CERAMIC CHIP CAPACITORS FEATURES * C0G (NP0), X7R, X5R, Z5U and Y5V Dielectrics * 10, 16, 25, 50, 100 and 200 Volts * Standard End Metalization: Tin-plate over nickel barrier * Available Capacitance Tolerances: 0.10 pF; 0.25 pF; 0.5 pF; 1%; 2%; 5%; 10%; 20%; and +80%-20% * Tape and reel packaging per EIA481-1. (See page 92 for specific tape and reel information.) Bulk Cassette packaging (0402, 0603, 0805 only) per IEC60286-6 and EIAJ 7201. * RoHS Compliant CAPACITOR OUTLINE DRAWINGS TIN PLATE L W B T NICKEL PLATE S ELECTRODES CONDUCTIVE METALLIZATION DIMENSIONS--MILLIMETERS AND (INCHES) METRIC SIZE CODE L - LENGTH W - WIDTH 0201* 0603 0.6 (.024) .03 (.001) 0.3 (.012) .03 (.001) 0.15 (.006) .05 (.002) N/A 0402* 1005 1.0 (.04) .05 (.002) 0.5 (.02) .05 (.002) 0.20 (.008) -.40 (.016) 0.3 (.012) B - BANDWIDTH 0603 1608 1.6 (.063) .15 (.006) 0.8 (.032) .15 (.006) 0.35 (.014) .15 (.006) 0.7 (.028) 0805* 2012 2.0 (.079) .20 (.008) 1.25 (.049) .20 (.008) 0.50 (.02) .25 (.010) 0.75 (.030) 1206* 3216 3.2 (.126) .20 (.008) 1.6 (.063) .20 (.008) 0.50 (.02) .25 (.010) N/A 1210* 3225 3.2 (.126) .20 (.008) 2.5 (.098) .20 (.008) 1808 4520 4.5 (.177) .30 (.012) 2.0 (.079) .20 (.008) See page 78 for thickness dimensions. 0.50 (.02) .25 (.010) N/A 0.60 (.024) .35 (.014) N/A N/A 1812 4532 4.5 (.177) .30 (.012) 3.2 (.126) .30 (.012) 0.60 (.024) .35 (.014) 1825* 4564 4.5 (.177) .30 (.012) 6.4 (.252) .40 (.016) 0.60 (.024) .35 (.014) N/A 2220 5650 5.6 (.220) .40 (.016) 5.0 (.197) .40 (.016) 0.60 (.024) .35 (.014) N/A 2225 5664 5.6 (.220) .40 (.016) 6.3 (.248) .40 (.016) 0.60 (.024) .35 (.014) N/A MOUNTING TECHNIQUE Solder Reflow Solder Wave + or Solder Reflow Solder Reflow * Note: Indicates EIA Preferred Case Sizes (Tightened tolerances apply for 0402, 0603, and 0805 packaged in bulk bassette, see page 96.) + For extended value 1210 case size - solder reflow only. CAPACITOR ORDERING INFORMATION (Standard Chips - For C 0805 C 103 K 5 R A C* CERAMIC SIZE CODE SPECIFICATION C - Standard CAPACITANCE CODE Expressed in Picofarads (pF) First two digits represent significant figures. Third digit specifies number of zeros. (Use 9 for 1.0 through 9.9pF. Use 8 for 0.5 through 0.99pF) (Example: 2.2pF = 229 or 0.50 pF = 508) CAPACITANCE TOLERANCE B - 0.10pF J - 5% C - 0.25pF K - 10% D - 0.5pF M - 20% F - 1% P - (GMV) - special order only G - 2% Z - +80%, -20% 72 Military see page 87) END METALLIZATION C-Standard (Tin-plated nickel barrier) FAILURE RATE LEVEL A- Not Applicable TEMPERATURE CHARACTERISTIC Designated by Capacitance Change Over Temperature Range G - C0G (NP0) (30 PPM/C) R - X7R (15%) (-55C + 125C) P- X5R (15%) (-55C + 85C) U - Z5U (+22%, -56%) (+10C + 85C) V - Y5V (+22%, -82%) (-30C + 85C) VOLTAGE 1 -- 100V 1 100V 3 - 25V 3 - 25V 2 - 200V 4 - 16V 2 200V 4 - 16V 5 - 50V 8 - 10V 5 50V 8 - 10V 6 - 35V 9 - 6.3V * Part Number Example: C0805C103K5RAC (14 digits - no spaces) 7 - 4V 7 - 4V 9 - 6.3V (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 Ceramic Surface Mount T THICKNESS S SEPARATION minimum EIA SIZE CODE CERAMIC CHIP/STANDARD C0G CAPACITANCE RANGE - 1210, 1812, 1825, 2220, 2225 CAP. PF 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10,000 12,000 15,000 18,000 22,000 27,000 33,000 CAP CODE 100 120 150 180 220 270 330 390 470 560 680 820 101 121 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 Cap CAP. Cap pF Code TOL. 0.5-2.4 508-249 C ,D2.7-9.1 J279-919 ,M ,K 10.0-13.0 100-130 C ,D ,K ,M 15.0-24.0 J150-240 27.0-51.0 C ,D G ,J270-510 ,K ,M 56.0-82.0 560-820 C91.0-360.0 ,D G ,J910-361 ,K ,M C ,D 390.0 ,M 391 G ,J ,K 430.0 431 D,F ,M ,G ,J ,K 470.0 471 D,F ,M ,G ,J ,K 510.0 511 560.0 561 D,F ,M ,G ,J ,K 620.0 621 D,F ,M ,G ,J ,K 680.0 681 750.0 751 F ,M ,G ,J ,K 820.0 821 F ,M ,G ,J ,K 910.0 911 F,G ,J ,K ,M 102 1,000.0 112 1,100.0 F,G ,J ,K ,M 122 1,200.0 F,G ,J ,K ,M 132 1,300.0 152 1,500.0 F,G ,J ,K ,M 162 1,600.0 F,G ,J ,K ,M 182 1,800.0 F,G ,J ,K ,M 202 2,000.0 222 2,200.0 F,G ,J ,K ,M 242 2,400.0 F,G ,J ,K ,M 272 2,700.0 302 3,000.0 F,G ,J ,K ,M 332 3,300.0 F,G ,J ,K ,M 362 3,600.0 392 3,900.0 F,G ,J ,K ,M 432 4,300.0 F,G ,J ,K ,M 472 4,700.0 F,G ,J ,K ,M 512 5,100.0 562 5,600.0 F,G ,J ,K ,M 622 6,200.0 F ,M ,G ,J ,K 682 6,800.0 752 7,500.0 F,G ,J ,K ,M 822 8,200.0 F ,M ,G ,J ,K 912 9,100.0 F,G ,J ,K ,M 103 10,000.0 123 12,000.0 F,G ,J ,K ,M 153 15,000.0 F,G ,J ,K ,M 183 18,000.0 223 22,000.0 F,G ,J ,K ,M 273 27,000.0 F ,M ,G ,J ,K 333 33,000.0 F,G ,J ,K ,M 473 47,000.0 563 56,000.0 F ,M ,G ,J ,K 683 68,000.0 F,G ,J ,K ,M 823 82,000.0 104 100,000.0 F,G ,J ,K ,M 124 120,000.0 F,G ,J ,K ,M 154 150,000.0 224 220,000.0 F,G ,J ,K ,M 274 270,000.0 F ,M ,G ,J ,K 334 330,000.0 F,G ,J ,K ,M 474 470,000.0 564 560,000.0 F,G ,J ,K ,M Cap Tolerance 10V D . FB D FB K,MFBFB D J,K,M FB DFB G,J,K,MFBFB D,F,G,J,K,M FBFB FB F,G,J,K,M FB FB F,G,J,K,MFBFB FB F,G,J,K,MFBFB F,G,J,K,MFBFB FB F,G,J,K,M FB FB F,G,J,K,MFBFB F,G,J,K,MFBFB FB F,G,J,K,M FB FB F,G,J,K,MFBFB F,G,J,K,MFBFB FB F,G,J,K,M FB FB FB F,G,J,K,M FB FB F,G,J,K,MFBFB F,G,J,K,MFBFB FB F,G,J,K,M FB FB F,G,J,K,MFBFB F,G,J,K,MFBFB FB F,G,J,K,M FB FB FB F,G,J,K,M FB FB F,G,J,K,MFBFB F,G,J,K,MFBFB FB F,G,J,K,M FB FB F,G,J,K,MFBFB F,G,J,K,MFBFB FB F,G,J,K,M FB FB F,G,J,K,MFBFB F,G,J,K,MFBFB FB F,G,J,K,MFBFB FB F,G,J,K,M FF FB F,G,J,K,MFBFB F,G,J,K,MFBFB FB F,G,J,K,M FB FB F,G,J,K,MFBFB F,G,J,K,MFBFC FB F,G,J,K,M FC FB FB F,G,J,K,M FE FB F,G,J,K,MFC FF F,G,J,K,MFC FG FB F,G,J,K,M FG FB F,G,J,K,MFFFB F,G,J,K,MFFFB FB F,G,J,K,M FB FF F,G,J,K,MFFFB FB F,G,J,K,MFFFB F,G,J,K,MFG FB FB F,G,J,K,M FB FC F,G,J,K,M FC F,G,J,K,M FE FF F,G,J,K,M FG FG F,G,J,K,M FH F,G,J,K,M FK+ F,G,J,K,M F,G,J,K,M F,G,J,K,M F,G,J,K,M C1210* 16V 25V FB FB FB FBFB FB FB FBFB FB FB FBFB FB FB FBFB FB FBFB FB FB FBFB FB FB FBFB FB FB FBFB FB FB FBFB FB FB FBFB FB FB FB FB FB FBFB FB FB FBFB FB FB FBFB FB FB FBFB FB FB FB FB FB FBFB FB FB FBFB FB FB FBFB FB FB FBFB FB FB FBFB FB FB FBFB FB FBFB FF FF FBFB FB FB FBFB FB FB FBFB FB FC FEFC FC FC FE FE FE FGFF FF FG FCFG FG FG FFFB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FE FE FG FG FH FH FK+ FK+ C1812* C1825* 50V 100V 200V 50V 100V 200V FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB GB GB GB FB FB FB FB FB FB GB GB GB FB FB FB FB FB FB GB GB GB FB FB FB FB FB FB GB GB GB FB FB FB FB FB FB GB GB GB FB FB FB FB FB FB GB GB GB FB FB FC FB FB FE GB GB GB FB FB FE FB FB FE GB GB GB FB FC FE FB FC FG GB GB GB FB FC FC FB FC FC GB GB GB FB FC FF FB FF FF GB GB GB FB FF FF FB FF FF GB GB GB FB FF FF FF FG FG GB GB GD FB FG FG FB FG FG GB GB GH FB FG FB FG GB GB GJ FC FC FC FC GB GH FE FE FF FF GB GH FG FB GB GG FG FB GB GB FB FB GB GB FB FB GB GB FB FB GB GB FB FB GB GB FB FE GB GB FB FF GB GB FC FG GB GB FF FH GB GB FG FM+ GB GD FH GB GH FM+ GD GN GK C2220 C2225 50V 100V 200V 50V 100V 200V 50V 100V 200V HB HB HB HB HB HB KB KB KB HB HB HB KB KB KB HB HB HB JB JB KB KB KB HB HB HB JB JB KB KB KB HB HB HB HB HB HB HB HB HB HE HE HF HE HE JB JB JB JB JB JB JB JB JB JB JB JB JB JB JB JB JD JG JB JB JB JB JB JB JB JB JB JB JB JB JB JB JD JF JH KB KB KB KB KB KB KB KB KB KB KB KB KE KB KB KE F,G ,J ,K ,M X7R CAPACITANCE RANGE - 0402, 0603, 0805, 1206 Cap pF Cap Code Cap Tol 150 180 220 270 330 390 470 560 680 820 1,000 1,200 1,500 1,800 2,200 2,700 3,300 3,900 4,700 5,600 6,800 8,200 10,000 12,000 15,000 18,000 22,000 27,000 33,000 39,000 47,000 56,000 68,000 82,000 100,000 120,000 150,000 180,000 220,000 270,000 330,000 390,000 470,000 560,000 680,000 820,000 1,000,000 1,200,000 1,500,000 1,800,000 2,200,000 2,700,000 3,300,000 3,900,000 4,700,000 5,600,000 6,800,000 8,200,000 10,000,000 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 275 335 395 475 565 685 825 106 J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M J, K, M C0603 C0402 6.3V BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB 10V BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB 16V BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB 25V BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB 50V BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB C0805 6.3V 10V 16V 25V 50V CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CD CC* CC* CC* CD 100V 200V 6.3V CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DD DC DC DC DC DD DD DG DD DD DD DD DD DE DG DG DG C1206 10V 16V 25V 50V DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DD DC DC DC DC DD DD DG DD DD DD DD DD DE DG DG DG DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DD DC DC DC DC DD DD DG DD DD DD DD DD DE DG DG DG DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DD DC DC DC DC DD DD DG DD DG DG DG DG DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DD DD DD DD DD 100V 200V 6.3V DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DD DD DD DE DE DE DE DE DG DG DD DE DE DH DH DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DE DE DE DG DG EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EB EB EB EC ED EE EF EF ED EF EF ED EN ED EF EF+ EH+ EH+ EH+ EH+ 10V 16V 25V 50V EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EB EB EB EC ED EE EF EF ED EF EF ED EN ED EF EF+ EH+ EH+ EH+ EH+ EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EB EB EB EC ED EE EF EF ED EF EF ED EN ED EF EF+ EH+ EH+ EH+ EH+ EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EB EB EB EC ED EE EF EG EG EG EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EC EC EC EC EC ED ED ED EH EH EH EH * Capacitance K or M. ontact KEMET Sales Rep for J tolerance availability. +_ Reflow Only. NOTE: For non-standard capacitance values or voltages, contact your local KEMET sales representative. # X7R dielectric - Extended Range Values - Cap and DF measured @ 0.5 Vrms. Improved product with higher ratings and tighter capacitance tolerance product may be substituted within the same size (length, width, and thickness) at KEMET's option. Reels with such substitutions will be marked with the improved KEMET part numbers. page 78Thickness for Thickness Reference Chart. SeeSee page 63 for CodeCode Reference Chart. 74 (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 EF EH EH+ 100V 200V EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EB EB EB EB EC EC EC EC EM EG EG EG EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB ED ED ED ED EM EM EG CERAMIC CHIP/STANDARD X7R CAPACITANCE RANGE - 1210, 1808, 1812, 1825, 2220, 2225 Cap pF 2,200 2,700 3,300 3,900 4,700 5,600 6,800 8,200 10,000 12,000 15,000 18,000 22,000 27,000 33,000 39,000 47,000 56,000 68,000 82,000 100,000 120,000 150,000 180,000 220,000 270,000 330,000 390,000 470,000 560,000 680,000 820,000 1,000,000 1,200,000 1,500,000 1,800,000 2,200,000 2,700,000 3,300,000 3,900,000 4,700,000 5,600,000 6,800,000 8,200,000 10,000,000 12,000,000 15,000,000 18,000,000 22,000,000 47,000,000 Cap Cap Tol. Code 6.3V 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 275 335 395 475 565 685 825 106 126 156 186 226 476 J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M M FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FH FH FH FJ FE FF FG FC+ FF+ FG+ FH+ FH+ C1210 C1808 10V 16V 25V 50V FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FH FH FH FJ FE FF FG FC+ FF+ FG+ FH+ FH+ FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FH FH FH FJ FE FF FG FC+ FF+ FG+ FH+ FH+ FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FH FH FH FJ FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FG FG FG FG FM FM FG+ FS+ 100V 200V FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FD FD FD FD FD FD FD FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FF FG 50V LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD C1812 100V 200V LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD FD FM 25V 50V GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GC GC GE GE GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GC GC GE GE FT* C1825 100V 200V GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GG GG GG GG GG GG GG GG 50V GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GE GF GG GG GG GG GJ HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HC HD HF GO GK* C2220 100V 200V HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HD HD 25V HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HD HD HD HD HF HF 50V JC JC JC JC JC JC JC JC JC JC JD JF JC JC JC JC JC JC JC JC JC JC JD JF JF JO C2225 100V 200V JC JC JC JC JC JD JF JF JC JC JC JC JC JC JC JC JC JC JD JD JF JF 50V KC KC KC KC KC KC KC KC KC KB KB KB KB KB KB KB KB KB KC KD KD 100V 200V KC KC KC KC KC KC KC KC KC KC KC KC KC KC KC KC KD KC KC KC KC KC KC KC KC KC KC KC KC KD KD KD KE KE KE GK* FM+ FS+ GK* JO FS+ FS+ FS+ JO * Capacitance tolerance K or M. Contact your local KEMET Sales Rep for J tolerance availablity. + Reflow Only NOTE: For non-standard capacitance values or voltages, contact your local KEMET sales representative. 50 Volt Ceramic Chips can be used for 63 volt applications. # Extended Range Values - Cap and DF measured @ 0.5 Vrms. M tolerance only Ceramic Surface Mount Improved product with higher ratings and tighter capacitance tolerance product may be substituted within the same size (length, width, and thickness) at KEMET's option. Reels with such substitutions will be marked with the improved KEMET part numbers. Y5V CAPACITANCE RANGE Cap pF Cap Code 22,000 27,000 33,000 39,000 47,000 56,000 68,000 82,000 100,000 120,000 150,000 180,000 220,000 270,000 330,000 390,000 470,000 560,000 680,000 820,000 1,000,000 1,200,000 1,500,000 1,800,000 2,200,000 3,300,000 4,700,000 5,600,000 6,800,000 10,000,000 15,000,000 22,000,000 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 335 475 565 685 106 156 226 C0402* C0603* Cap Tol. 6.3V 10V 16V 6.3V 10V 16V Z BB BB BB CB CB CB Z BB BB BB CB CB CB Z BB BB BB CB CB CB Z BB BB BB CB CB CB Z BB BB BB CB CB CB Z BB BB BB CB CB CB Z BB BB BB CB CB CB Z BB BB BB CB CB CB Z BB BB BB CB CB CB Z CC CC CC Z CC CC CC Z CC CC CC Z BB CC CC CC Z CC CC CC Z CC CC CC Z CC CC CC Z BB CC CC CC Z CC CC Z CC CC Z CC CC Z BB CC CC Z Z Z Z Z Z Z Z Z C0805* 25V 6.3V 10V CB CB CB CB CB CB CB CB CB CC DC DC CC DC DC CC DC DC CC DC DC CC DC DC CC DC DC DC DC DC DC DD DD DE DE DG DG DG DG DC DC DC DC DD DD DD DD DE DE DH DH DH DH DH DH DH DH 16V 25V 50V DC DC DC DD DD DD DD DD DD DC DC DC DC DC DC DC DC DD DC DC DC DC DC DC DC DC DD DD DE DE DG DG DG DG DC DC DD DD DH DH C1206* C1210* 6.3V 10V 16V 25V 50V 6.3V 10V 16V 25V 50V EB EB EB EB EB EB EB EB EB EC EB EB EB EC EB EB EB EG EC EC EC EE EF EM EJ EJ EJ Z Z EH EC EB EB EB EC EB EB EB EG EC EC EC EE EF EM EJ EJ EJ EC EB EB EB EC EB EB EB EG EC EC EC EE EF EM EJ EC EB EB EB EC EB EB EB EG FD FD FD FD FD FD FD FF FH FD FD FD FD FE FG FG FH FH FH FT FD FD FD FD FD FD FD FF FH FD FD FD FD FE FG FG FH FH FH FT FD FD FD FD FD FD FD FF FH FD FD FD FD FE FG FG FH FH FH FM FD FD FD FD FD FD FD FF FH FD FD FD FD FD FD FD FF FH NOTE: For non-standard capacitance values or voltages, contact your local KEMET sales representative. 50 Volt Ceramic Chips can be used for 63 volt applications. * EIA preferred chip sizes + Reflow only See page 78 for Thickness Code Reference Chart (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630 75 CERAMIC CHIP CAPACITORS Thickness Code Reference Chart Packaging Quantity Based on Finished Chip Thickness Specifications Thickness Code Chip Size Chip Thickness Range (mm) Qty per Reel 7" Plastic Qty per Reel 13" Plastic Qty per Reel 7" Paper Qty per Reel 13" Paper Qty per Bulk Cassette AA BB CB CC CD DB DC DD DE DF DG DH DJ DK DL EB EC ED EE EF EG EH EJ EK EL EM EN FB FC FD FE FF FG FH FJ FK FL FM FN FO FP FQ FR FS FT LD GB GC GD GE GF GG GH GJ GK GL GM GN GO HB HC HD HE HF JB JC JD JE JF JG JH JO KB KC KD KE 0201 0402 0603 0603 0603 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 1206 1206 1206 1206 1206 1206 1206 1206 1206 1206 1206 1206 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1808 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1825 1825 1825 1825 1825 2220 2220 2220 2220 2220 2220 2220 2220 2225 2225 2225 2225 0.30 0.03 0.50 0.05 0.80 0.07 0.80 0.10 0.80 0.15 0.60 0.10 0.78 0.10 0.90 0.10 1.00 0.10 1.10 0.10 1.25 0.15 1.25 0.20 1.25 0.20 1.25 0.15 0.95 0.10 0.78 0.10 0.90 0.10 1.00 0.10 1.10 0.10 1.20 0.15 1.60 0.15 1.60 0.20 1.70 0.20 0.80 0.10 1.15 0.15 1.25 0.15 0.95 0.10 0.78 0.10 0.90 0.10 0.95 0.10 1.00 0.10 1.10 0.10 1.25 0.15 1.55 0.15 1.85 0.20 2.10 0.20 1.40 0.15 1.70 0.20 1.85 0.20 1.50 0.20 1.60 0.20 2.50 0.22 2.25 0.20 2.50 0.20 1.90 0.20 0.90 0.10 1.00 0.10 1.10 0.10 1.25 0.15 1.30 0.10 1.50 0.10 1.55 0.10 1.40 0.15 1.70 0.15 1.60 0.20 1.90 0.20 2.00 0.20 1.70 0.20 2.50 0.20 1.10 0.15 1.15 0.15 1.30 0.15 1.40 0.15 1.50 0.15 1.00 0.15 1.10 0.15 1.30 0.15 1.40 0.15 1.50 0.15 1.70 0.15 1.80 0.15 2.40 0.15 1.00 0.15 1.10 0.15 1.30 0.15 1.40 0.15 N/A N/A N/A N/A N/A N/A N/A N/A 2,500 2,500 2,500 2,500 3,000 3,000 4,000 4,000 4,000 2,500 2,500 2,500 2,000 2,000 2,000 2,000 2,000 2,500 4,000 4,000 4,000 4,000 2,500 2,500 2,500 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 1,500 2,000 1,000 1,500 4,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 1,000 1,000 1,000 1,000 N/A N/A N/A N/A N/A N/A N/A N/A 10,000 10,000 10,000 10,000 N/A N/A 10,000 10,000 10,000 10,000 10,000 10,000 8,000 8,000 8,000 8,000 8,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 8,000 8,000 8,000 8,000 8,000 8,000 8,000 8,000 N/A 8,000 4,000 4,000 10,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 N/A 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 2,000 4,000 4,000 4,000 4,000 15,000 10,000 4,000 4,000 4,000 4,000 4,000 4,000 N/A N/A N/A N/A N/A N/A N/A 4,000 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 50,000 10,000 10,000 10,000 10,000 10,000 10,000 N/A N/A N/A N/A N/A N/A N/A 10,000 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 50,000 15,000 N/A N/A 10,000 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A This chart refers to ceramic chip thickness codes on pages 73 - 76. Note: TU suffix represents tape and reel packaging of unmarked components. Note: TM suffix represents tape and reel packaging of marked components. Cases sizes d1210 are 8mm tape with 4mm pitch and Case Sizes >1210 are 12mm tape and 8mm pitch. Thisart ch refers to ceramic chip thickness codes on pages 73-76. 78 (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 CERAMIC CHIP CAPACITORS Packaging Information Tape & Reel Packaging KEMET offers Multilayer Ceramic Chip Capacitors packaged in 8mm and 12mm plastic tape on 7" and 13" reels in accordance with EIA standard 481-1: Taping of surface mount components for automatic handling. This packaging system is compatible with all tape fed automatic pick and place systems. See page 78 for details on reeling quantities for commercial chips and page 87 for MIL-PRF-55681 chips. g handling. This packaging system is compatible with all tape fed automatic pick and place systems. See page 81 for details on reeling quantities for commercial chips and page 90 for MIL-PRF-55681 chips. Anti-Static Reel Embossed Carrier* 0402 and 0603 case sizes available on punched paper only. (R) T ME KE Chip Orientation in Pocket (except 1825 Commercial, and 1825 & 2225 Military) Embossment 8mm .30 (.315 .012") or 12mm .30 (.472 .012") 178mm (7.00") or 330mm (13.00") Anti-Static Cover Tape (.10mm (.004") Max Thickness) * Punched paper carrier used for 0402 and 0603 case size. Case Sizes 1210 are 8 mm tape with 4 mm pitch. Case Sizes >1210 are 12 mm tape with 8 mm pitch. Note: TU suffix represents tape and reel packaging of unmarked components. TM suffix represents tape and reel packaging of marked components. SURFACE MOUNT LAND DIMENSIONS - CERAMIC CHIP CAPACITORS - MM Reflow Solder Dimension 0402 0603 0805 1206 1210 1812 1825 2220 2225 CourtyardC C X X GG Y Z Z Y Z 2.14 2.78 3.30 4.50 4.50 5.90 5.90 7.00 7.00 G 0.28 0.68 0.70 1.50 1.50 2.30 2.30 3.30 3.30 X Y(ref) C(ref) 0.74 0.93 1.21 1.08 1.05 1.73 1.60 1.30 2.00 2.00 1.50 3.00 2.90 1.50 3.00 3.70 1.80 4.10 6.90 1.80 4.10 5.50 1.85 5.15 6.80 1.85 5.15 Wave Solder Z G X Y(ref) Smin Not Recommended 3.18 3.70 4.90 4.90 0.68 0.70 1.50 1.50 0.80 1.10 1.40 2.00 1.25 1.50 1.70 1.70 1.93 2.20 3.20 3.20 Not Recommended Packaging Grid Grid placement courtyard Placement Calculation Formula Z = Lmin + 2Jt + Tt G = Smax - 2Jh -Th X = Wmin + 2Js + Ts Tt, Th, Ts = Combined tolerances (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 93 TANTALUM, CERAMIC AND ALUMINUM CHIP CAPACITORS Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg Minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0.1 Newton to 1.0 Newton (10g to 100g) 12 mm 0.1 Newton to 1.3 Newton (10g to 130g) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 10 mm/minute. 3. Reel Sizes: Molded tantalum capacitors are available on either 180 mm (7") reels (standard) or 330 mm (13") reels (with C-7280). Note that 13" reels are preferred. 4. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA-556. Embossed Carrier Tape Configuration: Figure 1 Table 1 -- EMBOSSED TAPE DIMENSIONS (Metric will govern) Constant Dimensions -- Millimeters (Inches) Tape Size 8 mm and 12 mm D0 E 1.5 1.75 0.10 +0.10 -0.0 (0.059 (0.069 0.004) +0.004, -0.0) P0 P2 T Max T1 Max 4.0 0.10 2.0 0.05 0.600 0.100 (0.157 0.004) (0.079 0.002) (0.024) (0.004) Variable Dimensions -- Millimeters (Inches) Tape Size Pitch B1 Max. Note 1 D1 Min. Note 2 F P1 R Min. Note 3 T2 Max W 8 mm Single (4 mm) 4.4 1.0 3.5 0.05 4.0 0.10 25.0 2.5 8.0 0.30 (.315 0.012) 12 mm Double (8 mm) (0.173) (0.039) (0.138 0.002) (0.157 0.004) (0.984) (0.098) 8.2 (0.323) 1.5 5.5 0.05 (0.059) (0.217 0.002) 8.0 0.10 30.0 (0.315 0.004) (1.181) 4.6 12.0 0.30 (0.181) (0.472 0.012) A0B0K0 Note 4 NOTES 1. B1 dimension is a reference dimension for tape feeder clearance only. 2. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 3. Tape with components shall pass around radius "R" without damage (see sketch A). The minimum trailer length (Fig. 2) may require additional length to provide R min. for 12 mm embossed tape for reels with hub diameters approaching N min. (Table 2) 4. The cavity defined by A0, B0, and K0 shall be configured to surround the part with sufficient clearance such that the chip does not protrude beyond the sealing plane of the cover tape, the chip can be removed from the cavity in a vertical direction without mechanical restriction, rotation of the chip is limited to 20 degrees maximum in all 3 planes, and lateral movement of the chip is restricted to 0.5 mm maximum in the pocket (not applicable to vertical clearance.) 94 (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 TANTALUM, CERAMIC AND ALUMINUM CHIP CAPACITORS Packaging Information Embossed Carrier Tape Configuration (cont.) 20 Sketch D: Tape Camber (Top View) 1mm (0.039) Max. 1mm (0.039) Max. 250mm (9.843) Allowable camber to be 1 mm/250 mm. 400mm (15.75) Min. Figure 2: Tape Leader & Trailer Dimensions (Metric Dimensions Will Govern) Packaging Figure 3: Reel Dimensions (Metric Dimensions will govern) Table 2 - REEL DIMENSIONS (Metric will govern) Tape Size 8 mm A Max 330.0 (12.992) B* Min 1.5 (0.059) C 13.0 0.20 (0.512 0.008) D* Min 20.2 (0.795) 12 mm 330.0 (12.992) 1.5 (0.059) 13.0 0.20 (0.512 0.008) 20.2 (0.795) N Min 50.0 (1.969) See Note 3 Table 1 W1 8.4 +1.5, -0.0 (0.331 +0.059, -0.0) 12.4 +2.0, -0.0 (0.488 +0.078, -0.0) W2 Max 14.4 (0.567) 18.4 (0.724) (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 W3 7.9 Min (0.311) 10.9 Max (0.429) 11.9 Min (0.469) 15.4 Max (0.606) 95 CERAMIC CHIP CAPACITORS Packaging Information Punched Carrier (Paper Tape) Configuration (Ceramic Chips Only): 10 pitches cumulative tolerance on tape 0.2 (0.008) P0 T P2 D0 E Top Tape Cover Bottom Tape Cover A0 F W B0 G2 T1 P1 User Direction of Feed Center lines of cavity Max. Cavity Size See Note 1 Table 1 Table 1: 8 & 12mm Punched Tape (Metric Dimensions Will Govern) Constant Dimensions - Millimeters (Inches) Tape Size D0 P0 E T1 P2 G1 G2 R Min. 8mm 1.5 1.75 0.10 4.0 0.10 2.0 0.05 0.10 0.75 0.75 25 (.984) and +0.10, -0.0 (.004) (.030) (.030) See Note 2 12mm (.059 (.069 0.004) (.157 0.004) (.079 0.002) Max. Min. Min. Table 1 +0.004, -0.0) Table 1: 8 & 12mm Punched Tape (Metric Dimensions Will Govern) Variable Dimensions - Millimeters (Inches) Tape Size 8mm 1/2 Pitch P1 2.0 0.10 (.079 .004) 3.5 0.05 See Requirements Section 3.3 (d) (.138 .002) 8mm 4.0 0.10 (0.157 .004) 12mm 4.0 0.10 (0.157 .004) A0B0 W F 5.5 0.05 12mm 8.0 0.10 (.217 .002) Double (0.315 .004) Pitch 8.0 0.3 (.315 0.012) See Note 1 Table 1 12.0 0.3 T 1.1mm (.043) Max. for Paper Base Tape and 1.6mm (.063) Max. for NonPaper Base Compositions. See Note 3. (.472 .012) Note: 1. A0, B0 and T determined by the maximum dimensions to the ends of the terminals extending from the body and/or the body dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the cavity (A0, B0 and T) must be within 0.05mm (.002) minimum and 0.50mm (.020) maximum. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see sketches A and B). 2. Tape with components shall pass around radius "R" without damage. 3. KEMET nominal thicknesses are: 0402 = 0.6mm and all others 0.95mm minimum. Sketch A: Bending Radius See Note 2 Table 1 Sketch B: Max. Component Rotation - Front Cross Sectional View R (Min.) 20 96 Sketch C: Component Rotation - Top View Maximum 20 component rotation. Typical component center line (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 CERAMIC CHIP CAPACITORS Packaging Information Bulk Cassette Packaging (Ceramic Chips only) Table 2 - Capacitance Values Available In Bulk Cassette Packaging 6.8 0.1 8.8 0.1 12.0 0.1 (Meets Dimensional Requirements IEC-286-6 and EIAJ 7201) 53.3* 2.0 31.5 0.2 0 3.0 0.1 0 0 0.1 0.2 0 0402 All All All All 0603 All All All All 0805 C0G 200 100 50 109 109 109 181 331 102 X7R 200 100 50 25 16 221 221 221 221 221 392 103 273 104 104 Y5V 25 16 104 104 224 224 19.0* 1.5 Unit: mm * Reference 36 00.2 10* Min. Max. Case Cap Cap Size Dielectric Voltage Value Value 5.0* 110 0.7 Table 1 - Capacitor Dimensions for Bulk Cassette Packaging - Millimeters Metric Size Code EIA Size Code 1005 1608 2012 0402 0603 0805 Length L Width W Thickness Bandwidth T B 1.0 0.05 0.5 0.05 1.6 0.07 0.8 0.07 2.0 0.10 1.25 0.10 0.5 .05 0.8 .07 0.6 .10 0.2 to 0.4 0.2 to 0.5 0.5 to 0.75 Minimum Separation S Number of Pcs/Cassette 0.3 0.7 0.75 50,000 15,000 10,000 Terminations: KEMET nickel barrier layer with a tin overplate. CAPACITOR MARKING TABLE (Marking Optional - Not Available for 0402 Size or Y5V Dielectric) 9 0 1 2 3 4 5 6 7 A B C D E F G H J K L M N P Q R S T U V W X Y Z a b d e f m n t y 0.10 0.11 0.12 0.13 0.15 0.16 0.18 0.20 0.22 0.24 0.27 0.30 0.33 0.36 0.39 0.43 0.47 0.51 0.56 0.62 0.68 0.75 0.82 0.91 0.25 0.35 0.40 0.45 0.50 0.60 0.70 0.80 0.90 1.0 1.1 1.2 1.3 1.5 1.6 1.8 2.0 2.2 2.4 2.7 3.0 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 2.5 3.5 4.0 4.5 5.0 6.0 7.0 8.0 9.0 10 11 12 13 15 16 18 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82 91 25 35 40 45 50 60 70 80 90 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 250 350 400 450 500 600 700 800 900 1000 1100 1200 1300 1500 1600 1800 2000 2200 2400 2700 3000 3300 3600 3900 4300 4700 5100 5600 6200 6800 7500 8200 9100 2500 3500 4000 4500 5000 6000 7000 8000 9000 10,000 11,000 12,000 13,000 15,000 16,000 18,000 20,000 22,000 24,000 27,000 30,000 33,000 36,000 39,000 43,000 47,000 51,000 56,000 62,000 68,000 75,000 82,000 91,000 25,000 35,000 40,000 45,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 150,000 160,000 180,000 200,000 220,000 240,000 270,000 300,000 330,000 360,000 390,000 430,000 470,000 510,000 560,000 620,000 680,000 750,000 820,000 910,000 250,000 350,000 400,000 450,000 500,000 600,000 700,000 800,000 900,000 1,000,000 1,100,000 1,200,000 1,300,000 1,500,000 1,600,000 1,800,000 2,000,000 2,200,000 2,400,000 2,700,000 3,000,000 3,300,000 3,600,000 3,900,000 4,300,000 4,700,000 5,100,000 5,600,000 6,200,000 6,800,000 7,500,000 8,200,000 9,100,000 2,500,000 3,500,000 4,000,000 4,500,000 5,000,000 6,000,000 7,000,000 8,000,000 9,000,000 10,000,000 11,000,000 12,000,000 13,000,000 15,000,000 16,000,000 18,000,000 20,000,000 22,000,000 24,000,000 27,000,000 30,000,000 33,000,000 36,000,000 39,000,000 43,000,000 47,000,000 51,000,000 56,000,000 62,000,000 68,000,000 75,000,000 82,000,000 91,000,000 25,000,000 35,000,000 40,000,000 45,000,000 50,000,000 60,000,000 70,000,000 80,000,000 90,000,000 Laser marking is available as an extra-cost option for most KEMET ceramic chips. Such marking is two sided, and includes a K to identify KEMET, followed by two characters (per EIA-198 - see table below) to identify the capacitance value. Note that marking is not available for size 0402 nor for any Y5V chip. In addition, the 0603 marking option is limited to the K only. KA3 Example shown is 1,000 pF capacitor. (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 Packaging Capacitance (pF) For Various Numeral Identifiers Numeral Alpha Character 97 KEMET Electronics - KEMET Ceramic P/N Suffixes - Marking & Packaging Page 1 of 2 CONTACT US | CUSTOMER SERVICE Search here for KEMET PN, Competitor PN, Partial PN, or Part Description Search here for General Keywords, Part Series, or Corporate Information KE Home Search FAQs Technical Articles Created: 04/17/2000 Updated: 08/28/2009 Contact Us Help Product: Ceramic Categories: Labeling, Packaging, Part Markings, Part Number KEMET Ceramic P/N Suffixes - Marking & Packaging Description : KEMET Ceramic P/N Suffixes - Marking & Packaging Answer : KEMET ceramic chips are available marked or unmarked (preferred) in several packaging styles. These ordering details are included as suffixes to the KEMET 14 digit part number, and will be used during the order entry process by KEMET sales personnel and distributors. (Notice that ordering a KEMET part number without a suffix will result in shipment of unmarked chips loose packed in a bag - so be sure to use a suffix if other packaging is needed.) To speed up the ordering process, we use "shortcut" suffixes for the most common ordering modes. The most popular shortcut ordering suffix is "TU", which indicates unmarked chips, in labelled 7" tape & reel packaging. Alternatively, ordering suffix "TM" indicates marked chips, in labelled 7" reels. However, remember that marked chips are less likely to be in stock, and will have a cost premium associated with marking. Details on marking appear in our catalog, available on the website. Note that all 0402 chips and all Y5V chips are not available marked. Other special ordering suffixes also exist, covering options such as 13" reels, bulk cassette, and bulk in bag packaging. In addition, special customer requirements will also be included in custom ordering suffixes, up to 2 groups of 4 numerical digits each. When the capacitors are shipped, the labels will be printed with the 14 digit KEMET part number, plus the numerical suffixes ordered (or corresponding to the shortcut suffixes). These will include one or more 4 digit numerical suffix(es), which indicate the exact mode of marking and packaging. These will be based on the information given to KEMET sales at the time of order entry, and and are detailed in the following table. (Note - to improve delivery, marked chips may occasionally be supplied when unmarked are acceptable.) CATEGORY DESCRIPTION Unmarked Marking Required (Marking not available for any 0402 or Y5V chips) Standard Reeling 7" Plastic Tape 0805 - 2225 (0402, 0603 & 0805 thickness DB, DC & DD are reeled only on paper) 7800 (same as "TU") 7025 (same as "TM") Standard Reeling 7" Paper Tape 0402 & 0603 7867(same as "TU") 7013(same as "TM") Special Reeling 13" Plastic Tape 0805 - 2225 (0402, 0603 & 0805 thickness DB, DC & DD are reeled only on paper) 7210 7215 Special Reeling 7" Paper Tape 0805 (0.78 mm thickness selected values only) 7867 & 9239 7013 & 9239 Special Reeling 7" Paper Tape 1206 - 1210 (selected values only) 7867 7013 Special Reeling 13" Paper Tape 0402 & 0603 7411 7040 Special Reeling 13" Paper Tape 0805 (0.78 mm thickness selected values only) 7411 & 9239 7040 & 9239 Special Reeling 13" Paper Tape 1206 - 1210 (selected values only) 7411 7040 Special Packaging Bulk Cassette for 0402, 0603 & 0805. 0402's are never marked. Use ONLY with special 0.6 mm 0805. 9028 9028 & 3325 Special Packaging Loose Chips in Plastic Bags 0603 - 2225 No Suffix 3325 Technical Papers featured at CARTS Europe 2007: Aluminium Electrolytic Capacitors' performance in Very High Ripple Current and Temperature Applications Reliability and Critical Applications of Tantalum Capacitors Click here for a full listing of our Technical Papers BME C0G MLCCs: The High Capacitance Class-I Solution Soldering of SMD Film Capacitors in Practical Lead Free Processes D-Pack 3D Interposer Decoupling System Study of MnO2 Coverage on Ta Capacitors with High CV Powders ESR Stabilization of Ta Capacitors for Automotive Applications in Severe Environmental Conditions The Battle for Maximum Volumetric Efficiency - Part 1: When Technologies Compete, Customers Win Improved Ripple Current Capability with Facedown Terminations The Battle for Maximum Volumetric Efficiency - Part 2: Advancements in Solid Electrolyte Capacitors http://www.kemet.com/kemet/web/homepage/kfbk3.nsf/vaFeedbackFAQ/3B46726C01571... 8/28/2009 CERAMIC CHIP/CAPACITORS Tin Lead L Termination FEATURES KEMET's line of Tin/Lead termination commercial MLCC surface mount capacitors are designed to meet the needs of the commercial, high reliability, and military customer applications where Tin/Lead plating is required. KEMET's Tin/Lead electroplating process is designed to meet a 5% minimum lead content in the termination of the component. As the bulk of the electronics industry marches to RoHS compliance it is important that KEMET provide the Tin/Lead terminated products for our valued high reliability and military customers. KEMET Tin/Lead MLCC surface mount capacitors are available in standard EIA case sizes from 0402 to 2225 and standard KEMET Tiin/Lead MLCC surface mount capacitors are available in standard EIA to case sizes 0402 to 2225 and standard capacitance values in X7R and C0G dielectrics. Voltage ratings range from 6.3V 200V. Tofrom order the Tin/Lead terminations th capacitance values X7R, X5R, C0G dielectrics. Voltage ratings range from 6.3V to 200V. To order themount Tin/Lead terminaindicate an "L" in thein14 digit of the part number. To request the L Series termination for other surface product lines (Open th tions an "L" in the 14etc.) digit part number. For additional and voltage contact the facMode,indicate High Voltage, Arrays, or of forthe additional dielectrics and higherdielectrics voltage ratings, pleaseratings contactplease the factory or local Sales tory or local Sales personnel. representative. CAPACITOR OUTLINE DRAWINGS W T L Sn/Pb PLATE B NICKEL PLATE S ELECTRODES CONDUCTIVE METALLIZATION DIMENSIONS--MILLIMETERS AND (INCHES) METRIC SIZE CODE L - LENGTH W - WIDTH 0201* 0603 0.6 (.024) .03 (.001) 0.3 (.012) .03 (.001) 0.15 (.006) .05 (.002) N/A 0402* 1005 1.0 (.04) .05 (.002) 0.5 (.02) .05 (.002) 0.20 (.008) -.40 (.016) 0.3 (.012) B - BANDWIDTH 0603 1608 1.6 (.063) .15 (.006) 0.8 (.032) .15 (.006) 0.35 (.014) .15 (.006) 0.7 (.028) 0805* 2012 2.0 (.079) .20 (.008) 1.25 (.049) .20 (.008) 0.50 (.02) .25 (.010) 0.75 (.030) 1206* 3216 3.2 (.126) .20 (.008) 1.6 (.063) .20 (.008) 0.50 (.02) .25 (.010) N/A 1210* 3225 3.2 (.126) .20 (.008) 2.5 (.098) .20 (.008) 1808 4520 4.5 (.177) .30 (.012) 2.0 (.079) .20 (.008) See page 78 for thickness dimensions. 0.50 (.02) .25 (.010) N/A 0.60 (.024) .35 (.014) N/A N/A 1812 4532 4.5 (.177) .30 (.012) 3.2 (.126) .30 (.012) 0.60 (.024) .35 (.014) 1825* 4564 4.5 (.177) .30 (.012) 6.4 (.252) .40 (.016) 0.60 (.024) .35 (.014) N/A 2220 5650 5.6 (.220) .40 (.016) 5.0 (.197) .40 (.016) 0.60 (.024) .35 (.014) N/A 2225 5664 5.6 (.220) .40 (.016) 6.3 (.248) .40 (.016) 0.60 (.024) .35 (.014) N/A MOUNTING TECHNIQUE Solder Reflow Solder Wave + or Solder Reflow Solder Reflow * Note: Indicates EIA Preferred Case Sizes (Tightened tolerances apply for 0402, 0603, and 0805 packaged in bulk cassette, see page 96.) For extended value 1210 case size - solder reflow only. CAPACITOR ORDERING INFORMATION (Standard Chips - For Military see page 87) C 0805 C 103 K 5 R A L* CERAMIC SIZE CODE SPECIFICATION C - Standard CAPACITANCE CODE Expressed in Picofarads (pF) First two digits represent significant figures. Third digit specifies number of zeros. (Use 9 for 1.0 through 9.9pF. Use 8 for 0.5 through 0.99pF) (Example: 2.2pF = 229 or 0.50 pF = 508) CAPACITANCE TOLERANCE B - 0.10pF J - 5% C - 0.25pF K - 10% D - 0.5pF M - 20% F - 1% G - 2% * Part Number Example: C0805C103K5RAL END METALLIZATION L - SnPb plated nickel barrier (SnPb 5% minimum) FAILURE RATE LEVEL A- Not Applicable TEMPERATURE CHARACTERISTIC Designated by Capacitance Change Over Temperature Range G - C0G (NP0) (30 PPM/C) R - X7R (15%) (-55C + 125C) P - X5R (15%) (-55C + 85C) VOLTAGE 1 - 100V 3 - 25V 2 - 200V 4 - 16V 5 - 50V 8 - 10V 9 - 6.3V 6 - 35V (14 digits - no spaces) Refer to pages 73-76 for NP0/C0G, X7R and X5R dielectric capacitance ranges available. (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 77 Ceramic Surface Mount T THICKNESS S SEPARATION minimum EIA SIZE CODE CERAMIC CHIP CAPACITORS Thickness Code Reference Chart Packaging Quantity Based on Finished Chip Thickness Specifications Thickness Code Chip Size Chip Thickness Range (mm) Qty per Reel 7" Plastic Qty per Reel 13" Plastic Qty per Reel 7" Paper Qty per Reel 13" Paper Qty per Bulk Cassette AA BB CB CC CD DB DC DD DE DF DG DH DJ DK DL EB EC ED EE EF EG EH EJ EK EL EM EN FB FC FD FE FF FG FH FJ FK FL FM FN FO FP FQ FR FS FT LD GB GC GD GE GF GG GH GJ GK GL GM GN GO HB HC HD HE HF JB JC JD JE JF JG JH JO KB KC KD KE 0201 0402 0603 0603 0603 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 1206 1206 1206 1206 1206 1206 1206 1206 1206 1206 1206 1206 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1808 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1825 1825 1825 1825 1825 2220 2220 2220 2220 2220 2220 2220 2220 2225 2225 2225 2225 0.30 0.03 0.50 0.05 0.80 0.07 0.80 0.10 0.80 0.15 0.60 0.10 0.78 0.10 0.90 0.10 1.00 0.10 1.10 0.10 1.25 0.15 1.25 0.20 1.25 0.20 1.25 0.15 0.95 0.10 0.78 0.10 0.90 0.10 1.00 0.10 1.10 0.10 1.20 0.15 1.60 0.15 1.60 0.20 1.70 0.20 0.80 0.10 1.15 0.15 1.25 0.15 0.95 0.10 0.78 0.10 0.90 0.10 0.95 0.10 1.00 0.10 1.10 0.10 1.25 0.15 1.55 0.15 1.85 0.20 2.10 0.20 1.40 0.15 1.70 0.20 1.85 0.20 1.50 0.20 1.60 0.20 2.50 0.22 2.25 0.20 2.50 0.20 1.90 0.20 0.90 0.10 1.00 0.10 1.10 0.10 1.25 0.15 1.30 0.10 1.50 0.10 1.55 0.10 1.40 0.15 1.70 0.15 1.60 0.20 1.90 0.20 2.00 0.20 1.70 0.20 2.50 0.20 1.10 0.15 1.15 0.15 1.30 0.15 1.40 0.15 1.50 0.15 1.00 0.15 1.10 0.15 1.30 0.15 1.40 0.15 1.50 0.15 1.70 0.15 1.80 0.15 2.40 0.15 1.00 0.15 1.10 0.15 1.30 0.15 1.40 0.15 N/A N/A N/A N/A N/A N/A N/A N/A 2,500 2,500 2,500 2,500 3,000 3,000 4,000 4,000 4,000 2,500 2,500 2,500 2,000 2,000 2,000 2,000 2,000 2,500 4,000 4,000 4,000 4,000 2,500 2,500 2,500 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 1,500 2,000 1,000 1,500 4,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 1,000 1,000 1,000 1,000 N/A N/A N/A N/A N/A N/A N/A N/A 10,000 10,000 10,000 10,000 N/A N/A 10,000 10,000 10,000 10,000 10,000 10,000 8,000 8,000 8,000 8,000 8,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 8,000 8,000 8,000 8,000 8,000 8,000 8,000 8,000 N/A 8,000 4,000 4,000 10,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 N/A 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 2,000 4,000 4,000 4,000 4,000 15,000 10,000 4,000 4,000 4,000 4,000 4,000 4,000 N/A N/A N/A N/A N/A N/A N/A 4,000 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 50,000 10,000 10,000 10,000 10,000 10,000 10,000 N/A N/A N/A N/A N/A N/A N/A 10,000 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 50,000 15,000 N/A N/A 10,000 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A This chart refers to ceramic chip thickness codes on pages 73 - 76. Note: TU suffix represents tape and reel packaging of unmarked components. Note: TM suffix represents tape and reel packaging of marked components. Cases sizes d1210 are 8mm tape with 4mm pitch and Case Sizes >1210 are 12mm tape and 8mm pitch. Thisart ch refers to ceramic chip thickness codes on pages 73-76. 78 (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 CERAMIC CHIP CAPACITORS Packaging Information Tape & Reel Packaging KEMET offers Multilayer Ceramic Chip Capacitors packaged in 8mm and 12mm plastic tape on 7" and 13" reels in accordance with EIA standard 481-1: Taping of surface mount components for automatic handling. This packaging system is compatible with all tape fed automatic pick and place systems. See page 78 for details on reeling quantities for commercial chips and page 87 for MIL-PRF-55681 chips. g handling. This packaging system is compatible with all tape fed automatic pick and place systems. See page 81 for details on reeling quantities for commercial chips and page 90 for MIL-PRF-55681 chips. Anti-Static Reel Embossed Carrier* 0402 and 0603 case sizes available on punched paper only. (R) T ME KE Chip Orientation in Pocket (except 1825 Commercial, and 1825 & 2225 Military) Embossment 8mm .30 (.315 .012") or 12mm .30 (.472 .012") 178mm (7.00") or 330mm (13.00") Anti-Static Cover Tape (.10mm (.004") Max Thickness) * Punched paper carrier used for 0402 and 0603 case size. Case Sizes 1210 are 8 mm tape with 4 mm pitch. Case Sizes >1210 are 12 mm tape with 8 mm pitch. Note: TU suffix represents tape and reel packaging of unmarked components. TM suffix represents tape and reel packaging of marked components. SURFACE MOUNT LAND DIMENSIONS - CERAMIC CHIP CAPACITORS - MM Reflow Solder Dimension 0402 0603 0805 1206 1210 1812 1825 2220 2225 CourtyardC C X X GG Y Z Z Y Z 2.14 2.78 3.30 4.50 4.50 5.90 5.90 7.00 7.00 G 0.28 0.68 0.70 1.50 1.50 2.30 2.30 3.30 3.30 X Y(ref) C(ref) 0.74 0.93 1.21 1.08 1.05 1.73 1.60 1.30 2.00 2.00 1.50 3.00 2.90 1.50 3.00 3.70 1.80 4.10 6.90 1.80 4.10 5.50 1.85 5.15 6.80 1.85 5.15 Wave Solder Z G X Y(ref) Smin Not Recommended 3.18 3.70 4.90 4.90 0.68 0.70 1.50 1.50 0.80 1.10 1.40 2.00 1.25 1.50 1.70 1.70 1.93 2.20 3.20 3.20 Not Recommended Packaging Grid Grid placement courtyard Placement Calculation Formula Z = Lmin + 2Jt + Tt G = Smax - 2Jh -Th X = Wmin + 2Js + Ts Tt, Th, Ts = Combined tolerances (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 93 TANTALUM, CERAMIC AND ALUMINUM CHIP CAPACITORS Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg Minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0.1 Newton to 1.0 Newton (10g to 100g) 12 mm 0.1 Newton to 1.3 Newton (10g to 130g) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 10 mm/minute. 3. Reel Sizes: Molded tantalum capacitors are available on either 180 mm (7") reels (standard) or 330 mm (13") reels (with C-7280). Note that 13" reels are preferred. 4. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA-556. Embossed Carrier Tape Configuration: Figure 1 Table 1 -- EMBOSSED TAPE DIMENSIONS (Metric will govern) Constant Dimensions -- Millimeters (Inches) Tape Size 8 mm and 12 mm D0 E 1.5 1.75 0.10 +0.10 -0.0 (0.059 (0.069 0.004) +0.004, -0.0) P0 P2 T Max T1 Max 4.0 0.10 2.0 0.05 0.600 0.100 (0.157 0.004) (0.079 0.002) (0.024) (0.004) Variable Dimensions -- Millimeters (Inches) Tape Size Pitch B1 Max. Note 1 D1 Min. Note 2 F P1 R Min. Note 3 T2 Max W 8 mm Single (4 mm) 4.4 1.0 3.5 0.05 4.0 0.10 25.0 2.5 8.0 0.30 (.315 0.012) 12 mm Double (8 mm) (0.173) (0.039) (0.138 0.002) (0.157 0.004) (0.984) (0.098) 8.2 (0.323) 1.5 5.5 0.05 (0.059) (0.217 0.002) 8.0 0.10 30.0 (0.315 0.004) (1.181) 4.6 12.0 0.30 (0.181) (0.472 0.012) A0B0K0 Note 4 NOTES 1. B1 dimension is a reference dimension for tape feeder clearance only. 2. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 3. Tape with components shall pass around radius "R" without damage (see sketch A). The minimum trailer length (Fig. 2) may require additional length to provide R min. for 12 mm embossed tape for reels with hub diameters approaching N min. (Table 2) 4. The cavity defined by A0, B0, and K0 shall be configured to surround the part with sufficient clearance such that the chip does not protrude beyond the sealing plane of the cover tape, the chip can be removed from the cavity in a vertical direction without mechanical restriction, rotation of the chip is limited to 20 degrees maximum in all 3 planes, and lateral movement of the chip is restricted to 0.5 mm maximum in the pocket (not applicable to vertical clearance.) 94 (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 TANTALUM, CERAMIC AND ALUMINUM CHIP CAPACITORS Packaging Information Embossed Carrier Tape Configuration (cont.) 20 Sketch D: Tape Camber (Top View) 1mm (0.039) Max. 1mm (0.039) Max. 250mm (9.843) Allowable camber to be 1 mm/250 mm. 400mm (15.75) Min. Figure 2: Tape Leader & Trailer Dimensions (Metric Dimensions Will Govern) Packaging Figure 3: Reel Dimensions (Metric Dimensions will govern) Table 2 - REEL DIMENSIONS (Metric will govern) Tape Size 8 mm A Max 330.0 (12.992) B* Min 1.5 (0.059) C 13.0 0.20 (0.512 0.008) D* Min 20.2 (0.795) 12 mm 330.0 (12.992) 1.5 (0.059) 13.0 0.20 (0.512 0.008) 20.2 (0.795) N Min 50.0 (1.969) See Note 3 Table 1 W1 8.4 +1.5, -0.0 (0.331 +0.059, -0.0) 12.4 +2.0, -0.0 (0.488 +0.078, -0.0) W2 Max 14.4 (0.567) 18.4 (0.724) (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 W3 7.9 Min (0.311) 10.9 Max (0.429) 11.9 Min (0.469) 15.4 Max (0.606) 95 CERAMIC CHIP CAPACITORS Packaging Information Punched Carrier (Paper Tape) Configuration (Ceramic Chips Only): 10 pitches cumulative tolerance on tape 0.2 (0.008) P0 T P2 D0 E Top Tape Cover Bottom Tape Cover A0 F W B0 G2 T1 P1 User Direction of Feed Center lines of cavity Max. Cavity Size See Note 1 Table 1 Table 1: 8 & 12mm Punched Tape (Metric Dimensions Will Govern) Constant Dimensions - Millimeters (Inches) Tape Size D0 P0 E T1 P2 G1 G2 R Min. 8mm 1.5 1.75 0.10 4.0 0.10 2.0 0.05 0.10 0.75 0.75 25 (.984) and +0.10, -0.0 (.004) (.030) (.030) See Note 2 12mm (.059 (.069 0.004) (.157 0.004) (.079 0.002) Max. Min. Min. Table 1 +0.004, -0.0) Table 1: 8 & 12mm Punched Tape (Metric Dimensions Will Govern) Variable Dimensions - Millimeters (Inches) Tape Size 8mm 1/2 Pitch P1 2.0 0.10 (.079 .004) 3.5 0.05 See Requirements Section 3.3 (d) (.138 .002) 8mm 4.0 0.10 (0.157 .004) 12mm 4.0 0.10 (0.157 .004) A0B0 W F 5.5 0.05 12mm 8.0 0.10 (.217 .002) Double (0.315 .004) Pitch 8.0 0.3 (.315 0.012) See Note 1 Table 1 12.0 0.3 T 1.1mm (.043) Max. for Paper Base Tape and 1.6mm (.063) Max. for NonPaper Base Compositions. See Note 3. (.472 .012) Note: 1. A0, B0 and T determined by the maximum dimensions to the ends of the terminals extending from the body and/or the body dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the cavity (A0, B0 and T) must be within 0.05mm (.002) minimum and 0.50mm (.020) maximum. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see sketches A and B). 2. Tape with components shall pass around radius "R" without damage. 3. KEMET nominal thicknesses are: 0402 = 0.6mm and all others 0.95mm minimum. Sketch A: Bending Radius See Note 2 Table 1 Sketch B: Max. Component Rotation - Front Cross Sectional View R (Min.) 20 96 Sketch C: Component Rotation - Top View Maximum 20 component rotation. Typical component center line (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 CERAMIC CHIP CAPACITORS Packaging Information Bulk Cassette Packaging (Ceramic Chips only) Table 2 - Capacitance Values Available In Bulk Cassette Packaging 6.8 0.1 8.8 0.1 12.0 0.1 (Meets Dimensional Requirements IEC-286-6 and EIAJ 7201) 53.3* 2.0 31.5 0.2 0 3.0 0.1 0 0 0.1 0.2 0 0402 All All All All 0603 All All All All 0805 C0G 200 100 50 109 109 109 181 331 102 X7R 200 100 50 25 16 221 221 221 221 221 392 103 273 104 104 Y5V 25 16 104 104 224 224 19.0* 1.5 Unit: mm * Reference 36 00.2 10* Min. Max. Case Cap Cap Size Dielectric Voltage Value Value 5.0* 110 0.7 Table 1 - Capacitor Dimensions for Bulk Cassette Packaging - Millimeters Metric Size Code EIA Size Code 1005 1608 2012 0402 0603 0805 Length L Width W Thickness Bandwidth T B 1.0 0.05 0.5 0.05 1.6 0.07 0.8 0.07 2.0 0.10 1.25 0.10 0.5 .05 0.8 .07 0.6 .10 0.2 to 0.4 0.2 to 0.5 0.5 to 0.75 Minimum Separation S Number of Pcs/Cassette 0.3 0.7 0.75 50,000 15,000 10,000 Terminations: KEMET nickel barrier layer with a tin overplate. CAPACITOR MARKING TABLE (Marking Optional - Not Available for 0402 Size or Y5V Dielectric) 9 0 1 2 3 4 5 6 7 A B C D E F G H J K L M N P Q R S T U V W X Y Z a b d e f m n t y 0.10 0.11 0.12 0.13 0.15 0.16 0.18 0.20 0.22 0.24 0.27 0.30 0.33 0.36 0.39 0.43 0.47 0.51 0.56 0.62 0.68 0.75 0.82 0.91 0.25 0.35 0.40 0.45 0.50 0.60 0.70 0.80 0.90 1.0 1.1 1.2 1.3 1.5 1.6 1.8 2.0 2.2 2.4 2.7 3.0 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 2.5 3.5 4.0 4.5 5.0 6.0 7.0 8.0 9.0 10 11 12 13 15 16 18 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82 91 25 35 40 45 50 60 70 80 90 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 250 350 400 450 500 600 700 800 900 1000 1100 1200 1300 1500 1600 1800 2000 2200 2400 2700 3000 3300 3600 3900 4300 4700 5100 5600 6200 6800 7500 8200 9100 2500 3500 4000 4500 5000 6000 7000 8000 9000 10,000 11,000 12,000 13,000 15,000 16,000 18,000 20,000 22,000 24,000 27,000 30,000 33,000 36,000 39,000 43,000 47,000 51,000 56,000 62,000 68,000 75,000 82,000 91,000 25,000 35,000 40,000 45,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 150,000 160,000 180,000 200,000 220,000 240,000 270,000 300,000 330,000 360,000 390,000 430,000 470,000 510,000 560,000 620,000 680,000 750,000 820,000 910,000 250,000 350,000 400,000 450,000 500,000 600,000 700,000 800,000 900,000 1,000,000 1,100,000 1,200,000 1,300,000 1,500,000 1,600,000 1,800,000 2,000,000 2,200,000 2,400,000 2,700,000 3,000,000 3,300,000 3,600,000 3,900,000 4,300,000 4,700,000 5,100,000 5,600,000 6,200,000 6,800,000 7,500,000 8,200,000 9,100,000 2,500,000 3,500,000 4,000,000 4,500,000 5,000,000 6,000,000 7,000,000 8,000,000 9,000,000 10,000,000 11,000,000 12,000,000 13,000,000 15,000,000 16,000,000 18,000,000 20,000,000 22,000,000 24,000,000 27,000,000 30,000,000 33,000,000 36,000,000 39,000,000 43,000,000 47,000,000 51,000,000 56,000,000 62,000,000 68,000,000 75,000,000 82,000,000 91,000,000 25,000,000 35,000,000 40,000,000 45,000,000 50,000,000 60,000,000 70,000,000 80,000,000 90,000,000 Laser marking is available as an extra-cost option for most KEMET ceramic chips. Such marking is two sided, and includes a K to identify KEMET, followed by two characters (per EIA-198 - see table below) to identify the capacitance value. Note that marking is not available for size 0402 nor for any Y5V chip. In addition, the 0603 marking option is limited to the K only. KA3 Example shown is 1,000 pF capacitor. (c)KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 Packaging Capacitance (pF) For Various Numeral Identifiers Numeral Alpha Character 97