V23134M0052C642 - TE CONNECTIVITY

11-2013, Rev. 1113

www.te.com

a TE Connectivity Ltd. company.

Datasheets and product speciﬁcation ac-

cording to IEC 61810-1 and to be used only

together with the ‘Deﬁnitions’ section.

Datasheets and product data is subject to the

terms of the disclaimer and all chapters of

the ‘Deﬁnitions’ section, available at

http://relays.te.com/definitions

Datasheets, product data, ‘Deﬁnitions’ sec-

tion, application notes and all speciﬁcations

are subject to change.

Contact Data

Contact arrangement 1 form A, 1 NO/1 NO (2x87) 1 form U, 2 NO 1 form C, 1 CO

Contact gap >0.8mm

Rated voltage 12VDC 24VDC 12VDC 24VDC 12VDC 24VDC 24VDC1)

Limiting continuous current NO NO NO NO NO/NC NO/NC NO/NC

23°C 60A 60A 2x32A 2x32A 60/45A 60/45A 60/45A

85°C 40A 40A 2x25A 2x25A 40/30A 40/30A 40/30A

125°C 17A 17A 2x11A 2x11A 17/12A 17/12A 17/12A

Limiting making current2)

NO/NC 120A 120A 2x100A 2x100A 120/45A 120/45A 120/45A

Limiting breaking current

NO/NC 60A 20A 2x40A 2x15A 60/40A 20/15A 30/20A

Limiting short-time current

overload current, ISO 8820-33):

1.35 x 40A, 1800s 1.35 x 40A, 1800s 1.35 x 40A, 1800s

2.00 x 40A, 5s 2.00 x 40A, 5s 2.00 x 40A, 5s

3.50 x 40A, 0.5s 3.50 x 40A, 0.5s 3.50 x 40A, 0.5s

6.00 x 40A, 0.1s 6.00 x 40A, 0.1s 6.00 x 40A, 0.1s

Jump start test

ISO 16750-1 24VDC for 5min conducting nominal current at 23°C

Contact material silver based

Min. recommended contact load4) 1A at 5VDC

Initial voltage drop

NO contact at 10A, typ./max. 15/200mV 15/200mV 2x15/200mV 2x15/200mV 15/200mV 15/200mV 15/200mV

NC contact at 10A, typ./max. 20/250mV 20/250mV 20/250mV

Frequency of operation

at nominal load 6 ops./min (0.1Hz)

Operate/release time typ. 7/2ms5)

Electrical endurance

resistive load at 14VDC >2x105 ops. >2x105 ops. >2x105 ops.

40A 2x25A 40A (NO)

resistive load at 28VDC >1x105 ops. >1x105 ops. >1x105 ops. 1x105 ops.

20A 2x15A 20A (NO) 30A (NO)

>5x105 ops.

10A (NC)

Mechanical endurance

DC coil >1x107ops.

1) Special high performance 24VDC version with contact gap >0.8mm, part number V23134-A0056-X432/-X433 (see part number table).

2) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 14VDC for 12VDC or 28VDC for 24VDC load voltages. For a load current duration of

maximum 3s for a make/break ratio of 1:10.

3) Current and time are compatible with circuit protection by a typical automotive fuse. Relay will make, carry and break the speciﬁed current.

4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/

5) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher

risk of contact tack welding.

Power Relay F4

Automotive Relays

Plug-in Mini ISO Relays

n Pin assignment similar to ISO 7588 part 1

n Plug-in or PCB terminals

n Also available for 42VDC applications

Customized versions on request

– 24VDC versions with contact gap >0.8mm

– Integrated components (e.g. resistor, diode)

– Customized marking/color

– Special covers (e.g. notches, release features, brackets)

– Various contact arrangements and materials

– For latching (bistable) version refer to Power Relay F7 A Latching

or Mini Relay Latching

– For shrouded/weatherproof dust cover versions refer to

Shrouded Power Relay F4 A and VF4 A

Typical applications

Cross carline up to 40A for example: ABS control, blower fans, car alarm,

cooling fan, Electric Power Steering, energy management, engine control,

fuel pump, heated front screen, lamps: front, rear, fog light, main switch/

supply relay, valves, wiper control.

F134co_fcw1

11-2013, Rev. 1113

www.te.com

a TE Connectivity Ltd. company.

Datasheets and product speciﬁcation ac-

cording to IEC 61810-1 and to be used only

together with the ‘Deﬁnitions’ section.

Datasheets and product data is subject to the

terms of the disclaimer and all chapters of

the ‘Deﬁnitions’ section, available at

http://relays.te.com/definitions

Datasheets, product data, ‘Deﬁnitions’ sec-

tion, application notes and all speciﬁcations

are subject to change.

Power Relay F4 (Continued)

Automotive Relays

Plug-in Mini ISO Relays

Max. load DC breaking capacity

Load limit curve 1: arc extinguishes during transit time (CO contact).

Load limit curve 2: safe shutdown, no stationary arc (NO contact).

Load limit curves measured with low inductive resistors veriﬁed for 1000 switching events.

Coil Data

Rated coil voltage 12/24VDC

Coil versions, DC coil

Coil Rated Operate Release Coil Rated coil

code voltage voltage voltage resistance6) power6)

VDC VDC VDC Ω±10% W

052 12 7.2 1.6 90 1.6

053 24 14.4 3.2 324 1.8

056 24 16 4 268 2.1

All ﬁgures are given for coil without pre-energization, at ambient temperature +23°C.

Coil operating range

Does not take into account

the temperature rise due to

the contact current

E = pre-energization

TE0701-J1

Does not take into account the temperature rise due to the contact current E=pre-

energization..

6) Without components in parallel.

Insulation Data

Initial dielectric strength

between open contacts 500Vrms

between contact and coil 500Vrms

between adjacent contacts 500Vrms

Load dump test

ISO 7637-1 (12VDC), test pulse 5 Vs=+86.5VDC

ISO 7637-2 (24VDC), test pulse 5 Vs=+200VDC

Other Data

EU RoHS/ELV compliance compliant

Ambient temperature DC coil -40 to +125°C

Protection to heat and ﬁre UL94-HB or better7)

Climatic cycling with condensation

EN ISO 6988 6 cycles, storage 8/16h

Temperature cycling

IEC 60068-2-14, Nb 10 cycles, -40/+85°C (5°C/min)

Damp heat cyclic

IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55°C

Damp heat constant

IEC 60068-2-3, Ca 56 days

Category of environmental protection,

IEC 61810 RTI – dustproof, RT III – sealed

Degree of protection, IEC 60529 IP54 (dustproof), IP67 (sealed)

Corrosive gas

IEC 60068-2-42 10±2cm3/m3 SO2, 10 days

IEC 60068-2-43 1±0.3cm3/m3 H2S, 10 days

Vibration resistance (functional)

IEC 60068-2-6 (sine sweep) 10 to 500Hz > 5g8)

Shock resistance (functional)

IEC 60068-2-27 (half sine) 11ms >20g8)

Drop test, free fall

IEC 60068-2-32 1m onto concrete

Terminal type plug-in, QC/PCB

Cover retention

axial force 150N

pull force 150N

push force 150N

Terminal retention

pull force 100N

push force 100N

resistance to bending, force applied to front9) 10N

resistance to bending, force applied to side9) 10N

torque 0.3Nm

Weight approx. 35g (1.2oz)

Packaging unit

plug-in/PCB 315 pcs.

plug-in with bracket 200 pcs.

7) Refers to used materials.

8) No change in the switching state >10μs. Valid for NC contacts, NO contact values

signiﬁcantly higher.

9) Values apply 2mm from the end of the terminal. When the force is removed, the terminal

must not have moved by more than 0.3mm.

Accessories

For details see datasheet Connectors for Mini ISO Relays

11-2013, Rev. 1113

www.te.com

a TE Connectivity Ltd. company.

Datasheets and product speciﬁcation ac-

cording to IEC 61810-1 and to be used only

together with the ‘Deﬁnitions’ section.

Datasheets and product data is subject to the

terms of the disclaimer and all chapters of

the ‘Deﬁnitions’ section, available at

http://relays.te.com/definitions

Datasheets, product data, ‘Deﬁnitions’ sec-

tion, application notes and all speciﬁcations

are subject to change.

Power Relay F4 (Continued)

Automotive Relays

Plug-in Mini ISO Relays

Terminal Assignment

1 form A, 1 NO

NOR_2x87

1 form A, 1 NO (2x87)

with resistor

NOR_SD

1 form A, 1 NO

with resistor & serial diode

COR

1 form C, 1 CO

with resistor

COD

1 form C, 1 CO

with diode

NOR

1 form A, 1 NO

with resistor

1 form C, 1 CO

NO_2x87

1 form A, 1 NO (2x87)

DNO

1 form U, 2 NO

3086

85 87 87

3086

87 87a

85 87 87a

3086

85 87 87a

3086

87 87

3086

87 87b

Power Relay F4 with PCB terminals View of the terminals (bottom view) Mounting hole layout (bottom view)

For the make contact (2x87), pin 87a = 87;

for the double make contact, pin 87a = 87b.

TE1654-91

TE0907-B1

For the make contact (2 x pin 87)

pin 87a = 87.

For the twin make contact,

pin 87a = 87b.

16.9 ±0.3

4.5 ±0.3

8.4 ±0.25

17.9 ±0.25

8.0 ±0.25

2.7 ±0.5

TE1655-H1

Dimensions

Power Relay F4 with quick connect (QC) terminals View of the terminals (bottom view)

Measurement

reference plane

0.3

TE1093-S1

For the make contact (2x87), pin 87a = 87;

for the double make contact, pin 87a = 87b.

TE1088-R1

11-2013, Rev. 1113

www.te.com

a TE Connectivity Ltd. company.

Datasheets and product speciﬁcation ac-

cording to IEC 61810-1 and to be used only

together with the ‘Deﬁnitions’ section.

Datasheets and product data is subject to the

terms of the disclaimer and all chapters of

the ‘Deﬁnitions’ section, available at

http://relays.te.com/definitions

Datasheets, product data, ‘Deﬁnitions’ sec-

tion, application notes and all speciﬁcations

are subject to change.

Power Relay F4 (Continued)

Automotive Relays

Plug-in Mini ISO Relays

Product code structure Typical product code V23134 -A 0 052 -C642

Type

V23134 Power Relay F4

Contact arrangement

A 1 form C, 1 CO C 1 form A, 1 NO (2x87)

B 1 form A, 1 NO K 1 form A, 1 NO (non ISO)

M 1 form U, 2 NO

Cover

0 Standard 1 Bracket at terminal 30 ISO

2 Bracket at terminal 86 ISO

Coil

052 12VDC 053 24VDC

056 24VDC (contact gap >0.8mm)

Terminal/arrangement

C642 Plug-in/NO C643 Plug-in/CO

G242 PCB/NO G243 PCB/CO

Xnnn Customized (nnn: version number)

Product code Arrangement Version Coil suppr. Circuit1) Coil Arrangement Terminals Part number

V23134-A0052-C643 1 form C, 1 CO Standard CO 12VDC Silver based Plug-in, QC 2-1393302-2

V23134-A0052-G243 PCB 2-1393302-3

V23134-A0052-X278 R 560Ω COR Plug-in, QC 4-1393302-1

V23134-A0053-C643 CO 24VDC 5-1393302-1

V23134-A0053-G243 PCB 5-1393302-2

V23134-A0056-X4322) D (cathode 86) COD Plug-in, QC 1-1414167-0

V23134-A0056-X4332) R 1200Ω COR 1-1414168-0

V23134-A1052-C643 Bracket CO 12VDC 5-1393302-8

V23134-A1052-X2944) R 560Ω COR 6-1393302-0

V23134-A1053-C643 CO 24VDC 6-1393302-3

V23134-A1053-X2954) R 1200Ω COR 6-1393302-4

V23134-B0052-C642 1 form A, 1 NO Standard NO 12VDC 7-1393302-5

V23134-B0052-G242 PCB 7-1393302-7

V23134-B0052-X2706) R 680Ω NOR Plug-in, QC 1-1414099-0

V23134-B0052-X506 R 560Ω NOR_SD3) 4-1414992-3

V23134-B0053-C642 NO 24VDC 1393303-9

V23134-B0053-G242 PCB 1-1393303-0

V23134-B1052-C642 Bracket 12VDC Plug-in, QC 3-1393303-4

V23134-B1053-C642 24VDC 3-1393303-7

V23134-B1053-X2964) R 1200Ω NOR 3-1393303-8

V23134-C0052-C642 1 form A, 1 NO (2x87) Standard NO_2x87 12VDC 3-1393303-9

V23134-C0053-C642 24VDC 4-1393303-4

V23134-C1052-C642 Bracket 12VDC 4-1393303-7

V23134-C1052-X2804) 5) R 560Ω NOR_2x87 4-1393303-8

V23134-C1053-C642 NO_2x87 24VDC 5-1393303-0

V23134-K1052-X399 1 form A, 1 NO R 560Ω NOR non ISO 12VDC Plug-in, QC/non ISO 1-1393305-1

V23134-M0052-C642 1 form U, 2 NO Standard DNO Plug-in, QC 5-1393304-6

V23134-M0052-G242 PCB 5-1393304-7

V23134-M0053-C642 24VDC Plug-in, QC 6-1393304-7

V23134-M0053-G242 PCB 6-1393304-8

V23134-M1052-C642 Bracket 12VDC Plug-in, QC 7-1393304-1

V23134-M1053-C642 24VDC 7-1393304-4

1) See terminal assignment diagrams.

2) Special feature: contact gap >0.8mm.

3) Serial diode.

4) No hole in terminal 30.

5) No hole in terminal 87a.

6) No holes in all terminals.

Other types on request.

This list represents the most common types and does not show all variants covered by this datasheet.