MIC23060 Sequenced Power Management IC with HyperLight LoadTM DC/DC and Dual Input LDOTM General Description Features The MIC23060 is a highly efficient power management IC integrating a high frequency DC/DC converter with HyperLight LoadTM mode and a low input voltage capable LDO. The MIC23060 offers two output voltages at very high efficiency on both outputs while maintaining a low total system cost. The MIC23060 also provides sequencing of the two outputs in every potential combination of turn-on and turnoff sequencing by connecting two pins either high or low, and using a single GPIO to enable and disable the device. The LDO is designed both to post regulate from the output of the DC/DC converter for high system efficiency, and/or power directly from the battery. For sequences where the LDO is enabled prior to the DC/DC output, the LDO is first powered by the input voltage (typically the battery source) and then after the DCDC soft start is complete, seamlessly transition LDO input power to draw from the output of the DC/DC converter for higher efficiency operation through post-regulation. The DC/DC converter in the MIC23060 is a HyperLight LoadTM converter with very high efficiency at light load and at full operating current, maintaining high efficiency across all operating modes in portable electronics. The MIC23060 is a Cap design, operating with small ceramic output capacitors and tiny inductors for stability, reducing required board space and component cost and is available in the tiny 2.5mm x 2.5mm Thin MLF(R) package. Data sheets and support documentation can be found on Micrel's web site at www.micrel.com. * 2.7V to 5.5V supply voltage range * Tiny 12-pin 2.5mm x 2.5mm Thin MLF(R) package * Integrated sequencing - Dual Input LDOTM can turn-on prior to DC/DC converter and automatically switch to post regulation from the DC/DC converter after it starts - Power for LDO from input during start-up - Adjustable delay time between outputs * Zero-current off mode * Current-limit and thermal shutdown protection HyperLight LoadTM DC/DC Converter * Up to 600mA output current in PWM mode (shared between switcher and linear LDO regulator outputs) * 4MHz frequency in continuous PWM mode * Tiny 2.2H inductor, 4.7F capacitor * 85% Efficiency at 1mA output current * >90% peak efficiency * Low output voltage ripple across all loads LDO Regulator * Low Input voltage LDO regulator * Stable with ceramic output capacitors * Regulates from the output of the DC/DC converter * 300mA output current capability * High Accuracy: 3% over temperature * High PSRR: greater than 60dB * Very low quiescent current: 16A Applications * Mobile phones * PDAs/pocket PCs * Digital cameras/DSP power supply _______________________________________________________________________________________________________________________________________ Typical Application S3 X 0 0 1 S2 0 0 EN 0 S1 0 EN 0 EN 1 X EN 1 0 1 Sequence ALL OFF DC-DC ON 1st / OFF 1st LDO ON 1st / OFF 1st DC-DC ON 1st / OFF 2nd LDO ON 1st / OFF 2nd ALL ON HyperLight Load and Dual Input LDO are trademarks of Micrel, Inc MLF and MicroLead frame are registered trademarks of Amkor Technology Inc. Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com April 2010 M9999-042210-B Micrel, Inc. MIC23060 > 2Mpixel Camera DSP power Supply Ordering Information Part Number MIC23060-G4YMT Marking Code Nominal Output Voltage1 Junction Temp. Range Package2 XG4 1.8V/1.2V -40 to +125C 12-Pin 2.5mm x 2.5mm Thin MLF(R) Note: 1. Refers to output voltage of DC/DC & LDO respectively. Other voltage options available. Contact Micrel for details. a. DC/DC Converter Voltage Range: 1.7V to 2.5V b. LDO Output Voltage Range: 0.8V to 2.5V (R) 2. Thin MLF is a GREEN RoHS compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free. Pin Configuration (R) 12-Pin 2.5mm x 2.5mm Thin MLF (MT) (Top View) Pin Description Pin Number Pin Name 1 PGND Power Ground. 2 DVIN DC/DC Supply Input Voltage. 3 AVIN Small signal circuitry and Auxiliary LDO Supply Input Voltage. April 2010 Pin Function 4 LDO LDO Regulator Output. 5 SNS Main LDO input supply and feedback for DC-DC converter. Connect to DC/DC VOUT to sense output voltage. 6 DLY Delay. Capacitor to AGND sets a delay time between the first regulator reaching 90% of its regulated voltage and enabling the second regulator. Also programs the turn-off delay, setting the time between the disable of each output. The on/off sequence of the regulators is set by pins S1, S2 and S3. Do not ground. 7 S3 SET Input (3). Active High Input. Logic High = On; Logic Low = Off; do not leave floating. See applications information for set pin configurations. 8 S2 SET Input (2). Active High Input. Logic High = On; Logic Low = Off; do not leave floating. See applications information for set pin configurations. 9 S1 SET Input (1). Active High Input. Logic High = On; Logic Low = Off; do not leave floating. See applications information for set pin configurations. 10 AGND 11 SW 12 NC ePAD ePAD Analog Ground. Switch (Output): Internal power MOSFET output switches. Not Internally connected. Not internally connected, connect to ground plane to maximize heat dissipation. 2 M9999-042210-B Micrel, Inc. MIC23060 Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VAVIN, VDVIN).................................. 0V to 6V Switch Voltage (VSW).............................................. 0V to 6V Switch Current (ISW) .........................................................2A Logic Input Voltage (VS1/2/3).......................... 0V to VIN+0.3V Lead Temperature (soldering, 10sec.)....................... 260C Storage Temperature (Ts)..........................-65C to +150C ESD Rating(4) ................................................. ESD Sensitive Supply Voltage (VAVIN, VDVIN)........................ +2.7V to +5.5V Output Voltage (VLDO).......................................... 0V to 5.5V Logic Input Voltage (VS1/2/3).................................... 0V to VIN Ambient Temperature (TJ)(3) ...................... -40C to +125C Thermal Resistance 2.5mmx2.5mm Thin MLF-12L (JA) ...................66C/W 2.5mmx2.5mm Thin MLF-12L (JC) ...................37C/W Electrical Characteristics(5) VAVIN = VDVIN = 3.6V; IDC-DC = 20mA, ILDO = 100A; L = 2.2H; COUT = 4.7F; COUTLDO = 1F; TA = 25C. Bold values indicate -40C TJ +125C, unless noted. Parameter Condition Min 2.7 Supply Voltage Range Under-Voltage Lockout Threshold 2.45 (Rising) UVLO Hysteresis Total Quiescent Current VS1/2 = High DLY Pin Current Source VDLY = 0V 0.75 DLY Pin Threshold Voltage S1/S2/S3 Input Voltage Typ 2.55 Max Units 5.5 V 2.65 V 50 mV 43 A 1.25 1.75 1.25 Logic Low A V 0.2 V 1.2 Logic High VIL = < 0.2V 0.01 1 A VIH = >1.2V 0.01 1 A Quiescent Current, Hyper LL mode IOUT = 0mA 25 35 A Shutdown Current S1 = S2 = S3 = 0V 0.01 5 A Output Voltage Accuracy Nominal VOUT tolerance +2.5 % 1.7 A S1/S2/S3 Input Current DC/DC Converter -2.5 0.65 Current Limit in PWM Mode Output Voltage Line regulation Output Voltage Load regulation 1 VAVIN = VDVIN = 3.0V to 5.5V, ILOAD = 20mA 0.7 % 20mA < ILOAD DC/DC < 300mA 0.5 % ISW = 100mA PMOS 0.55 ISW = -100mA NMOS 0.6 IOUT LDO = 0mA PWM Switch ON-Resistance Frequency ILOAD DC/DC = 170mA, VOUT = 1.8V Soft-start time VOUT = 0 to 90%, VAVIN = VDVIN = 3.6V Thermal Shutdown Thermal Shutdown Hysteresis April 2010 3 4 MHz 280 s 160 o C 20 o C M9999-042210-B Micrel, Inc. MIC23060 Parameter Condition Min Typ Max Units +3.0 % 1.0 % LDO Regulator -3.0 Output Voltage Accuracy Load Regulation (6) IOUT LDO = 100A to 150mA 0.7 Ground Pin Current IOUT LDO = 100A to 300mA 20 A Ripple Rejection F = up to 1kHz: COUT LDO = 1.0uF 70 dB F = 1kHz to 20kHz; COUT LDO = 1.0F 45 dB Current Limit VOUT = 0V 350 Output Voltage Noise COUT LDO = 1.0F, 10Hz to 100kHz 600 55 800 mA VRMS Notes: 1. Exceeding maximum rating may damage the device. 2. The device is not guaranteed to work outside its operating rating. 3. The maximum allowable power dissipation of any TA (ambient temperature) is PD(max) = (TJ(max) - TA) / JA. Exceeding the maximum allowable power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. 4. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF. 5. Specification for packaged product only. 6. Regulation is measured at constant junction temperature using low duty cycle pulse testing; changes in the output voltage due to heating effects are covered by the thermal regulation specification. April 2010 4 M9999-042210-B Micrel, Inc. MIC23060 Typical Characteristics Voltage Accuracy v s. Tem perature 50 0.04 45 0.03 1.0 0.5 0.0 -0.5 -1.0 LDO Regulation DC-DC Regulation IOUT = 20mA 0.02 REGULATION (%) 0.01 0.00 -0.01 -0.02 IOUT = 600mA -0.03 -1.5 -0.04 -2.0 0 20 40 60 80 100 120 140 T EM PERAT URE (C) 2.5 800 800 750 750 300mA 550 500 100mA 450 300mA 450 350 300 100mA 500 350 5 5.5 2.5 1.88 2.58 1.86 DC-DC OUTPUT VOLTAGE (V) START/STOP VOLTAGE (V) 2.60 2.56 2.54 UVLO(ON) 2.50 2.48 2.46 UVLO(OFF) 2.44 2.42 2.40 3 3.5 4 4.5 INPUT VOLT AGE (V) 5 0 1.78 VIN=3.6V 1.15 1.10 T = 25C 1.00 1000 5.5 70 60 VIN=3.6V VIN=4.2V 50 VIN=5V 40 30 0.1 1.30 1.25 1.20 1.15 1.10 1.05 1 10 100 O UT PUT CURRENT (mA) 1000 Delay Threshold v s. Temperature Delay Pin Current v s. Temperature 1.240 1.235 1.230 1.225 VIN = 3.6V 1.00 5 VIN=3V 0 1 10 100 OUT PUT CURRENT (mA) DELAY THRESHOLD (V) DELAY PIN CURRENT (A) 1.20 0 20 40 60 80 100 120 140 T EM PERAT URE (C) 10 0.1 1.35 April 2010 500 20 1.74 1.40 3.5 4 4.5 INPUT VOLT AGE (V) Sx(OFF) 600 80 VIN=3V 1.76 1.35 3 700 -40 -20 VIN=4.2V 1.80 1.40 2.5 800 DC/DC Efficiency v s. Output Current 1.82 Delay Pin Current v s. Input Voltage 1.05 Sx(ON) 900 90 VIN=5V T EM PERAT URE (C) 1.25 20 40 60 80 100 120 140 T EM PERAT URE (C) 100 1.84 20 40 60 80 100 120 140 1.30 0 1000 5.5 1.72 -40 -20 VIN = 3.6V 5 DC/DC Load Regulation UVLO v s.Tem perature 2.52 10 400 300 3.5 4 4.5 INPUT VOLT AGE (V) 15 1100 550 400 3 20 S1/S2/S3 Enable Threshold v s. Temperature 600 400 2.5 25 600mA 650 600mA 600 30 -40 -20 5.5 700 RDSON (m) RDSON (m) 650 35 DC/DC N-Channel RDS ON v s. Input Voltage DC/DC P-Channel RDS ON v s. Input Voltage 700 3.5 4.5 INPUT VO LT AG E (V) ENABLE THRESHOLD (mV) -40 -20 40 0 -0.05 EFFICIENCY (%) VOUT (% of NO M INAL) 1.5 0.05 QUIESCENT CURRENT (A) 2.0 DELAY PIN CURRENT (A) Quiescent Current v s. Tem perature DC-DC Line Regulation VIN = 3.6V 1.220 -40 -20 0 20 40 60 80 100 120 140 T EM PERAT URE (C) 5 -40 -20 0 20 40 60 80 100 120 140 T EM PERAT URE (C) M9999-042210-B Micrel, Inc. MIC23060 Functional Characteristics April 2010 6 M9999-042210-B Micrel, Inc. MIC23060 Functional Characteristics (Continued) April 2010 7 M9999-042210-B Micrel, Inc. MIC23060 Functional Diagram MIC23060 Block Diagram April 2010 8 M9999-042210-B Micrel, Inc. MIC23060 Functional Description SNS The feedback (SNS) pin is connected to the output of the DC/DC converter to provide feedback to the control circuitry. The SNS connection should be placed close to the output capacitor. Refer to the layout recommendations for more details. DVIN The main input supply (DVIN) provides power to the internal MOSFETs for the switch mode regulator. The DVIN operating range is 2.7V to 5.5V, so an input capacitor, with a minimum voltage rating of 6.3V is recommended. Due to the high switching speed, a minimum 2.2F bypass capacitor placed close to DVIN and the power ground (PGND) pin is required. For best performance a 4.7F capacitor is recommended, refer to the layout recommendations for details. LDO The LDO Output (LDO) pin is the output of the Dual Input LDOTM. Power is provided by the DC/DC output during normal operation and briefly by VAVIN during some start-up and Shutdown sequences. A ceramic bypass capacitor of at least 1F is required. AVIN The Analog input supply (AVIN) provides power to the low power, biasing and control circuitry. Due to the high switching speed of the DC/DC converter, this should ideally be connected away from the DVIN bypass capacitor at the input supply. Refer to layout recommendations for more details. DLY The delay (DLY) pin is connected to an external capacitor and AGND to set the delay time between the first regulator output reaching 90% of its regulated voltage and enabling the second regulator. The same delay time is also used during shutdown. S1/S2/S3 A logic high signal on the Set pins activates the output voltage of the devices in various sequencing modes. A logic low signal on the Set pins deactivates the outputs in various sequences and reduces supply current to 0.01A. Full details of start-up/shutdown sequencing are given in the Application Information section. The MIC23060 features built-in soft-start circuitry that reduces in-rush current and prevents the output voltage from overshooting at start up. Do not leave these pins floating. AGND The analog ground (AGND) is the ground path for the biasing and control circuitry. The current loop for the signal ground should be separate from the power ground (PGND) loop. Refer to the layout recommendations for more details. PGND The power ground pin is the ground path for the high current in PWM mode. The current loop for the power ground should be as small as possible and separate from the analog ground (AGND) loop as applicable. Refer to the layout recommendations for more details. SW The switch (SW) pin connects directly to one end of the inductor and provides the current path during switching cycles. The other end of the inductor is connected to the load, SNS pin and output capacitor. Due to the high speed switching on this pin, the switch node should be routed away from sensitive nodes whenever possible. April 2010 9 M9999-042210-B Micrel, Inc. MIC23060 The MIC23060 was designed for use with a 0.47H to 2.2H inductor. Typically, a 1H inductor is recommended for a balance of transient response, efficiency and output ripple. For faster transient response, a 0.47H inductor will yield the best result. For lower output ripple and improved regulation, a 2.2H inductor is recommended. Maximum current ratings of the inductor are generally given in two methods; permissible DC current and saturation current. Permissible DC current can be rated either for a 40C temperature rise or a 10% to 20% loss in inductance. Ensure the inductor selected can handle the maximum operating current. When saturation current is specified, make sure that there is enough margin so that the peak current does not cause the inductor to saturate. Peak current can be calculated as follows: Application Information The MIC23060 is a high performance DC/DC step down regulator plus Dual input Low Dropout linear regulator offering a small solution size. Supporting a recommended maximum output current of 300mA and 300mA respectively inside a tiny 2.5mm x 2.5mm Thin MLF(R) package and requiring only four external components, the MIC23060 meets today's miniature portable electronic device needs. Using the HyperLight LoadTM switching scheme, the MIC23060 DC/DC converter is able to maintain high efficiency throughout the entire load range while providing ultra-fast load transient response. The following sections provide additional device application information. Input Capacitor A 4.7F ceramic capacitor should be placed close to the DVIN pin and PGND pin for decoupling the high di/dt pulses of the DC-DC section from the LDO section. A TDK C1608X5R0J475K, size 0603, 4.7F ceramic capacitor is recommended based upon performance, size and cost. A X5R or X7R temperature rating is recommended for the input capacitor. Y5V temperature rating capacitors, aside from losing most of their capacitance over temperature, can also become resistive at high frequencies. This reduces their ability to filter out high frequency noise. 1 - VOUT /VIN IPEAK = IOUT + VOUT x 2x f xL As shown by the calculation above, the peak inductor current is inversely proportional to the switching frequency and the inductance; the lower the switching frequency or the inductance the higher the peak current. As input voltage increases, the peak current also increases. The size of the inductor depends on the requirements of the application. Refer to the Typical Application Circuit and Bill of Materials for details. DC resistance (DCR) is also important. While DCR is inversely proportional to size, DCR can represent a significant efficiency loss. Refer to the Efficiency Considerations. Output Capacitor The MIC23060 was designed for use with a 2.2F or greater ceramic output capacitor for the DC-DC section and 1F for the LDO. Increasing the output capacitance will lower output ripple and improve load transient response but could increase solution size or cost. A low equivalent series resistance (ESR) ceramic output capacitor such as the TDK C1608X5R0J475K, size 0603, 4.7F ceramic capacitor is recommended based upon performance, size and cost. Both the X7R or X5R temperature rating capacitors are recommended. The Y5V and Z5U temperature rating capacitors are not recommended due to their wide variation in capacitance over temperature and increased resistance at high frequencies. Compensation The MIC23060 is designed to be stable with a 0.47H to 2.2H inductor with a minimum of 4.7F ceramic (X5R) output capacitor for the DC/DC output (SNS) and 1F ceramic (X5R) for the LDO (LDO). For 0.47H inductors, a 10F capacitor is recommended to reduce ripple and improve stability. Enable Sequencing (S1/S2/S3) The MIC23060 offers complete flexibility of start-up sequencing of its two outputs. The sequence mode is set in hardware (pin-strapping) which requires that only a single GPIO be used for enable toggling. The Dual Input LDOTM can turn-on prior to the DC/DC converter and automatically switch to post regulation from the DC/DC converter after it starts. There are 3 modes available: Inductor Selection When selecting an inductor, it is important to consider the following factors (not necessarily in the order of importance): * Inductance * Rated current value * Size requirements * * S1=S2: Simultaneous (SIM) DC resistance (DCR) * S3 = 0: First On/First Off (FOFO) * S3 = 1: First On/Last Off (FOLO) S3 is responsible for controlling the First-on/First-Off April 2010 10 M9999-042210-B Micrel, Inc. MIC23060 modes, S2 controls the LDO sequence and S1 controls the DC/DC sequence. Here is a Truth Table followed by a flow chart of the sequencing events: S3 S2 S1 X 0 0 0 0 EN 0 EN 0 1 0 EN 1 EN 0 LDO ON 1st / OFF 2nd X 1 1 ALL ON For example, an application where the LDO should be enabled 50ms before the DC/DC and disabled 50ms after the DC-DC, the pins should be set as follows: S1 = 0 S3 = 1 CDLY = 50nF S2 = Enable stimulus Sequence ALL OFF st st DC-DC ON 1 / OFF 1 LDO ON 1st / OFF 1st DC-DC ON 1st / OFF 2nd Detail of the delay timer circuit. Duty Cycle The typical maximum duty cycle of the MIC23060 is 80%. Efficiency Considerations Efficiency is defined as the amount of useful output power, divided by the amount of power supplied. V xI Efficiency(%) = OUT OUT VIN x IIN x 100 Maintaining high efficiency serves two purposes. It reduces power dissipation in the power supply, simplifying thermal design considerations, and it reduces current consumption for battery powered applications. Reduced current draw from a battery increases the devices operating time and is critical in hand held devices. There are two types of losses in switching converters; DC losses and switching losses. DC losses are simply the power dissipation of I2R. Power is dissipated in the high side switch during the on cycle. Power loss is equal to the high side MOSFET RDSON multiplied by the Switch Current squared. During the off cycle, the low side Nchannel MOSFET conducts, also dissipating power. Device operating current also reduces efficiency. The product of the quiescent (operating) current and the supply voltage represents another DC loss. The current required driving the gates on and off at a constant 4MHz frequency and the switching transitions make up the switching losses. Flow Chart of the Enable & Disable sequence DLY The value of capacitor on this pin is used to program the enable and disable delay times. The delay time follows the following equation: TDLY = VDLY.CDLY / IDLY Where nominally: VDLY = 1.25V, IDLY = 1.25A TDLY (ms) = CDLY (nF) April 2010 11 M9999-042210-B Micrel, Inc. MIC23060 the output voltage is over the regulation threshold, then the error comparator turns the PMOS off for a minimumoff-time until the output drops below the threshold. The NMOS acts as an ideal rectifier that conducts when the PMOS is off. Using a NMOS switch instead of a diode allows for lower voltage drop across the switching device when it is on. The asynchronous switching combination between the PMOS and the NMOS allows the control loop to work in discontinuous mode for light load operations. In discontinuous mode, the MIC23060 works in pulse frequency modulation (PFM) to regulate the output. As the output current increases, the off-time decreases, thus provides more energy to the output. This switching scheme improves the efficiency of MIC23060 during light load currents by only switching when it is needed. As the load current increases, the MIC23060 goes into continuous conduction mode (CCM) and switches at a frequency centred at 4MHz. The equation to calculate the load when the MIC23060 goes into continuous conduction mode may be approximated by the following formula: DC/DC Efficiency v s. Output Current 100 VIN=3.6V 90 VIN=3V EFFICIENCY (%) 80 70 60 50 VIN=5V 40 30 20 10 0 0.1 1 10 100 OUT PUT CURRENT (mA) 1000 The figure above shows an efficiency curve. From no load to 100mA, efficiency losses are dominated by quiescent current losses, gate drive and transition losses. By using the HyperLight LoadTM mode, the MIC23060 is able to maintain high efficiency at low output currents. Over 100mA, efficiency loss is dominated by MOSFET RDSON and inductor losses. Higher input supply voltages will increase the Gate-to-Source drive at the internal MOSFETs, thereby reducing the internal RDSON. This improves efficiency by reducing DC losses in the device. All but the inductor losses are inherent to the device. In which case, inductor selection becomes increasingly critical in efficiency calculations. As the inductors are reduced in size, the DC resistance (DCR) can become quite significant. The DCR losses can be calculated as follows: DCR Loss = IOUT2 X DCR From that, the loss in efficiency due to inductor resistance can be calculated as follows: VOUT x IOUT Efficiency_Loss = 1 - VOUT x IOUT + L_PD (V - VOUT ) x D ILOAD > IN 2xLx f As shown in the previous equation, the load at which MIC23060 transitions from HyperLight LoadTM mode to PWM mode is a function of the input voltage (VDVIN), output voltage (VOUT), duty cycle (D), inductance (L) and frequency (f). As shown in the figure below, as the Output Current increases, the switching frequency also increases until the MIC23060 goes from HyperLight LoadTM mode to PWM mode at approximately 120mA. The MIC23060 will switch at a relatively constant frequency around 4MHz once the output current is over 120mA. x 100 Switching Frequency v s. Load Current 10000 Efficiency loss due to DCR is minimal at light loads and gains significance as the load is increased. Inductor selection becomes a trade-off between efficiency and size in this case. L=1H FREQUENCY (kHz) 1000 HyperLight LoadTM Mode MIC23060 uses a minimum on and off time proprietary control loop (patented by Micrel). When the output voltage falls below the regulation threshold, the error comparator begins a switching cycle that turns the PMOS on and keeps it on for the duration of the minimum-on-time. This increases the output voltage. If April 2010 L=2.2H 100 10 L=0.47H 1 0.1 1E-05 0.0001 0.001 0.01 0.1 LOAD CURRENT (A) 12 1 M9999-042210-B Micrel, Inc. MIC23060 Evaluation Board Schematic Bill of Materials Item C1, C2 Part Number GRM188R60J475KE19D Manufacturer Murata 2 Murata Ceramic Capacitor, 1F, 6.3V, X7R 1 GRM188R71C103K Murata Ceramic Capacitor, 10nF, 6.3V, X7R 1 LQM2MPN2R2NG0L Murata 2mm x 1.6mm Multilayer Inductor, 2.2H, 1.2A VLS201610ET-2R2M TDK TDK(2) C3 GRM188R71C105KA12D C4 SW1 R1, R2, R3 U1 Qty. Ceramic Capacitor, 4.7F, 6.3V, X5R C1608X5R0J475K L1 Description (1) 418121270803 Wurth (3) CRCW06031004FKEYE3 Vishay(4) MIC23060-G4YMT Micrel, Inc.(5) 2mm x 1.6mm Power Inductor, 2.2H, 1A 1 2.54mm small SMD DIP Switch (w/raised actuator) 1 Resistor, 1M, 1%. 1/16W, Size 0603 3 Sequenced digital power management IC 1 Notes: 1. Murata: www.murata.com 2. TDK: www.tdk.com 3. Wurth Elektrik: www.we-online.com 4. Vishay: www.vishay.com. 5. Micrel, Inc.: www.micrel.com. April 2010 13 M9999-042210-B Micrel, Inc. MIC23060 PCB Layout Recommendations Top Layer Bottom Layer April 2010 14 M9999-042210-B Micrel, Inc. MIC23060 Package Information (R) 12-Pin Thin MLF (MT) MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2009 Micrel, Incorporated. April 2010 15 M9999-042210-B