15-21SYGD/S530-E3/TR8 - EVERLIGHT ELECTRONICS

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 1 of 9

Device No:SZDSE-151-004 Prepared date:06-17-2004 Prepared by: xunzhi hu

Technical Data Sheet

1206 Package Chip LEDs

15-21SYGD/S530-E3/TR8

Features

․Package in 8mm tape on 7〞diameter reel.

․Compatible with automatic placement equipment.

․Compatible with infrared and vapor phase reflow

solder process.

․Mono-color type.

․Pb-free.

Descriptions

․The 15-21 SMD Taping is much smaller than lead frame

type components, thus enable smaller board

size, higher packing density, reduced

storage space and finally smaller equipment

to be obtained.

․Besides, lightweight makes them ideal for

miniature applications. etc.

Applications

․Automotive: backlighting in dashboard and switch.

․Telecommunication: indicator and backlighting in

telephone and fax.

․Flat backlight for LCD, switch and symbol.

․General use.

Device Selection Guide

Chip

Material Emitted Color Lens Color

AlGaInP

Super Yellow Green Diffused

EVERLIGHT ELECTRONICS CO.,LTD.

15-21

SYGD/S530-E3/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 2 of 9

Device No:SZDSE-151-004 Prepared date:06-17-2004 Prepared by: xunzhi hu

Package Outline Dimensions

+

-

Polarity

3.2

2.0

1.5

1.1±0.2

0.6

2.0

R0.4

3.2

1.5

For reflow soldering (propose)

1.5± 0.15

Cathode mark

1.5

Note: Tolerances Unless Dimension ±0.1mm , Unit = mm

Absolute Maximum Ratings (Ta=25℃)

EVERLIGHT ELECTRONICS CO.,LTD.

15-21

SYGD/S530-E3/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 3 of 9

Device No:SZDSE-151-004 Prepared date:06-17-2004 Prepared by: xunzhi hu

Parameter Symbol Rating Unit

Reverse Voltage V

R

5 V

Forward Current I

F

25 mA

Operating Temperature Topr -40 ~ +85 ℃

Storage Temperature Tstg -40~ +100 ℃

Soldering Temperature Tsol 260

(for 5 second) ℃

Electrostatic Discharge ESD 2000 V

Power Dissipation Pd 60 mW

Peak Forward Current

(Duty 1/10 @1KHz) I

F P

60 mA

Electro-Optical Characteristics (Ta=25℃)

Parameter

Symbol

Min. Typ. Max. Unit

Condition

Luminous Intensity

Iv

16 22 ----

mcd

Viewing Angle

2θ1/2

----- 150 -----

deg

Peak Wavelength

λp

----- 575 -----

nm

Dominant Wavelength

λd

----- 573 -----

nm

Spectrum Radiation

Bandwidth

△λ

----- 20 -----

nm

Forward Voltage

VF

----- 2.0 2.4

V

I

F

=20mA

Reverse Current IR

----- ----- 10

μA

V

R

=5V

Typical Electro-Optical Characteristics Curves

EVERLIGHT ELECTRONICS CO.,LTD.

15-21

SYGD/S530-E3/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 4 of 9

Device No:SZDSE-151-004 Prepared date:06-17-2004 Prepared by: xunzhi hu

EVERLIGHT ELECTRONICS CO.,LTD.

15-21

SYGD/S530-E3/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 5 of 9

Device No:SZDSE-151-004 Prepared date:06-17-2004 Prepared by: xunzhi hu

Label explanation

CAT: Luminous Intensity Rank

HUE: Dom. Wavelength Rank

REF: Forward Voltage Rank

Reel Dimensions

Note: Tolerances Unless Dimension ±0.1mm , Unit = mm

EVERLIGHT ELECTRONICS CO.,LTD.

15-21

SYGD/S530-E3/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 6 of 9

Device No:SZDSE-151-004 Prepared date:06-17-2004 Prepared by: xunzhi hu

Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel

Note: Tolerances Unless Dimension ±0.1mm , Unit = mm

Moisture Resistant Packaging

Aluminum moistue-proof bag LabelDesiccant

Label

EVERLIGHT ELECTRONICS CO.,LTD.

15-21

SYGD/S530-E3/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 7 of 9

Device No:SZDSE-151-004 Prepared date:06-17-2004 Prepared by: xunzhi hu

Reliability Test Items And Conditions

The reliability of products shall be satisfied with items listed below.

Confidence level：90%

LTPD：10%

No. Items Test Condition

Test

Hours/Cycles Sample

Size Ac/Re

1 Reflow Soldering

Temp. : 260℃±5℃

Min 5 sec. 6 Min. 22 Pcs. 0/1

2 Temperature Cycle

H : +100℃ 15min

∫ 5 min

L : -40℃ 15min

300 Cycles 22 PCS. 0/1

3 Thermal Shock

H : +100℃ 5min

∫ 10 sec

L : -10℃ 5min

300 Cycles 22 PCS. 0/1

4 High Temperature

Storage Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1

5 Low Temperature

Storage Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1

6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1

7 High Temperature /

High Humidity 85℃/85% RH 1000 Hrs. 22 PCS. 0/1

EVERLIGHT ELECTRONICS CO.,LTD.

15-21

SYGD/S530-E3/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 8 of 9

Device No:SZDSE-151-004 Prepared date:06-17-2004 Prepared by: xunzhi hu

Precautions For Use

1. Over-current-proof

Customer must apply resistors for protection , otherwise slight voltage shift will cause big

current change ( Burn out will happen ).

2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 The LEDs should be used within a year.

2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.

2.5 The LEDs should be used within 168 hours (7 days) after opening the package.

2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the

storage time, baking treatment should be performed using the following conditions.

Baking treatment : 60±5℃ for 24 hours.

3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

3.4 After soldering, do not warp the circuit board.

4.Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds

within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do

soldering of each terminal. Be careful because the damage of the product is often started at the time of

the hand solder.

EVERLIGHT ELECTRONICS CO.,LTD.

15-21

SYGD/S530-E3/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 9 of 9

Device No:SZDSE-151-004 Prepared date:06-17-2004 Prepared by: xunzhi hu

5.Repairing

Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a

double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether

the characteristics of the LEDs will or will not be damaged by repairing.

EVERLIGHT ELECTRONICS CO., LTD. Tel: 0512-63409123-1603

Office: No 355,Zhong Shan North Rd ,WuJiang, Fax: 0512-63409123-1510

Economy Development Zone(YunXi Area), http://www.everlight.com

SongLing Town,WuJiang City,JiangSu PRC, China.