SR C4 382 SRC4382 SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Two-Channel, Asynchronous Sample Rate Converter with Integrated Digital Audio Interface Receiver and Transmitter FEATURES 1 * Two-Channel Asynchronous Sample Rate Converter (SRC) - Dynamic Range with -60dB Input (A-Weighted): 128dB typical - Total Harmonic Distortion and Noise (THD+N) with Full-Scale Input: -125dB typical - Supports Audio Input and Output Data Word Lengths Up to 24 Bits - Supports Input and Output Sampling Frequencies Up to 216kHz - Automatic Detection of the Input-to-Output Sampling Ratio - Wide Input-to-Output Conversion Range: 16:1 to 1:16 Continuous - Excellent Jitter Attenuation Characteristics - Digital De-Emphasis Filtering for 32kHz, 44.1kHz, and 48kHz Input Sampling Rates - Digital Output Attenuation and Mute Functions - Output Word Length Reduction - Status Registers and Interrupt Generation for Sampling Ratio and Ready Flags * Digital Audio Interface Transmitter (DIT) - Supports Sampling Rates Up to 216kHz - Includes Differential Line Driver and CMOS Buffered Outputs - Block-Sized Data Buffers for Both Channel Status and User Data - Status Registers and Interrupt Generation for Flag and Error Conditions * User-Selectable Serial Host Interface: SPI or Philips I2CTM - Provides Access to On-Chip Registers and Data Buffers * 234 U.S. Patent No. 7,262,716 * * * * * Digital Audio Interface Receiver (DIR) - PLL Lock Range Includes Sampling Rates from 20kHz to 216kHz - Includes Four Differential Input Line Receivers and an Input Multiplexer - Bypass Multiplexer Routes Line Receiver Outputs to Line Driver and Buffer Outputs - Block-Sized Data Buffers for Both Channel Status and User Data - Automatic Detection of Non-PCM Audio Streams (DTS CD/LD and IEC 61937 formats) - Audio CD Q-Channel Sub-Code Decoding and Data Buffer - Status Registers and Interrupt Generation for Flag and Error Conditions - Low Jitter Recovered Clock Output Two Audio Serial Ports (Ports A and B) - Synchronous Serial Interface to External Signal Processors, Data Converters, and Logic - Slave or Master Mode Operation with Sampling Rates up to 216kHz - Supports Left-Justified, Right-Justified, and Philips I2STM Data Formats - Supports Audio Data Word Lengths Up to 24 Bits Four General-Purpose Digital Outputs - Multifunction Programmable Via Control Registers Extensive Power-Down Support - Functional Blocks May Be Disabled Individually When Not In Use Operates From +1.8V Core and +3.3V I/O Power Supplies Small TQFP-48 Package, Compatible with the SRC4392 and DIX4192 1 2 3 4 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Dolby is a registered trademark of Dolby Laboratories. I2C, I2S are trademarks of Koninklijke Philips Electronics N.V. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2006-2007, Texas Instruments Incorporated SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 APPLICATIONS * * * * * * * DESCRIPTION DIGITAL AUDIO RECORDERS AND MIXING DESKS DIGITAL AUDIO INTERFACES FOR COMPUTERS DIGITAL AUDIO ROUTERS AND DISTRIBUTION SYSTEMS BROADCAST STUDIO EQUIPMENT DVD/CD RECORDERS SURROUND SOUND DECODERS AND A/V RECEIVERS CAR AUDIO SYSTEMS The SRC4382 is a highly-integrated CMOS device designed for use in professional and broadcast digital audio systems. The SRC4382 combines a high-performance, two-channel, asynchronous sample rate converter (SRC) with a digital audio interface receiver (DIR) and transmitter (DIT), two audio serial ports, and flexible distribution logic for interconnection of the function block data and clocks. The DIR and DIT are compatible with the AES3, S/PDIF, IEC 60958, and EIAJ CP-1201 interface standards. The audio serial ports, DIT, and SRC may be operated at sampling rates up to 216kHz. The DIR lock range includes sampling rates from 20kHz to 216kHz. The SRC4382 is configured using on-chip control registers and data buffers, which are accessed through either a 4-wire serial peripheral interface (SPI) port, or a 2-wire Philips I2C bus interface. Status registers provide access to a variety of flag and error bits, which are derived from the various function blocks. An open drain interrupt output pin is provided, and is supported by flexible interrupt reporting and mask options via control register settings. A master reset input pin is provided for initialization by a host processor or supervisory functions. The SRC4382 requires a +1.8V core logic supply, in addition to a +3.3V supply for powering portions of the DIR, DIT, and line driver and receiver functions. A separate logic I/O supply supports operation from +1.65V to +3.6V, providing compatibility with low voltage logic interfaces typically found on digital signal processors and programmable logic devices. The SRC4382 is available in a lead-free, TQFP-48 package, and is pin- and register-compatible with the Texas Instruments SRC4392 and DIX4192 products. 2 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) (1) PRODUCT PACKAGE PACKAGE DESIGNATOR SRC4382 TQFP-48 PFB OPERATING TEMPERATURE RANGE PACKAGE MARKING -40C to +85C SRC4382I ORDERING NUMBER TRANSPORT MEDIA, QUANTITY SRC4382IPFBT Tape and Reel, 250 SRC4382IPFBR Tape and Reel, 2000 For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) Power Supplies VDD18 -0.3V to +2.0V VDD33 -0.3V to +4.0V VIO -0.3V to +4.0V VCC -0.3V to +4.0V Digital Input Voltage: Digital Logic RXCKI, MUTE, CPM, CS, CCLK, CDIN, CDOUT, INT, RST, MCLK, BLS, SYNC, BCKA, BCKB, LRCKA, LRCKB, SDINA, SDINB -0.3V to (VIO + 0.3V) Line Receiver Input Voltage (per pin) RX1+, RX1-, RX2+, RX2-, RX3+, RX3-, RX4+, RX4- (VDD33 + 0.3) VPP Input Current (all pins except power and ground) 10mA Ambient Operating Temperature -40C to +85C Storage Temperature (1) -65C to +150C These limits are stress ratings only. Stresses beyond these limits may result in permanent damage. Extended exposure to absolute maximum ratings may degrade device reliability. Normal operation or performance at or beyond these limits is not specified or ensured. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 3 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 ELECTRICAL CHARACTERISTICS: General, SRC, DIR, and DIT All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. SRC4382 PARAMETER CONDITIONS MIN TYP MAX UNITS VIO V DIGITAL I/O CHARACTERISTICS (All I/O Pins Except Line Receivers and Line Driver) High-Level Input Voltage, VIH 0.7 VIO Low-Level Input Voltage, VIL 0 High-Level Input Current, IIH 0.5 0.3 VIO V 10 A 10 A High-Level Output Voltage, VOH IO = -4mA 0.8 VIO VIO V Low-Level Output Voltage, VOL IO = +4mA 0 0.2 VIO Low-Level Input Current, VIL 0.5 Input Capacitance, CIN 3 V pF LINE RECEIVER INPUTS (RX1+, RX1-, RX2+, RX2-, RX3+, RX3-, RX4+, RX4-) Differential Input Sensitivity, VTH Voltage across a given differential input pair Input Hysteresis, VHY 150 200 mV 150 mV 5.4 VPP LINE DRIVER OUTPUTS (TX+, TX-) Differential Output Voltage, VTXO RL = 110 Across TX+ and TX- MASTER CLOCK INPUT Master Clock Input (MCLK) Frequency, fMCLK 1 27.7 MHz Master Clock Input (MCLK) Duty Cycle, fMCLKD 45 55 % 4 216 kHz 1:16 16:1 ASYNCHRONOUS SAMPLE RATE CONVERTER (SRC) Input or Output Sampling Rate, fSIN or fSOUT Input-to-Output Sampling Ratio Interchannel Gain Mismatch 0 dB 0 Degrees fSIN:fSOUT = 12kHz:192kHz 125 dB fSIN:fSOUT = 44.1kHz:44.1kHz 125 dB fSIN:fSOUT = 44.1kHz:48kHz 125 dB fSIN:fSOUT = 44.1kHz:96kHz 125 dB fSIN:fSOUT = 44.1kHz:192kHz 125 dB fSIN:fSOUT = 48kHz:44.1kHz 125 dB fSIN:fSOUT = 48kHz:48kHz 125 dB fSIN:fSOUT = 48kHz:96kHz 125 dB fSIN:fSOUT = 48kHz:192kHz 125 dB fSIN:fSOUT = 96kHz:44.1kHz 125 dB fSIN:fSOUT = 96kHz:48kHz 125 dB fSIN:fSOUT = 96kHz:96kHz 125 dB fSIN:fSOUT = 96kHz:192kHz 125 dB fSIN:fSOUT = 192kHz:12kHz 125 dB fSIN:fSOUT = 192kHz:44.1kHz 125 dB fSIN:fSOUT = 192kHz:48kHz 125 dB fSIN:fSOUT = 192kHz:96kHz 125 dB fSIN:fSOUT = 192kHz:192kHz 125 dB Interchannel Phase Mismatch Dynamic Range (no weighting filter applied) (1) (1) 4 BW = 22Hz to fSOUT/2, f = 997Hz at -60dBFS Measured with an Audio Precision SYS-2722 192kHz test system with the input and output sampling frequencies asynchronous to one another. A-weighted dynamic range specifications will be improved by approximately 2dB to 3dB when compared to the results without A-weighting applied. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 ELECTRICAL CHARACTERISTICS: General, SRC, DIR, and DIT (continued) All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. SRC4382 PARAMETER Total Harmonic Distortion + Noise (THD+N) (2) CONDITIONS MIN TYP MAX UNITS BW = 22Hz to fSOUT/2, f = 997Hz at 0dBFS fSIN:fSOUT = 12kHz:192kHz -125 dB fSIN:fSOUT = 44.1kHz:44.1kHz -125 dB fSIN:fSOUT = 44.1kHz:48kHz -125 dB fSIN:fSOUT = 44.1kHz:96kHz -125 dB fSIN:fSOUT = 44.1kHz:192kHz -125 dB fSIN:fSOUT = 48kHz:44.1kHz -125 dB fSIN:fSOUT = 48kHz:48kHz -125 dB fSIN:fSOUT = 48kHz:96kHz -125 dB fSIN:fSOUT = 48kHz:192kHz -125 dB fSIN:fSOUT = 96kHz:44.1kHz -125 dB fSIN:fSOUT = 96kHz:48kHz -125 dB fSIN:fSOUT = 96kHz:96kHz -125 dB fSIN:fSOUT = 96kHz:192kHz -125 dB fSIN:fSOUT = 192kHz:12kHz -125 dB fSIN:fSOUT = 192kHz:44.1kHz -125 dB fSIN:fSOUT = 192kHz:48kHz -125 dB fSIN:fSOUT = 192kHz:96kHz -125 dB fSIN:fSOUT = 192kHz:192kHz -125 dB Digital Interpolation Filter Characteristics Passband Passband Ripple Transition Band 0.4535 fSIN Stop Band 0.5465 fSIN Stop Band Attenuation 0.4535 fSIN Hz 0.007 dB 0.5465 fSIN Hz Hz -125 Group Delay (64 samples pre-buffered) Decimation filter enabled Group Delay (64 samples pre-buffered) Group Delay (32 samples pre-buffered) dB 102.53125/fSIN Seconds Direct down-sampling enabled 102/fSIN Seconds Decimation filter enabled 70.53125/fSIN Seconds Group Delay (32 samples pre-buffered) Direct down-sampling enabled 70/fSIN Seconds Group Delay (16 samples pre-buffered) Decimation filter enabled 54.53125/fSIN Seconds Group Delay (16 samples pre-buffered) Direct down-sampling enabled 54/fSIN Seconds Group Delay (8 samples pre-buffered) Decimation filter enabled 46.53125/fSIN Seconds Group Delay (8 samples pre-buffered) Direct down-sampling enabled 46/fSIN Seconds 0.4535 fSOUT Hz 0.008 dB 0.5465 fSOUT Hz Digital Decimation Filter Characteristics Passband Passband Ripple Transition Band 0.4535 fSOUT Stop Band 0.5465 fSOUT Stop Band Attenuation Hz -125 dB Group Delay Decimation filter enabled 36.46875/fSOUT Seconds Group Delay Direct down-sampling enabled 0 Seconds De-emphasis filter enabled 0.001 dB Digital De-Emphasis Filter Characteristics Filter Error for All Settings (2) Measured with an Audio Precision SYS-2722 192kHz test system with the input and output sampling frequencies asynchronous to one another. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 5 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 ELECTRICAL CHARACTERISTICS: General, SRC, DIR, and DIT (continued) All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. SRC4382 PARAMETER CONDITIONS MIN TYP MAX UNITS DIGITAL AUDIO INTERFACE RECEIVER (DIR) PLL Lock Range 20 216 kHz Reference Clock Input (RXCKI) Frequency, fRXCKI 3.5 27.7 MHz Reference Clock Input (RXCKI) Duty Cycle, fRXCKID 45 55 % Recovered Clock Output (RXCKO) Frequency, fRXCKO 3.5 27.7 MHz Recovered Clock Output (RXCKO) Duty Cycle, fRXCKOD Recovered Clock Output (RXCKO) Intrinsic Jitter 45 55 % Measured cycle-to-cycle 250 ps RMS Measured cycle-to-cycle 200 ps RMS DIGITAL AUDIO INTERFACE TRANSMITTER (DIT) Intrinsic Output Jitter ELECTRICAL CHARACTERISTICS: Audio Serial Ports All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. SRC4382 PARAMETER CONDITIONS MIN TYP MAX UNITS 216 kHz 13.824 MHz AUDIO SERIAL PORTS (Port A and Port B) LRCK Clock Frequency, fLRCK 0 LRCK Clock Duty Cycle, tLRCKD 50 % BCK Clock Frequency, fBCK 0 BCK High Pulse Width, tBCKH 10 ns BCK Low Pulse Width, tBCKL 10 ns Audio Data Input (SDIN) Setup Time, tAIS 10 ns Audio Data Input (SDIN) Hold Time, tAISH 10 ns Audio Data Output (SDOUT) Delay, tADD 10 ns ELECTRICAL CHARACTERISTICS: SPI Interface All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. SRC4382 PARAMETER CONDITIONS MIN TYP MAX UNITS 40 MHz HOST INTERFACE: SPI Mode Serial Clock (CCLK) Frequency, fCCLK 0 CS Falling to CCLK Rising, tCSCR 8 ns CCLK Falling to CS Rising, tCFCS 7 ns CDIN Data Setup Time, tCDS 7 ns CDIN Data Hold Time, tCDH 6 ns CCLK Falling to CDOUT Data Valid, tCFDO 3 ns CS Rising to CDOUT High-Impedance, tCSZ 3 ns 6 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 ELECTRICAL CHARACTERISTICS: I2C Standard and Fast Modes All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. SRC4382 PARAMETER 2 HOST INTERFACE: I C Standard Mode CONDITIONS MIN TYP MAX UNITS 100 kHz (1) SCL Clock Frequency, fSCL 0 Hold Time Repeated START Condition, tHDSTA 4 s Low Period of SCL Clock, tLOW 4.7 s High Period of SCL Clock, tHIGH 4 s Setup Time Repeated START Condition, tSUSTA 4.7 Data Hold Time, tHDDAT 0 (2) Data Setup Time, tSUDAT 250 s 3.45 (3) s ns Rise Time for Both SDA and SDL, tR 1000 ns Fall Time for Both SDA and SDL, tF 300 ns Setup Time for STOP Condition, tSUSTO s 4 Bus Free Time Between START and STOP, tBUF s 4.7 Capacitive Load for Each Bus Line, CB 400 pF Noise Margin at Low Level (including hysteresis), VNL 0.1 VIO V Noise Margin at High Level (including hysteresis), VNH 0.2 VIO V 2 HOST INTERFACE: I C Fast Mode (1) SCL Clock Frequency, fSCL 0 400 kHz Hold Time Repeated START Condition, tHDSTA 0.6 s Low Period of SCL Clock, tLOW 1.3 s High Period of SCL Clock, tHIGH 0.6 s Setup Time Repeated START Condition, tSUSTA 0.6 Data Hold Time, tHDDAT 0 (2) Data Setup Time, tSUDAT 100 (4) s 0.9 (3) s ns Rise Time for Both SDA and SDL, tR 20 + 0.2CB (5) 300 ns Fall Time for Both SDA and SDL, tF 20 + 0.2CB (5) 300 ns Setup Time for STOP Condition, tSUSTO 0.6 Bus Free Time Between START and STOP, tBUF 1.3 Spike Pulse Width Suppressed by Input Filter, tSP 0 Capacitive Load for Each Bus Line, CB s s 50 ns 400 pF Noise Margin at Low Level (including hysteresis), VNL 0.1 VIO V Noise Margin at High Level (including hysteresis), VNH 0.2 VIO V (1) (2) (3) (4) (5) All values referred to the VIH minimum and VIL maximum levels listed in the Digital I/O Characteristics section of the Electrical Characteristics: General, SRC, DIR, and DIT table. A device must internally provide a hold time of at least 300ns for the SDA signal (referred to the VIH minimum input level) to bridge the undefined region of the falling edge of SCL. The maximum tHDDAT has only to be met if the device does not stretch the Low period (tLOW) of the SCL signal. A Fast mode I2C bus device can be used in a Standard mode I2C bus system, but the requirement that tSUDAT be 250ns minimum must then be met. For the SRC4382, this is automatically the case, since the device does not stretch the Low period of the SCL signal. CB is defined as the total capacitance of one bus line in picofarads (pF). If mixed with High-Speed mode devices, faster fall times are allowed. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 7 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 ELECTRICAL CHARACTERISTICS: Power Supplies All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. SRC4382 PARAMETER CONDITIONS MIN TYP MAX UNITS VDD18 +1.65 +1.8 +1.95 V VDD33 +3.0 +3.3 +3.6 V VIO +1.65 +3.3 +3.6 V VCC +3.0 +3.3 +3.6 V POWER SUPPLIES Recommended Supply Voltage Range Supply Current: Initial Startup All Blocks Powered Down by Default IDD18S VDD18 = +1.8V 90 A IDD33S VDD33 = +3.3V 1 A IIOS VIO = +3.3V 270 A ICCS VCC = +3.3V 1 A Supply Current: Quiescent All Blocks Powered Up with No Clocks Applied IDD18Q VDD18 = +1.8V 3.1 mA IDD33Q VDD33 = +3.3V 0.5 mA IIOQ VIO = +3.3V 0.27 mA ICCQ VCC = +3.3V 6.6 mA Supply Current: Dynamic All Blocks Powered Up, fS = 48kHz IDD18D VDD18 = +1.8V 23 mA IDD33D VDD33 = +3.3V 14 mA IIOD (1) VIO = +3.3V 43 mA ICCD VCC = +3.3V 8 mA Supply Current: High Sampling Rate All Blocks Powered Up, fS = 192kHz IDD18H VDD18 = +1.8V 58 mA IDD33H VDD33 = +3.3V 15 mA IIOH (1) VIO = +3.3V 44 mA ICCH VCC = +3.3V 8 mA All Blocks Powered Down by Default 1 mW Total Power Dissipation: Initial Startup Total Power Dissipation: Quiescent All Blocks Powered Up with No Clocks Applied 30 mW Total Power Dissipation: Dynamic All Blocks Powered Up, fS = 48kHz 256 mW Total Power Dissipation: High Sampling Rate All Blocks Powered Up, fS = 192kHz 326 mW (1) 8 The typical VIO supply current is measured using the SRC4382EVM evaluation module with loading from the DAIMB mother-board circuitry. VIO supply current will be dependent upon the loading on the logic output pins. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 TIMING DIAGRAMS LRCK tBCKH BCK tAIS tBCKL SDIN tAIH tAOD SDOUT Figure 1. Audio Serial Port Timing tCFCS CS tCSCR tCDS CCLK tCDH CDIN Hi Z Hi Z CDOUT tCFDO tCSZ Figure 2. SPI Interface Timing tF SDA tLOW tSUDAT tR tHDSTA tSP tR tBUF tF SCL tHDSTA S tSUSTA tHDDAT tHIGH S = Start Condition tSUSTO R P R = Repeated Start Condition P = Stop Condition S Figure 3. I2C Standard and Fast Mode Timing Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 9 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 BCKA SDINA TQFP LRCKA SDOUTA VIO NC BGND SDOUTB LRCKB SDINB BCKB Top View DGND3 PIN CONFIGURATION 48 47 46 45 44 43 42 41 40 39 38 37 RX1+ 1 36 SYNC RX1- 2 35 BLS RX2+ 3 34 AESOUT RX2- 4 33 VDD33 RX3+ 5 32 TX+ RX3- 6 31 TX- SRC4382 RX4+ 7 30 DGND2 RX4- 8 29 GPO4 VCC 9 28 GPO3 AGND 10 27 GPO2 LOCK 11 26 GPO1 RXCKO 12 25 MCLK RST INT CDOUT CDIN CS CCLK CPM VDD18 DGND1 RDY MUTE RXCKI 13 14 15 16 17 18 19 20 21 22 23 24 NC = No Connection PIN DESCRIPTIONS 10 NAME PIN NUMBER I/O RX1+ 1 Input DESCRIPTION Line Receiver 1, Noninverting Input RX1- 2 Input Line Receiver 1, Inverting Input RX2+ 3 Input Line Receiver 2, Noninverting Input RX2- 4 Input Line Receiver 2, Inverting Input RX3+ 5 Input Line Receiver 3, Noninverting Input RX3- 6 Input Line Receiver 3, Inverting Input RX4+ 7 Input Line Receiver 4, Noninverting Input RX4- 8 Input Line Receiver 4, Inverting Input VCC 9 Power DIR Comparator and PLL Power Supply, +3.3V Nominal AGND 10 Ground DIR Comparator and PLL Power-Supply Ground LOCK 11 Output DIR PLL Lock Flag (active Low) RXCKO 12 Output DIR Recovered Master Clock (tri-state output) RXCKI 13 Input DIR Reference Clock MUTE 14 Input SRC Output Mute (active High) RDY 15 Output SRC Ready Flag (active Low) DGND1 16 Ground Digital Core Ground VDD18 17 Power Digital Core Supply, +1.8V Nominal CPM 18 Input Control Port Mode, 0 = SPI Mode, 1 = I2C Mode CS or A0 19 Input Chip Select (active Low) for SPI Mode or Programmable Slave Address for I2C Mode CCLK or SCL 20 Input Serial Data Clock for SPI Mode or I2C Mode CDIN orA1 21 Input SPI Port Serial Data input or Programmable Slave Address for I2C Mode CDOUT or SDA 22 I/O SPI Port Serial Data Output (tri-state output) or Serial Data I/O for I2C Mode Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 PIN DESCRIPTIONS (continued) NAME PIN NUMBER I/O INT 23 Output DESCRIPTION RST 24 Input Reset (active Low) MCLK 25 Input Master Clock GPO1 26 Output General-Purpose Output 1 GPO2 27 Output General-Purpose Output 2 GPO3 28 Output General-Purpose Output 3 GPO4 29 Output General-Purpose Output 4 DGND2 30 Ground DIR Line Receiver Bias and DIT Line Driver Digital Ground TX- 31 Output DIT Line Driver Inverting Output TX+ 32 Output DIT Line Driver Noninverting Output VDD33 33 Power DIR Line Receiver Bias and DIT Line Driver Supply, +3.3V Nominal AESOUT 34 Output DIT Buffered AES3-Encoded Data BLS 35 I/O SYNC 36 Output BCKA 37 I/O Audio Serial Port A Bit Clock LRCKA 38 I/O Audio Serial Port A Left/Right Clock SDINA 39 Input SDOUTA 40 Output NC 41 -- VIO 42 Power Logic I/O Supply, +1.65V to +3.6V DGND3 43 Ground Logic I/O Ground BGND 44 Ground Substrate Ground, Connect to AGND (pin 10) SDOUTB 45 Output Audio Serial Port B Data Output SDINB 46 Input LRCKB 47 I/O Audio Serial Port B Left/Right Clock BCKB 48 I/O Audio Serial Port B Bit Clock Interrupt Flag (open-drain, active Low) DIT Block Start Clock DIT internal Sync Clock Audio Serial Port A Data Input Audio Serial Port A Data Output No Internal Signal Connection, Internally Bonded to ESD Pad Audio Serial Port B Data Input Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 11 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 TYPICAL CHARACTERISTICS All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. THD+N vs INPUT SAMPLING RATE (fSOUT = 48kHz and fIN = 997Hz at 0dBFS) -115 -115 -117 -117 -119 -119 -121 -121 THD+N (dB) -123 -125 -127 -127 -129 -131 -131 -133 -133 -135 32 52 72 92 112 132 152 172 32 192 52 92 112 132 152 172 Sampling Rate (kHz) Figure 4. Figure 5. THD+N vs INPUT SAMPLING RATE (fSOUT = 96kHz and fIN = 997Hz at 0dBFS) THD+N vs INPUT SAMPLING RATE (fSOUT = 192kHz and fIN = 997Hz at 0dBFS) -115 -115 -117 -117 -119 -119 -121 -121 -123 -125 -127 192 -123 -125 -127 -129 -129 -131 -131 -133 -133 -135 -135 32 52 72 92 112 132 152 172 32 192 52 72 92 112 132 152 172 Sampling Rate (kHz) Sampling Rate (kHz) Figure 6. Figure 7. THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 44.1kHz:44.1kHz and Input Amplitude = 0dBFS) THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 44.1kHz:48kHz and Input Amplitude = 0dBFS) 192 -115 -115 -115 -117 -117 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -135 -135 100 1k 10k 20k Right Channel THD+N (dB) Left Channel THD+N (dB) -115 20 -135 20 Input Frequency (Hz) 100 1k 10k 20k Input Frequency (Hz) Figure 8. 12 72 Sampling Rate (kHz) THD+N (dB) THD+N (dB) -125 -129 -135 Left Channel THD+N (dB) -123 Right Channel THD+N (dB) THD+N (dB) THD+N vs INPUT SAMPLING RATE (fSOUT = 44.1kHz and fIN = 997Hz at 0dBFS) Figure 9. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 TYPICAL CHARACTERISTICS (continued) All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. -115 -115 -117 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -135 -135 1k -135 20 10k 20k 100 1k 10k 20k Input Frequency (Hz) Figure 10. Figure 11. THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 48kHz:44.1kHz and Input Amplitude = 0dBFS) THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 48kHz:48kHz and Input Amplitude = 0dBFS) -115 -115 -115 -115 -117 -117 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -135 -135 20 100 1k -135 20 10k 20k Right Channel THD+N (dB) Input Frequency (Hz) Right Channel THD+N (dB) Left Channel THD+N (dB) 100 1k 10k 20k Input Frequency (Hz) Input Frequency (Hz) Figure 12. Figure 13. THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 48kHz:96kHz and Input Amplitude = 0dBFS) THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 48kHz:192kHz and Input Amplitude = 0dBFS) -115 -115 -115 -115 -117 -117 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -135 -135 20 100 1k 10k 20k Right Channel THD+N (dB) Left Channel THD+N (dB) 100 Right Channel THD+N (dB) -115 -117 Right Channel THD+N (dB) Left Channel THD+N (dB) -115 20 Left Channel THD+N (dB) THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 44.1kHz:192kHz and Input Amplitude = 0dBFS) Right Channel THD+N (dB) Left Channel THD+N (dB) Left Channel THD+N (dB) THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 44.1kHz:96kHz and Input Amplitude = 0dBFS) -135 20 100 1k Input Frequency (Hz) Input Frequency (Hz) Figure 14. Figure 15. 10k 20k Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 13 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 TYPICAL CHARACTERISTICS (continued) All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. -115 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -135 -135 -135 20 10k 20k 100 1k 10k 20k Figure 17. THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 96kHz:96kHz and Input Amplitude = 0dBFS) THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 96kHz:192kHz and Input Amplitude = 0dBFS) -115 -115 -115 -115 -117 -117 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -135 -135 1k 10k -135 20 40k 100 1k 10k 40k Input Frequency (Hz) Input Frequency (Hz) Figure 18. Figure 19. THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 192kHz:44.1kHz and Input Amplitude = 0dBFS) THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 192kHz:48kHz and Input Amplitude = 0dBFS) -115 -115 -115 -115 -117 -117 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -135 -135 20 100 1k 10k 20k Right Channel THD+N (dB) 100 Right Channel THD+N (dB) Input Frequency (Hz) Figure 16. Right Channel THD+N (dB) Left Channel THD+N (dB) Left Channel THD+N (dB) 1k Input Frequency (Hz) 20 Left Channel THD+N (dB) 100 Right Channel THD+N (dB) -115 -117 Right Channel THD+N (dB) Left Channel THD+N (dB) -115 -117 20 14 THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 96kHz:48kHz and Input Amplitude = 0dBFS) -115 Right Channel THD+N (dB) Left Channel THD+N (dB) Left Channel THD+N (dB) THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 96kHz:44.1kHz and Input Amplitude = 0dBFS) -135 20 100 1k Input Frequency (Hz) Input Frequency (Hz) Figure 20. Figure 21. Submit Documentation Feedback 10k 20k Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 TYPICAL CHARACTERISTICS (continued) All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. -115 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -135 -135 1k 10k -135 20 40k 100 1k Input Frequency (Hz) Input Frequency (Hz) Figure 22. Figure 23. THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 44.1kHz:44.1kHz and Input Frequency = 997Hz) THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 44.1kHz:48kHz and Input Frequency = 997Hz) 80k -115 -115 -115 -115 -117 -117 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -125 -135 -135 -125 -100 -75 -50 -25 0 -135 -100 Input Amplitude (dBFS) -75 -50 -25 0 Input Amplitude (dBFS) Figure 25. THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 44.1kHz:96kHz and Input Frequency = 997Hz) THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 44.1kHz:192kHz and Input Frequency = 997Hz) -115 -115 -115 -115 -117 -117 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -125 -135 -135 -125 -100 -75 -50 -25 0 Input Amplitude (dBFS) Right Channel THD+N (dB) Figure 24. Right Channel THD+N (dB) Left Channel THD+N (dB) Left Channel THD+N (dB) 10k Right Channel THD+N (dB) 100 Right Channel THD+N (dB) -115 -117 Right Channel THD+N (dB) Left Channel THD+N (dB) -115 -117 20 Left Channel THD+N (dB) THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 192kHz:192kHz and Input Amplitude = 0dBFS) -115 Right Channel THD+N (dB) Left Channel THD+N (dB) Left Channel THD+N (dB) THD+N vs INPUT FREQUENCY (fSIN:fSOUT = 192kHz:96kHz and Input Amplitude = 0dBFS) -135 -100 -75 -50 -25 0 Input Amplitude (dBFS) Figure 26. Figure 27. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 15 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 TYPICAL CHARACTERISTICS (continued) All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. -115 -115 -115 -117 -117 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -125 -135 -135 -125 -100 -75 -50 -25 0 -135 -100 -50 -25 0 Input Amplitude (dBFS) THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 48kHz:96kHz and Input Frequency = 997Hz) THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 48kHz:192kHz and Input Frequency = 997Hz) -115 -115 -115 -115 -117 -117 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -125 -135 -135 -125 -75 -50 -25 0 -135 -100 -75 -50 -25 0 Input Amplitude (dBFS) Figure 30. Figure 31. THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 96kHz:44.1kHz and Input Frequency = 997Hz) THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 96kHz:48kHz and Input Frequency = 997Hz) -115 -115 -115 -117 -117 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -125 -135 -135 -125 -100 -75 -50 -25 0 Right Channel THD+N (dB) Left Channel THD+N (dB) -115 Input Amplitude (dBFS) Right Channel THD+N (dB) -100 Right Channel THD+N (dB) Figure 29. Input Amplitude (dBFS) Left Channel THD+N (dB) -75 Figure 28. Right Channel THD+N (dB) Left Channel THD+N (dB) Left Channel THD+N (dB) Input Amplitude (dBFS) -135 -100 -75 -50 -25 0 Input Amplitude (dBFS) Figure 32. 16 Right Channel THD+N (dB) THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 48kHz:48kHz and Input Frequency = 997Hz) -115 Right Channel THD+N (dB) Left Channel THD+N (dB) Left Channel THD+N (dB) THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 48kHz:44.1kHz and Input Frequency = 997Hz) Figure 33. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 TYPICAL CHARACTERISTICS (continued) All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. -115 -115 -115 -115 -117 -117 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -125 -135 -135 -125 -100 -75 -50 -25 0 -135 -100 -75 -50 -25 0 Input Amplitude (dBFS) Figure 35. THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 192kHz:44.1kHz and Input Frequency = 997Hz) THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 192kHz:48kHz and Input Frequency = 997Hz) -115 -115 -115 -115 -117 -117 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -125 -135 -135 -125 -100 -75 -50 -25 0 Right Channel THD+N (dB) Figure 34. Right Channel THD+N (dB) Left Channel THD+N (dB) -135 -100 Input Amplitude (dBFS) -75 -50 -25 0 Input Amplitude (dBFS) Figure 36. Figure 37. THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 192kHz:96kHz and Input Frequency = 997Hz) THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 192kHz:192kHz and Input Frequency = 997Hz) -115 -115 -115 -117 -117 -117 -117 -119 -119 -119 -119 -121 -121 -121 -121 -123 -123 -123 -123 -125 -125 -125 -125 -127 -127 -127 -127 -129 -129 -129 -129 -131 -131 -131 -131 -133 -133 -133 -133 -135 -125 -135 -135 -125 -100 -75 -50 -25 0 Right Channel THD+N (dB) Left Channel THD+N (dB) -115 Input Amplitude (dBFS) Right Channel THD+N (dB) Left Channel THD+N (dB) Input Amplitude (dBFS) Left Channel THD+N (dB) Right Channel THD+N (dB) THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 96kHz:192kHz and Input Frequency = 997Hz) Right Channel THD+N (dB) Left Channel THD+N (dB) Left Channel THD+N (dB) THD+N vs INPUT AMPLITUDE (fSIN:fSOUT = 96kHz:96kHz and Input Frequency = 997Hz) -135 -100 -75 -50 -25 0 Input Amplitude (dBFS) Figure 38. Figure 39. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 17 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 TYPICAL CHARACTERISTICS (continued) All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. FFT PLOT (fSIN:fSOUT = 44.1kHz:48kHz and Input Frequency = 997Hz at 0dBFS) 0 0 -20 -20 -40 -40 -60 -60 Amplitude (dB) Amplitude (dB) FFT PLOT (fSIN:fSOUT = 44.1kHz:44.1kHz and Input Frequency = 997Hz at 0dBFS) -80 -100 -120 -140 -160 -160 -180 -180 -200 100 1k 10k 22k 10 100 1k 10k Frequency (Hz) Frequency (Hz) Figure 40. Figure 41. FFT PLOT (fSIN:fSOUT = 44.1kHz:96kHz and Input Frequency = 997Hz at 0dBFS) FFT PLOT (fSIN:fSOUT = 44.1kHz:192kHz and Input Frequency = 997Hz at 0dBFS) -0 -0 -20 -20 -40 -40 -60 -60 Amplitude (dB) Amplitude (dB) 10 -80 -100 -120 24k -80 -100 -120 -140 -140 -160 -160 -180 -180 -200 -200 10 100 1k 20 48k 10k 100 1k Frequency (Hz) Figure 42. Figure 43. FFT PLOT (fSIN:fSOUT = 48kHz:44.1kHz and Input Frequency = 997Hz at 0dBFS) FFT PLOT (fSIN:fSOUT = 48kHz:48kHz and Input Frequency = 997Hz at 0dBFS) 0 0 -20 -20 -40 -40 -60 -60 -80 -100 -120 -80 -100 -120 -140 -140 -160 -160 -180 -180 -200 96k 10k Frequency (Hz) Amplitude (dB) Amplitude (dB) -120 -140 -200 -200 10 18 -80 -100 100 1k 10k 22k 10 100 1k Frequency (Hz) Frequency (Hz) Figure 44. Figure 45. Submit Documentation Feedback 10k 24k Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 TYPICAL CHARACTERISTICS (continued) All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. FFT PLOT (fSIN:fSOUT = 48kHz:192kHz and Input Frequency = 997Hz at 0dBFS) -0 -0 -20 -20 -40 -40 -60 -60 Amplitude (dB) Amplitude (dB) FFT PLOT (fSIN:fSOUT = 48kHz:96kHz and Input Frequency = 997Hz at 0dBFS) -80 -100 -120 -140 -160 -160 -180 -180 -200 10 100 1k 20 48k 10k 100 1k Frequency (Hz) Figure 46. Figure 47. FFT PLOT (fSIN:fSOUT = 96kHz:44.1kHz and Input Frequency = 997Hz at 0dBFS) FFT PLOT (fSIN:fSOUT = 96kHz:48kHz and Input Frequency = 997Hz at 0dBFS) -0 -0 -20 -20 -40 -40 -60 -60 -80 -100 -120 96k 10k Frequency (Hz) Amplitude (dB) Amplitude (dB) -120 -140 -200 -80 -100 -120 -140 -140 -160 -160 -180 -180 -200 -200 10 100 1k 10k 22k 10 100 1k 10k Frequency (Hz) Frequency (Hz) Figure 48. Figure 49. FFT PLOT (fSIN:fSOUT = 96kHz:96kHz and Input Frequency = 997Hz at 0dBFS) FFT PLOT (fSIN:fSOUT = 96kHz:192kHz and Input Frequency = 997Hz at 0dBFS) -0 -0 -20 -20 -40 -40 -60 -60 Amplitude (dB) Amplitude (dB) -80 -100 -80 -100 -120 -80 -100 -120 -140 -140 -160 -160 -180 -180 -200 24k -200 10 100 1k 10k 48k 20 100 1k Frequency (Hz) Frequency (Hz) Figure 50. Figure 51. 10k Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 96k 19 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 TYPICAL CHARACTERISTICS (continued) All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. FFT PLOT (fSIN:fSOUT = 192kHz:48kHz and Input Frequency = 997Hz at 0dBFS) 0 0 -20 -20 -40 -40 -60 -60 Amplitude (dB) Amplitude (dB) FFT PLOT (fSIN:fSOUT = 192kHz:44.1kHz and Input Frequency = 997Hz at 0dBFS) -80 -100 -120 -140 -160 -160 -180 -180 -200 100 1k 10k 10 22k 100 1k 10k Frequency (Hz) Frequency (Hz) Figure 52. Figure 53. FFT PLOT (fSIN:fSOUT = 192kHz:96kHz and Input Frequency = 997Hz at 0dBFS) FFT PLOT (fSIN:fSOUT = 192kHz:192kHz and Input Frequency = 997Hz at 0dBFS) -0 -0 -20 -20 -40 -40 -60 -60 Amplitude (dB) Amplitude (dB) 10 -80 -100 -120 24k -80 -100 -120 -140 -140 -160 -160 -180 -180 -200 -200 10 100 1k 20 48k 10k 100 1k 96k 10k Frequency (Hz) Frequency (Hz) Figure 54. Figure 55. IMD (fSIN:fSOUT = 44.1kHz:48kHz, SMPTE/DIN 1:1, 10kHz and 11kHz, and -0.1dB Input Amplitude) IMD (fSIN:fSOUT = 48kHz:44.1kHz, SMPTE/DIN 1:1, 10kHz and 11kHz, and -0.1dB Input Amplitude) 0 0 -20 -20 -40 -40 -60 -60 Amplitude (dB) Amplitude (dB) -120 -140 -200 -80 -100 -120 -80 -100 -120 -140 -140 -160 -160 -180 -180 -200 -200 0 20 -80 -100 2 4 6 8 10 12 14 16 18 20 22 24 0 2 4 6 8 10 12 14 Frequency (kHz) Frequency (kHz) Figure 56. Figure 57. Submit Documentation Feedback 16 18 20 22 Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 TYPICAL CHARACTERISTICS (continued) All specifications are at TA = +25C, VDD18 = +1.8V, VDD33 = +3.3V, VIO = +3.3V, and VCC = +3.3V, unless otherwise noted. IMD (fSIN:fSOUT = 96kHz:48kHz, SMPTE/DIN 1:1, 10kHz and 11kHz, and -0.1dB Input Amplitude) 0 -20 Amplitude (dB) -40 -60 -80 -100 -120 -140 -160 -180 -200 0 2 4 6 8 10 12 14 16 18 20 22 24 Frequency (kHz) Figure 58. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 21 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 PRODUCT OVERVIEW The SRC4382 is a two-channel asynchronous sample rate converter (SRC) with an integrated digital audio interface receiver and transmitter (DIR and DIT). Two audio serial ports, Port A and Port B, support input and output interfacing to external data converters, signal processors, and logic devices. On-chip routing logic provides for flexible interconnection between the five functional blocks. The audio serial ports, DIT, and SRC may be operated at sampling rates up to 216kHz. The DIR is specified for a PLL lock range that includes sampling rates from 20kHz to 216kHz. All function blocks support audio data word lengths up to 24 bits. The SRC4382 requires an external host processor or logic for configuration control. The SRC4382 includes a user-selectable serial host interface, which operates as either a 4-wire serial peripheral interface (SPI) port or a 2-wire Philips I2C bus interface. The SPI port operates at bit rates up to 40MHz. The I2C bus interface may be operated in standard or fast modes, supporting operation at 100kbps and 400kbps, respectively. The SPI and I2C interfaces provide access to internal control and status registers, as well as the buffers utilized for the DIR and DIT channel status and user data. The asynchronous SRC is based upon the successful SRC4192 core from Texas Instruments. The SRC in the SRC4382 has been further enhanced to provide exceptional jitter attenuation characteristics, helping to improve overall application performance. The SRC operates over a wide input-to-output sampling ratio range, from 1:16 to 16:1 continuous. The input-to-output sampling ratio is determined automatically by the SRC rate estimation circuitry, with the digital re-sampler parameters being updated in real-time without the need for programming. Interpolation and decimation filter delay are user-selectable. Additional SRC features include de-emphasis filtering, output word length reduction, output attenuation and muting, and input-to-output sampling ratio readback via status registers. The digital interface receiver (DIR) includes four differential input line receiver circuits, suitable for balanced or unbalanced cable interfaces. Interfacing to optical receiver modules and CMOS logic devices is also supported. The outputs of the line receivers are connected to a 1-of-4 data selector, referred to as the receiver input multiplexer, which is utilized to select one of the four line receiver outputs for processing by the DIR core. The outputs of the line receivers are also connected to a second data selector, the bypass multiplexer, which may be used to route input data streams to the DIT CMOS output buffer and differential line driver functions. This configuration provides a bypass signal path for AES3-encoded input data streams. The DIR core decodes the selected input stream data and separates the audio, channel status, user, validity, and parity data. Channel status and user data is stored in block-sized buffers, which may be accessed via the SPI or I2C serial host interface, or routed directly to the general-purpose output pins (GPO1 through GPO4). The validity and parity bits are processed to determine error status. The DIR core recovers a low jitter master clock, which may be utilized to generate word and bit clocks using on-chip or external logic circuitry. The digital interface transmitter (DIT) encodes digital audio input data into an AES3 formatted output data stream. Two DIT outputs are provided, including a differential line driver and a CMOS output buffer. Both the line driver and buffer include 1-of-2 input data selectors, which are utilized to choose either the output of the DIT AES3 encoder, or the output of the bypass multiplexer. The line driver output is suitable for balanced or unbalanced cable interfaces, while the CMOS output buffer supports interfacing to optical transmitter modules and external logic or line drivers. The DIT includes block-sized data buffers for both channel status and user data. These buffers are accessed via either the SPI or I2C host interface, or may be loaded directly from the DIR channel status and user data buffers. The SRC4382 includes four general-purpose digital outputs, or GPO pins. The GPO pins may be configured as simple logic outputs, which may be programmed to either a low or high state. Alternatively, the GPO pins may be connected to one of 14 internal logic nodes, allowing them to serve as functional, status, or interrupt outputs. The GPO pins provide added utility in applications where hardware access to selected internal logic signals may be necessary. 22 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Figure 59 shows a simplified functional block diagram for the SRC4382. Additional details for each function block will be covered in respective sections of this datasheet. SRC4382 SDINA SDOUTA LRCKA Host Interface 2 (SPI or I C) and GeneralPurpose Outputs Audio Serial Port A BCKA SDINB SDOUTB LRCKB CPM CS or A0 CCLK or SCL CDIN or A1 CDOUT or SDA INT RST GPO1 GPO2 GPO3 GPO4 Audio Serial Port B Control and Status Registers BCKB RXCKO DIR C and U Data Buffers LOCK RX1+ DIT C and U Data Buffers Digital Interface Receiver (DIR) RX1RX2+ AESOUT Master Clock Distribution BLS SYNC RDY MUTE Power Asynchronous Sample Rate Converter (SRC) MCLK RXCKI From RXCKO PORT A PORT B DIR DIT SRC PORT_B_IN Digital Interface Transmitter (DIT) PORT_A_IN RX4TX+ TX- SRC_OUT RX3RX4+ DIR_OUT RX2RX3+ Internally Tied to Substrate VDD18 DGND1 VDD33 DGND2 VIO DGND3 VCC AGND BGND Figure 59. Functional Block Diagram RESET OPERATION The SRC4382 includes an asynchronous active low reset input, RST (pin 24), which may be used to initialize the internal logic at any time. The reset sequence forces all registers and buffers to their default settings. The reset low pulse width must be a minimum of 500ns in length. The user should not attempt a write or read operation using either the SPI or I2C port for at least 500s after the rising edge of RST. See Figure 60 for the reset timing sequence of the SRC4382. In addition to reset input, the RESET bit in control register 0x01 may be used to force an internal reset, whereby all registers and buffers are forced to their default settings. Refer to the Control Registers section for details regarding the RESET bit function. Upon reset initialization, all functional blocks of the SRC4382 default to the powered-down state, with the exception of the SPI or I2C host interface and the corresponding control registers. The user may then program the SRC4382 to the desired configuration, and then release the desired function blocks from the power-down state utilizing the corresponding bits in control register 0x01. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 23 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Write or Read via 2 SPI or I C 1 RST 0 500ns (min) 500ms (min) Figure 60. Reset Sequence Timing MASTER AND REFERENCE CLOCKS The SRC4382 includes two clock inputs, MCLK (pin 25) and RXCKI (pin 13). The MCLK clock input is typically used as the master clock source for the audio serial ports, the DIT, and/or the SRC. The MCLK may also be utilized as the reference clock for the DIR. The RXCKI clock input is typically used for the DIR reference clock source, although it may also be used as the master or reference clock source for the audio serial ports and/or the SRC. In addition to the MCLK and RXCKI clock sources, the DIR core recovers a master clock from the AES3-encoded input data stream. This clock is suitable for use as a master or system clock source in many applications. The recovered master clock output, RXCKO (pin 12), may be utilized as the master or reference clock source for the audio serial ports, the DIT, and/or the SRC, as well as external audio devices. The master clock frequency for the audio serial ports (Port A and Port B) depends on the Slave or Master mode configuration of the port. In Slave mode, the ports do not require a master clock, as the left/right word and bit clocks are inputs, sourced from an external audio device serving as the serial bus timing master. In Master mode, the serial ports derive the left/right word and bit clock outputs from the selected master clock source, MCLK, RXCKI, or RXCKO. The left/right word clock rate is derived from the selected master clock source using one of four clock divider settings (divide by 128, 256, 384, or 512). Refer to the Audio Serial Port Operation section for additional details. The DIT always requires a master clock source, which may be either the MCLK input, or the DIR recovered clock output, RXCKO. Like the audio serial ports, the DIT output frame rate is derived from the selected master clock using one of four clock divider settings (divide by 128, 256, 384, or 512). Refer to the Digital Interface Transmitter (DIT) Operation section for additional details. The DIR reference clock may be any frequency that meets the PLL1 setup requirements, described in the Control Registers section. Typically, a common audio system clock rate, such as 11.2896MHz, 12.288MHz, 22.5792MHz, or 24.576MHz, may be used for this clock. The SRC reference clock rate may be any frequency up to 27.7MHz, and does not have to be related to or synchronous with the input or output sampling rates. The MCLK, RXCKI, or RXCKO clocks may be utilized as the reference clock source for the SRC. Refer to the Asynchronous Sample Rate Converter (SRC) Operation section for additional details. It is recommended that the clock sources for MCLK and RXCKI input be generated by low-jitter crystal oscillators for optimal performance. In general, phase-locked loop (PLL) clock synthesizers should be avoided, unless they are designed and/or specified for low clock jitter. 24 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 AUDIO SERIAL PORT OPERATION The SRC4382 includes two audio serial ports, Port A and Port B. Both ports are 4-wire synchronous serial interfaces, supporting simultaneous input and output operation. Since each port has only one pair of left/right word and bit clocks, the input and output sampling rates are identical. A simplified block diagram is shown in Figure 61. The audio serial ports may be operated at sampling rates up to 216kHz, and support audio data word lengths up to 24 bits. Philips I2S, Left-Justified, and Right-Justified serial data formats are supported. Refer to Figure 62. The left/right word clock (LRCKA or LRCKB) and the bit clock (BCKA or BCKB) may be configured for either Master or Slave mode operation. In Master mode these clocks are outputs, derived from the selected master clock source using internal clock dividers. The master clock source may be 128, 256, 384, or 512 times the audio input/output sampling rate, with the clock divider being selected using control register bits for each port. In Slave mode the left/right word and bit clocks are inputs, being sourced from an external audio device acting as the serial bus master. The LRCKA or LRCKB clocks operate at the input/output sampling rate, fS. The BCKA and BCKB clock rates are fixed at 64 times the left/right word clock rate in Master mode. For Slave mode, the minimum BCKA and BCKB clock rate is determined by the audio data word length multiplied by two, since there are two audio data channels per left/right word clock period. For example, if the audio data word length is 24 bits, the bit clock rate must be at least 48 times the left/right word clock rate, allowing one bit clock period for each data bit in the serial bit stream. Serial audio data is clocked into the port on the rising edge of the bit clock, while data is clocked out of the port on the falling edge of the bit clock. Refer to the Electrical Characteristics: Audio Serial Ports table for parametric information and Figure 1 for a timing diagram related to audio serial port operation. The audio serial ports are configured using control registers 0x03 through 0x06. Refer to the Control Registers section for descriptions of the control register bits. CLK[1:0] Master Clock Source MCLK M/S DIV[1:0] Master Mode Clock Generation RXCKI RXCKO SDINA (pin 39) or SDINB (pin 46) Audio Data Serial Input Internal Clocks Data Source LRCKA (pin 38) or LRCKB (pin 47) BCKA (pin 37) or BCKB (pin 48) Port A Port B DIR SRC Serial Output SDOUTA (pin 40) or SDOUTB (pin 45) OUTS[1:0] MUTE FMT[1:0] Figure 61. Audio Serial Port Block Diagram Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 25 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Channel 1 (Left Channel) Channel 2 (Right Channel) LRCKA LRCKB BCKA BCKB Audio Data MSB LSB MSB LSB (a) Left-Justified Data Format LRCKA LRCKB BCKA BCKB Audio MSB Data LSB MSB LSB (b) Right-Justified Data Format LRCKA LRCKB BCKA BCKB Audio Data MSB LSB MSB LSB 2 (c) I S Data Format 1/fs Figure 62. Audio Data Formats OVERVIEW OF THE AES3 DIGITAL AUDIO INTERFACE PROTOCOL This section introduces the basics of digital audio interface protocols pertaining to the transmitter (DIT) and receiver (DIR) blocks of the SRC4382. Emphasis is placed upon defining the basic terminology and characteristics associated with the AES3-2003 standard protocol, the principles of which may also be applied to a number of consumer-interface variations, including S/PDIF, IEC-60958, and EIAJ CP-1201. It is assumed that the reader is familiar with the AES3 and S/PDIF interface formats. Additional information is available from the sources listed in the Reference Documents section. The AES3-2003 standard defines a technique for two-channel linear PCM data transmission over 110 shielded twisted-pair cable. The AES-3id document extends the AES3 interface to applications employing 75 coaxial cable connections. In addition, consumer transmission variants, such as those defined by the S/PDIF, IEC 60958, and CP-1201 standards, utilize the same encoding techniques but with different physical interfaces or transmission media. Channel status data definitions also vary between professional and consumer interface implementations. 26 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 For AES3 transmission, data is encoded into frames, with each frame containing two subframes of audio and status data, corresponding to audio Channels 1 and 2 (or Left and Right, respectively, for stereophonic audio). Figure 63 shows the AES3 frame and subframe formatting. Each subframe includes four bits for the preamble, up to 24 bits for audio and/or auxiliary data, one bit indicating data validity (V), one bit for channel status data (C), one bit for user data (U), and one bit for setting parity (P). The 4-bit preamble is used for synchronization and identification of blocks and subframes. The X and Y preamble codes are used to identify the start of the Channel 1 and Channel 2 subframes, as shown in Figure 63. However, the X preamble for the first subframe of every 192 frames is replaced by the Z preamble, which identifies the start of a new block of channel status and user data. Block Start Frame 191 X Channel 1 Y Frame 0 Channel 2 Z Channel 1 Y Frame 1 Channel 2 X Channel 1 Y Channel 2 One Sub Frame Bits: 0 3 4 Preamble 7 8 Audio or Aux Data 27 28 29 30 31 Audio Data MSB V U C P Validity Bit User Data Channel Status Data Parity Bit Figure 63. AES3 Frame and Subframe Encoding One block is comprised of 192 frames of data. This format translates to 192 bits each for channel status and user data for each channel. The 192 bits are organized into 24 data bytes, which are defined by the AES3-2003 and consumer standards documents. The AES18 standard defines recommended usage and formatting of the user data bits, while consumer applications may utilize the user data for other purposes. The SRC4382 also includes block-sized transmitter and receiver channel status and user data buffers, which have 24 bytes each for the channel status and user data assigned to audio Channels 1 and 2. Refer to the Channel Status and User Data Buffer Maps section for the organization of the buffered channel status and user data for the receiver and transmitter functions. The audio data for Channel 1 and Channel 2 may be up to 24 bits in length, and occupies bits 4 through 27 of the corresponding subframe. Bit 4 is the LSB while bit 27 is the MSB. If only 20 bits are required for audio data, then bits 8 through 27 are utilized for audio data, while bits 4 though 7 are utilized for auxiliary data bits. The validity (V) bit indicates whether or not the audio sample word being transmitted is suitable for digital-to-analog (D/A) conversion or further digital processing at the receiver end of the connection. If the validity bit is 0, then the audio sample is suitable for conversion or additional processing. If the validity bit is 1, then the audio sample is not suitable for conversion or additional processing. The parity (P) bit is set to either a 0 or 1, such that bits 4 through 31 carry an even number of ones and zeros for even parity. The DIT block in the SRC4382 automatically manages the parity bit, setting it to a 0 or 1 as needed. The DIR block checks the parity of bits 4 though 31 and generates a parity error if odd parity is detected. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 27 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 The binary non-return to zero (NRZ) formatted audio and status source data for bits 4 through 31 of each subframe are encoded utilizing a Biphase Mark format for transmission. This format allows for clock recovery at the receiver end, as well as making the interface insensitive to the polarity of the balanced cable connections. The preambles at the start of each subframe are encoded to intentionally violate the Biphase Mark formatting, making their detection by the receiver reliable, as well as avoiding the possibility of audio and status data imitating the preambles. Figure 64 shows the Biphase Mark and preamble encoding. Although the AES3 standard originally defined transmission for sampling rates up to 48kHz, the interface is capable of handling higher sampling rates, given that attention is paid to cable length and impedance matching. Equalization at the receiver may also be required, depending on the cable and matching factors. It is also possible to transmit and decode more than two channels of audio data utilizing the AES3 or related consumer interfaces. Special encoding and/or compression algorithms are utilized to support multiple channels, including the Dolby(R) AC-3, DTS, MPEG-1/2, and other data reduced audio formats. Clock (2x Source Bit Rate) Source Data 1 Coding (NRZ) 0 Insert Preamble Code Below AES3 Channel 1 Coding (Biphase Mark) 0 Preamble Z (Block Start) Preceding State, from the Parity bit of the previous Frame. Preamble Coding Preceding State: Preamble: X Y Z 0 1 Channel Coding: 11100010 11100100 11101000 Channel Coding: 00011101 00011011 00010111 Description: Channel 1 Subframe Channel 2 Subframe Channel 1 Subframe and Block Start Figure 64. Biphase Mark Encoding DIGITAL INTERFACE TRANSMITTER (DIT) OPERATION The DIT encodes a given two-channel or data-reduced audio input stream into an AES3-encoded output stream. In addition to the encoding function, the DIT includes differential line driver and CMOS buffered output functions. The line driver is suitable for driving balanced or unbalanced line interfaces, while the CMOS buffered output is designed to drive external logic or line drivers, as well as optical transmitter modules. Figure 65 illustrates the functional block diagram for the DIT. The input of the DIT receives the audio data for Channels 1 and 2 from one of four possible sources: Port A, Port B, the DIR, or the SRC. By default, Port A is selected as the source. The DIT also requires a master clock source, which may be provided by either the MCLK input (pin 25) or RXCKO (the DIR recovered master clock output). A master clock divider is utilized to select the frame rate for the AES3-encoded output data. The TXDIV[1:0] bits in control register 0x07 are utilized to select divide by 128, 256, 384, or 512 operation. Channel status and user data for Channels 1 and 2 are input to the AES3 encoder via the corresponding Transmitter Access (TA) data buffers. The TA data buffers are in turn loaded from the User Access (UA) buffers, which are programmed via the SPI or I2C host interface, or loaded from the DIR Receiver Access (RA) data buffers. The source of the channel status and user data is selected utilizing the TXCUS[1:0] bits in control register 0x09. When the DIR is selected as the input source, the channel status and user data output from the DIT is delayed by one block in relation to the audio data. The validity (V) bit may be programmed using one of two sources. The VALSEL bit in control register 0x09 is utilized to select the validity data source for the DIT block. The default source is the VALID bit in control register 0x07, which is written via the SPI or I2C host interface. The validity bit may also be transferred from the AES3 decoder output of the DIR, where the V bit for the DIT subframes tracks the decoded DIR value frame by frame. The parity (P) bit will always be generated by the AES3 encoder internal parity generator logic, such that bits 4 through 31 of the AES3-encoded subframe are even parity. 28 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 The AES3 encoder output is connected to the output line driver and CMOS buffer source multiplexers. As shown in Figure 65, the source multiplexers allow the line driver or buffer to be driven by the AES3-encoded data from the DIT, or by the bypass multiplexer, which is associated with the outputs of the four differential input line receivers preceding the DIR core. The bypass multiplexer allows for one of the four line receiver outputs to be routed to the line driver or buffer output, thereby providing a bypass mode of operation. Both the line driver and CMOS output buffer include output disables, set by the TXOFF and AESOFF bits in control register 0x08. When the outputs are disabled, they are forced to a low logic state. The AES3 encoder includes an output mute function that sets all bits for both the Channel 1 and 2 audio and auxiliary data to zero. The preamble, V, U, and C bits are unaffected, while the P bit is recalculated. The mute function is controlled using the TXMUTE bit in control register 0x08. TXCLK Master Clock Source TXDIV[1:0] MCLK AESMUX RXCKO AESOFF AESOUT (pin 34) TXIS[1:0] Data Source From Receiver Access (RA) Buffer 2 To/From SPI or I C Host Interface From Receiver Access (RA) Buffer 2 To/From SPI or I C Host Interface Port A Port B DIR SRC LDMUX TXOFF User Access (UA) Buffers Transmitter Access (TA) Buffers Channel Status Channel Status User Data User Data TX+ (pin 32) AES3 Encoder TX- (pin 31) From Bypass Multiplexer Output BLS (pin 35) TXCUS[1:0] TXBTD SYNC (pin 36) TXMUTE BLSM Figure 65. Digital Interface Transmitter (DIT) Functional Block Diagram The AES3 encoder includes a block start input/output pin, BLS (pin 35). The BLS pin may be programmed as an input or output. The input/output state of the BLS pin is programmed using the BLSM bit in control register 0x07. By default, the BLS pin is configured as an input. As an input, the BLS pin may be utilized to force a block start condition, whereby the start of a new block of channel status and user data is initiated by generating a Z preamble for the next frame of data. The BLS input must be synchronized with the DIT internal SYNC clock. This clock is output on SYNC (pin 36). The SYNC clock rising edge is aligned with the start of each frame for the AES3-encoded data output by the DIT. Figure 66 illustrates the format required for an external block start signal, as well as indicating the format when the BLS pin is configured as an output. When the BLS pin is an output, the DIT generates the block start signal based upon the internal SYNC clock. For details regarding DIT control and status registers, as well as channel status and user data buffers, refer to the Control Registers and Channel Status and User Data Buffer Maps sections. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 29 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Block Start (Frame 0 starts here) SYNC BLS (input) BLS (output) Figure 66. DIT Block Start Timing DIGITAL INTERFACE RECEIVER (DIR) OPERATION The DIR performs AES3 decoding and clock recovery and provides the differential line receiver functions. The lock range of the DIR includes frame/sampling rates from 20kHz to 216kHz. Figure 67 shows the functional block diagram for the DIR. Four differential line receivers are utilized for signal conditioning the encoded input data streams. The receivers can be externally configured for either balanced or unbalanced cable interfaces, as well as interfacing with CMOS logic level inputs from optical receivers or external logic circuitry. See Figure 68 for a simplified schematic for the line receiver. External connections are discussed in the Receiver Input Interfacing section. 2 To SPI or I C Host Interface Reference Clock Source MCLK To DIT RXCLK RX1+ (pin 1) RX1- (pin 2) RXMUX[1:0] User Data Channel Status PLL1 RXCKI AES3 Decoder To DIT User Data Channel Status Receiver Access (RA) Buffers RX2+ (pin 3) RX2- (pin 4) RX3+ (pin 5) RX3- (pin 6) Pulse Generator RX4+ (pin 7) RX4- (pin 8) BYPMUX[1:0] LOCK (pin 11) To DIT Buffer and Line Driver PLL2 128fS 256fS 512fS Clock Divider Divide by 1, 2, 4, or 8 RXCKO (pin 12) User Access (UA) Buffers Data Stream De-Mux Ch.1 (Left) Audio RXCKOF[1:0] Error and Status Outputs Ch.2 (Right) Audio Receiver Sync Generator RCV_SYNC RXCKO Figure 67. Digital Interface Receiver (DIR) Functional Block Diagram 30 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 VDD33 24kW 24kW 3kW RX+ To Receiver Input and Bypass Multiplexers RX3kW 24kW 24kW DGND2 Figure 68. Differential Line Receiver Circuit The outputs of the four line receivers are connected to two 1-of-4 data selectors: the receiver input multiplexer and the bypass multiplexer. The input multiplexer selects one of the four line receiver outputs as the source for the AES3-encoded data stream to be processed by the DIR core. The bypass multiplexer is utilized to route a line receiver output to either the DIT line driver or CMOS buffered outputs, thereby bypassing all other internal circuitry. The bypass function is useful for simple signal distribution and routing applications. The DIR requires a reference clock, supplied by an external source applied at either the RXCKI (pin 13) or MCLK (pin 25) clock inputs. PLL1 multiplies the reference clock to a higher rate, which is utilized as the oversampling clock for the AES3 decoder. The decoder samples the AES3-encoded input stream in order to extract all of the audio and status data. The decoded data stream is sent on to a de-multiplexer, where audio and status data are separated for further processing and buffering. The pulse generator circuitry samples the encoded input data stream and generates a clock that is 16 times the frame/sampling rate (or fS). The 16fS clock is then processed by PLL2, which further multiplies the clock rate and provides low-pass filtering for jitter attenuation. The available PLL2 output clock rates include 512fS, 256fS, and 128fS. The maximum available PLL2 output clock rate for a given input sampling rate is estimated by internal logic and made available for readback via status register 0x13. The output of PLL2 may be divided by a factor of two, four, or eight, or simply passed through to the recovered master clock output, RXCKO (pin 12). The RXCKO clock is also be routed internally to other function blocks, where it may be further divided to create left/right word and bit clocks. The RXCKO output may be disabled and forced to a high-impedance state by means of a control register bit, allowing other tri-state buffered clocks to be tied to the same external circuit node, if needed. By default, the RXCKO output (pin 12) is disabled and forced to a high-impedance state. Figure 69 illustrates the frequency response of PLL2. Jitter attenuation starts at approximately 50kHz. Peaking is nominally 1dB, which is within the 2dB maximum allowed by the AES3 standard. The receiver jitter tolerance plot for the DIR is illustrated in Figure 70, along with the required AES3 jitter tolerance template. The DIR jitter tolerance satisfies the AES3 requirements, as well as the requirements set forth by the IEC60958-3 specification. Figure 70 was captured using a full-scale 24-bit, two-channel, AES3-encoded input stream with a 48kHz frame rate. The decoded audio data, along with the internally-generated sync clocks, may be routed to other function blocks, including Port A, Port B, the SRC, and/or the DIT. The decoded channel status and user data is buffered in the corresponding Receiver Access (RA) data buffers, then transferred to the corresponding User Access (UA) data buffers, where it may be read back through either the SPI or I2C serial host interface. The contents of the RA buffers may also be transferred to the DIT UA data buffers; see Figure 65. The channel status and user data bits may also be output serially through the general-purpose output pins, GPO[4:1]. Figure 71 illustrates the output format for the GPO pins when used for this purpose, along with the DIR block start (BLS) and frame synchronization (SYNC) clocks. The rising edges of the DIR SYNC clock output are aligned with the start of each frame for the received AES3 data. The DIR includes a dedicated, active low AES3 decoder and PLL2 lock output, named LOCK (pin 11). The lock output is active only when both the AES3 decoder and PLL2 indicate a lock condition. Additional DIR status flags may be output at the general-purpose output (GPO) pins, or accessed through the status registers via the SPI or I2C host interface. Refer to the General-Purpose Digital Outputs and Control Registers sections for additional information regarding the DIR status functions. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 31 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 2 0 Jitter Attenuation (dB) -2 -4 -6 -8 -10 -12 -14 -16 -18 -20 10 0 10 1 10 2 10 3 10 4 10 5 10 6 Jitter Frequency (Hz) 5 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 2 Input Jitter Amplitude 1 Output Jitter Amplitude 500m 200m Peak Jitter (UI) THD+N Ratio (dB) Figure 69. DIR Jitter Attenuation Characteristics 100m 50m 20m 10m 5m THD+N 20 2m 100 1k 1m 100k 10k Sinusoidal Jitter Frequency (Hz) Figure 70. DIR Jitter Tolerance Plot Block Start (Frame 0 Starts Here) BLS (output) SYNC (output) C or U data (output) Ch. 1 Ch. 2 Bit 0 Ch. 1 Ch. 2 Ch. 1 Bit 1 Ch. 2 Bit 2 Ch. 1 Ch. 2 Bit 4 1/4 Figure 71. DIR Channel Status and User Data Serial Output Format Via the GPO Pins ASYNCHRONOUS SAMPLE RATE CONVERTER (SRC) OPERATION The asynchronous SRC provides conversion from an arbitrary input sampling rate to a desired output sampling rate. The input and output sampling rates may be equal or different, within the bounds of a 1:16 to 16:1 32 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 input-to-output sampling ratio range. The input and output data sources may be completely asynchronous to one another; synchronous operation is also supported. The input-to-output sampling ratio is determined automatically using internal rate estimation logic, with the re-sampler being updated in real time without the need for programming. The SRC supports input and output sampling rates up to 216kHz, with audio data word lengths up to 24 bits. A functional block diagram for the SRC is shown in Figure 72. DEM[1:0] SRCIS[1:0] MUTE (pin 14) DDN TRACK AL[7:0] AR[7:0] OWL[1:0] IGRP[1:0] AUTODEM Audio Data Output Port A De-Emphasis Filter Port B Interpolation Filter Decimation Filter Re-Sampler INT_SYNC From Port A, Port B, or DIT DIR fSIN MCLK Reference Clock Rate Estimator fSOUT RXCKI RXCKO SRI[4:0] SRF[10:0] RATIO SRCCLK[1:0] RDY (pin 15) Figure 72. Asynchronous Sample Rate Converter (SRC) Functional Block Diagram The SRC receives a digital audio input from one of three data sources: Port A, Port B, or the DIR. By default, Port A is selected as the input source for the SRC. The output of the SRC may be connected to Port A, Port B, and/or the DIT. The SRC requires a reference clock, which may be sourced from either the MCLK (pin 25) or RXCKI (pin 13) clock inputs, or from the RXCKO recovered master clock output from the DIR block. The reference clock is utilized by the rate estimator to determine the input-to-output sampling ratio. By default, MCLK is selected as the reference clock source for the SRC. As part of the SRC rate estimation and re-sampling functions, two digital servo loops are employed, one for the input side and one for the output side. The servo loops operate in two modes: Fast and Slow. When a change in one or both of the sampling rates occurs, the servo loop(s) enter(s) Fast mode operation. When a servo loop has settled in Fast mode, it will then switch to Slow mode. When both the input and output servo loops have switched to Slow mode, the RDY output (pin 15) is forced low, indicating that the SRC has completed the rate estimation process. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 33 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 The input and output servo-loop frequency responses are shown in Figure 73 and Figure 74, respectively. The filter response for each servo loop rolls off at 80dB per decade. The servo loop corner frequencies scale proportionally with input or output sampling rates. The low corner frequency and sharp roll-off provide excellent jitter attenuation for the SRC block. Attenuation (dB) 0 -50 Fast Mode -100 Slow Mode -150 fS = 192kHz -200 10 -1 10 0 10 1 10 2 10 3 10 4 10 5 Frequency (Hz) Figure 73. Input Digital Servo-Loop Frequency Response Attenuation (dB) 0 -50 Fast Mode Slow Mode -100 -150 fS = 192kHz -200 10 -2 10 -1 10 0 10 1 10 2 10 3 10 4 10 5 Frequency (Hz) Figure 74. Output Digital Servo-Loop Frequency Response The SRC includes output soft muting and digital attenuation functions, providing artifact-free muting and output level control for the SRC output data. The mute function forces the SRC output data low by stepping the output attenuation from the current setting to an all-zero data output state. The mute function may be controlled by the MUTE input (pin 14), or the MUTE bit in control register 0x2D. Both the pin and control bit are active high, with the signals being combined by a logic OR function internally to generate the SRC output mute control signal. The MUTE control bit in control register 0x2D is disabled by default. The digital attenuation is programmable over a 0dB to -127.5dB range in 0.5dB steps, and may be controlled independently for the Left and Right channels. The attenuation level is set using control registers; by default, the level is 0dB. A tracking function is available, allowing the Left and Right channel attenuation data to be set to the same value by simply programming the Left channel attenuation register. The tracking mode is enabled or disabled using a control register bit. The tracking function is disabled by default. The SRC includes digital de-emphasis filtering for the audio input data. The de-emphasis filter provides normalization for 50/15s pre-emphasized audio data. The de-emphasis filter supports 32kHz, 44.1kHz, and 48kHz input sampling rates. The filter is controlled by the DEM0, DEM1, and AUTODEM bits in control register 0x2E. The DEM0 and DEM1 bits allow the user to manually configure the de-emphasis filter operation. By default, the de-emphasis filtering is disabled. The AUTODEM bit, when enabled, overrides the setting of the 34 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 DEM0 and DEM1 bits. The AUTODEM function automatically enables and disables the de-emphasis filter for the required sampling rate based upon the setting of the pre-emphasis and sampling frequency channel status bits in the AES3 or S/PDIF input data stream, which are decoded by the DIR block. The AUTODEM feature functions only when both 50/15s pre-emphasis and one of the three supported sampling rates (32kHz, 44.1kHz, or 48kHz) are decoded by the DIR. By default, the de-emphasis filter, including the AUTODEM function, is disabled. The group delay of the SRC interpolation function can be programmed to one of four settings. The actual length of the interpolation filter is unaltered, but the number of samples pre-buffered in the FIFO prior to the re-sampler function can be set to 64, 32, 16, or 8. The FIFO length directly impacts the latency and group delay. By default, the number of samples pre-buffered is set to 64. The decimation filter includes a direct down-sampling option. This option should only be used in cases where the output sampling rate is higher than the input sampling rate. The advantage of using the direct down-sampling option is that it results in zero latency operation, as it simply selects one out of every 16 samples from the re-sampler output without applying low-pass anti-aliasing filtering. By contrast, the decimation filter response adds 36.46875 samples of group delay. The disadvantage of the direct down-sampling option is that it cannot be used in cases where the output sampling rate is equal to or lower than the input sampling rate, since the lack of low-pass filtering results in aliasing. By default, the decimation filter is enabled, as the initial values of the input and output sampling rates may be unknown. The SRC includes two status registers that contain the integer and fractional parts of the input-to-output sampling ratio, which is derived by the SRC rate estimator circuitry. These registers can be read back any time the RDY output is low. When either the input or output sampling rate is known, the unknown sampling rate can be calculated using the contents of these status registers. The SRC provides a simple word length reduction mechanism for reducing 24-bit audio data to 20-, 18-, or 16-bit output word lengths. Word length reduction is performed utilizing triangular probability density function (or TPDF) dither. The OWL0 and OWL1 bits in control register 0x2F are utilized to set the SRC output word length. One note concerning the SRC output word length setting: when using the SRC output as the data source for either the Port A or Port B serial data outputs, and the audio serial port data format is set to Right-Justified, the word length set for the audio serial port format must match the word length set for the SRC output data. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 35 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 GENERAL-PURPOSE DIGITAL OUTPUTS The SRC4382 includes four general-purpose digital outputs, GPO1 through GPO4 (pins 26 through 29, respectively). A GPO pin may be programmed to a static high or low state. Alternatively, a GPO pin may be connected to one of 14 internal logic nodes, allowing the GPO pin to inherit the function of the selected signal. Control registers 0x1B through 0x1E are utilized to select the function of the GPO pins. For details regarding GPO output configuration, refer to the Control Registers section. Table 1 summarizes the available output options for the GPO pins. Table 1. General-Purpose Output Pin Configurations GPOn3 GPOn2 GPOn1 GPOn0 0 0 0 0 GPOn FUNCTION GPOn is forced Low (default). 0 0 0 1 GPOn is forced High. 0 0 1 0 SRC Interrupt Flag; Active Low 0 0 1 1 DIT Interrupt Flag; Active Low 0 1 0 0 DIR Interrupt Flag; Active Low 0 1 0 1 DIR 50/15s Emphasis Flag; Active Low 0 1 1 0 DIR Non-Audio Data Flag; Active High 0 1 1 1 DIR Non-Valid Data Flag; Active High 1 0 0 0 DIR Channel Status Data Serial Output 1 0 0 1 DIR User Data Serial Output 1 0 1 0 DIR Block Start Clock Output 1 0 1 1 DIR COPY Bit Output (0 = Copyright Asserted, 1 = Copyright Not Asserted) 1 1 0 0 DIR L (or Origination) Bit Output (0 = 1st Generation or Higher,1 = Original) 1 1 0 1 DIR Parity Error Flag; Active High 1 1 1 0 DIR Internal Sync Clock Output; may be used as the data clock for the Channel Status and User Data serial outputs. 1 1 1 1 DIT Internal Sync Clock HOST INTERFACE OPERATION: SERIAL PERIPHERAL INTERFACE (SPI) MODE The SRC4382 supports a 4-wire SPI port when the CPM input (pin 18) is forced low or tied to ground. The SPI port supports high-speed serial data transfers up to 40Mbps. Register and data buffer write and read operations are supported. The CS input (pin 19) serves as the active low chip select for the SPI port. The CS input must be forced low in order to write or read registers and data buffers. When CS is forced high, the data at the CDIN input (pin 21) is ignored, and the CDOUT output (pin 22) is forced to a high-impedance state. The CDIN input serves as the serial data input for the port; the CDOUT output serves as the serial data output. The CCLK input (pin 20) serves as the serial data clock for both the input and output data. Data is latched at the CDIN input on the rising edge of CCLK, while data is clocked out of the CDOUT output on the falling edge of CCLK. Figure 75 illustrates the SPI port protocol. Byte 0 is referred to as the command byte, where the most significant bit (or MSB) is the read/write bit. For the R/W bit, a '0' indicates a write operation, while a '1' indicates a read operation. The remaining seven bits of the command byte are utilized for the register address targeted by the write or read operation. Byte 1 is a don't care byte, and may be set to all zeroes. This byte is included in order to retain protocol compatibility with earlier Texas Instruments digital audio interface and sample rate converter products, including the DIT4096, DIT4192, the SRC418x series devices, and the SRC419x series devices. The SPI port supports write and read operations for multiple sequential register addresses through the implementation of an auto-increment mode. As shown in Figure 75, the auto-increment mode is invoked by simply holding the CS input low for multiple data bytes. The register address is automatically incremented after each data byte transferred, starting with the address specified by the command byte. 36 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Refer to the Electrical Characteristics: SPI Interface table and Figure 2 for specifications and a timing diagram that highlight the key parameters for SPI interface operation. Set CS = 1 here to write/read one register location. Hold CS = 0 to enable auto-increment mode. CS Header CDIN Byte 0 Register Data Byte 1 Byte 2 Byte 3 Byte N Register Data CDOUT Hi Z Hi Z Data for A[6:0] Data for A[6:0]+1 Data for A[2:0]+N CCLK Byte Definition Byte 0: MSB LSB R/W A6 A5 A4 A3 A2 A1 A0 Register Address Set to 0 for Write; Set to 1 for Read. Byte 1: Don't Care Byte 2 through Byte N: Register Data Figure 75. Serial Peripheral Interface (SPI) Protocol for the SRC4382 HOST INTERFACE OPERATION: PHILIPS I2C MODE The SRC4382 supports a 2-wire Philips I2C bus interface when CPM (pin 18) is forced high or pulled up to the VIO supply rail. The SRC4382 functions as a Slave-only device on the bus. Standard and Fast modes of operation are supported. Standard mode supports data rates up to 100kbps, while Fast mode supports data rates up to 400kbps. Fast mode is downward compatible with Standard mode, and these modes are sometimes referred to as Fast/Standard, or F/S mode. The I2C Bus Specification (Version 2.1, January 2000), available from Philips Semiconductor, provides the details for the bus protocol and implementation. It is assumed that the reader is familiar with this specification. Refer to the Electrical Characteristics: I2C Standard and Fast Modes table and Figure 3 for specifications and a timing diagram that highlight the key parameters for I2C interface operation. When the I2C mode is invoked, pin 20 becomes SCL (which serves as the bus clock) and pin 22 becomes SDA (which carries the bi-directional serial data for the bus). Pins 19 and 21 become A0 and A1, respectively, and function as the hardware configurable portion of the 7-bit slave address. The SRC4382 utilizes a 7-bit Slave address, see Figure 76(a). Bits A2 through A6 are fixed and bits A0 and A1 are hardware programmable using pins 19 and 21, respectively. The programmable bits allow for up to four SRC4382 devices to be connected to the same bus. The slave address is followed by the Register Address Byte, which points to a specific register or data buffer location in the SRC4382 register map. The register address byte is comprised of seven bits for the address, and one bit for enabling or disabling auto-increment operation, see Figure 76(b). Auto-increment mode allows multiple sequential register locations to be written to or read back in a single operation, and is especially useful for block write and read operations. Figure 77 illustrates the protocol for Standard and Fast mode Write operations. When writing a single register address, or multiple non-sequential register addresses, the single register write operation of Figure 77(a) may be used one or more times. When writing multiple sequential register addresses, the auto-increment mode of Figure 77(b) improves efficiency. The register address is automatically incremented by one for each successive byte of data transferred. Figure 78 illustrates the protocol for Standard and Fast mode Read operations. The current address read operation of Figure 78(a) assumes the value of the register address from the previously executed write or read operation, and is useful for polling a register address for status changes. Figure 78(b) and Figure 78(c) illustrate read operations for one or more random register addresses, with or without auto-increment mode enabled. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 37 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 First Byte After the START/RESTART Condition Slave Address LSB MSB A6 A5 A4 A3 A2 A1 A0 1 1 1 0 0 A1 A0 R/W Set by Pin 19 Set by Pin 21 (a) SRC4382 Slave Address MSB LSB INC A6 Auto-Increment 0 = Disabled 1 = Enabled A5 A4 A3 A2 A1 A0 (b) Register Address Byte Figure 76. SRC4382 Slave Address and Register Address Byte Definitions Byte 3 Register Data Byte 2 Register Address Byte with INC = 0 Byte 1 Slave Address with R/W = 0 S A A A P (a) Writing a Single Register Byte 2 Register Address Byte with INC = 1 Byte 1 Slave Address with R/W = 0 S A A Byte N Register Data For Address + N Byte 4 Register Data For Address + 1 Byte 3 Register Data A A A P (b) Writing Multiple Sequential Registers Using Auto-Increment Operation Legend S = START Condition A = Acknowledge P = STOP Condition Transfer from Master to Slave Transfer from Slave to Master Figure 77. Fast/Standard Mode Write Operations 38 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Byte 2 Register Address Byte with INC = 0 Byte 1 Slave Address with R/W = 1 S A A P (a) Current Address Read, Assumes the Register Address of the Previous Byte 1 Slave Address with R/W = 0 S Byte 2 Register Address Byte with INC = 0 A Byte 3 Slave Address with R/W = 1 Byte 4 Register Data A A R A P (b) Random Read Operation, Auto-Increment Disabled S Byte 3 Slave Address with R/W = 1 Byte 2 Register Address Byte with INC = 1 Byte 1 Slave Address with R/W = 0 A A R Byte N Register Data For Address + N Byte 4 Register Data A A A P (c) Random Read Operation, Auto-Increment Enabled Legend S = START Condition A = Acknowledge A = Not Acknowledge R = Repeated START P = STOP Condition Transfer from Master to Slave Transfer from Slave to Master Figure 78. Fast/Standard Mode Read Operations INTERRUPT OUTPUT The SRC4382 includes multiple internal status bits, many of which may be set to trigger an interrupt signal. The interrupt signal is output at INT (pin 23), which is an active low, open-drain output. The INT pin requires a pull-up resistor to the VIO supply rail. The value of the pull-up is not critical, but a 10k device should be sufficient for most applications. Figure 79 shows the interrupt output pin connection. The open-drain output allows interrupt pins from multiple SRC4382 devices to be connected in a wired OR configuration. SRC4382 MCU, DSP, or Logic VIO Interrupt Logic 10kW INT 23 Interrupt Input To the INT outputs for additional SRC4382 devices Figure 79. Interrupt Output Pin Connections Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 39 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 APPLICATIONS INFORMATION Typical application diagrams and power-supply connections are presented in this section to aid the customer in hardware designs employing the SRC4382 device. Figure 80 illustrates typical application connections for the SRC4382 using an SPI host interface. The SPI host will typically be a microcontroller, digital signal processor, or a programmable logic device. In addition to providing the SPI bus master, the host may be utilized to process interrupt and flag outputs from the SRC4382. The audio serial ports are connected to external digital audio devices, which may include data converters, digital signal processors, digital audio interface receivers/transmitters, or other logic devices. The DIR inputs and DIT outputs are connected to line, optical, or logic interfaces (see the Receiver Input Interfacing and Transmitter Output Interfacing sections). Master and DIR reference clock sources are also shown. Figure 81 illustrates typical application connections for the SRC4382 using an I2C bus interface. The I2C bus master will typically be a microcontroller, digital signal processor, or a programmable logic device. In addition to providing the I2C bus master, the host may be used to process interrupt and flag outputs from the SRC4382. Pull-up resistors are connected from SCL (pin 20) and SDA (pin 22) to the VIO supply rail. These pull-up resistors are required for the open drain outputs of the I2C interface. All other connections to the SRC4382 are the same as the SPI host case discussed previously. Figure 82 illustrates the recommended power-supply connections and bypassing for the SRC4382. In this case, it is assumed that the VIO, VDD33, and VCC supplies are powered from the same +3.3V power source. The VDD18 core supply is powered from a separate supply, or derived from the +3.3V supply using a linear voltage regulator, as illustrated with the optional regulator circuitry of Figure 82. The 0.1F bypass capacitors are surface-mount X7R ceramic, and should be located as close to the device as possible. These capacitors should be connected directly between the supply and corresponding ground pins of the SRC4382. The ground pin is then connected directly to the ground plane of the printed circuit board (PCB). The larger value capacitors, shown connected in parallel to the 0.1F capacitors, are recommended. At a minimum, there should at least be footprints on the PCB for installation of these larger capacitors, so that experiments can be run with and without the capacitors installed, in order to determine the effect on the measured performance of the SRC4382. The larger value capacitors can be surface-mount X7R multilayer ceramic or tantalum chip. The substrate ground, BGND (pin 44), should be connected by a PCB trace to AGND (pin 10). The AGND pin is then connected directly to the ground plane. This connection helps to reduce noise in the DIR section of the device, aiding the overall jitter and noise tolerance for the receiver. A series resistor is shown between the +3.3V supply and VCC (pin 9) connection. This resistor combines with the bypass capacitors to create a simple RC filter to remove higher frequency components from the VCC supply. The series resistor should be a metal film type for best filtering characteristics. As a substitute for the resistor, a ferrite bead can be utilized, although it may have to be physically large in order to contribute to the filtering. 40 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 SRC4382IPFB 37 38 39 40 41 42 43 44 45 46 47 48 Audio I/O Device Audio I/O Device BCKA LRCKA SDINA SDOUTA NC VIO DGND3 BGND SDOUTB SDINB LRCKB BCKB 1 2 3 4 5 6 7 8 9 10 11 12 From Digital Inputs (Line, Optical, Logic) DIR Recovered Clock SYNC BLS AESOUT VDD33 TX+ TXDGND2 GPO4 GPO3 GPO2 GPO1 MCLK RX1+ RX1RX2+ RX2RX3+ RX3RX4+ RX4VCC AGND LOCK RXCKO RST INT CDOUT CDIN CCLK CS CPM VDD18 DGND1 RDY MUTE RXCKI 36 35 34 33 32 31 30 29 28 27 26 25 To Host or External Logic To Digital Outputs (Line, Optical, Logic) To Host or External Logic 24 23 22 21 20 19 18 17 16 15 14 13 SPI Host Controller Master Clock 10kW VIO DIR Ref Clock NOTE: See Figure 82 for power-supply connections. Dashed lines denote optional connections to the host. Figure 80. Typical Application Diagram Using SPI Host Interface SRC4382IPFB 37 38 39 40 41 42 43 44 45 46 47 48 Audio I/O Device Audio I/O Device From Digital Inputs (Line, Optical, Logic) DIR Recovered Clock 1 2 3 4 5 6 7 8 9 10 11 12 BCKA LRCKA SDINA SDOUTA NC VIO DGND3 BGND SDOUTB SDINB LRCKB BCKB RX1+ RX1RX2+ RX2RX3+ RX3RX4+ RX4VCC AGND LOCK RXCKO SYNC BLS AESOUT VDD33 TX+ TXDGND2 GPO4 GPO3 GPO2 GPO1 MCLK RST INT SDA A1 SCL A0 CPM VDD18 DGND1 RDY MUTE RXCKI 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 To Host or External Logic To Digital Outputs (Line, Optical, Logic) To Host or External Logic 2 IC Host Controller Tie LO or HI 10kW Master Clock 2.7kW VIO DIR Ref Clock NOTE: See Figure 82 for power-supply connections. Dashed lines denote optional connections to the host. Figure 81. Typical Application Diagram Using I2C Host Interface Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 41 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 +3.3V 10mF + 44 R 0.1mF 43 42 SRC4382IPFB 33 9 + 10mF + 0.1mF 0.1mF 10 10mF 30 Connect pin 44 to pin 10. Pin 10 is then connected to the ground plane. +3.3V TPS79318DBVR 1 IN 3 EN OUT NR 16 GND 0.1mF 2 17 0.1mF 5 4 C 0.01mF 2.2mF + +1.8V Optional Regulator Circuit R may be set from 2W to 10W, or replaced by a ferrite bead. C may be set to 10mF, or not installed when using the optional regulator circuit. Figure 82. Recommended Power-Supply Connections DIGITAL AUDIO TRANSFORMER VENDORS Transformers are shown in this data sheet for both receiver and transmitter balanced and unbalanced line interface implementations. For the Texas Instruments Pro Audio evaluation modules, transformers from Scientific Conversion are utilized. In addition to Scientific Conversion, there are other vendors that offer transformer products for digital audio interface applications. Please refer to the following manufacturer web sites for details regarding their products and services. Other transformer vendors may also be available by searching catalog and/or Internet resources. * Scientific Conversion: http://scientificonversion.com * Schott Corporation: http://schottcorp.com * Pulse Engineering: http://pulseeng.com 42 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 RECEIVER INPUT INTERFACING This section details the recommended interfaces for the SRC4382 line receiver inputs. Balanced and unbalanced line interfaces, in addition to optical receiver and external logic interfacing, will be discussed. For professional digital audio interfaces, 110 balanced line interfaces are either required or preferred. Transformer coupling is commonly employed to provide isolation and to improve common-mode noise rejection. Figure 83 shows the recommended transformer-coupled balanced line receiver interface for the SRC4382. The transformer is specified for a 1:1 turn ratio, and should exhibit low inter-winding capacitance for best performance. Due to the DC bias on the line receiver inputs, 0.1F capacitors are utilized for AC-coupling the transformer to the line receiver inputs. On the line side of the transformer, an optional 0.1F capacitor is shown for cases where a DC bias may be applied at the transmitter side of the connection. The coupling capacitors should be surface-mount ceramic chip type with an X7R or C0G dielectric. C (1) 1:1 0.1mF To RX+ 3 Digital Input 110W Balanced 1 110W XLR To RX- 2 0.1mF (1) Insert a 0.1mF capacitor when blocking common-mode DC voltage. Figure 83. Transformer-Coupled Balanced Input Interface Unbalanced 75 coaxial cable interfaces are commonly employed in consumer and broadcast audio applications. Designs with and without transformer line coupling may be utilized. Figure 84(a) shows the recommended 75 transformer-coupled line interface, which shares many similarities to the balanced design shown in Figure 83. Once again, the transformer provides isolation and improved noise rejection. Figure 84(b) shows the transformer-free interface, which is commonly used for S/PDIF consumer connections. C (1) 1:1 0.1mF To RX+ Digital Input 75W Unbalanced (RCA or BNC connector) 75W To RX0.1mF (a) Transformer-Coupled Unbalanced Line Interface 0.1mF To RX+ Digital Input 75W Unbalanced (RCA or BNC connector) 75W To RX0.1mF (b) Unbalanced Line Interface Without Transformer (1) Insert a 0.1mF capacitor when blocking common-mode DC components. Figure 84. Unbalanced Line Input Interfaces Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 43 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Optical interfaces utilizing all-plastic fiber are commonly employed for consumer audio equipment where interconnections are less than 10m in length. Optical receiver modules utilized for a digital audio interface operate from either a single +3.3V or +5V supply and have a TTL-, CMOS-, or low-voltage CMOS-compatible logic output. Interfacing to +3.3V optical receivers is straightforward when the optical receiver supply is powered from the SRC4382 VDD33 power source, as shown in Figure 85. For the +5V optical receivers, the output high logic level may exceed the SRC4382 line receiver absolute maximum input voltage. A level translator is required, placed between the optical receiver output and the SRC4382 line receiver input. Figure 86 shows the recommended input circuit when interfacing a +5V optical receiver to the SRC4382 line receiver inputs. The Texas Instruments SN74LVC1G125 single buffer IC is operated from the same +3.3V supply used for SRC4382 VDD33 supply. This buffer includes a +5V tolerant digital input, and provides the logic level translation required for the interface. VDD33 All-Plastic (5 or 10 meters maximum) Optical (1) Receiver To RX+ To RX0.1mF (1) Toshiba TORX141 or equivalent. Figure 85. Interfacing to a +3.3V Optical Receiver Module SN74LVC1G125 or Equivalent +5V VDD33 5 All-Plastic (5 or 10 meters maximum) Optical (1) Receiver 2 4 3 To RX+ To RX- 1 0.1mF (1) Toshiba TORX173, TORX176, TORX179, or equivalent. Figure 86. Interfacing to a +5V Optical Receiver Module 44 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 The SRC4382 line receivers may also be driven directly from external logic or line receiver devices with TTL or CMOS outputs. If the logic driving the line receiver is operated from +3.3V, then logic level translation is not be required. However, if the external logic is operated from a power-supply voltage that exceeds the maximum VDD33 supply voltage of the SRC4382, or operates from a supply voltage lower than +3.3V, then level translation is required. Figure 87 shows the recommended logic level translation methods, utilizing buffers and level translators available from Texas Instruments. SN74LVC1G125 or Equivalent VDD33 5 2 From +5V Logic (TTL or CMOS) 4 3 To RX+ To RX- 1 0.1mF SN74AVC1T45 or Equivalent +1.8V or +2.5V 1 3 From +1.8V or +2.5V CMOS Logic VDD33 5 6 4 To RX+ To RX- 2 0.1mF Figure 87. CMOS/TTL Input Logic Interface TRANSMITTER OUTPUT INTERFACING This section details the recommended interfaces for the SRC4382 transmitter line driver and CMOS buffered outputs. Balanced and unbalanced line interfaces, in addition to optical transmitter and external logic interfacing, will be discussed. For professional digital audio interfaces, 110 balanced line interfaces are either required or preferred. Transformer coupling is commonly employed to provide isolation and to improve common-mode noise performance. Figure 88 shows the recommended transformer-coupled balanced line driver interface for the SRC4382. The transformer is specified for a 1:1 turn ratio, and should exhibit low inter-winding capacitance for best performance. To eliminate residual DC bias, a 0.1F capacitor is utilized for AC-coupling the transformer to the line driver outputs. The coupling capacitor should be a surface-mount ceramic chip type with an X7R or C0G dielectric. 110W TX+ 1:1 3 1 TX- 2 0.1mF Digital Output 110W Balanced XLR Figure 88. Transformer-Coupled Balanced Output Interface Unbalanced 75 coaxial cable interfaces are commonly employed in consumer and broadcast audio applications. Designs with and without transformer line coupling may be utilized. Figure 89(a) illustrates the recommended 75 transformer-coupled line driver interface, which shares many similarities to the balanced design shown in Figure 88. Figure 89(b) illustrates the transformer-free line driver interface, which is commonly used for S/PDIF consumer connections. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 45 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 0.1mF 1:1 R1 TX+ Digital Output 75W Unbalanced (RCA or BNC connector) R2 (a) Transformer-Coupled Unbalanced Output 0.1mF R1 TX+ Digital Output 75W Unbalanced (RCA or BNC connector) R2 (b) Unbalanced Output Without Transformer R1 and R2 are selected to achieve the desired output voltage level while maintaining the required 75W transmitter output impedance. The TX+ output impedance is negligible. Figure 89. Unbalanced Line Output Interfaces Optical interfaces utilizing all-plastic fiber are commonly employed for consumer audio equipment where interconnections are less than 10m in length. Most optical transmitter modules utilized for a digital audio interface operate from a single +3.3V or +5V supply and have a TTL-compatible logic input. The CMOS buffered transmitter output of the SRC4382, AESOUT (pin 34), is capable of driving the optical transmitter with VIO supply voltages down to +3.0V. If the VIO supply voltage is less than +3.0V, then level translation logic is required to drive the optical transmitter input. A good choice for this application is the Texas Instruments SN74AVC1T45 single bus transceiver. This device features two power-supply rails, one for the input side and one for the output side. For this application, the input side supply is powered from the VIO supply, while the output side is powered from a +3.3V supply. This will boost the logic high level to a voltage suitable for driving the TTL compatible input configuration. Figure 90 shows the recommended optical transmitter interface circuits. Optical (1) Transmitter AESOUT VIO All-Plastic Fiber (5 or 10 meters maximum) +3.3V 1 5 If VIO < +3.0V. 6 3 SN74AVC1T45 or Equivalent 4 2 (1) Toshiba TOTX141, TOTX173, TOTX176, TOTX179, or equivalent. Figure 90. Interfacing to an Optical Transmitter Module The AESOUT output may also be used to drive external logic or line driver devices directly. Figure 91 illustrates the recommended logic interface techniques, including connections with and without level translation. Figure 92 illustrates an external line driver interface utilizing the Texas Instruments SN75ALS191 dual differential line driver. If the VIO supply of the SRC4382 is set from +3.0V to +3.3V, no logic level translation is required between the AESOUT output and the line driver input. If the VIO supply voltage is below this range, then the optional logic level translation logic of Figure 92 is required. The SN75ALS191 dual line driver is especially useful in applications where simultaneous 75 and 110 line interfaces are required. 46 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Direct to external logic operating from the VIO supply. AESOUT +5V 5 2 4 3 To +5V Logic (VIO supply = +3.0V to +3.3V) 1 SN74AHCT1G125 or Equivalent Figure 91. CMOS/TTL Output Logic Interface +5V SN75ALS191 1 8 2 AESOUT 7 VIO +3.3V 1 5 3 6 If VIO < +3.0V. 6 4 3 5 SN74AVC1T45 or Equivalent To Balanced or Unbalanced Line Interface To Balanced or Unbalanced Line Interface 2 1 Figure 92. External Line Driver Interface Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 47 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 REGISTER AND DATA BUFFER ORGANIZATION The SRC4382 organizes the on-chip registers and data buffers into four pages. The currently active page is chosen by programming the Page Selection Register to the desired page number. The Page Selection Register is available on every register page at address 0x7F, allowing easy movement between pages. Table 2 indicates the page selection corresponding to the Page Selection Register value. Table 2. Register Page Selection Page Selection Register Value (Hex) Selected Register Page 00 Page 0, Control and Status Registers 01 Page 1, DIR Channel Status and User Data Buffers 02 Page 2, DIT Channel Status and User Data Buffers 03 Page 3, Reserved Register Page 0 contains the control registers utilized to configure the various function blocks within the SRC4382. In addition, status registers are provided for flag and error conditions, with many of the status bits capable of generating an interrupt signal when enabled. See Table 3 for the control and status register map. Register Page 1 contains the digital interface receiver (or DIR) channel status and user data buffers. These buffers correspond to the data contained in the C and U bits of the previously received block of the AES3-encoded data stream. The contents of these buffers may be read through the SPI or I2C serial host interface and processed as needed by the host system. See Table 5 for the DIR channel status buffer map, and Table 6 for the DIR user data buffer map. Register Page 2 contains the digital interface transmitter (or DIT) channel status and user data buffers. These buffers correspond to the data contained in the C and U bits of the transmitted AES3-encoded data stream. The contents of these buffers may be written through the SPI or I2C serial host interface to configure the C and U bits of the transmitted AES3 data stream. The buffers may also be read for verification by the host system. See Table 7 for the DIT channel status buffer map, and Table 8 for the DIT user data buffer map. Register Page 3 is reserved for factory test and verification purposes, and cannot be accessed without an unlock code. The unlock code remains private; the test modes disable normal operation of the device, and are not useful in customer applications. CONTROL REGISTERS See Table 3 for the control and status register map of the SRC4382. Register addresses 0x00 and 0x34 through 0x7E are reserved for factory or future use. All register addresses are expressed as hexadecimal numbers. The following pages provide detailed descriptions for each control and status register. 48 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Table 3. Control and Status Register Map (Register Page 0) ADDRESS (Hex) D7 (MSB) D6 D5 D4 D3 D2 D1 D0 REGISTER GROUP 01 RESET 0 PDALL PDPA PDPB PDTX PDRX PDSRC Power-Down and Reset 02 0 0 0 0 0 TX RX SRC Global Interrupt Status 03 0 AMUTE AOUTS1 AOUTS0 AM/S AFMT2 AFMT1 AFMT0 Port A Control 04 0 0 0 0 ACLK1 ACLK0 ADIV1 ADIV0 Port A Control 05 0 BMUTE BOUTS1 BOUTS0 BM/S BFMT2 BFMT1 BFMT0 Port B Control 06 0 0 0 0 BCLK1 BCLK0 BDIV1 BDIV0 Port B Control 07 TXCLK TXDIV1 TXDIV0 TXIS1 TXIS0 BLSM VALID BSSL Transmitter Control 08 BYPMUX1 BYPMUX0 AESMUX LDMUX TXBTD AESOFF TXMUTE TXOFF Transmitter Control 09 0 0 0 0 0 VALSEL TXCUS1 TXCUS0 Transmitter Control 0A 0 0 RATIO READY 0 0 TSLIP TBTI SRC and DIT Status 0B 0 0 MRATIO MREADY 0 0 MTSLIP MTBTI SRC and DIT Interrupt Mask 0C RATIOM1 RATIOM0 READYM1 READYM0 TSLIPM1 TSLIPM0 TBTIM1 TBTIM0 SRC and DIT Interrupt Mode 0D 0 0 0 RXBTD RXCLK 0 RXMUX1 RXMUX Receiver Control 0E 0 0 0 LOL RXAMLL RXCKOD1 RXCKOD0 RXCKOE Receiver Control 0F P3 P2 P1 P0 J5 J4 J3 J2 Receiver PLL Configuration 10 J1 J0 D13 D12 D11 D10 D9 D8 Receiver PLL Configuration 11 D7 D6 D5 D4 D3 D2 D1 D0 Receiver PLL Configuration 12 0 0 0 0 0 0 DTS CD/LD IEC61937 Non-PCM Audio Detection 13 0 0 0 0 0 0 RXCKR1 RXCKR0 Receiver Status 14 CSCRC PARITY VBIT BPERR QCHG UNLOCK QCRC RBTI Receiver Status 15 0 0 0 0 0 0 0 OSLIP Receiver Status 16 MCSCRC MPARITY MVBIT MBPERR MQCHG MUNLOCK MQCRC MRBTI Receiver Interrupt Mask 17 0 0 0 0 0 0 0 MOSLIP Receiver Interrupt Mask 18 QCHGM1 QCHGM0 UNLOCKM1 UNLOCKM0 QCRCM1 QCRCM0 RBTIM1 RBTIM0 Receiver Interrupt Mode Receiver Interrupt Mode 19 CSCRCM1 CSCRCM0 PARITYM1 PARITYM0 VBITM1 VBITM0 BPERRM1 BPERRM0 1A 0 0 0 0 0 0 OSLIPM1 OSLIPM0 Receiver Interrupt Mode 1B 0 0 0 0 GPO13 GPO12 GPO11 GPO10 General-Purpose Out (GPO1) 1C 0 0 0 0 GPO23 GPO22 GPO21 GPO20 General-Purpose Out (GPO2) 1D 0 0 0 0 GPO33 GPO32 GPO31 GPO30 General-Purpose Out (GPO3) 1E 0 0 0 0 GPO43 GPO42 GPO41 GPO40 General-Purpose Out (GPO4) 1F Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Audio CD Q-Channel Sub-Code 20 Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15 Audio CD Q-Channel Sub-Code 21 Q16 Q17 Q18 Q19 Q20 Q21 Q22 Q23 Audio CD Q-Channel Sub-Code 22 Q24 Q25 Q26 Q27 Q28 Q29 Q30 Q31 Audio CD Q-Channel Sub-Code 23 Q32 Q33 Q34 Q35 Q36 Q37 Q38 Q39 Audio CD Q-Channel Sub-Code 24 Q40 Q41 Q42 Q43 Q44 Q45 Q46 Q47 Audio CD Q-Channel Sub-Code 25 Q48 Q49 Q50 Q51 Q52 Q53 Q54 Q55 Audio CD Q-Channel Sub-Code 26 Q56 Q57 Q58 Q59 Q60 Q61 Q62 Q63 Audio CD Q-Channel Sub-Code 27 Q64 Q65 Q66 Q67 Q68 Q69 Q70 Q71 Audio CD Q-Channel Sub-Code 28 Q72 Q73 Q74 Q75 Q76 Q77 Q78 Q79 Audio CD Q-Channel Sub-Code 29 PC15 PC14 PC13 PC12 PC11 PC10 PC09 PC08 PC Burst Preamble, High Byte 2A PC07 PC06 PC05 PC04 PC03 PC02 PC01 PC00 PC Burst Preamble, Low Byte 2B PD15 PD14 PD13 PD12 PD11 PD10 PD09 PD08 PD Burst Preamble, High Byte 2C PD07 PD06 PD05 PD04 PD03 PD02 PD01 PD00 PD Burst Preamble, Low Byte 2D 0 TRACK 0 MUTE SRCCLK1 SRCCLK0 SRCIS1 SRCIS0 SRC Control 2E 0 0 AUTODEM DEM1 DEM0 DDN IGRP1 IGRP0 SRC Control 2F OWL1 OWL0 0 0 0 0 0 0 SRC Control 30 AL7 AL6 AL5 AL4 AL3 AL2 AL1 AL0 SRC Control 31 AR7 AR6 AR5 AR4 AR3 AR2 AR1 AR0 SRC Control 32 SRI4 SRI3 SRI2 SRI1 SRI0 SRF10 SRF9 SRF8 SRC Input: Output Ratio 33 SRF7 SRF6 SRF5 SRF4 SRF3 SRF2 SRF1 SRF0 SRC Input: Output Ratio 7F 0 0 0 0 0 0 PAGE1 PAGE0 Page Selection Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 49 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 50 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Register 01: Power-Down and Reset Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) RESET 0 PDALL PDPA PDPB PDTX PDRX PDSRC PDSRC Power-Down for the SRC Function Block This bit is utilized to power-down the SRC and associated functions. PDSRC PDRX SRC Power-Down Mode 0 Enabled (Default) 1 Disabled; the SRC function block will operate normally based upon the applicable control register settings. Power-Down for the Receiver Function Block This bit is utilized to power-down the DIR and associated functions. All receiver outputs are forced low. PDRX PDTX Receiver Power-Down Mode 0 Enabled (Default) 1 Disabled; the Receiver function block will operate normally based upon the applicable control register settings. Power-Down for the Transmitter Function Block This bit is utilized to power-down the DIT and associated functions. All transmitter outputs are forced low. PDTX PDPB Transmitter Power-Down Mode 0 Enabled (Default) 1 Disabled; the Transmitter function block will operate normally based upon the applicable control register settings. Power-Down for Serial Port B This bit is utilized to power-down the audio serial I/O Port B. All port outputs are forced low. PDPB PDPA Port B Power-Down Mode 0 Enabled (Default) 1 Disabled; Port B will operate normally based upon the applicable control register settings. Power-Down for Serial Port A This bit is utilized to power-down the audio serial I/O Port A. All port outputs are forced low. PDPA PDALL Port A Power-Down Mode 0 Enabled (Default) 1 Disabled; Port A will operate normally based upon the applicable control register settings. Power-Down for All Functions This bit is utilized to power-down all function blocks except the host interface port and the control and status registers. PDALL RESET All Function Power-Down Mode 0 Enabled (Default) 1 Disabled; all function blocks will operate normally based upon the applicable control register settings. Software Reset This bit is used to force a reset initialization sequence, and is equivalent to forcing an external reset via the RST input (pin 24). RESET Reset Function 0 Disabled (Default) 1 Enabled; all control registers will be reset to the default state. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 51 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Register 02: Global Interrupt Status (Read-Only) Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 0 0 TX RX SRC SRC SRC Function Block Interrupt Status (Active High) When set to 1, this bit indicates an active interrupt from the SRC function block. This bit is active high. The user should then read status register 0x0A in order to determine which of the sources has generated an interrupt. RX Receiver Function Block Interrupt Status (Active High) When set to 1, this bit indicates an active interrupt from the DIR function block. This bit is active high. The user should then read status registers 0x14 and 0x15 in order to determine which of the sources has generated an interrupt. TX Transmitter Function Block Interrupt Status (Active High) When set to 1, this bit indicates an active interrupt from the DIT function block. This bit is active high. The user should then read status register 0x0A in order to determine which of the sources has generated an interrupt. Register 03: Port A Control Register 1 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 AMUTE AOUTS1 AOUTS0 AM/S AFMT2 AFMT1 AFMT0 AFMT[2:0] Port A Audio Data Format These bits are used to set the audio input and output data format for Port A. Refer to the Audio Serial Port Operation section for illustrations of the supported data formats. Refer to the Electrical Characteristics: Audio Serial Ports table and Figure 1 for an applicable timing diagram and parameters. AFMT2 AFMT1 AFMT0 0 0 0 Audio Data Format 24-Bit Left-Justified (Default) 0 0 1 24-Bit Philips I2S 0 1 0 Unused 0 1 1 Unused 1 0 0 16-Bit Right-Justified 1 0 1 18-Bit Right-Justified 1 1 0 20-Bit Right-Justified 1 1 1 24-Bit Right-Justified Note: When the SRC is selected as the output data source for Port A and the data format for the port is set to Right-Justified, the proper word length must be selected in the Port A control registers such that it matches the corresponding SRC output data word length. Refer to control register 0x2F for the SRC output word length selection. AM/S Port A Slave/Master Mode This bit is used to set the audio clock mode for Port A to either Slave or Master. AM/S AOUTS[1:0] Slave/Master Mode 0 Slave mode; the LRCK and BCK clocks are inputs generated by an external digital audio source. (Default) 1 Master mode; the LRCK and BCK clocks are outputs, derived from the Port A master clock source. Port A Output Data Source These bits are used to select the output data source for Port A. The data is output at SDOUTA (pin 40). AMUTE AOUTS1 AOUTS0 0 0 Output Data Source Port A Input, for data loop back. (Default) 0 1 Port B Input 1 0 DIR 1 1 SRC Port A Output Mute This bit is used to mute the Port A audio data output. AMUTE 52 Output Mute 0 Disabled; SDOUTA is driven by the output data source. (Default) 1 Enabled; SDOUTA is forced low. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Register 04: Port A Control Register 2 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 0 ACLK1 ACLK0 ADIV1 ADIV0 ADIV[1:0] Port A Master Clock Divider These bits are used to set the master clock divider for generating the LRCKA clock for Port A when configured for Master mode operation. BCKA is always set to 64 times the LRCKA clock rate in Master mode. ACLK[1:0] ADIV1 ADIV0 0 0 Master Mode Clock Divider Divide By 128 (Default) 0 1 Divide By 256 1 0 Divide By 384 1 1 Divide By 512 Port A Master Clock Source These bits are used to set the master clock source for Port A when configured for Master mode operation. ACLK1 ACLK0 0 0 Master Clock Source MCLK (Default) 0 1 RXCKI 1 0 RXCKO 1 1 Reserved Register 05: Port B Control Register 1 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 BMUTE BOUTS1 BOUTS0 BM/S BFMT2 BFMT1 BFMT0 BFMT[2:0] Port B Audio Data Format These bits are used to set the audio input and output data format for Port B. Refer to the Audio Serial Port Operation section for illustrations of the supported data formats. Refer to the Electrical Characteristics: Audio Serial Ports table and Figure 1 for an applicable timing diagram and parameters. BFMT2 BFMT1 BFMT0 0 0 0 Audio Data Format 24-Bit Left-Justified (Default) 0 0 1 24-Bit Philips I2S 0 1 0 Unused 0 1 1 Unused 1 0 0 16-Bit Right-Justified 1 0 1 18-Bit Right-Justified 1 1 0 20-Bit Right-Justified 1 1 1 24-Bit Right-Justified Note: When the SRC is selected as the output data source for Port B and the data format for the port is set to Right-Justified, the proper word length must be selected in the Port B control registers such that it matches the corresponding SRC output data word length. Refer to control register 0x2F for the SRC output word length selection. BM/S Port B Slave/Master Mode This bit is used to set the audio clock mode for Port B to either Slave or Master. BM/S BOUTS[1:0] Slave/Master Mode 0 Slave mode; the LRCK and BCK clocks are generated by an external source. (Default) 1 Master mode; the LRCK and BCK clocks are derived from the Port A master clock source. Port B Output Source These bits are used to select the output data source for Port B. The data is output at SDOUTB (pin 45). BMUTE BOUTS1 BOUTS0 0 0 Output Data Source Port B Input, for data loop back. (Default) 0 1 Port A Input 1 0 DIR 1 1 SRC Port B Output Mute Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 53 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 This bit is used to mute the Port B audio data output. BMUTE Output Mute 0 Disabled; SDOUTB is driven by the output data source. (Default) 1 Enabled; SDOUTB is forced low. Register 06: Port B Control Register 2 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 0 BCLK1 BCLK0 BDIV1 BDIV0 BDIV[1:0] Port B Master Mode Clock Divider These bits are used to set the master clock divider for generating the LRCKB clock for Port B when configured for Master mode operation. BCKB is always set to 64 times the LRCKB clock rate in Master mode. BCLK[1:0] BDIV1 BDIV0 0 0 Master Mode Clock Divider Divide By 128 (Default) 0 1 Divide By 256 1 0 Divide By 384 1 1 Divide By 512 Port B Master Clock Source These bits are used to set the master clock source for Port B when configured for Master mode operation. BCLK1 BCLK0 0 0 Master Clock Source MCLK (Default) 0 1 RXCKI 1 0 RXCKO 1 1 Reserved Register 07: Transmitter Control Register 1 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) TXCLK TXDIV1 TXDIV0 TXIS1 TXIS0 BLSM VALID BSSL BSSL Block Start or Asynchronous Data Slip Interrupt Trigger Selection This bit is used to select the trigger source for the Transmitter TSLIP status and interrupt bit. BSSL VALID TSLIP Interrupt Trigger Source 0 Data Slip Condition (Default) 1 Block Start Condition Validity (V) Data Bit This bit may be used to set the validity (or V) data bit in the AES3-encoded output. Refer to the VALSEL bit in control register 0x09 for V-bit source selection. VALID BLSM Transmitted Validity (V) Bit Data 0 Indicates that the transmitted audio data is suitable for conversion to an analog signal or for further digital processing. (Default) 1 Indicates that the transmitted audio data is not suitable for conversion to an analog signal or for further digital processing. Transmitter Block Start Input/Output Mode This bit is used to select the input/output mode for the DIT block start pin, BLS (pin 35). 54 BLSM BLS Pin Mode 0 Input (Default) 1 Output Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com TXIS[1:0] SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Transmitter Input Data Source These bits are used to select the audio data source for the DIT function block. TXDIV[1:0] TXIS1 TXIS0 0 0 Output Word Length Port A (Default) 0 1 Port B 1 0 DIR 1 1 SRC Transmitter Master Clock Divider These bits are used to select the Transmitter master clock divider, which determines the output frame rate. TXCLK TXDIV1 TXDIV0 Clock Divider 0 0 Divide the master clock by 128. (Default) 0 1 Divide the master clock by 256. 1 0 Divide the master clock by 384. 1 1 Divide the master clock by 512. Transmitter Master Clock Source This bit is used to select the master clock source for the Transmitter block. TXCLK Transmitter Master Clock Source 0 MCLK Input (Default) 1 RXCKO; the recovered master clock from the DIR function block. Register 08: Transmitter Control Register 2 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) BYPMUX1 BYPMUX0 AESMUX LDMUX TXBTD AESOFF TXMUTE TXOFF TXOFF Transmitter Line Driver Output Enable This bit is used to enable or disable the TX+ (pin 32) and TX- (pin 31) line driver outputs. TXOFF TXMUTE Transmitter Line Driver 0 Enabled; the line driver outputs function normally. (Default) 1 Disabled; the line driver outputs are forced low. Transmitter Audio Data Mute This bit is used to set the 24 bits of audio and auxiliary data to all zeros for both Channels 1 and 2. TXMUTE AESOFF Transmitter Audio Data Mute 0 Disabled (Default) 1 Enabled; the audio data for both Channels 1 and 2 are set to all zeros. AESOUT Output Enable This bit is used to enable or disable the AESOUT (pin 34) buffered AES3-encoded CMOS logic level output. AESOFF TXBTD AESOUT Output 0 Enabled; the AESOUT pin functions normally. (Default) 1 Disabled; the AESOUT pin is forced low. Transmitter C and U Data Buffer Transfer Disable This bit is used to enable and disable buffer transfers between the DIT User Access (UA) and DIT Transmitter Access (TA) buffers for both channel status (C) and user (U) data. Buffer transfers may be disabled, allowing the user to write new C and U data to the UA buffers via the SPI or I2C serial host interface. Once updated, UA-to-TA buffer transfers may then be re-enabled, allowing the TA buffer to be updated and the new C and U data to be transmitted at the start of the next block. TXBTD User Access (UA) to Transmitter Access (TA) Buffer Transfers 0 Enabled (Default) 1 Disabled; allows the user to update DIT C and U data buffers. Note: The TXCUS0 and TXCUS1 bits in control register 0x09 must be set to a non-zero value in order for DIT UA buffer updates to occur. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 55 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 LDMUX Transmitter Line Driver Input Source Selection This bit is used to select the input source for the DIT differential line driver outputs. LDMUX AESMUX Line Driver Input Source 0 DIT AES3 Encoder Output (Default) 1 Bypass Multiplexer Output AESOUT CMOS Buffer Input Source Selection This bit is used to select the input source for the AESOUT CMOS logic level output. AESMUX BYPMUX[1:0] AESOUT Buffer Input Source 0 DIT AES3 Encoder Output (Default) 1 Bypass Multiplexer Output Bypass Multiplexer Source Selection These bits select the line receiver output to be utilized as the Bypass multiplexer data source. BYPMUX1 BYPMUX0 0 0 Line Receiver Output Selection RX1 (Default) 0 1 RX2 1 0 RX3 1 1 RX4 Register 09: Transmitter Control Register 3 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 0 0 VALSEL TXCUS1 TXCUS0 TXCUS[1:0] Transmitter Channel Status and User Data Source These bits select the source of the channel status (or C) data and user (or U) data which is used to load the DIT User Access (UA) buffers. VALSEL TXCUS1 TXCUS0 0 0 DIT UA Buffer Source The buffers will not be updated. (Default) 0 1 The buffers are updated via the SPI or I2C host interface. 1 0 The buffers are updated via the DIR RA buffers. 1 1 The first 10 bytes of the buffers are updated via the SPI or I2C host, while the remainder of the buffers are updated via the DIR RA buffers. Transmitter Validity Bit Source This bit is utilized to select the source for the validity (or V) bit in the AES3-encoded output data stream. VALSEL Validity (or V) Bit Source Selection 0 The VALID bit in control register 0x07. 1 The V bit is transferred from the DIR block with zero latency. Register 0A: SRC and DIT Status (Read-Only) Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 RATIO READY 0 0 TSLIP TBTI TBTI Transmitter Buffer Transfer Status, Active High When DIT User Access (UA) to Transmitter Access (TA) buffer transfers are enabled (the TXBTD bit in control register 0x08 is set to 0), and the TBTI interrupt is unmasked (the MTBTI bit in control register 0x0B is set to 1), the TBTI bit will be set to 1 when the UA-to-TA buffer transfer has completed. This configuration also causes the INT output (pin 23) to be driven low and the TX bit in status register 0x02 to be set to 1, indicating that an interrupt has occurred. TSLIP Transmitter Source Data Slip Status, Active High The TSLIP bit will be set to 1 when either an asynchronous data slip or block start condition is detected, and the TSLIP interrupt is unmasked (the MTSLIP bit in control register 0x0B is set to 1). The BSSL bit in control register 0x07 is used to set the source for this interrupt. The TSLIP bit being forced to 1 will also cause the INT output (pin 23) to be driven low and the TX bit in status register 0x02 to be set to 1, indicating that an interrupt has occurred. READY SRC Rate Estimator Ready Status, Active High The READY bit will be set to 1 when the input and output rate estimators have completed the Fast mode portion of the rate estimation process, and the READY interrupt is unmasked (the MREADY bit in control register 0x0B is set to 1). This will also cause the INT output (pin 23) to be driven low and the SRC bit in status register 0x02 to be set to 1, indicating that an interrupt has occurred. 56 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com RATIO SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 SRC Ratio Status, Active High The RATIO bit will be set to 1 when the input sampling rate is higher than the output sampling rate, and the RATIO interrupt is unmasked (the MRATIO bit in control register 0x0B is set to 1). This will also cause the INT output (pin 23) to be driven low and the SRC bit in status register 0x02 to be set to 1, indicating that an interrupt has occurred. Register 0B: SRC and DIT Interrupt Mask Register Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 MRATIO MREADY 0 0 MTSLIP MTBTI MBTI Transmitter Buffer Transfer Interrupt Mask MTBI MTSLIP BTI Interrupt Mask 0 BTI interrupt is masked. (Default) 1 BTI interrupt is enabled. Transmitter TSLIP Interrupt Mask MTSLIP MREADY TSLIP Interrupt Mask 0 TSLIP interrupt is masked. (Default) 1 TSLIP interrupt is enabled. SRC Ready Interrupt Mask MREADY MRATIO READY Interrupt Mask 0 READY interrupt is masked. (Default) 1 READY interrupt is enabled. SRC Ratio Interrupt Mask MRATIO RATIO Interrupt Mask 0 RATIO interrupt is masked. (Default) 1 RATIO interrupt is enabled. Register 0C: SRC and DIT Interrupt Mode Register Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) RATIOM1 RATIOM0 READYM1 READYM0 TSLIPM1 TSLIPM0 TBTIM1 TBTIM0 TBTIM[1:0] Transmitter Buffer Transfer Interrupt Mode These bits are utilized to select the active trigger state for the BTI interrupt. TSLIPM[1:0] TBTIM1 TBTIM0 0 0 Interrupt Active State Rising Edge Active (Default) 0 1 Falling Edge Active 1 0 Level Active 1 1 Reserved Transmitter Data Source Slip Interrupt Mode These bits are utilized to select the active trigger state for the TSLIP interrupt. TSLIPM1 TSLIPM0 0 0 Interrupt Active State Rising Edge Active (Default) 0 1 Falling Edge Active 1 0 Level Active 1 1 Reserved Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 57 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 READYM[1:0] SRC Ready Interrupt Mode These bits are utilized to select the active trigger state for the READY interrupt. RATIOM[1:0] READYM1 READYM0 0 0 Interrupt Active State Rising Edge Active (Default) 0 1 Falling Edge Active 1 0 Level Active 1 1 Reserved SRC Ratio Interrupt Mode These bits are utilized to select the active trigger state for the RATIO interrupt. RATIOM1 RATIOM0 Interrupt Active State 0 0 Rising Edge Active (Default) 0 1 Falling Edge Active 1 0 Level Active 1 1 Reserved Register 0D: Receiver Control Register 1 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 RXBTD RXCLK 0 RXMUX1 RXMUX0 RXMUX[1:0] Receiver Input Source Selection These bits are used to select the output of the line receiver to be used as the input data source for the DIR core. RXCLK RXMUX1 RXMUX0 0 0 Input Selection RX1 (Default) 0 1 RX2 1 0 RX3 1 1 RX4 Receiver Reference Clock Source This bit is used to select the reference clock source for PLL1 in the DIR core. RXCLK RXBTD Receiver Reference Clock 0 RXCKI (Default) 1 MCLK Receiver C and U Data Buffer Transfer Disable This bit is used to enable and disable buffer transfers between the Receiver Access (RA) and User Access (UA) buffers for both channel status (C) and user (U) data. Buffer transfers are typically disabled to allow the customer to read C and U data from the DIR UA buffer via the SPI or I2C serial host interface. Once read, the RA-to-UA buffer transfer can be re-enabled to allow the RA buffer to update the contents of the UA buffer in real time. RXBTD 58 Receiver Access (RA) to User Access (UA) Buffer Transfers 0 Enabled (Default) 1 Disabled; the user may read C and U data from the DIR UA buffers. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Register 0E: Receiver Control Register 2 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 LOL RXAMLL RXCKOD1 RXCKOD0 RXCKOE RXCKOE RXCKOE Output Enable This bit is used to enable or disable the recovered clock output, RXCKO (pin 12). When disabled, the output is set to a high-impedance state. RXCKOE RXCKOD[1:0] RXCKO Output State 0 Disabled; the RXCKO output is set to high-impedance. (Default) 1 Enabled; the recovered master clock is available at RXCKO. RXCKO Output Clock Divider These bits are utilized to set the clock divider at the output of PLL2. The output of the divider is the RXCKO clock, available internally or at the RXCKO output (pin 12). RXAMLL RXCKOD1 RXCKOD0 0 0 RXCKO Output Divider Passthrough, no division is performed. (Default) 0 1 Divide the PLL2 clock output by 2. 1 0 Divide the PLL2 clock output by 4. 1 1 Divide the PLL2 clock output by 8. Receiver Automatic Mute for Loss of Lock This bit is used to set the automatic mute function for the DIR block when a loss of lock is indicated by both the AES3 decoder and PLL2. RXAMLL LOL Receiver Auto-Mute Function 0 Disabled (Default) 1 Enabled; audio data output from the DIR block is forced low for a loss of lock condition. Receiver Loss of Lock Mode for the Recovered Clock (output from PLL2) This bit is used to set the mode of operation for PLL2 when a loss of lock condition occurs. LOL Receiver PLL2 Operation 0 The PLL2 output clock is stopped for a loss of lock condition. (Default) 1 The PLL2 output clock free runs when a loss of lock condition occurs. Register 0F: Receiver PLL1 Configuration Register 1 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) P3 P2 P1 P0 J5 J4 J3 J2 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) J1 J0 D13 D12 D11 D10 D9 D8 Register 10: Receiver PLL1 Configuration Register 2 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 59 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Register 11: Receiver PLL1 Configuration Register 3 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) D7 D6 D5 D4 D3 D2 D1 D0 Registers 0x0F through 0x11 are utilized to program PLL1 in the DIR core. PLL1 multiplies the DIR reference clock source to an oversampling rate which is adequate for AES3 decoder operation. PLL1 is programmed using the following relationship: (CLOCK K) / P = 98.304MHz where: CLOCK = frequency of the DIR reference clock source. K = J.D, where the integer part J = 1 to 63, and the fractional part D = 0 to 9999. P = the pre-divider value, which may be set to any 4-bit value that meets the conditions stated below. The following conditions must be met for the values of P, J, and D: If D = 0, then: If D 0, then: 2 MHz (CLOCK / P) 20 MHz and 4 J 55. 10 MHz (CLOCK / P) 20 MHz and 4 J 11. Referring to registers 0x0F through 0x11: P is programmed using bits P[3:0]. J is programmed using bits J[5:0]. D is programmed using bits D[13:0]. Table 4 shows values for P, J, and D for common DIR reference clock rates. Table 4. PLL1 Register Values for Common Reference Clock Rates REFERENCE CLOCK RATE (MHz) P J D ERROR (%) 8.1920 1 12 0 0.0000 11.2896 1 8 7075 0.0002 12.2880 1 8 0 0.0000 16.3840 1 6 0 0.0000 22.5792 2 8 7075 0.0002 24.5760 2 8 0 0.0000 27.0000 2 7 2818 0.0003 Register 12: Non-PCM Audio Detection Status Register (Read-Only) Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 0 0 0 DTS CD/LD IEC61937 IEC61937 This bit is utilized to indicate the detection of an IEC 61937 data reduced audio format (includes Dolby AC-3, DTS, etc.) for DVD playback or general transmission purposes. IEC61937 DTS CD/LD Data is not an IEC61937 format. 1 Data is an IEC61937 format. Refer to the PC and PD preamble registers (addresses 0x29 through 0x2C) for data type and burst length. This bit is used to indicate the detection of a DTS encoded audio compact disc (CD) or Laserdisc (LD) playback. DTS CD/LD 60 Status 0 Status 0 The CD/LD is not DTS encoded. 1 DTS CD/LD playback detected. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Register 13: Receiver Status Register 1 (Read-Only) Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 0 0 0 RXCKR1 RXCKR0 RXCKR[1:0] Maximum Available Recovered Clock Rate These two bits indicate the maximum available RXCKO clock rate based upon the DIR detection circuitry, which determines the frame rate of the incoming AES3-encoded bit stream. Based upon the estimated frame rate, a maximum rate for the recovered clock output (RXCKO) is determined and output from PLL2, as well as being loaded into the RXCKR0 and RXCKR1 status bits. The status of the RXCKR0 and RXCKR1 bits may be utilized to determine the programmed value for the PLL2 output clock divider, set by the RXCKOD0 and RXCKOD1 bits in control register 0x0E. RXCKR1 RXCKR0 0 0 Maximum Available RXCKO Rate Clock rate not determined. 0 1 128fS 1 0 256fS 1 1 512fS Register 14: Receiver Status Register 2 (Read-Only) Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) CSCRC PARITY VBIT BPERR QCHG UNLOCK QCRC RBTI Note: Status bits must be unmasked in control register 0x16 in order for the status interrupts to be generated. CSCRC Channel Status CRC Status CSCRC PARITY CRC Status 0 No Error 1 CRC Error Detected Parity Status PARITY VBIT Parity Status 0 No Error 1 Parity Error Detected Validity Bit Status VBIT BPERR Validity Bit 0 Valid Audio Data Indicated 1 Non-Valid Data Indicated Bipolar Encoding Error Status BPERR QCHG Bipolar Encoding Status 0 No Error 1 Bipolar Encoding Error Detected Q-Channel Sub-Code Data Change Status QCHG UNLOCK Q-Channel Data Status 0 No change in Q-channel sub-code data. 1 Q-channel data has changed. May be used to trigger a read of the Q-channel sub-code data, registers 0x1F through 0x28. DIR Unlock Error Status UNLOCK QCRC DIR Lock Status 0 No error; the DIR AES3 decoder and PLL2 are locked. 1 DIR lock error; the AES3 decoder and PLL2 are unlocked. Q-Channel Sub-Code CRC Status QCRC RBTI Q-Channel CRC Status 0 No Error 1 Q-channel sub-code data CRC error detected. Receiver Buffer Transfer Interrupt Status RBTI 0 DIR RA Buffer-to-UA Buffer Transfer Status Buffer Transfer Incomplete, or No Buffer Transfer Interrupt Indicated Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 61 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 1 Buffer Transfer Completed Register 15: Receiver Status Register 3 (Read-Only) Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 0 0 0 0 OSLIP Note: Status bits must be unmasked in control register 0x17 in order for the status interrupts to be generated. OSLIP Receiver Output Data Slip Error Status OSLIP Receiver OSLIP Error Status 0 No Error 1 DIR Output Data Slip/Repeat Error Detected An OSLIP interrupt is possible when the DIR output is used as the source for either the Port A or Port B audio serial port and the port is configured to operate in slave mode. Figure 93 shows the timing associated with the OSLIP interrupt. When only one audio serial port (Port A or Port B) is sourced by the DIR output, then the OSLIP status bit and interrupt applies to that port. If both Port A and Port B are sourced by the DIR output, then the OSLIP status bit and interrupt applies to Port A only. AES3 Bit Stream Y X X Y DIR SYNC R L R L LRCK, Left or Right Justified Formats (input) L R L R LRCK, I2S Format (input) L R L R 5% 5% Data Slip or Repeat may occur when the LRCK edges indicated are within the 5% window. Figure 93. DIR Output Slip/Repeat (OSLIP) Behavior Register 16: Receiver Interrupt Mask Register 1 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) MCSCRC MPARITY MVBIT MBPERR MQCHG MUNLOCK MQCRC MRBTI MCSCRC Channel Status CRC Error Interrupt Mask MCSCRC MPARITY Masked (Default) 1 Enabled Parity Error Interrupt Mask MPARITY MVBIT 62 Parity Error Interrupt 0 Masked (Default) 1 Enabled Validity Error Interrupt Mask MVBIT MBPERR CRC Interrupt 0 Validity Error Interrupt 0 Masked (Default) 1 Enabled Bipolar Encoding Error Interrupt Mask Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 MBPERR MQCHG Bipolar Error Interrupt 0 Masked (Default) 1 Enabled Q-Channel Sub-Code Data Change Interrupt Mask MQCHG MUNLOCK Q-Channel Data Change Interrupt 0 Masked (Default) 1 Enabled DIR Unlock Error Interrupt Mask MUNLOCK MQCRC DIR Unlock Interrupt 0 Masked (Default) 1 Enabled Q-Channel Sub-Code CRC Error Interrupt Mask MQCRC MRBTI Q-Channel CRC Error Interrupt 0 Masked (Default) 1 Enabled Receiver Buffer Transfer Interrupt Mask MRBTI Receiver Buffer Transfer Interrupt 0 Masked (Default) 1 Enabled Register 17: Receiver Interrupt Mask Register 2 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 0 0 0 0 MOSLIP MOSLIP Receiver Output Data Slip Error Mask MOSLIP Receiver OSLIP Error Interrupt 0 Masked (Default) 1 Enabled Register 18: Receiver Interrupt Mode Register 1 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) QCHGM1 QCHGM0 UNLOCKM1 UNLOCKM0 QCRCM1 QCRCM0 RBTIM1 RBTIM0 QCHGM[1:0] UNLOCKM[1:0] QCRCM[1:0] Q-Channel Sub-Code Data Change Interrupt Mode QCHGM1 QCHGM0 0 0 Interrupt Active State Rising Edge Active (Default) 0 1 Falling Edge Active 1 0 Level Active 1 1 Reserved DIR Unlock Error Interrupt Mode UNLOCKM1 UNLOCKM0 0 0 Interrupt Active State Rising Edge Active (Default) 0 1 Falling Edge Active 1 0 Level Active 1 1 Reserved Q-Channel Sub-Code CRC Error Interrupt Mode QCRCM1 QCRCM0 0 0 Interrupt Active State Rising Edge Active (Default) 0 1 Falling Edge Active 1 0 Level Active 1 1 Reserved Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 63 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 RBTIM[1:0] Receive Buffer Transfer Interrupt Mode RBTIM1 RBTIM0 0 0 Interrupt Active State Rising Edge Active (Default) 0 1 Falling Edge Active 1 0 Level Active 1 1 Reserved Register 19: Receiver Interrupt Mode Register 2 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) CSCRCM1 CSCRCM0 PARITYM1 PARITYM0 VBITM1 VBITM0 BPERRM1 BPERRM0 CSCRCM[1:0] PARITYM[1:0] VBITM[1:0] BPERRM[1:0] Channel Status CRC Error Interrupt Mode CSCRCM1 CSCRCM0 0 0 Interrupt Active State Rising Edge Active (Default) 0 1 Falling Edge Active 1 0 Level Active 1 1 Reserved Parity Error Interrupt Mode PARITYM1 PARITYM0 0 0 Interrupt Active State Rising Edge Active (Default) 0 1 Falling Edge Active 1 0 Level Active 1 1 Reserved Validity Error Interrupt Mode VBITM1 VBITM0 0 0 Interrupt Active State Rising Edge Active (Default) 0 1 Falling Edge Active 1 0 Level Active 1 1 Reserved Bipolar Encoding Error Interrupt Mode BPERRM1 BPERRM0 0 0 Interrupt Active State Rising Edge Active (Default) 0 1 Falling Edge Active 1 0 Level Active 1 1 Reserved Register 1A: Receiver Interrupt Mode Register 3 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 0 0 0 OSLIPM1 OSLIPM0 OSLIPM[1:0] 64 Receiver Output Data Slip Error Interrupt Mode OSLIPM1 OSLIPM0 0 0 Interrupt Active State Rising Edge Active (Default) 0 1 Falling Edge Active 1 0 Level Active 1 1 Reserved Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Register 1B: General-Purpose Output 1 (GPO1) Control Register Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 0 GPO13 GPO12 GPO11 GPO10 GPO[13:10] General-Purpose Output 1 (GPO1) Configuration These bits are used to set the state or data source for the general-purpose digital output pin GPO1. GPO13 GPO12 GPO11 GPO10 0 0 0 0 GPO1 Function GPO1 is Forced Low (Default) 0 0 0 1 GPO1 is Forced High 0 0 1 0 SRC Interrupt, Active Low 0 0 1 1 Transmitter Interrupt, Active Low 0 1 0 0 Receiver Interrupt, Active Low 0 1 0 1 Receiver 50/15s Pre-Emphasis, Active Low 0 1 1 0 Receiver Non-Audio Data, Active High 0 1 1 1 Receiver Non-Valid Data, Active High 1 0 0 0 Receiver Channel Status Bit 1 0 0 1 Receiver User Data Bit 1 0 1 0 Receiver Block Start Clock 1 0 1 1 Receiver COPY Bit (0 = Copyright Asserted, 1 = Copyright Not Asserted) 1 1 0 0 Receiver L-Bit (0 = First Generation or Higher, 1 = Original) 1 1 0 1 Receiver Parity Error, Active High 1 1 1 0 Receiver Internal Sync Clock 1 1 1 1 Transmitter Internal Sync Clock Register 1C: General-Purpose Output 2 (GPO2) Control Register Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 0 GPO23 GPO22 GPO21 GPO20 GPO[23:20] General-Purpose Output 2 (GPO2) Configuration These bits are used to set the state or data source for the general-purpose digital output pin GPO2. GPO23 GPO22 GPO21 GPO20 0 0 0 0 GPO2 Function GPO2 is Forced Low (Default) 0 0 0 1 GPO2 is Forced High 0 0 1 0 SRC Interrupt, Active Low 0 0 1 1 Transmitter Interrupt, Active Low 0 1 0 0 Receiver Interrupt, Active Low 0 1 0 1 Receiver 50/15s Pre-Emphasis, Active Low 0 1 1 0 Receiver Non-Audio Data, Active High 0 1 1 1 Receiver Non-Valid Data, Active High 1 0 0 0 Receiver Channel Status Bit 1 0 0 1 Receiver User Data Bit 1 0 1 0 Receiver Block Start Clock 1 0 1 1 Receiver COPY Bit (0 = Copyright Asserted, 1 = Copyright Not Asserted) 1 1 0 0 Receiver L-Bit (0 = First Generation or Higher, 1 = Original) 1 1 0 1 Receiver Parity Error, Active High 1 1 1 0 Receiver Internal Sync Clock 1 1 1 1 Transmitter Internal Sync Clock Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 65 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Register 1D: General-Purpose Output 3 (GPO3) Control Register Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 0 GPO33 GPO32 GPO31 GPO30 GPO[33:30] General-Purpose Output 3 (GPO3) Configuration These bits are used to set the state or data source for the general-purpose digital output pin GPO3. GPO33 GPO32 GPO31 GPO30 0 0 0 0 GPO3 Function GPO3 is Forced Low (Default) 0 0 0 1 GPO3 is Forced High 0 0 1 0 SRC Interrupt, Active Low 0 0 1 1 Transmitter Interrupt, Active Low 0 1 0 0 Receiver Interrupt, Active Low 0 1 0 1 Receiver 50/15s Pre-Emphasis, Active Low 0 1 1 0 Receiver Non-Audio Data, Active High 0 1 1 1 Receiver Non-Valid Data, Active High 1 0 0 0 Receiver Channel Status Bit 1 0 0 1 Receiver User Data Bit 1 0 1 0 Receiver Block Start Clock 1 0 1 1 Receiver COPY Bit (0 = Copyright Asserted, 1 = Copyright Not Asserted) 1 1 0 0 Receiver L-Bit (0 = First Generation or Higher, 1 = Original) 1 1 0 1 Receiver Parity Error, Active High 1 1 1 0 Receiver Internal Sync Clock 1 1 1 1 Transmitter Internal Sync Clock Register 1E: General-Purpose Output 4 (GPO4) Control Register Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 0 GPO43 GPO42 GPO41 GPO40 GPO[43:40] General-Purpose Output 4 (GPO4) Configuration These bits are used to set the state or data source for the general-purpose digital output pin GPO4. 66 GPO43 GPO42 GPO41 GPO40 0 0 0 0 GPO4 is Forced Low (Default) 0 0 0 1 GPO4 is Forced High 0 0 1 0 SRC Interrupt, Active Low 0 0 1 1 Transmitter Interrupt, Active Low 0 1 0 0 Receiver Interrupt, Active Low 0 1 0 1 Receiver 50/15s Pre-Emphasis, Active Low 0 1 1 0 Receiver Non-Audio Data, Active High 0 1 1 1 Receiver Non-Valid Data, Active High 1 0 0 0 Receiver Channel Status Bit 1 0 0 1 Receiver User Data Bit 1 0 1 0 Receiver Block Start Clock 1 0 1 1 Receiver COPY Bit (0 = Copyright Asserted, 1 = Copyright Not Asserted) 1 1 0 0 Receiver L-Bit (0 = First Generation or Higher, 1 = Original) 1 1 0 1 Receiver Parity Error, Active High 1 1 1 0 Receiver Internal Sync Clock 1 1 1 1 Transmitter Internal Sync Clock Submit Documentation Feedback GPO4 Function Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Registers 1F through 28: Q-Channel Sub-Code Data Registers Registers 0x1F through 0x28 comprise the Q-channel sub-code buffer, which may be accessed for audio CD playback. The Q-channel data provides information regarding the playback status for the current disc. The buffer data is decoded by the DIR block. Register 1F: Q-Channel Sub-Code Data Register 1 (Read-Only), Bits[7:0], Control and Address Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Register 20: Q-Channel Sub-Code Data Register 2 (Read-Only), Bits[15:8], Track Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15 Register 21: Q-Channel Sub-Code Data Register 3 (Read-Only), Bits[23:16], Index Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) Q16 Q17 Q18 Q19 Q20 Q21 Q22 Q23 Register 22: Q-Channel Sub-Code Data Register 4 (Read-Only), Bits[31:24], Minutes Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) Q24 Q25 Q26 Q27 Q28 Q29 Q30 Q31 Register 23: : Q-Channel Sub-Code Data Register 5 (Read-Only), Bits[39:32], Seconds Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) Q32 Q33 Q34 Q35 Q36 Q37 Q38 Q39 Register 24: : Q-Channel Sub-Code Data Register 6 (Read-Only), Bits[47:40], Frame Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) Q40 Q41 Q42 Q43 Q44 Q45 Q46 Q47 Register 25: Q-Channel Sub-Code Data Register 7 (Read-Only), Bits[55:48], Zero Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) Q48 Q49 Q50 Q51 Q52 Q53 Q54 Q55 Register 26: Q-Channel Sub-Code Data Register 8 (Read-Only), Bits[63:56], AMIN Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) Q56 Q57 Q58 Q59 Q60 Q61 Q62 Q63 Register 27: Q-Channel Sub-Code Data Register 9 (Read-Only), Bits[71:64], ASEC Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) Q64 Q65 Q66 Q67 Q68 Q69 Q70 Q71 Register 28: Q-Channel Sub-Code Data Register 10 (Read-Only), Bits[79:72], AFRAME Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) Q72 Q73 Q74 Q75 Q76 Q77 Q78 Q79 Registers 29 through 2C: IEC61937 PC/PD Burst Preamble The PC and PD burst preambles are part of the IEC61937 standard for transmission of data reduced, non-PCM audio over a standard two-channel interface (IEC60958). Examples of data-reduced formats include Dolby AC-3, DTS, various flavors of MPEG audio (including AAC), and Sony ATRAC. The PA and PB preambles provide synchronization data, and are fixed values of 0xF872 and 0x4E1F, respectively. The PC preamble indicates the type of data being carried by the interface and the PD preamble indicates the length of the burst, given as number of bits. Registers 0x29 through 0x2C contain the PC and PD preambles as decoded by the DIR block. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 67 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Register 29: Burst Preamble PC High-Byte Status Register (Read-Only) Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) PC15 PC14 PC13 PC12 PC11 PC10 PC09 PC08 Register 2A: Burst Preamble PC Low-Byte Status Register (Read-Only) Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) PC07 PC06 PC05 PC04 PC03 PC02 PC01 PC00 PC[4:0], Hex Data Type 00 Null 01 Dolby AC-3 02 Reserved 03 Pause 04 MPEG-1 Layer 1 05 MPEG-1 Layer 2 or 3, or MPEG-2 Without Extension 06 MPEG-2 Data With Extension 07 MPEG-2 AAC ADTS 08 MPEG-2 Layer 1 Low Sample Rate 09 MPEG-2 Layer 2 or 3 Low Sample Rate 0A Reserved 0B DTS Type 1 0C DTS Type 2 0D DTS Type 3 0E ATRAC 0F ATRAC2/3 10-1F Reserved Bits PC[6:5] are both set to 0. Bit PC[7] is an Error Flag, where: 0 = A valid burst-payload; 1 = Burst-payload may contain errors. Bits PC[12:8] are data-type dependent. Bits PC[15:13] indicate the stream number, which is set to 0. Register 2B: Burst Preamble PD High-Byte Status Register (Read-Only) Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) PD15 PD14 PD13 PD12 PD11 PD10 PD09 PD08 Register 2C: Burst Preamble PD Low-Byte Status Register (Read-Only) 68 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) PD07 PD06 PD05 PD04 PD03 PD02 PD01 PD00 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Register 2D: SRC Control Register 1 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 TRACK 0 MUTE SRCCLK1 SRCCLK0 SRCIS1 SRCIS0 SRCIS[1:0] SRC Input Data Source These bits select the input data source for the SRC. SRCCLK[1:0] SRCIS1 SRCIS0 0 0 Input Source Port A (Default) 0 1 Port B 1 0 DIR 1 1 Reserved SRC Reference Clock Source These bits select the reference clock source for the SRC. MUTE SRCCLK1 SRCCLK0 0 0 Reference Clock Source MCLK (Default) 0 1 RXCKI 1 0 RXCKO 1 1 Reserved SRC Output Soft Mute Function This bit enables or disables the SRC output soft mute function. MUTE TRACK Mute Function 0 Mute Disabled (Default) 1 Mute enabled; output data set to all zeros. SRC Digital Output Attenuation Tracking This bit enables or disables left and right channel attenuation tracking. TRACK Output Attenuation Tracking 0 Tracking Disabled (Default) The Left and Right channel attenuation is programmed separately using registers 0x30 and 0x31, respectively. 1 Tracking Enabled The Left channel attenuation setting is also used for the Right channel. The Right channel tracks the Left channel setting. Register 2E: SRC Control Register 2 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 AUTODEM DEM1 DEM0 DDN IGRP1 IGRP0 IGRP[1:0] SRC Interpolation Filter Group Delay These bits select the interpolation filter group delay by configuring the number of samples which are pre-buffered prior to the re-sampler function. DDN IGRP1 IGRP0 0 0 Number of Samples Pre-Buffered 64 Samples (Default) 0 1 32 Samples 1 0 16 Samples 1 1 8 Samples SRC Decimation Filter/Direct Down-Sampling Function This bit selects the mode of the decimation function, either true decimation filter or direct down-sampling without filtering. DDN Decimation Function 0 Decimation Filter (Default) 1 Direct Down Sampling Note: Direct down-sampling should only be used when the output sampling rate is higher than the input sampling rate. When the output sampling rate is equal to or lower than the input sampling rate, the Decimation Filter must be used in order to avoid aliasing. DEM[1:0] Digital De-Emphasis Filter, Manual Configuration Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 69 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 These bits are utilized to enable or disable the digital de-emphasis filter manually. The de-emphasis filter is intended to process 50/15s pre-emphasized audio material at the following input sampling rates: DEM1 DEM0 0 0 De-Emphasis Filter Function De-Emphasis Disabled (Default) 0 1 De-Emphasis Enabled for fS = 48kHz 1 0 De-Emphasis Enabled for fS = 44.1kHz 1 1 De-Emphasis Enabled for fS = 32kHz Note: When the AUTODEM bit is set to 1, the setting of the DEM0 and DEM1 bits are ignored. AUTODEM Automatic De-Emphasis Configuration This bit enables or disables the automatic de-emphasis function, which monitors the channel status bits from the DIR function block and determines whether de-emphasis is enabled and for which sampling frequency. This function is valid for only 50/15s pre-emphasized data and one of the three supported sampling rates (32kHz, 44.1kHz, or 48kHz). AUTODEM Automatic De-Emphasis Function 0 Disabled (Default) 1 Enabled Register 2F: SRC Control Register 3 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) OWL1 OWL0 0 0 0 0 0 0 OWL[1:0] SRC Output Word Length These bits select the word length for the SRC output data. The word length reduction is performed by utilizing triangular PDF dithering. OWL1 OWL0 0 0 SRC Output Word Length 24 Bits (Default) 0 1 20 Bits 1 0 18 Bits 1 1 16 Bits Note: When the SRC is selected as the output data source for Port A or B and the data format for the port is set to Right-Justified, the proper word length must be selected in the Port A or B control registers such that it matches the corresponding SRC output data word length set by the OWL0 and OWL1 bits. Register 30: SRC Control Register 4 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) AL7 AL6 AL5 AL4 AL3 AL2 AL1 AL0 These bits are utilized to configure the SRC digital output attenuation for the Left Channel when the TRACK bit in register 0x2D is set to 0. The attenuation setting for the Left channel also applies to the Right channel when TRACK bit in register 0x2D is set to 1. Output Attenuation (dB) = -N 0.5, where N = AL[7:0]DEC. Register 31: SRC Control Register 5 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) AR7 AR6 AR5 AR4 AR3 AR2 AR1 AR0 These bits are utilized to configure the SRC digital output attenuation for the Right Channel when the TRACK bit in register 0x2D is set to 0. Output Attenuation (dB) = -N 0.5, where N = AR[7:0]DEC. Register 32: SRC Ratio Readback Register (Read-Only) 70 Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) SRI4 SRI3 SRI2 SRI1 SRI0 SRF10 SRF9 SRF8 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Register 33: SRC Ratio Readback Register (Read-Only) Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) SRF7 SRF6 SRF5 SRF4 SRF3 SRF2 SRF1 SRF0 SRI[4:0] Integer Part of the Input-to-Output Sampling Ratio SRF[10:0] Fractional Part of the Input-to-Output Sampling Ratio In order to properly read back the ratio, these registers must be read back in sequence, starting with register 0x32. Register 7F: Page Selection Register Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) 0 0 0 0 0 0 PAGE1 PAGE0 PAGE[1:0] Page Selection These bits are utilized to select one of three register pages for write and/or read access via the SPI or I2C serial host interface. The Page Selection Register is present on every register page at address 0x7F, allowing movement between pages as necessary. PAGE1 PAGE0 0 0 Register/Buffer Page Selection Page 0, Control and Status Registers (Default) 0 1 Page 1, DIR Channel Status and User Data Buffers 1 0 Page 2, DIT Channel Status and User Data Buffers 1 1 Page 3, Reserved CHANNEL STATUS AND USER DATA BUFFER MAPS Table 5 through Table 8 show the buffer maps for the DIR and DIT channel status and user data buffers. For Table 5, the channel status byte definitions are dependent on the transmission mode, either Professional or Consumer. Bit 0 of Byte 0 defines the transmission mode, 0 for Consumer mode, and 1 for Professional mode. This is applicable for Table 5 and Table 6. For Table 7, the channel status byte definitions are dependent on the transmission mode, either Professional or Consumer. Bit 0 of Byte 0 defines the transmission mode, 0 for Consumer mode, and 1 for Professional mode. In Professional mode, Byte 23 for each channel is reserved for CRC data, which is automatically calculated and encoded by the DIT. There is no need to program Byte 23 for either channel in Professional mode. Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 71 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Table 5. DIR Channel Status Data Buffer Map (Register Page 1) ADDRESS (Hex) CHANNEL BYTE BIT 0 (MSB) BIT 1 BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 0 1 0 D0 D1 D2 D3 D4 D5 D6 D7 1 2 0 D0 D1 D2 D3 D4 D5 D6 D7 2 1 1 D0 D1 D2 D3 D4 D5 D6 D7 3 2 1 D0 D1 D2 D3 D4 D5 D6 D7 4 1 2 D0 D1 D2 D3 D4 D5 D6 D7 5 2 2 D0 D1 D2 D3 D4 D5 D6 D7 6 1 3 D0 D1 D2 D3 D4 D5 D6 D7 7 2 3 D0 D1 D2 D3 D4 D5 D6 D7 8 1 4 D0 D1 D2 D3 D4 D5 D6 D7 9 2 4 D0 D1 D2 D3 D4 D5 D6 D7 A 1 5 D0 D1 D2 D3 D4 D5 D6 D7 B 2 5 D0 D1 D2 D3 D4 D5 D6 D7 C 1 6 D0 D1 D2 D3 D4 D5 D6 D7 D 2 6 D0 D1 D2 D3 D4 D5 D6 D7 E 1 7 D0 D1 D2 D3 D4 D5 D6 D7 F 2 7 D0 D1 D2 D3 D4 D5 D6 D7 10 1 8 D0 D1 D2 D3 D4 D5 D6 D7 11 2 8 D0 D1 D2 D3 D4 D5 D6 D7 12 1 9 D0 D1 D2 D3 D4 D5 D6 D7 13 2 9 D0 D1 D2 D3 D4 D5 D6 D7 14 1 10 D0 D1 D2 D3 D4 D5 D6 D7 15 2 10 D0 D1 D2 D3 D4 D5 D6 D7 16 1 11 D0 D1 D2 D3 D4 D5 D6 D7 17 2 11 D0 D1 D2 D3 D4 D5 D6 D7 18 1 12 D0 D1 D2 D3 D4 D5 D6 D7 19 2 12 D0 D1 D2 D3 D4 D5 D6 D7 1A 1 13 D0 D1 D2 D3 D4 D5 D6 D7 1B 2 13 D0 D1 D2 D3 D4 D5 D6 D7 1C 1 14 D0 D1 D2 D3 D4 D5 D6 D7 1D 2 14 D0 D1 D2 D3 D4 D5 D6 D7 1E 1 15 D0 D1 D2 D3 D4 D5 D6 D7 1F 2 15 D0 D1 D2 D3 D4 D5 D6 D7 20 1 16 D0 D1 D2 D3 D4 D5 D6 D7 21 2 16 D0 D1 D2 D3 D4 D5 D6 D7 22 1 17 D0 D1 D2 D3 D4 D5 D6 D7 23 2 17 D0 D1 D2 D3 D4 D5 D6 D7 24 1 18 D0 D1 D2 D3 D4 D5 D6 D7 25 2 18 D0 D1 D2 D3 D4 D5 D6 D7 26 1 19 D0 D1 D2 D3 D4 D5 D6 D7 27 2 19 D0 D1 D2 D3 D4 D5 D6 D7 28 1 20 D0 D1 D2 D3 D4 D5 D6 D7 29 2 20 D0 D1 D2 D3 D4 D5 D6 D7 2A 1 21 D0 D1 D2 D3 D4 D5 D6 D7 2B 2 21 D0 D1 D2 D3 D4 D5 D6 D7 2C 1 22 D0 D1 D2 D3 D4 D5 D6 D7 2D 2 22 D0 D1 D2 D3 D4 D5 D6 D7 2E 1 23 D0 D1 D2 D3 D4 D5 D6 D7 2F 2 23 D0 D1 D2 D3 D4 D5 D6 D7 72 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Table 6. DIR User Data Buffer Map (Register Page 1) ADDRESS (Hex) CHANNEL BYTE BIT 0 (MSB) BIT 1 BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 40 1 0 D0 D1 D2 D3 D4 D5 D6 D7 41 2 0 D0 D1 D2 D3 D4 D5 D6 D7 42 1 1 D0 D1 D2 D3 D4 D5 D6 D7 43 2 1 D0 D1 D2 D3 D4 D5 D6 D7 44 1 2 D0 D1 D2 D3 D4 D5 D6 D7 45 2 2 D0 D1 D2 D3 D4 D5 D6 D7 46 1 3 D0 D1 D2 D3 D4 D5 D6 D7 47 2 3 D0 D1 D2 D3 D4 D5 D6 D7 48 1 4 D0 D1 D2 D3 D4 D5 D6 D7 49 2 4 D0 D1 D2 D3 D4 D5 D6 D7 4A 1 5 D0 D1 D2 D3 D4 D5 D6 D7 4B 2 5 D0 D1 D2 D3 D4 D5 D6 D7 4C 1 6 D0 D1 D2 D3 D4 D5 D6 D7 4D 2 6 D0 D1 D2 D3 D4 D5 D6 D7 4E 1 7 D0 D1 D2 D3 D4 D5 D6 D7 4F 2 7 D0 D1 D2 D3 D4 D5 D6 D7 50 1 8 D0 D1 D2 D3 D4 D5 D6 D7 51 2 8 D0 D1 D2 D3 D4 D5 D6 D7 52 1 9 D0 D1 D2 D3 D4 D5 D6 D7 53 2 9 D0 D1 D2 D3 D4 D5 D6 D7 54 1 10 D0 D1 D2 D3 D4 D5 D6 D7 55 2 10 D0 D1 D2 D3 D4 D5 D6 D7 56 1 11 D0 D1 D2 D3 D4 D5 D6 D7 57 2 11 D0 D1 D2 D3 D4 D5 D6 D7 58 1 12 D0 D1 D2 D3 D4 D5 D6 D7 59 2 12 D0 D1 D2 D3 D4 D5 D6 D7 5A 1 13 D0 D1 D2 D3 D4 D5 D6 D7 5B 2 13 D0 D1 D2 D3 D4 D5 D6 D7 5C 1 14 D0 D1 D2 D3 D4 D5 D6 D7 5D 2 14 D0 D1 D2 D3 D4 D5 D6 D7 5E 1 15 D0 D1 D2 D3 D4 D5 D6 D7 5F 2 15 D0 D1 D2 D3 D4 D5 D6 D7 60 1 16 D0 D1 D2 D3 D4 D5 D6 D7 61 2 16 D0 D1 D2 D3 D4 D5 D6 D7 62 1 17 D0 D1 D2 D3 D4 D5 D6 D7 63 2 17 D0 D1 D2 D3 D4 D5 D6 D7 64 1 18 D0 D1 D2 D3 D4 D5 D6 D7 65 2 18 D0 D1 D2 D3 D4 D5 D6 D7 66 1 19 D0 D1 D2 D3 D4 D5 D6 D7 67 2 19 D0 D1 D2 D3 D4 D5 D6 D7 68 1 20 D0 D1 D2 D3 D4 D5 D6 D7 69 2 20 D0 D1 D2 D3 D4 D5 D6 D7 6A 1 21 D0 D1 D2 D3 D4 D5 D6 D7 6B 2 21 D0 D1 D2 D3 D4 D5 D6 D7 6C 1 22 D0 D1 D2 D3 D4 D5 D6 D7 6D 2 22 D0 D1 D2 D3 D4 D5 D6 D7 6E 1 23 D0 D1 D2 D3 D4 D5 D6 D7 6F 2 23 D0 D1 D2 D3 D4 D5 D6 D7 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 73 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Table 7. DIT Channel Status Data Buffer Map (Register Page 2) ADDRESS (Hex) CHANNEL BYTE BIT 0 (MSB) BIT 1 BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 0 1 0 D0 D1 D2 D3 D4 D5 D6 D7 1 2 0 D0 D1 D2 D3 D4 D5 D6 D7 2 1 1 D0 D1 D2 D3 D4 D5 D6 D7 3 2 1 D0 D1 D2 D3 D4 D5 D6 D7 4 1 2 D0 D1 D2 D3 D4 D5 D6 D7 5 2 2 D0 D1 D2 D3 D4 D5 D6 D7 6 1 3 D0 D1 D2 D3 D4 D5 D6 D7 7 2 3 D0 D1 D2 D3 D4 D5 D6 D7 8 1 4 D0 D1 D2 D3 D4 D5 D6 D7 9 2 4 D0 D1 D2 D3 D4 D5 D6 D7 A 1 5 D0 D1 D2 D3 D4 D5 D6 D7 B 2 5 D0 D1 D2 D3 D4 D5 D6 D7 C 1 6 D0 D1 D2 D3 D4 D5 D6 D7 D 2 6 D0 D1 D2 D3 D4 D5 D6 D7 E 1 7 D0 D1 D2 D3 D4 D5 D6 D7 F 2 7 D0 D1 D2 D3 D4 D5 D6 D7 10 1 8 D0 D1 D2 D3 D4 D5 D6 D7 11 2 8 D0 D1 D2 D3 D4 D5 D6 D7 12 1 9 D0 D1 D2 D3 D4 D5 D6 D7 13 2 9 D0 D1 D2 D3 D4 D5 D6 D7 14 1 10 D0 D1 D2 D3 D4 D5 D6 D7 15 2 10 D0 D1 D2 D3 D4 D5 D6 D7 16 1 11 D0 D1 D2 D3 D4 D5 D6 D7 17 2 11 D0 D1 D2 D3 D4 D5 D6 D7 18 1 12 D0 D1 D2 D3 D4 D5 D6 D7 19 2 12 D0 D1 D2 D3 D4 D5 D6 D7 1A 1 13 D0 D1 D2 D3 D4 D5 D6 D7 1B 2 13 D0 D1 D2 D3 D4 D5 D6 D7 1C 1 14 D0 D1 D2 D3 D4 D5 D6 D7 1D 2 14 D0 D1 D2 D3 D4 D5 D6 D7 1E 1 15 D0 D1 D2 D3 D4 D5 D6 D7 1F 2 15 D0 D1 D2 D3 D4 D5 D6 D7 20 1 16 D0 D1 D2 D3 D4 D5 D6 D7 21 2 16 D0 D1 D2 D3 D4 D5 D6 D7 22 1 17 D0 D1 D2 D3 D4 D5 D6 D7 23 2 17 D0 D1 D2 D3 D4 D5 D6 D7 24 1 18 D0 D1 D2 D3 D4 D5 D6 D7 25 2 18 D0 D1 D2 D3 D4 D5 D6 D7 26 1 19 D0 D1 D2 D3 D4 D5 D6 D7 27 2 19 D0 D1 D2 D3 D4 D5 D6 D7 28 1 20 D0 D1 D2 D3 D4 D5 D6 D7 29 2 20 D0 D1 D2 D3 D4 D5 D6 D7 2A 1 21 D0 D1 D2 D3 D4 D5 D6 D7 2B 2 21 D0 D1 D2 D3 D4 D5 D6 D7 2C 1 22 D0 D1 D2 D3 D4 D5 D6 D7 2D 2 22 D0 D1 D2 D3 D4 D5 D6 D7 2E 1 23 D0 D1 D2 D3 D4 D5 D6 D7 2F 2 23 D0 D1 D2 D3 D4 D5 D6 D7 74 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 Table 8. DIT User Data Buffer Map (Register Page 2) ADDRESS (Hex) CHANNEL BYTE BIT 0 (MSB) BIT 1 BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 40 1 0 D0 D1 D2 D3 D4 D5 D6 D7 41 2 0 D0 D1 D2 D3 D4 D5 D6 D7 42 1 1 D0 D1 D2 D3 D4 D5 D6 D7 43 2 1 D0 D1 D2 D3 D4 D5 D6 D7 44 1 2 D0 D1 D2 D3 D4 D5 D6 D7 45 2 2 D0 D1 D2 D3 D4 D5 D6 D7 46 1 3 D0 D1 D2 D3 D4 D5 D6 D7 47 2 3 D0 D1 D2 D3 D4 D5 D6 D7 48 1 4 D0 D1 D2 D3 D4 D5 D6 D7 49 2 4 D0 D1 D2 D3 D4 D5 D6 D7 4A 1 5 D0 D1 D2 D3 D4 D5 D6 D7 4B 2 5 D0 D1 D2 D3 D4 D5 D6 D7 4C 1 6 D0 D1 D2 D3 D4 D5 D6 D7 4D 2 6 D0 D1 D2 D3 D4 D5 D6 D7 4E 1 7 D0 D1 D2 D3 D4 D5 D6 D7 4F 2 7 D0 D1 D2 D3 D4 D5 D6 D7 50 1 8 D0 D1 D2 D3 D4 D5 D6 D7 51 2 8 D0 D1 D2 D3 D4 D5 D6 D7 52 1 9 D0 D1 D2 D3 D4 D5 D6 D7 53 2 9 D0 D1 D2 D3 D4 D5 D6 D7 54 1 10 D0 D1 D2 D3 D4 D5 D6 D7 55 2 10 D0 D1 D2 D3 D4 D5 D6 D7 56 1 11 D0 D1 D2 D3 D4 D5 D6 D7 57 2 11 D0 D1 D2 D3 D4 D5 D6 D7 58 1 12 D0 D1 D2 D3 D4 D5 D6 D7 59 2 12 D0 D1 D2 D3 D4 D5 D6 D7 5A 1 13 D0 D1 D2 D3 D4 D5 D6 D7 5B 2 13 D0 D1 D2 D3 D4 D5 D6 D7 5C 1 14 D0 D1 D2 D3 D4 D5 D6 D7 5D 2 14 D0 D1 D2 D3 D4 D5 D6 D7 5E 1 15 D0 D1 D2 D3 D4 D5 D6 D7 5F 2 15 D0 D1 D2 D3 D4 D5 D6 D7 60 1 16 D0 D1 D2 D3 D4 D5 D6 D7 61 2 16 D0 D1 D2 D3 D4 D5 D6 D7 62 1 17 D0 D1 D2 D3 D4 D5 D6 D7 63 2 17 D0 D1 D2 D3 D4 D5 D6 D7 64 1 18 D0 D1 D2 D3 D4 D5 D6 D7 65 2 18 D0 D1 D2 D3 D4 D5 D6 D7 66 1 19 D0 D1 D2 D3 D4 D5 D6 D7 67 2 19 D0 D1 D2 D3 D4 D5 D6 D7 68 1 20 D0 D1 D2 D3 D4 D5 D6 D7 69 2 20 D0 D1 D2 D3 D4 D5 D6 D7 6A 1 21 D0 D1 D2 D3 D4 D5 D6 D7 6B 2 21 D0 D1 D2 D3 D4 D5 D6 D7 6C 1 22 D0 D1 D2 D3 D4 D5 D6 D7 6D 2 22 D0 D1 D2 D3 D4 D5 D6 D7 6E 1 23 D0 D1 D2 D3 D4 D5 D6 D7 6F 2 23 D0 D1 D2 D3 D4 D5 D6 D7 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 75 SRC4382 www.ti.com SBFS030C - JANUARY 2006 - REVISED SEPTEMBER 2007 REFERENCE DOCUMENTS Throughout this data sheet, various standards and documents are repeatedly cited as references. Sources for these documents are listed here so that the reader may obtain the documents for further study. Audio Engineering Society (AES) standards documents, including the AES3, AES11, AES18, and related specifications are available from the AES web site: http://www.aes.org. International Electrotechnical Committee (IEC) standards, including the IEC60958 and IEC61937 are available from the IEC web site: http://www.iec.ch; or the ANSI web site: http://www.ansi.org. The EIAJ CP-1212 (formerly CP-1201) standard is available from the Japanese Electronics and Information Technologies Industries Association (JEITA): http://www.jeita.or.jp/english. The Philips I2C bus specification is available from Philips: http://www.philips.com.The version utilized as a reference for this product is Version 2.1, published in January 2000. Several papers regarding balanced and unbalanced transformer-coupled digital audio interfaces have been published and presented at past AES conventions by Jon D. Paul of Scientific Conversion, Inc. These papers are available for download from: http://www.scientificonversion.com. Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. DATE REV PAGE -- 4/06 B SECTION -- DESCRIPTION Changed from Product Preview to Production Data. 12 Typical Characteristics Corrected spelling of Typical. 35 Product Overview, Asynchronous Sample Rate Converter Operation Figure 74: Corrected alignment of text. 40 Product Overview, Interrupt Output Figure 79: Changed reference to multiple SRC4392 devices. Corrected spelling error. 45 Applications Information, Receiver Input Interfacing Figure 85, Figure 86: Corrected spelling errors. 47 Applications Information, Transmitter Output Interfacing Figure 89, Figure 90: Corrected spelling errors. Figure 90: Renamed Optical Receiver block to Optical Transmitter. 49 Applications Information, Control Registers Changed wording in paragraph describing Control Registers to accurately explain which register addresses are reserved for factory or future use. Global -- Corrected punctuation errors: AES3-encoded, transformer-coupled. Changes from Revision B (April 2006) to Revision C .................................................................................................... Page * 76 Added U.S. patent number to front page............................................................................................................................... 1 Submit Documentation Feedback Copyright (c) 2006-2007, Texas Instruments Incorporated Product Folder Link(s): SRC4382 PACKAGE OPTION ADDENDUM www.ti.com 2-Mar-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SRC4382IPFB ACTIVE TQFP PFB 48 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SRC4382IPFBG4 ACTIVE TQFP PFB 48 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SRC4382IPFBR ACTIVE TQFP PFB 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SRC4382IPFBRG4 ACTIVE TQFP PFB 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device SRC4382IPFBR Package Package Pins Type Drawing TQFP PFB 48 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 1000 330.0 16.4 Pack Materials-Page 1 9.6 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 9.6 1.5 12.0 16.0 Q2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SRC4382IPFBR TQFP PFB 48 1000 367.0 367.0 38.0 Pack Materials-Page 2 MECHANICAL DATA MTQF019A - JANUARY 1995 - REVISED JANUARY 1998 PFB (S-PQFP-G48) PLASTIC QUAD FLATPACK 0,27 0,17 0,50 36 0,08 M 25 37 24 48 13 0,13 NOM 1 12 5,50 TYP 7,20 SQ 6,80 9,20 SQ 8,80 Gage Plane 0,25 0,05 MIN 0- 7 1,05 0,95 Seating Plane 0,75 0,45 0,08 1,20 MAX 4073176 / B 10/96 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Falls within JEDEC MS-026 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated