MC74HC14A Hex Schmitt-Trigger Inverter High-Performance Silicon-Gate CMOS The MC74HC14A is identical in pinout to the LS14, LS04 and the HC04. The device inputs are compatible with Standard CMOS outputs; with pullup resistors, they are compatible with LSTTL outputs. The HC14A is useful to "square up" slow input rise and fall times. Due to hysteresis voltage of the Schmitt trigger, the HC14A finds applications in noisy environments. Features * * * * * * * * Output Drive Capability: 10 LSTTL Loads Outputs Directly Interface to CMOS, NMOS and TTL Operating Voltage Range: 2.0 to 6.0 V Low Input Current: 1.0 mA High Noise Immunity Characteristic of CMOS Devices In Compliance With the JEDEC Standard No. 7.0 A Requirements Chip Complexity: 60 FETs or 15 Equivalent Gates Pb-Free Packages are Available http://onsemi.com MARKING DIAGRAMS 14 PDIP-14 N SUFFIX CASE 646 14 1 MC74HC14AN AWLYYWWG 1 14 SOIC-14 D SUFFIX CASE 751A 14 1 HC14AG AWLYWW 1 14 14 1 TSSOP-14 DT SUFFIX CASE 948G 1 HC 14A ALYWG G 14 14 1 SOEIAJ-14 F SUFFIX CASE 965 74HC14A ALYWG 1 A = Assembly Location L, WL = Wafer Lot Y, YY = Year W, WW = Work Week G or G = Pb-Free Package (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. (c) Semiconductor Components Industries, LLC, 2006 October, 2006 - Rev. 11 1 Publication Order Number: MC74HC14A/D MC74HC14A Pinout: 14-Lead Packages (Top View) VCC A6 Y6 A5 Y5 A4 Y4 14 13 12 11 10 9 8 LOGIC DIAGRAM A1 A2 A3 1 2 3 4 5 6 7 A1 Y1 A2 Y2 A3 Y3 GND A4 FUNCTION TABLE Outputs A Y L H H L 2 3 4 5 6 9 8 11 10 13 12 Y1 Y2 Y3 Y=A A5 Inputs 1 A6 Y4 Pin 14 = VCC Pin 7 = GND Y5 Y6 ORDERING INFORMATION Device Package MC74HC14AN PDIP-14 MC74HC14ANG PDIP-14 (Pb-Free) MC74HC14AD SOIC-14 MC74HC14ADG SOIC-14 (Pb-Free) MC74HC14ADR2 SOIC-14 MC74HC14ADR2G SOIC-14 (Pb-Free) MC74HC14ADT TSSOP-14* MC74HC14ADTG TSSOP-14* MC74HC14ADTR2 TSSOP-14* MC74HC14ADTR2G TSSOP-14* MC74HC14AF SOEIAJ-14 MC74HC14AFG SOEIAJ-14 (Pb-Free) MC74HC14AFEL SOEIAJ-14* MC74HC14AFELG SOEIAJ-14* Shipping 25 Units / Rail 55 Units / Rail 2500 / Tape & Reel 96 Units / Rail 2500 / Tape & Reel 50 Units / Rail 2000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *This package is inherently Pb-Free. http://onsemi.com 2 MC74HC14A IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIII IIIII III IIII IIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIII IIIII III IIII IIIIIIIIIIIIII IIIII III IIII IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII MAXIMUM RATINGS Symbol Parameter Value Unit - 0.5 to + 7.0 V DC Input Voltage (Referenced to GND) - 0.5 to VCC + 0.5 V DC Output Voltage (Referenced to GND) - 0.5 to VCC + 0.5 V VCC DC Supply Voltage (Referenced to GND) Vin Vout Iin DC Input Current, per Pin 20 mA Iout DC Output Current, per Pin 25 mA ICC DC Supply Current, VCC and GND Pins 50 mA PD Power Dissipation in Still Air, 750 500 450 mW Tstg Storage Temperature Range - 65 to + 150 _C TL Lead Temperature, 1 mm from Case for 10 Seconds Plastic DIP, SOIC or TSSOP Package Plastic DIP SOIC Package TSSOP Package This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range GND v (Vin or Vout) v VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. _C 260 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Derating -- Plastic DIP: - 10 mW/_C from 65_ to 125_C SOIC Package: - 7 mW/_C from 65_ to 125_C TSSOP Package: - 6.1 mW/_C from 65_ to 125_C For high frequency or heavy load considerations, see Chapter 2 of the ON Semiconductor High-Speed CMOS Data Book (DL129/D). IIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIII III IIII III IIII IIIIIIIIIIIIII III IIII III IIII IIIIIIIIIIIIIIIIIIIIIIII RECOMMENDED OPERATING CONDITIONS Symbol VCC Vin, Vout Parameter Min DC Supply Voltage (Referenced to GND) Max Unit 2.0 6.0 V 0 VCC V - 55 + 125 _C 0 0 0 No Limit* No Limit* No Limit* ns DC Input Voltage, Output Voltage (Referenced to GND) TA Operating Temperature Range, All Package Types tr, tf Input Rise/Fall Time (Figure 1) VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V *When Vin = 50% VCC, ICC > 1mA http://onsemi.com 3 MC74HC14A DC CHARACTERISTICS (Voltages Referenced to GND) Guaranteed Limit VCC V -55 to 25C 85C 125C Unit Vout = 0.1V |Iout| 20mA 2.0 3.0 4.5 6.0 1.50 2.15 3.15 4.20 1.50 2.15 3.15 4.20 1.50 2.15 3.15 4.20 V Minimum Positive-Going Input Threshold Voltage (Figure 3) Vout = 0.1V |Iout| 20mA 2.0 3.0 4.5 6.0 1.0 1.5 2.3 3.0 0.95 1.45 2.25 2.95 0.95 1.45 2.25 2.95 V VT- max Maximum Negative-Going Input Threshold Voltage (Figure 3) Vout = VCC - 0.1V |Iout| 20mA 2.0 3.0 4.5 6.0 0.9 1.4 2.0 2.6 0.95 1.45 2.05 2.65 0.95 1.45 2.05 2.65 V VT- min Minimum Negative-Going Input Threshold Voltage (Figure 3) Vout = VCC - 0.1V |Iout| 20mA 2.0 3.0 4.5 6.0 0.3 0.5 0.9 1.2 0.3 0.5 0.9 1.2 0.3 0.5 0.9 1.2 V VHmax Note 2 Maximum Hysteresis Voltage (Figure 3) Vout = 0.1V or VCC - 0.1V |Iout| 20mA 2.0 3.0 4.5 6.0 1.20 1.65 2.25 3.00 1.20 1.65 2.25 3.00 1.20 1.65 2.25 3.00 V VHmin Note 2 Minimum Hysteresis Voltage (Figure 3) Vout = 0.1V or VCC - 0.1V |Iout| 20mA 2.0 3.0 4.5 6.0 0.20 0.25 0.40 0.50 0.20 0.25 0.40 0.50 0.20 0.25 0.40 0.50 V VOH Minimum High-Level Output Voltage Vin VT- min |Iout| 20mA 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 1.9 4.4 5.9 V 3.0 4.5 6.0 2.48 3.98 5.48 2.34 3.84 5.34 2.20 3.70 5.20 2.0 4.5 6.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 6.0 0.26 0.26 0.26 0.33 0.33 0.33 0.40 0.40 0.40 Symbol Parameter VT+ max Maximum Positive-Going Input Threshold Voltage (Figure 3) VT+ min Condition Vin VT- min VOL Maximum Low-Level Output Voltage |Iout| 2.4mA |Iout| 4.0mA |Iout| 5.2mA Vin VT+ max |Iout| 20mA Vin VT+ max |Iout| 2.4mA |Iout| 4.0mA |Iout| 5.2mA V Iin Maximum Input Leakage Current Vin = VCC or GND 6.0 0.1 1.0 1.0 mA ICC Maximum Quiescent Supply Current (per Package) Vin = VCC or GND Iout = 0mA 6.0 1.0 10 40 mA 1. Information on typical parametric values along with frequency or heavy load considerations can be found in Chapter 2 of the ON Semiconductor High-Speed CMOS Data Book (DL129/D). 2. VHmin > (VT+ min) - (VT- max); VHmax = (VT+ max) - (VT- min). http://onsemi.com 4 MC74HC14A AC CHARACTERISTICS (CL = 50pF, Input tr = tf = 6ns) Symbol Parameter Guaranteed Limit VCC V -55 to 25C 85C 125C Unit tPLH, tPHL Maximum Propagation Delay, Input A or B to Output Y (Figures 1 and 2) 2.0 3.0 4.5 6.0 75 30 15 13 95 40 19 16 110 55 22 19 ns tTLH, tTHL Maximum Output Transition Time, Any Output (Figures 1 and 2) 2.0 3.0 4.5 6.0 75 27 15 13 95 32 19 16 110 36 22 19 ns 10 10 10 pF Cin Maximum Input Capacitance NOTE: For propagation delays with loads other than 50 pF, and information on typical parametric values, see Chapter 2 of the ON Semiconductor High-Speed CMOS Data Book (DL129/D). Typical @ 25C, VCC = 5.0 V CPD 22 Power Dissipation Capacitance (Per Inverter)* pF * Used to determine the no-load dynamic power consumption: PD = CPD VCC 2 f + ICC VCC . For load considerations, see Chapter 2 of the ON Semiconductor High-Speed CMOS Data Book (DL129/D). tf INPUT A tr VCC 90% 50% 10% GND tPLH tPHL 90% 50% 10% OUTPUT Y tTLH tTHL Figure 1. Switching Waveforms TEST POINT OUTPUT DEVICE UNDER TEST CL* *Includes all probe and jig capacitance Figure 2. Test Circuit http://onsemi.com 5 VT , TYPICAL INPUT THRESHOLD VOLTAGE (VOLTS MC74HC14A 4 3 (VT+) VHtyp 2 (VT-) 1 2 3 4 5 VCC, POWER SUPPLY VOLTAGE (VOLTS) 6 VHtyp = (VT+ typ) - (VT- typ) Figure 3. Typical Input Threshold, VT+, VT- versus Power Supply Voltage A Y (a) A Schmitt-Trigger Squares Up Inputs With Slow Rise and Fall Times VH Vin (b) A Schmitt-Trigger Offers Maximum Noise Immunity VCC VH VT+ VT- Vin VCC VT+ VT- GND GND VOH VOH Vout Vout VOL VOL Figure 4. Typical Schmitt-Trigger Applications http://onsemi.com 6 MC74HC14A PACKAGE DIMENSIONS PDIP-14 CASE 646-06 ISSUE P 14 8 1 7 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. B A F L N C -T- SEATING PLANE H G D 14 PL J K 0.13 (0.005) M M http://onsemi.com 7 DIM A B C D F G H J K L M N INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.290 0.310 --- 10 _ 0.015 0.039 MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.37 7.87 --- 10 _ 0.38 1.01 MC74HC14A PACKAGE DIMENSIONS SOIC-14 CASE 751A-03 ISSUE H NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. -A- 14 8 -B- P 7 PL 0.25 (0.010) M 7 1 G -T- 0.25 (0.010) M T B S A DIM A B C D F G J K M P R J M K D 14 PL F R X 45 _ C SEATING PLANE B M S SOLDERING FOOTPRINT* 7X 7.04 14X 1.52 1 14X 0.58 1.27 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 8 MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 MC74HC14A PACKAGE DIMENSIONS TSSOP-14 CASE 948G-01 ISSUE B 14X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S S N 2X 14 L/2 M B -U- L PIN 1 IDENT. N F 7 1 0.15 (0.006) T U 0.25 (0.010) 8 S DETAIL E CCC CCC EEE CCC EEE K A -V- K1 J J1 SECTION N-N C 0.10 (0.004) -T- SEATING PLANE D H G DETAIL E NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. MILLIMETERS INCHES DIM MIN MAX MIN MAX A 4.90 5.10 0.193 0.200 B 4.30 4.50 0.169 0.177 C --- 1.20 --- 0.047 D 0.05 0.15 0.002 0.006 F 0.50 0.75 0.020 0.030 G 0.65 BSC 0.026 BSC H 0.50 0.60 0.020 0.024 J 0.09 0.20 0.004 0.008 J1 0.09 0.16 0.004 0.006 -W- K 0.19 0.30 0.007 0.012 K1 0.19 0.25 0.007 0.010 L 6.40 BSC 0.252 BSC M 0_ 8_ 0_ 8_ SOLDERING FOOTPRINT* 7.06 1 0.65 PITCH 14X 0.36 14X 1.26 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 9 MC74HC14A PACKAGE DIMENSIONS SOEIAJ-14 CASE 965-01 ISSUE A 14 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). LE 8 Q1 E HE M_ L 7 1 DETAIL P Z D VIEW P A e A1 b 0.13 (0.005) c M 0.10 (0.004) DIM A A1 b c D E e HE 0.50 LE M Q1 Z MILLIMETERS MIN MAX --- 2.05 0.05 0.20 0.35 0.50 0.10 0.20 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --- 1.42 INCHES MIN MAX --- 0.081 0.002 0.008 0.014 0.020 0.004 0.008 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --- 0.056 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 10 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC74HC14A/D