ADVANCED LINEAR DEVICES, INC. ALD4704A/ALD4704B ALD4704 QUAD RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER GENERAL DESCRIPTION FEATURES The ALD4704 is a quad CMOS monolithic operational amplifier with MOSFET input that has rail-to-rail input and output voltage ranges. The input voltage can be beyond positive power supply voltage V+ or the negative power supply voltage V- by up to 300mV. The output voltage swings to within 60mV of either positive or negative power supply voltages at rated load. * * * * With high impedance load, the output voltage approaches to within 1mV of the power supply rails. This device is designed as an alternative to the popular J-FET input operational amplifiers in applications where lower operating voltages, such as 9V battery or 3.25V to 6V power supplies are being used. It offers high slew rate of 5V/s at low operating power. The ALD4704 is designed and manufactured with Advanced Linear Devices' standard enhanced ACMOS silicon gate CMOS process for low unit cost and exceptional reliability. * The rail-to-rail input and output feature of the ALD4704 expand signal voltage range for a given operating supply voltage and allow numerous analog serial stages to be implemented without losing operating voltage margin. The output stage is designed to drive up to 10mA into 400pF capacitive and 1.5K resistive loads at unity gain and up to 4000pF at a gain of 5. Short circuit protection to either ground or the power supply rails is at approximately 15mA clamp current. The output can both source and sink 10mA into a load with symmetrical drive and is ideally suited for applications where push-pull voltage drive is desired. For each of the operational amplifier, the offset voltage is trimmed on-chip to eliminate the need for external nulling in many applications. For precision applications, the output is designed to settle to 0.1% in 2s. For large signal buffer applications, the operational amplifier can function as an ultrahigh input impedance voltage follower/buffer that allows input and output voltage swings from positive to negative supply voltages. This feature is intended to greatly simplify systems design and eliminate higher voltage power supplies in many applications. * * * * * * * Rail-to-rail input and output voltage ranges 5.0V/s slew rate Symmetrical push-pull output drive Inputs can extend beyond supply rails by 300mV Outputs settle to 2mV of supply rails High capacitive load capability -- up to 4000pF No frequency compensation required - unity gain stable Extremely low input bias currents -- 1.0pA typical (20pA max.) Ideal for high source impedance applications High voltage gain -- typically 100V/mV Output short circuit protected Unity gain bandwidth of 2.1MHz APPLICATIONS * * * * * * * * * * * * * * * Voltage amplifier Voltage follower/buffer Charge integrator Photodiode amplifier Data acquisition systems High performance portable instruments Signal conditioning circuits Low leakage amplifiers Active filters Sample/Hold amplifier Picoammeter Current to voltage converter Coaxial cable driver Capacitive sensor amplifier Piezoelectric transducer amplifier PIN CONFIGURATION ORDERING INFORMATION Operating Temperature Range* -55C to +125C 0C to +70C 0C to +70C 14-Pin CERDIP Package 14-Pin Small Outline Package (SOIC) 14-Pin Plastic Dip Package ALD4704A DB ALD4704B DB ALD4704 DB ALD4704A SB ALD4704B SB ALD4704 SB ALD4704A PB ALD4704B PB ALD4704 PB * Contact factory for industrial temperature range OUT A 1 14 OUT D -IN A 2 13 -IN D +IN A 3 12 +IN D V+ 4 11 V- +IN B 5 10 +IN C -IN B 6 9 -IN C OUT B 7 8 OUT C DB, PB, SB Package (c) 1998 Advanced Linear Devices, Inc. 415 Tasman Drive, Sunnyvale, California 94089 -1706 Tel: (408) 747-1155 Fax: (408) 747-1286 http://www.aldinc.com ABSOLUTE MAXIMUM RATINGS -0.3V to V++13.2V 6.6V -0.3V to V + +0.3V 600 mW 0C to +70C -55C to +125C -65C to +150C +260C Supply voltage, V+ referenced to VSupply voltage, VS referenced to VDifferential input voltage range Power dissipation Operating temperature range PB, SB package DB package Storage temperature range Lead temperature, 10 seconds OPERATING ELECTRICAL CHARACTERISTICS TA = 25 C VS = 5.0V unless otherwise specified VS V+ Input Offset Voltage VOS Input Offset Current IOS 1.0 15 240 1.0 15 240 Input Bias Current IB 1.0 20 300 1.0 20 300 Input Voltage Range VIR Input Resistance RIN Input Offset Voltage Drift TCV OS Power Supply Rejection Ratio PSRR 65 80 65 80 60 Common Mode Rejection Ratio CMRR 65 83 65 83 Large Signal Voltage Gain AV 15 28 100 15 28 100 Output Voltage Range VO low VO high VO low VO high Output Short Circuit Current ISC 15 Supply Current IS 10 Power Dissipation PD Input Capacitance CIN 1 1 1 Bandwidth BW 2.1 2.1 2.1 MHz Slew Rate SR 5.0 5.0 5.0 V/s AV = +1 RL = 2.0K Rise time tr 0.1 0.1 0.1 s RL = 10K 15 15 15 % RL = 10K CL = 100pF ALD4704A/ALD4704B ALD4704 Min 6.0 3.25 12.0 6.5 5.3 Unit Test Conditions V V Dual Supply Single Supply 5.0 6.0 mV mV RS 100K 0C TA +70C 1.0 15 240 pA pA TA = 25C 0C TA +70C 1.0 20 300 pA pA TA = 25C 0C TA +70C 5.3 V 6.0 3.25 12.0 6.5 1.0 1.5 -5.3 Min 4704 Typ Supply Voltage 3.25 6.5 Max 4704B Typ Max Symbol Overshoot Factor Min 4704A Typ Parameter 6.0 12.0 2.0 3.0 -5.3 5.3 -5.3 10 12 1012 1012 5 5 5 -4.96 4.95 -4.998 4.99 4.998 -4.90 4.90 -4.96 -4.90 4.95 -4.998 -4.99 4.99 4.998 4.90 -4.99 10 130 V/C RS 100K 80 dB RS 100K 0C TA +70C 60 83 dB RS 100K 0C TA +70C 10 28 100 V/mV V/mV V/mV RL = 100K RL 1M RL = 10K V V V V RL = 10K 0C TA +70C RL 1M 0C TA +70C -4.96 4.95 -4.998 4.99 4.998 -4.90 4.90 15 13 Max -4.99 15 13 10 130 Advanced Linear Devices mA 13 mA VIN = -5.0V No Load 130 mW All amplifiers, No Load VS = 5.0V pF 2 OPERATING ELECTRICAL CHARACTERISTICS (cont'd) TA = 25C VS = 5.0V unless otherwise specified 4704A Typ Max Min Typ 4704 Symbol Maximum Load Capacitance CL 400 4000 400 4000 400 4000 Input Noise Voltage en 26 26 Input Current Noise in 0.6 ts 5.0 2.0 Settling Time Min 4704B Parameter Max Min Typ Max Unit Test Conditions pF pF Gain = 1 Gain = 5 26 nV/Hz f =1KHz 0.6 0.6 fA/Hz f =10Hz 5.0 2.0 5.0 2.0 s s 0.01% 0.1% AV = -1 RL = 5K CL= 50pF VS = 5.0V -55C TA +125C unless otherwise specified 4704DB Typ Max Unit 4.0 7.0 mV 8.0 8.0 8.0 nA 10.0 10.0 10.0 nA Min 4704B DB Typ Max Symbol Input Offset Voltage VOS 2.0 Input Offset Current IOS Input Bias Current IB Power Supply Rejection Ratio PSRR 60 75 60 75 60 75 dB RS 100K Common Mode Rejection Ratio CMRR 60 83 60 83 60 83 dB RS 100K Large Signal Voltage Gain AV 10 25 10 25 10 25 V/mV RL =10K Output Voltage Range VO low VO high 4.8 -4.9 4.9 4.8 -4.9 4.9 4.8 -4.9 4.9 V V RL =10K RL =10K ALD4704A/ALD4704B ALD4704 Min 4704A DB Typ Max Parameter -4.8 Min -4.8 Advanced Linear Devices -4.8 Test Conditions RS 100K 3 Design & Operating Notes: 1. The ALD4704 CMOS operational amplifier uses a 3 gain stage architecture and an improved frequency compensation scheme to achieve large voltage gain, high output driving capability, and better frequency stability. The ALD4704 is internally compensated for unity gain stability using a novel scheme. This design produces a clean single pole roll off in the gain characteristics while providing for more than 70 degrees of phase margin at the unity gain frequency. A unity gain buffer using the ALD4704 will typically drive 400pF of external load capacitance without stability problems. In the inverting unity gain configuration, it can drive up to 800pF of load capacitance. Compared to other CMOS operational amplifiers, the ALD4704 is much more resistant to parasitic oscillations. 2. The ALD4704 has complementary p-channel and n-channel input differential stages connected in parallel to accomplish rail to rail input common mode voltage range. With the common mode input voltage close to the power supplies, one of the two differential stages is switched off internally. To maintain compatibility with other operational amplifiers, this switching point has been selected to be about 1.5V above the negative supply voltage. As offset voltage trimming on the ALD4704 is made when the input voltage is symmetrical to the supply voltages, this internal switching does not affect a large variety of applications such as an inverting amplifier or non-inverting amplifier with a gain greater than 2.5 (5V operation), where the common mode voltage does not make excursions below this switching point. 3. The input bias and offset currents are essentially input protection diode reverse bias leakage currents, and are typically less than 1pA at room temperature. This low input bias current assures that the analog signal from the source will not be distorted by input bias currents. For applications where source impedance is very high, it may be necessary to limit noise and hum pickup through proper shielding. 4. The output stage consists of class AB complementary output drivers, capable of driving a low resistance load. The output voltage swing is limited by the drain to source on-resistance of the output transistors as determined by the bias circuitry, and the value of the load resistor when connected. In the voltage follower configuration, the oscillation resistant feature, combined with the rail to rail input and output feature, makes the ALD4704 an effective analog signal buffer for medium to high source impedance sensors, transducers, and other circuit networks. 5. The ALD4704 operational amplifier has been designed with static discharge protection and to minimize latch up. However, care must be exercised when handling the device to avoid strong static fields. In using the operational amplifier, the user is advised to power up the circuit before, or simultaneously with, any input voltages applied and to limit input voltages to not exceed 0.3V of the power supply voltage levels. Alternatively, a 100K or higher value resistor at the input terminals will limit input currents to acceptable levels while causing very small or negligible accuracy effects. TYPICAL PERFORMANCE CHARACTERISTICS COMMON MODE INPUT VOLTAGE RANGE AS A FUNCTION OF SUPPLY VOLTAGE OPEN LOOP VOLTAGE GAIN AS A FUNCTION OF SUPPLY VOLTAGE AND TEMPERATURE 7 1000 } -55C OPEN LOOP VOLTAGE GAIN (V/mV) COMMON MODE INPUT VOLTAGE RANGE (V) TA = 25C 6 5 4 3 2 3 2 4 } +25C 100 } +125C 10 RL= 10K RL= 5K 1 5 6 7 2 0 SUPPLY VOLTAGE (V) INPUT BIAS CURRENT AS A FUNCTION OF AMBIENT TEMPERATURE 16 VS = 5.0V SUPPLY CURRENT (mA) INPUT BIAS CURRENT (pA) 6 8 SUPPLY CURRENT AS A FUNCTION OF SUPPLY VOLTAGE 10000 1000 4 SUPPLY VOLTAGE (V) 100 10 1.0 INPUTS GROUNDED OUTPUT UNLOADED 14 12 10 TA = -55C -25C +25C +80C +125C 8 6 4 2 0 0.1 -50 -25 0 25 50 75 100 0 125 AMBIENT TEMPERATURE (C) ALD4704A/ALD4704B ALD4704 1 2 3 4 5 6 7 SUPPLY VOLTAGE (V) Advanced Linear Devices 4 TYPICAL PERFORMANCE CHARACTERISTICS 120 100 6 OPEN LOOP VOLTAGE GAIN (dB) 25C TA 125C RL = 10K RL = 10K 5 4 RL = 2K 3 2 60 0 40 45 20 90 0 135 180 -20 0 1 2 3 4 5 6 7 1 10 100 1K 10K 100K 1M 10M SUPPLY VOLTAGE (V) FREQUENCY (Hz) INPUT OFFSET VOLTAGE AS A FUNCTION OF AMBIENT TEMPERATURE REPRESENTATIVE UNITS INPUT OFFSET VOLTAGE AS A FUNCTION OF COMMON MODE INPUT VOLTAGE INPUT OFFSET VOLTAGE (mV) 15 +5 +4 VS = 5.0V +3 +2 +1 0 -1 -2 -3 -4 VS = 5.0V TA = 25C 10 5 0 -5 -10 -15 -5 -50 -25 0 +25 +50 +75 +100 +125 -4 -2 0 +2 +4 +6 AMBIENT TEMPERATURE (C) COMMON MODE INPUT VOLTAGE (V) OPEN LOOP VOLTAGE GAIN AS A FUNCTION OF LOAD RESISTANCE VOLTAGE NOISE DENSITY AS A FUNCTION OF FREQUENCY 1000 150 VOLTAGE NOISE DENSITY (nV/ Hz) OPEN LOOP VOLTAGE GAIN (V/mV) VS = 5.0V TA = 25C 80 PHASE SHIFT IN DEGREES OUTPUT VOLTAGE SWING (V) 7 INPUT OFFSET VOLTAGE (mV) OPEN LOOP VOLTAGE AS A FUNCTION OF FREQUENCY OUTPUT VOLTAGE SWING AS A FUNCTION OF SUPPLY VOLTAGE 100 VS = 5.0V TA = 25C 10 1 125 VS = 5.0V TA = 25C 100 75 50 25 0 1K 10K 100K 1000K 10 100 LOAD RESISTANCE () LARGE - SIGNAL TRANSIENT RESPONSE 5V/div 5V/div ALD4704A/ALD4704B ALD4704 1K 10K 100K 1000K FREQUENCY (Hz) SMALL - SIGNAL TRANSIENT RESPONSE VS = 5.0V TA = 25C RL = 1K CL = 50pF 100mV/div 2s/div 50mV/div Advanced Linear Devices VS = 5.0V TA = 25C RL = 1.0K CL = 50pF 1s/div 5 TYPICAL APPLICATIONS RAIL-TO-RAIL VOLTAGE FOLLOWER/BUFFER RAIL-TO-RAIL VOLTAGE COMPARATOR +12V +10V = 1012 ZIN ~ 0.1F VIN CL + VIN VOUT VOUT RL 1.5K 400pF 0 VIN 10V 0.1F - +12V + 50K 10M LOW OFFSET SUMMING AMPLIFIER 10K 50K +5V INPUT 1 PHOTO DETECTOR CURRENT TO VOLTAGE CONVERTER RF = 5M 0.1F I - INPUT 2 10K VOUT GAIN = 5 + CL = 4000pF * Circuit Drives Large Load Capacitance 4000pF + -5V 0.1F WIEN BRIDGE OSCILLATOR (RAIL-TO -RAIL) SINE WAVE GENERATOR ~ f= V OUT 10K + -5V 10K 1 ~ 1.6K Hz = 2RC LOW PASS FILTER (RFI FILTER) RF VIN 5K 5K R1 R1 C1 +5V 1 M VIN 10K -5V .01F R = 10K C = .01F BANDPASS NETWORK 100K C2 +9V R2 - 0.02F C1 VOUT + R1 VIN - 1 = 3.2kHz R1C1 Gain = 10 Frequency roll-off 20dB/decade ALD4704A/ALD4704B ALD4704 +5V VOUT + Cutoff frequency = RL 1.5K -5V 1000 pF VOUT + VOUT = 1 X RF PRECISION CHARGE INTEGRATOR +5V - +5V PHOTODIODE Low Frequency Breakpoint L = 1 = 160Hz 2 R1C1 High Frequency Cutoff H = Advanced Linear Devices 1 = 32KHz 2 R2 C2 -5V R1 = 10K C1 = 100nF R2 = 10K C2 = 500pF 6