CONDUCTIVE POLYMER CHIP CAPACITORS T530 SERIES - High Capacitance/Ultra-Low ESR FEATURES 100% Accelerated Steady State Aging 100% Surge Current Testing Utilizes Multiple Tantalum Anode Technology Volumetric Efficiency Use Up to 90% of Rated Voltage (10% Derating) Self-Healing Mechanism True SMT Capability RoHS Compliant/Lead Free * * * * * * * * Conductive Polymer Surface Mount Highest CV in Standard EIA Size Extremely Low ESR Operating Temperature: -55C to 125C Polymer Cathode Technology High Frequency Capacitance Retention Non-Ignition Failure Mode Capacitance: 150 to 1500 F Voltage: 2.5V to 10V Molded Case (pick-and-place precision) * * * * * * * * * OUTLINE DRAWINGS CATHODE (-) END VIEW SIDE VIEW ANODE (+) END VIEW B W BOTTOM VIEW B H E K T S X F P G S R Termination cutout at KEMETs Option, either end A L DIMENSIONS - MILLIMETERS (INCHES) Case Size KEMET D Y X EIA 7343-31 7343-40 7373-43 L W H F 0.1 S 0.3 X (Ref) T (Ref) A (Min) G (Ref) E (Ref) 7.3 0.3 7.3 0.3 7.3 0.3 4.3 0.3 4.3 0.3 4.3 0.3 2.8 0.3 4.0 max 4.0 0.3 2.4 2.4 2.4 1.3 1.3 1.3 0.10 0.10 0.10 0.10 0.10 0.10 0.13 0.13 0.13 3.8 3.8 3.8 3.5 3.5 3.5 3.5 3.5 3.5 T530 RATINGS & PART NUMBER REFERENCE Rated Rated CapaciCapaci-Case Case Code/ Voltage tance KEMET Part Number KEMET Part Number tance Size Case Size (V) F (F) 470 D/7343-31 T530D477M2R5A(1)E005 Current (Arms) ESR Ripple DC Maximum MSL DF% @ ESR m @ @ 100 kHz allowable DCLLeakageDF % 20Cm:@100 Reflow ripple current A @ 20C Temp 120 Hz w/'T= 20C VR20C max/ 120Hz kHz100 25C (mArms) kHz w/'T= 2C Max @ 100kHz* -55C to 260C Max 5min Max @ 125C 118 8.0 5.0 Rated Voltage (V) Rated Capacitance (F) Case Code/ Case Size KEMET Part Number 105C 7100 2.5 Volt Rating at 105C (1.7 Volt Rating at 125C) 220 D/7343-31 T530D227M006A(1)E005 D/7343-31 T530D477M2R5A(1)E006 118 8.0 6.0 6500 D T530D477M2R5A(1)E005 118A 8.0 5.0 7.1 2.3 220 D/7343-31 T530D227M006A(1)E006 D/7343-31 T530D477M2R5A(1)E010 118 10.0 10.0 5000 D T530D477M2R5A(1)E006 118A 8.0 6.0 6.5 2.1 330 D/7343-31 T530D337M006A(1)E006 D/7343-31 T530D567M2R5A(1)E005 140 8.0 5.0 7100 D T530D477M2R5A(1)E010 118A 10.0 10.0 5.0 1.6 330 D/7343-31 T530D337M006A(1)E010 Y/7343-40 T530Y687M2R5A(1)E005 170 8.0 5.0 7300 D T530D567M2R5A(1)E005 140A 8.0 5.0 7.1 2.3 330 Y/7343-40 T530Y337M006A(1)E005 Y/7343-40 T530Y687M2R5A(1)E006 170 8.0 6.0 6600 Y T530Y687M2R5A(1)E005 170A 8.0 5.0 7.2 2.3 330 Y/7343-40 T530Y337M006A(1)E006 D/7343-31 T530D687M2R5A(1)E006 170 8.0 6.0 6500 Y T530Y687M2R5A(1)E006 170A 8.0 6.0 6.6 2.1 330 Y/7343-40 T530Y337M006A(1)E010 6.3 3 T530D687M2R5A(1)E010170A 170 8.0 8.0 10.0 5000 D D/7343-31 T530D687M2R5A(1)E006 6.0 6.5 2.1 470 Y/7343-40 T530Y477M006A(1)E005 T530X687M2R5A(1)E006170A 170 8.0 8.0 6.0 6700 D X/7343-43 T530D687M2R5A(1)E010 10.0 5.0 1.6 470 X/7343-43 T530X477M006A(1)E004 T530Y108M2R5A(1)E005170A 250 8.0 8.0 5.0 7300 X Y/7343-40 T530X687M2R5A(1)E006 6.0 6.7 2.1 470 X/7343-43 T530X477M006A(1)E005 T530Y108M2R5A(1)E006250A 250 8.0 8.0 6.0 6600 Y Y/7343-40 T530Y108M2R5A(1)E005 5.0 7.2 2.3 470 X/7343-43 T530X477M006A(1)E006 X/7343-43 T530X108M2R5A(1)E004 250 8.0 4.0 8200 Y T530Y108M2R5A(1)E006 250A 8.0 6.0 6.6 2.1 470 X/7343-43 T530X477M006A(1)E010 X/7343-43 T530X108M2R5A(1)E005 250 8.0 5.0 7300 X T530X108M2R5A(1)E004 250A 8.0 4.0 8.2 2.6 680 X/7343-43 T530X687M006A(1)E010 T530X108M2R5A(1)E006250A 250 8.0 8.0 6.0 6700 X X/7343-43 T530X108M2R5A(1)E005 5.0 7.3 2.3 680 X/7343-43 T530X687M006A(1)E018 T530X158M2R5A(1)E005250A 375 8.0 8.0 5.0 7300 X X/7343-43 T530X108M2R5A(1)E006 6.0 6.7 2.1 150 D/7343-31 T530D157M010A(1)E005 T530D477M003A(1)E010375A 141 8.0 8.0 10.0 5000 X D/7343-31 T530X158M2R5A(1)E005 5.0 7.3 2.3 150 D/7343-31 T530D157M010A(1)E006 680 D/7343-31 T530D687M003A(1)E010 204Rating at 8.0125C)10.0 5000 3 Volt Rating at 105C (2 Volt 3 3 150 D/7343-31 T530D157M010A(1)E010 1000 D X/7343-43 T530X108M003A(1)E010141A 300 8.0 8.0 10.0 5200 470.0 T530D477M003A(1)E010 10.0 5.0 1.6 220 D/7343-31 T530D227M010A(1)E006 1500 D X/7343-43 T530X158M003A(1)E008204A 450 8.0 8.0 8.0 5800 680.0 T530D687M003A(1)E010 10.0 5.0 1.6 220 D/7343-31 T530D227M010A(1)E010 10 T530D337M004A(1)E005300A 132 8.0 8.0 5.0 7100 1000.0330 X D/7343-31 T530X108M003A(1)E010 10.0 5.2 1.6 220 Y/7343-40 T530Y227M010A(1)E006 1500.0330 X D/7343-31 T530X158M003A(1)E008 8.0 5.8 1.8 T530D337M004A(1)E006450A 132 8.0 8.0 6.0 6500 330 X/7343-43 T530X337M010A(1)E004 4T530D477M004A(1)E006 Volt Rating at 105C (2.7 Volt at 125C)6.0 470 D/7343-31 188 Rating8.0 6500 330 X/7343-43 T530X337M010A(1)E005 330.0470 D D/7343-31 T530D337M004A(1)E005 5.0 7.1 2.3 T530D477M004A(1)E010132A 188 8.0 8.0 10.0 5000 330 X/7343-43 T530X337M010A(1)E006 330.0470 D Y/7343-40 T530D337M004A(1)E006 6.0 6.5 2.1 T530Y477M004A(1)E005132A 188 8.0 8.0 5.0 7300 330 X/7343-43 T530X337M010A(1)E010 470.0470 D Y/7343-40 T530D477M004A(1)E006 6.0 6.5 2.1 T530Y477M004A(1)E006188A 188 8.0 8.0 6.0 6600 4 3 150 X/7343-43 T530X157M016A(1)E015 470.0680 D Y/7343-40 T530D477M004A(1)E010 10.0 5.0 1.6 T530Y687M004A(1)E005188A 272 8.0 8.0 5.0 7300 16 150 X/7343-43 T530X157M016A(1)E025 470.0680 Y X/7343-43 T530Y477M004A(1)E005 5.0 7.2 2.3 T530X687M004A(1)E004188A 272 8.0 8.0 4.0 8200 150 X/7343-43 T530X157M016A(1)E040 470.0680 Y X/7343-43 T530Y477M004A(1)E006 6.0 6.6 2.1 T530X687M004A(1)E005188A 272 8.0 8.0 5.0 7300 680.0680 Y X/7343-43 T530Y687M004A(1)E005 5.0 7.2 2.3 T530X687M004A(1)E006272A 272 8.0 8.0 6.0 6700 680.0680 X X/7343-43 T530X687M004A(1)E004 4.0 8.2 2.6 T530X687M004A(1)E010272A 272 8.0 8.0 10.0 5200 680.0 T530X687M004A(1)E005 5.0 7.3 2.3 1000 X X/7343-43 T530X108M004A(1)E006272A 400 8.0 8.0 6.0 6700 680.0 X T530X687M004A(1)E006 272A 8.0 6.0 6.7 2.1 (1) To680.0 complete part number, insert material10.0 designation ordering information on page 57. X KEMET T530X687M004A(1)E010 272Alead 8.0 5.2 from 1.6 1000.0 X ratings T530X108M004A(1)E006 400Aproduct 8.0 may 6.0 6.7 2.1 the same size at KEMET's Higher voltage and tighter tolerance be substituted within 470 470.0 470 470.0 560 470.0 680 560.0 680 680.0 680.0680 2.5 680.0680 680.0680 1000 680.0 1000 1000.0 1000 1000.0 1000 1000.0 1000 1000.0 1500 1000.0 1500.0470 DC Leakage A @ 20C max/ 5min DF% @ 20C 120 Hz Max ESR m @ 20C 100 kHz Max 139 8.0 5.0 7100 139 8.0 6.0 6500 208 8.0 6.0 6500 208 8.0 10.0 5000 208 8.0 5.0 7300 208 8.0 6.0 6600 208 8.0 10.0 5100 296 8.0 5.0 7300 296 8.0 4.0 8200 296 8.0 5.0 7300 296 8.0 6.0 6700 296 8.0 10.0 5200 428 8.0 10.0 5200 428 8.0 18.0 3900 150 8.0 5.0 7100 150 8.0 6.0 6500 150 8.0 10.0 5000 220 8.0 6.0 6500 220 8.0 10.0 5000 220 8.0 6.0 6600 330 8.0 4.0 8200 330 8.0 5.0 7300 330 8.0 6.0 6700 330 8.0 10.0 5200 240 8.0 15.0 4200 240 8.0 25.0 3300 240 8.0 40.0 2600 (1) ToVoltage completesubstitutions KEMET Part Number, insert lead material designation ordering information on page 57. Higher voltage ratings and tighter tolerance product option. will be marked with the higherfrom voltage ratings. may be substituted within the same size at KEMET's option. Voltage substitutions willl be marked with the higher voltage rating. (1) To complete KEMET Part Number, insert lead material designation from ordering information on page 56. Higher voltage ratings and tighter tolerance product may be substituted within the same size at KEMET'S option. Voltage substitutions will be marked with the higher voltage rating. 56 (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 Maximum allowable ripple current (mArms) 100kHz* MSL Reflow Temp 260C 3 3 3 *100kHz to 500kHz, 45 C CONDUCTIVE POLYMER CHIP CAPACITORS T530 SERIES - High Capacitance/Ultra-Low ESR T530 ORDERING INFORMATION T 530 X 158 M 003 A T Tantalum Series E008 ESR Expressed in Milliohms Lead Material 530 - Multiple Anode Polymer Case Size D, X, Y Capacitance Picofarad Code First two digits represent significant figures. Third digit specifies number of zeros. T = 100% Tin (Sn) Plated* (SnPb 5% Pb minimum) H =Tin/Lead Standard Solder Coated (SnPb 5% Pb minimum)for new design * S - Not recommended = Goldis not guaranteed with the `S' termination code. *Pb-freeG supply This termination code not available effective 15 July 2007. Failure Rate Conductive Polymer Surface Mount A = Not Applicable Capacitance Tolerance Voltage M = 20% Note: 006 = 6.3 COMPONENT MARKING (KM) KEMET High Capacitance/ Ultra-Low ESR Rated Voltage KM 158 3K 505 T530 SERIES CONSTRUCTION Polarity Indicator Picofarad Code KEMET ID PWC* "505" = The 5th week of 2005. T530X/T510E/T491E 1,000F Capacitance vs. Frequency T530X/T510E/T491E 1,000F Impedance & ESR vs. Frequency RECOMMENDED TEMPERATURE/VOLTAGE DERATING (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 57 TANTALUM AND ALUMINUM CHIP CAPACITORS Packaging Information Tape & Reel Packaging KEMET's Molded Tantalum and Aluminum Chip Capacitor families are packaged in 8 mm and 12 mm plastic tape on 7" and 13" reels, in accordance with EIA Standard 481-1: Taping of Surface Mount Components for Automatic Handling. This packaging system is compatible with all tape fed automatic pick and place systems. Right Hand Orientation Only (+) Embossed Carrier (-) Embossment 8mm .30 8mm (0.315") (.315or.012") or 12mm (0.472") 12mm .30 (.472 .012") Top Tape Thickness .10mm (.004") Max Thickness 178mm (7.00") 180mm (7.0") oror 330mm (13.00") 330mm (13.0") Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA-556. Case Code KEMET R I S T M U L W Z V A B C D Y X E EIA 2012-12 3216-10 3216-12 3528-12 3528-15 6032-15 6032-19 7343-15 7343-17 7343-20 3216-18 3528-21 6032-28 7343-31 7343-40 7343-43 7260-38 Tape Width-mm 7" Reel* 13" Reel 8 8 8 8 8 12 12 12 12 12 8 8 12 12 12 12 12 2,500 3,000 2,500 2,500 2,000 1,000 1,000 1,000 1,000 1,000 2,000 2,000 500 500 500 500 500 10,000 12,000 10,000 10,000 8,000 5,000 5,000 3,000 3,000 3,000 9,000 8,000 3,000 2,500 2,000 2,000 2,000 * No c-spec required for 7" reel packaging. C-7280 required for 13" reel packaging. * Standard reel packaging is not mandatory. * Bulk packaging also available using C-7610. 92 (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 Packaging QUANTITIES PACKAGED PER REEL TANTALUM, CERAMIC AND ALUMINUM CHIP CAPACITORS Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg Minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0.1 Newton to 1.0 Newton (10g to 100g) 12 mm 0.1 Newton to 1.3 Newton (10g to 130g) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 10 mm/minute. 3. Reel Sizes: Molded tantalum capacitors are available on either 180 mm (7") reels (standard) or 330 mm (13") reels (with C-7280). Note that 13" reels are preferred. 4. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA-556. Embossed Carrier Tape Configuration: Figure 1 Table 1 -- EMBOSSED TAPE DIMENSIONS (Metric will govern) Constant Dimensions -- Millimeters (Inches) Tape Size 8 mm and 12 mm D0 E 1.5 1.75 0.10 +0.10 -0.0 (0.059 (0.069 0.004) +0.004, -0.0) P0 P2 T Max T1 Max 4.0 0.10 2.0 0.05 0.600 0.100 (0.157 0.004) (0.079 0.002) (0.024) (0.004) Variable Dimensions -- Millimeters (Inches) Tape Size Pitch B1 Max. Note 1 D1 Min. Note 2 F P1 R Min. Note 3 T2 Max W 8 mm Single (4 mm) 4.4 1.0 3.5 0.05 4.0 0.10 25.0 2.5 8.0 0.30 (.315 0.012) 12 mm Double (8 mm) (0.173) (0.039) (0.138 0.002) (0.157 0.004) (0.984) (0.098) 8.2 (0.323) 1.5 5.5 0.05 (0.059) (0.217 0.002) 8.0 0.10 30.0 (0.315 0.004) (1.181) 4.6 12.0 0.30 (0.181) (0.472 0.012) A0B0K0 Note 4 NOTES 1. B1 dimension is a reference dimension for tape feeder clearance only. 2. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 3. Tape with components shall pass around radius "R" without damage (see sketch A). The minimum trailer length (Fig. 2) may require additional length to provide R min. for 12 mm embossed tape for reels with hub diameters approaching N min. (Table 2) 4. The cavity defined by A0, B0, and K0 shall be configured to surround the part with sufficient clearance such that the chip does not protrude beyond the sealing plane of the cover tape, the chip can be removed from the cavity in a vertical direction without mechanical restriction, rotation of the chip is limited to 20 degrees maximum in all 3 planes, and lateral movement of the chip is restricted to 0.5 mm maximum in the pocket (not applicable to vertical clearance.) 94 (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 TANTALUM, CERAMIC AND ALUMINUM CHIP CAPACITORS Packaging Information Embossed Carrier Tape Configuration (cont.) 20 Sketch D: Tape Camber (Top View) 1mm (0.039) Max. 1mm (0.039) Max. 250mm (9.843) Allowable camber to be 1 mm/250 mm. 400mm (15.75) Min. Figure 2: Tape Leader & Trailer Dimensions (Metric Dimensions Will Govern) Packaging Figure 3: Reel Dimensions (Metric Dimensions will govern) Table 2 - REEL DIMENSIONS (Metric will govern) Tape Size 8 mm A Max 330.0 (12.992) B* Min 1.5 (0.059) C 13.0 0.20 (0.512 0.008) D* Min 20.2 (0.795) 12 mm 330.0 (12.992) 1.5 (0.059) 13.0 0.20 (0.512 0.008) 20.2 (0.795) N Min 50.0 (1.969) See Note 3 Table 1 W1 8.4 +1.5, -0.0 (0.331 +0.059, -0.0) 12.4 +2.0, -0.0 (0.488 +0.078, -0.0) W2 Max 14.4 (0.567) 18.4 (0.724) (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 W3 7.9 Min (0.311) 10.9 Max (0.429) 11.9 Min (0.469) 15.4 Max (0.606) 95