Advanced Analog Technology, Inc. AAT1015 Details are subject to change without notice 3-CHANNEL PC POWER SUPPLY SUPERVISOR GENERAL DESCRIPTION FEATURES z 3-Channel PC Power Supply Supervisor z Over Voltage Protection for 3.3V, 5V, 12V Output z Under Voltage Protection for 3.3V, 5V Output with 75 ms Enable Delay z Fault Protection Output with Open Drain Output z Open Drain Power Good Output z 300 ms Power Good Delay z 2.3 ms ONCTL to FPO Turn Off Delay z 38 ms ONCTL Signal De-Bounce z 73 s De-Bounce z Latch Function Controlled by ONCTL and Protection Input. PIN CONFIGURATION TOP VIEW PGI 1 8 PGO GND 2 7 Vcc FPO 3 6 V5 ONCTL 4 5 V33 The AAT1015 is a 3-channel PC switching power supply supervisor that provides Over Voltage Protection (OVP), Under Voltage Protection (UVP), and Power Good Indicator to monitor and control the output of the switching power supply system. In addition to the implemented remote function from external signal, i.e., On/Off Control ( ONCTL ), over voltage fault protection and under voltage fault protection can also be directly triggered without external voltage divider. AAT1015 also greatly reduce the PCB board space for power supply system. With a minimal number of external components, the AAT1015 offers a simple and cost effective solution. (PDIP-8 PACKAGE) - - - Advanced Analog Technology, Inc. - Page 1 of 11 V 1.0 Advanced Analog Technology, Inc. AAT1015 FPO (Fault Protection Output) NORMAL="LOW", FAULT="HIGH" FPO indicates the fault condition of either Over Voltage or Under Voltage. When a fault state occurs, the FPO would be latched high and combined with a low PGO output. PGO (Power Good Output) NORMAL="HIGH", FAULT="LOW". A Power Good signal will be issued with 300 ms delay after 3.3V, 5V, 12V and PGI are ready. Power Good Output should be low before the output voltage is out of regulation at turn-off. OVP and UVP (Over Voltage Protection and Under Voltage Protection) OVP monitors 3.3V, 5V, and 12V via VCC pin, while UVP monitors 3.3V and 5V. OVP and UVP levels are determined by internal voltage dividers. The typical values are 3.9V, 6.1V, 13.8V for OVP and 2.2V, 3.5V for UVP, respectively. ONCTL (On/Off Control) On/Off Control is used to reset the latched state of FPO and to externally control the switching power supply system with a 38 ms de-bounce time. AAT1015 offers 2.3 ms delay time after de-bounce to trigger FPO when ONCTL switches from low to high - - - Advanced Analog Technology, Inc. - Page 2 of 11 V 1.0 Advanced Analog Technology, Inc. AAT1015 PIN DESCRIPTION Pin No Name 1 PGI 2 GND 3 FPO 4 ONCTL 5 V33 6 V5 7 VCC 8 PGO I/O Description I Power Good Input Signal Ground O Inverted Fault Protection Output, Open Drain Output Stage I ON/OFF Control Input I Over and Under Voltage Protection for 3.3V I Over and Under Voltage Protection for 5V I Supply Voltage and 12V Over Voltage Protection Input O Power Good Output Signal; Open Drain Output Stage ABSOLUTE MAXIMUM RATINGS Characteristics Symbol VCC Value Unit 16 V FPO Output Voltage VFPO 16 V PGO Output Voltage VPGO 8 V Supply Current I CC 1 mA Operating Free-Air Temperature Range TC - 20 to +85 o Tstorage - 45 to +125 o Supply Voltage Storage Temperature Range C C RECOMMENDED OPERATING CONDITIONS Test Condition Supply Voltage, VCC Min Typ Max 4 Input Voltage, VI 15 V ONCTL , V5, V33, PGI VFPO 7 V 15 V VPGO 7 V I FPO 30 mA I PGO 10 mA Output Voltage Output Sink Current, I O (Sink) Unit Supply Voltage Rising Time, t r See Note 1 1 ms Note 1: VCC slew rate must be less than 14 V/ms. - - - Advanced Analog Technology, Inc. - Page 3 of 11 V 1.0 Advanced Analog Technology, Inc. AAT1015 ELECTRICAL CHARACTERISTICS, VCC = 5 V (UNLESS OTHERWISE SPECIFIED) Over Voltage Protection and Under Voltage Protection Parameter Test Condition V33 V5 VCC V33 V5 VCC Over Voltage Threshold Under-Voltage Threshold Min Typ Max Unit 3.7 5.7 13.2 2.0 3.3 3.9 6.1 13.8 2.2 3.5 3.8 4.1 6.5 14.4 2.4 3.7 V Min Typ Max Unit 5 A 0.4 V 5 A V PGO and FPO Parameter I LKG Leakage Current (PGO) Test Condition PGO = 5 V VOL Low Level Output Voltage I sin k = 10 mA (PGO) I LKG Leakage Current ( FPO ) V( FPO ) = 5 V Low Level Output Voltage I sin k = 10 mA VOL ( FPO ) I sin k = 30 mA 0.3 0.7 V PGI and ONCTL Parameter Test Condition Input Threshold Voltage (PGI) Input Pull-Up Current ( ONCTL ) ONCTL = 0 V High-Level Input Voltage ( ONCTL ) Low-Level Input Voltage ( ONCTL ) Min Typ Max Unit 1.10 1.15 150 1.20 V A 2.0 V 0.8 V - - - Advanced Analog Technology, Inc. - Page 4 of 11 V 1.0 Advanced Analog Technology, Inc. AAT1015 ELECTRICAL CHARACTERISTICS, VCC = 5 V (UNLESS OTHERWISE SPECIFIED) Operating Current Parameter I CC Supply Current Test Condition Min Typ ONCTL = 5 V Max Unit 1 mA Switching Characteristics, VCC = 5V, Top = Full Range Parameter Test Condition t d1 PGO Delay Time t d 2 Under Voltage Protection Delay Time t d 3 ONCTL Off to FPO Delay Min Typ Max Unit 200 300 450 ms 49 75 114 ms t b1 +1.1 t b1 +2.3 t b1 +4.4 ms t b1 ONCTL De-Bounce Time t b 2 Noise De-Bounce Time 24 38 57 47 73 110 ms s - - - Advanced Analog Technology, Inc. - Page 5 of 11 V 1.0 Advanced Analog Technology, Inc. AAT1015 BLOCK DIAGRAM V cc UVLO P ow er o n R eset V IN T O V 12 GND R eset V I N T = 3 .5 8 V FPO L ev el S h ift V ref R O V 12 POD 73 s D eboun ce V ref OV5 S R R e se t R V ref PO D2 S Q Q R O V 33 V5 UV5 OV5 U V 33 O V 33 75 m s D e la y R V 33 V ref PGO L ev el S h ift 73 s D eb ou nce R R UV5 Q POD 73 s D eb ou nce V ref U V 33 CLR 300 m s D e la y V ref PGI R e se t POD2 P O D O sc illa to r V cc 150 uA ONCTL R e se t 38 m s D ebounce 2 .3 m s C L R D e la y V B G = 1 .2 8 POD B andgap R e fe r e n c e - - - Advanced Analog Technology, Inc. - Page 6 of 11 V 1.0 Advanced Analog Technology, Inc. AAT1015 TIMING CHART V cc R eset R ONCTL S Q FP O PG I 3.3 V 5V 12 V PG O t d1 t d1 t b1 P rotection O ccur t d1 t b1 t d3 PG O FF delay ONCTL OFF ONCTL ON AC O FF - - - Advanced Analog Technology, Inc. - Page 7 of 11 V 1.0 Advanced Analog Technology, Inc. AAT1015 PACKAGE DIMENSION - - - Advanced Analog Technology, Inc. - Page 8 of 11 V 1.0 Advanced Analog Technology, Inc. AAT1015 PACKAGE DIMENSION (CONT.) SYMBOL A A1 A2 B B1 B2 C D E E1 e L eB S DIMENSION IN MILLIMETERS MIN TYP MAX 3.6 3.9 4.2 0.38 --------3.25 3.30 3.45 0.36 0.46 0.56 1.400 1.524 1.650 0.813 0.990 1.170 0.20 0.25 0.33 9.12 9.30 9.53 7.62 7.87 8.26 6.20 6.35 6.60 ----2.54 ----3.18 --------8.38 ----9.40 0.71 0.84 0.97 MIN 0.142 0.015 0.128 0.014 0.055 0.032 0.008 0.359 0.300 0.244 ----0.125 0.330 0.028 DIMENSION IN INCHES TYP 0.154 ----0.130 0.018 0.060 0.039 0.010 0.366 0.310 0.250 0.100 --------0.033 MAX 0.165 ----0.136 0.022 0.065 0.046 0.013 0.375 0.325 0.260 --------0.370 0.038 NOTES: 1. CONTROLLING DIMENSION: INCH. 2. LEAD FRAM MATERIAL: C194. 3. PACKAGE DIMENSION EXCLUDE MOLDING FLASH. 4. AFTER SOLDER PLATING, LEAD THICKNESS WILL BE 0.013" MAX. 5. AFTER SOLDER DIPPING, LEAD THICKNESS WILL BE 0.020" MAX. 6. THE MAX. ALLOWABLE MOLDING FLASH IS 0.010". 7. TOLERANCE: 0.010" UNLESS OTERWISE SPECIFIED. 8. OTHERWISE DIMENSION FOLLOW ACCEPTABLE SPECS. 9. THE BOTTOM E - PIN INDENT IS MARKED AS BELOW. 10. PACKAGE DIMENSION IS IN COMPLIANCE WITH JEDEC STANDARD MS-001 AB JUL85' ISSUE B. - - - Advanced Analog Technology, Inc. - Page 9 of 11 V 1.0 Advanced Analog Technology, Inc. AAT1015 TAPE AND REEL PACKING METHOD: 60PCS/TUBE, 3,000PCS/BOX, 12,000PCS/CARTON POSITION OF THE PRODUCT INSIDE OF THE PLASTIC TUDE NOTE: 60PCS/TUBE AE TUBES ARE PLACED IN SMALL PAPER BOXES, WITH THE WHITE PLUG FACING THE SIDE WITH MARKING NOTE: 50TUBES/B MARKING FOR THE SMALL PAPER BOX SHOULD BE POSITIONED AS SHOWN ABOVE NOTE: USE CLEAR TAPE TO SEAL THE SMALL BOX INSTEAD OF QA SEAL AEPOSITION LABEL ON THE RIGHT CORNER OF THE BLANK BOXES MARKING ON THE LARGE BOX AS SHOWN ABOVE NOTE: 4 SMALL BOXES/LARGE BOX, WITH NO QA SEAL - - - Advanced Analog Technology, Inc. - Page 10 of 11 V 1.0 Advanced Analog Technology, Inc. AAT1015 PART MARKING PDIP8 TOP MARKING AAT1015 BXXXXX.X YYWW TAIWAN (LOT NO.) (DATE CODE: 0416->2004, WEEK 16) NOTE: PDIP8 HAS NO BACK MARKING. - - - Advanced Analog Technology, Inc. - Page 11 of 11 V 1.0