Vectron International 267 Lowell Road, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com
VCC6-L
3.3 volt LVDS Oscillator, >270MHz
The VCC6 Crystal Oscillator
Features
3.3 V LVDS
Output frequencies from 270-800 MHz
Enable/Disable output for test and board
debug
-10/70 or –40/85 °C operating temperature
Hermetically sealed ceramic SMD package
Product is compliant to RoHS directive
and fully compatible with lead free assembly
Applications
SONET/SDH/DWDM
Ethernet, Gigabit Ethernet
Storage Area Network
Digital Video
Broadband Access
Description
Vectron’s VCC6 Crystal Oscillator (XO) is quartz
stabilized square wave generator with a LVDS
output, operating off a 3.3 volt supply.
fo
fo
Output
Buffer /
Disable
VCC6-L Output Frequencies > 270MHz
Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com
Performance Characteristics
Table 1. Electrical Performance
Parameter Symbol Min Typical Maximum Units
Frequency fO 270 800 MHz
Supply Voltage 1 VDD 3.15 3.3 3.45
Supply Current, Output Enabled IDD 80 mA
Supply Current, Output Disabled IDD 10 uA
Output Logic Levels
Output Logic High2
Output Logic Low2
VOH
VOL
0.9
1.40
1.10
1.6
V
V
Differential Output VOD 247 330 454 mV
Differential Output Error 50 mV
Differential Output Skew 200 ps
Load (differential) 100 ohms
Offset Voltage VOS 1.125 1.25 1.375 V
Offset Error VOS 25 mV
Output Leakage Current ±10 uA
Transition Times
Rise Time2
Fall Time2
tR
tF
600
600
ps
ps
Symmetry or Duty Cycle3 SYM 45 50 55 %
Operating temperature (ordering option) -10/70 or –40/85 °C
Stability (ordering option)4 ±25, ±50 or ±100 ppm
RMS Jitter, 12kHz to 20 MHz 2 ps
Period RMS Jitter
Period P/P Jitter 4
30 ps
ps
Output Enabled5 0.7*VDD V
Output Disabled5 0.3*VDD V
Output Enable/Disable time 400 nS
Package Size 5.0 x 7.0 x 1.5 mm
1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.
2. Figure 1 defines these parameters.
3. Symmetry is measured defined as On Time/Period.
4. Includes calibration tolerance, operating temperature, supply voltage variations, aging (40 degreesC/10 years) and shock and
vibration (not under operation).
5. Output will be enabled if enable/disable is left open.
Figure 1. Output Waveform
80%
Vs
20%
tF
tR
Period
On Time
VCC6-L Output Frequencies > 270MHz
Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com
Outline Diagram, Pad Layout and Pin Out
Contact Pad Plating: gold over nickel
Table 2. VCC6-LCx Pinout
Pin # Symbol Function
1 E/D Tristate Function
2 NC This pin has no internal connection and is floating.
3 GND Ground
4 fO Output Frequency
5 Cfo Complementary Output Frequency
6 VDD Supply Voltage
Table 3. VCC6-LAx Pinout
Pin # Symbol Function
1 NC This pin has no internal connection and is floating.
2 ED Tristate Function
3 GND Ground
4 fO Output Frequency
5 Cfo Complementary Output Frequency
6 VDD Supply Voltage
VCC6-L Output Frequencies > 270MHz
Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com
A
E
C
D
B
GFJ
LI
KH
Tape and Reel
Table 4. Tape and Reel Dimensions (mm)
Tape Dimensions Reel Dimensions # Per
Product A B C D E F G H I J K L Reel
VCC6 16 7.5 1.5 4 8 2 21 13 60 2 17 180 250
Enable/Disable Functional Description
Under normal operation the Enable/Disable is left open, or set to a logic high state, and the VCC6 is an
oscillation mode with active outputs. When the E/D is set to a logic low, the oscillator stops and the both
the output and complementary output are in a high impedance state. This helps facilitate board testing
and troubleshooting.
Absolute Ratings
Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional
operation is not implied at these or any other conditions in excess of conditions represented in the
operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may
adversely affect device reliability.
Table 5. Absolute Maximum Ratings
Parameter Symbol Ratings Unit
Power Supply VDD -0.5 to +4.6 Vdc
Enable/Disable VIN -0.5 to VDD+0.5 Vdc
Storage Temperature Tstorage -55/125 °C
VCC6-L Output Frequencies > 270MHz
Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com
Reliability
The VCC6 qualification tests include the following:
Table 6. Environnemental Compliance
Parameter Conditions
Mechanical Shock MIL-STD-883 Method 2002
Mechanical Vibration MIL-STD-883 Method 2007
Solderability MIL-STD-883 Method 2003
Gross and Fine Leak MIL-STD-883 Method 1014
Resistance to Solvents MIL-STD-883 Method 2016
Moisture Sensitivity Level MSL1
Handling Precautions
Although ESD protection circuitry has been designed into the the VCC6, proper precautions should be
taken when handling and mounting. VI employs a Human Body Model and a Charged-Device Model
(CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on
the circuit parameters used to define the model. Although no industry wide standard has been adopted
for the CDM, a standard HBM of resistance = 1.5kohms and capacitance = 100pF is widely used and
therefore can be used for comparison purposes.
Table 7. ESD Ratings
Model Minimum Conditions
Human Body Model 1000 MIL-STD-883 Method 3115
Charged Device Model 1000 JESD 22-C101
Suggested IR profile
Table 8 shows max temperatures and lower temperatures can also be used e.g. peak temperature of
220C.
Termination finish is gold over nickel. The VCC6 is hermetically sealed so an aqueous wash is not an
issue.
Table 8. Reflow Profile
Parameter Symbol Value
PreHeat Time t S 60 sec Min, 180 sec Max
Ramp Up R UP 3
oC/sec Max
Time Above 217 oC t L 60 sec Min, 150 sec Max
Time To Peak Temperature t AMB-P 480 sec Max
Time At 260 oC (max) t P 15 sec Max
Ramp Down R DN 6
oC/sec Max
VCC6-L Output Frequencies > 270MHz
Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com
Frequencies (MHz)
311.040 312.500 320.000 322.2656 332.000
333.000 350.000 400.000 446.000 472.000
500.000 600.000 622.080 625.000 644.5313
666.5413 669.3236 693.3265 693.4829 693.750
700.000 779.5686
Other frequencies may be available upon request. Standard frequencies are frequencies which the
crystal has been designed and does not imply a stock position.
Ordering Information
VCC6-LCB 622M080
Product Family Frequency
Crystal Oscillator example: 622M080= 622.080 MHz
Output Stability Options/Temperature
L: LVDS 3.3 Volts A: ±100ppm -10 to 70°C
B: ±50ppm -10 to 70°C
Enable/Disable C: ±100ppm -40 to 85°C
A: E/D is on Pin 2, Pin 1 is a NC D: ±50ppm -40 to 85°C
C: E/D is on Pin 1, Pin 2 is a NC E: ±25ppm -10 to 70°C
F: ±25ppm -40 to 85°C
NOTE: Not all combinations are available.
A ±20ppm over -10 to 70°C, +3.3V, E/D on pin 1, VCC6-109-frequency, is available.
www.vectron.com
Vectron International reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed
as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
VCC6-L >270MHz (REVISION DATE: February 23, 2008
)
For Additional Information, Please Contact:
USA: Vectron International 267 Lowell Road, Hudson, NH 03051
Tel: 1-88-VECTRON-1 Fax: 1-888-FAX-VECTRON
EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany
Tel: 49 (0) 7268 8010 Fax: 49 (0) 7268 801281
ASIA: Vectron Asia Pacific Sales 1F~2F. No.8 Workshop No.308 Fenju Rd., WaiGaoQiao Free
Trade Zone, Pudong New Area Shanghai, China 200131
•Tel: 8621 50480777 • Fax: 8621 50481881