GLS85LS1004A / 1008A / 1016A / 1032A Commercial Temp SATA NANDriveTM Fact Sheet 01.200 August 2013 Features Industry Standard Serial ATA (SATA) Host Interface 1) - SATA 1.5 Gb/s or SATA 3.0 Gb/s - ATA/ATAPI-8 compliant - Supports 48-bit address feature set Performance - Sustained sequential data read Up to 70 MByte/sec* - Sustained sequential data write Up to 30 MByte/sec* Integrated Voltage Detector - Detects supply voltage fluctuations and generates reset during power-up and powerdown to prevent inadvertent writes Supports SMART Commands Expanded Data Protection - Added data security through user-selectable protection zones 20-Byte Serial Number - Factory pre-programmed 10-Byte unique ID - User-programmable 10-Byte ID Robust Built-in ECC NAND Configuration - Two bits per cell (MLC) Commercial Temperature Range - 0C to 70C FBGA package - 14.0 mm x 24.0 mm x 1.95 mm, 145-ball, 1.0 mm ball pitch, FZJE All Devices are RoHS Compliant * measured using 128 KByte block size Power Management - 3.3V and 1.2Vpower supply - Host SATA interface power management - Immediate disabling of unused circuitry without host intervention 2) Power Specifications - Active mode: 945mW typical (GLS85LS1032A) 650mW typical (GLS85LS1016A) 490mW typical (GLS85LS1008A) 400mW typical (GLS85LS1004A) - Idle mode: 210mW typical - Standby mode: 190mW typical 1) 2) Current product revision will only support SATA Revision 1.x with host transfer rate of up to 1.5 Gb/s (i.e. SATA 1.5 Gb/s). SATA 3.0 Gb/s refers to SATA Revision 2.x and will be supported by our planned future product revisions. For management of the Sleep Mode, refer to "SATA NANDrive Application Design Guide." Product Description The GLS85LS1004A / 1008A / 1016A / 1032A Commercial Temperature SATA NANDriveTM devices (referred to as "SATA NANDrive" in this datasheet) are high-performance, fully integrated solid state drives. They combine an advanced Greenliant SATA NAND controller and 4, 8, 16 or 32 GByte of NAND flash in a multi-chip package. These products are ideal for embedded and portable applications that require smaller form-factor and more reliable data storage. The integrated NAND flash controller with built-in advanced NAND management firmware communicates with the host through the standard SATA protocol. It does not require any additional or proprietary software such as the Flash File System (FFS) and Memory Technology Driver (MTD). SATA-interface solid state mass storage technology is widely used in portable and industrial computers, settop boxes, multi-functional printers, point-of-sales terminals, video and audio recorders, medical instruments and car infotainment systems. SATA NANDrive's advanced NAND management technology enhances data reliability and security, improves endurance and accurately estimates the remaining lifespan of the NAND flash devices. This innovative technology combines robust NAND controller hardware error correction capabilities with advanced wear-leveling algorithms and bad block management to significantly extend the life of the product. SATA NANDrive is pre-programmed with a 10-Byte unique serial ID and has the option of programming an additional 10-Byte serial ID for even greater system security. SATA NANDrive is a single device, solid state drive (SSD) that provides the functionality and compatibility of a complete SATA hard disk drive (HDD) in a 14 mm x 24 mm BGA package for easy, space saving mounting to a system motherboard. These products surpass traditional storage in their small size, security, reliability, ruggedness and low power consumption. These specifications are subject to change without notice. (c) 2013 Greenliant Systems SATA NANDrive devices are offered in a 145-ball BGA, 1 mm ball pitch package. 1 08/21/2013 S71429-F GLS85LS1004A / 1008A / 1016A / 1032A Commercial Temp SATA NANDriveTM Fact Sheet 01.200 August 2013 1.0 GENERAL DESCRIPTION Each SATA NANDrive contains an integrated SATA NAND flash memory controller and up to eight discrete NAND flash die in a BGA package. Refer to Figure 2-1 for the SATA NANDrive block diagram. 1.1 1.1.5 Optimized SATA NANDrive High performance is achieved through optimized hardware error detection and correction. The heart of SATA NANDrive is the SATA NAND flash memory controller which translates standard SATA signals into flash media data and control signals. The following components contribute to SATA NANDrive's operation. 1.1.1 1.1.6 Microcontroller Unit (MCU) 1.1.7 Internal Direct Memory Access (DMA) 1.2 1.3 The Flash File System handles inadvertent power interrupts and has auto-recovery capability to ensure SATA NANDrive firmware integrity. For regular power management, the host must send an IDLE_IMMEDIATE command and wait for command ready before powering down SATA NANDrive. 1.1.4 SMT Reflow Consideration The SATA NANDrive family utilizes standard NAND flash for data storage. Because the high temperature in a surface-mount soldering reflow process may alter the content on NAND flash, it is recommended to program SATA NANDrive after the reflow process. Power Management Unit (PMU) The PMU controls the power consumption of SATA NANDrive. The PMU dramatically reduces the power consumption of SATA NANDrive by putting the part of 3) the circuitry that is not in operation into sleep mode. 3) Multi-tasking Interface The multi-tasking interface enables fast, sustained write performance by allowing concurrent Read, Program and Erase operations to multiple flash media. SATA NANDrive uses internal DMA allowing instant data transfer from/to buffer to/from flash media. This implementation eliminates microcontroller overhead associated with the traditional, firmware-based approach, thereby increasing the data transfer rate. 1.1.3 Serial Communication Interface (SCI) The Serial Communication Interface (SCI) is designed for error reporting. During the product development stage, it is recommended to provide the SCI port on the PCB to aid in design validation. The MCU translates SATA commands into data and control signals required for flash media operation. 1.1.2 Error Correction Code (ECC) Advanced NAND Management SATA NANDrive's integrated controller uses advanced wear-leveling algorithms to substantially increase the longevity of NAND flash media. Wear caused by data writes is evenly distributed in all or select blocks in the device that prevents "hot spots" in locations that are programmed and erased extensively. This effective wear-leveling technique results in optimized device endurance, enhanced data retention and higher reliability required by long-life applications. For management of the Sleep Mode, refer to "SATA NANDrive Application Design Guide." Embedded Flash File System The embedded flash file system is an integral part of SATA NANDrive. It contains MCU firmware that performs the following tasks: 1. Translates host side signals into flash media writes and reads 2. Provides flash media wear leveling to spread the flash writes across all memory address space to increase the longevity of flash media 3. Keeps track of data file structures 4. Manages system security for the selected protection zones These specifications are subject to change without notice. (c) 2013 Greenliant Systems 2 08/21/2013 S71429-F GLS85LS1004A / 1008A / 1016A / 1032A Commercial Temp SATA NANDriveTM Fact Sheet 01.200 August 2013 2.0 FUNCTIONAL BLOCKS SATA NANDrive NAND Controller SATA ll HOST I/F MCU SRAM Buffer SATA I/F 3.0/1.5 Gbps Memory Channel I/F Embedded Flash File System ECC NAND NAND NAND NAND NAND Chips Chips Chips Chips Flash Memory Channel I/F Internal DMA PMU Flash Media I/F NAND I/F SCI ECC Figure 2-1: SATA NANDrive Block Diagram These specifications are subject to change without notice. (c) 2013 Greenliant Systems 3 08/21/2013 S71429-F GLS85LS1004A / 1008A / 1016A / 1032A Commercial Temp SATA NANDriveTM Fact Sheet 01.200 August 2013 3.0 Product Ordering Information GLS 85 XX LS 1 XX X 016 A - M - C XXXX - X - X - FZJ E XXX X Environmental Attribute E = non-Pb solder (RoHS Compliant) Package Modifier ZJ = 145-ball positions Package Type F = FBGA Operation Temperature C = Commercial: 0C to +70C NAND Configuration M = Two bits per cell Generation / Product Configuration A = First generation Capacity 004 = 4 GByte 008 = 8 GByte 016 = 16 GByte 032 = 32 GByte MByte or GByte Designator 0 = MByte 1 = GByte Interface S = SATA Voltage L = 3.3V Product Series 85 = NANDrive These specifications are subject to change without notice. (c) 2013 Greenliant Systems 4 08/21/2013 S71429-F GLS85LS1004A / 1008A / 1016A / 1032A Commercial Temp SATA NANDriveTM Fact Sheet 01.200 August 2013 Valid Combinations Valid product combinations are those that are in the mass production or will be in the mass production. Consult your Greenliant sales representative to confirm availability of the valid combinations and to determine availability of new product combinations. Table 3-1: SATA NANDrive Product Valid Ordering Numbers Capacity Operating Temperature Part Number Package 4GB Commercial (0C to 70C) GLS85LS1004A-M-C-FZJE FZJE, 14x24x1.95mm 8GB Commercial (0C to 70C) GLS85LS1008A-M-C-FZJE FZJE, 14x24x1.95mm 16GB Commercial (0C to 70C) GLS85LS1016A-M-C-FZJE FZJE, 14x24x1.95mm 32GB Commercial (0C to 70C) GLS85LS1032A-M-C-FZJE FZJE, 14x24x1.95mm Table 3-2: SATA NANDrive Evaluation Board Valid Ordering Numbers Capacity Operating Temperature Part Number Form Factor 4GB Commercial (0C to 70C) GLS85LS1004A-M-C-1S-K Module with SATA connector 8GB Commercial (0C to 70C) GLS85LS1008A-M-C-1S-K Module with SATA connector 16GB Commercial (0C to 70C) GLS85LS1016A-M-C-1S-K Module with SATA connector 32GB Commercial (0C to 70C) GLS85LS1032A-M-C-1S-K Module with SATA connector Table 3-3: SATA NANDrive miniSATA Evaluation Board Valid Ordering Numbers Capacity Operating Temperature Part Number Form Factor 4GB Commercial (0C to 70C) GLS85LS1004A-M-C-1mS-K JEDEC MO-300 8GB Commercial (0C to 70C) GLS85LS1008A-M-C-1mS-K JEDEC MO-300 16GB Commercial (0C to 70C) GLS85LS1016A-M-C-1mS-K JEDEC MO-300 32GB Commercial (0C to 70C) GLS85LS1032A-M-C-1mS-K JEDEC MO-300 These specifications are subject to change without notice. (c) 2013 Greenliant Systems 5 08/21/2013 S71429-F GLS85LS1004A / 1008A / 1016A / 1032A Commercial Temp SATA NANDriveTM Fact Sheet 01.200 August 2013 3.1 Package Diagram TOP VIEW 11 10 9 8 7 14.0 +/- 0.1 6 5 4 3 2 1 A B C D E F G H J K L M N P R T U V W Y AA AB AC 24.0 0.1 A1 CORNER BOTTOM VIEW 0.5 +/- 0.05 (145x) 14.0 3.0 1 1.0 2 3 4 5 6 8.0 7 8 9 10 11 1.0 A B C D E F G H J K L M N P R T U V W Y AA AB AC SIDE VIEW 1mm DETAIL Note: All linear dimensions are in millimeters. Untoleranced dimensions are nominal target values. Coplanarity: 0.15 mm. Ball opening size is 0.40 mm ( 0.05 mm). 0.40 0.05 1.80 0.15 0.15 SEATING PLANE Figure 3-1: SATA NANDrive 145-Ball, Ball Grid Array (BGA) Greenliant Package Code: FZJ These specifications are subject to change without notice. (c) 2013 Greenliant Systems 6 08/21/2013 S71429-F GLS85LS1004A / 1008A / 1016A / 1032A Commercial Temp SATA NANDriveTM Fact Sheet 01.200 August 2013 Revision History Revision 01.000 01.001 01.002 01.003 01.004 01.200 Description Initial release of Fact Sheet for GLS85LS1004A / 1008A / 1016A / 1032A Updated Power Specifications and Table 3-1 Updated Power Specifications on page 1 Corrected typo on first page and in Table 3-1 Updated first page and figure 4-1 Changed Commercial Grade to Commercial Temp in document title; Removed Pin Assignments and Updated section numbering; Placed Valid Combinations into table format in Section 3.0 Date September 13, 2011 December 22, 2011 January 24, 2012 March 12, 2012 May 22, 2012 August 21, 2013 (c) 2013 Greenliant Systems. All rights reserved. Greenliant and the Greenliant logo are registered trademarks, and NANDrive is a trademark of Greenliant Systems. All other trademarks and registered trademarks are the property of their respective owners. Specifications are subject to change without notice. Memory sizes denote raw storage capacity; actual usable capacity may be less. Greenliant makes no warranty for the use of its products other than those expressly contained in the Greenliant Terms and Conditions of Sale. www.greenliant.com These specifications are subject to change without notice. (c) 2013 Greenliant Systems 7 08/21/2013 S71429-F Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Greenliant: GLS85LS1004A-C-M-1MS-K GLS85LS1008A-C-M-1S-K GLS85LS1032A-C-M-1S-K GLS85LS1008A-C-M-1MS-K GLS85LS1032A-C-M-1MS-K GLS85LS1016A-C-M-1S-K GLS85LS1004A-C-M-1S-K GLS85LS1016A-C-M-1MS-K GLS85LS1032A-M-C-1MS-K GLS85LS1016A-M-C-1S-K GLS85LS1032A-M-C-1S-K GLS85LS1004A-M-C-1MS-K GLS85LS1004A-M-C-1S-K GLS85LS1008A-M-C-1MS-K GLS85LS1008A-M-C-1S-K GLS85LS1016A-M-C-1MS-K