Product Data Sheet PD-0036-B 3MTM PC Boardmount Plug and Receptacle, 2 mm 95X Series Document Number: PD-0036_B Title: Product Data Sheet Subject: 3MTM PC Boardmount Plug and Receptacle, 2 mm 95X Series Issue Date: Supersedes: Page: 7/20/2010 Rev. A 1 of 7 1.0 SCOPE.....................................................................................................................................................................2 2.0 PRODUCT TESTED...............................................................................................................................................2 3.0 GENERAL CONDITIONS .....................................................................................................................................2 3.1 Test Specimens ........................................................................................................................................................2 3.2 Standard Test Conditions ........................................................................................................................................2 4.0 TEST RESULTS SUMMARY................................................................................................................................3 5.0 TESTING ................................................................................................................................................................4 5.1 General ....................................................................................................................................................................4 Visual (Appearance) -- IEC-512-2-1a ......................................................................................................................4 Low Level Contact Resistance -- IEC-512-2-2a .......................................................................................................4 5.2 Environmental .........................................................................................................................................................4 Durability -- IEC-512-7-9a ......................................................................................................................................4 Dry Heat -- IEC-512-6-11i .......................................................................................................................................4 Cold -- IEC-512-6-11j ..............................................................................................................................................5 Solderability -- IEC-512-1-12a..............................................................................................................5 5.3 Mechanical ..............................................................................................................................................................5 Mating and Unmating Forces -- IEC-512-7-13b......................................................................................................5 5.4 Electrical..................................................................................................................................................................6 Dielectric Withstanding Voltage -- IEC-512-2-4a....................................................................................................6 Insulation Resistance -- IEC-512-2-2a....................................................................................................................6 6.0 Heat Resistance Heat Resistance Compliance -- JEDEC-020C........................................................................................6 3M Electronic Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 Document Number: PD-0036_B Title: Product Data Sheet Subject: 3MTM PC Boardmount Plug and Receptacle, 2 mm 95X Series 1.0 Issue Date: Supersedes: Page: 7/20/2010 Rev. A 2 of 7 Scope This data sheet summarizes test methods, test conditions and product performance for the 3MTM PC Boardmount, 2mm, product family. Both plug and receptacle, plated with 10" Gold at the mating area. Testing has been conducted in accordance to IEC Std 60603-13 Perfomance Level 3 2.0 Product Tested Product: Product Number: Related Specification Sheet: Qualification also representative for products related to Spec Sheets: 3.0 3MTM PC Boardmount Plug and Receptacle, 2 mm 950444-6102-AR; 950444-8200-AR; 9512442520-AR TS-2155; TS-2167; TS-2157 TS-2156; TS-2158, TS-2159, TS-2160, TS-2161, TS-2162, TS-2163, TS-2164, TS-2165, TS-2166, TS-2168, TS-2174, TS-2175 General Conditions 3.1 Test Specimens The test specimens shall be strictly in compliance with the design, construction details and physical properties detailed in the relevant Technical Specification Sheet (See Section 2). 3.2 Standard Test Conditions The test shall be done under the following conditions: Temperature: Relative Humidity: Atmospheric pressure: 3M Electronic Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 15C to 35C 45% to 75% 650 to 800 mmHg Document Number: PD-0036_B Title: Product Data Sheet Subject: 3MTM PC Boardmount Plug and Receptacle, 2 mm 95X Series 4.0 Issue Date: Supersedes: Page: 7/20/2010 Rev. A 3 of 7 Test Results Summary Results Items General Visual Environmental Low Level Contact Resistance Durability Specification Test Method IEC-512-2-1a Pass IEC-512-2-2a IEC-512-7-9a Pass Pass IEC-512-6-11i Pass IEC-512-6-11j Pass IEC-512-1-12a IEC-512-7-13b Pass Pass Solderability Mating Forces No defects such as deformation, blister, damage, crack, etc. Max. R: (Initial) <20 m Insertions/Withdrawals -50 cycles Max. R: <20 m No physical abnormalities after test 100 oC for 12 Hours Max. R: <20 m No physical abnormalities after test ----25oC for 16 Hours Max. R: <20 m Solder Coverage > 95% Max force: 3N/ Contact Electrical Dielectric Withstanding Voltage Insulation Resistance 1000 Vdc 1 min > 5 X 108 @ 100 Vdc IEC-512-2-4a IEC-512-2-3a Pass Pass Heat Resistance Compliance to solder profile MSL 1 JEDEC-020c Pass Dry Heat Cold Mechanical 3M Electronic Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 Document Number: PD-0036_B Title: Product Data Sheet Subject: 3MTM PC Boardmount Issue Date: Supersedes: Page: Plug and Receptacle, 2 mm 95X Series 5.0 7/20/2010 Rev. A 4 of 7 Testing Test methods are in accordance with IEC -512. 5.1 General Visual (Appearance) -- IEC-512-2-1a Purpose The purpose of this test is to visually examine and dimensionally inspect the connector in order to determine whether the connector conforms to the applicable specification and detail documents not covered by performance requirements. Test Method The examination shall be made in accordance with IEC-512-2-1a. The visual examination shall include inspection of the following features as a minimum: workmanship, marking, materials, finish, standards, design and construction. The dimensional inspection shall be a check for compliance with the outline drawings of the detail specification. Low Level Contact Resistance -- IEC-512-2-2a Purpose The purpose of this test is to evaluate contact resistance characteristics of electrical contacts under conditions where applied voltages and currents do not alter the physical contact interface or modify the conductive oxide films which may be present. Test Method The low-signal level contact resistance shall be tested in accordance with IEC-512-2-2a with circuit current of 100 mA maximum and open circuit voltage of 20 mV maximum. All readings are in milli-ohms. 5.2 Environmental Durability -- IEC-512-7-9a Purpose The purpose of this test is to determine the effects of subjecting electrical connectors to a conditioning action of mating and unmating of connector simulating operations approximating the life of the connector. Test Method Connector durability shall be tested in accordance with IEC-512-7-9a Condition: Max speed: Max. R: 50 Cycles 10 mm/s < 20 m Dry Heat -- IEC-512-6-11i Purpose The purpose of this test is to determine the effects on the electrical and mechanical characteristics of the connector resulting from exposure of the connector under specified condition of dry heat. Test Method Mated connectors shall be tested in accordance with IEC-512-6-11i. Temperature: 3M Electronic Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 100C Document Number: PD-0036_B Title: Product Data Sheet Subject: 3MTM PC Boardmount Issue Date: Supersedes: Page: Plug and Receptacle, 2 mm 95X Series Duration: Max. R: 7/20/2010 Rev. A 5 of 7 12 hours < 20 m Cold -- IEC-512-11j Purpose The purpose of this test is to determine the effects on the electrical and mechanical characteristics of the connector resulting from exposure under specified condition of cold. Test Method Mated connectors shall be tested in accordance with IEC-512-6-11j. Temperature: Duration: Max. R: -25C 16 hours < 20 m Solderability -- IEC-512-1-12a Purpose This test is conducted to determine the suitability of connectors solder tails being adequate covered by solder after dipping process. Test Method Mated connectors shall be tested in accordance with IEC-512-1-12a. Solder: Solder bath temperature: Flux: Solder Coverage: 96.5Sn/3.0Ag/0.5Cu 260C R type > 95 % 5.3 Mechanical Mating Forces -- IEC-512-7-13b Purpose The purpose of this test is to determine the mechanical forces required to mate the electrical connectors. Test Method The mechanical forces required to mate these electrical connectors shell be determined in accordance with IEC-5127-13b. Max speed: 100 mm / min Maximum force per contact: 3 N 3M Electronic Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 Document Number: PD-0036_B Title: Product Data Sheet Subject: 3MTM PC Boardmount Plug and Receptacle, 2 mm 95X Series Issue Date: Supersedes: Page: 7/20/2010 Rev. A 6 of 7 5.4 Electrical Dielectric Withstanding Voltage -- IEC-512-2-4a Purpose The purpose of this test is to prove that a given electrical connector can operate safely at its rated voltage and withstand momentary overpotentials due to switching, surges, and other similar phenomena. Test Method Withstanding voltage shall be tested in accordance with IEC-512-2-4a. Applied Voltage: Duration: Measurement: 1000 Vdc 1 minute Check for evidence of a breakdown Insulation Resistance -- IEC-512-2-3a Purpose The purpose of this test is to establish the methods and procedures to be followed in determining the resistance offered by the insulation materials and the various seals of a connector to a direct current potential tending to produce a leakage of current through or on the surface of these members. Test Method Insulation resistance shall be tested in accordance with IEC-512-2-3a. Applied Voltage: Duration: Measurement: 3M Electronic Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 100 Vdc 1 minutes Insulation Resistance >5 X 108 @ 100 Vdc Document Number: PD-0036_B Title: Product Data Sheet Subject: 3MTM PC Boardmount Plug and Receptacle, 2 mm 95X Series Issue Date: Supersedes: Page: 7/20/2010 Rev. A 7 of 7 6.0 Heat Resistance Heat Resistance Compliance -- JEDEC-020C Purpose Purpose of this test is to assure that the part does not deform, crack, craze, blister or split under the heat environment needed for Pb-Free Assemblies and soldering with non leaded solder. Test Method Avg Ramp -Up Rate (Tsmax to Tp) Preheat Tsmin Tsmax Time (tsmin to tsmax) Time tL maintained above Temp TL TL tL Peak Tp/ Classification Time tp within 5C of Tp Ramp - Down Rate Time 25C to Tp 3C / sec max (200 - 260C) 150C 200C 60 - 180 sec 217C 60 - 150 sec 260C +3C / MSL1 20 - 40 sec 6C / sec max 8 minutes max. Results The 3MTM PC Boardmount Plug and Receptacle, 2mm, product family of parts is JEDEC-20C compliant. Important Notice The information we are furnishing you is being provided free of charge and is based on tests performed at 3M laboratory facilities or by our suppliers. While we believe that these test results a reliable, their accuracy or completeness is not guaranteed. Your results may vary due to differences in test types and conditions. This information is intended for use by persons with the knowledge and technical skills to analyze, handle and use such information. You must evaluate and determine whether the product is suitable for your intended application. The foregoing information is provided "AS-IS". In providing this information 3M makes no warranties regarding product use or performance, including any implied warranty of merchantability or fitness for a particular use. Warranty; Limited Remedy; Limited Liability. 3M's product warranty is stated in its Product Literature available upon request. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the 3M product or refund stated above, your exclusive remedy shall be, at 3M's the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. (c) 3M Copyright 2010 This document is the copyrighted property of the 3M Company and my not be reproduced without 3M written permission or used for other than 3M authorized purposes. 3M is a trademark of the 3M Company 3M Electronic Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000