2.0 mm ERmet Hard Metric Connector System 2.0 mm ERmet Acc. To IEC 61076-4-101 Catalog E 07/10 Edition 1 www.erni.com 137 2.0 mm ERmet Hard Metric Connector System Table of Contents 2.0 mm ERmet Hard Metric Connector System Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141 Complementary Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145 2.0 mm ERmet Hard Metric Connector System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146 Comparsion of 2.0 mm Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149 Design Requirements For Printed Circuit Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151 Alignment Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152 Midplane and Stacking Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152 Shroud Selection Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153 Ordering Information Shroud Selection Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154 Mechanical Specifications and Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 7-Row Electrical Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158 High Frequency Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158 10-Row Electrical Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160 High Frequency Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160 Approval Certificates, Performance Levels And Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162 Right Angle Female Connectors Type A for Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163 Vertical Male Connectors Type A for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 Vertical Female Connectors Type A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170 Right Angle Female Connectors Type B for Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174 Vertical Male Connectors Type B for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177 Vertical Female Connectors Type B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183 Right Angle Female Connectors Type AB for Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188 Vertical Male Connectors Type AB for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .191 Right Angle Female Connectors Type C for Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .193 Vertical Male Connectors Type C for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195 Vertical Female Connectors Type C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .198 Right Angle Female Connectors Type D for Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202 Vertical Male Connectors Type D for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .204 Vertical Female Connectors Type D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .206 Right Angle Female Connectors Type E for Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .208 Verticale Male Conneactors Type E for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .210 Verticale Female Connectors Type E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .212 Right Angle Female Connectors Type DE for Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .214 Verticale Male Connectors Type DE for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216 Right Angle Female Connectors Type F for Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .218 Verticale Male Connectors Type F for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .220 Verticale Female Connectors Type F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .222 Right Angle Female Connectors Type L for Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224 Verticale Male Connectors Type L for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .226 Right Angle Female Connectors Type M for Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .228 Verticale Male Connectors Type M for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 Right Angle Female Connectors Type N for Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .232 Verticale Male Connectors Type N for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .234 Shrouds Type A for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .236 Shrouds Type B for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .239 Shrouds Type C for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .243 Shrouds Type AB for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .245 Shrouds Type D for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249 Shrouds Type E for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251 Shrouds Type F for Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .253 138 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Table of Contents Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Right Angle Female Monoblock Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255 Vertical Male Monoblock Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .257 Dust Covers For Type A, B, AB, D, E and DE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .259 Coding Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261 Guide Pin for ERmet 10 Row Type D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262 Special Contacts for Type L, M and N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .263 Modular press-fit tools for male and female connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .264 Press-In-Tools For The Female Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .265 Press-In-Tools For The Male Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .266 Toolholder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .266 3U CompactPCI(R) Daughter Card Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .267 3U CompactPCI(R) Backplane Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .268 6U CompactPCI(R) Daughter Card Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .269 6U CompactPCI(R) Backplane Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .270 9U 10-Row 2mm Daughter Card Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .271 9U 10-Row 2mm Backplane Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .272 IEEE 1301 Daughter Cards for IEC 61076-4-101 2mm HM Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .273 IEEE 1301 Backplane Layouts For IEC 61076-4-101 2mm HM Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .274 VME64 Extensions Daughter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .275 VME64 Extensions Backplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .276 64 Bit CompactPCI(R) System Slot Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277 32 Bit CompactPCI(R) System Slot Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .279 32 Bit CompactPCI(R) Peripheral Slot Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .280 cPCI Computer Telephony P4 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .281 cPCI Computer Telephony Safety Classifications for J4/P4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .282 cPCI Computer Telephony P5 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .283 cPCI Computer Telephony Safety Classifications for J5/P5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .284 PXI Generic Peripheral Slot Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .285 PXI System Slot Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .286 PXI Star Trigger Slot Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .287 VME64x on CompactPCI(R) J4/P4 and J5/P5 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .288 Single PMC's I/O Signal Mapping to CompactPCI(R) 3U J2 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .289 PMC Mezzanine Card I/O Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .289 IP Mezzanine Module I/O Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .291 Bellcore Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .293 Glossary Of Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .294 2ERNI Customer Request Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300 Right Angle Male Connectors Type A for Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .301 Right Angle Male Connectors Type B for Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .303 Right Angle Male Connectors Type C for Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .305 ERmet Thru Hole Reflow (THR) Female Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .307 CompactPCI Connectors acc. to PIGMG 2.0 Rev. 3.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .309 ERmet(R) Power Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .315 Electrical and Mechanical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .316 Derating Curve and PTH Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .318 Right Angle Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .319 Vertical Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .325 1 2.0 mm ERmet Hard Metric Connector System Introduction The ERmet 2mm H.M. connector line from ERNI offers unparalleled performance and flexibility for today's high performance circuit designs. Since its introduction in 1993, this product line has expanded and now offers almost every module configuration possible in a board to backplane interconnect system. Standard and reverse configurations are available including shielded vertical females, stacking designs, stamped power connectors and cable systems. This connector system has now become the standard for board to backplane applications. The ERmet 2mm H.M. connector system has achieved widespread acceptance and popularity as the interconnect system chosen for CompactPCI. It is also widely used by OEMs serving the telecommunications and networking industry segments. It has achieved this unparalleled acceptance due to its high frequency performance, its wide selection of modular components and its cost-benefit ratio. This connector is supported by one of the industry's most comprehensive international connector standards, IEC 61076-4-101. Whether you are developing a new backplane, a high performance CPU or I/O card or integrating a sophisticated hybrid system, ERNI has anticipated your needs. The ERNI team stands ready to partner with you to develop the most efficient solution to your design challenge. 140 Catalog E Features * Modular connectors with 2.0 mm signal contact pitch for backplanes and daughter cards. * High density board to backplane connector system. * Up to 8 signal rows plus two shield rows for optimum performance. * Three levels of sequential mating for front or rear hot swap applications. 1.5 mm increments. * 15 standard contacts available for any pin loading requirement. * Complete line of complementary accessories to include stamped power connectors, color coded coding keys, latching shrouds, cable connectors, ground return shields, high frequency, and high power contacts. * Superior female connector contact design provides a uniform signal path. * Comply to the international standard IEC 61076-4-101. * For networking, telecommunications, high performance computing and other demanding applications. 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Product Overview latches. For circuit design versatility, the connectors are offered with a selection of contacts including signal, high power, high frequency and coaxial. They are available in 50mm, 44 mm, 38 mm, and 25mm modules for end-to-end stacking without contact loss. The dual beam female contact design provides equalized signal path lengths which results in virtually identical propagation times for each contact row. Type A Connector * 110 signal contacts. * 44 shield contacts. * 50 mm long including the multifunction area for coding keys. * Integral pre-alignment guide and polarizing pins. * Optional locating pegs for printed circuit board (PCB) mounting. * 3 contact lengths for sequential mating. Type B Connector * 125, 110 and 95 signal contacts. * 50 shield contacts. * 50 mm, 44 mm and 38 mm long without the multifunction area. * 3 contact lengths for sequential mating. Type C Connector * 55 signal contacts. * 22 shield contacts. * 25 mm long. * For end positions only. * Pre-alignment guide pins. * Optional locating pegs for printed circuit board (PCB) mounting. * 3 contact lengths for sequential mating. Type D Connector * 176 signal contacts. * 44 shield contacts. * 50 mm long including the multifunction area for coding keys. * Integral pre-alignment guide and polarizing pins. * Optional locating pegs for printed circuit board (PCB) mounting. * Positions for optional early mate ground pin. * 3 contact lengths for sequential mating. Type E Connector * 200 signal contacts. * 50 shield contacts. * 50 mm long without the multifunction area. * 3 contact lengths for sequential mating. Type F Connector * 88 signal contacts. * 22 shield contacts. * 25 mm long. * For end positions only * Pre-alignment guide pins. * Optional locating pegs for printed circuit board (PCB) mounting. * 3 contact lengths for sequential mating. Catalog E 07/10 Edition 1 2.0 mm ERmet ERmet 2mm H.M. connectors are a versatile, cost-effective board-to-backplane solution for today's high performance, high density applications. The ERmet 2mm H.M. line consists of 26 different module types including matching shrouds for midplane, stacking and cable applications, cable connectors, power modules, upper and lower ground return shields, coding keys and cable www.erni.com 141 2.0 mm ERmet Hard Metric Connector System Product Overview 142 Type A Ground Return Shield * Upper and lower shields for Type A connectors. * Upper shield available integrated with female connector or as separate component. Type B Ground Return Shield * Upper and lower shields for the Type B female connectors. * Upper shield available integrated with female connector or as separate component. Type C Ground Return Shield * Upper and lower shields for Type C and M connectors. * Upper shield available integrated with female connector or as separate component. Type D Ground Return Shield * Upper and lower shields for Type D connectors. * Upper shield available integrated with female connector or as separate component. Type E Ground Return Shield * Upper and lower shields for the Type E female connectors. * Upper shield available integrated with female connector or as separate component. Type F Ground Return Shield * Upper and lower shields for Type F connectors. * Upper shield available integrated with female connector or as separate component. Type L Connector * 6 special contact cavities. * 50 mm long. * Multifunction area for coding keys. * Integral pre-alignment guide and polarizing pins. * Optional locating pegs for printed circuit board (PCB) mounting. Type M Connector * 3 special contact cavities. * 55 signal contacts. * 50 mm long. * Multifunction area for coding keys. * Integral pre-alignment guide and polarizing pins. * Optional locating pegs for printed circuit board (PCB) mounting. Type N Connector * 3 special contact cavities. * 25 mm long. * For end positions only * Pre-alignment guide pins. * Optional locating pegs for printed circuit board (PCB) mounting. Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Product Overview 2.0 mm ERmet Type A Vertical Female Connector * 110 signal contacts. * 44 shield contacts. * 50 mm long including the multifunction area for coding keys. * Pre-alignment guide and integral polarizing pins. * Optional shields. * Extended terminals and spacers available. Type B Vertical Female Connector * 125, 110 and 95 signal contacts. * 50, 44 and 38 shield contacts. * 50 mm, 44 mm and 38 mm long without a multifunction area. * Optional shields. * Extended terminals and spacers available. Type C Vertical Female Connector * 55 signal contacts. * 22 shield contacts. * 25 mm long. * For end positions only * Pre-alignment guide pins. * Optional locating pegs for printed circuit board (PCB) mounting. * Optional shields. * Extended terminals and spacers available. Type AB25 Right Angle Female * 125 signal contacts. * 44 shield contacts. * 50 mm long. * Integral prealignment guide and polarizing pins. * AB compatible males also available. Type AB22 Right Angle Female * 110 signal contacts. * 40 shield contacts. * 44 mm long. * Integral prealignment guide and polarizing pins. * AB compatible males also available. Type AB19 Right Angle Female * 95 signal contacts. * 32 shield contacts. * 38 mm long. * Integral prealignment guide and polarizing pins. * AB compatible males also available. Type DE Right Angle Female * 200 signal contacts. * 50 shield contacts. * 50 mm long. * Integral prealignment guide and polarizing pins. * DE compatible males also available. Connector Coding System * Up to 70 unique male and female coding keys. * For use in the multifunction center of the Type A, D, L and M male or female connectors. * Low cost, industry standard design. * Easy snap-in installation - no epoxy adhesive required. * Bright colors for quick visual identification conform to industry standard. * Crush resistant construction, exceeds IEC requirements. Catalog E 07/10 Edition 1 www.erni.com 143 2.0 mm ERmet Hard Metric Connector System Product Overview Type D Vertical Female Connector * 176 signal contacts. * 44 shield contacts. * 50 mm long including the multifunction area for coding keys. * Pre-alignment guide and integral polarizing pins. * Optional shields. 144 Type E Vertical Female Connector * 200 signal contacts. * 50 shield contacts. * 50 mm long without a multifunction area. * Optional shields. Catalog E 07/10 Type F Vertical Female Connector * 88 signal contacts. * 22 shield contacts. * 25 mm long. * For end positions only * Pre-alignment guide pins. * Optional shields. Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Complementary Components 2.0 mm ERmet Type A Shroud * 4 heights for printed circuit boards (PCBs) 1.6 to 6.0 mm thick. * 50 mm and 38 mm long. * Multifunction area for coding keys. Type B Shroud * 4 heights for printed circuit boards (PCBs) 1.6 to 6.0 mm thick. * 50 mm, 44 mm and 38 mm long. Type C Shroud * 4 heights for printed circuit boards (PCBs) 1.6 to 6.0 mm thick. * 25 mm long. * For end positions only. Type AB 19 & AB 25 Shroud * 38 mm and 50 mm respectively. * Integral pre-alignment and guide pins. * 4 heights for printed circuit boards (PCBs) 1.6 to 6.0 mm thick. Type AB 22 Shroud * 44 mm long. * Integral pre-alignment and guide pins. * 4 heights for printed circuit boards (PCBs) 1.6 to 6.0 mm thick. Optional Latch Arm * Can be added to standard ERmet shroud body. * Spring action latch. * Easy installation, no tools required. Cable System * Compatible with ERmet latching shrouds. * 1 x 7 or 1 x 5 stackable housings can be joined together. * Maintains "z" and "f" row shield path. * High frequency contact design. * Molded strain relief. Male & Female Power Module * Closed entry female connector for backplane. * 3 pin levels for sequential mating. * 8 ampere, per contact. * Pressfit, flat rock assembly. Monoblock Modules * Male and Female monoblock modules. * Optional integrated coding keys for 3.3V, 5.0V or Telecom applications. * Multifunction area for coding keys. * Available in a variety of configurations 94 or 100 mm long. Catalog E 07/10 Edition 1 www.erni.com 145 2.0 mm ERmet Hard Metric Connector System Comparsion of 2.0 mm Connectors B = A = 17 23.8 .80 0 m mm m A 2.0 mm Connector For CompactPCI Needs To Be Different. Here's Why. When you're choosing a 2.0 mm connector for your product, it pays to give your choice a little extra thought. Just knowing a connector is a 2.0 mm connector is not enough - there are really three distinctly separate and non-intermateable connector lines. They are the Futurebus style, the HDM style and the Hard Metric style, such as the ERmet 2mm H.M. from ERNI for CompactPCI architecture. All three connector systems use a 2.0 mm grid and are offered in modular formats, but there the similarity ends. Each line has different printed circuit board hole sizes, contact sizes, shield configurations, keying methods and electrical characteristics. In short, there are very few similarities beyond the 2.0 mm grids they share. All three 2.0 mm connector designs consist of multi-row pin headers on the backplane, right angle female connectors on the daughter card and a 2.0 mm grid spacing. One immediate difference is in terminal area design. The HDM style has exposed terminals on the right angle daughter card female connector, while the Futurebus and Hard Metric designs have encapsulated terminals. The 5+2 row Hard Metric backplane connector is 3.0 mm more narrow than the 5+2 row Futurebus connector. The 7 (5+2) row Hard Metric connector is more narrow even than the 6 row HDM connector. The Hard Metric design preserves more space on the backplane for components that must be placed between the connectors. The mating distances also differ between the three product lines. Mating distance is measured from the rear edge of the daughter card to the front surface of the backplane when the daughter card is fully seated. The Futurebus mating distance is 10 mm, while the mating distance for both Hard Metric and HDM is 12.5 mm. The 12.5 mm measurement is important because it matches the mating distance of the established DIN 41612 connectors and the 2.5 mm IEC 61076-4-100 connector. Matching mating distances allows industries that use Eurocard packaging (IEC 273 or IEEE 1101 or 1101.10) to build systems that combine the popular 96 pin DIN connectors and the newer Hard Metric and HDM connectors. This supports legacy architectures while allowing the addition of new features that require the greater signal density of 2.0 mm connectors. The VME64 Extensions committee chose the Hard Metric connector system for the P0/J0 connector because of this advantage. m .00 m C = 10 7.00 mm 1 = D B = A = 15 21.8 .80 m 0m m m B = A = 14 20.8 .8 - - 21 15.4 .4 m mm m m 2.50 m C = 1 0 mm .0 5 D =1 m .50 m C = 12 0 mm .0 D = 14 ERmet 2mm H.M. Connectors *Trademark of Teradyne Corporation 146 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Comparsion of 2.0 mm Connectors 2.0 mm ERmet Connector Lines Design Criteria HDM TM Futurebus ERNI Hard Metric 5+2/8+2 General Specification Proprietary IEC 1076-4-104 IEC 61076-4-101 Number of Rows (Signal and Ground) 6* 5+2 5+2/8+2 Total Contacts Per Linear Inch 76 88 88/127 Number of Standard Modules 3 7 6/15 Width of Male Housing 15.8 mm 17.8 mm 15.4 mm - 21.4 mm Distance from Daughter Card Edge to Row A 2.50 mm 7.00 mm 1.50 mm Mated Distance from Backplane Front to Row A 15.0 mm 17.0 mm 14.0 mm Signal Mating Levels / Step Distance 3 levels, 0.50 mm each 5 levels, 0.75 mm each 3 levels 1.50 mm each Yes EMI Shielding Yes Yes+ Extended Guidance Features See footnote +++ Add-On Module+ Integrated Coding Locations See footnote +++ Integrated Integrated Coding Combinations Per Location 8 3 70 Yes Yes Yes Yes Yes+ Yes+ Yes Reverse Connector Configuration Vertical Male Standard Connector Configuration Vertical Female Power Contact Modules Yes Yes Coaxial Contact Modules Yes Yes Yes Maximum Contact Resistance of Mated Pair 40 m 50 m 20 m Propagation Delay (max.)++ 235 ps 210 ps 135 ps/190 ps PCB Plated Hole Size 0.70 mm 0.70 mm 0.60 mm Press-Fit Daughter Card Yes Yes Yes Termination Backplane Yes Yes Yes * Shield Pins Implemented Through Signal Pins + Not Defined in (IEC) Specification ++ Published Industry Test Results +++ Integrated in Header and add-on module for female Catalog E 07/10 Edition 1 www.erni.com 147 2.0 mm ERmet Hard Metric Connector System Application Notes The ERmet 2mm H.M. connector system now consists of two basic signal module configurations. The original 5+2 design and the newer 8+2 design for higher pin count requirements. Both connector systems consist of a daughter card mounted, right angle female connector featuring the high performance, low skew patented ERmet leaf contact design and a versatile vertical male header mounted on the backplane. Additionally, this arrangement is particularly effective for midplane application and makes sequential mating easy. ERNI can provide 15 standard pins in any row or position required for your design. This allows for three levels of sequential mating in both the front and rear of the backplane, as well as two shorter terminal lengths for applications which don't require rear feed through pins. For midplane and rear I/O applications, ERNI offers complementary 2.0 mm shrouds, vertical female connectors, cable connectors and latch accessories which are used in conjunction with the long terminal lengths (R1, R2 and R3). Backplane Connector Specific contact loading configurations have already been defined for standard applications and special needs like live insertion on CompactPCI. However, to specify a custom loading configuration, use the ERNI customer request forms located in the back of the catalog. A form is provided for the 5+2 configuration and another form is available for the 8+2 configuration. Features * 3 step lengths in 1.5 mm increments ensure dependable sequential mating. * Both front and rear mating areas meet the same IEC performance level. * 15 pin lengths defined by IEC 61076-4-101. * Long terminal contacts (R1, R2 and R3) require the use of rear shrouds. Daughter Card Connector Two outer rows for shielding purposes Upper Shield F E D C Centerline Centerline Row RowBB B A Printed Circuit Board (PCB) Z 3 mm Insulator thickness Two-sided contact springs Press-fit zone Lower Shield Press-fit zone Backplane Upper Shield 3 mm Two-sided contact springs Insulator thickness I H G F E D Printed Circuit Board (PCB) C Centerline Row B Centerline C L Row B B A Z Two-sided contact springs Press-fit zone Lower Shield Press-fit zone 148 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Product Features 2.0 mm ERmet AB Alignment Option (features) The IEC 61076-4-101 connector standard only provides for connector Types A, B, C, D, E, F, L, M and N. Many customers require a connector with the density of a Type B (25 columns) and with the pre-alignment guide pins of the Type A, D, L and M connectors. This became a particular issue within the CompactPCI computer architecture for rear plug in applications where only B connectors were being used. The problem is that if a plug in card only utilizes Type B connectors, the cards will not have adequate vertical alignment even in the most carefully constructed subrack. The result can be pin stubbing and ultimately serious damage to both the backplane connectors and the female connectors on the daughter cards. For our customers who need a solution to this situation or who need the additional 15 pins that a Type B connector provides, but who also need the vertical alignment that the pre-alignment guide pins afford, ERNI has developed the Type AB connector. This new AB design, which does not allow for coding keys, is now required for rP3 and rP5 shrouds by the current draft PICMG Core specification (draft 3.0). Coding Keys CompactPCI(R) supports both conventional 5.0 V logic and 3.3 V logic. To prevent damage to the system resulting from incorrect insertion of cards with differing logic, coding keys are snapped into the multifunctional area of the male and female connector. This is done with the use of a plastic tool after the connector has been pressed in. The unique, bright color of the coding pairs allows for quick and easy visual identification and differentiation. For the 5.0 V logic, CompactPCI(R) use brilliant blue coding keys, 3.3 V logic use cadmium yellow and Telecom applications use strawberry red. The IEC 61076-4-101 standard defines a unique configuration and color for 70 different coding keys. The ERNI design has special integral supports that exceed the IEC requirements. Catalog E 07/10 Edition 1 www.erni.com 149 2.0 mm ERmet Hard Metric Connector System Product Features 2.5 mm minimum wipe length Male Contact Range The ERmet 2mm H.M. Connector System has one of the longest wipe areas of any connector system as defined in IEC 61076-4-101. This ensures reliable contact mating even under adverse mating conditions. Features include: * 2.5 mm minimum wipe length for all three contact lengths. * The required wipe length for rear applications may be achieved by selecting the proper rear shroud height for the backplane thickness. * IEC standardization completely defines tip blade and contact geometry, thus ensuring intermatability. e d c b a e d c b a 16.5 2.5 14 0.2 max. z a b c d e f z a b c d e f Relation To IEEE 1101.10 And IEC 297.3 The ERmet 2mm H.M. Connector System has been chosen by the PICMG for the CompactPCI bus architecture and the VITA Standards Organization for the VME64 Extensions, PO/JO connector. Both of these applications require this connector to be used in 0.8" wide slots in accordance with IEC 297.3 and IEEE 1101.10 mechanical chassis requirements. This chassis system defines the daughter card location within the card slot, relative to the interboard separation planes. When the ERmet Connector System is used within such a chassis system, the dimensions shown in the drawing will be observed. ERNI has designed the lower shield to avoid any interference with the interboard separation plane. This ensures that the daughter card and shield assembly will not snag or interfere with high components in the adjacent slot during installation or removal. Interboard Separation Plane 6.85 8.63 20.32 15.4 B Row Centerline B Row Centerline 4.07 Interboard Separation Plane 14.0 1.33 Male Contact Selection Options The ERmet 2mm H.M. Connector System offers 15 standard contact lengths that utilize the proven pressfit assembly technique. Within the 15 contact lengths are 3 mating levels, achievable on both the plug-in and rear I/O side. Note you always keep 1.5 mm spacing between levels, for enhanced sequential mating. On the plug-in side, the 3 contact levels are: 8.2 mm, 9.7 mm and 11.2 mm. On the rear I/O side there are 5 pressfit terminal length options: P1, P2, R1, R2, and R3. The P1 and P2 terminal lengths are for standard backplane applications with terminal lengths of 3.7 mm and 4.5 mm respectively. The R1, R2 and R3 terminal lengths are for rear I/O applications with lengths of 13.0 mm, 14.5 mm and 16.0 mm respectively. The optimum terminal length is determined by the printed circuit board thickness, rear shroud height and the desired mating level. For contact plating information, refer to the Mechanical Specifications. To specify custom loading configurations, use the ERNI Customer Request Form. 150 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System 2.0 mm ERmet Compliant Pressfit Pins The ERmet 2mm H.M. connector line utilizes the proven pressfit assembly method. This design was chosen because it is an efficient assembly method that offers a number of benefits over soldering including higher reliability, easier inspection and repairability, and easier installation. In addition, the pressfit method avoids exposing the high layer count printed circuit boards (PCBs) to the additional thermal stress of soldering. Design Requirements For Printed Circuit Boards Plated Through-hole For Pressfitting Signal Contacts, Power Contacts And Shielding Contacts All ERmet 5+2 row and 8+2 row signal contacts are pressfit. In addition, the bladed ERmet power connectors are also pressfit and share the same board plated hole requirements as the male and female signal connectors. The ERmet 2mm H.M. Connectors have been used successfully with reflowed tin-lead, plated tin-lead, immersion tin, organic coatings over bare copper and immersion gold hole plating regimes. The hole recommendations and press in force information shown in this catalog are for reflowed tin-lead and plated tinlead. Additional test data for other hole plating regimes are available through customer service. 0,7 Durchmesser des metallisierten Loches Diameter of finished plated-through hole 0,6 Bohrungsdurchmesser des Loches Diameter of drilled hole 0,02 0,05 min. 0,05 Restringbreite Restring width max. 15 m 1) Sn / SnPb min. 25 m Cu Plated Through-hole For Pressfitting High-current Contacts (Special Contacts For Modules L, M And N) The ERmet Type L, M and N connectors have provisions for high frequency coaxial and high current circular contacts. These contacts have a variety of different plated through-hole requirements. For these, please consult ERNI Customer Service. However, ERNI does offer both 20 Amp and 40 Amp high power pressfit contacts for the L, M, and N connectors, which have the specific plated through-hole requirements shown to the right. Bohrungsdurchmesser 3,1 -0,03 Durchmesser des metallisiertes Loches +0,04 des Loches Diameter of drilled hole 3 -0,06 Diameter of finished plated-through hole Restringbreite min. 0.8 restring width min. 25 m Cu max. 15 m Sn/SnPb 3,6 -0,03 Durchmesser des metallisierten Loches Diameter of finished plated-through hole 1) Bohrungsdurchmesser des Loches Diameter of drilled hole +0,04 3,5 -0,06 min. 0.8 Restringbreite Restring width min. 25 m Cu Maximum Circuit Density The dense ERmet 2.0 mm grid spacing utilizes a 0.6 mm plated through via. This via diameter, together with an appropriate plated annular ring, leaves a 1.0 mm minimum space between adjacent annular rings for trace routing. This space allows for either two equally spaced conductor traces of 0.2 mm (.008") wide or three equally spaced conductors 0.14 mm (.006") wide, as shown in the drawing to the right. This layout can be used to bus two or three rows of the connector on each layer respectively. Many designers bus each row on a separate layer with a ground or power layer between for best signal integrity. max. 15 m Sn/SnPb 1) 2.0 0.2 (.008") 2 traces between pads 2.0 2.0 0.14 (.006") 3 traces between pads Catalog E 07/10 Edition 1 www.erni.com 151 2.0 mm ERmet Hard Metric Connector System Alignment Tolerance Allowed Misalignment Allowed Angular Inclination The pre-alignment pins ensure accurate alignment, eliminating the possibility of pin stubbing on the female insulator. When modules with the pre-alignment feature are used, the following mating tolerances can be accommodated: * Up to 2.0 mm of vertical or horizontal misalignment. * Up to 2 degrees of vertical or horizontal angular inclination. Midplane and Stacking Applications Midplane - inline The most common configuration for mid plane applications is to have a rear shroud over long terminals. The rear shroud is oriented so that the shroud's "a" row lines up with the "a" row of the male connector on the front side of the backplane. In this configuration, the card guides in the front of the backplane line up exactly with those behind the backplane. Midplane - out of line This less common configuration has the "a" row of the shroud aligned with the "e" row of the male connector on the front side of the backplane. In this configuration, the card that plugs into the rear side has the same appearance as the board that plugs into the front side of the backplane. This usually requires a more complex card guide arrangement than the inline configuration. Parallel stacking This configuration has a vertical female connector on a mezzanine board mating into a rear shroud on the rear of a backplane. This is a very popular method often used to connect two or more slots with a PCB which is parallel to the backplane. This is a common solution for switched fabrics such as Raceway or for modular dedicated bused lines such as a special processor to board memory bus. The ERmet vertical female is also available with long tails to allow two levels of stacking. The ERNI vertical female has shields so all male pins can be contacted. Vertical females with long terminals are available for additional levels of stacking. Right Angle Female Shroud Catalog E Male Header Right Angle Female Male Header Right Angle Female Right Angle Female Shroud Male Header Right Angle Female Vertical Female Cable Connector Cable I/O All ERmet rear shrouds can be fitted with optional latch arms. This can be done during backplane assembly or later by the end customer. The latch arms allow the ERmet 2mm cable connector to be retained by the shroud. The ERmet 2mm cable system also mates with the "z" and "f" shield rows. This cable system is a very flexible method for taking high speed signals from one backplane to elsewhere in a system or even to an adjacent backplane. 152 Shroud Shroud Male Header Shroud Latch 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Shroud Selection Information 8.5 8.0 7.5 7.0 6.0 (Dimensions illustrated below) Y-Backplane Thickness (mm) 6.5 5.5 5.0 4.5 4.0 3.5 Examples: * For a backplane thickness of 2.5 mm and the need to accommodate all three rear mating lengths (terminals R1, R2 and R3), a shroud base thickness of 6.1 mm must be used. * With a 5.0 mm thick backplane and a shroud with a 5.3 mm base thickness, only the R1 and R2 terminal length pins may be used. The R3 terminal would be too short to ensure the proper wipe length for reliable mating. * With a 3.0 mm thick backplane and a shroud with a 5.3 mm base thickness any R1, R2 and R3 terminal length pin may be used. 3.0 2.5 2.0 1.5 Height: _________________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _ _ _ _ _R1 ____________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R1 ___________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _ _ _ _ _R2 ____________________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R1 _________________ _________________________________________ _ _ _ _ _R1 ____________________________________ _________________________________________ _________________________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R2 ___________________________ _________________________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R1 ___________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R1 _______ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _ _ _ _ _R3 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R2 _________________ _________________________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R1 _________________ _ _ _ _ _R2 ____________________________________ _ _ _ _ _R1 ____________________________________ _________________________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R3 ___________________________ _________________________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R2 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R2 _______ _________________________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R1 ___________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R1 _______ _________________________________________ _________________________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R3 _________________ _________________________________________ _ _ _ _ _R3 ____________________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R2 _________________ _ _ _ _ _R2 ____________________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R1 _________________ _________________________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R3 _______ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R3 ___________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R2 _______ _________________________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R2 ___________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R3 _ _ _ _ _ _ _ _ _ _ R1 _______ _________________________________________ _ _ _ _ _R3 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ R2 _________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ 14.35 mm 14.95 mm 15.75 mm 16.55 mm 3.9 mm 4.5 mm 5.3 mm 6.1 mm H-Shroud Base Thickness (mm) (Dimensions illustrated below) 3.9 4.5 5.3 6.1 Male Connector Level 3 Level 2 Level 1 11.2 9.7 2.0 mm ERmet After the backplane has been designed and its final overall thickness is determined, it is often challenging to select the proper shroud. Furthermore, a design may specify sequential mating in the rear which requires several different terminal lengths. To accommodate a wide range of backplane thicknesses and up to 3 rear mating levels, ERNI offers shrouds with 4 different base thicknesses. Which base thickness you select depends on both the backplane thickness and the number of terminal lengths you need. Note that due to the extremely long contact wipe length (2.5 mm), several different combinations of pin terminal lengths and shroud base thicknesses may be used to achieve the same functional result. The chart at right shows for each of the four shroud base thicknesses, which connector terminal lengths (R1, R2 or R3) may be used for any specific backplane thickness (1.5 mm to 8.0 mm). 8.2 3.0 Y Backplane R3=13.0 H 3.9 R2=14.5 Shroud Base Thickness R1=16.0 10.5 Rear Shroud Catalog E 07/10 Edition 1 www.erni.com 153 2.0 mm ERmet Hard Metric Connector System Ordering Information Shroud Selection Chart Description Type A25 Shroud Base Thickness (mm) Length (A) (mm) Shroud Part # Tool for Press* Assembly 3.9 49.9 114436 914070 4.5 49.9 054795 914070 5.3 49.9 054794 914070 6.1 49.9 054793 914070 3.9 37.9 NA 914079 (R) CompactPCI rP1 and rP4 positions Type A19 Shroud Type AB25 Shroud Type AB22 Shroud CompactPCI(R) rP2 and rP5 positions Type AB19 Shroud CompactPCI(R) rP3 position Type B25 Shroud Type B22 Shroud Type B19 Shroud Type C11 Shroud 4.5 37.9 923109 914079 5.3 37.9 923108 914079 6.1 37.9 923107 914079 3.9 49.9 114482 914690 4.5 49.9 114483 914690 5.3 49.9 114484 914690 6.1 49.9 114485 914690 3.9 43.9 114425 914691 4.5 43.9 114426 914691 5.3 43.9 114427 914691 6.1 43.9 114428 914691 3.9 37.9 114487 914692 4.5 37.9 114488 914692 5.3 37.9 114489 914692 6.1 37.9 114490 914692 3.9 49.9 114437 914069 4.5 49.9 054797 914069 5.3 49.9 054798 914069 6.1 49.9 054799 914069 3.9 43.9 114619 914083 4.5 43.9 064692 914083 5.3 43.9 064693 914083 6.1 43.9 064694 914083 3.9 37.9 114618 914084 4.5 37.9 064622 914084 5.3 37.9 064623 914084 6.1 37.9 064624 914084 3.9 24.55 114438 914068 4.5 24.55 064172 914068 5.3 24.55 064171 914068 6.1 24.55 064170 914068 Tool for Manual Assembly - - 064202 - Latch Arm - - 064219 - Replacement Locking Wafers - - - 054521 Dimensions shown are for reference purposes only. All dimensions are in millimeters (mm) unless otherwise noted. *The tools are the same tools used to pressfit the equivalent male connectors. The tools listed will only accommodate pins extending no more than 8.7 mm from the inside floor of the shroud. Calculated as follows: [8.7 mm > 16.0 mm - (BP thickness (mm) + shroud base thickness (mm))] 154 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System 2.0 mm ERmet Connector System Modularity And Configuration Modularity The ERmet 2mm H.M. connector has been designed in accordance with IEC 61076-4-101, with eleven basic connector types: A, B, AB, C, D, E, DE, F, L, M and N. These connectors can be assembled end to end in a great variety of combinations but certain guidelines must be followed: You cannot mix 5+2 and 8+2 versions except under some very special situations. Type B connectors cannot be used alone. A Type B connector must be used in conjunction with a module containing a pre-alignment guide such as connector types A, AB, C, L, M or N. Type E connectors cannot be used alone. A Type E connector must be used in conjunction with a module containing a pre-alignment guide such as connector types D, DE or F. Type C, N and F connectors must be assembled at the lower end of a connector stack. Each end of the connector is designed so that the modules "nest" together. This provides additional support for the side walls and makes for a very neat appearance. When shrouds are used on the rear side of a backplane, care must be taken to align the shrouds properly. The correct orientation will depend upon the configuration of the rear plug in cards. For most applications following the "inline" configuration, the rear shrouds will have the convex end detail facing down which is opposite to the arrangement depicted in the detailed drawing on this page. The "a" row of the shroud will match the "a" row of the male connector. 0 L D D 25 50 B A E 75 100 A B DE 125 150 F B M 175 200 N B Male Connector Stacking And Connector End Details 225 250 The ERmet 2mm H.M. Connector System is a modular system designed to be assembled on a 2.0 mm grid. The connectors are designed with a unique locking feature which ties the sidewalls together. This ensures that any stress is shared across an entire connector stack when assembled as a group. The connector's convex top end and concave bottom end fit together, maintaining the dense 2.0 mm grid. The bottom of the VME64 Extensions JO connector is the one exception. It is molded flat across as it is not designed for modular stacking and would otherwise interfere with the DIN 41612 connectors. It can be used in a modular stacking configuration but will not benefit from interlocking sidewalls. A 275 300 AB 325 350 C 375 Connector Bottom Nests With Connector Tops. Catalog E 07/10 Combined Stack Height in mm Edition 1 www.erni.com 155 2.0 mm ERmet Hard Metric Connector System Mechanical Specifications and Performance General Connector Specifications Connector Pitch Temperature Range 2.0 mm -55C to +125C Performance level 3 per 61076-4-101 50 mating cycles Performance level 2 per IEC 61076-4-101 Performance level 1 per IEC 61076-4-101 250 mating cycles 500 mating cycles 0.55 mm hole 0.65 mm hole Pressfit pin insertion (male or female) 36 Newtons (N) typical 25 Newtons (N) typical Contact Normal Force 0.8 Newtons (N)/contact 104 M min @ 100DC Contact Insulation Resistance IEC 512-2 Test 3a Shield 104 M min @ 100 DC Mating and with drawal force per IEC 512-7, Test 13a Contact Ground pin to shield n x 0.75 Newtons (N) maximum (n=number of contacts) n x 1 Newtons (N) maximum (n=number of contacts) Withdrawal force per contact IEC 512-7, Test 16e Contact Ground pin to shield 0.15 Newtons (N) minimum 0.15 Newtons (N) minimum Contact insertion force (per pin) IEC 352-5 paragraph 3.2.2.2 Flammability 36.3 Newtons (N) average (male or female) UL 94 V-0 Hole requirements for daughter card and backplane 0.6 mm 0.05 mm after plating Contact Resistance per IEC 512-2. Test 2a 20 m maximum Male Contact and Housings (Pressfit Version) Housing Material (8+2) and (5+2) UL Assigned Performance Level Categories PBT 30% glass filled PLC 3 Contact Material Contact Plating P1, P2 Contact Plating R1, R2, R3 Contact area Phosphor bronze Gold plated Compliant area Sn Rear terminal Contact area Sn Gold plated Rear terminal Gold plated Right Angle Female Contact and Housings (Pressfit Version) Housing Material (8+2) PBT 30% glass filled Housing Material (5+2) Wafer (8+2) and (5+2) PBT 30% glass filled PBT 30% glass filled UL Assigned Performance Level Categories PLC 3 Contact Material Phosphor bronze Gold plated Contact area Contact Plating Compliant area Sn 0.8 Newtons (N)/contact Contact Normal Force Vertical Female (Pressfit Version) Wafer (8+2) and (5+2) Material LCP 30% glass filled UL Assigned Performance Level Categories PLC 2 Contact Material Contact Plating/Performance Level 156 Contact area Phosphor bronze Gold plated Compliant area Extended Terminals Sn Gold plated Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Mechanical Specifications and Performance 2.0 mm ERmet Ground Return Shields for Right Angle Female Connectors Base material Copper alloy Contact plating per IEC 512 Test 9A Contact fingers Gold plated 250 mating cycles Performance level 2 per IEC 61076-4-101 Hole requirements for daughter card 0.6 0.05 mm after plating Ground Return Shields for Vertical Female Connectors Base material Contact plating per Contact fingers Copper alloy Gold plated IEC 512 Test 9A Terminal plating per Extended terminals Gold plated IEC 512 Test 9A 250 mating cycles 0.6 0.05 mm after plating Performance level 2 per IEC 61076-4-101 Hole requirements for daughter card Shrouds Temperature range -55C to +125C Housing material Flammability PBT 30% glass filled UL 94 V-0 Coding Keys Temperature range Housing material -55C to +125C PC 30% glass filled Flammability Mechanical strength UL 94 HB 300 Newtons (N) Weight 0.3 Grams (G) average Latch Arm Temperature range -65C to +125C Housing material LCP 2000 30% glass filled UL 94 V-O Flammability Cable Connectors Female contact housing Over molding Locking combs Material LCP 30% glass filled Flammability Material UL 94 V-0 LCP 30% glass filled Flammability Material UL 94 V-0 LCP 30% glass filled Material 1.0 grams phosphor bronze Plating Material Gold plated phosphor bronze Plating Gold plated Total weight of plastic material Shield Contact Catalog E 07/10 Edition 1 www.erni.com 157 2.0 mm ERmet Hard Metric Connector System 7-Row Electrical Performance In the Time Domain Reflectometry (TDR) plot shown below, note the connector exhibits an almost ideal, 50 ohm characteristic impedance. This smooth, discontinuity-free, impedance progression is due, in part, to both the uniform contact spacing and constant cross section, as well as the uniform dielectric constant. This is a result of the encapsulated terminals of the right angle female connector. The ERmet line of 2mm H.M. connectors set a new, higher standard for 2.0 mm electrical performance. A collection of test reports is available which completely characterizes the connectors' mechanical and high frequency performance. In addition, ERNI can provide a SPICE (Simulator Program for Integrated Circuit Emulation) model to customers, utilizing advanced circuit simulation methods. 116 0.4 Z r 93 0.3 a b c d e Stripline 75 0.2 61 0.1 50 0 41 0.1 33 0.2 SMAconnector signalinput Stripline Stripline Connector Via Via 21 0.4 25.2780 ns 25.7780 ns t SMA Connector signal ground 27 0.3 26.2780 ns TDR plot showing the impedance progression from a 2mm H.M. connector. Signal ground pattern as shown. High Frequency Characteristics The chart below summarizes the electrical characteristics of a test board with similar pin assignments. Note the remarkably low propagation delay (132 ps) and low total skew (a-e = 46 ps). parameter connector pin row a b c d e capacitance C (f = 100 MHz) 2.5 pF 2.8 pF 2.9 pF 3.1 pF 3.2 pF inductance L (f = 100 MHz) 6.8 nH 7.6 nH 8.3 nH 8.7 nH 10.5 nH characteristic impedance 52 propagation delay* These factors, combined with the low capacitance and low inductance of the connector, make the ERmet 2mm H.M. Connector the best choice for demanding, high speed applications. 52 53 53 57 111 ps 119 ps 126 ps 141 ps 157 ps (86) ps (94) ps (101) ps (116) ps (132) ps signal skew 8 ps 9 ps 14 ps a b c d e Stripline 15 ps maximum 46 ps crosstalk 57 dB (f = 100 MHz) Reflection factor (50 and f = 100 MHz) VSWR (f = 100 MHz) Reflection loss [dB] (f = 100 MHz) ground 53 dB 0.02 0.02 1.04 1.04 34 34 0.03 0.03 0.065 1.06 1.06 1.14 30.5 30.5 24 * The higher value of the propagation delay is measured from solder-side to solder-side (rear side). The signal SMA Connector The measurement values are based on this pin configuration. value in parenthesis is calculated from component-side to component-side (front side). 158 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System 7-Row Electrical Performance 2.0 mm ERmet Current Rating For Various Contact Mounting Configurations Curve C - alternate rows, every other position (chessboard pattern) A 3 Current Carrying Capacity The specifications for contact current rating, dielectric withstanding voltages and creepage and clearance distances are all dependent on the contact loading configuration. For example, if contacts are loaded in a "chessboard pattern," each contact can carry more current than if every contact is loaded. 2.5 2 Curve B - all rows, every other position 1.5 1 Curve A - every position 0.5 20 40 60 80 100 120 140 Ambient Temperature C Dielectric Withstanding Voltage Contact/Contact: Row Designation Row a + c + e Row b + d Row a + b + c Fully Loaded Every Other Position Chessboard Pattern Within the row 750Veff 1500Veff - Between the rows 1500Veff 1500Veff - Within the row 750Veff 1500Veff 1500Veff Between the rows 750Veff 750Veff 1200Veff Row a + b + c + d Row a + b + c + d + e Contact to grounding rows or shielding frame: 750Veff Creepage Distances And Clearances Dependent On Contact Layout Contact/Contact: Fully Loaded Every Other Position Chessboard Pattern Backplane Daughter Card Backplane Daughter Card Backplane Daughter Card Female Male Female Male Female Male Connector Connector Connector Connector Connector Connector Row Designation Row a + c + e Row b + d Row a + b + c Within the row 0.8 0.6 2.5 2.5 - Between the rows 2.5 2.5 2.5 2.5 - - - Within the row 0.8 0.6 2.5 2.5 2.5 2.5 Between the rows 0.8 0.6 0.8 0.6 1.5 1.2 Row a + b + c + d Row a + b + c + d + e Creepage and clearance distances for contacts in the outer contact rows (A and E) to shielding rows (optional) is 0.8 mm. Catalog E 07/10 Edition 1 www.erni.com 159 2.0 mm ERmet Hard Metric Connector System 10-Row Electrical Performance In the Time Domain Reflectometry (TDR) plot shown below, note the connector exhibits an almost ideal, 50 ohm characteristic impedance. This smooth, discontinuity-free, impedance progression is due, in part, to both the uniform contact spacing and constant cross section, as well as the uniform dielectric constant. This is a result of the encapsulated terminals of the right angle female connector. The ERmet line of 2mm H.M. connectors set a new, higher standard for 2.0 mm electrical performance. A collection of test reports is available which completely characterizes the connectors' mechanical and high frequency performance. In addition, ERNI can provide a SPICE (Simulator Program for Integrated Circuit Emulation) model to customers, utilizing advanced circuit simulation methods. High Frequency Characteristics low inductance of the connector, make the ERmet 2mm H.M. Connector the best choice for demanding, high speed applications. The chart below summarizes the electrical characteristics of a test board with similar pin assignments. These factors, combined with the low capacitance and parameter capacitance C [pF] f = 300 MHz inductance L [nH] f = 100 MHz connection pin row d e a b c f g h 1.9 2.3 2.5 2.7 2.8 2.8 3.7 4.0 5.4 6.3 6.9 7.5 8.1 8.9 11.9 15.5 characteristic impedance z = L/C 53 52 53 53 54 56 57 62 propagation delay [ps] 110 120 130 140 150 160 175 190 10 signal skew [ps] 10 10 10 crosstalk [dB] f=300 MHz 15 10 34.9 15 32.7 30.2 -28.61 Reflection factor 50 Ohm f = 300 MHz 0.03 0.02 0.02 0.03 0.04 0.06 0.06 0.11 VSWR f = 300 MHz 1.06 1.04 1.04 1.06 1.08 1.13 1.13 1.25 Reflection loss [dB] f = 300 MHz 30.5 34.0 34.0 30.5 28.0 24.4 24.4 19.2 z a b c d e f g h i 10 9 8 7 6 5 4 3 2 1 ground signal pin shielding pin The measurement values are based on this pin configuration. 160 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System 10-Row Electrical Performance 2.0 mm ERmet Current Rating For Various Contact Mounting Configurations Curve C - alternate rows, every other position (chessboard pattern) A 3 Current Carrying Capacity The specifications for contact current rating, dielectric withstanding voltages and creepage and clearance distances are all dependent on the contact loading configuration. For example, if contacts are loaded in a "chessboard pattern," each contact can carry more current than if every contact is loaded. 2.5 2 Curve B - all rows, every other position 1.5 1 Curve A - every position 0.5 20 40 60 80 100 120 140 Ambient Temperature C Dielectric Withstanding Voltage Contact/Contact: Row Designation Row a+c+e+g Within the row Row b+d+f+h Between the rows Row a+b+c Row a+b+c+d Within the row Row a+b+c+d+e Row a+b+c+d+e+f Row a+b+c+d+e+f+g Between the rows Row a+b+c+d+e+f+g+h Contact to grounding rows or shielding frame: 750Veff Fully Loaded Every Other Position Chessboard Pattern 750Veff 1500Veff 1500Veff 1500Veff - - 750Veff 1500Veff 1500Veff 750Veff 750Veff 1200Veff Creepage Distances And Clearances Dependent On Contact Layout Contact/Contact: Fully Loaded Every Other Position Chessboard Pattern Backplane Daughter Card Backplane Daughter Card Backplane Daughter Card Male Female Male Female Male Female Connector Connector Connector Connector Connector Connector Row Designation Row a+c+e+g Row b+d+f+h Row a+b+c Row a+b+c+d Row a+b+c+d+e Row a+b+c+d+e+f Row a+b+c+d+e+f+g Row a+b+c+d+e+f+g+h Within the row Between the rows 0.8 2.5 0.6 2.5 2.5 2.5 2.5 2.5 - - - - Within the row 0.8 0.6 2.5 2.5 2.5 2.5 Between the rows 0.8 0.6 0.8 0.6 1.5 1.2 Creepage and clearance distances for contacts in the outer contact rows (A and E) to shielding rows (optional) is 0.8 mm. Catalog E 07/10 Edition 1 www.erni.com 161 2.0 mm ERmet Hard Metric Connector System Approval Certificates, Performance Levels And Ordering Information Approval Certificates UL Approved by the American approvals authority (Underwriters Laboratories Inc.) File number E 84703. CSA Tested and found in compliance with the requirements of the Canadian Standards Association (CSA). File numbers LR 62504 or LR 67018. ISO 9001 All ERmet connectors are designed and produced in fully approved ERNI ISO 9001 facilities. Bellcore GR 1217 CORE ERmet connectors are available that meet the requirements of Bellcore GR-1217-CORE for large systems in uncontrolled environments. ECTF ERmet connectors are also available to meet the requirements of the Enterprise Computer Telephony Forum's (ECTF) H.110 specification. Performance Levels 207 Conforms to the requirements of IEC 61076-4-101 performance level 2 ( 250 mating cycles) in the contact area. For detailed information, see Mechanical Specifications and Performance. IEC 917 And IEC 61076-4-101 The ERmet Connector System meets the requirements of IEC 61076-4-101 which was developed in accordance with the requirements of IEC 917 the standard for for Hard Metric mounting systems. IEEE 1301 And IEEE 1101 And IEEE 1101.10 ERmet connectors were developed to meet the demanding board to backplane physical architecture of IEEE 1301 and have been adapted to meet the requirements of IEEE 1101 and IEEE 1101.10. PICMG ERmet connectors have been adapted to meet the requirements of the CompactPCI specification as defined by the PICMG. Special length connectors with the required loading have been molded and assembled for these applications. Type AB connectors have been developed for rear transition card applications. 201 Conforms to the requirements of IEC 61076-4-101 performance level 2 ( 250 mating cycles) in both contact and terminal areas. For additional performance levels, consult ERNI Customer Service. Ordering Information All ERNI ERmet 2mm H.M. Connectors for CompactPCI and VME64 Extensions are assigned a six digit part number. The following pages contain part numbers, along with product descriptions of many popular ERNI 2mm H.M. Connectors, complementary components, application, repair and installation tooling. In addition to the configurations listed in this catalog, others are available. Please consult ERNI customer service for more information. 162 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type A for Daughter Cards 2.0 mm ERmet 110 signal contacts 50 mm with multifunction block (for positioning and coding) The ERmet type A female connector provides 110 contacts in a 5 row x 25 position (3 positions used by multifunction cavity), fully loaded configuration. This connector is used in the J1 and J4 positions of the CompactPCI(R) daughter card. The connector is designed for gas tight, pressfit installation and is provided in two different configurations: with integrated upper ground return shields and without integrated upper ground return shields. Lower ground return shields are available separately. The ERmet type A female connector has a multifunction cavity that incorporates pre-alignment guides and accepts optional coding keys. This connector is designed to be used alone or in conjunction with either a type B, C, L, M or N ERmet connector. The type A female is also available with a locating and strain relief peg that helps secure the connector to the printed circuit board (PCB). Dimensional drawings and board hole pattern 25 15 11 1 Catalog E 8 2 4*2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 2 e d c b a 10 * 2 = Compliant zone for thru hole 0.6 0.05 2 20 8 10 * 2 = 20 3- 50 max 1 max 0.4 2 10.8 - 0.2 20.65 - 0.2 1.7 +- 0.05 1 max 11.4 3.2 Id.-Nr. class date 12.25 Board hole pattern ( Component mounting side ) 4 10 * 2 = ( 20 ) 0.6 +- 0.05 plated thru, drill hole 0.7 10 * 2 = ( 20 ) 2 2 + 0.05 nicht not plated thru 0.02 15 13 11 1 2 25 5*2= ( 10 ) f e d c b a 1.5 0.1 all holes 4 07/10 Edition 1 www.erni.com 163 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type A for Daughter Cards Ordering Information Configuration Used For No. of Pins Part Number J1, J4 110 044146 110 044766 Type A Without Shield, Without Peg 25 15 11 1 e d c b a Type A Without Shield, With Peg 25 15 11 1 e d c b a Type A With Shield, Without Peg 25 15 11 1 e d c b a J1, J4 110 064176 e d c b a J4 Telecom 90 104512 rJ4 Telecom 90 104697 Type A With Split Shield, Partially Loaded 25 15 11 1 Type A With Split Shield, Partially Loaded 25 21 18 15 11 1 e d c b a Lower Shield For Type A And AB J1, J4 164 Catalog E 07/10 044446 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type A for Backplanes 2.0 mm ERmet 110 signal contacts 50 mm with multifunction block (for positioning and coding) The ERmet type A vertical male connector provides 110 signal contacts and 44 ground shield contacts in 5+2 row x 25 position (3 positions used by multifunction cavity), fully loaded configuration. This connector is used in the P1 and P4 positions of a CompactPCI(R) backplane. With 15 different standard pin lengths to choose from, this is one of the most versatile connectors available. The connector is designed for gas tight pressfit installation. The ERmet type A male connector has a multifunction cavity that incorporates pre-alignment guides and accepts optional coding keys. This connector is designed to be used alone or in conjunction with either type B, C, L, M or N ERmet connectors. Dimensional drawings and board hole pattern class date Id.-Nr. 0.1 3- 13.45 2 10x2= 20 8 10x2= 20 4x2= 8 compliant zone for thru hole 0.6`0.00.05 25 15 11 1 z a b c d e f 1 max 1 max 50 max Board hole pattern (Component mounting side) 4 10 x 2 = ( 20 ) 0.6 +- 0.05 0.1 all holes plated thru drill hole 0.7 10 x 2 = ( 20 ) 2 2 + 0.05 not plated thru 0.02 15 13 11 1 z a b c d e f ( 12 ) 2 25 4 6x2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. Catalog E 2 - 0.1 15.4 07/10 Edition 1 www.erni.com 165 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type A for Backplanes Ordering Information Configuration Used For No. of Pins Part Number Type A With Peg 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f 110 043136 110 043190 110 043477 110 044148 110 044149 Type A With Peg 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type A With Peg And Extended Terminals For Shrouding 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type A Without Peg 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type A With Peg 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. 166 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type A for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type A With Peg 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f 154 053007 154 054034 154 054185 154 054528 154 064097 Type A With Peg And Extended Terminals For Shrouding 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type A With Peg And Extended Terminals For Shrouding 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type A With Peg 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type A With Peg 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f P1 Per PICMG 2.0 R2.1 Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. Catalog E 07/10 Edition 1 www.erni.com 167 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type A for Backplanes Ordering Information Configuration Used For No. of Pins Part Number Type A With Peg And Extended Terminals For Shrouding 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 2 3 1 z a b P4 154 064688 P4 154 103968 P4 154 103975 P4 Telecom 100 923160 P1 154 923190 c d e f Type A With Peg And Extended Terminals For Shrouding 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type A With Peg And Extended Terminals For Shrouding 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type A Without Peg 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type A With Peg 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. 168 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type A for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type A With Peg And Extended Terminals For Shrouding 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b P1 Special 154 923197 P4 Telecom 100 923212 P1 154 923342 P4 132 923347 c d e f Type A Without Peg And With Extended Terminals 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type A Without Peg And With Extended Terminals 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type A With Extended Terminals For Shrouding 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. Catalog E 07/10 Edition 1 www.erni.com 169 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type A 110 signal contacts 50 mm with multifunction block (for positioning and coding) The ERmet type A vertical female connector provides 110 contacts in a 5 row x 22 position fully loaded configuration. Versions with optional "z" and "f" row shields are available as well as extended terminals for use in stacking applications with rear shrouds. Two spacer heights are also available: 3.1 mm and 9.6 mm to provide additional component clearance. The ERmet type A female connector has a multifunctional cavity that incorporates pre-alignment pins and optional coding keys. The pressfit terminals provide a convenient and reliable gas tight connection. This connector may be used alone or in conjunction with Type B and C vertical female connectors. Dimensional drawings and board hole pattern 12.25 Id.-Nr. Anforderungsstufe class 11.4 170 12 XXXX 1 max. 0.6 3 1 11 3.7 0.2 50 max. 1 max. 15 25 a b 2 c d 8 e 3.65 10 x 2 = 20 8 Lochbild fur Leiterplatte (Bestuckungsseite) 10 x 2 = 0.6 2 10 x 2 = 4x2= 2 20 Board hole pattern (Component mounting side) alle Locher 8 ( 20 ) 10 x 2 = ( 20 ) -all holes 0.05 0.05 2 durchkontaktiert, Bohrloch 0.7 0.02 plated thru, drill hole 0.7 0.02 2 a b c d 1 11 15 25 (8) e 4x2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 3 Datum date Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type A 2.0 mm ERmet * Termination + Board To Board Distance Version 5 Version Without Shield Version 3 Version 4 9.6 3.1 15-16.5 2 15-16.5 3 18.4-20 4 18.4-20 5 25-26.5 3.7 0.2 13 0.2 Board To Board Distance * 1 Board To Board Version Distance 13 0.2 3.7 0.2 3.7 0.2 Version 2 3.1 Version 1 * based on contact level 1 other board to board distances for remaining levels on request (Please contact our Customer Service) Version 10 Version With Shield Version 8 Catalog E 15-16.5 8 18.4-20 9 18.4-20 10 25-26.5 9.6 3.7 0.2 3.1 16 0.2 Distance 15-16.5 7 Board To Board Board To Board Distance * 6 13 0.2 3.7 0.2 13 0.2 16 0.2 3.7 0.2 Note: All dimensions in mm. Version Version 9 Version 7 3.1 Version 6 * based on contact level 1 other board to board distances for remaining levels on request (Please contact our Customer Service) 07/10 Edition 1 www.erni.com 171 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type A Ordering Information Configuration Used For No. of Pins Part Number Type A Without Shield, Without Peg Version 1 * 110 104702 110 114007 110 114009 110 114011 110 114013 XXXX Type A Without Shield, Without Peg Version 2 * XXXX ERNI 114007 2 Type A Without Shield, Without Peg Version 3 * XXXX ERNI 114009 2 Type A Without Shield, Without Peg Version 4 * XXXX ERNI 114011 2 Type A Without Shield, Without Peg Version 5 * XXXX 172 ERNI 114013 2 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type A 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type A With Shield, Without Peg Version 6 * 1 XXXX ERNI 104112 2 110 104112 110 114008 110 114010 110 114012 110 114014 25 Type A With Shield, Without Peg Version 7 * 1 XXXX ERNI 114008 2 25 Type A With Shield, Without Peg Version 8 * 1 XXXX ERNI 114010 2 25 Type A With Shield, Without Peg Version 9 * 1 XXXX ERNI 114012 2 25 Type A With Shield, Without Peg Version 10 * 1 Catalog E XXXX ERNI 07/10 114014 2 25 Edition 1 www.erni.com 173 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type B for Daughter Cards 125 signal contacts 50 mm without multifunction block The ERmet type B female connector provides 125 contacts in a 5 row x 25 position fully loaded configuration. The connector is designed for gas tight, pressfit installation and is provided in two different configurations: with integrated ground return shields and without integrated upper ground return shields. Lower ground return shields are available separately. The ERmet type B female connector has an uninterrupted pin field with no multifunction cavity. This connector is not designed to be used alone, but is intended to be used in conjunction with either a type A, C, L, M or N ERmet connector. Dimensional drawings and board hole pattern 25 1 174 8 Compliant zone for thru hole 0.6 0.05 4*2= 2 24 * 2 = 48 3- 50 max 1 max 0.4 2 10.8 - 0.2 20.65 - 0.2 1.7 +- 0.05 1 max 11.4 Id.-Nr. class date Board hole pattern ( Component mounting side ) 24 * 2 = 0.6 ( 48 ) + 0.05 - 2 plated thru, drill hole 0.7 0.02 25 1 2 ( 10 ) f e d c b a 1.5 0.1 all holes 5*2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 2 e d c b a Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type B for Daughter Cards 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type B Without Shield, Without Peg 25 1 e d c b a 125 044767 e d c b a 125 064179 Type B With Upper Shield, Without Peg 25 1 Type B Without Shield, Without Peg 22 1 e d c b a J2, J5 110 914797 e d c b a J2, J5 110 064785 e d c b a J3 95 914794 e d c b a J3 95 064784 Type B With Upper Shield 22 1 Type B Without Shield, Without Peg 19 1 Type B With Upper Shield 19 Catalog E 1 07/10 Edition 1 www.erni.com 175 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type B for Daughter Cards Ordering Information Configuration Used For No. of Pins Part Number Lower Shield For Type B 044452 Lower Shield For Type B J2, J5 064783 J3 064782 Lower Shield For Type B 176 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type B for Backplanes 2.0 mm ERmet 125 signal contacts 50 mm without multifunction block The ERmet CompactPCI type B vertical male connector provides 125 signal contacts and 50 ground shield contacts in a 5+2 row x 25, fully loaded configuration. With 15 different standard pin lengths to choose from, this is one of the most versatile connectors available. The connector is designed for gas tight pressfit installation. The ERmet type B vertical male connector has an uninterrupted pin field with no multifunction cavity. This connector is not designed to be used alone, but it is intended to be used in conjunction with either a type A, C, L, M or N ERmet connector. Dimensional drawings and board hole pattern 15.4 Catalog E 13.45 32 2 24 x 2 = 48 4x2= 8 compliant zone for thru hole 0.6`0.00.05 1 25 z a b c d e f 1 max 1 max 50 max 24 x 2 = 0.1 0.6 all holes 48 Board hole pattern (Component mounting side) + 0.05 - 2 plated thru, drill hole 0.7 0.02 1 25 ( 12 ) 2 z a b c d e f 6x2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 0.1 date - 0.1 Id.-Nr. class 07/10 Edition 1 www.erni.com 177 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type B for Backplanes Ordering Information Configuration Used For No. of Pins Part Number Type B 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f 125 043137 125 053088 175 053008 175 054293 175 054392 Type B 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type B 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type B 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type B 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. 178 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type B for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type B With Extended Terminals 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f 125 043476 175 054186 175 064522 P2, P5 154 914796 P5 Telecom 154 923162 Type B With Extended Terminals 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type B With Extended Terminals 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type B 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type B 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. Catalog E 07/10 Edition 1 www.erni.com 179 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type B for Backplanes Ordering Information Configuration Used For No. of Pins Part Number Type B With Extended Terminals 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f P2, P5 154 064690 P2 154 923131 P5 Telecom 132 923339 P2 154 923340 P2 132 923345 Type B With Extended Terminals For Shrouding 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type B (AB Compatible) With Extended Terminals For Shrouding 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e C C f Type B (AB Compatible) With Extended Terminals For Shrouding 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 C C z a b c d e C C f Type B (AB Compatible) With Extended Terminals For Shrouding 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e C C f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. 180 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type B for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type B 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c P3 133 103670 P3 133 914793 P3 133 923132 P3 133 923341 P3 114 923346 d e f Type B With Extended Terminals 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type B With Extended Terminals For Shrouding 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type B (AB Compatible) With Extended Terminals For Shrouding 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type B (AB Compatible) With Extended Terminals For Shrouding 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. Catalog E 07/10 Edition 1 www.erni.com 181 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type B for Backplanes Ordering Information Configuration Used For No. of Pins Part Number Type B 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a 112 b 064766 c d e f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. 182 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type B 2.0 mm ERmet 125 signal contacts 50 mm without multifunction block The ERmet type B vertical female connector provides 125 contacts in a 5 row x 25 position fully loaded configuration. Versions with optional "z" and "f" row shields are available as well as extended terminals for use in stacking applications with rear shrouds. Two spacer heights are also available: 3.1 mm and 9.6 mm to provide additional component clearance. The ERmet type B vertical female connector has an uninterrupted contact field and no multifunction cavity. This connector is not designed to be used alone, but is intended to be used with either a Type A or C female ERmet connector. Dimensional drawings and board hole pattern Anforderungsstufe class 11.4 XXXX 50 max. 0.6 1 max. 3.7 0.2 Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. Catalog E Id.-Nr. 12 Datum date 1 max. 1 25 a b 2 c d 8 e 24 x 2 = Lochbild fur Leiterplatte (Bestuckungsseite) 4x2= 2 48 Board hole pattern (Component mounting side) alle Locher 24 x 2 = 0.6 ( 48 ) -all holes 0.05 0.05 2 durchkontaktiert, Bohrloch 0.7 0.02 plated thru, drill hole 0.7 0.02 a 2 b c d 25 4x2= 1 (8) e 07/10 Edition 1 www.erni.com 183 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type B * Termination + Board To Board Distance Version 5 Version 3 Version 4 9.6 3.1 15-16.5 2 15-16.5 3 18.4-20.0 4 18.4-20.0 5 25-26.5 3.7 0.2 13 0.2 Board To Board Distance * 1 Board To Board Version Distance 13 0.2 3.7 0.2 3.7 0.2 Version 2 3.1 Version 1 * based on contact level 1 other board to board distances for remaining levels on request (Please contact our Customer Service) Version 10 Version 8 184 15-16.5 8 18.4-20.0 9 18.4-20.0 10 25-26.5 9.6 3.1 3.7 0.2 16 0.2 Distance 15-16.5 7 Board To Board Board To Board Distance * 6 13 0.2 3.7 0.2 13 0.2 16 0.2 3.7 0.2 Note: All dimensions in mm. Version Version 9 Version 7 3.1 Version 6 * based on contact level 1 other board to board distances for remaining levels on request (Please contact our Customer Service) Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type B 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type B Without Shield, Without Peg Version 1 * XXXX 125 104703 125 114015 125 114017 125 114019 125 114021 Type B Without Shield, Without Peg Version 2 * XXXX ERNI 114015 2 Type B Without Shield, Without Peg Version 3 * XXXX ERNI 114017 2 Type B Without Shield, Without Peg Version 4 * XXXX ERNI 114019 2 Type B Without Shield, Without Peg Version 5 * XXXX Catalog E ERNI 07/10 114021 2 Edition 1 www.erni.com 185 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type B Ordering Information Configuration Used For No. of Pins Part Number Type B With Shield, Without Peg Version 6 * 1 XXXX ERNI 104113 2 125 104113 125 114016 125 114018 125 114020 125 114022 25 Type B With Shield, Without Peg Version 7 * 1 XXXX ERNI 114016 2 25 Type B With Shield, Without Peg Version 8 * 1 XXXX ERNI 114018 2 25 Type B With Shield, Without Peg Version 9 * 1 XXXX ERNI 114020 2 25 Type B With Shield, Without Peg Version 10 * 1 186 XXXX ERNI 114022 2 25 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type B 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type B With Shield, Without Peg Version 6 * 1 XXXX ERNI 114114 2 22 110 114114 110 114134 95 114111 95 114112 95 114133 Type B With F-row Shield, Without Peg Version 6 * 1 XXXX ERNI 114134 2 P2 / P4 22 Type B Without Shield, Without Peg Version 1 * 114111 XXXX Type B With Shield, Without Peg Version 6 * 1 XXXX ERNI 114112 2 19 Type B With F-row Shield, Without Peg Version 6 * 1 Catalog E XXXX ERNI 114133 07/10 P2 / P4 2 19 Edition 1 www.erni.com 187 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type AB for Daughter Cards 125 signal contacts 50 mm without multifunction block The ERmet type AB female connector provides 125 contacts in a 5 row x 25 fully loaded configuration,110 contacts in a 5 row x 22 position fully loaded configuration or 95 pins in a 5 row x 19 position configuration. The 19 position connector is used in the rJ3 location and the 22 position connector is used in the rJ2 and rJ5 locations of the CompactPCI(R) rear transition card. The connector is designed for gas tight, pressfit installation and is provided in two different configurations: with integrated ground return shields and without integrated upper ground return shields. Lower ground return shields are available separately. The ERmet type AB female connector has an uninterrupted pin field with no multifunction cavity but does have integral pre-alignment guides. This connector can be used alone or in conjunction with either a type A, B or C ERmet connector. This connector will provide the necessary alignment for rear transition applications. Dimensional drawings and board hole pattern 25 8 2 e d c b a Compliant zone for thru hole 0.6 0.05 0.05 4x2= 2 24 x 2 = 48 3- 50 max 1 max 0.4 2 3 10.8 - 0.2 20.65 - 0.2 1.7 +- 0.05 1 max 11.4 Id.-Nr. class 24 x 2 = 0.1 0.6 all holes 48 date 13.85 Board hole pattern (Component mounting side) + 0.05 - 2 plated thru, drill hole 0.7 0.02 1 25 ( 12 ) 2 z a b c d e f 6x2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 188 114160 1 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type AB for Daughter Cards 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type AB Without Shield, Without Peg 25 1 e d c b a 125 114154 e 125 114538 rJ2, rJ5 110 104933 rJ2, rJ5 110 114809 rJ3 95 114529 rJ3 95 114810 Type AB With Shield, Without Peg 25 1 d c b a Type AB Without Shield, Without Peg 22 1 e d c b a Type AB With Shield, Without Peg 22 1 e d c b a Type AB Without Shield, Without Peg 1 19 e d c b a Type AB With Shield, Without Peg 1 19 e d c b a Catalog E 07/10 Edition 1 www.erni.com 189 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type AB for Daughter Cards Ordering Information Configuration Used For No. of Pins Part Number Lower Shield For Type A And AB 044446 Lower Shield For Type A And Type AB 114231 Lower Shield For Type A And Type AB 923110 190 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type AB for Backplanes 2.0 mm ERmet 125 signal contacts 50 mm without multifunction block The ERmet type AB vertical male connector provides 125 signal contacts and 44 ground shield contacts in 5+2 row x 25 position, fully loaded configuration. This connector is used in the P1 and P4 positions of a CompactPCI(R) backplane. With 15 different standard pin lengths to choose from, this is one of the most versatile connectors available. The connector is designed for gas tight pressfit installation. The ERmet type AB male connector has an uninterrupted pin field with pre-alignment guides, but does not accept coding keys. This connector can be used alone, or it can be used with either type A, C, L, M or N ERmet connectors. Dimensional drawings and board hole pattern date 0.1 32 2 24 x 2 = 6x2= 48 12 compliant zone for thru hole 0.6`0.00.05 1 25 z a b c d e f 1 max 1 max 50 max Lochbild fuer Leiterplatte Board hole pattern (Bestueckungsseite) (Component mounting side ) 24 x 2 = 0.1 (48 ) alle Locher 0,6 all holes 0,05 durchkontaktiert Bohrloch 0.7 0.02 2 plated thru drill hole 0.70.02 (12) z a b 6x2= c d e f 2 Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. Catalog E - 0.1 15.4 13.45 Id.-Nr. class 07/10 25 15 Edition 1 11 1 www.erni.com 191 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type AB for Backplanes Ordering Information Configuration Used For No. of Pins Part Number Type AB Without Shield, Without Peg R3 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f R2 125 114236 169 114153 169 114539 R1 Type AB With Shield, Without Peg R3 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f R2 R1 Type AB With Shield, Without Peg R3 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f R2 R1 Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. 192 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type C for Daughter Cards 2.0 mm ERmet 55 signal contacts 25 mm extension module The ERmet type C female connector provides 55 contacts in a 5 row x 11 position fully loaded configuration. The connector is designed for gas tight, pressfit installation and is provided in two different configurations: with integrated upper ground return shields and without integrated upper ground return shields. Lower ground return shields are available separately. The ERmet type C female connector has pre-alignment guides. This connector can be used alone or in conjunction with either a type A, B, L, M or N ERmet connector, however, it can only be installed at the lower end of a connector row. The type C female is also available with a locating and strain relief peg that helps secure the connector to the printed circuit board (PCB). Dimensional drawings and board hole pattern 11 1 Catalog E Compliant zone for thru hole 0.6 0.05 2 4*2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 8 2 e d c b a 10 * 2 = 20 3- 25 max 1 max 0.4 2 1.6 10.8 - 0.2 20.65 - 0.2 1.7 +- 0.05 3.95 11.4 class date Id.-Nr. 12.25 Board hole pattern ( Component mounting side ) 10 * 2 = 0.1 ( 20 ) 2 2 + 0.05 all holes not plated thru 0.6 1 5*2= 2 11 0.02 1.5 f e d c b a ( 10 ) + 0.05 - plated thru, drill hole 0.7 3 07/10 Edition 1 www.erni.com 193 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type C for Daughter Cards Ordering Information Configuration Used For No. of Pins Part Number Type C Without Shield, Without Peg 11 1 e 55 044145 55 064198 e d c b a 55 044768 e d c b a 55 064556 d c b a Type C With Shield, Without Peg 11 1 e d c b a Type C Without Shield, With Peg 11 1 Type C With Shield, With Peg 11 1 Lower Shield For Type C 044458 194 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type C for Backplanes 2.0 mm ERmet 55 signal contacts 25 mm extension module The ERmet type C vertical male connector provides 55 signal contacts and 22 ground shield contacts in 5+2 row x 11 position, fully loaded configuration. With 15 different standard pin lengths to choose from, this is one of the most versatile connectors available. The connector is designed for gas tight pressfit installation. The ERmet type C vertical male connector incorporates pre-alignment guides but has no multi function cavity. This connector is designed to be used alone or in conjunction with either type B, L, M or N ERmet connectors, however it can only be installed at the lower end of a connector row. Dimensional drawings and board hole pattern Id.-Nr. class date Catalog E 2 13.45 2 10 x 2 = 4x2= 20 8 compliant zone for thru hole 0.6`0.00.05 1 11 z a b c d e f 3.7 1 max 25 max Board hole pattern (Component mounting side) 10 x 2 = 0.1 all holes not plated thru 3 11 2 0.6 + 0.05 - plated thru 1 drill hole 0.7 0.02 z a b c d e f ( 12 ) 2 ( 20 ) 2 + 0.05 6x2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 3- 0.1 - 0.1 15.4 07/10 Edition 1 www.erni.com 195 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type C for Backplanes Ordering Information Configuration Used For No. of Pins Part Number Type C Without Shield, With Peg 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f 55 043138 55 044147 77 054546 77 053009 Type C Without Shield, With Peg 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type C With Shield, Without Peg 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type C With Shield, With Peg 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. 196 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type C for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type C Without Shield, With Peg And With Extended Terminals 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f 55 054129 77 064550 77 064572 77 103926 Type C With Shield, With Peg And With Extended Terminals 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type C With Shield, With Peg And With Extended Terminals 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type C With Shield, With Peg And With Extended Terminals 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. Catalog E 07/10 Edition 1 www.erni.com 197 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type C 55 signal contacts 25 mm extension module The ERmet type C vertical female connector provides 55 contacts in a 5 row x 11 position fully loaded configuration. Versions with optional "z" and "f" row shields are available as well as extended terminals for use in stacking applications with rear shrouds. Two spacer heights are also available: 3.1 mm and 9.6 mm to provide necessary component clearance. The ERmet type C vertical female has no multifunctional cavity but is equipped with pre-alignment guides. The pressfit terminals provide a convenient and reliable gas tight connection. This connector may be used alone or in conjunction with either a type A or B vertical female connector, however it can only be installed at the lower end of a connector row. Dimensional drawings and board hole pattern 198 Anforderungsstufe class 12.25 11.4 12 1.6 Id.-Nr. XXXX 8 3.7 0.2 25 max. 4 max. 1 4x2= 1 max. 11 2 a b c d e 2 10 x 2 = 20 Lochbild fur Leiterplatte (Bestueckungsseite) Board hole pattern (Component mounting side) alle Locher -all holes 10 x 2 = ( 20 ) 0.05 2 0.6 0.05 durchkontaktiert, Bohrloch 0.7 0.02 plated thru, drill hole 0.7 0.02 2 a b c d 1 11 ( 8) e 4x2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. Datum date Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type C 2.0 mm ERmet * Termination + Board To Board Distance Version 5 Version Without Shield Version 3 Version 4 9.6 3.1 15-16.5 2 15-16.5 3 18.4-20 4 18.4-20 5 25-26.5 3.7 0.2 13 0.2 Board To Board Distance * 1 Board To Board Version Distance 13 0.2 3.7 0.2 3.7 0.2 Version 2 3.1 Version 1 * based on contact level 1 other board to board distances for remaining levels on request (Please contact our Customer Service) Version 10 Version With Shield Version 8 Catalog E 15-16.5 8 18.4-20 9 18.4-20 10 25-26.5 9.6 3.7 0.2 3.1 16 0.2 Distance 15-16.5 7 Board To Board Board To Board Distance * 6 13 0.2 3.7 0.2 13 0.2 16 0.2 3.7 0.2 Note: All dimensions in mm. Version Version 9 Version 7 3.1 Version 6 * based on contact level 1 other board to board distances for remaining levels on request (Please contact our Customer Service) 07/10 Edition 1 www.erni.com 199 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type C Ordering Information Configuration Used For No. of Pins Part Number Type C Without Shield, Without Peg Version 1 * XXXX 55 104704 55 114023 55 114025 55 114027 55 114029 Type C Without Shield, Without Peg Version 2 * XXXX ERNI 114023 2 Type C Without Shield, Without Peg Version 3 * XXXX ERNI 114025 2 Type C Without Shield, Without Peg Version 4 * XXXX ERNI 114027 2 Type C Without Shield, Without Peg Version 5 * XXXX ERNI 114029 2 200 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type C 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type C With Shield, Without Peg Version 6 * 55 104114 55 114024 55 114026 55 114028 55 114030 XXXX Type C With Shield, Without Peg Version 7 * XXXX ERNI 114024 2 Type C With Shield, Without Peg Version 8 * XXXX ERNI 114026 2 Type C With Shield, Without Peg Version 9 * XXXX ERNI 114028 2 Type C With Shield, Without Peg Version 10 * XXXX ERNI 114030 2 Catalog E 07/10 Edition 1 www.erni.com 201 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type D for Daughter Cards 176 signal contacts 50 mm with multifunction block (for positioning and coding) The ERmet type D female connector provides 176 signal contacts and 44 ground shield contacts in a 8 row x 25 position (3 positions used by multifunction cavity), fully loaded configuration. The connector provides for a gas tight, pressfit installation and is designed for two different configurations: with integrated upper ground return shields and without integrated upper ground return shields. The ERmet type D female connector has a multifunction cavity that incorporates pre-alignment guides and accepts optional coding keys. This connector is designed to be used by itself or in conjunction with either a type E or F ERmet 2mm H.M. connector. The type D female is also available with locating and strain relief peg that helps secure the connector to the printed circuit board (PCB). Dimensional drawings and board hole pattern - assemble 25 15 11 1 202 7*2= 2 Compliant zone for thru hole 0.6 0.05 2 10 * 2 = 20 8 10 * 2 = 20 3- 50 max. 0.4 - 0.2 10.8 - 0.2 22.95 10.5 5 1.7 +- 0.05 1 max. 7*1.5= 1 max. 3 Id.-Nr. class 17.4 date 18.25 Board hole pattern ( Component mounting side ) 4 10 * 2 = ( 20 ) 0.6 +- 0.05 0.05 all holes 10 * 2 = ( 20 ) 2 2 + 0.05 not plated thru 0.02 1.5 ( 10.5 ) z/y h g f e d c b a 25 15 13 11 1.5 1.75 plated thru, drill hole 0.7 4 1 7 * 1.5 = Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 14 2 h g f e d c b a Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type D for Daughter Cards 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type D Without Shield, With Peg 25 15 11 1 h g f e d c b a 176 104086 176 104935 176 104415 Type D With Shield, Without Peg 25 15 11 1 h g f e d c b a Type D With Upper Shield, With Peg 25 15 11 1 h g f e d c b a Lower Shield For Type D And DE 103847 Catalog E 07/10 Edition 1 www.erni.com 203 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type D for Backplanes 176 signal contacts 50 mm with multifunction block (for positioning and coding) The ERmet type D vertical male connector provides up to 176 signal contacts and 44 ground shield contacts in 8+2 row x 25 position (3 positions used by multifunction cavity), fully loaded configuration. With 15 different standard pin lengths to choose from, this is one of the most versatile connectors available. The connector is designed for gas tight pressfit installation. The ERmet type D male connector has a multifunction cavity that incorporates pre-alignment guides and accepts optional coding keys. This connector is designed to be used alone or in conjunction with either type E, DE or F ERmet 2mm H.M. connectors. Dimensional drawings and board hole pattern date 204 2 10x2= 20 8 2 10x2= 20 9x2= compliant zone for thru hole 0.6`0.00.05 15 25 11 18 1 z a b c d e f g h y 1 max 1 max 50 max Board hole pattern (Component mounting side) Lochbild fuer Leiterplatte (Bestueckungsseite) 4 10 x 2 = ( 20 ) 0.6 +- 0.05 0.05 all holes plated thru drill hole 0.7 4 10 x 2 = ( 20 ) 2 2 + 0.05 not plated thru 0.02 ( 18 ) z a b c d e f g h y 2 9x2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 3- 0.1 21.4 - 0.1 Id.-Nr. 13.45 class 25 15 13 11 Catalog E 1 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Male Connectors Type D for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type D With Peg 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f g h y 220 104152 220 104517 220 933008 Type D With Peg 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f g h y Type D With Peg and Extended Terminals 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f g h y Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. Catalog E 07/10 Edition 1 www.erni.com 205 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type D 176 signal contacts 50 mm with multifunction block (for positioning and coding) The ERmet type D vertical female connector provides 176 signal contacts in a 8 row x 25 position (3 positions used by multifunction cavity), fully loaded configuration. The connector provides for a gas tight, pressfit installation and is designed for two different configurations: with and without integrated ground return shields. The ERmet type D vertical female connector has a multifunction cavity that incorporates pre-alignment guides and accepts optional coding keys. This connector is designed to be used by itself or in conjunction with either a type E or F ERmet 2mm H.M. connector. Dimensional drawings and board hole pattern 18.25 Datum Id.-Nr. Anforderungsstufe class 17.4 206 124093 12 ERNI 2 50 max. 1 max. 0.6 3 1 11 3.7 0.2 XXXX 1 max. 15 25 a 14 b 2 c 7x2= d e f g h 2 3.65 10 x 2 = 20 8 Lochbild fur Leiterplatte (Bestuckungsseite) 10 x 2 = 0.6 20 Board hole pattern (Component mounting side) 8 ( 20 ) 2 10 x 2 = 10 x 2 = alle Locher ( 20 ) -all holes 0.05 0.05 2 durchkontaktiert, Bohrloch 0.7 0.02 plated thru, drill hole 0.7 0.02 ( 14) a b c e f g 7x2= d 2 Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 3 date h 1 11 15 Catalog E 25 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Female Connectors Type D 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type D Without Shield, Without Peg XXXX ERNI 124093 176 124093 176 124094 2 Type D With Shield, Without Peg 1 XXXX Catalog E ERNI 124094 07/10 2 25 Edition 1 www.erni.com 207 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type E for Daughter Cards 200 signal contacts 50 mm without multifunction block The ERmet type E female connector provides 200 signal contacts and 50 ground shield contacts in a 8 row x 25 position fully loaded configuration.These connectors are also available in an 8+2 row x 22 positions and 8+2 row x 19 positions. The connector provides for a gas tight, pressfit installation and is designed for two different configurations: with integrated upper ground return shields and without integrated upper ground return shields. The ERmet type E female connector has an uninterrupted pin field with no multifunction cavity. This connector is not designed to be used alone, but is intended to be used in conjunction with either a type D, DE or F ERmet 2mm H.M. connector. Dimensional drawings and board hole pattern 25 1 208 Compliant zone for thru hole 0.6 0.05 2 24 * 2 = 48 3- 50 max. 0.4 - 0.2 10.8 - 0.2 22.95 10.5 5 1.7 +- 0.05 1 max. 7*1.5= 1 max. Id.-Nr. class 17.4 date Board hole pattern ( Component mounting side ) 24 * 2 = 0.05 0.6 all holes ( 48 ) + 0.05 - 2 0.02 z/y h g f e d c b a 1 1.5 ( 10.5 ) 25 1.5 1.75 plated thru, drill hole 0.7 7 * 1.5 = Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 7*2= 14 2 h g f e d c b a Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type E for Daughter Cards 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type E Without Shield, Without Peg 25 1 h g f e d c b a 200 104087 200 104416 Type E With Upper Shield, Without Peg 25 1 h g f e d c b a Lower Shield For Type E 103849 Catalog E 07/10 Edition 1 www.erni.com 209 2.0 mm ERmet Hard Metric Connector System Verticale Male Conneactors Type E for Backplanes 200 signal contacts 50 mm without multifunction block The ERmet type E vertical male connector provides 200 signal contacts and 50 ground shield contacts in an 8+2 row x 25 position fully loaded configuration. This connector is also available in an 8+2 row x 22 positions and 8+2 row x 19 positions. With 15 different standard pin lengths to choose from, this is one of the most versatile connectors available. The connector is designed for gas tight pressfit installation. The ERmet type E vertical male connector has an uninterrupted pin field with no multifunction cavity. This connector is not designed to be used alone, but is intended to be used in conjunction with either type D, DE or F ERmet 2mm H.M. connectors. Dimensional drawings and board hole pattern date 210 2 24 x 2 = 2 48 9x2= compliant zone for thru hole 0.6`0.00.05 18 1 25 z a b c d e f g h y 1 max 1 max 50 max Board hole pattern (Component mounting side) 24 x 2 = 0.05 all holes 0.6 + 0.05 - 48 plated thru drill hole 0.7 2 0.02 ( 18 ) z a b c d e f g h y 2 9x2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 3- 0.1 21.4 - 0.1 Id.-Nr. 13.45 class 25 1 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Verticale Male Conneactors Type E for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type E Without Peg 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f g h y 200 104518 250 104153 250 933007 Type E Without Peg 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f g h y Type E Without Peg, With Extended Terminals 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f g h y Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. Catalog E 07/10 Edition 1 www.erni.com 211 2.0 mm ERmet Hard Metric Connector System Verticale Female Connectors Type E 200 signal contacts 50 mm without multifunction block The ERmet type E vertical female connector provides 200 signal contacts in a 8 row x 25 position fully loaded configuration. The connector provides for a gas tight, pressfit installation and is designed for two different configurations: with and without integrated ground return shields. The ERmet type E vertical female connector has an uninterrupted pin field with no multifunction cavity. This connector is not designed to be used alone, but is intended to be used in conjunction with either a type D or F ERmet 2mm H.M. connector. Dimensional drawings and board hole pattern ERNI 17.4 124095 2 50 max. 1 max. 0.6 1 max. 1 25 a 14 b 2 c 7x2= d e f g h 2 24 x 2 = Lochbild fur Leiterplatte (Bestuckungsseite) 24 x 2 = 0.6 48 Board hole pattern (Component mounting side) alle Locher ( 48 ) -all holes 0.05 0.05 2 durchkontaktiert, Bohrloch 0.7 0.02 plated thru, drill hole 0.7 0.02 (14) a b c e f g 7x2= d 2 Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 212 XXXX Anforderungsstufe class 12 Id.-Nr. date 3.7 0.2 Datum h 1 25 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Verticale Female Connectors Type E 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type E Without Shield, Without Peg XXXX ERNI 124095 2 200 124095 200 124096 Type E With Shield, Without Peg 1 XXXX Catalog E ERNI 124096 07/10 2 25 Edition 1 www.erni.com 213 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type DE for Daughter Cards 200 signal contacts 50 mm without multifunction block The ERmet type DE female connector provides 200 signal contacts and 25 ground shield contacts in an 8 row x 25 position fully loaded configuration. The connector provides for a gas tight, pressfit installation and is designed for two different configurations: with integrated upper ground return shields and without integrated upper ground return shields. The ERmet type DE female connector has an uninterrupted pin field and integral pre-alignment guide. This connector can be used alone or in conjunction with type D, E or F ERmet 2mm H.M. connector. Dimensional drawings and board hole pattern 25 1 2 h 14 g f 214 d c b a EE-Zone fur durchkontaktierte 2 24 x 2 = 0.05 Locher O 0.6 Compliant zone for 48 thru hole O 0.6 0.05 3 -0.4 50 max. 1 max. 10.5 3 10.8 -0.2 22.95 -0.2 1.7 0.05 5 7x1.5= 1 max. Anforderungsstufe Id.-Nr. class Datum 17.4 date 19.85 24 x 2 = 0.05 0.6 alle Locher all holes (48 ) 0.05 2 durchkontaktiert, Bohrloch 0.7 0.02 plated thru, 0.02 1.5 h g f e d c b a 25 1.5 drill hole 0.7 7 x 1.5 = ( 10.5) Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 7x2= e 1 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type DE for Daughter Cards 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type DE Without Shield, Without Peg 25 1 h g f e 200 114281 200 124118 d c b a Type DE With Shield, Without Peg 25 1 h g f e d c b a Lower Shield For Type D And DE 103847 Catalog E 07/10 Edition 1 www.erni.com 215 2.0 mm ERmet Hard Metric Connector System Verticale Male Connectors Type DE for Backplanes 200 signal contacts 50 mm without multifunction block The ERmet type DE vertical male connector provides 200 signal contacts and 44 ground shield contacts in a 8+2 row x 25 position fully loaded configuration. With 15 different standard pin lengths to choose from, this is one of the most versatile connectors available. The connector is designed for gas tight pressfit installation. The ERmet type DE vertical male connector has an uninterrupted pin field with pre-alignment guides but does not accept coding keys. This connector can be used alone, or it can be used with either type D or F ERmet connectors. Dimensional drawings and board hole pattern -0.1 3 -0.1 ERNI 114279 2 2 2 24 x 2 = 48 9x2= 18 EE-Zone fur durchkontaktierte Locher O0.60.05 compliant zone for thru hole O0.60.05 25 1 z a b c d e f g h y 1max 1max 50 max Lochbild fuer Leiterplatte (Bestueckungsseite) Board hole pattern (Component mounting side) 24 x 2 = 0.05 alle Loecher all holes 0.6 0.05 durchkontaktiert Bohrloch 0.7 plated thru drill hole 0.7 ( 48 ) 2 0.02 0.02 z a (18 ) b c d 9x2= e f g h y 2 Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 21.4 date XXXX 216 Datum Id.-Nr. 13.45 Anforderungsstufe class 25 1 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Verticale Male Connectors Type DE for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type DE Without Peg 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d 244 114279 200 124335 e f g h y Type DE Without Peg 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f g h y Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. Catalog E 07/10 Edition 1 www.erni.com 217 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type F for Daughter Cards 88 signal contacts 25 mm extension module The ERmet type F female connector provides 88 signal contacts and 22 ground shield contacts in an 8 row x 11 position fully loaded configuration. The connector provides for a gas tight, pressfit installation and is designed for two different configurations: with and without integrated ground return shields. The ERmet type F female connector has integral pre-alignment guides but no multifunction cavity. The type F female is also available with optional locating and strain relief pegs that help secure the connector to the printed circuit board (PCB). This connector is designed to be used alone or with either type D, DE or E ERmet connectors, however it can only be installed at the lower end of a connector field. Dimensional drawings and board hole pattern 11 1 218 7*2= Compliant zone for thru hole 0.6 -0.05 2 10 * 2 = 20 3- 25 max. - 0.2 1.6 10.5 10.8 - 0.2 22.95 0.4 5 1.7 +- 0.05 1 max. 7*1.5= 3.95 Id.-Nr. class 17.4 date 18.25 Board hole pattern ( Component mounting side ) 10 x 2 = 0.05 ( 20 ) 2 2 + 0.05 all holes not plated thru 0.6 3 + 0.05 - 0.02 1.5 ( 10.5 ) z/y h g f e d c b a 11 1.5 1.75 plated thru, drill hole 0.7 1 7 x 1.5 = Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 14 2 h g f e d c b a Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type F for Daughter Cards 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type F Without Shield, With Peg 11 1 h g f e d c b a 88 104088 88 104417 Type F With Shield, With Peg 11 1 h g f e d c b a Lower Shield For Type F 103851 Catalog E 07/10 Edition 1 www.erni.com 219 2.0 mm ERme Hard Metric Connector System Verticale Male Connectors Type F for Backplanes 88 signal contacts 25 mm extension module The ERmet type F vertical male connector provides 88 signal contacts and 22 ground shield contacts in a 8+2 row x 11, fully loaded configuration. With 15 different standard pin lengths to choose from, this is one of the most versatile connectors available. The connector is designed for gas tight pressfit installation. The ERmet type F vertical male connector incorporates pre-alignment guides but has no multifunction cavity. This connector is designed to be used alone. The type F connector can also be used in conjunction with either a type D, E, or DE ERmet connector, however, it can only be installed at the lower end of a connector row. Dimensional drawings and board hole pattern 32 10 x 2 = 20 9x2= compliant zone for thru hole 0.6`0.00.0 11 18 1 z a b c d e f g h y 3.7 1 max 25 max Board hole pattern (Component mounting side) 10 x 2 = 0.05 all holes ( 20 ) 2 2 + 0.05 not plated thru 3 0.6 + 0.05 - plated thru drill hole 0.7 0.02 ( 18 ) z a b c d e f g h y 2 9x2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 220 2 13.45 0.1 - 0.1 21.4 date Id.-Nr. class 11 1 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Verticale Male Connectors Type F for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type F With Peg 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f g h y 88 104519 110 104154 110 933006 Type F With Peg 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f g h y Type F With Peg And Extended Terminals Bestueckungsplan 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f g h y Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. Catalog E 07/10 Edition 1 www.erni.com 221 2.0 mm ERmet Hard Metric Connector System Verticale Female Connectors Type F 88 signal contacts 25 mm extension module The ERmet type F vertical female connector provides 88 signal contacts and in an 8 row x 11 position fully loaded configuration. The connector provides for a gas tight, pressfit installation and is designed for two different configurations: with and without integrated ground return shields. The ERmet type F vertical female connector has integral pre-alignment guides but no multifunction cavity. This connector is designed to be used alone or with either type D or E ERmet connectors, however it can only be installed at the lower end of a connector field. Dimensional drawings and board hole pattern Id.-Nr. 222 XXXX ERNI 124097 2 17.4 3.7 0.2 25 max. 1 max. 18.25 12 1.6 Anforderungsstufe class 4 max. 1 11 2 a 14 b c 7x2= d e f g h 2 10 x 2 = 20 Lochbild fur Leiterplatte (Bestuckungsseite) 10 x 2 = Board hole pattern (Component mounting side) -all holes alle Locher ( 20 ) 0.05 2 0.6 0.05 durchkontaktiert, Bohrloch 0.7 0.02 plated thru, drill hole 0.7 0.02 ( 14) a b c 2 d e f g 7x2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. Datum date h 1 11 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Verticale Female Connectors Type F 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type F Without Shield, Without Peg XXXX ERNI 124097 2 88 124097 88 124098 Type F With Shield, Without Peg XXXX ERNI 124098 2 Catalog E 07/10 Edition 1 www.erni.com 223 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type L for Daughter Cards 6 special contacts 50 mm with multifunction block (for positioning and coding) The ERmet type L female is an insulator that provides up to 6 contact positions for special power or coax contacts in a fully loaded configuration. The ERmet type L female connector has a multifunction cavity that incorporates pre-alignment guides and accepts optional coding keys. This connector is designed to be used alone or in conjunction with either a type B, C, M or N ERmet connector. The type L female is also available with a locating and strain relief peg that helps secure the connector to the printed circuit board (PCB). Dimensional drawings and board hole pattern 2 * 7.5 = 15 12.5 2 * 7.5 = 7.5 15 7.5 3.75 max 224 3.7 12.8 - 0.2 20.65 - 0.2 3.7 + 0.05 - 50 max 3.2 Id.-Nr. 11.4 datum 12.25 Board hole pattern ( Component mounting side ) for free wiring 7.5 7.5 6.25 6.25 7.5 - all holes 7.5 0.1 2.5 2 + 0.1 not plated thru 2 2.5 2.5 2.5 3.5 6. 24 20 16 13 10 6 2 1.3 + 0.1 plated thru Board hole pattern ( Component mounting side ) for press - fitting 8 Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 4.8 3.75 max 24 20 16 13 10 6 2 3.5 +- 0.04 0.06 plated thru Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type L for Daughter Cards 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type L with 6 cavities for special contacts 044579 Catalog E 07/10 Edition 1 www.erni.com 225 2.0 mm ERmet Hard Metric Connector System Verticale Male Connectors Type L for Backplanes 6 special contacts 50 mm with multifunction block The ERmet type L male connector is an insulation body that could be loaded with up to 6 special power or coax contacts in a fully loaded configuration. The ERmet type L male connector has a multifunction cavity that incorporates prealignment guides and accepts optional coding keys. This connector is designed to be used alone or in conjunction with either a type B, C, M, or N ERmet connector. The type L male is available with a locating peg that helps secure the connector to the printed circuit board (PCB). Dimensional drawings and board hole pattern 0.1 3- 13.45 4.8 5.35 2 x 7.5 = 15 12.5 2 x 7.5 = 15 7.5 z 2 d f 3.75 max 3.75 max 50 max Board hole pattern (Component mounting side) for free wiring 7.5 7.5 6.25 7.5 6.25 2 all holes 7.5 0.1 6.1 min - not plated thru 5.9 +0.2 - + 0.05 plated thru 5.5 3.75 24 20 16 13 10 6 2 4.5 Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 226 - 0.1 15.4 date Id.-Nr. Cavaties optional for an additional fixation Board hole pattern (Component mounting side) for press fitting 3.5 -+ 0.04 0.06 plated thru 24 20 16 Catalog E 10 6 2 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Verticale Male Connectors Type L for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type L with 6 cavities for special contacts z 104146 d f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. Catalog E 07/10 Edition 1 www.erni.com 227 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type M for Daughter Cards 3 special and 55 signal contacts 50 mm with multifunction block The ERmet type M female connector provides 55 contacts in a 5 row x 11 position (3 positions used by multifunction cavity), and also 3 contact positions for special power or coax contacts in a fully loaded configuration. The connector is designed for gas tight, pressfit installation and is provided in two different configurations: with and without integrated upper ground return shields. Lower ground return shields are also available separately. The ERmet type M female connector has a multifunction cavity that incorporates pre-alignment guides and accepts optional coding keys. This connector can be used alone or in conjunction with either a type A, B, C, L, or N ERmet connector. The type M female is also available with a center pair of locating and strain relief pegs that help secure the connector to the printed circuit board (PCB). 228 15 8 2 4*2= e d c b a 10 * 2 = 7.5 20 2 * 7.5 = 3.75 max 15 Compliant zone for thru hole 0.6 0.05 50 max 3- 0.4 2 10.8 - 0.2 20.65 - 0.2 1.7 +- 0.05 1 max 11.4 3.2 Id.-Nr. class date 12.25 Board hole pattern ( Component mounting side ) for solder termination 0.1 all holes 6.25 4 10 * 2 = ( 20 ) 0.6 +- 0.05 7.5 7.5 2 1.5 2 0.02 all holes 2.5 2.5 not plated thru 2.5 plated thru, drill hole 0.7 0.1 2.5 2 + 0.1 2 f e d c b a ( 10 ) 25 15 13 10 6 2 1.3 + 0.1 plated thru 5*2= Board hole pattern ( Component mounting side ) for high current contacts with press-fit termination 8 f e d c b a 25 15 13 10 6 2 3.5 +- 0.04 0.06 plated thru 2 Board hole pattern ( Component mounting side ) for coax contacts with press-fit termination 2.5 2 2 2 f e d c b a 8 Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 2 25 4.8 Dimensional drawings and board hole pattern 25 15 13 10 6 2 1 +- 0.09 0.06 plated thru Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type M for Daughter Cards 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type M With 3 Cavities For Special Contacts 25 15 e d c b a 55-3 053792 55-3 103804 Type M With 3 Cavities For Special Contacts With Upper Shield With Peg 25 15 e d c b a Lower Shield For Type M 054354 Catalog E 07/10 Edition 1 www.erni.com 229 2.0 mm ERmet Hard Metric Connector System Verticale Male Connectors Type M for Backplanes 3 special and 55 signal contacts 50 mm with multifunction block The ERmet male connector type M provides a maximum of 77 contacts in 7 rows by 11 positions. The two outer rows, z and f are for the shielding contacts of the male connector, along with 3 contact positions for special power or coax contacts. This type contains a multifunction cavity for coding and pre-alignment in the center position. This connector is designed to be used alone or in conjunction with either a type B, C, L, or N ERmet connector. The type M male is available with a locating peg that helps secure the connector to the printed circuit board (PCB). Dimensional drawings and board hole pattern 15.4 date 230 2 13.45 2 10 x 2 = 20 4x2= 8 compliant zone for thru hole 0.6`0.00.05 25 15 z a b c d e f 1 max 3.75 max 50 max Board hole pattern (Component mounting side) all holes 10 x 2 = 0.1 0.6 plated thru drill hole 0.7 7.5 + 0.05 - all holes 7.5 0.1 6.1 min - not plated thru 5.9 +0.2 - plated thru 3.75 2 + 0.05 0.02 5.5 z a b c d e f 25 15 13 10 6 2 4.5 2 ( 12 ) 6.25 4 ( 20 ) 2 6x2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 3- 0.1 Id.-Nr. - 0.1 class Cavaties optional for an additioal fixation Board hole pattern (Component mounting side) for press-fitting 3.5 +- 0.04 0.06 plated thru 25 15 13 Catalog E 10 6 2 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Verticale Male Connectors Type M for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type M With 3 Cavities For Special Contacts 25 24 23 22 21 20 19 18 17 16 15 13 10 6 2 z a b 77-3 054087 55-3 064671 c d e f Type M With 3 Cavities For Special Contacts 25 24 23 22 21 20 19 18 17 16 15 13 10 6 2 z a b c d e f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. Catalog E 07/10 Edition 1 www.erni.com 231 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type N for Daughter Cards 3 cavities for special contacts 25 mm extension module The ERmet female connector type N is a connector housing with 3 contact positions for special power or coax contacts. The type N female is available with a locating and strain relief peg that helps secure the connector to the printed circuit board (PCB). Dimensional drawings and board hole pattern 2 * 7.5 = 15 7.5 max 3.75 max 232 3.7 12.8 - 0.2 20.65 - 0.2 3.7 + 0.05 - 25 max 1.6 11.4 12.25 Id.-Nr. date Board hole pattern ( Component mounting side ) for free wiring 5.25 7.5 all holes 7.5 0.1 2.5 2 + 0.1 not plated thru 2 2.5 2.5 2.5 3.5 6. 10 6 2 1.3 + 0.1 plated thru Board hole pattern ( Component mounting side ) for press - fitting 8 Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 4. 6.25 10 6 2 3.5 +- 0.04 0.06 plated thru Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Female Connectors Type N for Daughter Cards 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Type N With 3 Cavities For Special Contacts 044581 Catalog E 07/10 Edition 1 www.erni.com 233 2.0 mm ERmet Hard Metric Connector System Verticale Male Connectors Type N for Backplanes 3 cavities for special contacts 25 mm extension module The ERmet type N male connector is a connector housing with 3 contact positions for special coax or high power contacts. The type N male is available with a locating and strain relief peg that helps secure the connector to the printed circuit board (PCB). Dimensional drawings and board hole pattern 0.1 34.8 5.35 2 x 7.5 = 15 7.5 z 2 d f max 3.75 max 25 max Board hole pattern (Component mounting side) for free wiring 5.25 7.5 all holes 7.5 3.75 2 0.1 + 0.05 6.1 min not plated thru 5.9 + 0.2 plated thru 5.5 6.25 10 6 2 4.5 Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 234 - 0.1 15.4 Datum 13.45 Id.-Nr. Cavaties optional for an additional fixation Board hole pattern (Component mounting side) for press-fitting 3.5 -+ 0.04 0.06 plated thru 10 Catalog E 6 2 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Verticale Male Connectors Type N for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number 3 cavities for special contacts z 104147 d f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. Catalog E 07/10 Edition 1 www.erni.com 235 2.0 mm ERmet Hard Metric Connector System Shrouds Type A for Backplanes The ERmet shroud type A is possible for a maximum of 175 contacts in 7 rows by 25 positions. The two outer rows, z and f are for the shielding contacts of the female connector. This type contains a multifunction block for coding and prealignment which uses 3 positions. For CompactPCI applications the shroud type A is used on the position rP1 and rP4. Dimensional drawings 14.8 H 3.9 14.35 11.6 49.9 2 3.15 2 10 x 2 = Note: All dimensions in mm. H 236 20 8 6x2= 12 3.8 2 10 x 2 = 20 Ident-Nr. / Part No. 14.35 114436 14.95 054795 15.75 054794 16.55 054793 Catalog E Sammelzeichnung Combination Drawing 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Shrouds Type A for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For Type A Shroud 25 Positions rP1, rP4 114436 rP1, rP4 054795 rP1, rP4 054794 rP1, rP4 054793 Height 14.95 Type A Shroud 25 Positions Height 15.75 Type A Shroud 25 Positions 07/10 Part Number Height 14.35 Type A Shroud 25 Positions Catalog E No. of Pins Height 16.55 Edition 1 www.erni.com 237 2.0 mm ERmet Hard Metric Connector System Shrouds Type A for Backplanes Ordering Information Configuration Used For No. of Pins Part Number Height 14.35 Type A Shroud 19 Positions 124312 Type A Shroud 19 Positions Height 14.95 923109 Type A Shroud 19 Positions Height 15.75 923108 Type A Shroud 19 Positions Height 16.55 923107 238 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Shrouds Type B for Backplanes 2.0 mm ERmet The ERmetTM shroud type B is possible for a maximum of 175 contacts in 7 rows by 25 positions. The two outer rows, z and f are for the shielding contacts of the female connector. For this type , without multifuntion block for coding and pre-alignment, we recommend use only in combination with types A or C. Dimensional drawings 14.8 H 3.9 14.35 11.6 2 6x2= 12 49.9 2 24 x 2 = Note: All dimensions in mm. H Catalog E Ident-Nr. / Part No. 14.35 114437 14.95 054797 15.75 054798 16.55 054799 07/10 48 Edition 1 Sammelzeichnung Combination Drawing www.erni.com 239 2.0 mm ERmet Hard Metric Connector System Shrouds Type B for Backplanes Ordering Information Configuration Used For No. of Pins Part Number Height 14.35 Type B Shroud 25 Positions 114437 Type B Shroud 25 Positions Height 14.95 054797 Type B Shroud 25 Positions Height 15.75 054798 Type B Shroud 25 Positions Height 16.55 054799 240 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Shrouds Type B for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For No. of Pins Part Number Height 14.35 Type B Shroud 22 Positions a 114619 Type B Shroud 22 Positions Height 14.95 a 064692 Type B Shroud 22 Positions Height 15.75 a 064693 Type B Shroud 22 Positions Height 16.55 a 064694 Catalog E 07/10 Edition 1 www.erni.com 241 2.0 mm ERmet Hard Metric Connector System Shrouds Type B for Backplanes Ordering Information Configuration Used For Type B Shroud 19 Positions No. of Pins Part Number Height 14.35 a 114618 Type B Shroud 19 Positions Height 14.95 a 064622 Type B Shroud 19 Positions Height 15.75 a 064623 Type B Shroud 19 Positions Height 16.55 a 064624 242 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Shrouds Type C for Backplanes 2.0 mm ERmet The ERmet shroud type C is possible for a maximum of 77 contacts in 7 rows by 11 positions with the length of 25 mm. The two outer rows, z and f are for the shielding contacts of the female connector. Dimensional drawings 14.8 H 3.9 14.35 11.6 2 6x2= 12 24.55 2 10 x 2 = Note: All dimensions in mm. H Catalog E 07/10 20 Ident-Nr. / Part No. 14.35 114438 14.95 064172 15.75 064171 Sammelzeichnung 16.55 064170 Combination Drawing Edition 1 www.erni.com 243 2.0 mm ERmet Hard Metric Connector System Shrouds Type C for Backplanes Ordering Information Configuration Used For No. of Pins Part Number Height 14.35 Type C Shroud 11 Positions 114438 Type C Shroud 11 Positions Height 14.95 064172 Type C Shroud 11 Positions Height 15.75 064171 Type C Shroud 11 Positions Height 16.55 064170 244 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Shrouds Type AB for Backplanes 2.0 mm ERmet The ERmet shroud type AB is possible for a maximum of 169 contacts in 7 rows by 25 positions. The two outer rows, z and f are for the shielding contacts of the female connector. This type has pre-alignment flanges but no multifunction block for coding. The male shroud type AB, is also available in a smaller version for planned CompactPCI applications, it is used at the locations rP2 and rP5 with 154, respectively,110 contacts at 22 positions and on location rP3 with 133 respectively, 95 contacts at 19 positions. Dimensional drawings H 3.9 14.35 11.6 14.8 2 6x2= 15.4 12 43.9 2 21 x 2 = Note: All dimensions in mm. H Catalog E Ident-Nr. / Part No. 14.35 114425 14.95 114426 15.75 114427 16.55 114428 07/10 42 Edition 1 Sammelzeichnung Combination Drawing www.erni.com 245 2.0 mm ERmet Hard Metric Connector System Shrouds Type AB for Backplanes Ordering Information Configuration Used For No. of Pins Part Number Height 14.35 Type AB Shroud 25 Positions 114482 Type AB Shroud 25 Positions Height 14.95 114483 Type AB Shroud 25 Positions Height 15.75 114484 Type AB Shroud 25 Positions Height 16.55 114485 246 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Shrouds Type AB for Backplanes 2.0 mm ERmet Ordering Information Configuration Used For Type AB Shroud 22 Positions rP2, rP5 114425 rP2, rP5 114426 rP2, rP5 114427 rP2, rP5 114428 Height 14.95 Type AB Shroud 22 Positions Height 15.75 Type AB Shroud 22 Positions 07/10 Part Number Height 14.35 Type AB Shroud 22 Positions Catalog E No. of Pins Height 16.55 Edition 1 www.erni.com 247 2.0 mm ERmet Hard Metric Connector System Shrouds Type AB for Backplanes Ordering Information Configuration Used For Part Number Height 14.35 Type AB Shroud 19 Positions Type AB Shroud 19 Positions rP3 114487 rP3 114488 rP3 114489 rP3 114490 Height 14.95 Type AB Shroud 19 Positions Height 15.75 Type AB Shroud 19 Positions 248 No. of Pins Height 16.55 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Shrouds Type D for Backplanes 2.0 mm ERmet The ERmet shroud type D is possible for a maximum of 220 contacts in 10 rows by 25 positions with the length of 50 mm. The two outer rows, z and y are for the shielding contacts of the female connector. This type contains a multifunction block for coding and pre-alignment which uses 3 positions Dimensional drawings 20,8 14,35 3,9 H 17,6 49,9 10 x 2 = 20 8 10 x 2 = 20 2 2 9x2= 18 2 Note: All dimensions in mm. H Catalog E Ident-Nr. / Part No. 14.35 114467 14.95 114468 15.75 114469 16.55 114470 07/10 Edition 1 www.erni.com 249 2.0 mm ERmet Hard Metric Connector System Shrouds Type D for Backplanes Ordering Information Configuration Used For No. of Pins Part Number Height 14.35 Type D Shroud 25 Positions 114467 Type D Shroud 25 Positions Height 14.95 114468 Type D Shroud 25 Positions Height 15.75 114469 Type D Shroud 25 Positions Height 16.55 114470 250 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Shrouds Type E for Backplanes 2.0 mm ERmet The ERmet shroud type E is possible for a maximum of 220 contacts in 10 rows by 25 positions with the length of 50 mm. The two outer rows, z and y are for the shielding contacts of the female connector. For this type; without multifunction block for coding and pre-alignment, we recommend use only in combination with types D or F. Dimensional drawings 20,8 14,35 3,9 H 17,6 49,9 24 x 2 = 48 2 9x2= 18 2 Note: All dimensions in mm. H Catalog E Ident-Nr. / Part No. 14.35 114472 14.95 114473 15.75 114474 16.55 114475 07/10 Edition 1 www.erni.com 251 2.0 mm ERmet Hard Metric Connector System Shrouds Type E for Backplanes Ordering Information Configuration Used For No. of Pins Part Number Height 14.35 Type E Shroud 25 Positions 114472 Type E Shroud 25 Positions Height 14.95 114473 Type E Shroud 25 Positions Height 15.75 114474 Type E Shroud 25 Positions Height 16.55 114475 252 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Shrouds Type F for Backplanes 2.0 mm ERmet The ERmet shroud type F is possible for a maximum of 110 contacts in 10 rows by 11 positions with the length of 25 mm. The two outer rows, z and y are for the shielding contacts of the female connector. Dimensional drawings 20,8 14,35 3,9 H 17,6 24,55 10 x 2 = 20 2 9x2= 18 2 Note: All dimensions in mm. H Catalog E Ident-Nr. / Part No. 14.35 114477 14.95 114478 15.75 114479 16.55 114480 07/10 Edition 1 www.erni.com 253 2.0 mm ERmet Hard Metric Connector System Shrouds Type F for Backplanes Ordering Information Configuration Used For No. of Pins Part Number Height 14.35 Type F Shroud 11 Positions 114477 Type F Shroud 11 Positions Height 14.95 114478 Type F Shroud 11 Positions Height 15.75 114479 Type F Shroud 11 Positions Height 16.55 114480 254 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Female Monoblock Modules 2.0 mm ERmet 220 signal contacts 94 mm with multifunction block The ERmetTM female monoblock connector integrates the type A and the type B modules into one single piece. The monoblock provides a maximum of 220 contacts in 5 rows by 44 positions. The monoblock has integrated pre-centering and as an option integrated coding, acc. to PICMG Spec. for 3.3V or 5.0V, which requires 3 positions. For applications requiring the use of shielding, the female connector is supplied with a with an upper shield. Lower shield may be ordered separately. The monoblock has been designed especially for CompactPCI applications for the positions P1/P2 and for the positions P4/P5. The monoblock has a length of 94mm (3U) and can also be used for other applications in 19" rack systems. Dimensional drawings 47 1 e d 2 c b EE-Zone fur durchkontaktierte Locher O 0.6 0.05 4x2= 10 x 2 = 20 8 32 x 2 = Compliant zone for thru hole O 0.6 0.05 64 3 -0.4 Abschirmbleche - shieldings max. 2 1.7 0.05 94 XXXX ERNI 104732 2 10.8 -0.2 21 47 Catalog E 2 1 3 11.4 Id.-Nr. Anforderungsstufe Datum class Lochbild fur Leiterplatte (Bestuckungsseite) 10 x 2 = 0.1 0.6 alle Locher all holes 12.25 date ( 20 ) 8 Board hole pattern (Component mounting side) 32 x 2 = (64 ) 0.05 2 durchkontaktiert, Bohrloch 0.7 0.02 plated thru, drill hole 0.7 0.02 f d c 1.5 e b 1 2 ( 10) a 47 5x2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 8 a 2 07/10 Edition 1 www.erni.com 255 2.0 mm ERmet Hard Metric Connector System Right Angle Female Monoblock Modules Ordering Information Configuration Used For No. of Pins Part Number J4/J5 308 104732 J4/J5 308 104733 J4/J5 308 104734 Monoblock With Shield, Without Peg 47 1 e d c b a Monoblock With Shield, Without Peg, With Cadmium Yellow Coding Key 47 1 e d c b a Monoblock With Shield, Without Peg, With Brillant Blue Coding Key 47 1 e d c b a 256 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Vertical Male Monoblock Modules 2.0 mm ERmet 220 signal contacts 94 mm with multifunction block The ERmetTM vertical male monoblock connector integrates the type A and the type B in one single piece. The monoblock provides a maximum of 308 contacts in 7 rows by 44 positions. The two outer rows, z and f are for the shielding contacts of the female connector. The monoblock has integrated pre-centering and as option integrated coding acc. to PICMG Spec. for 3.3V or 5.0V, which requires 3 positions. The monoblock has been designed especially for CompactPCI applications. Available are versions with standard pin length for the positions P1 and P2 and versions with extended terminals for rear I/O for the positions P4 and P5. The monoblock has a length of 94mm (3U) and can also be used for other applications in 19" rack systems. Dimensional drawings 3 -0,1 2 2 2 10 x 2 = 20 8 32 x 2 = 13,45 -0,1 15,4 6x2= 64 12 EE Zone fuer durchkontaktierte Loecher O0.6 0.05 compliant zone for thru hole O 0.60.05 47 37 33 1 z a b c d e f 1 max 1 max 94 Lochbild fur Leiterplatte Bord hole pattern (Component mounting side) (Bestuckungsseite) 10 x 2 = 0,6 plated thru drill hole 0.7 0.02 max 4 (20 ) 4 32 x 2 = (64 ) +0,05 0,05 2 nicht durchkontaktiert 2 not plated thru durchkontaktiert Bohrloch 0.70.02 (12) z a 6x2= b c d e 2 Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 2 104735 ERNI Catalog E Datum date Id.-Nr. XXXX Anforderungsstufe class f 37 47 07/10 33 1 Edition 1 www.erni.com 257 2.0 mm ERmet Hard Metric Connector System Vertical Male Monoblock Modules Ordering Information Configuration Used For No. of Pins Part Number P1/P2 308 104735 P1/P2 308 104736 P1/P2 308 104737 P1 Per PICMG 2.0 R 2.1 P2 308 104765 P1 Per PICMG 2.0 R 2.1 P2 308 104766 Monoblock With Peg, With Shield 47 46 45 44 43 42 41 40 39 38 37 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Monoblock With Shield, Without Peg, With Cadmium Yellow Coding Key 47 46 45 44 43 42 41 40 39 38 37 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Monoblock With Shield, Without Peg, With Brillant Blue Coding Key 47 46 45 44 43 42 41 40 39 38 37 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Monoblock With Peg, With Shield And With Extended Terminals 47 46 45 44 43 42 41 40 39 38 37 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Monoblock With Peg, With Shield And With Extended Terminals 47 46 45 44 43 42 41 40 39 38 37 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. 258 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Dust Covers For Type A, B, AB, D, E and DE 2.0 mm ERmet The dust and protection cover for the male connectors for the ERmetTM 2.0 mm connector system acc. to IEC 610764-101 protect the mating area at the frontside of the backplane and what is more important the transfer area on the rearside of the backplane against damage of the contacts. They are also a protection for transportation and against dust. The dust and protection cover is available in two versions for type A, B, AB and for type D, E, DE with or without grip. Dimensional Drawings 49,94 12,45 14,8 11,6 Note: All dimensions in mm 11,15 Catalog E 07/10 Edition 1 www.erni.com 259 2.0 mm ERmet Hard Metric Connector System Dust Covers For Type A, B, AB, D, E and DE Ordering Information Configuration Used For No. of Pins Part Number A, B, AB Dust Cover Without Handle For Vacuum Pickup 104070 D, E, DE Dust Cover Without Handle For Vacuum Pickup 104939 A, B, AB Dust Cover With Handle For Hand Placement 114039 D, E, DE Dust Cover With Handle For Hand Placement 114040 260 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Coding Keys 2.0 mm ERmet Ordering Information Coding keys for male connectors and shrouds Coding keys for female connectors Coding Key Coding Key Catalog E Code Colour No. Part Number Code Colour No. Part Number Pastel Orange 3568 RAL 2003 Fincke 00233197 043342 Pastel Orange 1247 RAL 2003 Fincke 00233197 043332 Steel Blue 3478 RAL 5011 Fincke 00251197 043343 Steel Blue 1256 RAL 5011 Fincke 00251197 043333 Slate Grey 3467 RAL 7015 Fincke 00235197 043344 Slate Grey 1258 RAL 7015 Fincke 00235197 043334 Cadmium Yellow 3456 RAL 1021 Fincke 00252197 043345 Cadmium Yellow 1278 RAL 1021 Fincke 00252197 043335 Reseda Green 2578 RAL 6011 Fincke 00237197 043346 Reseda Green 1346 RAL 6011 Fincke 00237197 043336 Brilliant Blue 1567 RAL 5007 Fincke 00245197 043347 Brilliant Blue 2348 RAL 5007 Fincke 00245197 043337 Blue/Lilac 1356 RAL 4005 Fincke 00246197 043348 Blue/Lilac 2478 RAL 4005 Fincke 00246197 043338 Ocher Yellow 4678 RAL 1024 Fincke 00313197 043349 Ocher Yellow 1235 RAL 1024 Fincke 00313197 043339 Strawberry Red 1248 RAL 3018 Fincke 00312197 043350 Strawberry Red 3567 RAL 3018 Fincke 00312197 043340 Nut Brown 1236 RAL 8011 Fincke 00272197 043351 Nut Brown 4578 RAL 8011 Fincke 00272197 043341 Mounting Device For Coding-Keys 053593 07/10 Edition 1 www.erni.com 261 2.0 mm ERmet Hard Metric Connector System Guide Pin for ERmet 10 Row Type D The optional applicable guide pin for the 10 row ERmet type D connector made of stainless steel is suited for the secure pre-centering when mating. The guide pin will be screwed with the connector and the pcb after the male connector has been pressed-in. Ordering Information Description Guide Pin Toothed Lock Washer Hexagon Nut #2-56 UNC-2A Kit (Including Guide Pin, Toothed Lock Washer and Hexagon Nut) 262 Catalog E Part Number 104790 104788 104789 104791 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Special Contacts for Type L, M and N 2.0 mm ERmet Ordering Information For Coax Contacts Characteristic Impedance 50 Ohm 50 Ohm 50 Ohm 50 Ohm 50 Ohm 50 Ohm 50 Ohm 50 Ohm 50 Ohm 50 Ohm 75 Ohm 75 Ohm 75 Ohm Contact Version Male; Crimp-Version Female; Crimp-Version Male; PCB-Solder-Version; Right Angle Female; Crimp-Version Male; Crimp-Version Female; Crimp-Version Male; Press-Fit-Version; Right Angle Female; Crimp-Version Male; Crimp-Version Female; Press-Fit-Version R1 Male; PCB-Solder-Version; Right Angle Male; Crimp-Version Female; Crimp-Version Cable Type RG 178 B/U; RG 196 A/U RG 178 B/U; RG 196 A/U RG 316 Protected RG 316 Protected RG 174 /U; RG 188 A/U; RG 316 /U RG 174 /U; RG 188 A/U; RG 316 /U RG 174 /U; RG 188 A/U; RG 316 /U RG 179 B/U; RG 187 A/U RG 179 B/U; RG 187 A/U Part Number 013686 013687 053299 053395 053400 054238 104875 594207 594213 914382 053306 053408 053410 Ordering Information for High Power Contacts Max. Current 10 A 20 A 30 A 40 A 40 A 10 A 20 A 40 A 40 A 10 A 20 A 20 A 30 A 40 A 10 A 40 A 40 A 10 A 20 A 40 A 10 A Catalog E Contact Version Comments Female; Crimp-Version Female; Crimp-Version Female; Crimp-Version Female; Crimp-Version Female; Press-Fit-Version R3 Female; Solder-Version Female; Solder-Version Female; Solder-Version Female; Solder-Version; Right Angle Male; Crimp-Version Male; Crimp-Version First Made Last Break; Only Usable With Part No. 044965 Male; Crimp-Version Male; Crimp-Version Male; Crimp-Version Male; Press-Fit-Version R1 First Made Last Break Male; Press-Fit-Version R1 First Made Last Break; Only Usable With Part No. 044965 Male; Press-Fit-Version R1 Male; Solder- Version Male; Solder- Version Male; Solder- Version Male; Solder-Version First Made Last Break; Only Usable With Part No. 044965 07/10 Edition 1 www.erni.com Part Number 594178 594180 053452 594182 044965 594172 594174 594176 053298 594227 053430 594229 033319 594231 103855 044846 044847 594221 594223 594225 053444 2.0 mm ERmet Hard Metric Connector System Tools Modular press-fit tools for male and female connectors 264 Modular press-fit tool male connector modules 5+2 Modular press-fit tool for female connector modules 5+2 ERmet connectors can be end to end mounted in modular layout. To be able to press-fit the selected connector layout for your application in a rationalized way, we have designed the necessary press-fit tools to be modular too. This is true of the tools both for male connectors and for female connectors. The tool bases, also termed anvils, are fixed in a tool holder. Each connector module requires an appropriately sized tool module. The standard tool holders are designed for two 50 mm modules (modules A, B, L and M), press-fitting a total module length of 100 mm. Due to the modular tool configuration, press-fitting can be carried out in any order. Using filler elements, it is also possible to press-fit just individual modules. For details on how to order press-fit tools, please contact the factory. Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Tools 2.0 mm ERmet Press-In-Tools For The Female Connectors Ordering Information Design Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Female Vertical Fem. Vertical Fem. Vertical Fem. Vertical Fem. Vertical Fem. Vertical Fem. Vertical Fem. Vertical Fem. Catalog E Module A B/AB C L L M M M N N A B/AB C M M A A/AB C D E/DE F D E/DE F D E/DE F B19/AB19 B19/AB19 B19/AB19 B22/AB22 B22/AB22 B22/AB22 A B B19 B22 C D E F 07/10 Upper Tools 220006 220006 220007 220008 220008 220009 220009 220009 220010 220010 220093 220093 220096 220322 220322 220436 220436 220453 220253 220253 220254 220256 220256 220257 220455 220455 220457 220175 220179 220449 220183 220187 220451 220204 220204 220356 220357 220341 220477 220477 220478 Edition 1 Lower Tools 220020 220021 220022 220023 220402 220024 220323 220415 220025 220287 220020 220021 220022 220024 220323 220437 220437 220454 220250 220251 220252 220250 220251 220252 220458 220456 220458 220176 220176 220450 220184 220184 220452 220026 220027 220174 220182 220028 220247 220248 220249 www.erni.com Comments Standard Standard Standard Standard; High Power Contact, Press-fit Standard; Coax-Contact, Press-fit Standard; High Power Contact, Press-fit Standard; Coax-Contact, Press-fit Standard; Coax-Contact, Solder Standard; High Power Contact, Press-fit Standard; Coax-Contact, Press-fit Upper Shield Upper Shield Upper Shield Upper Shield ; High Power Contact, Press-fit Upper Shield ; Coax- Contact, Press-fit Lower Shield Lower Shield Lower Shield Standard Standard Standard Upper Shield Upper Shield Upper Shield Lower Shield Lower Shield Lower Shield VME/64 VME/64 Upper Shield VME/64 Lower Shield PCI PCI Upper Shield PCI Lower Shields Standard Standard VME/64 PCI Standard Standard Standard Standard 265 2.0 mm ERmet Hard Metric Connector System Tools Press-In-Tools For The Male Connectors Ordering Information Design Male Male Male Male Male Male Male Male Male Male Male Male Male Male Male Male Male Male Male Module A A B AB25 AB22 AB19 C L L M M N N B19 B22 D E F DE Upper Tools 220011 220469 220012 220376 220401 220400 220013 220014 220420 220015 220422 220016 220424 220173 220181 220244 220245 220246 220410 Lower Tool 220026 220026 220027 220182 220182 220174 220028 220029 220421 220030 220423 220031 220425 220174 220182 220247 220248 220249 220248 Comment Standard Standard; Integrated Coding Standard Standard Standard Standard Standard Standard; High Power Contact, Press-fit Standard; Coax-Contact, Press-fit Standard; High Power Contact, Press-fit Standard; Coax-Contact, Press-fit Standard; High Power Contact, Press-fit Standard; Coax-Contact, Press-fit VME/64 PCI Standard Standard Standard Standard Toolholder Ordering Information 266 Description Holder Upper Tool Holder Upper Tool Holder Upper Tool Holder Upper Tool Holder Upper Tool Holder Upper Tool Part Number 220001 220002 220188 220003 220004 220005 Length 100mm long 100 mm long 150 mm long 150 mm long 250 mm long 250 mm long Comment with monting pivot O 20 with quick change with monting pivot O 20 with quick change with monting pivot O20 with quick change Holder Lower Tool Holder Lower Tool Holder Lower Tool 220191 220267 220268 100 mm long 150 mm long 250 mm long for lowerable table for lowerable table for lowerable table Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System 3U CompactPCI(R) Daughter Card Layout 2.0 mm ERmet connectors from the bottom up. Manufacturers and users should note that the connectors themselves are labeled in accordance to IEC 61076-4-101 and prevailing industry practice from the top down. The 3U CompactPCI(R) backplane and daughter card layouts are provided to clarify the contact numbering and connector nomenclature used within the specification. As is typical of some telecommunication applications, the CompactPCI(R) specification numbers the signals and +0 160.0-0.3 3.57 1.5 0.1 0.1 5.55 2 J2 Part # 064 785 88.9+0.1 -0.1 TOP VIEW 2 J1 Part # 064 176 22 4.0 0.6 0.05 THRU PLATED (Rows A to F) 1 100.0 25 DRILLED TO 0.7 0.02 15 8 2.0 0.05 11 2 4.0 1 5.55 FEDCBA Note that the backplane and daughter card are numbered in accordance with the CompactPCI(R) specification. The numbering on the connectors themselves is different and in accordance with the IEC 61076-4-101 standard. All dimensions are in millimeters (mm) unless otherwise noted. Catalog E 07/10 Edition 1 www.erni.com 267 2.0 mm ERmet Hard Metric Connector System 3U CompactPCI(R) Backplane Layout nectors from the bottom up. Manufacturers and users should note that the connectors themselves are labeled in accordance to IEC 61076-4-101 and prevailing industry practice from the top down. The 3U CompactPCI(R) backplane layout is provided to clarify the contact numbering and connector nomenclature used within the specification. As is typical of some telecommunication applications, the CompactPCI(R) specification numbers the signals and con- 0.0 n x 20.32-0.3 0.00 9.16 -0.30 Non-Accumulative 20.32 10.16 15.250.03 1.55 0.1 2 Part # 914 796 22 2 P2 TOP VIEW 0.6 0.05 THRU PLATED (Rows Z to F) 1 25 128.70 +0.00 -0.30 2.0 0.05 Part # 064 097 DRILLED TO 0.7 0.02 8 122.500.03 P1 2 15 11 1 ZABCDEF ZABCDEF ZABCDEF Note that the backplane is numbered in accordance with the CompactPCI(R) specification. The numbering on the connectors themselves is different and in accordance with the IEC 61076-4-101 standard. All dimensions are in millimeters (mm) unless otherwise noted. 268 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System 6U CompactPCI(R) Daughter Card Layout 2.0 mm ERmet The 6U CompactPCI(R) backplane layout is provided to clarify the contact numbering and connector nomenclature used within the specification. As is typical of some telecommunication applications, the CompactPCI(R) specification numbers the signals and connectors from the bottom up. Manufacturers and users should note that the connectors themselves are labeled in accordance to IEC 61076-4-101 and prevailing industry practice from the top down. In many applications, the J3, J4 and J5 connectors are used for user I/O. The J3 connector matches the VME64 extensions P0 connector exactly and falls symmetrically on the centerline of the daughter card. Designers should note that this connector is not on the same grid as the J1, J2, J4 and J5 connectors. +0 160.0-0.3 2 0.1 3.57 4.0 J5 15 J4 11 2 1 19 TOP VIEW 2.675 233.35 +0 -0.3 CL J3 Part # 064 784 2.0 +0.05 -0.00 8 Part # 064 176 1 25 88.9 +0.1 -0.1 44.45 Part # 064 785 22 1 22 J2 Part # 064 785 J1 Part # 064 176 2.675 2 0.6 0.05 THRU PLATED (Rows A to F) 88.9+0.1 -0.1 1 25 DRILLED TO 0.7 0.02 2.0 +0.05 -0.00 15 8 11 2 4.0 FEDCBA 5.55 1.5 1 0.1 Note that the daughter card is numbered in accordance with the CompactPCI(R) specification. The numbering on the connectors themselves is different and in accordance with the IEC 61076-4-101 standard. All dimensions are in millimeters (mm) unless otherwise noted. Catalog E 07/10 Edition 1 www.erni.com 269 2.0 mm ERmet Hard Metric Connector System 6U CompactPCI(R) Backplane Layout The 6U CompactPCI(R) backplane layout is provided to clarify the contact numbering and connector nomenclature used within the specification. As is typical of some telecommunication applications, the CompactPCI(R) specification numbers the signals and connectors from the bottom up. Manufacturers and users should note that the connectors themselves are labeled in accordance to IEC 61076-4-101 and prevailing industry practice from the top down. In many applications, the P3, P4 and P5 connectors are designed for user I/O. Therefore connectors with 16 mm rear tails are used with shrouds installed on the rear side. The P3 connector matches the VME64 extensions J0 connector exactly, and falls symmetrically on the centerline of the backplane. Designers should note that this connector is not on the same grid as the P1, P2, P4 and P5 connectors. 0.0 n x 20.32-0.3 0.00 9.16 -0.30 20.32 Non-Accumulative 15.250.03 0.1 10.16 1.55 2 Part # 064 690 22 P5 2.0 0.05 Part # 914 793 2 CL 15 P4 11 1 19 2.675 TOP VIEW 8 Part # 064 688 1 25 255.85 P3 262.05 +0.0 -0.3 1 22 Part # 914 796 2 0.6 0.05 THRU PLATED (Rows Z to F) 2.675 P2 8 2.0 0.05 2 ZABCDEF ZABCDEF ZABCDEF ZABCDEF Part # 064 097 1 25 DRILLED TO 0.7 0.02 P1 ZABCDEF ZABCDEF 15 11 ZABCDEF ZABCDEF 1 3.10 Note that the backplane is numbered in accordance with the CompactPCI(R) specification. The numbering on the connectors themselves is different and in accordance with the IEC 61076-4-101 standard. All dimensions are in millimeters (mm) unless otherwise noted. 270 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System 9U 10-Row 2mm Daughter Card Layout 2.0 mm ERmet This 9U eurocard compatible daughtercard layout is provided for designers who need over 1400 signal pins in a eurocard format. This is one of the highest I/O densities that is currently available in a eurocard format. This design is to be used with the ERmet 8+2 row connectors. +0 160.0 -0.3 0.1 3.57 1.75 (Row H to I only) 1.5 5.55 J8 E22 4.0 Part # 933 052 Needs Shield 1 J7 15 D25 11 2 25 1 J6 E19 2.675 44.45 Part # 933 054 Needs Shield 2.0 +0.05 -0.00 8 Part # 104 415 22 1 88.9 +0.1 -0.1 2.675 E22 J5 0.6 0.05 22 1 11 J4 15 D25 TOP VIEW 2.0 +0.05 -0.00 8 2 25 1 J3 E19 J2 E22 Part # 933 052 Needs Shield D25 Part # 104 415 2.675 44.45 Part # 104 415 366.70 +0 -0.3 DRILLED TO 0.7 0.02 Part # 933 054 Needs Shield THRU PLATED (Rows A to Y) 88.9+0.1 -0.1 Part # 933 052 Needs Shield 19 1 2 11 1 2.675 2 0.6 0.05 THRU PLATED (Rows A to Y) 88.9+0.1 -0.1 22 1 DRILLED TO 0.7 0.02 2.0 +0.05 -0.00 11 8 15 J1 2 5.55 IHGFEDCBA 25 1.5 0.1 2mm 45 angle Note that the numbering scheme conforms with the Type V numbering as defined in VITA30-199x Draft 0.5 dated 9 June 1999 and is from the top down. This numbering scheme is identical to the numbering established for the connector within the IEC 61076-4-101 standard. Catalog E 07/10 Edition 1 www.erni.com 271 2.0 mm ERmet Hard Metric Connector System 9U 10-Row 2mm Backplane Layout used with the ERmet 8+2 row connectors. Note that the backplane connectors have a 5HP or 25.4 mm slot to slot spacing. This 9U eurocard compatible backplane layout is provided for designers who need over 1400 signal pins in a eurocard format. This is one of the highest I/O densities that is currently available in a eurocard format. This design is to be 80.28mm 0.00 9.16 -0.30 25.4 25.4 15.250.03 2 0.1 25.4 10.16 3.10 1.55 P8 Part # 933 048 1 P7 2.0 +0.05 -0.00 15 25 1 2.675 358.7 389.2 395.4 P6 Part # 933 049 11 8 Part # 104 152 22 1 2.675 P5 0.6 0.05 THRU PLATED (Rows Z to I) Part # 933 048 19 1 2 11 8 P4 2.0 +0.05 -0.00 15 Part # 104 152 22 1 DRILLED TO 0.7 0.02 2.675 P3 19 1 P2 Part # 933 048 P1 Part # 104 152 2.675 Part # 933 049 25 1 22 1 11 15 ZABCDEFGHI ZABCDEFGHI 25 15.250.03 3.10 Note that the numbering scheme conforms with the Type V numbering as defined in VITA30-199x Draft 0.5 dated 9 June 1999 and is from the top down. This numbering scheme is identical to the numbering established for the connector within the IEC 61076-4-101 standard. 272 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System IEEE 1301 Daughter Cards for IEC 61076-4-101 2mm HM Connectors 2.0 mm ERmet The 2mm HM Connector was originally developed to be used within subrack and backplanes designed in accordance with IEEE 1301 Standard for Metric Equipment Practices for Microcomputers. This was a standard that was popular with the large telecommunication companies. Although IEEE 1301 never became as popular as the IEEE 1101 line of Eurocard Packaging, engineers still may occasionally need to layout daughter cards and backplanes to this standard. Note that this layout is drawn to show both the connector grid for 5+2 row connectors and 8+2 row connectors. Ds - 15 4.0 +0 -0.15 5.0 5.0 2mm for 5+2 connectors (a - f rows) 1.5 0.1 7.5 FEDCBA 2.0 5 + 26 Connector6 Pattern USABLE COMPONENT SPACE 265 +0 -0.3 250 257 8 + 26 Connector6 Pattern 2.0 I H G F E DC B A 5.0 1.5mm for 8+2 connectors (1.75mm for H to I) DRILLED TO 2.75 +0.2 -0.0 Catalog E 07/10 Edition 1 www.erni.com 7.5 273 2.0 mm ERmet Hard Metric Connector System IEEE 1301 Backplane Layouts For IEC 61076-4-101 2mm HM Connectors The 2mm HM Connector was originally developed to be used within subrack and backplanes designed in accordance with IEEE 1301 Standard for Metric Equipment Practices for Microcomputers. This was a standard that was popular with the large telecommunication companies. Although IEEE 1301 never became as popular as the IEEE 1101 line of Eurocard Packaging, engineers still may occasionally need to layout daughter cards and backplanes to this standard. Note that this layout is drawn to show both the connector grid for 8+2 connectors and 5+2 row connectors. Although this standard defines multiple heights, this drawing is for the popular 12 SU height. 20.00 2.5 5.0 5.0 typical ZABCDEF ZABCDEF ZABCDEF DRILLED TO 2.75 +0.2 -0.0 ZABCDEF 5+ 2 250.00 295.00 285.00 8+ 2 ZABCDEFGHI ZABCDEFGHI ZABCDEFGHI 5.0 ZABCDEFGHI 5.0 typical DRILLED TO 2.75 +0.2 -0.0 2.5 25.00 274 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System VME64 Extensions Daughter Card 2.0 mm ERmet in between the upper P1 and lower P2 connectors. This connector is mounted 1.5 mm from the rear board edge but the 160 pin VME64x connector is mounted 2.76 mm from the rear board edge. The 6U VME64 Extensions document, IEEE 1101.10 defines the daughter card locations for a 2mm HM P0 connector. This connector is the same connector defined as the J3 connector defined in the VITA 30 2mm equipment practice and used for CompactPCI daughter cards. Note that the 2mm HM connector is located symmetrically +0 160.0-0.3 3.57 2.76 153.67 2.5 1 88.9 +0.1 -0.1 CL P1 88.9 +0.1 -0.1 16 17 32 1 133.35 +0.1 -0.1 OPTIONAL P0 USABLE COMPONENT SPACE 1.5 233.35 +0 -0.3 19 FEDCBA 1 88.9+0.1 -0.1 CL P2 88.9+0.1 -0.1 16 17 50.0 +0.1 -0.1 32 5.5 DRILLED TO 2.7 0.01 D C B A Z DRILLED TO 2.8 0.01 2.5 Note that the numbering of the P0 connector conforms to IEEE 1101.1 and 1101.10 and is from the top down. This also is the same numbering scheme established by the connector standard IEC 61076-4-101. Catalog E 07/10 Edition 1 www.erni.com 275 2.0 mm ERmet Hard Metric Connector System VME64 Extensions Backplane The 6U VME64 Extensions backplane layout depicts the nomenclature and numbering conventions used in the IEEE 1101.10 draft standard. The J0 center connector is the same 19 position ERmet 2mm H. M. connector used in CompactPCI(R). The design of this connector allows it to mate properly with the J1 and J2 connectors which are in accordance with 0.0 n x 20.32-0.3 0.00 9.16 -0.30 DIN 41612. Note that there is a 1.85 mm offset between the "C" row of the J0 connector and the "B" row of the 2.54 mm (.100") J1/J2 connectors. On the daughter card, pin 10 of the P0 connector falls exactly on the board's centerline, and pin "A 1" is placed 1.5 mm from the board's edge. 10.16 20.32 Non-Accumulative 16.25 Z A B C D Z A B C D Z A B C D Z A B C D Z A B C D Z A B C D Z A B C D Z A B C D a1 2 4 6 8 0.3 10 a1 2 12 14 900.1 16 J1 Z 18 A B C D 20 22 24 26 28 30 9.305 32 J0 43.35 ZABCDEF ZABCDEF ZABCDEF ZABCDEF ZABCDEF ZABCDEF Part # 914 793 CL 1 255.85 262.05 +0.0 -0.3 ZABCDEF ZABCDEF 19 1.85 Z A B C D E F a1 2 4 6 9.305 19 1.85 8 a1 2 10 12 14 90 0.1 J2 Z 16 18 A B C D 4 20 22 24 26 28 30 32 2.54 16.25 Drilled To 1.15 0.02 +0.09 Plated To 1.0 -0.06 0.3 2.54 Note that the numbering of the P0 connector conforms to IEEE 1101.1 and 1101.10 and is from the top down. This also is the same numbering scheme established by the connector standard IEC 61076-4-101. 276 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System 64 Bit CompactPCI(R) System Slot Pin Assignments PIN A B C D E 22 GND GA4(6) GA3(6) GA2(6) GA1(6) GA0(6) GND 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3(3) 2(3) 1(3) GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND CLK6 CLK5 GND BRSVP2A18 BRSVP2A17 BRSVP2A16 BRSVP2A15 AD[35] AD[38] AD[42] AD[45] AD[49] AD[52] AD[56] AD[59] AD[63] C/BE[5]# V(I/O)(3) CLK4 CLK2 CLK1 GND GND GND BRSVP2B18 GND BRSVP2B16 GND AD[34] GND AD[41] GND AD[48] GND AD[55] GND AD[62] GND BRSVP2B4 GND CLK3 GND RSV RSV RSV(9) BRSVP2C18 PRST# DEG# FAL# AD[33] V(I/O)(3) AD[40] V(I/O)(3) AD[47] V(I/O)(3) AD[54] V(I/O)(3) AD[61] V(I/O)(3) C/BE[7]# GNT3# SYSEN#(4) REQ1# RSV GND RSV(9) GND(8) REQ6# GND REQ5# GND AD[37] GND AD[44] GND AD[51] GND AD[58] GND C/BE[4]# GND REQ4# GNT2# GNT1# RSV RSV RSV(9) BRSVP2E18 GNT6# BRSVP2E16 GNT5# AD[32] AD[36] AD[39] AD[43] AD[46] AD[50] AD[53] AD[57] AD[60] PAR64 C/BE[6]# GNT4# REQ3# REQ2# GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND 25 24 23 22 21 20 19 18 17 16 15 12-14 11 10 9 8 7 6 5 4 3 2 1 PIN GND GND GND GND GND GND GND GND GND GND GND 5V AD[1] 3.3V AD[7] 3.3V AD[12] 3.3V SERR# 3.3V DEVSEL# 3.3V REQ64# 5V AD[4] GND AD[9] GND AD[15] GND IPMBSCL GND FRAME# 3.3V AD[0] 5V(1) AD[6] M66EN (5) AD[11] GND(1) PAR GND(1) STOP# GND(2) 5V ACK64# AD[2] AD[5] C/BE[0]# AD[10] AD[13] C/BE[1]# PERR# LOCK# TRDY# GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND Z(10) AD[18] AD[21] C/BE[3]# AD[26] AD[30] REQ0# BRSVP1A5 IPMB PWR INTA# TCK(8) 5V A AD[17] GND GND(2) GND AD[29] GND BRSVP1B5 HEALTHY#(7) INTB# 5V -12V B ENUM# V(I/O)(3) (1) AD[3] 3.3V(1) AD[8] V(I/O)(3) AD[14] 3.3V IPMBSDA V(I/O)(1),(3) IRDY# KEY AREA AD[16] 3.3V AD[23] V(I/O)(3) AD[28] 3.3V(1) RST# V(I/O)(3)(1) INTC# TMS(8) TRST#(8) C GND(1) AD[20] GND(1) AD[25] GND(1) CLK0 GND(1) INTP 5V(1) TDO(8) +12V D C/BE[2]# AD[19] AD[22] AD[24] AD[27] AD[31] GNT0# INTS INTD# TDI(8) 5V E GND GND GND GND GND GND GND GND GND GND GND F Z(10) 2.0 mm ERmet 3U cards, 6U implementations provide optional P3, P4 and P5 connectors, which all have undefined pins for user I/O. 6U CompactPCI(R) provides more user defined pins than any other bus structure today. In the case of the 64 bit CompactPCI(R), both the P1 and P2 connectors are fully assigned with no pins available for user defined I/O. For such systems, only 6U designs can have rear panel I/O. Although CompactPCI(R) is designed to be accomplished on F P2 C O N N E C T O R P1 C O N N E C T O R Per CompactPCI(R) Specification 2.0 R3.0, October 1, 1999, Tabelle 15 (1) Early mate pins. (2) Late mate pins. (3) 3.3 V or 5.0 V. (4) Grounded in system slot. (5) Ground for a 33 MHz backplane. Bussed slot to slot in 66 MHz systems. (6) Each slot may have a unique geographic address encoding. See the CompactPCI(R) specification for details. (7) Backplane must leave pin open and provide # bypass capacitor. (8) JTAG is being discouraged. These pins will be redefined. (9) To be used for I2C bus. (10) Daughtercards do not make use of "z" row grounds. Note: Chart numbering conforms to the CompactPCI(R) specification. Connector numbering is from top to bottom in accordance with the IEC standard. Catalog E 07/10 Edition 1 www.erni.com 277 2.0 mm ERmet Hard Metric Connector System 64 Bit CompactPCI(R) Peripheral Slot Pin Assignments on 3U cards, 6U implementations provide optional P3, P4 and P5 connectors, which all have undefined pins for user I/O. 6U CompactPCI(R) provides more user defined pins than any other bus structure today. In the case of the 64 bit CompactPCI(R), both the P1 and P2 connectors are fully assigned with no pins available for user defined I/O. For such systems, only 6U designs can have rear panel I/O. Although CompactPCI(R) is designed to be accomplished PIN Z(10) A B C D E F 22 GND GA4(6) GA3(6) GA2(6) GA1(6) GA0(6) GND 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3(3) 2(3) 1(3) GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND RSV RSV RSV BRSVP2A18 BRSVP2A17 BRSVP2A16 BRSVP2A15 AD[35] AD[38] AD[42] AD[45] AD[49] AD[52] AD[56] AD[59] AD[63] C/BE[5]# V(I/O)(3) RSV RSV RSV RSV RSV RSV BRSVP2B18 GND BRSVP2B16 GND AD[34] GND AD[41] GND AD[48] GND AD[55] GND AD[62] GND BRSVP2B4 GND RSV GND RSV RSV RSV BRSVP2C18 RSV RSV RSV AD[33] V(I/O)(3) AD[40] V(I/O)(3) AD[47] V(I/O)(3) AD[54] V(I/O)(3) AD[61] V(I/O)(3) C/BE[7]# RSV UNC(4) RSV RSV GND RSV GND RSV GND(8) RSV GND AD[37] GND AD[44] GND AD[51] GND AD[58] GND C/BE[4]# GND RSV RSV RSV RSV RSV RSV BRSVP2E18 RSV BRSVP2E16 RSV AD[32] AD[36] AD[39] AD[43] AD[46] AD[50] AD[53] AD[57] AD[60] PAR64 C/BE[6]# RSV RSV RSV GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND 25 24 23 22 21 20 19 18 17 16 15 12-14 11 10 9 8 7 6 5 4 3 2 1 PIN GND GND GND GND GND GND GND GND GND GND GND 5V AD[1] 3.3V AD[7] 3.3V AD[12] 3.3V SERR# 3.3V DEVSEL# 3.3V REQ64# 5V AD[4] GND AD[9] GND AD[15] GND IPMBSCL GND FRAME# 3.3V AD[0] 5V(1) AD[6] M66EN(4) (5) AD[11] GND(1) PAR GND(1) STOP# BD SEL#(2) 5V ACK64# AD[2] AD[5] C/BE[0]# AD[10] AD[13] C/BE[1]# PERR# LOCK# TRDY# GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND Z(10) AD[18] AD[21] C/BE[3]# AD[26] AD[30] REQ# BRSVP1A5 IPMB PWR INTA# TCK(8) 5V A AD[17] GND IDSEL(2) GND AD[29] GND BRSVP1B5 HEALTHY(7) INTB# 5V -12V B ENUM# V(I/O)(3) (1) AD[3] 3.3V(1) AD[8] V(I/O)(3) AD[14] 3.3V IPMBSDA V(I/O)(3) IRDY# KEY AREA AD[16] 3.3V AD[23] V(I/O)(3) AD[28] 3.3V(1) RST# V(I/O)(3) (1) INTC# TMS(8) TRST#(8) C GND(1) AD[20] GND(1) AD[25] GND(1) CLK GND(1) INTP 5V(1) TDO(8) +12V D C/BE[2]# AD[19] AD[22] AD[24] AD[27] AD[31] GNT# INTS INTD# TDI(8) 5V E GND GND GND GND GND GND GND GND GND GND GND F P2 C O N N E C T O R P1 C O N N E C T O R Per CompactPCI(R) Specification 2.0 R3.0, October 1, 1999, Tabelle 13 (1) Early mate pins. (2) Late mate pins. (3) 3.3 V or 5.0 V. (4) Grounded in system slot. (5) Ground for a 33 MHz backplane. Bussed slot to slot in 66 MHz systems. (6) Each slot may have a unique geographic address encoding. See the CompactPCI(R) specification for details. (7) Backplane must leave pin open and provide # bypass capacitor. (8) JTAG is being discouraged. These pins will be redefined. (9) To be used for I2C bus. (10) Daughtercards do not make use of "z" row grounds. Note: Chart numbering conforms to the CompactPCI(R) specification. Connector numbering is from top to bottom in accordance with the IEC standard. 278 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System 32 Bit CompactPCI(R) System Slot Pin Assignments 2.0 mm ERmet The CompactPCI(R) specification defines a 32 bit implementation. The 32 bit implementation makes the entire P2/J2 connector (upper) available for user defined I/O for slots 28. The controller card slot (usually slot 1) makes use of some P2 pins for such functions as clock, arbitration, grant/requests and some other system functions. In many 32 bit systems, the backplane connector in the P2 position will have 16 mm rear tails and a shroud so I/O signals may pass through the backplane to rear mounted cards or cable assemblies. PIN 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Z(6) GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND A GA4(5) CLK6# CLK5# GND BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) V(I/O) CLK4 CLK2 CLK1 B GA3(5) GND GND GND BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) GND CLK3 GND C GA2(5) BP(I/O) BP(I/O) BP(I/O)(9) BP(I/O) PRST# DEG# FAL# BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) GNT3# SYSEN# (10) REQ1# D GA1(5) BP(I/O) BP(I/O) BP(I/O)(9) BP(I/O) REQ6# GND REQ5# BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) REQ4# GNT2# GNT1# E GA0(5) BP(I/O) BP(I/O) BP(I/O)(9) BP(I/O) GNT6# BP(I/O) GNT5# BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) GNT4# REQ3# REQ2# F GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND 25 24 23 22 21 20 19 18 17 16 15 12-14 11 10 9 8 7 6 5 4 3 2 1 PIN GND GND GND GND GND GND GND GND GND GND GND 5V AD[1] 3.3V AD[7] 3.3V AD[12] 3.3V SERR# 3.3V DEVSEL 3.3v REQ64# 5V AD[4] GND AD[9] GND AD[15] GND IPMBSCL GND FRAME# 3.3V AD[0] 5V(1) AD[6] M66EN(4) AD[11] GND(1) PAR GND(1) STOP# GND(2) 5V ACK64# AD[2] AD[5] C/BE[0]# AD[10] AD[13] C/BE[1]# PERR# LOCK# TRDY# GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND Z(6) AD[18] AD[21] C/BE[3]# AD[26] AD[30] REQ0# BRSVP1A5 IPMB PWR INTA# TCK(8) 5V A AD[17] GND GND(2) GND AD[29] GND BRSVP1B5 HEALTHY#(7) INTB# 5V -12V B ENUM# V(I/O)(3) (1) AD[3] 3.3V(1) AD[8] V(I/O)(3) AD[14] 3.3V IPMBSDA V(I/O)(1),(3) IRDY KEY AREA AD[16] 3.3V AD[23] V(I/O)(3) AD[28] 3.3V(1) RST# V(I/O)(3) (1) INTC# TMS(8) TRST#(8) C GND(1) AD[20] GND(1) AD[25] GND(1) CLK GND(1) INTP 5V(1) TDO(8) +12V D C/BE[2]# AD[19] AD[22] AD[24] AD[27] AD[31] GNT0# INTS INTD# TDI(8) 5V E GND GND GND GND GND GND GND GND GND GND GND F P2 C O N N E C T O R P1 C O N N E C T O R Per CompactPCI(R) Specification 2.0 R3.0, October 1, 1999, Tabelle 16 (1) Early mate pins. (2) Late mate pins. (3) 3.3 V or 5.0 V. (4) Grounded in 33 MHz backplane. Bussed slot to slot in 66 MHz systems (5) Each slot may have a unique geographic address encoding. See the CompactPCI(R) specification for details. (6) Daughter cards do not make use of the "Z" row grounds. (7) Backplane must leave pin open and provide # bypass capacitor. (8) JTAG is being discouraged. These pins will be redefined. (9) To be used for I2C bus. (10) Grounded in system slot. Notes: All P2 terminals should be 16 mm long with shroud installed unless they are used for a secondary bus. Chart numbering conforms to the CompactPCI(R) specification. Connector numbering is from top to bottom in accordance with the IEC standard. Catalog E 07/10 Edition 1 www.erni.com 279 2.0 mm ERmet Hard Metric Connector System 32 Bit CompactPCI(R) Peripheral Slot Pin Assignments grant/requests and some other system functions. In many 32 bit systems, the backplane connector in the P2 position will have 16 mm rear tails and a shroud so I/O signals may pass through the backplane to rear mounted cards or cable assemblies. The CompactPCI(R) specification defines a 32 bit implementation. The 32 bit implementation makes the entire P2/J2 connector (upper) available for user defined I/O for slots 2-8. The controller card slot (usually slot 1) makes use of some P2 pins for such functions as clock, arbitration, PIN 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Z(6) GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND A GA4(5) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) B GA3(5) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) C GA2(5) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) D GA1(5) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) E GA0(5) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) BP(I/O) F GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND 25 24 23 22 21 20 19 18 17 16 15 12-14 11 10 9 8 7 6 5 4 3 2 1 PIN GND GND GND GND GND GND GND GND GND GND GND 5V AD[1] 3.3V AD[7] 3.3V AD[12] 3.3V SERR# 3.3V DEVSEL 3.3v REQ64# 5V AD[4] GND AD[9] GND AD[15] GND IPMBSCL GND FRAME# 3.3V AD[0] 5V(1) AD[6] M66EN(4) AD[11] GND(1) PAR GND(1) STOP# BD SEL#(2) 5V ACK64# AD[2] AD[5] C/BE[0]# AD[10] AD[13] C/BE[1]# PERR# LOCK# TRDY# GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND Z(6) AD[18] AD[21] C/BE[3]# AD[26] AD[30] REQ# BRSVP1A5 IPMB PWR INTA# TCK(8) 5V A AD[17] GND IDSEL(2) GND AD[29] GND BRSVP1B5 HEALTHY#(7) INTB# 5V -12V B ENUM# V(I/O)(3) (1) AD[3] 3.3V(1) AD[8] V(I/O)(3) AD[14] 3.3V IPMBSDA V(I/O)(1),(3) IRDY KEY AREA AD[16] 3.3V AD[23] V(I/O)(3) AD[28] 3.3V(1) RST# V(I/O)(3) (1) INTC# TMS(8) TRST#(8) C GND(1) AD[20] GND(1) AD[25] GND(1) CLK GND(1) INTP 5V(1) TDO(8) +12V D C/BE[2]# AD[19] AD[22] AD[24] AD[27] AD[31] GNT# INTS INTD# TDI(8) 5V E GND GND GND GND GND GND GND GND GND GND GND F P2 C O N N E C T O R P1 C O N N E C T O R Per CompactPCI(R) Specification 2.0 R3.0, October 1, 1999, Tabelle 14 (1) Early mate pins. (2) Late mate pins. (3) 3.3 V or 5.0 V. (4) Grounded in 33 MHz backplane. Bussed slot to slot in 66 MHz systems (5) Each slot may have a unique geographic address encoding. See the CompactPCI(R) specification for details. (6) Daughter cards do not make use of the "Z" row grounds. (7) Backplane must leave pin open and provide # bypass capacitor. (8) JTAG is being discouraged. These pins will be redefined. Notes: All P2 terminals should be 16 mm long with shroud installed unless they are used for a secondary bus. Chart numbering conforms to the CompactPCI(R) specification. Connector numbering is from top to bottom in accordance with the IEC standard. 280 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System cPCI Computer Telephony P4 Pin Assignments 2.0 mm ERmet Mechanical Specifications - Backplane and Chassis Pos# 25 24 23 22 21 20 19 18 17 16 15 12-14 11 10 9 8 7 6 5 4 3 2 1 Row Z NP NP NP NP NP NP NP NP NP NP NP Row A SGA4 GA4 +12V PFSO# -SELbat NP NP VRG NP NP -VBAT L NP NP NP NP NP NP NP NP NP NP NP CT_D29 CT_D27 CT_D24 CT_D21 CT_D19 CT_D16 CT_D13 CT_D11 CT_D8 CT_D4 CT_D0 M M M M M M M M M M M M M M M L M Row B Row C Row D SGA3 M SGA2 M SGA1 M GA3 M GA2 M GA1 M /CT_Reset M /CT_EN S -12v M RSVD M RSVD M RSVD M PFS1# M RSVD M RSVD M NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP KEY AREA (keep unobstructed on backplane to ease routing constraints) CT_D30 M CT_D31 M V(I/O) L +3.3V M CT_D28 M +5V L CR_D25 M CT_D26 M GND L CT_D22 M CT_D23 M +5V L +5V M CT_D20 M GND L CT_C17 M CT_D18 M GND L CT_D14 M CT_D15 M +3.3V L +5V M CT_D12 M +3.3V L CT_D9 M CT_D10 M GND L CT_D5 M CT_D6 M CT_D7 M +3.3V M CTP_D1 M CT_D2 M Row E SGA0 GAO CT_MC RSVD SELVbatRtN NP NP VRGTN NP NP VBATRTN /CT_FRAME_A /CT_FRAME_B /FR_COMP CT_C8_A CT_C8_B CT_NETREF_1 CT_NETREF_2 SCLK SCLK-D GND CT_D3 L Row F FG FG FG FG FG NP NP NP NP NP NP M M M M M M M M M L M GND GND GND GND GND GND GND GND GMD GND GND M M M M L M L L L L L L L L L L L L L L L L Per CompactPCI(R) Specification PICMG 2.5 R1.0, April 3, 1998, Table 1 Key to P4 Pin Assignments Ct_name +5V +3.3V GND V(I/O) FG RSVD NP -SELVbat SELVbatRtn -Vbat VbatRtn SGA0-SGA4 GA0-GA4 VRG VRGRtn PFS0#-PFS1# KEY AREA S M L Catalog E = H.110 TDM bus signals = +5V power = +3.3V power = LOGIC GROUND = I/O cell power = Frame Ground = reserved for future use = a pin and pad to Not be Populated = short loop battery = short loop battery return = telecom power distribution bus = return bus pin for -Vbat = shelf enumeration bus signals = slot ID signals; not bussed = bus for ringing voltage = bus for ringing voltage = busses for power fail sense = area utilized for key = Short (Level 1) front side pins = Medium (Level 2) front side pins = Long (Level 3) front side pins 07/10 Edition 1 www.erni.com 281 2.0 mm ERmet Hard Metric Connector System cPCI Computer Telephony Safety Classifications for J4/P4 Pos# 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 Row Z NP NP NP NP NP NP NP NP NP NP NP Row A NP NP NP NP NP NP NP NP HAZ NP NP NP HAZ NP NP NP NP NP NP NP NP IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C Row B NP IN/C IN/C IN/C IN/C NP NP IN/C-NP NP NP IN/C-NP Row C IN/C IN/C IN/C SELV IN/C IN/C NP NP IN/C-NP NP NP IN/C-NP Row D IN/C IN/C IN/C IN/C IN/C NP NP IN/C-NP NP NP IN/C-NP S S S S S Row E IN/C IN/C IN/C IN/C IN/C NP NP NP HAZ NP NP NP HAZ Row F GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C NP NP NP NP NP NP IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C GND-INC GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C KEY AREA (keep unobstructed on backplane to ease routing constraints) IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C SELV IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IIN/C S S S S S S S S L L L L L L L L Per CompactPCI(R) Computer Telephony Specification PICMG 2.5 R1.0, April 3, 1998, Table 11 282 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERme Hard Metric Connector System cPCI Computer Telephony P5 Pin Assignments Row Z NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C Np-IN/C NP-In/C NP-IN/C NP-In/C U U U U U U U U U U U U U U U U U U U U U Row A T1 R1 T2 R2 T3 R3 T4 R4 R5 T6 R6 T7 R7 T8 R8 IN/C IN/C Uo0 Ui0 Uo2 Ui2 S S S S S S S S S S S S S S S S S M M M M Row B T9 R9 T10 R10 T11 R11 T12 R12 R13 T14 R14 T15 R15 T16 R16 IN/C IN/C Uo1 Ui1 Uo3 Ui3 S S S S S S S S S S S S S S S S S M M M M Row C T17 R17 T18 R18 T19 R19 T20 R20 R21 T22 R22 T23 R23 T24 R24 IN/C IN/C GND_Ft Uo4 Ui4 +5V_FT S S S S S S S S S S S S S S S S S M M M M Row D T25 R25 T26 R26 T27 R27 T28 R28 R29 T30 R30 T31 R31 T32 R32 IN/C IN/C GND_Ft Uo5 Ui5 +12V_FT S S S S S S S S S S S S S S S S S M M M M Row E IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C GND_Ft Uo6 Ui6 -12V_FT S S S S S S S S S S S S S S S S S M M M M Row F GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-INC GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C 2.0 mm ERmet Pos# 22 21 20 19 18 17 16 15 13 12 11 10 9 8 7 6 5 4 3 2 1 L L L L L L L L L L L L L L L L L L L L L Per CompactPCI(R) Computer Telephony Specification PICMG 2.5 R1.0, April 3, 1998, Table 3 Key to P5 Pin Assignments Tn Rn IN/C NP NP-IN/C GND-IN/C +nV_FT -nV_FT GND_FT Uin Uon U Catalog E = Tip = Ring = No Connect required for safety agency Insulation requirements = a position required to be Not Populated (i.e., no conductive element present = a position which may be either Not Populated or Insulation No Connect = a position which may be either LOGIC GROUND or Insulation No Connect = positive supply voltage feed-through from CT Front Card = negative supply voltage feed-through from CT Front Card = logic ground feed-through from CT Front Card = Universal Input - user defined input signal (input to CT Front Card) = Universal Output - user defined input signal (output to CT Front Card) = a pin of unspecified length 07/10 Edition 1 S M L = Short (Level 1) front side pins = Medium (Level 2) front side pins = Long (Level 3) front side pins 2.3.2.1. P5 Telephony I/O Pins Tn - Tip - short (Level 1) pins for connecting to the nominally positive side of a balanced pair telephony connection Rn - Ring - short (Level 1) pins for connecting to the nominally negative side of a balanced pair telephony connection www.erni.com 283 2.0 mm ERmet Hard Metric Connector System cPCI Computer Telephony Safety Classifications for J5/P5 Pos# 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Row Z NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C NP-IN/C Np-IN/C NP-In/C NP-IN/C NP-In/C Row A IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C Row B Row C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C TNV3-SELV IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/CT Row D IN/C IN/C IN/C IN/C IN/C IN/C IN/C TNV1IN/C IN/C SELV IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IIN/C SELVIN/C IN/C IN/C S S S S S S S S S S S S S S S S S S S S S S Row E IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C IN/C Row F GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C SELV GND-INC GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C GND-IN/C L L L L L L L L L L L L L L L L L L L L L L Per CompactPCI(R) Computer Telephony Specification PICMG 2.5 R1.0, April 3, 1998, Table 12 284 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System PXI Generic Peripheral Slot Pinout Row F GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND Row E PXI_RSVA22 PXI_LBRO PXI_LBL4 PXI_LBL2 PXI_TRIG3 PXI_TRIG2 PXI_TRIG1 PXI_BRSVA15 AD[35] AD[38] AD[42] AD[45] AD[49] AD[52] AD[56] AD[59] AD[63] C/BE[5]# V[I/0] PXI_LBR7 PXI_LBR11 PXI_LBL9 5V AD[1] 3.3V AD[7] 3.3V AD[12] 3.3V SERR# 3.3V DEVSEL# 3.3V Row D PXI_RSVB22 GND PXI_LBR5 GND PXI_TRIG4 GND PXI_TRIGO GND AD[34] GND AD[41] GND AD[48] GND AD[55] GND AD[62] GND PXI_BRSVB4 GND PXI_LBR12 GND REQ64# 5V AD[4] GND AD[9] GND AD[15] GND SDONE GND FRAME# Row B PXI_RSVD22 PXI_LBR2 GND PXI_LBL4 GND PXI_STAR GND PXI_LBL6 GND AD[37] GND AD[44] GND AD[51] GND AD[58] GND C/BE[4]# GND PXI_LBR9 PXI_LBL7 PXI_LBL11 3.3V AD[0] 5V AD[6] M66EN AD[11] GND PAR GND STOP# GND Row A PXI_RSVE22 PXI_LBR3 PXI_LBL1 PXI_LBL5 PXI_TRIG6 PXI_CLK10 PXI_TRIG7 PXI-LBR6 AD[32] AD[36] AD[39] AD[43] AD[46] AD[50] AD[53] AD[57] AD[60] PAR64 C/BE [6]# PXI_LBR10 PXI_LBL8 PXI_LBL12 5V ACK64# AD[2] AD[5] C/BE[0]# AD[10] AD[13] C/BE[1]# PERR# LOCK# TRDY# PMC Slot GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND AD[17] GND IDSEL GND AD[29] GND BRSVP1B5 GND INTB# 5V -12V Row C PXI_RSVC22 PXI_LBR1 PXI_LBLO PXI_LBL3 PXI_TRIG5 PRST# DEG# FAL# AD[33] V(I/0) AD[40] V[I/0] AD[47] V[I/0] AD[54] V[I/0] AD[61] V[I/0] C/BE[7]# PXI_LBR8 SYSEN# PXI_LBL10 ENUM# V[1/0] AD93] 3.3V AD[8] V[1/0] AD[14] 3.3V SBO# V[I/0] IRDY Key Area AD[16] 3.3V AD[23] V[I/0] AD[28] 3.3V RST# V[I/0] INTC# TMS TRST# AD[8] AD[21] C/BE[3]# AD[26] AD[30] REQ# BRSVP1A5 BRSVP1A4 INTA# TCK 5V GND AD[20] GND AD[25] GND CLK GND INTP 5V TDO +12V C/BE[2]# AD[19] AD[22] AD[24] AD[27] AD[31] GNT# INTS INTD# TDI 5V GND GND GND GND GND GND GND GND GND GND GND PIN Row F Row E Row D Row C Row B Row A PMC Slot 2.0 mm ERmet PIN 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 12-14 11 10 9 8 7 6 5 4 3 2 1 P2/J2 C O N N E C T O R P1/J1 C O N N E C T O R Per PXI Specification R1.0 August 20, 1997, Table 4.9 Signals in Bold are PXI specific Catalog E 07/10 Edition 1 www.erni.com 285 2.0 mm ERmet Hard Metric Connector System PXI System Slot Pinout PIN 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 12-14 11 10 9 8 7 6 5 4 3 2 1 PIN Z GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND A PXI_RSVA22 CLK6 CLK5 GND PXI_TRIG3 PXI_TRIG2 PXI_TRIG1 PXI_BRSVA15 AD[35] AD[38] AD[42] AD[45] AD[49] AD[52] AD[56] AD[59] AD[63] C/BE[5]# V[I/0] CLK4 CLK2 CLK1 5V AD[1] 3.3V AD[7] 3.3V AD[12] 3.3V SERR# 3.3V DEVSEL# 3.3V B PXI_RSVB22 GND GND GND PXI_TRIG4 GND PXI_TRIG0 GND AD[34] GND AD[41] GND AD[48] GND AD[55] GND AD[62] GND PXI_BRSVB4 GND CLK3 GND REQ64# 5V AD[4] GND AD[9] GND AD[15] GND SDONE GND FRAME# GND GND GND GND GND GND GND GND GND GND GND Z AD[18] AD[21] C/BE[3]# AD[26] AD[30] REQ# BRSVP1A5 BRSVP1A4 INTA# TCK 5V A AD[17] GND IDSEL GND AD[29] GND BRSVP1B5 GND INTB# 5V -12V B C PXI_RSVC22 RSV RSV RSV PXI_TRIG5 PRST# DEG# FAL# AD[33] V[I/0] AD[40] V[I/0] AD[47] V[I/0] AD[54] V[I/0] AD[61] V[I/0] C/BE[7]# GNT3# SYSEN# REQ1# ENUM# V[1/0] AD[3] 3.3V AD[8] V[I/0] AD[14] 3.3V SBO# V[I/0] IRDY# Key Area AD[16] 3.3V AD[23] V(I/O) AD[28] 3.3V RST# V(I/O) INTC# TMS TRST# C D PXI_RSVD22 RSV GND RSV GND REQ6# GND REQ5# GND AD[37] GND AD[44] GND AD[51] GND AD[58] GND C/BE[4]# GND REQ4# GNT2# GNT1# 3.3V AD[0] 5V AD[6] M66EN AD[11] GND PAR GND STOP# GND E PXI_RSVE22 RSV RSV RSV PXI_TRIG6 GNT6# PXI_TRIG7 GBT5# AD[32] AD[36] AD[39] AD[43] AD[46] AD[50] AD[53] AD[57] AD[60] PAR64 C/BE[6]# GNT4# REQ3# REQ2# 5V ACK64# AD[2] AD[5] C/BE[0]# AD[10] AD[13] C/BE[1] PERR# LOCK# TRDY# F GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND AD[20] GND AD[25] GND CLK GND INTP 5V TDO +12V D C/BE[2]# AD[19] AD[22] AD[24] AD [27] AD [31] GNT# INTS INTD# TDI 5V E GND GND GND GND GND GND GND GND GND GND GND F P2/J2 C O N N E C T O R P1/J1 C O N N E C T O R Per PXI Specification R1.0 August 20, 1997, Table 4.10 Signals in Bold are PXI specific 286 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System PXI Star Trigger Slot Pinout Z GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND A PXI_RSVA22 PXI_LBRO PXI_LBR4 PXI_STAR2 PXI_TRIG3 PXI_TRIG2 PXI_TRIG1 PXI_BRSVA15 AD[35] AD[38] AD[42] AD[45] AD[49] AD[52] AD[56] AD[59] AD[63] C/BE[5]# V(I/O) PXI_LBR7 PXI_LBR11 PXI_STAR9 5V AD[1] 3.3V AD[7] 3.3V AD[12] 3.3V SERR# 3.3V DEVSEL# 3.3V B PXI_RSVB22 GND PXI_LBR5 GND PXI_TRIG4 GND PXI_TRIG0 GND AD[34] GND AD[41] GND AD[48] GND AD[55] GND AD[62] GND PXI_BRSVB4 GND PXI_LBR12 GND REQ64# 5V AD[4] GND AD[9] GND AD[15] GND SDONE GND FRAME# GND GND GND GND GND GND GND GND GND GND GND Z AD[18] AD[21] C/BE[3]# AD[26] AD[30] REQ# BRSVP1A5 BRSVP1A4 INTA# TCK 5V A AD[17] GND IDSEL GND AD[29] GND BRSVP1B5 GND INTB# 5V -12V B C PXI_RSVC22 PXI_LBR1 PXI_STARO PXI_STAR3 PXI_TRIG5 PRST# DEG# FAL# AD[33] V[I/0] AD[40] V[I/0] AD[47] V(I/O) AD[54] V(I/O) AD[61] V(I/O) C/BE[7]# PXI_LBR8 SYSEN# PXI_STAR10 ENUM# V[I/0] AD[3] 3.3V AD[8] V[I/0] AD[14] 3.3V SBO# V(I/O) IRDY# Key Area AD[16] 3.3V AD[23] V[I/0] AD[28] 3.3V RST# V[I/0] INTC# TMS TRST# C D PXI_RSVD22 PXI_LBR2 GND PXI_STAR4 GND PXI_CLK10_IN GND PXI_STAR6 GND AD[37] GND AD[44] GND AD[51] GND AD[58] GND C/BE[4]# GND PXI_LBR9 PXI_STAR7 PXI_STAR11 3.3V AD[0] 5V AD[6] M66#N AD[11] GND PAR GND STOP# GND E PXI_RSVE22 PXI_LBR3 PXI_STAR1 PXI_STAR5 PXI_TRIG6 PXI_CLK10 PXI_TRIG7 PXILBR6 AD[32] AD[36] AD[39] AD[43] AD[46] AD[50] AD[53] AD[57] AD[60] PAR64 C/BE[6]# PXI_LBR10 PXI_STAR8 PXI_STAR12 5V ACK64# AD[2] AD[5] C/BE[0]# AD[10] AD[13] C/BE[1]# PERR# LOCK# TRDY# F GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND AD[20] GND AD[25] GND CLK GND INTP 5V TDO +12V D C/BE[2]# AD[19] AD[22] AD[24] AD[27] AD[31] GNT# INTS INTD# TDI 5V E GND GND GND GND GND GND GND GND GND GND GND F 2.0 mm ERmet PIN 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 12-14 11 10 9 8 7 6 5 4 3 2 1 PIN P2/J2 C O N N E C T O R P1/J1 C O N N E C T O R Per PXI Specification R1.0 August 20, 1997, Table 4.11 Signals in Bold are PXI specific Catalog E 07/10 Edition 1 www.erni.com 287 2.0 mm ERmet Hard Metric Connector System VME64x on CompactPCI(R) J4/P4 and J5/P5 Pin Assignments PIN 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 12-14 11 10 9 8 7 6 5 4 3 2 1 A ResU(1) ResU(1) GND MPR MCLK GND MSD MMD GND MCTL BCLR* GND BBSY* BGOIN* GND BGOOUT* BG1IN* GND BG1OUT* BG2IN* GND BG2OUT* BG3IN* GND BG3OUT* BRO* GND BR1* BR2* GND BR3* LI/I*(1) LI/0*(1) B +3.3V ACFAIL* SYSCLK +3.3V SYSFAIL SYSRST* +3.3V AM5 WRITE* +3.3V AMO AMI +3.3V AM2 AM3 GAP* AM4 ResB[z13](2) GA2* RsvB[z15] RsvB[z17] +5V RsvB[z19] RsvB[z21] +5V RsvB[z23] RsvB[z25] +5V SERA SERB -12V SBB SBA IACK* IRQ5* GND UD UD UD UD UD UD UD UD IACKIN* IRQ4* GND UD UD UD UD UD UD UD UD PIN A B C DOO +3.3V D10 D03 +3.3V D13 D06 +3.3V A23 A22 +V1 A17 A16 -V1 A13 A05 GAO* A10 A02 GA3* A25 A26 +5V A31 D16 +5V D21 D22 +5V D27 D28 VPC(2) ResU(1) Key Area IACKOUT* IRQ3* GND UD UD UD UD UD UD UD UD C D DO8 DO9 +3.3V D11 D12 +3.3V D14 D15 +3.3V A21 A19 +V2 A15 A14 -V2 A12 A11 GA1* A09 A08 GA4* A27 A29 +5V D17 D19 +5V D23 D25 +12V D29 D31 GND(3) E DO1 DO2 BERR* D04 D05 RTRY1* D07 LWORD* DS1* A20 A18 DSO* A07 A06 DTACK* A04 A03 AS* A01 A24 RETRY* A28 A30 RsvB[d19] D18 D20 RsvB[d21] D24 D26 RsvB[d23] D30 ResB[d25](2) ResB[z27](2) F GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND IRQ7* IRQ2* GND UD UD UD UD UD UD UD UD IRQ6* IRQ1* GND UD UD UD UD UD UD UD UD GND GND GND GND GND GND GND GND GND GND GND D E F P5/J5 C O N N E C T O R P4/J4 C O N N E C T O R Per PICMG 2.2 R1.0 August 7, 1998, Table 1 Notes: (1) These signals are not bused (feed through the backplane). (2) ResB is the ResBus (reserved bused) signal pins Connector Key is Reseda Green (ERNI P/N 043346 male, 043336 female) 288 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System PMC Mezzanine Card I/O Pin Assignments 2.0 mm ERmet Single PMC's I/O Signal Mapping to CompactPCI(R) 3U J2 Connector PIN Row F Row E Row D 22 GND UD UD 21 GND UD UD 20 GND UD UD 19 GND UD UD 18 GND UD UD 17 GND UD UD 16 GND UD UD 15 GND UD UD 14 GND +5V +5V 13 GND 1 2 12 GND 6 7 11 GND 11 12 10 GND 16 17 9 GND 21 22 8 GND 26 27 7 GND 31 32 6 GND 36 37 5 GND 41 42 4 GND 46 47 3 GND 51 52 2 GND 56 57 1 GND 61 62 PIN Row F Row E Row D Per PICMG 2.3 R1.0 August 7, 1998, Table 1 Notes: 1. Entries in table are of the PMC Jn4 pin number. 2. UD are the remaining user defined I/0 pins that can be used for other I/O functions. Row C UD UD UD UD UD UD UD UD +3.3V 3 8 13 18 23 28 33 38 43 48 53 58 63 Row C Row B UD UD UD UD UD UD UD UD +3.3V 4 9 14 19 24 29 34 39 44 49 54 59 64 Row B Row A UD UD UD UD UD UD UD UD +3.3V 5 10 15 20 25 30 35 40 45 50 55 60 VI/O Row A J2 C O N N E C T O R Dual PMC Slot's I/O Signal Mapping to CompactPCI(R) 6U J3/P3 & J4/P4 Connectors PIN 9 8 7 6 5 4 3 2 1 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Row B GND 4 9 14 19 24 29 34 39 44 49 54 59 64 +3.3V 4 9 14 19 24 29 34 39 44 49 54 59 64 Row A GND 5 10 15 20 25 30 35 40 45 50 55 60 VI/0 +3.3V 5 10 15 20 25 30 35 40 45 50 55 60 VI/O PMC Slot PIN Row F Row E Row D Row C Row B Per PICMG 2.3 R1.0 August 7, 1998, Table 2 Notes: 1. Entries in table are of the PMC Jn4 pin number. Row A PMC Slot Catalog E Row F GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND 07/10 Row E GND 1 6 11 16 21 26 31 36 41 46 51 56 61 +5V 1 6 11 16 21 26 31 36 41 46 51 56 61 Row D GND 2 7 12 17 22 27 32 37 42 47 52 57 62 +5V 2 7 12 17 22 27 32 37 42 47 52 57 62 Edition 1 Row C GND 3 8 13 18 23 28 33 38 43 48 53 58 63 +3.3V 3 8 13 18 23 28 33 38 43 48 53 58 63 www.erni.com A A A A A A A A A A A A A A&B B B B B B B B B B B B B B J4 C O N N E C T O R J3 C O N N E C T O R 289 2.0 mm ERmet Hard Metric Connector System PMC Mezzanine Card I/O Pin Assignments Single PMC Slot's I/O Signal Mapping to CompactPCI(R) J5/P5 Connector PIN 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 PIN Row F GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND Row F Row E 1 6 11 16 21 16 31 36 41 46 51 1 6 11 16 21 26 31 36 41 46 51 Row E Row D 2 7 12 17 22 17 32 37 42 47 52 2 7 12 17 22 27 32 37 42 47 52 Row D Row C 3 8 13 18 23 18 33 38 43 48 53 3 8 13 18 23 28 33 38 43 48 53 Row C Row B 4 9 14 19 24 19 34 39 44 49 54 4 9 14 19 24 29 34 39 44 49 54 Row B Row A 5 10 15 20 25 30 35 40 45 50 55 5 10 15 20 25 30 35 40 45 50 55 Row A J5 C O N N E C T O R Per PICMG 2.3 R1.0 August 7, 1998, Table 3 Notes: 1. Entries in table are of the PMC Jn4 pin number. 2. UD are the remaining user defined I/0 pins that can be used for other I/O functions. Dual PMC Slot's I/O Signal Mapping to CompactPCI(R) J5/P5 Connector PIN 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 PIN Row F GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND Row F Row E 1 6 11 16 21 16 31 36 41 46 51 1 6 11 16 21 26 31 36 41 46 51 Row E Row D 2 7 12 17 22 17 32 37 42 47 52 2 7 12 17 22 27 32 37 42 47 52 Row D Row C 3 8 13 18 23 18 33 38 43 48 53 3 8 13 18 23 28 33 38 43 48 53 Row C Row B 4 9 14 19 24 19 34 39 44 49 54 4 9 14 19 24 29 34 39 44 49 54 Row B Row A 5 10 15 20 25 30 35 40 45 50 55 5 10 15 20 25 30 35 40 45 50 55 Row A PMC Slot A A A A A A A A A A A B B B B B B B B B B B PMC Slot J5 C O N N E C T O R Per PICMG 2.3 R1.0 August 7, 1998, Table 4 Notes: 1. Entries in table are of the PMC Jn4 pin number. 290 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System IP Mezzanine Module I/O Pin Assignments 2.0 mm ERmet I/O Signal Mapping to CompactPCI(R) J2 Connector PIN 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 PIN Row F GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND Row F Row E B5 B10 B15 B20 B25 B30 B35 B40 B45 B50 +5V A5 A10 A15 A20 A25 A30 A35 A40 A45 A50 +5V Row E Row D B4 B9 B14 B19 B24 B29 B34 B39 B44 B49 +5V A4 A9 A14 A19 A24 A29 A34 A39 A44 A49 +5V Row D Row C B3 B8 B13 B18 B23 B28 B33 B38 B43 B48 +3.3V A3 A8 A13 A18 A23 A28 A33 A38 A43 A48 +3.3V Row C Row B B2 B7 B12 B17 B22 B27 B32 B37 B42 B47 +3.3V A2 A7 A12 A17 A22 A27 A32 A37 A42 A47 +3.3V Row B Row A B1 B6 B11 B16 B21 B26 B31 B36 B41 B46 +3.3V A1 A6 A11 A16 A21 A26 A31 A36 A41 A46 +3.3V Row A IP Module IP-B IP-B IP-B IP-B IP-B IP-B IP-B IP-B IP-B IP-B IP-A IP-A IP-A IP-A IP-A IP-A IP-A IP-A IP-A IP-A J2 C O N N E C T O R IP Module Per PICMG 2.4 R1.0 August 7, 1998, Table 1 Catalog E 07/10 Edition 1 www.erni.com 291 2.0 mm ERmet Hard Metric Connector System IP Mezzanine Module I/O Pin Assignments I/O Signal Mapping to CompactPCI(R) J5 and J4 Connector PIN 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 12 - 14 11 10 9 8 7 8 7 6 5 4 3 2 1 PIN Row F GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND Row E D5 D10 D15 D20 D25 D30 D35 D40 D45 D50 +5V C5 C10 C15 C20 C25 C30 C35 C40 C45 C50 +5V B5 B10 B15 B20 B25 B30 B35 B40 B45 B50 +5V Row D D4 D9 D14 D19 D24 D29 D34 D39 D44 D49 +5V C4 C9 C14 C19 C24 C29 C34 C39 C44 C49 +5V B4 B9 B14 B19 B24 B29 B34 B39 B44 B49 +5V GND GND GND GND GND GND GND GND GND GND GND GND GND Row F A5 A10 A15 A20 A25 A20 A25 A30 A35 A40 A45 A50 +5V Row E A4 A9 A14 A19 A24 A19 A24 A29 A34 A39 A44 A49 +5V Row D Row C D3 D8 D13 D18 D23 D28 D33 D38 D43 D48 +3.3V C3 C8 C13 C18 C23 C28 C33 C38 C43 C48 +3.3V B3 B8 B13 B18 B23 B28 B33 B38 B43 B48 +3.3V Key Area A3 A8 A13 A18 A23 A18 A23 A28 A33 A38 A43 A48 +3.3V Row C Row B D2 D7 D12 D17 D22 D27 D32 D37 D42 D47 +3.3V C2 C7 C12 C17 C22 C27 C32 C37 C42 C47 +3.3V B2 B7 B12 B17 B22 B27 B32 B37 B42 B47 +3.3V Row A D1 D6 D11 D16 D21 D26 D31 D36 D41 D46 +3.3V C1 C6 C11 C16 C21 C26 C31 C36 C41 C46 +3.3V B1 B6 B11 B16 B21 B26 B31 B36 B41 B46 +3.3V IP Module IP-D IP-D IP-D IP-D IP-D IP-D IP-D IP-D IP-D IP-D A2 A7 A12 A17 A22 A17 A22 A27 A32 A37 A42 A47 +3.3V Row B A1 A6 A11 A16 A21 A16 A21 A26 A31 A36 A41 A46 +3.3V Row A IP-A IP-A IP-A IP-A IP-A IP-A IP-A IP-A IP-A IP-A IP-A IP-A IP-C IP-C IP-C IP-C IP-C IP-C IP-C IP-C IP-C IP-C IP-B IP-B IP-B IP-B IP-B IP-B IP-B IP-B IP-B IP-B J5 C O N N E C T O R J4 C O N N E C T O R IP Module Per PICMG 2.4 R1.0 August 7, 1998, Table 2 292 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System 2.0 mm ERmet Bellcore Lubrication For some telecom applications particularly those being sold to the various regional telephone companies, lubricated contacts are specified. There are many different ways of meeting this end customer requirement. ERNI will provide pre-lubricated male connectors upon request. There is an additional charge and a special part number for such connectors. It is also possible to apply the Bellcore lubricant to the male backplane connectors after the backplanes have been assembled. This process has the advantage that the lubricant is not as likely to be damaged or removed by subsequent handling as it is when the connectors are lubricated before assembly. Many end users do not require that lubrication be applied to the female receptacles as the lubricant is easily transferred to the female contacts after mating with a lubricated male contact. Lubricating the male contacts is a practical solution as it is quite difficult for an end customer to inspect the female connector contacts because they are hidden within the insulator. BELLCORE Requirements Summary In accordance with Bellcore GR-1217 UNCONTROLLED ENVIRONMENT CENTRAL OFFICE Shocks and Vibration - 24 hr., 18 shocks Temperature Life - 500 hr., 85C Humidity and Temp Cycle - 25C - 65C MFG TEST - 10 days, less gas concentration Shocks and Vibration - 24 hr., 18 shocks Temperature Life - 1,000 hr., 105C Humidity and Temp Cycle - 5C - 85C MFG TEST - 20 days, more gas concentration Level I * Commercial Grade * Vendor Qualification Process * Commercial Grade * Vendor Qualification Process Level II Level I with: * Tested for less than 1 in 1,000 failures over 10 year life * Monitor parametric attributes * Approved by OEM * Ship to stock allowed * Requalify every 5 years Level I with: * Tested for less than 1 in 1,000 failures over 10 year life * Monitor parametric attributes * Approved by OEM * Ship to stock allowed * Requalify every 5 years Level III Level II with: * Tested for less than 1 in 10,000 failures over 25 year life * Monitor parametric attributes * Ship to stock allowed, provided that connector manufacturer's data are reviewed on lot-on-lot basis * Requalify every 3 years Level II with: * Tested for less than 1 in 10,000 failures over 25 year life * Monitor parametric attributes * Ship to stock allowed, provided that connector manufacturer's data are reviewed on lot-on-lot basis * Requalify every 3 years Prequalification Tests for Quality Level II, Level III Catalog E 07/10 Edition 1 www.erni.com 293 2.0 mm ERmet Hard Metric Connector System Glossary Of Terminology Annular Ring - The circular area around a hole that is measured by the difference between the radius of the wall of the hole, subtracted from the radius of the clearance or pad around the hole. ANSI - Abbreviation for American National Standards Institute. Artwork - The representation of the electrical layout of a printed circuit on a transparency. Attenuation - When a signal travels along the bus, its amplitude decreases due to energy losses from heating, radiation, and so forth. AWG - Abbreviation for American Wire Gage. A particular series of specified diameters and thicknesses established as a standard in the U.S.A. and used for nonferrous sheets, rods and wires. Backplane - (1) A wiring board usually constructed as a printed circuit, used in micro and mini computers to provide the required connections between logic, memory and I/O modules. (2) A two-sided or multilayer printed circuit board into which function cards can be plugged. The backplane transfers signals between the function cards. Mounted on the component side of the backplane are connectors into which function cards can be plugged. On the solder side of the backplane are termination points (studs, power bugs, quick disconnects) for the distribution of power and ground. Bellcore - Bell Research Corporation, originally the research division for AT&T. Conductor Spacing - The distance between adjacent traces on a printed wiring board. Crosstalk - (1) The interaction observed due to electromagnetic coupling of adjacent conductors. (2) A false signal picked up by a signal line (in an inductive manner) from an adjacent signal line. Current - The net transfer of electric charge, per unit time, along a conductor. An amount equal to the voltage/resistance and measured in Amperes. Data Bus - A bus structure used specifically to transmit data, or bits of information. Date Code - Stamped or printed on a component the week and year the component was made (i.e. 9023 is the 23rd week of the year 1990, or June 3rd-7th, 1990). Daughter Card - Same as function card or function board. Decommitted - To physically remove material from an area of a board so as to break the electrical connection to that plane. Decouple - To prevent transfer or feedback of energy from one circuit to another. Dielectric - (1) A material which is an electrical insulator that can sustain an electrical field with minimum power loss. (2) Any insulating medium that intervenes between two conductors. Dielectric Constant - The property of a material that governs the propagation delay of a signal it surrounds, denoted by er. Bus - A circuit over which data or power is transmitted. Bus Structure - A set of rules governing the circuit design of a system such as: CompactPCI(R), VME, Multibus I, Multibus II and Q-Bus, to name a few. Characteristic Impedance - Impedance is referred to as Zo, in ohms. It is the resistance seen by a digital signal and is measured between the signal line and the reference plane. This impedance is a function of the signal line geometry and is independent of the line length. Impedance is the key parameter which interrelates all performance characteristics of the backpanel, including delay, noise and distributed capacitance. CompactPCI (R) - A bus structure developed by the PICMG based on the desktop PCI architecture. Compliant - A pin whose physical structure is designed to elastically deform upon insertion into a hole. Component Side - The side of a printed wiring board or backplane into which connectors, resistors, capacitors and so forth are inserted. Component Density - The ratio of the number of components to a given area of a board. DIN - (1) Stands for Deutsches Institut fur Normung, a German organization which established many mechanical specifications for connectors and packaging. (2) Vernacular for Standard European connector having 96 pins arranged in 3 rows of 32 pins each. The rows are labeled A, B, C. DIP - Abbreviation for Dual-In-line Package. A device that has two rows or parallel pins. Usually the pins in each row are on .100" centers. Discrete Resistor - An individual resistor, as opposed to a resistor network. Distributed Capacitance - Distributed capacitance, referred to as Co, is the amount of capacitance per unit length of a signal line. ECL - Abbreviation for Emitter-Coupled-Logic, a form of current-mode logic in which the emitters of two transistors are connected to a current carrying resistor in such a way that only one will turn on at time. ECTF - The Enterprise Computer Telephony Forum is a trade association that has developed a number of specifications related to computer telephony. Their web address is: http://www.ectf.org. Conductor Width - The width of a given trace. EIA - Electronics Industry Association. 294 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Glossary Of Terminology Etch - To incise an area of a printed wiring board by immersing the board in an acid batch. The parts of the board not covered with an acid-resistant coating will be eroded. ERNIPRESS - The particular compliant section design utilized by ERNI for many DIN 41612 and D-Sub pressfit contacts. This coined, elastic section provides a very reliable gas tight connection with the plated through hole in the backplane or daughter card. Eye of the Needle - This is the compliant section design utilized by ERNI for our 2 mm ERmet pressfit contacts. This pierced and coined elastic section provides a very reliable gas tight connection with the plated through hole in the backplane or daughter card. Function Card - A printed circuit board that plugs into a slot position of a backplane. Function cards can be custom designed by the user or bought as a standard off-the-shelf item. A series of these cards can make up a system or subsystem to run machinery or many other electronic functions. Microstrip - (1) The name given to a signal line referenced above a single ground plane. (2) The outer etched portion of a backplane transmission line. Output - The current, voltage, power, or signal which a circuit or device delivers. Terminals where a device delivers its information. Pad - The circular area that commits a hole to an uncommitted layer or trace. PCMCIA - (Personal Computer Memory Card International Association). A standard for removable cards. PICMG - The PCI Industrial Computer Manufacturer's Group is a trade association that has developed a number of specifications related to personal computer architectures and CompactPCI. Their web address is http://www.picmg.org. Pin-out - A term used to describe the actual connections for each pin of a connector on a printed wiring board. GND - An abbreviation for ground. The potential referred to as zero volts. An electrical connection between any circuit and the reference potential. Plated through-hole - A hole in a printed wiring board, used to commit external or internal layers to one another produced by electro deposition of a conductive pattern. Ground Guard - The pair of traces which surround a third conductor to minimize crosstalk. Plating - To form a thin, adherent layer of material (usually metal) on an object. Ground Plane - A common conductive surface that receives and returns power/signal transmissions. PMC - PCI mezzanine card interface, defined by IEEE 1386 Ground Shield - A conductor (usually a plane), at some reference potential (e.g. zero volts), which surrounds some other insulated conductor. IEC 61076-4-101 - Global specification that governs 2mm Hard Metric equipment practices. IEC 917 (DIN 43355) - Defines a basic pitch of 0.5 mm, with n x 0.5 mm as the multiple pitch, and a system unit of 25 mm. This, in turn, relates to Hard Metric Equipment practices, IEE 1301 and DIN 43356, used for mechanical arrangement of electrical/electronic equipment, including associated board layout and connections. IEEE - Abbreviation for the Institute of Electronic and Electrical Engineers. Impedance - Resistance of a signal line measured in ohms. One of the important electrical characteristics of a backplane, impedance is determined by the physical dimensions of trace width, dielectric thickness, dielectric constant, and so forth. Inductance - The ratio of the voltage to the rate of change of current in a circuit (V/L). Layer - A plane in a printed wiring board which has a copper covering in some specified pattern (e.g. plane, traces and pads). 07/10 Pressfit - An interference connection used in the assembly process to eliminate the need for solder to make the electrical connection. Propagation Delay - (1) Referred to as tpd, commonly expressed in nanoseconds per inch (ns/in.). It is the time required for a pulse to travel through a transmission line system. (2) The time it takes for a signal to spread or distribute across an entire circuit. Rack - (See Subrack) - A sheet metal assembly that is made up of mounting bars and side plates to which a backplane can be mounted and printed wiring boards can be inserted Resistance - The opposition that a material or device offers to the flow of current, equal to the voltage drop across the element, divided by the current through the element. I/O - Abbreviation for input/output. Catalog E 2.0 mm ERmet EMI - Electromagnetic interference. Edition 1 RFI - Radio Frequency Interference. Risetime - Often designated as tr, in picoseconds. It is the time it takes the signal to transition from 10 percent to 90 percent of its' final value. Skew - The time difference between the arrival of two related signals, often due to differences in their propagation paths. Shroud - A male connector body designed to fit over the extended tails of a long tail connector which allows a female connector to be mated from the rear side for midplane or rear I/O applications. www.erni.com 295 2.0 mm ERmet Hard Metric Connector System Glossary Of Terminology Signal - An electrical pulse which conducts across a backplane. TTL - Transistor-Transistor Logic. A logic circuit containing two transistors, for driving large output capacitances at high speed. Solder or Extended Tail - A term used to specify the length of the pins on any connector. Typically the pins will protrude through the printed wiring board. Extended pins extend much further. Two Sided - A printed wiring board with only the outer layers containing traces. This product may or may not contain plated through holes. Solder Mask - The coating on a printed wiring board, placed there for protection. Also aids in assembly and soldering. U - An EIA unit of measurement equal to 1.75" for equipment racks. Un-terminated - Any bussed trace that is not connected. S-Parameters - A popular mathematical representation of high frequency characteristics of a component such as a connector utilized for signal integrity measurement and analytical techniques. Often utilized in applications where SPICE modeling is not practical. SPICE - Software Program for Integrated Circuit Emulation. One of several computer based techniques for simulating the electrical performance of various circuit components such as connectors and integrated circuits within a actual or theoretical circuit configuration. Stripline - (1) The name given to a signal, referenced between two ground planes, at a defined spacing. (2) The etched portion of a backplane transmission line that is between two ground planes in a multilayer printed circuit board. Subrack - A card cage assembly, usually designed to support a backplane, card guides and daughter cards. Terminated - A line or trace is considered terminated at any point there is a resistor connected to it. Tolerance - The permissible variations in the dimensions of manufactured parts or electrical components. Trace - The conductor that physically joins two or more points on a printed wiring board. Vcc - Typically, the collector voltage level for a transistor. The designation of the primary voltage level on a printed wiring board, usually at the potential of +5 volts. Via - A plated through-hole that is there for the sole purpose of conducting a signal trace or potential from one layer of the printed wiring board to another. VITA - The VME International Trade Association is a trade association that supports VME and other imbedded industry computer manufacturers. It also supports an ANSI recognized standards producing organization, the VSO. VITA's web address is http://www.vita.com VME - The initials for the backplane bus architecture known as Versa-Module -Europa. Voltage - The electromotive force determined by the potential difference between two conductors, measured in volts. VSO - The VITA Standards Organization. An ANSI recognized standards producing organization concerned with computer architectures. See VITA. Wirewrap - A termination technique, used mainly to prototype computers and computer systems, identifiable by the presence of elongated pins to which signal wires and voltage and ground connections can be created. Transition Board - A perpendicular board assembly used to plug into extended connector terminals on the rear side of the backplane as in mid plane chassis designs or when it is not desirable to utilize cables to interface to the rear connectors. Transmission Line - A line is referred to as a transmission line when its capacitance and inductance are distributed over the line. Such a line will convey a signal without distortion and will appear as a purely resistive input impedance. 296 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System ERNI Customer Request Form 2.0 mm ERmet If you need a specially loaded configuration for your application, please use this form. Fill out the grid diagram for the connector style you desire (A, B, C, or M) and mark which pin (A, B, C, D, E, F, K, L, M, N, P, Q, R, S or T) is required in each position. Unloaded positions or rows may be left blank. Date Submitted Connector Type A Level 3 Level 2 Level 1 Top surface of backplane Insulator Thickness Connector Type B Sample Qty. Required Date Samples Needed Connector Type M Connector Type C Estimated Annual Usage Special Markings or Other Requirements Connector with location peg Connector without location peg Name: Tel: _____________________________________ Ext. _____________ Title: Fax: Company: E-mail: Address: ________________________________________________________________________________________________________________ City: ____________________________________________________________ State: ___________________________ Zip: __________________ Catalog E 07/10 Edition 1 www.erni.com 297 2.0 mm ERmet Hard Metric Connector System ERNI Customer Request Form If you need a specially loaded configuration for your application, please use this form. Fill out the grid diagram for the connector style you desire and mark which pin (A, B, C, D, E, F, K, L, M, N, P, Q, R, S or T) is required in each position. Unloaded positions or rows may be left blank. Date Submitted Connector Type D Level 3 Level 2 Level 1 Top surface of backplane Insulator Thickness i Connector Type E Sample Qty. Required Date Samples Needed i Connector Type F Estimated Annual Usage Special Markings or Other Requirements i Connector with location peg Connector without location peg Name: Tel: _____________________________________ Ext. _____________ Title: Fax: Company: E-mail: Address: ________________________________________________________________________________________________________________ City: ____________________________________________________________ State: ___________________________ Zip: __________________ 298 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System ERNI Customer Request Form 2.0 mm ERmet If you need a specially loaded configuration for your application, please use this form. Fill out the grid diagram for the connector style you desire and mark which pin (A, B, C, D, E, F, K, L, M, N, P, Q, R, S or T) is required in each position. Unloaded positions or rows may be left blank. Date Submitted Monoblock Connector Sample Qty. Required Level 3 Level 2 Level 1 Top surface of backplane Date Samples Needed Insulator Thickness Estimated Annual Usage Special Markings or Other Requirements Name: Tel: _____________________________________ Ext. _____________ Title: Fax: Company: E-mail: Address: ________________________________________________________________________________________________________________ City: ____________________________________________________________ State: ___________________________ Zip: __________________ Catalog E 07/10 Edition 1 www.erni.com 299 2.0 mm ERmet Hard Metric Connector System Applications 300 Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Male Connectors Type A for Daughter Cards The connector is designed for gas tight, pressfit installation and is provided in two different configurations: with integrated upper ground return shield and without integrated upper ground return shield. The ERmet type A right angle male connector has a multifunction cavity that incorporates pre-alignment guides and accepts optional coding keys. This connector is designed to be used alone or in conjunction with either a type B or C. Sequential mating can be achieved by the use of the three available configurations listed below. The available chicklet configurations are denoted A, B, and C, to correspond with the contact mating lengths found in ERmet 2mm male connectors. Within each chicklet, the contact mating length will always be the same and the shield pins will always be Level 3. All dimensions in mm Dimensional Drawing Catalog E 07/10 Edition 1 www.erni.com 301 2.0 mm ERmet The ERmet type A right angle male connector provides 110 contacts in a 5 row x 25 position (3 positions used by multifunction cavity), fully loaded configuration. 2.0 mm ERmet Hard Metric Connector System Right Angle Male Connectors Type A for Daughter Cards Ordering Information Configuration Shielding Positions Type A without shield 25 923761 without shield 25 923760 without shield 25 923822 with shield 25 923763 with shield 25 923762 with shield 25 923823 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A Part Number z A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A a b c d e f Type A 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B z B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B a b c d e f Type A 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C z C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C a b c d e f Type A 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C 11 10 9 8 7 6 5 4 3 2 1 B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C 8 7 6 5 4 3 2 1 C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C z A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C a b c d e f Type A 25 24 23 22 21 20 19 18 17 16 15 z B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C a b c d e f Type A 25 24 23 22 21 20 19 18 17 16 15 11 10 9 z C C C C C C 302 C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C a b c d e f Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Male Connectors Type B for Daughter Cards The ERmet type B right angle male connector has an uninterrupted pin field with no multifunction cavity. This connector is not designed to be used alone, but is intended to be used in conjunction with either a type A or C ERmet connector. Sequential mating can be achieved by the use of the three available configurations listed below. The available chicklet configurations are denoted A, B, and C, to correspond with the contact mating lengths found in ERmet 2mm male connectors. Within each chicklet, the contact mating length will always be the same and the shield pins will always be Level 3. All dimensions in mm Dimensional Drawing Catalog E 07/10 Edition 1 www.erni.com 303 2.0 mm ERmet The ERmet type B right angle male connector provides 125 contacts in a 5 row x 25 position fully loaded configuration. The connector is designed for gas tight, pressfit installation and is provided in two different configurations: with integrated upper ground return shield and without integrated upper ground return shield. 2.0 mm ERmet Hard Metric Connector System Right Angle Male Connectors Type B for Daughter Cards Ordering Information Configuration Shielding Positions Type B without shield 25 923766 without shield 25 923764 without shield 25 923768 with shield 25 923767 with shield 25 923765 with shield 25 923769 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A Part Number z A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A a b c d e f Type B 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B z B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B a b c d e f Type B 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C z C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C a b c d e f Type B 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C 8 7 6 5 4 3 2 1 C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C z A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C a b c d e f Type B z B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C a b c d e f Type B 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 z C C C C C C 304 C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C a b c d e f Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System Right Angle Male Connectors Type C for Daughter Cards The ERmet type C female connector has pre-alignment guides. This connector can be used alone or in conjunction with either a type A, B, L, M or N ERmet connector, however it can only be installed at the lower end of a connector row. Sequential mating can be achieved by the use of the three available configurations listed below. The available chicklet configurations are denoted A, B, and C, to correspond with the contact mating lengths found in ERmet 2mm male connectors. Within each chicklet, the contact mating length will always be the same and the shield pins will always be Level 3. All dimensions in mm Dimensional Drawing Catalog E 07/10 Edition 1 www.erni.com 305 2.0 mm ERmet The ERmet type C male connector provides 55 contacts in a 5 row x 11 position fully loaded configuration. The connector is designed for gas tight, pressfit installation and is provided in two different configurations: with integrated upper ground return shield and without integrated upper ground return shield. 2.0 mm ERmet Hard Metric Connector System Right Angle Male Connectors Type C for Daughter Cards Ordering Information Configuration Shielding Positions Type C without shield 11 923828 without shield 11 923830 with shield 11 923829 with shield 11 923831 with shield 11 923833 11 10 9 8 7 6 5 4 3 2 1 A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A Part Number z A A A A A A A A A A a b c d e f Type C 11 10 9 8 7 6 5 4 3 2 1 B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B z B B B B B B B B B B a b c d e f Type C 11 10 9 8 7 6 5 4 3 2 1 A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C A A A A A C 11 10 9 8 7 6 5 4 3 2 1 B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C B B B B B C 8 7 6 5 4 3 2 1 C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C z A A A A A C A A A A A C a b c d e f Type C z B B B B B C B B B B B C a b c d e f Type C 11 10 9 z C C C C C C 306 C C C C C C C C C C C C a b c d e f Catalog E 07/10 Edition 1 www.erni.com 2.0 mm ERmet Hard Metric Connector System ERmet Thru Hole Reflow (THR) Female Connectors 2.0 mm ERmet General Technical Characteristics In the case of modern boards with SMT population, 2.0 mm H.M. ERmet thru hole reflow (THR) female connectors have been developed. The connectors have been designed for fully automatic SMT assembly. Safe positioning before the SMT soldering process is ensured by means of kinked terminations. For fully automatic feed-in into the automatic assembly machines, the connectors are supplied in a tray packaging. The high temperature resistant thermoplastic of the insulation body allows for the use of all standard reflow processes. * * * * * * Catalog E 07/10 Edition 1 Pitch: 2.0 mm Modules: A, B, C, AB Current rating: 1.5 A (20 C) Air- and creepage distance: 0.6 mm Mating cycles: > 250 Materials: Insulator: LCP Contact: Cu alloy * Plating: Mating area: Gold plated Termination area: Sn * PCB-Layout: conform to pressfit Female Connectors * Tray packaging www.erni.com 307 2.0 mm ERmet Hard Metric Connector System ERmet Thru Hole Reflow (THR) Female Connectors Ordering Information Configuration Number of Pins Termination Type A without Shield 110 THR 124698 Type A with Shield 110 THR 223214 Type AB without Shield 125 THR 123700 Type AB with Shield 125 THR 154876 Type AB 22 with Shield 110 THR 174402 Type B without Shield 125 THR 124699 Type B with Shield 125 THR 154875 Type B 22 without Shield 110 THR 123768 Type B 22 with Shield 110 THR 154872 Type B 19 without Shield 95 THR 154673 Type B 19 with Shield 95 THR 123796 Type C without Shield 55 THR 223385 Type C with Shield 55 THR 223386 308 Catalog E 07/10 Edition 1 Partnumber www.erni.com 2.0 mm ERmet Hard Metric Connector System CompactPCI Connectors acc. to PIGMG 2.0 Rev. 3.0 Late in 1999 PCI Industrial Computer Manufacturers Group (PICMG) introduced the new revision 3.0 of the CompactPCI Core Specification. Version 3.0 of this specification comprises a.o. hot swap and computer telephony specifications such as pin sequencing. For CompactPCI, the metric ERmet connectors are specified in accordance with IEC 61076-4-101 which are available in build types A, B, AB, and as monoblock versions. This new version of the CompactPCI specification has the consequence a.o. that for 3 HE backplanes on position P2 a male connector, build type B with long connection pins for AB transfer and AB Catalog E 07/10 Edition 1 2.0 mm ERmet General shrouds are inserted into position rP2. At the rear card end, on position rJ2, a sheilded female connector in build type AB is specified. For 6 HE backplanes, on P3 and P5, the male connector - build type B with long connection pins for AB transfer and AB shrouds have to be inserted into positions rP3 and rP5. At the rear card end, on positions rJ3 and rJ5, a shielded female connector, build type AB, has been specified here. On P4, a blade contact strip, build type A with long connection pins for A shroud and A shroud frames, has been specified on position rP4. For the rear card end, a shielded female connector, build type A, has been defined on rJ4. For male connectors with shrouds in build types A and B, the specification only requires a series a grounding for the upper screening panel. All necessary connectors required in accordance with the new CompactPCI specification are available from ERNI. In addition, for CompactPCI applications, ERNI also offers an economic solution for a male connector with long terminal pins, which is populated with shield contacts on row a only. In addition to the new AB compatible male connectors for CompactPCI, ERNI also supplies shrouds. Here, all shrouds are available in four different heights (3.9 mm, 4.5 mm, 5.3 mm, and 6.1 mm) in order to adapt to the printed circuit board thickness of the backplanes. www.erni.com 309 2.0 mm ERmet Hard Metric Connector System CompactPCI Connectors acc. to PIGMG 2.0 Rev. 3.0 Ordering Informations Male Connectors For Backplanes Location On The PCB Number Of Positions* Contact Loading* Part Number Type A With Peg Type A With Peg And Extended Terminals For Shrouding Type A Without Peg And With Extended Terminals For Shrouding Type B (AB Compatible) With Extended Terminals For Shrouding Type B (AB Compatible) With Extended Terminals For Shrouding Type B (AB Compatible) With Extended Terminals For Shrouding Type A With Extended Terminals For Shrouding Type A With Peg And Extended Terminals For Shrouding Type A With Peg And Extended Terminals For Shrouding Type A Without Peg Type A Without Peg And With Extended Terminals For Shrouding Type B (AB Compatible) With Extended Terminals For Shrouding Type B (AB Compatible) With Extended Terminals For Shrouding P1 25 CB---BC 923190 P1 Special 25 TP---PT 923197 P1 25 TS---ST 923342 P2, P5 22 TSSSSS- 923345 P3 19 TSSSSST 923341 P3 P4 19 25 TSSSSSS----ST 923346 923347 P4 25 TRRRRRT 064688 P4 P4 Telecom 25 25 TSSSSST ------- 103975 923160 P4 Telecom 25 ------- 923212 P5 Telecom 22 ------- 923339 P2, P5 22 TSSSSST 923340 Female Connectors For Daughter Cards Location On The PCB Number Of Positions* Part Number Type A With Shield, Without Peg Type A With Split Shield, Partially Loaded Type A With Split Shield, Partially Loaded Type AB With Shield, Without Peg Type AB With Shield, Without Peg Type B With Upper Shield Type B With Upper Shield J1, J4 J4 Telecom rJ4 Telecom rJ2, rJ5 rJ3 J2, J5 J3 25 25 25 22 19 22 19 064176 140512 104697 114809 114810 064785 064784 Shrouds For Male Connectors Location On The PCB Number Of Positions* Height Part Number Type A Shroud 25 Positions Type A Shroud 25 Positions Type A Shroud 25 Positions Type A Shroud 25 Positions Type AB Shroud 22 Positions Type AB Shroud 22 Positions Type AB Shroud 22 Positions Type AB Shroud 19 Positions Type AB Shroud 19 Positions Type AB Shroud 19 Positions Type AB Shroud 19 Positions rP1, rP4 rP1, rP4 rP1, rP4 rP1, rP4 rP2, rP5 rP2, rP5 rP2, rP5 rP3 rP3 rP3 rP3 25 25 25 25 22 22 22 19 19 19 19 14.35 14.95 15.75 16.55 14.95 15.75 16.55 14.35 14.95 15.75 16.55 114436 054795 054794 054793 114426 114427 114428 114487 114488 114489 114490 Code Number Color Part Number 1567 3456 1248 2348 1278 3567 Brilliant Blue Cadmium Yellow Strawberry Red Brilliant Blue Cadmium Yellow Strawberry Red 043347 043345 043350 043337 043335 043340 Coding Keys Application Coding Keys For Male Connectors And Shrouds Coding Keys For Male Connectors And Shrouds Coding Keys For Male Connectors And Shrouds Coding Keys For Female Connectors Coding Keys For Female Connectors Coding Keys For Female Connectors 5.0 Volts P1 3.3 Volts P1 Telecom P4 5.0 Volts J1 3.3 Volts P1 Telecom J4 * Length = 50mm Pitch = 2.0mm => 50 / 2 = 25 Positions **Cross Sectional Loading From Z To F 310 Catalog E 07/10 Edition 1 www.erni.com ERmet B8 - CompactPCI Express Connectors 2.0 mm ERmet CompactPCI Express brings PCI Express technology to the popular PICMG 2.0 CompactPCI form factor, while maintaining compatibility with CompactPCI hardware and software. The ERmet B8 connectors are designed in accordance with the standard PICMG EXP.0 CompactPCI Express. This completes the family of CompactPCI connectors supplied by ERNI (Signal: ERmet ZD, ERmet B8; Power: ERmet Power Module). The ERmet B8 enriched hard metric (eHM) connector is used for carrying I/O signals and some power. The connector is keyed and four different key combinations are possible. All combinations support Hot Swap functions. The eHM connector (ERmet B8) with coding for reliable mating is available as a 56 pin male connector (40 signal contacts and 16 additional shield blades) as well as 40 pin female connector. Catalog E 07/10 Edition 1 Features * Pitch: 2.0 mm * Number of pins: Male connector: 56 (40 signal and 16 shield) Female connector: 40 * Pressfit termination * Housing material: Male Connector: PBT Female Connector: LCP * Performance class 2 * Tray packaging * According to CompactPCI Express standard (R) CompactPCI Express www.erni.com 311 ERmet B8 - CompactPCI Express Connectors Keying Overview Male Connectors Female Connectors 312 Catalog E 07/10 Edition 1 www.erni.com ERmet B8 - CompactPCI Express Connectors Dimensional Drawings 2.0 mm ERmet Male Connectors Date Code Board hole pattern 15,4 Company label 224056 13,45 -0,1 1) 2 all holes 2 z 6 x 2 = ( 12 ) compliant zone for thru hole o 0.60.05 12 a b c d e 14 f 8 2 7x2= 7 x 2 = ( 14 ) 0.1 alle Locher X 2 6x2= (Component mounting side) ERNI 3 -0,1 Ident-Nr. 8 1 1 z o 0,6 0,05 Diameter of finished plated-through hole o 0,7 0,02 Diameter of drilled hole 1) a b c d e f 1,1 1 max. 17,56 Female Connectors 0,8 Board hole pattern (Component mounting side) 1 8 2 e 7 x 2 = ( 14 ) d 0.1 c alle Locher b Compliant zone for thru hole o 0.6 0.05 4x2= 8 a 2 7x2= 1) all holes 2 14 f d c 15,95 b 2 2 5 x 2 = 10 a 8 1 21 1.7 0.05 1.5 e 3 -0.4 10.8 -0.2 1) o 0,60,05 Diameter of finished plated-through hole o 0,7 0,02 Diameter of drilled hole 11.4 Catalog E 07/10 Edition 1 www.erni.com 313 ERmet B8 - CompactPCI Express Connectors Ordering Information Male Connectors Configuration Number of Signal Pins Termination Slot Type Keying Designator Part Number Type B8 Non-staged 40 Pressfit RI/O or no RI/O or no Bussed I/O M1 224056 Type B8 Non-staged 40 Pressfit PXI M2 224057 Type B8 Staged (Hot-swap) 40 Pressfit RI/O or no RI/O or no Bussed I/O M1 204976 Type B8 Staged (Hot-swap) 40 Pressfit PXI M2 214431 Type B8 Staged (Hot-swap) 40 Pressfit RI/O or not used M5 224312 Configuration Number of Signal Pins Termination Board Type Keying Designator Type B8 40 Pressfit RI/O F1 204975 Type B8 40 Pressfit PXI F2 214443 Type B8 40 Pressfit no RI/O or Bussed I/O F5 214444 Type B8 40 Pressfit PXI F2 224302 Female Connectors 314 Catalog E 07/10 Edition 1 Part Number www.erni.com ERmet(R) Power Modules General ERmet Power Modules ERNI Electronics has upgraded its hard metric Universal Power Module (UPM) to include new 5-, 6- and 7-pin versions. These The angled male multipoint connectors featuring pressfit technology are designed to supply power to daughter cards in conjunction with UPMs expand the existing 3-pin power modules. 2 mm ERmet connectors conforming to IEC 61076-4-101. They are offered in a high power grade which carries 12.6 A per contact (3-pin Version at 20 C). Three contact mating length are available in 1.6 mm sequence levels. Pre-mating contacts also make it possible to enable hot-swap applications. The corresponding straight female multipoint connectors are used on the backplanes. The UPMs are compatible with other 2 mm These new high-performance connectors are designed to supply and DIN 41612 connectors, and also meet the requirements for performance class 1 and comply with RoHS. power applications in line with industry standard PICMG EXP.0 CompactPCI Express (5-pin and 7-pin versions). This completes the family of connectors supplied by ERNI in accordance with the CompactPCI Express standard, and meets requirements on both the signal side (ERmet ZD, ERmet type B8) and the power side. Catalog E 07/10 Edition 1 www.erni.com 315 ERmet(R) Power Modules Electrical and Mechanical Characteristics Standard Number of Pins Male Power Module Female Power Module 3, 5, 6, 7 3, 5, 6, 7 -55/125/56 -55/125/56 -55/125 C -55/125 C Technical data Climate category DIN EN 60068-1 test b Temperature range Current rating per contact IEC 60512 test 5b Air - and creepage distance See page 5 for detailed Derating Curve. contact - contact 2.5 mm contact - contact 2.5 mm Voltage rating IEC60664 The permissible operating voltages depend on the customer application and on the applicable or specified safety requirements. Insulation coordination according to IEC 60664-1 has to be regarded for the complete electrical device. Therefore, the maximum creepage and clearance distances of the mated connectors are specified for consideration as a part of the whole current path. In practice, reductions in creepage or clearance distances may occur due to the conductive pattern of the printed board or the wiring used, and have to be taken into account separately. As a result the creepage and clearance distances for the application may be reduced compared to those of the connector. Dielectric strength IEC 60512 test 4a contact - contact 1000 Vrms contact - contact 1000 Vrms Contact resistance IEC 60512 test 2a 5 m 5 m Insulation resistance IEC 60512 test 3a 104 M 104 M Vibration, sine IEC 60512 test 6d 10 - 2000 Hz 20 g 10 - 2000 Hz 20 g Contact disturbance (while vibration test) IEC 60512 test 2e 1 s 1 s Shock, halfsine IEC 60512 test 6c 50 g 11 ms 50 g 11 ms Contact disturbance (while shock test) IEC 60512 test 2e 1s 1s Mechanical operation (mating cycles) IEC 60512 test 9a > 250 mating cycles (3 pin) > 500 mating cycles (5, 6, 7 pin) > 250 mating cycles > 500 mating cycles (5, 6, 7 pin) Insertion and withdrawal force IEC 60512 test 13a 6N 6N Gauge retention force IEC 60512 test 16e 0.2 N 0.2 N 316 Catalog E 07/10 Edition 1 www.erni.com ERmet(R) Power Modules Electrical and Mechanical Characteristics Male Power Module Female Power Module 3, 5, 6, 7 3, 5, 6, 7 PBT-GF30 PBT-GF30 CTI 200 CTI 200 UL 94 V-0 UL 94 V-0 Base material Cu alloy Cu alloy Mating area gold plated gold plated Termination area Standard Versions: Sn CompactPCI Versions: SnPb (RoHS 5/6) Standard Versions: Sn CompactPCI Versions: SnPb (RoHS 5/6) Number of Pins ERmet Power Modules Standard Housing Materials Plastic material CTI value IEC 112 UL flame rating Contact Materials Environment compatibility Recycling no flame-retardent additives, no toxic additives allows easy recycling Product-approval UL Catalog E E84703 07/10 Edition 1 E84703 www.erni.com 317 ERmet(R) Power Modules Derating Curve and PTH Drawing Derating Curve Metal Plating of Plated Through Hole 0,7 Durchmesser des metallisierten Loches Diameter of finished plated-through hole 0,6 0,02 Bohrungsdurchmesser des Loches Diameter of drilled hole 0,05 min. 0,05 Restringbreite Restring width max. 15 m min. 25 m Cu 318 Sn Catalog E 07/10 Edition 1 www.erni.com ERmet(R) Power Modules Right Angle Male ERmet Power Modules Dimensional Drawings A 9,7 0,1 3 -0,25 2 2 15,7 11,7 22,3 A 2,25 0,2 6 3 10,3 B 14,3 A B C D E Pohlzahl No of Pin 0,05 1) 2 1) 3x2= 6 A Schichtaufbau im metallisierten Loch siehe Zeichnung Seite 5 Metal plating of planted-through hole see drawing page 5 3,5 1,5 0,6 0,05 Durchmesser des metallisierten Loches 0,6 0,05 Diameter of finished plated-through hole 1,5 2 23,7 18,8 21,8 4 5 6 12 15 18 3 9 12 15 3 5 6 7 6 Kontaktubersicht/ contacts overview L = lang / long M = mittel / middle S = kurz / short +0,05 E 20,7 15,8 2 11,2 3 17,7 9,8 14,6 C x 3= D 11,7 13 Lochbild fur Leiterplatte Board hole pattern S M L All dimensions in mm. Catalog E 07/10 Edition 1 www.erni.com 319 ERmet(R) Power Modules Right Angle Male Ordering Information Configuration L L L A B C With One Contact Level S S S A B C With One Contact Level M M M A B C With One Contact Level L M L A B C With Two Contact Levels 320 No. of Pins Current per contact Termination Class Packaging Part Number 3 12.6 A Pressfit 2 Tray/72 pcs 114400 3 12.6 A Pressfit 2 Tray/72 pcs 923539 3 12.6 A Pressfit 2 Tray/72 pcs 923619 3 12.6 A Pressfit 2 Tray/72 pcs 114401 Catalog E 07/10 Edition 1 www.erni.com ERmet(R) Power Modules Right Angle Male Configuration M L M A B C With Two Contact Levels M S M A B C With Two Contact Levels S M S A B C With Two Contact Levels S L L A B C With Two Contact Levels Catalog E No. of Pins Current per contact Termination Class Packaging Part Number 3 12.6 A Pressfit 2 Tray/72 pcs 114402 3 12.6 A Pressfit 2 Tray/72 pcs 124163 3 12.6 A Pressfit 2 Tray/72 pcs 124298 3 12.6 A Pressfit 2 Tray/72 pcs 223531 07/10 Edition 1 www.erni.com 321 ERmet Power Modules Ordering Information ERmet(R) Power Modules Right Angle Male Ordering Information Configuration M L S A B C With Three Contact Levels No. of Pins Current per contact Termination Class Packaging Part Number 3 12.6 A Pressfit 2 Tray/72 pcs 114403 11.3 A Pressfit 1 Tray/48 pcs 244997 11.3 A Pressfit 1* Tray/48 pcs 244998 11.3 A Pressfit 1 Tray/48 pcs 254988 L L L L L A B C D E With One Contact Level 5 L L L L L A B C D E With One Contact Level 5 M M L M M A B C D E With Two Contact Levels 5 * RoHS 5/6 322 Catalog E 07/10 Edition 1 www.erni.com ERmet(R) Power Modules Right Angle Male Configuration No. of Pins M M M M M M A B C D E F With One Contact Level 6 L L L L L L L A B C D E F G With One Contact Level 7 L L L L L L L A B C D E F G With One Contact Level 7 M M M M M M M A B C D E F G With One Contact Level 7 Current per contact Termination Class Packaging Part Number 10.8 A Pressfit 1 Tray/39 pcs 254963 10.5 A Pressfit 1 Tray/36 pcs 254020 10.5 A Pressfit 1* Tray/36 pcs 254021 10.5 A Pressfit 1 Tray/36 pcs 254992 * RoHS 5/6 Catalog E 07/10 Edition 1 www.erni.com 323 ERmet Power Modules Ordering Information ERmet(R) Power Modules Right Angle Male Ordering Information Configuration No. of Pins L S S L S S L A B C D E F G With Two Contact Levels 7 L S S L S S L A B C D E F G With Two Contact Levels 7 Current per contact Termination Class Packaging Part Number 10.5 A Pressfit 1 Tray/36 pcs 254018 10.5 A Pressfit 1* Tray/36 pcs 254019 * RoHS 5/6 324 Catalog E 07/10 Edition 1 www.erni.com ERmet(R) Power Modules Vertical Female ERmet Power Modules Dimensional Drawings 9,95 3,7 0,3 12,15 A position A 0,5 position E 0,75 position B position C 3 2 2 position D Lochbild fur Leiterplatte Board hole pattern Dieser Bereich mu gleiches Potential auf LP-Oberflache haben. This area must have same electrical potential on surface of PCB Pohlzahl No of Pin 9,5 15,5 18,5 2 4 5 21,5 6 12 15 18 3 5 6 7 6 1,2 0,05 A B C Oberkante Tocht erkarte to surface of daughtercard REF 2 1,5 REF 1,2 2 3 1) A 3 1 Bx 3=C 1) 0,6 0,05 Durchmesser des metallisierten Loches 0,6 0,05 Diameter of finished plated-through hole Schichtaufbau im metallisierten Loch siehe Zeichnung Seite 5 Metal plating of plated-through hole see drawing page 5 All dimensions in mm. Catalog E 07/10 Edition 1 www.erni.com 325 ERmet(R) Power Modules Vertical Female Ordering Information No. of Pins Current per contact Termination Class Packaging Part Number 3 12.6 A Pressfit 2 Tray/150 pcs 114404 5 11.3 A Pressfit 1 Tray/90 pcs 244995 5 11.3 A Pressfit 1* Tray/90 pcs 244996 6 10.8 A Pressfit 1 Tray/75 pcs 254927 7 10.5 A Pressfit 1 Tray/65 pcs 254016 * RoHS 5/6 326 Catalog E 07/10 Edition 1 www.erni.com ERmet(R) Power Modules Vertical Female Configuration 7 No. of Pins 10.5 A Current per contact Pressfit Termination 1* Class Packaging Part Number Tray/65 pcs 254017 * RoHS 5/6 Catalog E 07/10 Edition 1 www.erni.com 327 ERmet Power Modules Ordering Information ERmet(R) Female Connectors New Design ERNI is offering a new design for its A, AB, B, C, B22 and B19 module product lines. The connectors are designed for gas tight pressfit installations and are offered in two different configurations: with integrated upper ground return shields and without integrated upper ground return shields. Lower ground return shields are available seperately. The new design with the improved eye of the needle pressfit terminals and a larger supporting surface provides an easier and more reliable installation process onto the pcb. Catalog E 07/10 Edition 1 Features * Larger distance to the edge of the pcb compensates larger tolerances and enables v-scoring pcb manufacturing. * Increase of supporting surface ensures higher absorbtion of press-in forces and avoids damages to connector and pcb. * Improved eye of the needle pressfit zone accounts for a smoother and more secure press-in process and excludes damaging of the PTHs, eyelets, outer and inner copper layers. * The new housing design provides improved fixation of the chicklets. www.erni.com 328 ERmet(R) Female Connectors New Design Electrical and Mechanical Characteristics Standard Type A, AB, B, C, B22, B19 Number of Pins 55, 95, 110, 125 Technical Data Climate category DIN EN 60068-1 test b Temperature range Current rating per contact -55/125/56 -55/125 C IEC60512 test 5b Air - and creepage distance 1.0 A at 70 C 0.6 mm Operating voltage IEC 60664 The permissible operating voltages depend on the customer application and on the applicable or specified safety requirements. Insulation coordination according to IEC 60664-1 has to be regarded for the complete electrical device. Therefore, the maximum creepage and clearance distances of the mated connectors are specified for consideration as a part of the whole current path. In practice, reductions in creepage or clearance distances may occur due to the conductive pattern of the printed board or the wiring used, and have to be taken into account separately. As a result the creepage and clearance distances for the application may be reduced compared to those of the connector. Dielectric strength IEC 60512 test 4a contact - contact 750 Vrms Contact resistance IEC 60512 test 2a < 20 m1 Insulation resistance IEC 60512 test 3a > 104 M1 Vibration, sine IEC 60512 test 6d 10 - 2000 Hz 20 g Contact disturbance (while vibration test) IEC 60512 test 2e < 1 s Shock, halfsine IEC 60512 test 6c 50 g 11 ms Contact disturbance (while shock test) IEC 60512 test 2e < 1 s Mechanical operation (mating cycles) IEC 60512 test 9a > 250 mating cycles Insertion and withdrawal force IEC 60512 test 13b 0.75 N (signal contact) 1.0 N (ground contact) Gauge retention force IEC 60512 test 16e 0.15 N 329 Catalog E 07/10 Edition 1 www.erni.com ERmet(R) Female Connectors New Design Electrical and Mechanical Characteristics Standard Number of Pins Type A, AB, B, C, B22, B19 55, 95, 110, 125 Process-conditions Warning soldering of pressfit connectors not to be recommended Housing Materials Plastic material PBT 30% glass filled UL flame rating UL 94 V-0 Contact Materials Base material Phosphor bronze Mating area gold plated Termination area Sn Environment compatibility Recycling Catalog E no flame-retardent additives, no toxic additives allows easy recycling 07/10 Edition 1 www.erni.com 330 ERmet(R) Female Connectors New Design Dimensional Drawing For example Type A with shield 331 Catalog E 07/10 Edition 1 www.erni.com ERmet(R) Female Connectors New Design Ordering Information Configuration No. of Signal Pins Part Number Type A, without peg, without shield 110 354141 Type A, without peg, with shield 110 354142 Type A, with peg, without shield 110 364297 Type A, with peg, with shield 110 364298 Type B, without shield 125 354143 Type B, with shield 125 354144 Type AB, with shield 125 354866 Type C, with peg, without shield 55 354149 Type C, with peg, with shield 55 354150 Type C, without peg, without shield 55 354865 Type B22, without shield 110 354147 Type B22, with shield 110 354148 Type B19, without shield 95 354145 Type B19, with shield 95 354146 Catalog E 07/10 Edition 1 www.erni.com 332