INTEGRATED CIRCUITS DATA SHEET TDA2611A 5 W audio power amplifier Product specification November 1982 NXP Semiconductors Product specification 5 W audio power amplifier TDA2611A The TDA2611A is a monolithic integrated circuit in a 9-lead single in-line (SIL) plastic package with a high supply voltage audio amplifier. Special features are: * possibility for increasing the input impedance * single in-line (SIL) construction for easy mounting * very suitable for application in mains-fed apparatus * extremely low number of external components * thermal protection * well defined open loop gain circuitry with simple quiescent current setting and fixed integrated closed loop gain. QUICK REFERENCE DATA 6 to 35 V Supply voltage range VP Repetitive peak output current IORM < 1,5 A VP = 18 V; RL = 8 Po typ. 4,5 W VP = 25 V; RL = 15 Output power at dtot = 10% Po typ. 5 W Total harmonic distortion at Po < 2 W; RL = 8 dtot typ. 0,3 % Input impedance |Zi| typ. 45 k Total quiescent current at VP = 18 V Itot typ. 25 mA Sensitivity for Po = 2,5 W; RL = 8 Vi typ. 55 mV Operating ambient temperature Tamb -25 to + 150 C Storage temperature Tstg -55 to + 150 C PACKAGE OUTLINE 9-lead SIL; plastic (SOT110B); SOT110-1. November 1982 2 NXP Semiconductors Product specification 5 W audio power amplifier TDA2611A 1 handbook, full pagewidth D1 R2 TR4 R5 R6 R11 D2 TR14 TR5 TR7 TR18 D8 TR20 R17 TR12 D5 R9 C1 TR11 D9 R15 TR15 TR16 TR13 TR10 TR1 R14 TR8 TR3 TR19 D6 D4 D3 D7 R13 TR2 2 R7 R3 TR21 TR6 R1 R4 TR9 R8 R10 R12 TR17 R16 6 4 8 5 7 MGD831 9 Fig.1 Circuit diagram; pin 3 not connected. RATINGS Limiting values in accordance with the Absolute Maximum System (IEC 134) Supply voltage VP max. 35 V Non-repetitive peak output current IOSM max. 3A Repetitive peak output current IORM max. 1,5 A Total power dissipation see derating curves Fig. 2 Storage temperature Tstg -55 to + 150 C Operating ambient temperature Tamb -25 to + 150 C November 1982 3 NXP Semiconductors Product specification 5 W audio power amplifier TDA2611A MBL006 8 handbook, full pagewidth Ptot (W) 6 infinate heatsink 4 without heatsink 2 0 -50 0 50 100 Tamb (C) 150 Fig.2 Power derating curves. HEATSINK EXAMPLE Assume VP = 18 V; RL = 8 ; Tamb = 60 C maximum; Tj = 150 C (max. for a 4 W application into an 8 load, the maximum dissipation is about 2,2 W). The thermal resistance from junction to ambient can be expressed as: 150 - 60 R th j-a = R th j-tab + R th tab-h + R th h-a = ---------------------- = 41 K/W. 2, 2 Since Rth j-tab = 11 K/W and Rth tab-h = 1 K/W, Rth h-a = 41 - (11 + 1) = 29 K/W. November 1982 4 NXP Semiconductors Product specification 5 W audio power amplifier TDA2611A D.C. CHARACTERISTICS Supply voltage range VP Repetitive peak output current IORM Total quiescent current at VP = 18 V Itot 6 to 35 V < typ. 1,5 A 25 mA A.C. CHARACTERISTICS Tamb = 25 C; VP = 18 V; RL = 8 ; f = 1 kHz unless otherwise specified; see also Fig. 3 A.F. output power at dtot = 10% > 4W VP = 18 V; RL = 8 Po VP = 12 V; RL = 8 Po typ. 1,7 W VP = 8,3 V; RL = 8 Po typ. 0,65 W VP = 20 V; RL = 8 Po typ. 6W VP = 25 V; RL = 15 Po typ. 5W typ. 0,3 % Total harmonic distortion at Po = 2 W dtot Frequency response Input impedance |Zi| Noise output voltage at RS = 5 k; B = 60 Hz to 15 kHz Vn Sensitivity for Po = 2,5 W Vi typ. 4,5 W < 1% > 15 kHz typ. 45 k(1) typ. 0,2 mV < 0,5 mV typ. 55 mV 44 to 66 mV Note 1. Input impedance can be increased by applying C and R between pins 5 and 9 (see also Figures 6 and 7). November 1982 5 NXP Semiconductors Product specification 5 W audio power amplifier 0.1 F handbook, full pagewidth TDA2611A C1 7 C2 220 pF 6 RS C5 0.1 F 1 2 TDA2611A 5 4 8 9 Vi C6 22 F (16 V) C4 470 F (16 V) C3 0.1 F C R1 3.3 R Vp RL = 8 MBL007 Fig.3 Test circuit; pin 3 not connected. MBL008 10 handbook, halfpage dtot (%) 8 (1) (2) 6 4 2 0 10-1 1 Po (W) 10 Typical values (1) RL = 8 ; VP = 18 V. (2) RL = 15 ; VP = 25 V. Fig.4 Total harmonic distortion as a function of output power. November 1982 6 NXP Semiconductors Product specification 5 W audio power amplifier TDA2611A MBL009 15 handbook, halfpage not guaranteed in view of IORM = 1,5 A Po (W) RL = 8 10 RL = 15 5 0 0 10 20 30 Vp (V) 40 Typical values: f = 1 kHz. dtot = 10%. Fig.5 Output power as a function of supply voltage. MBL010 3 handbook, full pagewidth Zi (M) 2 1 a b 0 10 102 Fig.6 November 1982 103 104 f (Hz) Input impedance as a function of frequency; curve a for C = 1 F, R = 0 ; curve b for C = 1 F, R = 1 k; circuit of Fig. 3; C2 = 10 pF; typical values. 7 105 NXP Semiconductors Product specification 5 W audio power amplifier TDA2611A MBL011 103 handbook, full pagewidth Zi (k) typ 102 10 102 103 104 105 R () Fig.7 Input impedance as a function of R in circuit of Fig. 3; C = 1 F; f = 1 kHz. MBL012 6 handbook, full pagewidth dtot (%) 4 typ 2 0 102 103 104 105 RS () Fig.8 Total harmonic distortion as a function of RS in the circuit of Fig. 3; Po = 3,5 W; f = 1 kHz. November 1982 8 106 NXP Semiconductors Product specification 5 W audio power amplifier TDA2611A MBL013 5 handbook, full pagewidth Ptot (W) 2,5 (1) (2) 0 100 (%) 50 (1) (2) 0 10-2 10-1 1 Po (W) (1) VP = 25 V; RL = 15 ; f = 1 khz. (2) VP = 18 V; RL = 8 ; f = 1 khz. Fig.9 Total power dissipation and efficiency as a function of output power. November 1982 9 10 NXP Semiconductors Product specification 5 W audio power amplifier TDA2611A APPLICATION INFORMATION handbook, full pagewidth R1 volume 220 k 1M (log) C1 560 pF R4 1M (log) Vi R2 tone C5 22 F 100 nF 8 Vp 7 C3 1 C4 100 pF R3 51 k C7 47 F 2 TDA2611A C9 3 4 6 9 220 F 100 nF C8 10 R6 RL 5 C2 10 nF C6 1 F 1 k 8 R5 MBL014 Fig.10 Ceramic pickup amplifier circuit. MBL015 10 handbook, full pagewidth dtot (%) 7,5 5 (1) (2) 2,5 0 10-2 10-1 1 Po (W) (1) With tone control. (2) Without tone control. Fig.11 Total harmonic distortion as a function of output power; in circuit of Fig. 10; typical values. November 1982 10 10 NXP Semiconductors Product specification 5 W audio power amplifier TDA2611A MBL016 5 handbook, full pagewidth Po (dB) (1) (2) 0 -5 -10 10 102 103 f (Hz) 104 (1) Tone control min. high. (2) Tone control max. high. Fig.12 Frequency characteristics of the circuit of Fig. 10; Po relative to 0 dB = 3 W; typical values. MBL017 10 handbook, full pagewidth Po (dB) 5 0 -5 10 typ 102 103 f (Hz) 104 Fig.13 Frequency characteristic of the circuit of Fig. 10; volume control at the top; tone control max. high. November 1982 11 NXP Semiconductors Product specification 5 W audio power amplifier TDA2611A PACKAGE OUTLINE SIL9MPF: plastic single in-line medium power package with fin; 9 leads SOT110-1 D D1 q A2 P1 P A3 q1 q2 A A4 seating plane E pin 1 index c L 1 9 b e Z Q b2 w M b1 0 5 10 mm scale DIMENSIONS (mm are the original dimensions) UNIT A A2 max. A3 A4 b b1 b2 c D (1) D1 E (1) e L P P1 Q q q1 q2 w Z (1) max. mm 18.5 17.8 3.7 8.7 8.0 15.8 15.4 1.40 1.14 0.67 0.50 1.40 1.14 0.48 0.38 21.8 21.4 21.4 20.7 6.48 6.20 2.54 3.9 3.4 2.75 2.50 3.4 3.2 1.75 1.55 15.1 14.9 4.4 4.2 5.9 5.7 0.25 1 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION REFERENCES IEC JEDEC JEITA ISSUE DATE 95-02-25 03-03-12 SOT110-1 November 1982 EUROPEAN PROJECTION 12 NXP Semiconductors Product specification 5 W audio power amplifier TDA2611A SOLDERING with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. Repairing soldered joints This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC Package Databook" (order code 9398 652 90011). Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 C, contact may be up to 5 seconds. Soldering by dipping or by wave The maximum permissible temperature of the solder is 260 C; solder at this temperature must not be in contact DATA SHEET STATUS DOCUMENT STATUS(1) Objective data sheet PRODUCT STATUS(2) DEFINITION Development This document contains data from the objective specification for product development. Preliminary data sheet Qualification This document contains data from the preliminary specification. Product data sheet Production This document contains the product specification. Notes 1. Please consult the most recently issued document before initiating or completing a design. 2. The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. DISCLAIMERS (including negligence), warranty, breach of contract or any other legal theory. Limited warranty and liability Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort November 1982 13 NXP Semiconductors Product specification 5 W audio power amplifier TDA2611A Suitability for use NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Terms and conditions of commercial sale NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Applications Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Export control This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. Quick reference data The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Non-automotive qualified products Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. Limiting values Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. November 1982 14 NXP Semiconductors provides High Performance Mixed Signal and Standard Product solutions that leverage its leading RF, Analog, Power Management, Interface, Security and Digital Processing expertise Customer notification This data sheet was changed to reflect the new company name NXP Semiconductors, including new legal definitions and disclaimers. No changes were made to the technical content, except for package outline drawings which were updated to the latest version. Contact information For additional information please visit: http://www.nxp.com For sales offices addresses send e-mail to: salesaddresses@nxp.com (c) NXP B.V. 2010 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Printed in The Netherlands RM5/02/pp15 Date of release: November 1982