Document 889-1 Shielded Coupled Inductors MSD1583 Excellent coupling coefficient (k 0.98) and 500 Vrms isolation makes the MSD1583 series of coupled inductors ideal for use in a variety of circuits including flyback, multioutput buck, SEPIC and Zeta. These parts provide high inductance, high efficiency and excellent current handling. In SEPIC topologies, the required inductance for each winding is half the value needed for two separate inductors, allowing selection of a part with lower DCR and higher current handling. + + D L1 C L2 VOUT C VIN - SW - Typical Flyback Converter L2 0.590 0.020 15,0 0,5 0.590 0.020 15,0 0,5 L1 D SW - Typical Buck Converter with auxiliary output D + L1 VIN 0.220 5,6 C 2 1 1 0.126 3,2 L1 3 2 1 3 4 0.311 Recommended 7,9 Land Pattern 0.091 2,3 L2 C VOUT - Typical SEPIC schematic 2 L2 4 + + VIN 0.165 4,2 - L2 C1 Q 0.075 1,9 0.146 3,7 + C1 Q - 4 VOUT C - Internal code 3 AUX + VIN 0.339 max 8,60 0.331 8,4 C + Dash number X + VOUT - Dot indicates pin1 123E D L1 C D Typical Zeta schematic C VOUT - If board traces are run in these areas, consider masking them to prevent shorting. Dimensions are in inches mm US +1-847-639-6400 sales@coilcraft.com UK +44-1236-730595 sales@coilcraft-europe.com Taiwan +886-2-2264 3646 sales@coilcraft.com.tw China +86-21-6218 8074 sales@coilcraft.com.cn Singapore + 65-6484 8412 sales@coilcraft.com.sg Document 889-1 Revised 1/5/16 (c) Coilcraft Inc. 2017 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Document 889-2 MSD1583 Shielded Coupled Inductors for SEPIC applications SRF Coupling Leakage Isat (A)5 Inductance2 DCR (Ohms)3 typ4 coefficient inductance 10% 20% Part number1 (H) typmax (MHz) typ typ (H) drop drop MSD1583-103ME_ 10 20% 0.026 0.031 16.0 0.98 0.33 11.7 13.3 MSD1583-123ME_ 12 20% 0.029 0.037 14.5 0.98 0.36 10.6 12.1 MSD1583-153ME_ 15 20% 0.039 0.045 12.0 0.99 0.38 9.50 10.8 MSD1583-183ME_ 18 20% 0.042 0.048 11.5 0.99 0.40 8.70 9.90 MSD1583-223ME_ 22 20% 0.054 0.065 10.5 0.99 0.40 7.90 8.95 MSD1583-333ME_ 33 20% 0.083 0.095 8.0 0.99 0.54 6.40 7.30 MSD1583-473ME_ 47 20% 0.100 0.115 7.1 0.99 0.46 5.40 6.10 MSD1583-683ME_ 68 20% 0.145 0.165 5.7 0.99 0.79 4.50 5.10 MSD1583-104KE_ 100 10% 0.230 0.260 5.1 >0.99 0.59 3.70 4.20 MSD1583-154KE_ 150 10% 0.340 0.380 3.7 >0.99 0.70 3.00 3.42 MSD1583-224KE_ 220 10% 0.420 0.460 3.2 >0.99 0.89 2.50 2.83 MSD1583-474KE_ 470 10% 0.950 1.04 2.2 >0.99 1.16 1.70 1.93 MSD1583-105KE_ 1000 10% 2.20 2.40 1.6 >0.99 2.02 1.17 1.32 1. When ordering, please specify termination and packaging codes: MSD1583-105KED Termination: E = RoHS compliant matte tin over nickel over phos bronze. Special order: Q = RoHS tin-silver-copper (95.5/4/0.5) or P = non-RoHS tin-lead (63/37). Packaging: D = 13 machine-ready reel. EIA-481 embossed plastic tape (300 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent. When leads are connected in parallel, inductance is the same value. When leads are connected in series, inductance is four times the value. 3. DCR is for each winding. When leads are connected in parallel, DCR is half the value. When leads are connected in series, DCR is twice the value. 4. SRF measured using an Agilent/HP 4191A or equivalent. When leads are connected in parallel, SRF is the same value. Typical L vs Current Irms (A) 30% both one drop windings6 winding7 14.5 3.68 5.20 13.2 3.54 5.00 11.8 3.18 4.50 10.8 3.04 4.30 9.80 2.44 3.45 8.00 2.16 3.05 6.70 1.98 2.80 5.50 1.56 2.20 4.60 1.24 1.75 3.75 1.06 1.50 3.10 0.92 1.30 2.12 0.65 0.92 1.45 0.42 0.60 5. DC current at which the inductance drops the specified amount from its value without current. It is the sum of the current flowing in both windings. 6. Equal current when applied to each winding simultaneously that causes a 40C temperature rise from 25C ambient. This information is for reference only and does not represent absolute maximum ratings. To predict temperature rise go to online calculator. 7. Maximum current when applied to one winding that causes a 40C temperature rise from 25C ambient. This information is for reference only and does not represent absolute maximum ratings. o predict temperature rise go to online calculator. 8. Electrical specifications at 25C. Refer to Doc 639 "Selecting Coupled Inductors for SEPIC Applications." Refer to Doc 362 "Soldering Surface Mount Components" before soldering. Coupled Inductor Core and Winding Loss Calculator This web-based utility allows you to enter frequency, peak-to-peak (ripple) current, and Irms current to predict temperature rise and overall losses, including core loss. Go to online calculator. Typical L vs Frequency 10000 10000 1000 H 1000 H 470 H 220 H 150 H 100 H 100 47 H 22 H 15 H 10 H 10 1 0.1 470 H 220 H 150 H 100 H 1000 Inductance (H) Inductance (H) 1000 10 1 47 H 22 H 15 H 10 H 100 10 100 1 0.1 Current (A) US +1-847-639-6400 sales@coilcraft.com UK +44-1236-730595 sales@coilcraft-europe.com Taiwan +886-2-2264 3646 sales@coilcraft.com.tw China +86-21-6218 8074 sales@coilcraft.com.cn Singapore + 65-6484 8412 sales@coilcraft.com.sg 1 10 100 Frequency (MHz) Document 889-2 Revised 1/5/16 (c) Coilcraft Inc. 2017 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Document 889-3 MSD1583 Shielded Coupled Inductors for Flyback applications Part number1 MSD1583-103ME_ MSD1583-123ME_ MSD1583-153ME_ MSD1583-183ME_ MSD1583-223ME_ MSD1583-333ME_ MSD1583-473ME_ MSD1583-683ME_ MSD1583-104KE_ MSD1583-154KE_ MSD1583-224KE_ MSD1583-474KE_ MSD1583-105KE_ Inductance at 0 A2 (H) 10 20% 12 20% 15 20% 18 20% 22 20% 33 20% 47 20% 68 20% 100 10% 150 10% 220 10% 470 10% 1000 10% Inductance at Ipk A3 typ (H) 7.0 8.4 10.5 12.6 15.4 23.1 32.9 47.6 70.0 105 154 329 700 DCR Leakage max inductance4 (Ohms) typ (H) 0.031 0.33 0.037 0.36 0.045 0.38 0.048 0.40 0.065 0.40 0.095 0.54 0.115 0.46 0.165 0.79 0.26 0.59 0.38 0.70 0.46 0.89 1.04 1.16 2.4 2.02 1. When ordering, please specify termination and packaging code: MSD1583-105KED Termination: E = RoHS compliant matte tin over nickel over phos bronze. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: D = 13 machine-ready reel. EIA-481 embossed plastic tape (300 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance is for the primary (L1), measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent. 3. Peak primary current drawn at minimum input voltage. 4. Leakage inductance is for the primary winding (L1) with the secondary winding (L2) shorted. 5. Electrical specifications at 25C. Refer to Doc 362 "Soldering Surface Mount Components" before soldering. Turns ratio 1:1 1:1 1:1 1:1 1:1 1:1 1:1 1:1 1:1 1:1 1:1 1:1 1:1 Ipk3 (A) 14.5 13.2 11.8 10.8 9.80 8.00 6.70 5.50 4.60 3.75 3.10 2.12 1.45 Core material Ferrite Core and winding loss Go to online calculator Environmental RoHS compliant, halogen free Terminations RoHS compliant matte tin over nickel over phos bronze. Other terminations available at additional cost. Weight: 3.7 - 4.4 g Ambient temperature -40C to +85C with (40C rise) Irms current. Maximum part temperature +125C (ambient + temp rise). Storage temperature Component: -40C to +125C. Tape and reel packaging: -40C to +80C Winding-to-winding isolation 500 Vrms, one minute Resistance to soldering heat Max three 40 second reflows at +260C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 300/13 reel; Plastic tape: 32 mm wide, 0.5 mm thick, 24 mm pocket spacing, 8.6 mm pocket depth PCB washing Tested with pure water or alcohol only. For other solvents, see Doc787_PCB_Washing.pdf. US +1-847-639-6400 sales@coilcraft.com UK +44-1236-730595 sales@coilcraft-europe.com Taiwan +886-2-2264 3646 sales@coilcraft.com.tw China +86-21-6218 8074 sales@coilcraft.com.cn Singapore + 65-6484 8412 sales@coilcraft.com.sg Document 889-3 Revised 1/5/16 (c) Coilcraft Inc. 2017 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Coilcraft: MSD1583-103MED MSD1583-153MEB MSD1583-183MED MSD1583-333MEB MSD1583-154KEB MSD1583683MED MSD1583-104KEB MSD1583-123MED MSD1583-104KED MSD1583-224KEB MSD1583-223MED MSD1583-473MEB MSD1583-103MEB MSD1583-105KEB MSD1583-474KED MSD1583-123MEB MSD1583224KED MSD1583-473MED MSD1583-683MEB MSD1583-105KED MSD1583-153MED MSD1583-333MED MSD1583-223MEB MSD1583-183MEB MSD1583-154KED MSD1583-474KEB