New TSOP591.., TSOP593.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES * Low supply current * Photo detector and preamplifier in one package * Internal filter for PCM frequency * Improved shielding against EMI * Supply voltage: 2.7 V to 5.5 V * Suitable for short bursts: burst length 6 carrier cycles 19026 MECHANICAL DATA * Improved immunity against ambient light Pinning * Insensitive to supply voltage ripple and noise 1 = OUT, 2 = VS, 3 = GND * Compliant to RoHS directive 2002/95/EC accordance to WEEE 2002/96/EC and in DESCRIPTION The TSOP591.., TSOP593.. series are miniaturized receivers for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package acts as an IR filter. The demodulated output signal can directly be decoded by a microprocessor. The main benefit of the TSOP591.. is the compatibility to all IR remote control data formats. The TSOP593.. is optimized to better suppress spurious pulses from fluorescent lamps, LCD TVs or plasma displays. This component has not been qualified according to automotive specifications. PARTS TABLE CARRIER FREQUENCY SHORT BURSTS AND HIGH DATA RATES (AGC1) NOISY ENVIROMENTS AND SHORT BURSTS (AGC3) 30 kHz TSOP59130 TSOP59330 33 kHz TSOP59133 TSOP59333 36 kHz TSOP59136 TSOP59336 38 kHz TSOP59138 TSOP59338 40 kHz TSOP59140 TSOP59340 56 kHz TSOP59156 TSOP59356 BLOCK DIAGRAM APPLICATION CIRCUIT 17170_7 2 33 k VS 1 Input AGC Band pass Demodulator OUT 3 PIN Document Number: 81399 Rev. 1.5, 13-Nov-09 Control circuit GND Transmitter with TSALxxxx R1 IR receiver VS Circuit 16833_7 + VS C1 C OUT GND VO GND The external components R1 and C1 are optional to improve the robustnes against electrical overstress (typical values are R1 = 100 , C1 = 0.1 F). The output voltage VO should not be pulled down to a level below 1 V by the external circuit. The capacitive load at the output should be less than 2 nF. www.vishay.com 1 New TSOP591.., TSOP593.. IR Receiver Modules for Remote Control Systems Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (1) PARAMETER SYMBOL VALUE Supply voltage (pin 2) TEST CONDITION VS - 0.3 to + 6 V Supply current (pin 2) IS 5 mA VO - 0.3 to 5.5 V VS - V O - 0.3 to (VS + 0.3) V Output voltage (pin 1) Voltage at output to supply UNIT Output current (pin 1) IO 5 mA Junction temperature Tj 100 C Storage temperature range Tstg - 25 to + 85 C Operating temperature range Tamb - 25 to + 85 C Tamb 85 C Ptot 10 mW t 10 s, 1 mm from case Tsd 260 C Power consumption Soldering temperature Note (1) Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (1) PARAMETER Supply current (pin 2) TEST CONDITION SYMBOL MIN. TYP. MAX. Ev = 0, VS = 5 V ISD 0.65 0.85 1.05 Ev = 40 klx, sunlight ISH Supply voltage d IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see fig. 1 VOSL Minimum irradiance Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee min. Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee max. Angle of half transmission distance 1/2 Directivity mA 2.7 VS Output voltage low (pin 1) mA 0.95 Ev = 0, test signal see fig. 1, IR diode TSAL6200, IF = 400 mA Transmission distance UNIT 5.5 V 40 m 0.3 100 mV 0.45 mW/m2 W/m2 30 45 deg Note (1) T amb = 25 C, unless otherwise specified TYPICAL CHARACTERISTICS Tamb = 25 C, unless otherwise specified Optical Test Signal (IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms) 0.35 t tpi *) *) tpi T 6/fo is recommended for optimal function Output Signal VO 1) 2) VOH 14337 3/f0 < td < 9/f0 tpi - 4/f 0 < tpo < tpi + 6/f0 tpo - Output Pulse Width (ms) Ee 0.30 Output Pulse Width 0.25 0.20 0.15 Input Burst Length 0.10 = 950 nm, Optical Test Signal, Fig.1 0.05 0 VOL 0.1 td1 ) tpo2 ) Fig. 1 - Output Active Low www.vishay.com 2 t 21391_1 1 10 102 103 104 105 Ee - Irradiance (mW/m) Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Document Number: 81399 Rev. 1.5, 13-Nov-09 New TSOP591.., TSOP593.. IR Receiver Modules for Remote Control Systems Optical Test Signal 600 s t 600 s t = 60 ms 94 8134 Output Signal, (see fig. 4) VO VOH VOL Correlation with Ambient Light Sources: 10 W/m = 1.4 kLx (Std. illum. A, T = 2855 K) 10 W/m = 8.2 kLx (Daylight, T = 5900 K) 4.5 4 3.5 3 2.5 2 Wavelength of Ambient Illumination: = 950 nm 1.5 1 0.5 0 0.01 t t off t on 5 Ee min. - Threshold Irradiance (mW/m) Ee Ee min. - Threshold Irradiance (mW/m) Ton, Toff - Output Pulse Width (ms) 0.8 Ton 0.6 0.5 Toff 0.4 = 950 nm, Optical Test Signal, Fig. 3 0.3 0.2 0.1 21392_1 1 10 102 103 104 10 100 1 Ee - Irradiance (mW/m) f = f0 0.9 0.8 0.7 f = 30 kHz 0.6 0.5 f = 20 kHz 0.4 0.3 0.2 f = 10 kHz 0.1 f = 100 Hz 0 105 1 10 100 1000 VsRMS - AC Voltage on DC Supply Voltage (mV) 21394 Fig. 7 - Sensitivity vs. Supply Voltage Disturbances Fig. 4 - Output Pulse Diagram 1.2 E - Max. Field Strength (V/m) 500 1.0 0.8 0.6 0.4 f = f0 5 % f (3 dB) = f0/7 0.2 450 400 350 300 250 200 150 100 50 0.0 0 0.7 16926 1 Fig. 6 - Sensitivity in Bright Ambient Fig. 3 - Output Function 0.7 0.1 Ee - Ambient DC Irradiance (W/m) 21393 Ee min./Ee - Rel. Responsivity Vishay Semiconductors 0.9 1.1 1.3 f/f0 - Relative Frequency Fig. 5 - Frequency Dependence of Responsivity Document Number: 81399 Rev. 1.5, 13-Nov-09 0 20747 500 1000 1500 2000 2500 3000 f - EMI Frequency (MHz) Fig. 8 - Sensitivity vs. Electric Field Disturbances www.vishay.com 3 New TSOP591.., TSOP593.. IR Receiver Modules for Remote Control Systems Vishay Semiconductors 0 1 10 20 30 Max. Envelope Duty Cycle 0.9 0.8 0.7 40 0.6 1.0 TSOP591.. 0.5 0.9 50 0.8 60 0.4 TSOP593.. 0.3 70 0.2 0.7 80 0.1 Ee = 2 mW/m 0 0 20 40 60 80 100 120 0.6 140 19258 Burst Length (number of cycles/burst) 21590-2 0 0.2 0 0.45 0.4 0.6 10 20 30 0.4 40 0.35 1.0 0.3 0.9 50 0.25 0.8 60 0.2 0.7 70 80 0.15 - 30 - 10 10 30 50 70 0.6 90 0.4 0.5 1.0 0.45 Ee min. - Sensitivity (mW/m) 1.2 0.6 0.4 0.2 0 750 94 8408 0.2 0.4 0.6 0.4 0.35 0.3 0.25 0.2 850 950 1050 1.5 1150 - Wavelength (nm) Fig. 11 - Relative Spectral Sensitivity vs. Wavelength www.vishay.com 4 0 Fig. 13 - Vertical Directivity Fig. 10 - Sensitivity vs. Ambient Temperature 0.8 0.2 d rel - Relative Transmission Distance 19259 Tamb - Ambient Temperature (C) 21397 S ( ) rel - Relative Spectral Sensitivity 0.2 Fig. 12 - Horizontal Directivity Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length Ee min. - Threshold Irradiance (mW/m) 0.4 drel - Relative Transmission Distance 21398 2 2.5 3 3.5 4 4.5 5 5.5 VS - Supply Voltage (V) Fig. 14 - Sensitivity vs. Supply Voltage Document Number: 81399 Rev. 1.5, 13-Nov-09 New TSOP591.., TSOP593.. IR Receiver Modules for Remote Control Systems Vishay Semiconductors SUITABLE DATA FORMAT IR Signal The TSOP591.., TSOP593.. are designed to suppress spurious output pulses due to noise or disturbance signals. Data and disturbance signals can be distinguished by the devices according to carrier frequency, burst length and envelope duty cycle. The data signal should be close to the band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. When a data signal is applied to the TSOP591.., TSOP593.. in the presence of a disturbance signal, the sensitivity of the receiver is reduced to insure that no spurious pulses are present at the output. Some examples of disturbance signals which are suppressed are: IR Signal from Fluorescent Lamp with Low Modulation * DC light (e.g. from tungsten bulb or sunlight) 5 0 * Continuous signals at any frequency * Modulated IR signals from common fluorescent lamps (example of noise pattern is shown in figure 15 or figure 16) 10 15 20 Time (ms) 16920 Fig. 15 - IR Signal from Fluorescent Lamp with Low Modulation IR Signal IR Signal from Fluorescent Lamp with High Modulation 0 5 10 15 20 Time (ms) 16921 Fig. 16 - IR Signal from Fluorescent Lamp with High Modulation TSOP591.. TSOP593.. Minimum burst length 6 cycles/burst 6 cycles/burst After each burst of length a minimum gap time is required of 6 to 70 cycles 10 cycles 6 to 35 cycles 10 cycles For bursts greater than a minimum gap time in the data stream is needed of 70 cycles > 1.1 x burst length 35 cycles > 6 x burst length Maximum number of continuous short bursts/second 2000 2000 Recommended for NEC code yes yes Recommended for RC5/RC6 code yes yes Recommended for Sony code yes yes Recommended for RECS-80 code yes yes Recommended for RCMM code yes yes Recommended for r-step code yes yes Recommended for XMP code yes yes Common disturbance signals are supressed (example: signal pattern of figure 15) Even critical disturbance signals are suppressed (examples: signal pattern of figure 16) Suppression of interference from fluorescent lamps Note For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for TSOP592.., TSOP594.. . Document Number: 81399 Rev. 1.5, 13-Nov-09 www.vishay.com 5 New TSOP591.., TSOP593.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems PACKAGE DIMENSIONS in millimeters 19010 www.vishay.com 6 Document Number: 81399 Rev. 1.5, 13-Nov-09 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1