VDE FLAT/VERTICAL TYPE HIGH POWER BIFURCATED CONTACT 38.1 1.500 25.4 1.000 25.4 1.000 10.9 .429 FEATURES 25.4 1.000 10.9 .429 4C Flat type 2C Flat type 11.2 .441 25.4 1.000 38.1 1.500 11.2 .441 * Space saver -- Flat series and vertical series * High contact reliability due to bifurcated contacts -- 2C: 5 A 250 V AC, 4C: 5 A 125 V AC, 4 A 250 V AC * Latching types available * Low operating power -- 2C: 200 mW, 4C: 400 mW (Single side stable) * Soldering flux inflow prevented by terminal location * Amber sealed types available * High breakdown voltage for transient protection -- 1,000 Vrms between open contacts, contact sets 27.8 1.094 27.8 1.094 4.1 .161 4.1 .161 4C Vertical type (PC board) NC-RELAYS 2C Vertical type (PC board) mm inch SPECIFICATIONS Characteristics (at 25C 77F 50% Relative humidity) Contacts Types Standard Amber sealed Arrangement 2 Form C, 4 Form C Initial contact resistance, max. 50 m (By voltage drop 6 V DC 1 A) Max. switching 2C: 1,250 VA 150 W 2C: 750 VA 150 W power 4C: 1,000 VA 150 W 4C: 500 VA 150 W Max. switching 250 V AC voltage Rating Max. switching (resistive 5A current load) Max. switching 5A carrying current Min. switching 100 A 1 V DC power 105 at 105 at 5 A 250 V AC 3 A 250 V AC 2C 5x105 at 5x105 at 5 A 30 V DC 5 A 30 V DC Expected life (minimum) 105 at 105 at 4 A 250 V AC 2 A 250 V AC 4C 5x105 at 5x105 at 5 A 30 V DC 5 A 30 V DC Contact material Gold-clad silver nickel Coil (Polarized) (at 25C 77F) Minimum operating power 2 C single side stable 4 C single side stable 2 C single side stable Nominal operating power 4 C single side stable Minimum set and 2 C 2 coil latching reset power 4 C 2 coil latching Nominal set and 2 C 2 coil latching reset power 4 C 2 coil latching Up to 48 V DC 110 V DC Approx. 200 mW 500 mW Approx. 400 mW 500 mW Approx. 360 mW 900 mW Approx. 720 mW 900 mW Approx. 450 mW Approx. 900 mW Approx. 800 mW Approx. 1,600 mW Max. operating speed Initial insulation resistance Between open contacts, Initial contact sets breakdown Between contacts and 1 voltage* coil Operate time (at nominal voltage) Release time (at nominal voltage) Operate time (latching) (at nominal voltage) Reset time (latching) (at nominal voltage) Temperature rise (at nominal voltage) Functional*2 Shock resistance Destructive*3 Vibration resistance Conditions for operation, transport and storage*5 (Not freezing and condensing at low temperature) Unit weight Functional*4 Destructive (Single side stable) 2C 4C (2 coil latching) Humidity 180 cpm Min. 100 M at 500 V DC 1,000 Vrms 2,000 Vrms Approx. 6 ms Approx. 3 ms Approx. 6 ms Approx. 6 ms Max. 65C Min. 98 m/s2 {10 G} Min. 980 m/s2 {100 G} 58.8 m/s2 {6 G}, 10 to 55 Hz at double amplitude of 1 mm 117.6 m/s2 {12 G}, 10 to 55 Hz at double amplitude of 2 mm up to 48 V DC: -40C to +70C -40F to +158F 110 V DC: -40C to +55C -40F to +131F -40C to +55C -40F to +131F -40C to +55C -40F to +131F 5 to 85% R.H. 2C/Approx. 16 g .56 oz 4C/Approx. 18 g .63 oz Remarks * Specifications will vary with foreign standards certification ratings. *1 Detection current: 10 mA *2 Half-wave pulse of sine wave: 11ms; detection time: 10s *3 Half-wave pulse of sine wave: 6ms *4 Detection time: 10s *5 Refer to 5. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT (Page 61). 223 NC TYPICAL APPLICATIONS Use NC Relays for power control up to 5 A or -- Tape recorders, temperature controls, video tape recorders Telecommunications equipment, measuring controls, copiers Date processing equipment, computer peripherals Automatic vendors, copiers, automatic storage controls, N.C. machines ORDERING INFORMATION Ex. NC 2 EB J D Housing Contact arrangement Type classification 2: 2 Form C 4: 4 Form C Nil: Standard type EB: Amber sealed type Nil: Vertical series J: Flat series P DC 12V L2 Operating function Mounting method Nil: Plug-in P: PC board termial Nil: Single side stable L2: 2 coil latching Coil voltage DC 5, 6, 12, 24, 48, 110 V (Notes) 1. Flat series are available in PC board terminal types only. 2. For VDE recognized type, add suffix VDE. 3. Standard packing Carton: 20 pcs. Case: 200 pcs. 4. UL/CSA, approved type is standard. TYPE AND COIL DATA (at 20C 68F) (Coil data for Amber sealed types are same as those for standard types.) 2 Form C Single side stable Flat series Vertical series PC board terminal NC2D-JP-DC5V NC2D-JP-DC6V NC2D-JP-DC12V NC2D-JP-DC24V NC2D-JP-DC48V NC2D-JP-DC110V Plug-in PC board terminal NC2D-DC5V NC2D-DC6V NC2D-DC12V NC2D-DC24V NC2D-DC48V NC2D-DC110V NC2D-P-DC5V NC2D-P-DC6V NC2D-P-DC12V NC2D-P-DC24V NC2D-P-DC48V NC2D-P-DC110V Pick-up voltage (max.) 4.0 4.8 9.6 19.2 38.4 88.0 Coil voltage, V DC Drop-out Maximum voltage allowable (min.) voltage 0.5 6.75 0.6 8.1 1.2 16.2 2.4 32.4 4.8 64.8 11.0 121 Coil resistance, (10%) Nominal operating power, mW 69.4 100 400 1,600 6,400 13,500 900 Coil resistance, (10%) Nominal operating power, mW 31.3 45.0 180 720 2,880 15,125 800 Coil resistance, (10%) Nominal operating power, mW 360 2 Form C 2 coil latching Flat series PC board terminal NC2D-JPL2-DC5V NC2D-JPL2-DC6V NC2D-JPL2-DC12V NC2D-JPL2-DC24V NC2D-JPL2-DC48V NC2D-JPL2-DC110V Vertical series Plug-in PC board terminal NC2D-L2-DC5V NC2D-L2-DC6V NC2D-L2-DC12V NC2D-L2-DC24V NC2D-L2-DC48V NC2D-L2-DC110V NC2D-PL2-DC5V NC2D-PL2-DC6V NC2D-PL2-DC12V NC2D-PL2-DC24V NC2D-PL2-DC48V NC2D-PL2-DC110V Coil voltage, V DC Pick-up voltage (max.) 4.0 4.8 9.6 19.2 38.4 88.0 Reset voltage (max.) 4.0 4.8 9.6 19.2 38.4 88.0 Maximum allowable voltage 5.5 6.6 13.2 26.4 52.8 121 4 Form C Single side stable Flat series PC board terminal NC4D-JP-DC5V NC4D-JP-DC6V NC4D-JP-DC12V NC4D-JP-DC24V NC4D-JP-DC48V NC4D-JP-DC110V 224 Vertical series Plug-in NC4D-DC5V NC4D-DC6V NC4D-DC12V NC4D-DC24V NC4D-DC48V NC4D-DC110V PC board terminal NC4D-P-DC5V NC4D-P-DC6V NC4D-P-DC12V NC4D-P-DC24V NC4D-P-DC48V NC4D-P-DC110V Pick-up voltage (max.) 4.0 4.8 9.6 19.2 38.4 88.0 Coil voltage, V DC Drop-out Maximum voltage allowable (min.) voltage 0.5 5.5 0.6 6.6 1.2 13.2 2.4 26.4 4.8 52.8 11.0 121 34.7 50 200 800 3,200 13,500 720 900 NC 4 Form C 2 coil latching Flat series Vertical series PC board terminal NC4D-JPL2-DC5V NC4D-JPL2-DC6V NC4D-JPL2-DC12V NC4D-JPL2-DC24V NC4D-JPL2-DC48V NC4D-JPL2-DC110V Notes: Plug-in NC4D-L2-DC5V NC4D-L2-DC6V NC4D-L2-DC12V NC4D-L2-DC24V NC4D-L2-DC48V NC4D-L2-DC110V Coil voltage, V DC Maximum Pick-up Reset allowable voltage voltage voltage (max.) (max.) (within 2 min.) PC board terminal NC4D-PL2-DC5V NC4D-PL2-DC6V NC4D-PL2-DC12V NC4D-PL2-DC24V NC4D-PL2-DC48V NC4D-PL2-DC110V 4.0 4.8 9.6 19.2 38.4 88.0 1. Two coil latching relay 4C series are for intermittent operation only. Power should be applied to coil continuously for no more than two minutes. 2. Coil resistance is the measured value at a coil temperature of 20C. Compensate coil resistance by plus or minus 0.4% for each degree (C) of coil temperature change. 4.0 4.8 9.6 19.2 38.4 88.0 5.5 6.6 13.2 26.4 52.8 121 Coil resistance, (10%) Nominal operating power, mW 15.6 22.5 90 360 1,440 7,560 1,600 3. "Maximum allowable voltage" is that value at maximum contact rating and maximum ambient temperature. The graph shown in the data describes the inter-relationship; care should be taken to prevent the total of ambient temperature and the coil temperature rise from exceeding 120C. DIMENSIONS mm inch Flat series 2C single side stable (NC2D-JP) Standard type Amber sealed type 5.08 5.08 5.08 .200 .200 .200 PC board pattern (Copper-side view) 8-1.2 DIA. HOLES 8-.047 DIA. HOLES 5.08 5.08 5.08 .200 .200 .200 11 12 13 14 7 5 27.94 1.100 27.94 1.100 25.4 1.000 (NC2ED-JP) 25.4 1.000 27.94 1.100 2.54 .100 25.4 1.000 10.9 .429 3.5 .138 25.4 1.000 10.9 .429 4 2 2.54 .100 Tolerance: 0.1 .004 3.5 .138 Schematic (Top view) 7.62 5.08 7.62 .300 .200 .300 14 13 12 11 7.62 5.08 7.62 .300 .200 .300 General tolerance: 0.5 .020 2 4 5 - + 7 Deenergized position 2C 2 coil latching (NC2D-JPL2) Standard type Amber sealed type PC board pattern (Copper-side view) 10-1.2 DIA. HOLES 10-.047 DIA. HOLES 5.08 5.08 5.08 .200 .200 .200 5.08 5.08 5.08 .200 .200 .200 11 12 13 14 27.94 1.100 27.94 1.100 25.4 1.000 (NC2ED-JPL2) 27.94 1.100 25.4 1.000 7 2.54 .100 2.54 .100 25.4 1.000 10.9 .429 3.5 .138 25.4 1.000 10.9 .429 3.5 .138 5 4 2 0.5 .020 Tolerance: 0.1 .004 Schematic (Top view) 5.08 5.08 5.08 .200 2.54 .200 2.54 .200 .100 .100 5.08 5.08 5.08 .200 2.54 .200 2.54 .200 .100 .100 General tolerance: 0.5 .020 14 13 12 11 2 34 54 7 -- ++ Diagram shows the "reset" position when terminals 3 and 6 are energized. Energize terminals 4 and 5 to transfer contacts. 225 NC 4C single side stable (NC4D-JP) mm inch Standard type Amber sealed type 5.08 5.08 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 .200 .200 PC board pattern (Copper-side view) 14-1.2 DIA. HOLES 14-.047 DIA. HOLES 5.08 5.08 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 .200 .200 9 10 11 12 13 14 15 16 27.94 1.100 (NC4ED-JP) 27.94 1.100 25.4 1.000 25.4 1.000 27.94 1.100 8 2.54 .100 38.1 1.500 10.9 .429 3.5 .138 38.1 1.500 10.9 .429 7 5 4 2 1 2.54 .100 Tolerance: 0.1 .004 3.5 .138 Schematic (Top view) 16 15 14 13 12 11 10 9 5.08 7.62 5.08 7.62 5.08 .200 .300 .200 .300 .200 5.08 7.62 5.08 7.62 5.08 .200 .300 .200 .300 .200 1 2 General tolerance: 0.5 .020 4 5 7 8 - + Deenergized position 4C 2 coil latching (NC4D-JPL2) Standard type Amber sealed type 5.08 5.08 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 .200 .200 PC board pattern (Copper-side view) 16-1.2 DIA. HOLES 16-.047 DIA. HOLES 5.08 5.08 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 .200 .200 9 10 11 12 13 14 15 16 27.94 1.100 (NC4ED-JPL2) 25.4 1.000 27.94 1.100 25.4 1.000 27.94 1.100 2.54 .100 10.9 .429 38.1 1.500 3.5 .138 38.1 1.500 10.9 .429 8 7 2.54 .100 3.5 .138 6 5 4 3 2 1 0.5 .020 Tolerance: 0.1 .004 Schematic (Top view) 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 2.54 2.54 .100 .100 16 15 14 13 12 11 10 9 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 2.54 2.54 .100 .100 1 2 34 56 7 8 -- ++ General tolerance: 0.5 .020 Diagram shows the "reset" position when terminals 3 and 6 are energized. Energize terminals 4 and 5 to transfer contacts. Slim series PC board series 2C single side stable (NC2D-P) Standard type Amber sealed type PC board pattern (Copper-side view) 8-1.2 DIA. HOLES 8-.047 DIA. HOLES 11 7.62 .300 27.8 1.094 27.8 1.094 7 2.54 .100 4.1 .161 4.1 .161 25.4 1.000 (NC2ED-PL2) 7.62 .300 11.2 .441 5.08 5.08 5.08 .200 .200 .200 11 7 12 6 5 13 25.4 1.000 5.08 5.08 5.08 .200 .200 .200 7.62 5.08 7.62 .300 .200 .300 4 2 Tolerance: 0.1 .004 .300 Schematic (Bottom view) 2 7.62 5.08 7.62 .300 .200 .300 General tolerance: 0.5 .020 226 7.62 11.2 .441 5 2.54 .100 11 12 13 14 14 4 3 12 13 14 7 5 4 + - 2 Deenergized position NC 2C 2 coil latching (NC2D-PL2) mm inch Standard type Amber sealed type PC board pattern (Copper-side view) 10-1.2 DIA. HOLES 10-.047 DIA. HOLES 11 27.8 1.094 27.8 1.094 7.62 .300 7 7.62 .300 11.2 .441 25.4 1.000 5.08 5.08 5.08 .200 .200 .200 11 7 12 13 6 5 4.1 .161 25.4 1.000 5.08 5.08 5.08 .200 .200 .200 7.62 11.2 .441 2 Schematic (Bottom view) 11 12 13 14 2 5.08 5.08 5.08 .200 2.54 .200 2.54 .200 .100 .100 7.62 5.08 5.08 .300 .200 2.54.200 .100 7 6 5 4 3 2 ++ -- General tolerance: 0.5 .020 4C single side stable (NC4D-P) 43 Tolerance: 0.1 .004 .300 14 4 3 6 5 2.54 .100 2.54 0.5 .100 .020 4.1 .161 (NC2ED-P) 12 13 14 Standard type Diagram shows the "reset" position when terminals 3 and 6 are energized. Energize terminals 4 and 5 to transfer contacts. Amber sealed type PC board pattern (Copper-side view) 14-1.2 DIA. HOLES 14-.047 DIA. HOLES 38.9 1.520 38.1 1.500 9 10 11 12 13 14 15 16 7.62 .300 8 2.54 .100 27.8 1.094 27.8 1.094 7 2.54 .100 5 4 2 1 Tolerance: 0.1 .004 (NC4ED-P) 4.1 .161 4.1 .161 7.62 .300 11.2 .441 38.1 1.500 5.08 5.08 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 .200 .200 9 10 8 11 12 7 13 6 5 Schematic (Bottom view) 7.62 11.2 .441 5.08 5.08 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 .200 .200 .300 9 10 11 12 13 14 15 16 14 15 16 4 3 2 8 7 1 5.08 7.62 5.08 7.62 5.08 .200 .300 .200 .300 .200 5.08 7.62 5.08 7.62 5.08 .200 .300 .200 .300 .200 5 4 2 1 + - Deenergized position General tolerance: 0.5 .020 4C 2 coil latching (NC4D-PL2) Standard type Amber sealed type PC board pattern (Copper-side view) 16-1.2 DIA. HOLES 16-.047 DIA. HOLES 38.9 1.520 38.1 1.500 9 10 11 12 13 14 15 16 7.62 .300 27.8 1.094 27.8 1.094 2.54 .100 8 7 2.54 .100 6 5 4 3 2 1 0.5 .020 Tolerance: 0.1 .004 4.1 .161 (NC4ED-PL2) 38.1 1.500 5.08 5.08 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 .200 .200 9 10 8 11 12 7 6 5 13 4 3 4.1 .161 7.62 .300 11.2 .441 5.08 5.08 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 .200 .200 7.62 .300 11.2 .441 Schematic (Bottom view) 9 10 11 12 13 14 15 16 14 15 16 2 1 5.085.08 5.08 5.08 5.08 .200.200 2.54 .2002.54.200 .200 .100 .100 8 7 65 43 2 1 5.085.08 5.08 5.08 5.08 .200.200 2.54 .2002.54.200 .200 .100 .100 General tolerance: 0.5 .020 ++-- Diagram shows the "reset" position when terminals 3 and 6 are energized. Energize terminals 4 and 5 to transfer contacts. 227 NC Slim series Plug-in series 2C single side stable (NC2D) mm inch Standard type Amber sealed type Schematic (Bottom view) 11 12 13 14 27.8 1.094 27.8 1.094 6.1 .240 6.1 .240 (NC2ED) 7.62 .300 11.2 .441 25.4 1.000 5.08 5.08 5.08 .200 .200 .200 11 7 12 25.4 1.000 5.08 5.08 5.08 .200 .200 .200 7 5 4 2 + - Deenergized position 7.62 .300 11.2 .441 13 14 6 5 4 3 2 7.62 5.08 7.62 .300 .200 .300 7.62 5.08 7.62 .300 .200 .300 General tolerance: 0.5 .020 2C 2 coil latching (NC2D-L2) Standard type Amber sealed type Schematic (Bottom view) 11 12 13 14 27.8 1.094 27.8 1.094 7 6 5 4 3 2 ++ -- 6.1 .240 6.1 .240 7.62 .300 11.2 .441 25.4 1.000 (NC2ED-L2) 5.08 5.08 5.08 .200 .200 .200 11 7 12 7.62 .300 11.2 .441 25.4 1.000 5.08 5.08 5.08 .200 .200 .200 Diagram shows the "reset" position when terminals 3 and 6 are energized. Energize terminals 4 and 5 to transfer contacts. 13 14 6 5 4 3 2 5.08 5.08 5.08 .200 2.54 .2002.54.200 .100 .100 5.08 5.08 5.08 .200 2.54 .2002.54.200 .100 .100 General tolerance: 0.5 .020 4C single side stable (NC4D) Standard type Amber sealed type Schematic (Bottom view) 9 10 11 12 13 14 15 16 38.9 1.520 38.1 1.500 8 7 27.8 1.094 27.8 1.094 6.1 .240 (NC4ED-L2) 5.08 5.08 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 .200 .200 9 10 11 8 7 12 6 5 13 14 4 3 2 1 Deenergized position 6.1 .240 7.62 .300 11.2 .441 38.1 1.500 5 4 + - 7.62 .300 11.2 .441 5.08 5.08 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 .200 .200 15 16 2 1 5.08 7.62 5.08 7.62 5.08 .200 .300 .200 .300 .200 5.08 7.62 5.08 7.62 5.08 .200 .300 .200 .300 .200 General tolerance: 0.5 .020 4C 2 coil latching (NC4D-L2) Standard type Amber sealed type Schematic (Bottom view) 9 10 11 12 13 14 15 16 38.9 1.520 38.1 1.500 8 7 65 43 2 1 -- ++ 27.8 1.094 27.8 1.094 6.1 .240 (NC4ED-L2) 38.1 1.500 5.08 5.08 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 .200 .200 9 10 11 8 7 12 6 5 13 14 4 3 6.1 .240 7.62 .300 11.2 .441 5.08 5.08 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 .200 .200 15 16 2 1 5.085.08 5.08 5.08 5.08 .200.200 2.54 .2002.54.200 .200 .100 .100 5.085.08 5.08 5.08 5.08 .200.200 2.54 .2002.54.200 .200 .100 .100 General tolerance: 0.5 .020 228 Diagram shows the "reset" position when terminals 3 and 6 are energized. Energize terminals 4 and 5 to transfer contacts. 7.62 .300 11.2 .441 NC Schematic -- Energize relays only in the polarities shown -- 1. Single side stable Same operation as conventional magnetic relays. Contacts will transfer only when coil is energized under indicated polarity. 2C deenergized coil energized coil 4C 2. 2 coil latching Contacts will transfer only when coil is energized under indicated polarity. Once transferred, contacts remain in that position even with power off until opposite coil is energized at indicated polarity. 2C 4C 2C Reset 4C Reset set set Diagrams show the "set" position when terminals 4 (-) and 5 (+) are energized. When the coil current is switched off, these contacts remain in "make" position. Reset Reset set set Energize terminals 3 (-) and 6 (+) to transfer the contacts. Diagrams show the "reset" position when terminals 3 (-) and 6 (+) are energized. Energize terminals 4 (-) and 5 (+) to transfer the contacts. AC load (2C) AC load (4C) REFERENCE DATA Standard type 1.-(1) Life curve DC load (2C, 4C) 5,000 10,000 5,000 1,000 100 220 V DC resistive 1,000 250 V AC resistive 250 V AC inductive (pf=0.4) 100 Expected life, x104 Expected life, x104 Expected life, x104 110 V DC resistive 1,000 125 V AC resistive 250 V AC resistive 125 V AC inductive (pf=0.4) 250 V AC inductive (pf=0.4) 100 30 V DC resistive 10 10 0.1 1.0 0 10 1 Contact carrying current, A 2 3 4 0 5 Contact carrying current, A 2.-(2) Temperature rise characteristics for 2 coil latching Measured portion: Inside the coil Measured portion: Inside the coil ing 70 rr cu c nta o 5A 40 rre cu (C 3 4C 2C 20 0.6 0.8 1.0 1.2 1.4 1.6 1.8W 100 120 140 160 180 200 4 5 70 60 0 A (No. contact carring current) 50 5 A (Max. contact carring current) 40 30 0 A (No. contact carring current) 20 0.4 3 5 A (Max. contact carring current) t) ren ur gc ta rin on arr car (C act 3 A (Cont nt) urre 5A gc rrin a c act ont A (C 30 Operating power Coil voltage up to (2C : 48 V DC ) : 100 V DC (2C 4C : all types ) ct ing rr ca tc 60 50 t) en 80 2 Contact carrying current, A nt) Temperature rise, C Temperature rise, C 2.-(1) Temperature rise characteristics for single side stable 1 4C 2C 10 220%V 100 110 120 130 140 150%V 0 5 10 15 20 25 Energizing time, min. 229 NC 3. Operate time for single side stable 20 4. Release time for single side stable 5 4c 2c 18 4 14 12 10 8 6 Max. Max. 4 Min. Min. Release time, ms 16 Operate time, ms 4c 2c 3 Max. 2 Min. Max. Min. 1 2 80 100 90 110 Coil applied voltage,%V 80 100 90 110 Coil applied voltage,%V 120 120 110 110 100 Rated of change, % Rated of change, % 5. Rate of change of pick-up and drop-out voltage 2 Form C single side stable 4 Form C single side stable Pick-up voltage 90 100 Pick-up voltage 90 Drop-out voltage 80 80 Drop-out voltage -40 -20 -40 -20 0 20 40 60 80 Ambient temperature, C 0 20 40 60 80 Ambient temperature, C Sample: NC2D-P-DC24 V (2c slim single side stable) Sample: NC2D-P-DC110 V (2c slim single side stable), NC4D-P-DC24 V (4c slim single side stable) 0A 250 3A 5A 200 (C on tac (C tc on tac (C arr ing tc on tac arr tc ing arr ing cu rre nt) cu rre nt) cu rre nt) 150 250 200 0A 3A 150 (Co nta (Co ct c nta 5A arrin (Co ct c g cu rren ntac arrin t) g cu rren t ca rring t) curr ent) 100 100 40 50 60 70 Ambient temperature, C 230 Max. continuous voltage, %V 6.-(2) Ambient temperature vs Max. continuous voltage Max. continuous voltage, %V 6.-(1) Ambient temperature vs Max. continuous voltage 30 40 50 Ambient temperature, C NC ACCESSORIES NC2 Flat NC4 Flat Sockets incorporate a spring clip at each end permitting single "snap-in" attachment to chassis or panels - no screws NC2 Slim NC4 Slim necessary. Relays are held firmly in the socket by clips integrally molded into the socket. TYPES For Flat series Part No. NC2-JPS NC4-JPS NC2-JPL2S NC4-JPL2S For Slim series Terminals P/C board P/C board P/C board P/C board Mating relay NC2D-JP NC4D-JP NC2D-JPL2 NC4D-JPL2 Standard packing: Carton: 20 pieces Case: 200 pieces Part No. NC2-PS NC4-PS NC2-SS NC4-SS NC2-L2PS NC4-L2PS NC4-L2SS NC4-L2SS Terminals P/C board P/C board Solder Solder P/C board P/C board Solder Solder Mating relay NC2D-P NC4D-P NC2D NC2D NC4D-PL2 NC2D-PL2 NC2D-L2 NC4D-L2 SPECIFICATIONS Maximum continuous current Initial breakdown voltage Initial insulation resistance Heat resistance Flat series: 5 A 250 V AC Slim series: 5 A 250 V AC 2,000 V AC (Except for coil-coil of L2 types: 1,500 V AC) 100 M at 500 V DC 150C (302F) for one hour Caution: Do not insert or remove relays while in the energized condition. 231 NC DIMENSIONS Flat series NC2-JPS NC2-JPL2S mm inch Terminal width: 0.9 .035 Terminal thickness: 0.4 .016 10.16 .400 PC board pattern (copper-side view) Terminal portion 15.24 .600 5.08 .200 2-3.5 DIA. HOLES 2-.138 DIA. HOLES 3.9 .154 0.1 MAX. .004 11 12 13 14 11 12 13 14 34.9 1.374 27.94 1.100 44.3 27.94 1.744 1.100 10-1.2 DIA. HOLES 10-.047 DIA. HOLES 7 6 5 4 3 2 7 14.8 .582 25.4 1.000 65 4 3 2 0.5 .020 2.54 .100 2.54 .100 5.08.200 10.16 .400 20.32 .800 Terminals 3 and 6 excluded for NC2-JPS. General tolerance: 0.5 .020 NC4-JPS NC4-JPL2S 35.56 1.400 25.4 1.000 15.24 .600 5.08.200 9 10 11 12 13 14 15 16 27.94 1.100 16-1.2 DIA. HOLES 16-.047 DIA. HOLES 44.3 27.94 1.744 1.100 8 40 1.575 3.9 .154 0.1 MAX. .004 9 10 11 12 13 14 15 16 2-3.5 DIA. HOLES 2-.138 DIA. HOLES 34.9 1.374 PC board pattern (copper-side view) Terminal portion Terminal width: 0.9 .035 Terminal thickness: 0.4 .016 20.32 .800 Tolerance: 0.1 .004 14.8 .582 7 6 5 4 3 2 1 5.08.200 10.16 .400 20.32.800 30.48 1.200 8 7 6 5 43 2.54 .100 2.54 .100 0.5 .020 2 1 Terminals 3 and 6 excluded for NC4-JPS. General tolerance: 0.5 .020 Slim series NC2-SS NC2-L2S Tolerance: 0.1 .004 Terminal width: 1.9 .075 Terminal thickness: 0.4 .016 12.6 .496 27.9 10.16 5.08 1.100 20.32 .400 .200 .800 29.9 1.177 Chassis cutout 11.2 .441 8.6 8.0 20.4 .339 .315 .803 3.9 1.0 .154 .039 28.4 1.118 15.24 5.08 .660 .200 11.5 .453 Chassis thickness range: 1.0 to 2.0 .039 to .079 7.62 .300 Terminals 3 and 6 excluded for NC2-SS. General tolerance: 0.5 .020 NC2-PS NC2-L2P Terminal width: 0.9 .035 Terminal thickness: 0.4 .016 12.6 .496 29.9 1.177 4.6 20.4 8.6 .181 .803 .339 3.9 1.0 .154 .039 PC board pattern (copper-side view) 11.2 .441 11 12 13 14 27.9 1.100 10.16 20.32 .400 5.08 .200 .800 15.24 5.08 .660 .200 7.62 .300 10-1.2 DIA. HOLES 10-.047 DIA. HOLES 7 2.54 .100 2.54 .100 6 5 43 0.5 .020 2 7.62 .300 Terminals 3 and 6 excluded for NC2-PS. General tolerance: 0.5 .020 232 Tolerance: 0.1 .004 NC NC4-SS NC4-L2S Terminal width: 1.9 .075 Terminal thickness: 0.4 .016 Chassis cutout 11.2 .441 12.6 .496 20.4 8.6 8.0 .803 .339 .315 3.9 1.0 .154 .039 42.5 1.673 35.56 15.24 1.400 5.08 .600 25.4 42.0 1.000 1.654 .200 30.48 1.200 10.165.08 20.32 .400 .200 .800 44.0 1.732 11.5 .453 7.62 .300 Chassis thickness range: 1.0 to 2.0 .039 to .079 Terminals 3 and 6 excluded for NC4-SS. General tolerance: 0.5 .020 NC4-PS NC4-L2P Terminal width: 0.9 .035 Terminal thickness: 0.4 .016 12.6 .496 11.2 .441 4.6 8.6 .181 20.4 .339 .803 3.9 1.0 .154 .039 PC board pattern (copper-side view) 9 10 11 12 13 14 15 16 44.0 1.732 42.0 1.654 20.32 .800 10.16 5.08 30.48 .400.200 1.200 15.24 35.56 5.08 .600 25.4 1.400 1.000 .200 16-1.2 DIA. HOLES 16-.047 DIA. HOLES 7.62 .300 2.54 .100 8 7 6 5 43 2 1 2.54 .100 0.5 .020 7.62 .300 Terminals 3 and 6 excluded for NC4-PS. General tolerance: 0.5 .020 Tolerance: 0.1 .004 NOTES 1. To maintain insulation between coils of 2 coil latching series, terminals 5 and 6 for flat series, and terminals 3 and 4 for slim series should be connected to provide common return. 5 Set coil 4 Set switch (2) "Bottom View" wiring diagram is indicated for the Slim series because terminals can not be seen from above. 6 Reset coil 5. Sockets (1) When PC board series are used with socket, do not apply loads exceeding 3 A. (2) Soldering should be done quickly to avoid damaging the thermoplastic body. (3) Insulation will be optimum when wire connections are soldered as shown with all slim sockets. 3 Reset switch 2. 2 coil latching series 4C are for intermittent operation only. Power should be applied to coils continuously for no more than two minutes. 3. When designing printed circuit board patterns, note that: (1) "Top View" wiring diagram is indicated for the Flat series because terminals can be seen from above. 4. When using slim series in close proximity, mount all relays facing the same direction. Different mounting directions may cause change in the relay characteristics because NC relays are polarized. Same direction For Cautions for Use, see Relay Technical Information (Page 48 to 76). 9/1/2000 All Rights Reserved, (c) Copyright Matsushita Electric Works, 233 Ltd. Go To Online Catalog