DATASHEET LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER Description Features The ICS670-01 is a high-speed, low phase noise, Zero Delay Buffer (ZDB) which integrates IDT's proprietary analog/digital Phase Locked Loop (PLL) techniques. The zero delay feature means that the rising edge of the input clock aligns with the rising edges of the outputs. There are two identical outputs on the chip. FBCLK should be connected to FBIN. Each output has its own output enable pin. * * * * * * * * * * * The ICS670-01 is ideal for synchronizing outputs in a large variety of systems, from personal computers to data communications to video. By allowing off-chip feedback paths, the ICS670-01 can eliminate the delay through other devices. The 15 different on-chip multipliers work in a variety of applications. Arbitrary multiplication factors (including fractions) can be configured on the ICS527. * * * ICS670-01 Packaged in 16-pin SOIC Pb (lead) free package, RoHS compliant Clock inputs from 5 to 160 MHz (see page 2) Patented PLL with low phase noise Output clocks up to 160 MHz at 3.3 V 15 selectable on-chip multipliers Power down mode available Low phase noise: -124 dBc/Hz at 10 kHz Output enable function tri-states outputs Low jitter-15 ps one sigma Full swing CMOS outputs with 25 mA drive capability at TTL levels Advanced, low power, sub-micron CMOS process Industrial temperature version available Operating voltage of 3.3 V or 5 V Block Diagram VDD OE1 3 ICLK Phase Detector, Charge Pump, and Loop Filter FBIN S3:S0 Voltage Controlled Oscillator ROMBased Multipliers FBCLK CLK2 4 3 GND OE2 External Feedback from FBCLK is recommended. IDT(R) LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER 1 ICS670-01 REV L 012315 ICS670-01 LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER Pin Assignment ZDB AND MULTIPLIER Multiplier Select Table S3 S2 S1 S0 CLK2 (and FBCLK) Input Range (MHz) 0 0 0 0 Low (Power down entire chip) - GND 0 0 0 1 Input x1.333 18 - 120 0 1 0 Input x6 5 - 26.67 VDD 1 16 GND VDD 2 15 GND VDD 3 14 CLK2 4 13 S0 0 OE2 5 12 S1 0 0 1 1 Input x1.5 16.67 - 107 1 0 0 Input x3.333 7.5 - 48 FBCLK 6 11 S2 0 OE1 7 10 S3 0 1 0 1 Input x2.50 10 - 64 ICLK 0 1 1 0 Input x4 6 - 40 0 1 1 1 Input x1 25 - 160 1 0 0 0 Input x2.333 11 - 69 1 0 0 1 Input x2.666 10 - 60 1 0 1 0 Input x12 5 - 13.33 1 0 1 1 Input x3 8 - 53.33 1 1 0 0 Input x10 5 - 16 1 1 0 1 Input x5 6 - 32 1 1 1 0 Input x8 5 - 20 1 1 1 1 Input x2 12 - 80 9 8 FBIN Pin Descriptions Pin Number Pin Name Pin Type Pin Description 1-3 VDD Input Power supply. Connect all pins to the same voltage (either 3.3 V or 5 V). Pins 1 and 2 supply the analog sections of the chip. 4 CLK2 5 OE2 6 FBCLK 7 OE1 Input Output clock enable 1. Tri-states the feedback clock output when low. 8 FBIN Input Feedback clock input. 9 ICLK Input Clock input. Connect to a 5 - 210 MHz clock. 10 S3 Input Multiplier select pin 3. Determines outputs per table above. Internal pull-up. 11 S2 Input Multiplier select pin 2. Determines outputs per table above. Internal pull-up. 12 S1 Input Multiplier select pin 1. Determines outputs per table above. Internal pull-up. 13 S0 Input Multiplier select pin 0. Determines outputs per table above. Internal pull-up. 14 - 16 GND Power Connect to ground. Output Clock output from VCO. Output frequency equals the input frequency times multiplier. Input Output clock enable 2. Tri-states the clock 2 output when low. Output Clock output from VCO. Output frequency equals the input frequency times multiplier. IDT(R) LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER 2 ICS670-01 REV L 012315 ICS670-01 LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER ZDB AND MULTIPLIER External Components The ICS670-01 requires a minimum number of external components for proper operation. Decoupling capacitors of 0.01F should be connected from each VDD pin to the ground plane, as close to the device as possible. A series termination resistor of 33 should be used to each clock output pin. Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS670-01. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature 0 to +70C Ambient Operating Temperature, ICS670-01I -40 to +85C Storage Temperature -65 to +150C Junction Temperature 125C Soldering Temperature 260C Recommended Operation Conditions Parameter Min. Ambient Operating Temperature Power Supply Voltage (measured in respect to GND) Typ. Max. Units 0 +70 C +3.0 +5.5 V DC Electrical Characteristics VDD=3.3V 10%, Ambient temperature -40 to +85C, unless stated otherwise Parameter Symbol Conditions Min. Typ. Max. Units 5.5 V Operating Voltage VDD 3.0 Input High Voltage VIH 2 Input Low Voltage VIL Output High Voltage VOH IOH = -12 mA Output Low Voltage VOL IOL = 12 mA Output High Voltage, CMOS level VOH IOH = -4 mA Operating Supply Current IDD No Load 35 mA Short Circuit Current IOS Each output 50 mA Internal Pull-up Resistor RPU OE, select pins 200 k Input Capacitance CIN OE, select pins 5 pF V 0.8 IDT(R) LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER 3 2.4 V V 0.4 VDD-0.4 V V ICS670-01 REV L 012315 ICS670-01 LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER ZDB AND MULTIPLIER AC Electrical Characteristics VDD = 3.3V 10%, Ambient Temperature -40 to +85C, unless stated otherwise Parameter Input Clock Frequency Symbol fIN Conditions Min. See table on page 2 Typ. 5 Output Clock Frequency PLL Stabilization Time tSTAB Input frequency 5 MHz to 160 MHz 4 Max. Units 160 MHz 160 MHz 10 s Output Rise Time tOR 0.8 to 2.0 V, no load 1.5 ns Output Fall Time tOF 2.0 to 0.8 V, no load 1.5 ns Output Clock Duty Cycle tDC measured at VDD/2 55 % 45 50 Input to Output Skew Note 1 100 ps Maximum Absolute Jitter short term 45 ps Maximum Jitter one sigma 15 ps Phase Noise, relative to carrier, 125 MHz (x5) 100 Hz offset -110 dBc/Hz 1 kHz offset -122 dBc/Hz 10 kHz -124 dBc/Hz 200 kHz -117 dBc/Hz Note 1: Rising edge of ICLK compared with rising edge of CLK2, with FBCLK connected to FBIN, and 15 pF load on CLK2. See graph on page 5 for skew vs. frequency and loading. Thermal Characteristics Parameter Thermal Resistance Junction to Ambient Thermal Resistance Junction to Case Symbol Conditions Min. Typ. Max. Units JA Still air 120 C/W JA 1 m/s air flow 115 C/W JA 3 m/s air flow 105 C/W 58 C/W JC IDT(R) LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER 4 ICS670-01 REV L 012315 ICS670-01 LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER ZDB AND MULTIPLIER Figure 1. Skew from ICLK to CLK2, with change in load capacitance (VDD = 3.3V) 300 200 Skew (ps) 100 0 -100 25 50 75 100 125 150 -200 -300 -400 CLK2 Frequency (MHz) Skew (ps) 20 pF Skew (ps) 10 pF Adjusting Input/Output Skew The data in Figure 1 can be used to adjust individual circuit characteristics and achieve the minimum possible skew between ICLK and CLK2. With a 125 MHz output, for example, having a total load capacitance of 15 pF will result in nearly zero skew between ICLK and CLK2. Note that the load capacitance includes board trace capacitance, input capacitance of the load being driven by the ICS670-01, and any additional capacitors connected to CLK2. Figure 2. Phase Noise for 125 MHz output, 25 MHz clock input (VDD = 3.3V) ICS670 Phase noise 0 -20 -40 L(f) dBc -60 -80 -100 -120 -140 10.E+0 100.E+0 1.E+3 10.E+3 100.E+3 1.E+6 10.E+6 offset frequency IDT(R) LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER 5 ICS670-01 REV L 012315 ICS670-01 LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER ZDB AND MULTIPLIER Package Outline and Package Dimensions (16-pin SOIC, 150 Mil. Narrow Body) Package dimensions are kept current with JEDEC Publication No. 95 16 Millimeters Symbol E Min A A1 B C D E e H h L H INDEX AREA 1 2 D A Inches Max Min 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 9.80 10.00 3.80 4.00 1.27 BASIC 5.80 6.20 0.25 0.50 0.40 1.27 0 8 Max .0532 .0688 .0040 .0098 .013 .020 .0075 .0098 .3859 .3937 .1497 .1574 0.050 BASIC .2284 .2440 .010 .020 .016 .050 0 8 h x 45 A1 C -Ce SEATING PLANE B L .10 (.004) C Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature 670M-01LF 670M-01LFT 670M-01ILF 670M-01ILFT 670M-01LF 670M-01LF 670M-01ILF 670M-01ILF Tubes Tape and Reel Tubes Tape and Reel 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC 0 to +70 C 0 to +70 C -40 to +85 C -40 to +85 C "LF" suffix to the part number denotes Pb-Free configuration, RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. Revision History Rev. Date Originator L 01/23/15 RDW Description of Change Updated AC characterization table with new parameter "PLL Stabilization Time". IDT(R) LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER 6 ICS670-01 REV L 012315 ICS670-01 LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER ZDB AND MULTIPLIER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 www.idt.com/go/clockhelp Corporate Headquarters Integrated Device Technology, Inc. www.idt.com (c) 2015 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA