/P3.5 15 26 P2.5/A13 WR/P3.6 16 25 P2.4/A12 RD/P3.7 17 24 P2.3/A11 XTAL2 18 23 P2.2/A10 XTAL1 19 22 P2.1/A9 VSS 20 21 P2.0/A8 SU00740 - 64 byte encryption array * 256 x 8 RAM, expandable externally to 64k bytes * Speed range up to 33MHz * Operating voltage 5V 10% * Three 16-bit timer/counters - T2 is an up/down counter * 6 interrupt sources * 4 level priority * Four 8-bit I/O ports * Full-duplex enhanced UART - Framing error detection - Automatic address recognition * Power control modes - Idle mode - Power-down mode * Once (On Circuit Emulation) Mode * Five package styles * Programmable clock out * Low EMI (Inhibit ALE) * Second DPTR register * Asynchronous port reset 1996 Aug 16 2 853-1470 17196 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 ORDERING INFORMATION ROM 8k x 8 ROM 16k x 8 ROM 32k x 8 TEMPERATURE RANGE C AND PACKAGE FREQ MHz DRAWING NUMBER P80C52EBPN P80C54EBPN P80C58EBPN 0 to +70, Plastic Dual In-line Package 16 SOT129-1 P80C52EBAA P80C54EBAA P80C58EBAA 0 to +70, Plastic Leaded Chip Carrier 16 SOT187-2 P80C52EBBB P80C54EBBB P80C58EBBB 0 to +70, Plastic Quad Flat Pack 16 SOT307-2 P80C52EFP N P80C54EFP N P80C58EFP N -40 to +85, Plastic Dual In-line Package 16 SOT129-1 P80C52EFA A P80C54EFA A P80C58EFA A -40 to +85, Plastic Leaded Chip Carrier 16 SOT187-2 P80C52EFB B P80C54EFB B P80C58EFB B -40 to +85, Plastic Quad Flat Pack 16 SOT307-2 P80C52IBP N P80C54IBP N P80C58IBP N 0 to +70, Plastic Dual In-line Package 24 SOT129-1 P80C52IBA A P80C54IBA A P80C58IBA A 0 to +70, Plastic Leaded Chip Carrier 24 SOT187-2 P80C52IBB B P80C54IBB B P80C58IBB B 0 to +70, Plastic Quad Flat Pack 24 SOT307-2 P80C52IFP N P80C54IFP N P80C58IFP N -40 to +85, Plastic Dual In-line Package 24 SOT129-1 P80C52IFA A P80C54IFA A P80C58IFA A -40 to +85, Plastic Leaded Chip Carrier 24 SOT187-2 P80C52IFB B P80C54IFB B P80C58IFB B -40 to +85, Plastic Quad Flat Pack 24 SOT307-2 P80C52NBAA P80C54NBAA P80C58NBAA 0 to +70, Plastic Leaded Chip Carrier 33 SOT187-2 P80C52NBPN P80C54NBPN P80C58NBPN 0 to +70, Plastic Dual In-line Package 33 SOT129-1 P80C52NBBB P80C54NBBB P80C58NBBB 0 to +70, Plastic Quad Flat Pack 33 SOT307-2 P80C52NFA A P80C54NFA A P80C58NFA A -40 to +85, Plastic Leaded Chip Carrier 33 SOT187-2 P80C52NFPN P80C54NFPN P80C58NFPN -40 to +85, Plastic Dual In-line Package 33 SOT129-1 P80C52NFBB P80C54NFBB P80C58NFBB -40 to +85, Plastic Quad Flat Pack 33 SOT307-2 LOGIC SYMBOL VCC VSS PORT 0 XTAL1 ADDRESS AND DATA BUS XTAL2 RST EA PORT 2 ALE RxD TxD INT0 INT1 T0 T1 WR RD PORT 3 SECONDARY FUNCTIONS PSEN PORT 1 T2 T2EX ADDRESS BUS SU00732 1996 Aug 16 3 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 BLOCK DIAGRAM P0.0-P0.7 P2.0-P2.7 PORT 0 DRIVERS PORT 2 DRIVERS VCC 8 8 VSS RAM ADDR REGISTER PORT 0 LATCH RAM PORT 2 LATCH ROM 16 B REGISTER STACK POINTER ACC PROGRAM ADDRESS REGISTER TMP1 TMP2 BUFFER ALU SFRs PC INCREMENTER TIMERS PSW 8 16 PSEN ALE EA TIMING AND CONTROL RST INSTRUCTION REGISTER PROGRAM COUNTER PD MULTIPLE DPTRs PORT 1 LATCH PORT 3 LATCH PORT 1 DRIVERS PORT 3 DRIVERS P1.0-P1.7 P3.0-P3.7 OSCILLATOR XTAL1 XTAL2 SU00733B 1996 Aug 16 4 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers Table 1. SYMBOL 80C52/80C54/80C58 80C52/80C54/80C58 Special Function Registers DESCRIPTION DIRECT ADDRESS BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION MSB LSB RESET VALUE ACC* Accumulator E0H E7 E6 E5 E4 E3 E2 E1 E0 00H AUXR# Auxiliary 8EH - - - - - - - AO xxxxxxx0B AUXR1# Auxiliary 1 A2H - - - - - - - DPS xxxxxxx0B B* B register F0H F7 F6 F5 F4 F3 F2 F1 F0 DPTR: DPH DPL Data Pointer (2 bytes) Data Pointer High Data Pointer Low 83H 82H IE* Interrupt Enable A8H IP* Interrupt Priority B8H IPH# Interrupt Priority High B7H P0* Port 0 80H 00H 00H 00H AF AE AD AC AB AA A9 A8 EA EC ET2 ES ET1 EX1 ET0 EX0 BF BE BD BC BB BA B9 B8 - - PT2 PS PT1 PX1 PT0 PX0 B7 B6 B5 B4 B3 B2 B1 B0 - - PT2H PSH PT1H PX1H PT0H PX0H 87 86 85 84 83 82 81 80 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 97 96 95 94 93 92 91 90 - - - - - T2EX T2 P1* Port 1 90H - A7 A6 A5 A4 A3 A2 A1 A0 P2* Port 2 A0H AD15 AD14 AD13 AD12 AD11 AD10 AD9 AD8 B7 B6 B5 B4 B3 B2 B1 B0 00H x0000000B x0000000B FFH FFH FFH P3* Port 3 B0H RD WR T1 T0 INT1 INT0 TxD RxD FFH PCON#1 Power Control 87H SMOD1 SMOD0 - POF2 GF1 GF0 PD IDL 00xx0000B D7 D6 D5 D4 D3 D2 D1 D0 PSW* Program Status Word D0H CY AC F0 RS1 RS0 OV - P RACAP2H# RACAP2L# Timer 2 Capture High Timer 2 Capture Low CBH CAH 00H 00H SADDR# SADEN# Slave Address Slave Address Mask A9H B9H 00H 00H SBUF Serial Data Buffer 99H SCON* Serial Control 98H SP Stack Pointer 81H xxxxxxxxB 9F 9E 9D 9C 9B 9A 99 98 SM0/FE SM1 SM2 REN TB8 RB8 TI RI 8F 8E 8D 8C 8B 8A 89 88 TR1 TF0 TR0 IE1 IT1 IE0 IT0 00H 07H TCON* Timer Control 88H TF1 CF CE CD CC CB CA C9 C8 T2CON* Timer 2 Control C8H TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2 CP/RL2 T2MOD# TH0 TH1 TH2# TL0 TL1 TL2# Timer 2 Mode Control Timer High 0 Timer High 1 Timer High 2 Timer Low 0 Timer Low 1 Timer Low 2 C9H 8CH 8DH CDH 8AH 8BH CCH - - - - - - T2OE DCEN M1 M0 GATE C/T M1 M0 TMOD Timer Mode 89H GATE C/T * SFRs are bit addressable. # SFRs are modified from or added to the 80C51 SFRs. - Reserved bits. 1. Reset value depends on reset source. 2. Bit will not be affected by Reset. POF is not present in 80C52. 1996 Aug 16 00H 5 00H 00H xxxxxx00B 00H 00H 00H 00H 00H 00H 00H Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers PLASTIC LEADED CHIP CARRIER PIN FUNCTIONS 6 1 80C52/80C54/80C58 PLASTIC QUAD FLAT PACK PIN FUNCTIONS 44 40 7 39 1 33 LCC PQFP 17 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Function NC* P1.0/T2 P1.1/T2EX P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 RST P3.0/RxD NC* P3.1/TxD P3.2/INT0 P3.3/INT1 11 29 18 Pin 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 34 28 23 12 Pin 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Function P3.4/T0 P3.5/T1 P3.6/WR P3.7/RD XTAL2 XTAL1 VSS NC* P2.0/A8 P2.1/A9 P2.2/A10 P2.3/A11 P2.4/A12 P2.5/A13 P2.6/A14 * DO NOT CONNECT Function P2.7/A15 PSEN ALE NC* EA P0.7/AD7 P0.6/AD6 P0.5/AD5 P0.4/AD4 P0.3/AD3 P0.2/AD2 P0.1/AD1 P0.0/AD0 VCC Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Function P1.5 P1.6 P1.7 RST P3.0/RxD NC* P3.1/TxD P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1 P3.6/WR P3.7/RD XTAL2 XTAL1 Pin 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 22 Function VSS NC* P2.0/A8 P2.1/A9 P2.2/A10 P2.3/A11 P2.4/A12 P2.5/A13 P2.6/A14 P2.7/A15 PSEN ALE NC* EA P0.7/AD7 Pin 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Function P0.6/AD6 P0.5/AD5 P0.4/AD4 P0.3/AD3 P0.2/AD2 P0.1/AD1 P0.0/AD0 VCC NC* P1.0/T2 P1.1/T2EX P1.2 P1.3 P1.4 * DO NOT CONNECT SU00741A SU00742A PIN DESCRIPTIONS PIN NUMBER MNEMONIC DIP LCC QFP TYPE VSS 20 22 16 I Ground: 0V reference. VCC 40 44 38 I Power Supply: This is the power supply voltage for normal, idle, and power-down operation. 39-32 43-36 37-30 I/O Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to them float and can be used as high-impedance inputs. Port 0 is also the multiplexed low-order address and data bus during accesses to external program and data memory. In this application, it uses strong internal pull-ups when emitting 1s. Port 0 also outputs the code bytes during program verification. External pull-ups are required during program verification. 1-8 2-9 40-44, 1-3 I/O 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 9 40 41 42 43 44 1 2 3 I/O I I I/O I/O I/O I/O I/O Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 1 pins that are externally pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: IIL). Port 1 also receives the low-order address byte during program memory verification. Alternate functions include: T2 (P1.0): Timer/Counter 2 external count input/Clockout T2EX (P1.1): Timer/Counter 2 Reload/Capture/Direction Control 21-28 24-31 18-25 I/O P0.0-0.7 P1.0-P1.7 P2.0-P2.7 1996 Aug 16 NAME AND FUNCTION Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 2 pins that are externally being pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: IIL). Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX @DPTR). In this application, it uses strong internal pull-ups when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOV @Ri), port 2 emits the contents of the P2 special function register. 6 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 PIN DESCRIPTIONS (Continued) PIN NUMBER MNEMONIC DIP LCC QFP TYPE 10-17 11, 13-19 5, 7-13 I/O 10 11 12 13 14 15 16 17 11 13 14 15 16 17 18 19 5 7 8 9 10 11 12 13 I O I I I I O O RST 9 10 4 I Reset: A high on this pin for two machine cycles while the oscillator is running, resets the device. An internal diffused resistor to VSS permits a power-on reset using only an external capacitor to VCC. ALE 30 33 27 O Address Latch Enable: Output pulse for latching the low byte of the address during an access to external memory. In normal operation, ALE is emitted at a constant rate of 1/6 the oscillator frequency, and can be used for external timing or clocking. Note that one ALE pulse is skipped during each access to external data memory. ALE can be disabled by setting SFR auxiliary.0. With this bit set, ALE will be active only during a MOVX instruction. PSEN 29 32 26 O Program Store Enable: The read strobe to external program memory. When the 80C52/80C54/80C58 is executing code from the external program memory, PSEN is activated twice each machine cycle, except that two PSEN activations are skipped during each access to external data memory. PSEN is not activated during fetches from internal program memory. EA 31 35 29 I External Access Enable: EA must be externally held low to enable the device to fetch code from external program memory locations 0000H and 7FFFH. If EA is held high, the device executes from internal program memory unless the program counter contains an address greater than 7FFFH. If security bit 1 is programmed, EA will be internally latched on Reset. XTAL1 19 21 15 I Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator circuits. XTAL2 18 20 14 O Crystal 2: Output from the inverting oscillator amplifier. P3.0-P3.7 NAME AND FUNCTION Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 3 pins that are externally being pulled low will source current because of the pull-ups. (See DC Electrical Characteristics: IIL). Port 3 also serves the special features of the 80C51 family, as listed below: RxD (P3.0): Serial input port TxD (P3.1): Serial output port INT0 (P3.2): External interrupt INT1 (P3.3): External interrupt T0 (P3.4): Timer 0 external input T1 (P3.5): Timer 1 external input WR (P3.6): External data memory write strobe RD (P3.7): External data memory read strobe NOTE: To avoid "latch-up" effect at power-on, the voltage on any pin at any time must not be higher than VCC + 0.5V or VSS - 0.5V, respectively. 1996 Aug 16 7 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 Figure 3). When reset is applied the DCEN=0 which means Timer 2 will default to counting up. If DCEN bit is set, Timer 2 can count up or down depending on the value of the T2EX pin. TIMER 2 OPERATION Timer 2 Timer 2 is a 16-bit Timer/Counter which can operate as either an event timer or an event counter, as selected by C/T2* in the special function register T2CON (see Figure 1). Timer 2 has three operating modes:Capture, Auto-reload (up or down counting) ,and Baud Rate Generator, which are selected by bits in the T2CON as shown in Table 2. Figure 4 shows Timer 2 which will count up automatically since DCEN=0. In this mode there are two options selected by bit EXEN2 in T2CON register. If EXEN2=0, then Timer 2 counts up to 0FFFFH and sets the TF2 (Overflow Flag) bit upon overflow. This causes the Timer 2 registers to be reloaded with the 16-bit value in RCAP2L and RCAP2H. Capture Mode The values in RCAP2L and RCAP2H are preset by software means. If EXEN2=1, then a 16-bit reload can be triggered either by an overflow or by a 1-to-0 transition at input T2EX. This transition also sets the EXF2 bit. The Timer 2 interrupt, if enabled, can be generated when either TF2 or EXF2 are 1. In the capture mode there are two options which are selected by bit EXEN2 in T2CON. If EXEN2=0, then timer 2 is a 16-bit timer or counter (as selected by C/T2* in T2CON) which, upon overflowing sets bit TF2, the timer 2 overflow bit. This bit can be used to generate an interrupt (by enabling the Timer 2 interrupt bit in the IE register/SFR table). If EXEN2= 1, Timer 2 operates as described above, but with the added feature that a 1- to -0 transition at external input T2EX causes the current value in the Timer 2 registers, TL2 and TH2, to be captured into registers RCAP2L and RCAP2H, respectively. In addition, the transition at T2EX causes bit EXF2 in T2CON to be set, and EXF2 like TF2 can generate an interrupt (which vectors to the same location as Timer 2 overflow interrupt. The Timer 2 interrupt service routine can interrogate TF2 and EXF2 to determine which event caused the interrupt). The capture mode is illustrated in Figure 2 (There is no reload value for TL2 and TH2 in this mode. Even when a capture event occurs from T2EX, the counter keeps on counting T2EX pin transitions or osc/12 pulses.). In Figure 5 DCEN=1 which enables Timer 2 to count up or down. This mode allows pin T2EX to control the direction of count. When a logic 1 is applied at pin T2EX Timer 2 will count up. Timer 2 will overflow at 0FFFFH and set the TF2 flag, which can then generate an interrupt, if the interrupt is enabled. This timer overflow also causes the 16-bit value in RCAP2L and RCAP2H to be reloaded into the timer registers TL2 and TH2. When a logic 0 is applied at pin T2EX this causes Timer 2 to count down. The timer will underflow when TL2 and TH2 become equal to the value stored in RCAP2L and RCAP2H. Timer 2 underflow sets the TF2 flag and causes 0FFFFH to be reloaded into the timer registers TL2 and TH2. Auto-Reload Mode (Up or Down Counter) The external flag EXF2 toggles when Timer 2 underflows or overflows. This EXF2 bit can be used as a 17th bit of resolution if needed. The EXF2 flag does not generate an interrupt in this mode of operation. In the 16-bit auto-reload mode, Timer 2 can be configured (as either a timer or counter (C/T2* in T2CON)) then programmed to count up or down. The counting direction is determined by bit DCEN(Down Counter Enable) which is located in the T2MOD register (see (MSB) TF2 (LSB) EXF2 RCLK TCLK EXEN2 TR2 C/T2 CP/RL2 Symbol Position Name and Significance TF2 T2CON.7 EXF2 T2CON.6 RCLK T2CON.5 TCLK T2CON.4 EXEN2 T2CON.3 TR2 C/T2 T2CON.2 T2CON.1 CP/RL2 T2CON.0 Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set when either RCLK or TCLK = 1. Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and EXEN2 = 1. When Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2 interrupt routine. EXF2 must be cleared by software. EXF2 does not cause an interrupt in up/down counter mode (DCEN = 1). Receive clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its receive clock in modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for the receive clock. Transmit clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock in modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock. Timer 2 external enable flag. When set, allows a capture or reload to occur as a result of a negative transition on T2EX if Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to ignore events at T2EX. Start/stop control for Timer 2. A logic 1 starts the timer. Timer or counter select. (Timer 2) 0 = Internal timer (OSC/12) 1 = External event counter (falling edge triggered). Capture/Reload flag. When set, captures will occur on negative transitions at T2EX if EXEN2 = 1. When cleared, auto-reloads will occur either with Timer 2 overflows or negative transitions at T2EX when EXEN2 = 1. When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is forced to auto-reload on Timer 2 overflow. SU00728 Figure 1. Timer/Counter 2 (T2CON) Control Register 1996 Aug 16 8 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 Table 2. Timer 2 Operating Modes RCLK + TCLK CP/RL2 TR2 0 0 1 16-bit Auto-reload 0 1 1 16-bit Capture 1 X 1 Baud rate generator X X 0 (off) OSC MODE / 12 C/T2 = 0 TL2 (8-bits) TH2 (8-bits) TF2 C/T2 = 1 T2 Pin Control TR2 Capture Transition Detector Timer 2 Interrupt RCAP2L RCAP2H T2EX Pin EXF2 Control EXEN2 SU00066 Figure 2. Timer 2 in Capture Mode T2MOD Address = 0C9H Reset Value = XXXX XX00B Not Bit Addressable Bit * -- -- -- -- -- -- T2OE DCEN 7 6 5 4 3 2 1 0 Symbol Function -- Not implemented, reserved for future use.* T2OE Timer 2 Output Enable bit. See details in Programmable Clock-Out. DCEN Down Count Enable bit. When set, this allows Timer 2 to be configured as an up/down counter. User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features. In that case, the reset or inactive value of the new bit will be 0, and its active value will be 1. The value read from a reserved bit is indeterminate. SU00746 Figure 3. Timer 2 Mode (T2MOD) Control Register 1996 Aug 16 9 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 / 12 OSC C/T2 = 0 TL2 (8-BITS) TH2 (8-BITS) C/T2 = 1 T2 PIN CONTROL TR2 RELOAD TRANSITION DETECTOR RCAP2L RCAP2H TF2 TIMER 2 INTERRUPT T2EX PIN EXF2 CONTROL EXEN2 SU00067 Figure 4. Timer 2 in Auto-Reload Mode (DCEN = 0) (DOWN COUNTING RELOAD VALUE) FFH FFH TOGGLE EXF2 OSC /12 C/T2 = 0 OVERFLOW TL2 T2 PIN TH2 TF2 INTERRUPT C/T2 = 1 CONTROL TR2 COUNT DIRECTION 1 = UP 0 = DOWN RCAP2L RCAP2H (UP COUNTING RELOAD VALUE) Figure 5. Timer 2 Auto Reload Mode (DCEN = 1) 1996 Aug 16 10 T2EX PIN SU00730 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 Timer 1 Overflow /2 NOTE: OSC. Freq. is divided by 2, not 12. "0" /2 OSC "1" C/T2 = 0 SMOD TL2 (8-bits) "1" TH2 (8-bits) "0" RCLK C/T2 = 1 T2 Pin Control / 16 "1" TR2 Reload Transition Detector RCAP2L T2EX Pin EXF2 RCAP2H RX Clock "0" TCLK / 16 TX Clock Timer 2 Interrupt Control EXEN2 Note availability of additional external interrupt. SU00068 Figure 6. Timer 2 in Baud Rate Generator Mode Table 3. The baud rates in modes 1 and 3 are determined by Timer 2's overflow rate given below: Timer 2 Generated Commonly Used Baud Rates Modes 1 and 3 Baud Rates Timer 2 Overflow Rate 16 Timer 2 Baud Rate Osc Freq 375K 9.6K 2.8K 2.4K 1.2K 300 110 300 110 12MHz 12MHz 12MHz 12MHz 12MHz 12MHz 12MHz 6MHz 6MHz RCAP2H RCAP2L FF FF FF FF FE FB F2 FD F9 FF D9 B2 64 C8 1E AF 8F 57 The timer can be configured for either "timer" or "counter" operation. In many applications, it is configured for "timer" operation (C/T2*=0). Timer operation is different for Timer 2 when it is being used as a baud rate generator. Usually, as a timer it would increment every machine cycle (i.e., 1/12 the oscillator frequency). As a baud rate generator, it increments every state time (i.e., 1/2 the oscillator frequency). Thus the baud rate formula is as follows: Modes 1 and 3 Baud Rates = Oscillator Frequency [32 [65536 (RCAP2H, RCAP2L)]] Baud Rate Generator Mode Where: (RCAP2H, RCAP2L)= The content of RCAP2H and RCAP2L taken as a 16-bit unsigned integer. Bits TCLK and/or RCLK in T2CON (Table 2) allow the serial port transmit and receive baud rates to be derived from either Timer 1 or Timer 2. When TCLK= 0, Timer 1 is used as the serial port transmit baud rate generator. When TCLK= 1, Timer 2 is used as the serial port transmit baud rate generator. RCLK has the same effect for the serial port receive baud rate. With these two bits, the serial port can have different receive and transmit baud rates - one generated by Timer 1, the other by Timer 2. The Timer 2 as a baud rate generator mode shown in Figure 6, is valid only if RCLK and/or TCLK = 1 in T2CON register. Note that a rollover in TH2 does not set TF2, and will not generate an interrupt. Thus, the Timer 2 interrupt does not have to be disabled when Timer 2 is in the baud rate generator mode. Also if the EXEN2 (T2 external enable flag) is set, a 1-to-0 transition in T2EX (Timer/counter 2 trigger input) will set EXF2 (T2 external flag) but will not cause a reload from (RCAP2H, RCAP2L) to (TH2,TL2). Therefore when Timer 2 is in use as a baud rate generator, T2EX can be used as an additional external interrupt, if needed. Figure 6 shows the Timer 2 in baud rate generation mode. The baud rate generation mode is like the auto-reload mode,in that a rollover in TH2 causes the Timer 2 registers to be reloaded with the 16-bit value in registers RCAP2H and RCAP2L, which are preset by software. 1996 Aug 16 11 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers To obtain the reload value for RCAP2H and RCAP2L, the above equation can be rewritten as: When Timer 2 is in the baud rate generator mode, one should not try to read or write TH2 and TL2. As a baud rate generator, Timer 2 is incremented every state time (osc/2) or asynchronously from pin T2; under these conditions, a read or write of TH2 or TL2 may not be accurate. The RCAP2 registers may be read, but should not be written to, because a write might overlap a reload and cause write and/or reload errors. The timer should be turned off (clear TR2) before accessing the Timer 2 or RCAP2 registers. RCAP2H, RCAP2L + 65536 * 32 f OSC Baud Rate Except for the baud rate generator mode, the values given for T2CON do not include the setting of the TR2 bit. Therefore, bit TR2 must be set, separately, to turn the timer on. see Table 4 for set-up of Timer 2 as a timer. Also see Table 5 for set-up of Timer 2 as a counter. Summary Of Baud Rate Equations Timer 2 is in baud rate generating mode. If Timer 2 is being clocked through pin T2(P1.0) the baud rate is: POWER OFF FLAG3 Baud Rate + Timer 2 Overflow Rate 16 The Power Off Flag (POF) is set by on-chip circuitry when the VCC level on the 80C54/80C58 rises from 0 to 5V. The POF bit can be set or cleared by software allowing a user to determine if the reset is the result of a power-on or a warm start after powerdown. The VCC level must remain above 3V for the POF to remain unaffected by the VCC level. If Timer 2 is being clocked internally, the baud rate is: [32 Timer/Counter 2 Set-up Table 3 shows commonly used baud rates and how they can be obtained from Timer 2. Baud Rate + 80C52/80C54/80C58 f OSC [65536 * (RCAP2H, RCAP2L)]] Where fOSC= Oscillator Frequency Table 4. Timer 2 as a Timer T2CON MODE INTERNAL CONTROL (Note 1) EXTERNAL CONTROL (Note 2) 16-bit Auto-Reload 00H 08H 16-bit Capture 01H 09H Baud rate generator receive and transmit same baud rate 34H 36H Receive only 24H 26H Transmit only 14H 16H Table 5. Timer 2 as a Counter TMOD MODE INTERNAL CONTROL (Note 1) EXTERNAL CONTROL (Note 2) 16-bit 02H 0AH Auto-Reload 03H 0BH NOTES: 1. Capture/reload occurs only on timer/counter overflow. 2. Capture/reload occurs on timer/counter overflow and a 1-to-0 transition on T2EX (P1.1) pin except when Timer 2 is used in the baud rate generator mode. 3. POF not present in 80C52. 1996 Aug 16 12 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 oscillator but bringing the pin back high completes the exit. Once the interrupt is serviced, the next instruction to be executed after RETI will be the one following the instruction that put the device into Power Down. OSCILLATOR CHARACTERISTICS XTAL1 and XTAL2 are the input and output, respectively, of an inverting amplifier. The pins can be configured for use as an on-chip oscillator. Design Consideration To drive the device from an external clock source, XTAL1 should be driven while XTAL2 is left unconnected. There are no requirements on the duty cycle of the external clock signal, because the input to the internal clock circuitry is through a divide-by-two flip-flop. However, minimum and maximum high and low times specified in the data sheet must be observed. * When the idle mode is terminated by a hardware reset, the device normally resumes program execution, from where it left off, up to two machine cycles before the internal rest algorithm takes control. On-chip hardware inhibits access to internal RAM in this event, but access to the port pins is not inhibited. To eliminate the possibility of an unexpected write when Idle is terminated by reset, the instruction following the one that invokes Idle should not be one that writes to a port pin or to external memory. Reset A reset is accomplished by holding the RST pin high for at least two machine cycles (24 oscillator periods), while the oscillator is running. To insure a good power-on reset, the RST pin must be high long enough to allow the oscillator time to start up (normally a few milliseconds) plus two machine cycles. At power-on, the voltage on VCC and RST must come up at the same time for a proper start-up. Ports 1, 2, and 3 will asynchronously be driven to their reset condition when a voltage above VIH1 (min.) is applied to RESET. ONCE Mode The ONCE ("On-Circuit Emulation") Mode facilitates testing and debugging of systems using the 80C52/54/58 without removing the device from the circuit. The ONCE Mode is invoked by: 1. Pull ALE low while the device is in reset and PSEN is high; 2. Hold ALE low as RST is deactivated. Idle Mode While the device is in ONCE Mode, the Port 0 pins go into a float state, and the other port pins and ALE and PSEN are weakly pulled high. The oscillator circuit remains active. While the 80C52/54/58 is in this mode, an emulator or test CPU can be used to drive the circuit. Normal operation is restored when a normal reset is applied. In the idle mode (see Table 6), the CPU puts itself to sleep while all of the on-chip peripherals stay active. The instruction to invoke the idle mode is the last instruction executed in the normal operating mode before the idle mode is activated. The CPU contents, the on-chip RAM, and all of the special function registers remain intact during this mode. The idle mode can be terminated either by any enabled interrupt (at which time the process is picked up at the interrupt service routine and continued), or by a hardware reset which starts the processor in the same manner as a power-on reset. Programmable Clock-Out The 80C52/54/58 has a new feature. A 50% duty cycle clock can be programmed to come out on P1.0. This pin, besides being a regular I/O pin, has two alternate functions. It can be programmed: 1. to input the external clock for Timer/Counter 2, or 2. to output a 50% duty cycle clock ranging from 61Hz to 4MHz at a 16MHz operating frequency. Power-Down Mode To save even more power, a Power Down mode (see Table 6) can be invoked by software. In this mode, the oscillator is stopped and the instruction that invoked Power Down is the last instruction executed. The on-chip RAM and Special Function Registers retain their values until the Power Down mode is terminated. To configure the Timer/Counter 2 as a clock generator, bit C/T2 (in T2CON) must be cleared and bit T2OE in T2MOD must be set. Bit TR2 (T2CON.2) also must be set to start the timer. The Clock-Out frequency depends on the oscillator frequency and the reload value of Timer 2 capture registers (RCAP2H, RCAP2L) as shown in this equation: On the 80C52/54/58 either a hardware reset or external interrupt can be used to exit from Power Down. Reset redefines all the SFRs but does not change the on-chip RAM. An external interrupt allows both the SFRs and the on-chip RAM to retain their values. Oscillator Frequency 4 (65536 RCAP2H, RCAP2L) To properly terminate Power Down the reset or external interrupt should not be executed before VCC is restored to its normal operating level and must be held active long enough for the oscillator to restart and stabilize (normally less than 10ms). In the Clock-Out mode Timer 2 roll-overs will not generate an interrupt. This is similar to when it is used as a baud-rate generator. It is possible to use Timer 2 as a baud-rate generator and a clock generator simultaneously. Note, however, that the baud-rate and the Clock-Out frequency will be the same. With an external interrupt, INT0 and INT1 must be enabled and configured as level-sensitive. Holding the pin low restarts the Table 6. External Pin Status During Idle and Power-Down Mode PROGRAM MEMORY ALE PSEN PORT 0 PORT 1 PORT 2 PORT 3 Idle Internal 1 1 Data Data Data Data Idle External 1 1 Float Data Address Data Power-down Internal 0 0 Data Data Data Data Power-down External 0 0 Float Data Data Data MODE 1996 Aug 16 13 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers Slave 1 Enhanced UART The UART operates in all of the usual modes that are described in the first section of Data Handbook IC20, 80C51-Based 8-Bit Microcontrollers. In addition the UART can perform framing error detect by looking for missing stop bits, and automatic address recognition. The 80C52/54/58 UART also fully supports multiprocessor communication as does the standard 80C51 UART. Slave 0 SADDR = SADEN = Given = 1100 0000 1111 1001 1100 0XX0 Slave 1 SADDR = SADEN = Given = 1110 0000 1111 1010 1110 0X0X Slave 2 SADDR = SADEN = Given = 1110 0000 1111 1100 1110 00XX In the above example the differentiation among the 3 slaves is in the lower 3 address bits. Slave 0 requires that bit 0 = 0 and it can be uniquely addressed by 1110 0110. Slave 1 requires that bit 1 = 0 and it can be uniquely addressed by 1110 and 0101. Slave 2 requires that bit 2 = 0 and its unique address is 1110 0011. To select Slaves 0 and 1 and exclude Slave 2 use address 1110 0100, since it is necessary t make bit 2 = 1 to exclude slave 2. The 8 bit mode is called Mode 1. In this mode the RI flag will be set if SM2 is enabled and the information received has a valid stop bit following the 8 address bits and the information is either a Given or Broadcast address. Mode 0 is the Shift Register mode and SM2 is ignored. The Broadcast Address for each slave is created by taking the logical OR of SADDR and SADEN. Zeros in this result are teated as don't-cares. In most cases, interpreting the don't-cares as ones, the broadcast address will be FF hexadecimal. Using the Automatic Address Recognition feature allows a master to selectively communicate with one or more slaves by invoking the Given slave address or addresses. All of the slaves may be contacted by using the Broadcast address. Two special Function Registers are used to define the slave's address, SADDR, and the address mask, SADEN. SADEN is used to define which bits in the SADDR are to b used and which bits are "don't care". The SADEN mask can be logically ANDed with the SADDR to create the "|Given" address which the master will use for addressing each of the slaves. Use of the Given address allows multiple slaves to be recognized while excluding others. The following examples will help to show the versatility of this scheme: 1996 Aug 16 1100 0000 1111 1110 1100 000X In a more complex system the following could be used to select slaves 1 and 2 while excluding slave 0: Automatic Address Recognition Automatic Address Recognition is a feature which allows the UART to recognize certain addresses in the serial bit stream by using hardware to make the comparisons. This feature saves a great deal of software overhead by eliminating the need for the software to examine every serial address which passes by the serial port. This feature is enabled by setting the SM2 bit in SCON. In the 9 bit UART modes, mode 2 and mode 3, the Receive Interrupt flag (RI) will be automatically set when the received byte contains either the "Given" address or the "Broadcast" address. The 9 bit mode requires that the 9th information bit is a 1 to indicate that the received information is an address and not data. Automatic address recognition is shown in Figure 9. SADDR = SADEN = Given = SADDR = SADEN = Given = In the above example SADDR is the same and the SADEN data is used to differentiate between the two slaves. Slave 0 requires a 0 in bit 0 and it ignores bit 1. Slave 1 requires a 0 in bit 1 and bit 0 is ignored. A unique address for Slave 0 would be 1100 0010 since slave 1 requires a 0 in bit 1. A unique address for slave 1 would be 1100 0001 since a 1 in bit 0 will exclude slave 0. Both slaves can be selected at the same time by an address which has bit 0 = 0 (for slave 0) and bit 1 = 0 (for slave 1). Thus, both could be addressed with 1100 0000. When used for framing error detect the UART looks for missing stop bits in the communication. A missing bit will set the FE bit in the SCON register. The FE bit shares the SCON.7 bit with SM0 and the function of SCON.7 is determined by PCON.6 (SMOD0) (see Figure 7). If SMOD0 is set then SCON.7 functions as FE. SCON.7 functions as SM0 when SMOD0 is cleared. When used as FE SCON.7 can only be cleared by software. Refer to Figure 8. Slave 0 80C52/80C54/80C58 Upon reset SADDR (SFR address 0A9H) and SADEN (SFR address 0B9H) are leaded with 0s. This produces a given address of all "don't cares" as well as a Broadcast address of all "don't cares". this effectively disables the Automatic Addressing mode and allows the microcontroller to use standard 80C51 type UART drivers which do not make use of this feature. 1100 0000 1111 1101 1100 00X0 14 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 SCON Address = 98H Reset Value = 0000 0000B Bit Addressable SM0/FE Bit: SM1 SM2 REN TB8 RB8 Tl Rl 5 4 3 2 1 0 7 6 (SMOD0 = 0/1)* Symbol Function FE Framing Error bit. This bit is set by the receiver when an invalid stop bit is detected. The FE bit is not cleared by valid frames but should be cleared by software. The SMOD0 bit must be set to enable access to the FE bit. SM0 Serial Port Mode Bit 0, (SMOD0 must = 0 to access bit SM0) SM1 Serial Port Mode Bit 1 SM0 SM1 Mode 0 0 1 1 0 1 0 1 0 1 2 3 Description Baud Rate** shift register 8-bit UART 9-bit UART 9-bit UART fOSC/12 variable fOSC/64 or fOSC/32 variable SM2 Enables the Automatic Address Recognition feature in Modes 2 or 3. If SM2 = 1 then Rl will not be set unless the received 9th data bit (RB8) is 1, indicating an address, and the received byte is a Given or Broadcast Address. In Mode 1, if SM2 = 1 then Rl will not be activated unless a valid stop bit was received, and the received byte is a Given or Broadcast Address. In Mode 0, SM2 should be 0. REN Enables serial reception. Set by software to enable reception. Clear by software to disable reception. TB8 The 9th data bit that will be transmitted in Modes 2 and 3. Set or clear by software as desired. RB8 In modes 2 and 3, the 9th data bit that was received. In Mode 1, if SM2 = 0, RB8 is the stop bit that was received. In Mode 0, RB8 is not used. Tl Transmit interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or at the beginning of the stop bit in the other modes, in any serial transmission. Must be cleared by software. Rl Receive interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or halfway through the stop bit time in the other modes, in any serial reception (except see SM2). Must be cleared by software. NOTE: *SMOD0 is located at PCON6. **fOSC = oscillator frequency SU00043 Figure 7. SCON: Serial Port Control Register D0 D1 D2 START BIT D3 D4 D5 D6 D7 D8 DATA BYTE ONLY IN MODE 2, 3 STOP BIT SET FE BIT IF STOP BIT IS 0 (FRAMING ERROR) SM0 TO UART MODE CONTROL SM0 / FE SM1 SM2 REN TB8 RB8 TI RI SCON (98H) SMOD1 SMOD0 - POF GF1 GF0 PD IDL PCON (87H) 0 : SCON.7 = SM0 1 : SCON.7 = FE SU00747 Figure 8. UART Framing Error Detection 1996 Aug 16 15 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers D0 D1 D2 D3 80C52/80C54/80C58 D4 SM0 SM1 1 1 1 0 D5 SM2 D6 D7 D8 REN TB8 RB8 1 X 1 TI SCON (98H) RI RECEIVED ADDRESS D0 TO D7 COMPARATOR PROGRAMMED ADDRESS IN UART MODE 2 OR MODE 3 AND SM2 = 1: INTERRUPT IF REN=1, RB8=1 AND "RECEIVED ADDRESS" = "PROGRAMMED ADDRESS" - WHEN OWN ADDRESS RECEIVED, CLEAR SM2 TO RECEIVE DATA BYTES - WHEN ALL DATA BYTES HAVE BEEN RECEIVED: SET SM2 TO WAIT FOR NEXT ADDRESS. SU00045 Figure 9. UART Multiprocessor Communication, Automatic Address Recognition Interrupt Priority Structure PRIORITY BITS The 80C52/54/58 has a 6-source four-level interrupt structure. There are 3 SFRs associated with the interrupts on the 80C52/54/58. They are the IE and IP. (See Figures 10 and 11.) In addition, there is the IPH (Interrupt Priority High) register that makes the four-level interrupt structure possible. The IPH is located at SFR address B7H. The structure of the IPH register and a description of its bits is shown below: IPH (Interrupt Priority High) (B7H) 7 6 - IPH.0 IPH.1 IPH.2 IPH.3 IPH.4 IPH.5 IPH.6 IPH.7 - PX0H PT0H PX1H PT1H PSH PT2H -- -- 5 4 3 2 1 0 PT2H PSH PT1H PX1H PT0H PX0H INTERRUPT PRIORITY LEVEL IPH.x IP.x 0 0 Level 0 (lowest priority) 0 1 Level 1 1 0 Level 2 1 1 Level 3 (highest priority) The priority scheme for servicing the interrupts is the same as that for the 80C51, except there are four interrupt levels on the 80C52/54/58 rather than two as on the 80C51. An interrupt will be serviced as long as an interrupt of equal or higher priority is not already being serviced. If an interrupt of equal or higher level priority is being serviced, the new interrupt will wait until it is finished before being serviced. If a lower priority level interrupt is being serviced, it will be stopped and the new interrupt serviced. When the new interrupt is finished, the lower priority level interrupt that was stopped will be completed. External interrupt 0 priority high Timer 0 interrupt priority high External interrupt 1 priority high Timer 1 interrupt priority high Serial Port interrupt high Timer 2 interrupt priority high Not implemented Not implemented The function of the IPH SFR is simple and when combined with the IP SFR determines the priority of each interrupt. The priority of each interrupt is determined as shown in the following table: Table 7. Interrupt Table SOURCE POLLING PRIORITY REQUEST BITS X0 1 IE0 HARDWARE CLEAR? T0 2 TP0 Y 0BH X1 3 IE1 N (L) Y (T) 13H 1BH N (L)1 Y (T)2 VECTOR ADDRESS 03H T1 4 TF1 Y SP 5 R1, TI N 23H T2 6 TF2, EXF2 N 2BH PCA 7 CF, CCFn n = 0-4 N 33H NOTES: 1. L = Level activated 2. T = Transition activated 1996 Aug 16 16 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers IE0 (A8H) 80C52/80C54/80C58 7 6 5 4 3 2 1 0 EA -- ET2 ES ET1 EX1 ET0 EX0 Enable Bit = 1 enables the interrupt. Enable Bit = 0 disables it. BIT IE.7 SYMBOL EA IE.6 IE.5 IE.4 IE.3 IE.2 IE.1 IE.0 -- ET2 ES ET1 EX1 ET0 EX0 FUNCTION Global disable bit. If EA = 0, all interrupts are disabled. If EA = 1, each interrupt can be individually enabled or disabled by setting or clearing its enable bit. Timer 2 interrupt enable bit. Serial Port interrupt enable bit. Timer 1 interrupt enable bit. External interrupt 1 enable bit. Timer 0 interrupt enable bit. External interrupt 0 enable bit. SU00743 Figure 10. IE Registers IP0 (B8H) 7 6 5 4 3 2 1 0 -- -- PT2 PS PT1 PX1 PT0 PX0 Priority Bit = 1 assigns high priority Priority Bit = 0 assigns low priority BIT IP.7 IP.6 IP.5 IP.4 IP.3 IP.2 IP.1 IP.0 SYMBOL -- -- PT2 PS PT1 PX1 PT0 PX0 FUNCTION Not implemented, reserved for future use. Timer 2 interrupt priority bit. Serial Port interrupt priority bit. Timer 1 interrupt priority bit. External interrupt 1 priority bit. Timer 0 interrupt priority bit. External interrupt 0 priority bit. SU00744 Figure 11. IP Registers 1996 Aug 16 17 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 Reduced EMI Mode The AO bit (AUXR.0) in the AUXR register when set disables the ALE output. DPS BIT0 AUXR1 80C52/80C54/80C58 Reduced EMI Mode DPTR1 DPTR0 AUXR (8EH) 7 6 5 4 3 2 1 0 - - - - - - - AO AO: DPH (83H) DPL (82H) EXTERNAL DATA MEMORY Turns off ALE output. SU00745A Figure 12. DPTR Structure Dual Data Pointer Register (DPTR) The dual DPTR structure (see Figure 12) is a way by which the 80C52/54/58 will specify the address of an external data memory location. There are two 16-bit DPTR registers that address the external memory, and a single bit called DPS = AUXR1/bit0 that allows the program code to switch between them. DPTR Instructions The instructions that refer to DPTR refer to the data pointer that is currently selected using the AUXR1/bit 0 register. The six instructions that use the DPTR are as follows: * Register Name: AUXR1# * SFR Address: A2H * Reset Value: xxxxxxx0B 7 6 5 4 3 2 1 0 - - - - - - - DPS Where: DPS = AUXR1/bit0 = Switches between DPTR0 and DPTR1. Select Reg DPS DPTR0 0 DPTR1 1 INC DPTR Increments the data pointer by 1 MOV DPTR, #data16 Loads the DPTR with a 16-bit constant MOV A, @ A+DPTR Move code byte relative to DPTR to ACC MOVX A, @ DPTR Move external RAM (16-bit address) to ACC MOVX @ DPTR , A Move ACC to external RAM (16-bit address) JMP @ A + DPTR Jump indirect relative to DPTR The data pointer can be accessed on a byte-by-byte basis by specifying the Low or High byte in an instruction which accesses the SFRs. See application note AN458 for detailed operation The DPS bit status whould be saved by software when switching between DPTR0 and DPTR1. ABSOLUTE MAXIMUM RATINGS1, 2, 3 PARAMETER Operating temperature under bias Storage temperature range Voltage on EA/VPP pin to VSS Voltage on any other pin to VSS RATING UNIT 0 to +70 or -40 to +85 C -65 to +150 C 0 to +13.0 V -0.5 to +6.5 V Maximum IOL per I/O pin 15 mA Power dissipation (based on package heat transfer limitations, not device power consumption) 1.5 W NOTES: 1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any conditions other than those described in the AC and DC Electrical Characteristics section of this specification is not implied. 2. This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maxima. 3. Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless otherwise noted. 1996 Aug 16 18 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 DC ELECTRICAL CHARACTERISTICS Tamb = 0C to +70C or -40C to +85C, VCC = 5.0V 10%; VSS = 0V SYMBOL TEST CONDITIONS PARAMETER VIL Input low voltage VIH Input high voltage (ports 0, 1, 2, 3, EA) VIH1 Input high voltage, XTAL1, RST VOL Output low voltage, ports 1, 2, 38 VOL1 MIN TYP1 UNIT MAX -0.5 0.2VCC-0.1 V 0.2VCC+0.9 VCC+0.5 V 0.7VCC VCC+0.5 V VCC = 4.5V IOL = 1.6mA2 0.4 V Output low voltage, port 0, ALE, PSEN8, 7 VCC = 4.5V IOL = 3.2mA2 0.4 V VOH Output high voltage, ports 1, 2, 3 3 VCC = 4.5V IOH = -30A VCC - 0.7 V VOH1 Output high voltage (port 0 in external bus mode), ALE9, PSEN3 VCC = 4.5V IOH = -3.2mA VCC - 0.7 V IIL Logical 0 input current, ports 1, 2, 3 VIN = 0.4V -1 ITL Logical 1-to-0 transition current, ports 1, 2, 36 ILI Input leakage current, port 0 ICC Power supply current (see Figure 20): Active mode @ 16MHz5 Idle mode @ 16MHz5 Power-down mode RRST Internal reset pull-down resistor CIO Pin capacitance10 (except EA) 4.5V < VCC < 5.5V LIMITS -50 A VIN = 2.0V See note 4 -650 A 0.45 < VIN < VCC - 0.3 10 A 16 4 50 75 mA mA A A 225 k 15 pF See note 5 Tamb = 0 to +70C Tamb = -40 to +85C 3 40 NOTES: 1. Typical ratings are not guaranteed. The values listed are at room temperature, 5V. 2. Capacitive loading on ports 0 and 2 may cause spurious noise to be superimposed on the VOLs of ALE and ports 1 and 3. The noise is due to external bus capacitance discharging into the port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operations. In the worst cases (capacitive loading > 100pF), the noise pulse on the ALE pin may exceed 0.8V. In such cases, it may be desirable to qualify ALE with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input. IOL can exceed these conditions provided that no single output sinks more than 5mA and no more than two outputs exceed the test conditions. 3. Capacitive loading on ports 0 and 2 may cause the VOH on ALE and PSEN to momentarily fall below the (VCC-0.7) specification when the address bits are stabilizing. 4. Pins of ports 1, 2 and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its maximum value when VIN is approximately 2V. 5. See Figures 21 through 24 for ICC test conditions. Active Mode: ICC = 0.9 x FREQ + 1.1; Idle Mode: ICC = 0.18 x FREQ +1.0; See Figure 20. 6. This value applies to Tamb = 0C to +70C. For Tamb = -40C to +85C, ITL = -750A. 7. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF. 8. Under steady state (non-transient) conditions, IOL must be externally limited as follows: 15mA (*NOTE: This is 85C specification.) Maximum IOL per port pin: 26mA Maximum IOL per 8-bit port: 71mA Maximum total IOL for all outputs: If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. 9. ALE is tested to VOH1, except when ALE is off then VOH is the voltage specification. 10. Pin capacitance is characterized but not tested. Pin capacitance is less than 25pF. Pin capacitance of ceramic package is less than 15pF (except EA it is 25pF). 1996 Aug 16 19 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 AC ELECTRICAL CHARACTERISTICS Tamb = 0C to +70C or -40C to +85C, VCC = 5V 10%, VSS = 0V1, 2, 3 16MHz CLOCK SYMBOL FIGURE PARAMETER MIN MAX VARIABLE CLOCK MIN MAX UNIT 3.5 16 MHz 1/tCLCL 13 Oscillator frequency Speed versions : E tLHLL 13 ALE pulse width 85 2tCLCL-40 ns tAVLL 13 Address valid to ALE low 22 tCLCL-40 ns tLLAX 13 Address hold after ALE low 32 tLLIV 13 ALE low to valid instruction in tLLPL 13 ALE low to PSEN low 32 tCLCL-30 ns tPLPH 13 PSEN pulse width 142 3tCLCL-45 ns tCLCL-30 150 in4 ns 4tCLCL-100 82 tPLIV 13 PSEN low to valid instruction tPXIX 13 Input instruction hold after PSEN tPXIZ 13 Input instruction float after PSEN 37 tCLCL-25 ns tAVIV 13 Address to valid instruction in4 207 5tCLCL-105 ns tPLAZ 13 PSEN low to address float 10 10 ns 0 3tCLCL-105 ns 0 ns ns Data Memory tRLRH 14, 15 RD pulse width 275 6tCLCL-100 ns tWLWH 14, 15 WR pulse width 275 6tCLCL-100 ns tRLDV 14, 15 RD low to valid data in tRHDX 14, 15 Data hold after RD tRHDZ 14, 15 Data float after RD 65 2tCLCL-60 ns tLLDV 14, 15 ALE low to valid data in 350 8tCLCL-150 ns tAVDV 14, 15 Address to valid data in 397 9tCLCL-165 ns tLLWL 14, 15 ALE low to RD or WR low 137 3tCLCL+50 ns tAVWL 14, 15 Address valid to WR low or RD low 122 4tCLCL-130 ns tQVWX 14, 15 Data valid to WR transition 13 tCLCL-50 ns tWHQX 14, 15 Data hold after WR 13 tCLCL-50 ns Data valid to WR high 287 147 0 tQVWH 15 tRLAZ 14, 15 RD low to address float tWHLH 14, 15 RD or WR high to ALE high 23 5tCLCL-165 0 239 3tCLCL-50 ns 7tCLCL-150 0 103 tCLCL-40 ns ns 0 ns tCLCL+40 ns External Clock tCHCX 17 High time 20 20 tCLCL-tCLCX ns tCLCX 17 Low time 20 20 tCLCL-tCHCX ns tCLCH 17 Rise time 20 20 ns tCHCL 17 Fall time 20 20 ns tXLXL 16 Serial port clock cycle time 750 12tCLCL ns tQVXH 16 Output data setup to clock rising edge 492 10tCLCL-133 ns tXHQX 16 Output data hold after clock rising edge 8 2tCLCL-117 ns tXHDX 16 Input data hold after clock rising edge 0 0 ns Shift Register tXHDV 16 Clock rising edge to input data valid 492 10tCLCL-133 ns NOTES: 1. Parameters are valid over operating temperature range unless otherwise specified. 2. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF. 3. Interfacing the 80C52/54/58 to devices with float times up to 45ns is permitted. This limited bus contention will not cause damage to Port 0 drivers. 4. See application note AN457 for external memory interfacing. 1996 Aug 16 20 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 AC ELECTRICAL CHARACTERISTICS Tamb = 0C to +70C or -40C to +85C, VCC = 5V 10%, VSS = 0V1, 2, 3 24MHz CLOCK SYMBOL FIGURE 1/tCLCL 13 PARAMETER MIN Oscillator frequency Speed versions : I (24MHz) : N (33MHz) 3.5 MAX VARIABLE CLOCK4 MIN MAX 3.5 33 33MHz CLOCK MIN MAX 3.5 33 24 UNIT MHz tLHLL 13 ALE pulse width 43 2tCLCL-40 21 ns tAVLL 13 Address valid to ALE low 17 tCLCL-25 5 ns tLLAX 13 Address hold after ALE low 17 tLLIV 13 ALE low to valid instruction in tLLPL 13 ALE low to PSEN low 17 tPLPH 13 PSEN pulse width 80 tPLIV 13 PSEN low to valid instruction in tPXIX 13 Input instruction hold after PSEN tPXIZ 13 Input instruction float after PSEN 17 tCLCL-25 5 ns tAVIV 13 Address to valid instruction in 128 5tCLCL-80 70 ns tPLAZ 13 PSEN low to address float 10 10 10 ns tCLCL-25 102 ns 4tCLCL-65 tCLCL-25 5 3tCLCL-45 65 0 55 ns 45 3tCLCL-60 0 ns ns 30 0 ns ns Data Memory tRLRH 14, 15 RD pulse width 150 6tCLCL-100 82 tWLWH 14, 15 WR pulse width 150 tRLDV 14, 15 RD low to valid data in tRHDX 14, 15 Data hold after RD tRHDZ 14, 15 Data float after RD 55 2tCLCL-28 32 ns tLLDV 14, 15 ALE low to valid data in 183 8tCLCL-150 90 ns tAVDV 14, 15 Address to valid data in 210 9tCLCL-165 105 ns tLLWL 14, 15 ALE low to RD or WR low 75 140 ns tAVWL 14, 15 Address valid to WR low or RD low 92 4tCLCL-75 45 ns tQVWX 14, 15 Data valid to WR transition 12 tCLCL-30 0 ns tWHQX 14, 15 Data hold after WR 17 tCLCL-25 5 ns tQVWH 15 Data valid to WR high 162 7tCLCL-130 80 ns tRLAZ 14, 15 RD low to address float tWHLH 14, 15 RD or WR high to ALE high 17 6tCLCL-100 118 0 82 5tCLCL-90 0 175 3tCLCL-50 0 67 ns 60 0 3tCLCL+50 40 0 tCLCL-25 ns tCLCL+25 5 ns ns 0 ns 55 ns External Clock tCHCX 17 High time 17 17 tCLCL-tCLCX ns tCLCX 17 Low time 17 17 tCLCL-tCHCX ns tCLCH 17 Rise time 5 5 ns tCHCL 17 Fall time 5 5 ns tXLXL 16 Serial port clock cycle time 505 12tCLCL 360 ns tQVXH 16 Output data setup to clock rising edge 283 10tCLCL-133 167 ns tXHQX 16 Output data hold after clock rising edge 3 2tCLCL-80 tXHDX 16 Input data hold after clock rising edge 0 0 Shift Register ns 0 ns tXHDV 16 Clock rising edge to input data valid 283 10tCLCL-133 167 ns NOTES: 1. Parameters are valid over operating temperature range unless otherwise specified. 2. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF. 3. Interfacing the 80C52/54/58 to devices with float times up to 45ns is permitted. This limited bus contention will not cause damage to Port 0 drivers. 4. Variable clock is specified for oscillator frequencies greater than 16MHz to 33MHz. For frequencies equal or less than 16MHz, see 16MHz "AC Electrial Characteristics", page 20. 1996 Aug 16 21 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 EXPLANATION OF THE AC SYMBOLS P - PSEN Q - Output data R - RD signal t - Time V - Valid W - WR signal X - No longer a valid logic level Z - Float Examples: tAVLL = Time for address valid to ALE low. tLLPL =Time for ALE low to PSEN low. Each timing symbol has five characters. The first character is always `t' (= time). The other characters, depending on their positions, indicate the name of a signal or the logical status of that signal. The designations are: A - Address C - Clock D - Input data H - Logic level high I - Instruction (program memory contents) L - Logic level low, or ALE tLHLL ALE tAVLL tLLPL tPLPH tLLIV tPLIV PSEN tLLAX A0-A7 PORT 0 tPXIZ tPLAZ tPXIX A0-A7 INSTR IN tAVIV PORT 2 A0-A15 A8-A15 SU00006 Figure 13. External Program Memory Read Cycle ALE tWHLH PSEN tLLDV tLLWL tRLRH RD tAVLL tLLAX tRLAZ PORT 0 tRHDZ tRLDV tRHDX A0-A7 FROM RI OR DPL DATA IN A0-A7 FROM PCL INSTR IN tAVWL tAVDV PORT 2 P2.0-P2.7 OR A8-A15 FROM DPF A0-A15 FROM PCH SU00025 Figure 14. External Data Memory Read Cycle 1996 Aug 16 22 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 ALE tWHLH PSEN tWLWH tLLWL WR tLLAX tAVLL tWHQX tQVWX tQVWH A0-A7 FROM RI OR DPL PORT 0 DATA OUT A0-A7 FROM PCL INSTR IN tAVWL PORT 2 P2.0-P2.7 OR A8-A15 FROM DPF A0-A15 FROM PCH SU00026 Figure 15. External Data Memory Write Cycle INSTRUCTION 0 1 2 3 4 5 6 7 8 ALE tXLXL CLOCK tXHQX tQVXH OUTPUT DATA 0 1 2 WRITE TO SBUF 3 4 5 6 7 tXHDX tXHDV SET TI INPUT DATA VALID VALID VALID VALID VALID VALID VALID VALID CLEAR RI SET RI SU00027 Figure 16. Shift Register Mode Timing VCC-0.5 0.45V 0.7VCC 0.2VCC-0.1 tCHCL tCHCX tCLCH tCLCX tCLCL SU00009 Figure 17. External Clock Drive 1996 Aug 16 23 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers VCC-0.5 80C52/80C54/80C58 VLOAD+0.1V 0.2VCC+0.9 VLOAD 0.45V 0.2VCC-0.1 VLOAD-0.1V TIMING REFERENCE POINTS VOH-0.1V VOL+0.1V NOTE: For timing purposes, a port is no longer floating when a 100mV change from load voltage occurs, and begins to float when a 100mV change from the loaded VOH/VOL level occurs. IOH/IOL 20mA. NOTE: AC inputs during testing are driven at VCC -0.5 for a logic `1' and 0.45V for a logic `0'. Timing measurements are made at VIH min for a logic `1' and VIL max for a logic `0'. SU00717 SU00718 Figure 18. AC Testing Input/Output Figure 19. Float Waveform 35 30 MAX ACTIVE MODE ICCMAX = 0.9 X FREQ. + 1.1 25 20 ICC mA 15 TYP ACTIVE MODE 10 MAX IDLE MODE 5 TYP IDLE MODE 4MHz 8MHz 12MHz 16MHz 20MHz 24MHz 28MHz 32MHz 36MHz FREQ AT XTAL1 SU00768 Figure 20. ICC vs. FREQ Valid only within frequency specifications of the device under test 1996 Aug 16 24 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 VCC VCC ICC ICC VCC VCC VCC VCC RST RST VCC P0 P0 EA EA (NC) XTAL2 (NC) XTAL2 CLOCK SIGNAL XTAL1 CLOCK SIGNAL XTAL1 VSS VSS SU00719 SU00720 Figure 21. ICC Test Condition, Active Mode All other pins are disconnected VCC-0.5 Figure 22. ICC Test Condition, Idle Mode All other pins are disconnected 0.7VCC 0.2VCC-0.1 0.45V tCHCL tCHCX tCLCH tCLCX tCLCL SU00009 Figure 23. Clock Signal Waveform for ICC Tests in Active and Idle Modes tCLCH = tCHCL = 5ns VCC ICC VCC VCC RST P0 EA (NC) XTAL2 XTAL1 VSS SU00016 Figure 24. ICC Test Condition, Power Down Mode All other pins are disconnected. VCC = 2V to 5.5V 1996 Aug 16 25 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 internal memory, EA is latched on Reset and all further programming of the EPROM is disabled. When security bits 1 and 2 are programmed, in addition to the above, verify mode is disabled. Security Bits With none of the security bits programmed the code in the program memory can be verified. If the encryption table is programmed, the code will be encrypted when verified. When only security bit 1 (see Table 8) is programmed, MOVC instructions executed from external program memory are disabled from fetching code bytes from the Encryption Array 64 bytes of encryption array are initially unprogrammed (all 1s). Table 8. Program Security Bits PROGRAM LOCK BITS1, 2 SB1 SB2 PROTECTION DESCRIPTION 1 U U No Program Security features enabled. (Code verify will still be encrypted by the Encryption Array if programmed.) 2 P U MOVC instructions executed from external program memory are disabled from fetching code bytes from internal memory, EA is sampled and latched on Reset, and further programming of the EPROM is disabled. NOTES: 1. P - programmed. U - unprogrammed. 2. Any other combination of the security bits is not defined. 80C52 ROM CODE SUBMISSION When submitting ROM code for the 80C52, the following must be specified: 1. 8k byte user ROM data 2. 64 byte ROM encryption key 3. ROM security bits. ADDRESS CONTENT BIT(S) COMMENT 0000H to 1FFFH DATA 7:0 User ROM Data 2000H to 201FH KEY 7:0 ROM Encryption Key FFH = no encryption 2020H SEC 0 ROM Security Bit 1 0 = enable security 1 = disable security 2020H SEC 1 ROM Security Bit 2 0 = enable security 1 = disable security Security Bit 1: When programmed, this bit has two effects on masked ROM parts: 1. External MOVC is disabled, and 2. EA is latched on Reset. Security Bit 2: When programmed, this bit inhibits Verify User ROM. If the ROM Code file does not include the options, the following information must be included with the ROM code. For each of the following, check the appropriate box, and send to Philips along with the code: Security Bit #1: Enabled Disabled Security Bit #2: Enabled Disabled Encryption: No Yes 1996 Aug 16 If Yes, must send key file. 26 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 80C54 ROM CODE SUBMISSION When submitting ROM code for the 80C54, the following must be specified: 1. 16k byte user ROM data 2. 64 byte ROM encryption key 3. ROM security bits. ADDRESS CONTENT BIT(S) COMMENT 0000H to 3FFFH DATA 7:0 User ROM Data 4000H to 401FH KEY 7:0 ROM Encryption Key FFH = no encryption 4020H SEC 0 ROM Security Bit 1 0 = enable security 1 = disable security 4020H SEC 1 ROM Security Bit 2 0 = enable security 1 = disable security Security Bit 1: When programmed, this bit has two effects on masked ROM parts: 1. External MOVC is disabled, and 2. EA is latched on Reset. Security Bit 2: When programmed, this bit inhibits Verify User ROM. If the ROM Code file does not include the options, the following information must be included with the ROM code. For each of the following, check the appropriate box, and send to Philips along with the code: Security Bit #1: Enabled Disabled Security Bit #2: Enabled Disabled Encryption: No Yes 1996 Aug 16 If Yes, must send key file. 27 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 80C58 ROM CODE SUBMISSION When submitting ROM code for the 80C58, the following must be specified: 1. 32k byte user ROM data 2. 64 byte ROM encryption key 3. ROM security bits. If submitting a file, the format is as follows: ADDRESS CONTENT BIT(S) COMMENT 0000H to 7FFFH DATA 7:0 User ROM Data 8000H to 801FH KEY 7:0 ROM Encryption Key FFH = no encryption 8020H SEC 0 ROM Security Bit 1 0 = enable security 1 = disable security 8020H SEC 1 ROM Security Bit 2 0 = enable security 1 = disable security Security Bit 1: When programmed, this bit has two effects on masked ROM parts: 1. External MOVC is disabled, and 2. EA is latched on Reset. Security Bit 2: When programmed, this bit inhibits Verify User ROM. If the ROM code file does not include the options, the following information must be included with the ROM code. For each of the following check the appropriate box and send to Philips along with the code: Security Bit #1: Enabled Disabled Security Bit #2: Enabled Disabled Encryption: No Yes 1996 Aug 16 If Yes, must send key file. 28 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers DIP40: plastic dual in-line package; 40 leads (600 mil) 1996 Aug 16 29 80C52/80C54/80C58 SOT129-1 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers PLCC44: plastic leaded chip carrier; 44 leads 1996 Aug 16 80C52/80C54/80C58 SOT187-2 30 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 QFP44: plastic quad flat package; 44 leads (lead length 1.3 mm); body 10 x 10 x 1.75 mm 1996 Aug 16 31 SOT307-2 Philips Semiconductors Product specification CMOS single-chip 8-bit microcontrollers 80C52/80C54/80C58 DEFINITIONS Data Sheet Identification Product Status Definition Objective Specification Formative or in Design This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. Preliminary Specification Preproduction Product This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product Specification Full Production This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product. Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088-3409 Telephone 800-234-7381 Philips Semiconductors and Philips Electronics North America Corporation register eligible circuits under the Semiconductor Chip Protection Act. Copyright Philips Electronics North America Corporation 1996 All rights reserved. Printed in U.S.A.