MC12 SERIES Metallized Polycarbonate Polycarbonate Wrap & Fill Tubular Metallized Polycarbonate Wrap and Fill Tubular FEATURES - High Capacitance Density - Low Temperature - High Insulation Resistance - Dissipation factor less than 0.3% - Excellent Retrace STANDARD CONFIGURATION - Wrap and tubular axial leads with Rev. 4 Summary Quality Control Capacitors are tested 100% for: Capacitance Range 0.001F to 20.0F Capacitance Tolerance Standard tolerance is 10%. Tolerances of 5%,2% and 1% are available. Operating Temperature Range -55C to +125C Enclosure/ Construction Extended metallized polycarbonate (non-inductive). Voltage Rating DC working voltage ratings at +125C, 100VDC, 200VDC, and 400VDC. o Capacitance o Tolerance o Dissipation Factor o Dielectric withstanding voltage o Insulation Resistance o Equivalent Series Resistance (ESR) Process and inspection data are maintained on on special request. and available Environmental Parameter Vibration Immersion Shock Humidity Thermal Shock Life Method 204 104 213 106 107 108 Reference MIL-STD-202 Condition D B I A F Characteristics Insulation Resistance Temperature(C) 25 Megaohmsx 50,000 Microfarads 85 5,000 125 500 Insulation Resistance Capacitance Change Temperature(C) -55 PercentageChange -2.5 (typical) 25 0 85 1.0 125 2.0 CapacitanceChange Dissipation Factor When measured at 1kHz, the dissipation factor shall not exceed 0.3% from +25C to +125C. Dielectric Strength Capacitors withstand a DC potential of 200% rated voltage for two (2) minutes without damage or breakdown. Test voltage must be applied and discharged through a resistance of 1 OHM per volt. minimum, and at 25C. Rev. 4 DATA EC PART NUMBER MFD MC12_102_ MC12_122_ MC12_152_ MC12_182_ MC12_222_ MC12_272_ MC12_332_ MC12_392_ MC12_472_ MC12_562_ MC12_682_ MC12_822_ MC12_103_ MC12_123_ MC12_153_ MC12_183_ MC12_223_ MC12_273_ MC12_333_ MC12_393_ MC12_473_ MC12_563_ MC12_683_ MC12_823_ MC12_104_ MC12_124_ MC12_154_ MC12_184_ MC12_224_ MC12_274_ MC12_334_ MC12_394_ MC12_474_ MC12_564_ MC12_684_ MC12_824_ MC12_105_ MC12_125_ MC12_155_ MC12_185_ MC12_205_ MC12_255_ MC12_305_ MC12_355_ MC12_405_ MC12_455_ MC12_505_ MC12_605_ MC12_805_ 0.0010 0.0012 0.0015 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.0056 0.0068 0.0082 0.0100 0.0120 0.0150 0.0180 0.0220 0.0270 0.0330 0.0390 0.0470 0.0560 0.0680 0.0820 0.1000 0.1200 0.1500 0.1800 0.2200 0.2700 0.3300 0.3900 0.4700 0.5600 0.6800 0.8200 1.0000 1.2000 1.5000 1.8000 2.0000 2.5000 3.0000 3.5000 4.0000 4.5000 5.0000 6.0000 8.0000 Note: The D 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.16 0.18 0.15 0.16 0.17 0.19 0.20 0.22 0.24 0.26 0.29 0.26 0.29 0.29 0.31 0.34 0.37 0.37 0.40 0.38 0.42 0.45 0.48 0.52 0.55 0.58 0.62 0.63 100 VDC D L 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.68 0.68 0.78 0.78 0.78 0.78 0.95 0.95 1.17 1.17 1.17 1.17 1.17 1.17 1.17 1.17 1.45 AWG 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 22 22 22 22 22 22 20 20 20 20 20 20 D 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.16 0.17 0.15 0.15 0.16 0.18 0.19 0.21 0.23 0.25 0.27 0.31 0.29 0.32 0.32 0.35 0.38 0.41 0.39 0.36 0.39 0.44 0.48 0.53 0.58 0.61 0.62 0.61 0.66 0.66 0.70 0.73 0.80 0.92 200 VDC F L 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.68 0.68 0.78 0.78 0.78 0.78 0.95 1.17 1.17 1.17 1.17 1.17 1.17 1.17 1.45 1.7 1.7 1.9 1.9 1.9 1.9 1.9 AWG 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 22 22 22 22 22 22 22 20 20 20 20 20 20 20 20 20 20 20 20 D 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.16 0.17 0.15 0.15 0.15 0.17 0.18 0.20 0.22 0.24 0.27 0.29 0.27 0.30 0.33 0.32 0.35 0.38 0.41 0.40 0.44 0.41 0.45 0.50 0.54 0.59 0.64 0.65 0.63 0.66 0.72 0.80 0.87 0.92 - 400 VDC J L 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.68 0.68 0.68 0.78 0.78 0.78 0.78 0.95 0.95 1.17 1.17 1.17 1.17 1.17 1.17 1.45 1.70 1.90 1.90 1.90 1.90 1.90 - AWG 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 22 22 22 22 22 20 20 20 20 20 20 20 20 20 20 20 20 20 - characterof thepartnumberrepresentstheDC voltagerating(i.e. D=100VDC, F=200VDC, etc.). Additonally, thetenth characterof thepartnumberrepresentstheTolerance (K= 10%, J=5%, G=2%, F=1%). Rev. 4 EC PART NUMBER MFD MC12_106_ MC12_126_ MC12_156_ MC12_186_ MC12_206_ 10.0000 12.0000 15.0000 18.0000 20.0000 Note: The D 0.64 0.65 0.72 0.78 0.82 100 VDC D L 1.7 1.9 1.9 1.9 1.9 AWG 20 20 20 20 20 200 VDC F D L 1.02 1.9 - AWG 20 - D - 400 VDC J L - AWG - characterof thepartnumberrepresentstheDC voltagerating(i.e. D=100VDC, F=200VDC, etc.). Additonally, thetenth characterof thepartnumberrepresentstheTolerance (K= 10%, J=5%, G=2%, F=1%). DATA Rev. 4 INFORMATION Polycarbonate capacitors are the superior choice for a wide range of electronic applications. That's why they've gained such broad acceptance and the choice of circuit designers for decades. Now And we're being told, that no longer is anyone going to produce the right grade of polycarbonate once existing inventories are gone, well, these polycarbonate capacitors will be a thing of the past. NOT in house. We always have, and we plan to continue to be TRUE! We produce our own polycarbonate a source. So, now you don't have to make that change, or be forced to settle for a substitute capacitor that doesn't the combined advantages of performance, reliability, compact size and cost! Type MC12 is a versatile metallized polycarbonate capacitor in a wrap and tubular with axial leads, designed for the following typical applications:commercial-industrial including analog and timing circuits, high frequency, and networks. TO ORDER TYPE MC12 Metallized Polycarbonate Dielectric STYLE / VOLTAGE D DC Voltage Rating: D=100VDC, F=200VDC, J=400VDC CAPACITANCE IN PICO FARADS Expressed in Picofarades, the third is the number of zeros. two digits are The TOLERANCE 106 K K=10% Also available: J=5%, G=2%, F=1% Marking and Date Code All capacitors are marked with company initials "EC", corporate logo or EC trademark--in addition to type MC12, capacitance, two digits of the date code represent the year, the second two digits the tolerance, rated DC working voltage and date code. The week, i.e., 0952 is the 52nd week of 2009, 0902 is the second week of 2009. Quality Assurance Major emphasis is placed on quality assurance. EC is an ISO 9001-2000 and AS9100:2004 Company. Raw material inspection and the use of SPC manufacturing procedures assure the highest quality standards. Procedures are fully described in the EC Quality Control Manual. Electronic Concepts will continue to advance the state-of-the-art by utilizing leading edge technology, compact capacitor designs and establishing reliability procedures. United States Eastern: *Headquarters* P.O. Box 1278 Eatontown,NJ 07724 Tel: 732-542-7880 Fax: 732-542-0524 Central: Illinois 630-668-8747 Europe Ireland Electronic ConceptsEurope LTD IDA Estate, Oughterad Co. Galway, Ireland tel: +353-91-552385,552432 fax: +353-91-552387 email: sales@ecicaps.ie website:www.electronicconcepts.ie email: sales@ecicaps.com website:www.ecicaps.com Rev. 4