DS91D180/DS91C180 100 MHz M-LVDS Line Driver/Receiver Pair 1 receiver input with no offset.The DS91C180 device has a type 2 receiver input which enable failsafe functionality. General Description The DS91D180 and DS91C180 are 100 MHz M-LVDS (Multipoint Low Voltage Differential Signaling) line driver/receiver pairs designed for applications that utilize multipoint networks (e.g. clock distribution in ATCA and uTCA based systems). M-LVDS is a new bus interface standard (TIA/EIA-899) optimized for multidrop networks. Controlled edge rates, tight input receiver thresholds and increased drive strength are sone of the key enhancments that make M-LVDS devices an ideal choice for distributing signals via multipoint networks. The DS91D180/DS91C180 driver input accepts LVTTL/LVCMOS signals and converts them to differential MLVDS signal levels. The DS91D180/DS91C180 receiver accepts low voltage differential signals (LVDS, B-LVDS, MLVDS, LV-PECL and CML) and converts them to 3V LVCMOS signals. The DS91D180 device has a M-LVDS type Features DC to 100+ MHz / 200+ Mbps low power, low EMI operation Optimal for ATCA, uTCA clock distribution networks Meets or exceeds TIA/EIA-899 M-LVDS Standard Wide Input Common Mode Voltage for Increased Noise Immunity DS91D180 has type 1 receiver input DS91C180 has type 2 receiver input for fail-safe functionality Industrial temperature range Space saving SOIC-14 package (JEDEC MS-012) Typical Application in an ATCA Clock Distribution Network 20041930 (c) 2009 National Semiconductor Corporation 200419 www.national.com DS91D180/DS91C180 100 MHz M-LVDS Line Driver/Receiver Pair November 9, 2009 DS91D180/DS91C180 Connection Diagram Logic Diagram 20041926 Top View Order Number DS91D180TMA, DS91C180TMA See NS Package Number M14A 20041925 Ordering Information Order Number Receiver Input Function Package Type DS91D180TMA DS91C180TMA type 1 Data (0V threshold receiver) SOIC/M14A type 2 Control (offset fail-safe receiver) SOIC/M14A M-LVDS Receiver Types The EIA/TIA-899 M-LVDS standard specifies two different types of receiver input stages. A type 1 receiver has a conventional threshold that is centered at the midpoint of the input amplitude, VID/2. A type 2 receiver has a built in offset that is 100mV greater than VID/2. The type 2 receiver offset acts as a failsafe circuit where open or short circuits at the input will always result in the output stage being driven to a low logic state. 20041940 FIGURE 1. M-LVDS Receiver Input Thresholds www.national.com 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. (CDM 0, 0pF) Recommended Operating Conditions Supply Voltage, VCC Voltage at Any Bus Terminal Min Typ Max Units 3.0 3.3 3.6 V -1.4 +3.8 V (Separate or Common-Mode) Differential Input Voltage VID High Level Input Voltage VIH 2.0 Low Level Input Voltage VIL 0 Operating Free Air Temperature TA -40 113.7 C/W JC Maximum Junction Temperature Storage Temperature Range 5 kV 250 V 1000 V (EIAJ 0, 200pF) Supply Voltage, VCC -0.3V to +4V Control Input Voltages -0.3V to (VCC + 0.3V) Driver Input Voltage -0.3V to (VCC + 0.3V) Driver Output Voltages -1.8V to +4.1V Receiver Input Voltages -1.8V to +4.1V Receiver Output Voltage -0.3V to (VCC + 0.3V) Maximum Package Power Dissipation at +25C SOIC Package 1.1 W Derate SOIC Package 8.8 mW/C above +25C Thermal Resistance (4-Layer, 2 oz. Cu, JEDEC) JA 260C 36.9 C/W 150C -65C to +150C +25 2.4 VCC 0.8 V V V +85 C Electrical Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. (Note 2, Note 3, Note 4, Note 8) Symbol Parameter Conditions Min Typ Max Units 650 mV M-LVDS Driver |VYZ| Differential output voltage magnitude RL = 50, CL = 5pF VYZ Change in differential output voltage magnitude between logic states Figure 2 and Figure 4 VOS(SS) Steady-state common-mode output voltage RL = 50, CL = 5pF |VOS(SS)| Change in steady-state common-mode output voltage between logic states Figure 2 and Figure 3 VOS(PP) Peak-to-peak common-mode output voltage (VOS(pp) @ 500KHz clock) VY(OC) Maximum steady-state open-circuit output voltage Figure 5 VZ(OC) Maximum steady-state open-circuit output voltage VP(H) Voltage overshoot, low-to-high level output VP(L) Voltage overshoot, high-to-low level output 480 -50 0 +50 mV 0.3 1.8 2.1 V +50 mV 0 143 RL = 50, CL = 5pF, CD = 0.5pF Figure 7 and Figure 8 (Note 9) mV 0 2.4 V 0 2.4 V 1.2VSS V -0.2VS V S IIH High-level input current (LVTTL inputs) VIH = 2.0V -15 15 A IIL Low-level input current (LVTTL inputs) VIL = 0.8V -15 15 A VIKL Input Clamp Voltage (LVTTL inputs) IIN = -18 mA -1.5 IOS Differential short-circuit output current Figure 6 -43 43 mA 20 50 mV 94 150 mV V M-LVDS Receiver VIT+ Positive-going differential input voltage threshold See Function Tables VIT- Negative-going differential input voltage threshold See Function Tables Type 1 Type 2 VOH High-level output voltage IOH = -8mA VOL Low-level output voltage IOL = 8mA IOZ TRI-STATE output current VO = 0V or 3.6V IOSR Short circuit Rrceiver output current (LVTTL Output) VO = 0V 3 Type 1 -50 20 mV Type 2 50 94 mV 2.4 2.7 0.28 -10 -90 V 0.4 10 -48 V A mA www.national.com DS91D180/DS91C180 Lead Temperature (Soldering, 4 seconds) ESD Ratings: (HBM 1.5k, 100pF) Absolute Maximum Ratings (Note 1) DS91D180/DS91C180 Symbol Parameter Conditions Min Typ Max Units 32 A +20 A M-LVDS Bus (Input and Output) Pins IA, IY IB, IZ Receiver input or driver high-impedance output current Receiver input or driver high-impedance output current VA,Y = 3.8V, VB,Z = 1.2V, DE = GND VA,Y = 0V or 2.4V, VB,Z = 1.2V, DE = GND -20 VA,Y = -1.4V, VB,Z = 1.2V, DE = GND -32 A VB,Z = 3.8V, VA,Y = 1.2V, DE = GND VB,Z = 0V or 2.4V, VA,Y = 1.2V, DE = GND -20 VB,Z = -1.4V, VA,Y = 1.2V, DE = GND -32 -4 IAB, IYZ Receiver input or driver high-impedance output differential current (IA - IB or IY - IZ) VA,Y = VB,Z, -1.4V V 3.8V, DE = GND IA(OFF), IY(OFF) Receiver input or driver high-impedance output power-off current VA,Y = 3.8V, VB,Z = 1.2V, DE = 0V 32 A +20 A A +4 A 32 A +20 A 0V VCC 1.5V VA,Y = 0V or 2.4V, VB,Z = 1.2V, DE = 0V -20 0V VCC 1.5V VA,Y = -1.4V, VB,Z = 1.2V, DE = 0V -32 A 0V VCC 1.5V IB(OFF), IZ(OFF) Receiver input or driver high-impedance output power-off current VB,Z = 3.8V, VA,Y = 1.2V, DE = 0V 32 A +20 A 0V VCC 1.5V VB,Z = 0V or 2.4V, VA,Y = 1.2V, DE = 0V -20 0V VCC 1.5V VB,Z = -1.4V, VA,Y = 1.2V, DE = 0V -32 A 0V VCC 1.5V IAB(OFF), IYZ(OFF) Receiver input or driver high-impedance output power-off differential current (IA(OFF) - IB(OFF) or IY(OFF) - IZ(OFF)) VA,Y = VB,Z, -1.4V V 3.8V, DE = 0V CA, CB Receiver input capacitance VCC = OPEN CY, CZ CAB -4 +4 A 0V VCC 1.5V 5.1 pF Driver output capacitance 8.5 pF Receiver input differential capacitance 2.5 pF CYZ Driver output differential capacitance 5.5 pF CA/B, CY/Z Receiver input or driver output capacitance balance (CA/CB or CY/CZ) 1.0 SUPPLY CURRENT (VCC) ICCD Driver Supply Current RL = 50, DE = VCC, RE = VCC ICCZ TRI-STATE Supply Current DE = GND, RE = VCC ICCR Receiver Supply Current DE = GND, RE = GND ICCB Supply Current, Driver and Receiver Enabled DE = VCC, RE = GND 20 www.national.com 4 17 29.5 mA 7 9.0 mA 14 18.5 mA 29.5 mA Over recommended operating supply and temperature ranges unless otherwise specified. (Note 3, Note 8) Symbol Parameter Conditions Min Typ Max Units DRIVER AC SPECIFICATION tPLH Differential Propagation Delay Low to High RL = 50, CL = 5 pF, 1.0 3.4 5.5 ns tPHL Differential Propagation Delay High to Low CD = 0.5 pF 1.0 3.1 5.5 ns tSKD1 (tsk(p)) Pulse Skew |tPLHD - tPHLD| (Note 5, Note 9) Figure 7 and Figure 8 300 420 ps tSKD3 Part-to-Part Skew (Note 6, Note 9) 1.9 ns tTLH (tr) Rise Time (Note 9) 1.0 1.8 3.0 ns tTHL (tf) Fall Time (Note 9) 1.0 1.8 3.0 ns tPZH Enable Time (Z to Active High) RL = 50, CL = 5 pF, 8 ns tPZL Enable Time (Z to Active Low ) CD = 0.5 pF 8 ns tPLZ Disable Time (Active Low to Z) Figure 9 and Figure 10 8 ns tPHZ Disable Time (Active High to Z) 8 ns tJIT Random Jitter, RJ (Note 9) 5.5 psrms fMAX Maximum Data Rate 100MHz clock pattern (Note 7) 2.5 200 Mbps RECEIVER AC SPECIFICATION tPLH Propagation Delay Low to High CL = 15 pF 2.0 4.7 7.5 ns tPHL Propagation Delay High to Low Figure 11 Figure 12and Figure 13 2.0 5.3 7.5 ns tSKD1 (tsk(p)) Pulse Skew |tPLHD - tPHLD| (Note 5, Note 9) 0.6 1.9 ns tSKD3 Part-to-Part Skew (Note 6, Note 9) tTLH (tr) Rise Time (Note 9) tTHL (tf) Fall Time (Note 9) tPZH Enable Time (Z to Active High) RL = 500, CL = 15 pF tPZL Enable Time (Z to Active Low) Figure 14 and Figure 15 tPLZ Disable Time (Active Low to Z) tPHZ Disable Time (Active High to Z) fMAX Maximum Data Rate 1.5 ns 0.5 1.2 3.0 ns 0.5 1.2 3.0 ns 10 ns 10 ns 10 ns 10 200 ns Mbps Note 1: "Absolute Maximum Ratings" are those beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should be operated at these limits. The tables of "Electrical Characteristics" provide conditions for actual device operation. Note 2: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise specified. Note 3: All typicals are given for VCC = 3.3V and TA = 25C. Note 4: The algebraic convention, in which the least positive (most negative) limit is designated as minimum, is used in this datasheet. Note 5: tSKD1, |tPLHD - tPHLD|, is the magnitude difference in differential propagation delay time between the positive going edge and the negative going edge of the same channel. Note 6: tSKD3, Part-to-Part Skew, is defined as the difference between the minimum and maximum specified differential propagation delays. This specification applies to devices at the same VCC and within 5C of each other within the operating temperature range. Note 7: Stimulus and fixture jitter has been subtracted. Note 8: CL includes fixture capacitance and CD includes probe capacitance. Note 9: Not production tested. Guaranteed by a statistical analysis on a sample basis at the time of characterization. 5 www.national.com DS91D180/DS91C180 Switching Characteristics DS91D180/DS91C180 Test Circuits and Waveforms 20041914 FIGURE 2. Differential Driver Test Circuit 20041944 FIGURE 3. Differential Driver Waveforms 20041922 FIGURE 4. Differential Driver Full Load Test Circuit www.national.com 6 DS91D180/DS91C180 20041912 FIGURE 5. Differential Driver DC Open Test Circuit 20041927 FIGURE 6. Differential Driver Short-Circuit Test Circuit 20041916 FIGURE 7. Driver Propagation Delay and Transition Time Test Circuit 7 www.national.com DS91D180/DS91C180 20041918 FIGURE 8. Driver Propagation Delays and Transition Time Waveforms 20041919 FIGURE 9. Driver TRI-STATE Delay Test Circuit 20041921 FIGURE 10. Driver TRI-STATE Delay Waveforms www.national.com 8 DS91D180/DS91C180 20041915 FIGURE 11. Receiver Propagation Delay and Transition Time Test Circuit 20041917 FIGURE 12. Type 1 Receiver Propagation Delay and Transition Time Waveforms 20041923 FIGURE 13. Type 2 Receiver Propagation Delay and Transition Time Waveforms 9 www.national.com DS91D180/DS91C180 20041913 FIGURE 14. Receiver TRI-STATE Delay Test Circuit 20041920 FIGURE 15. Receiver TRI-STATE Delay Waveforms www.national.com 10 DS91D180/DS91C180 Function Tables DS91D180/DS91C180 Transmitting Inputs Outputs DE D Z Y 2.0V 2.0V 0.8V 2.0V 0.8V X L H Z H L Z X -- Don't care condition Z -- High impedance state DS91C180 Receiving DS91D180 Receiving Inputs Output Inputs Output RE A-B R RE A-B R 0.8V 0.8V L 0.8V +0.15V +0.05V H 0.8V +0.05V -0.05V H 0.8V 2.0V 0V X X Z 0.8V 2.0V 0V X L Z X -- Don't care condition Z -- High impedance state L X -- Don't care condition Z -- High impedance state DS91D180 Receiver Input Threshold Test Voltages Applied Voltages Resulting Differential Input Voltage Resulting Common-Mode Input Voltage Receiver Output VIA VIB VID VIC R 2.400V 0.000V 3.800V 3.750V -1.400V -1.350V 0.000V 2.400V 3.750V 3.800V -1.350V -1.400V 2.400V -2.400V 0.050V -0.050V -0.050V 0.050V 1.200V 1.200V 3.775V 3.775V -1.375V -1.375V H L H L H L H -- High Level L -- Low Level Output state assumes that the receiver is enabled (RE = L) DS91C180 Receiver Input Threshold Test Voltages Applied Voltages Resulting Differential Input Voltage Resulting Common-Mode Input Voltage Receiver Output VIA VIB VID VIC R 2.400V 0.000V 3.800V 3.800V -1.250V -1.350V 0.000V 2.400V 3.650V 3.750V -1.400V -1.400V 2.400V -2.400V 0.150V 0.050V 0.150V 0.050V 1.200V 1.200V 3.725V 3.775V -1.325V -1.375V H L H L H L H -- High Level L -- Low Level Output state assumes that the receiver is enabled (RE = L) 11 www.national.com DS91D180/DS91C180 Pin Descriptions www.national.com Pin No. Name 1, 8 NC Description No connect. 2 R 3 RE Receiver output pin Receiver enable pin: When RE is high, the receiver is disabled. When RE is low or open, the receiver is enabled. 4 DE Driver enable pin: When DE is low, the driver is disabled. When DE is high, the driver is enabled. 5 D 6, 7 GND 9 Y Non-inverting driver output pin 10 Z Inverting driver output pin 11 B Inverting receiver input pin 12 A Non-inverting receiver input pin 13, 14 VCC Power supply pin, +3.3V 0.3V Driver input pin Ground pin 12 DS91D180/DS91C180 Physical Dimensions inches (millimeters) unless otherwise noted Order Number DS91D180TMA, DS91C180TMA See NS package Number M14A 13 www.national.com DS91D180/DS91C180 100 MHz M-LVDS Line Driver/Receiver Pair Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage Reference www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Solutions www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic Wireless (PLL/VCO) www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2009 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com