Model 3124 Tension/Compression In-Line Load Cell DESCRIPTION The small-diameter, cost-efficient load cells are designed to They may be directly attached to the piston rod of a hydraulic be used in applications that require an ability to mount in an cylinder. Side-mounted cable connectors allow cable assemblies existing system with restricted working area. They are commonly to be supported without affecting movement of the cell during used in fluid power transfer systems. Their low cost and ease of tension or compression loading. mounting allow simultaneous testing of multi-element systems. FEATURES * 5000 lb to 25000 lb range * 0.25 % non-linearity * 0.15 % hysteresis * Adapts directly to hydraulic cylinder * Small diameter allows mounting in restricted areas * Low deflection Model 3124 PERFORMANCE SPECIFICATIONS RANGE CODES Characteristic Measure Range Code Available ranges Load range 5000, 10000, 15000, 20000, 25000 lb DR 5000 lb Non-linearity 0.25 % of rated output DV 10000 lb Hysteresis 0.15 % of rated output EJ 15000 lb Repeatability 0.05 % of rated output EL 20000 lb Output @ rated capacity 2 mV/V (nominal) EM 25000 lb Operation Tension/compression Resolution Infinite Standard calibration Tension (+) and compression (-) 1 ENVIRONMENTAL SPECIFICATIONS Characteristic Measure Temperature, operating -54 C to 93 C [-65 F to 200 F] Temperature, compensated 21 C to 77 C [70 F to 170 F] Temperature effect, zero 0.002 % of rated output/F Temperature effect, output 0.002 % of reading/F ELECTRICAL SPECIFICATIONS Characteristic Measure Strain gage type Foil Excitation (maximum) 20 Vdc or Vac RMS Insulation resistance > 5000 mOhm @ 50 Vdc Bridge resistance (tolerance) 350 ohm Number of bridges 1 or 2 Zero balance 1.0 % TYPICAL SYSTEM DIAGRAM Output Amplifier Universal In-Line Amplifiers +/-5 VDC UV +/-10 VDC UV-10 0 +/-5 VDC UBP 4-20mA (3 wire) U3W 4-20mA (2 wire) U2W DIN rail Mount In-Line Amplifiers 0 +/- 5 VDC (3 wire) DV-05 4-20mA (3 wire) DA-05 0 +/- 10 VDC (3 wire) DV10 Measure Static overload capacity 150 % of nominal capacity Material Carbon steel Natural frequency See table In-Line Amplifier Input Serial Number Display Units MODEL 3124 SC500 SC2001 GM 7541 SC1000 SC3004 NK 7558 SC2000 HH 7561-PSD 2003.1 lb. L1 L2 L3 L4 OR VALUE CLEAR UP DOWN SETUP CHAN TARE ENTER EXIT Mating Connectors & Cables 064-LW13621 Mating connector 7200-76-XX* Mating connector and six conductor cable (unamplified unit with sense leads but not shunt cal) 7200-75-XX** Mating connector (MS - 5 pin) and four conductor cable (unamplified sensor without sense leads) 7200-111-XX** Mating connector ( MS - 5 pin ) & 6 conductor cable for connection to 7541 7200-110-XX** Mating connector ( MS - 5 pin ) & 4 conductor cable for connection to 7541 * XX represents length in feet ** XX represents length in feet 2 Honeywell * Sensing and Control Power Supply Honeywell Output MECHANICAL SPECIFICATIONS Characteristic Customer Supplied Chart Recorder Alarm Panel Data Acquisition Computer PLC In-Line Amplifiers (Used with unamplified units only) 100ft maximum 20ft maximum Tension/Compression In-Line Load Cell NATURAL FREQUENCY Nominal load limit capacity Fz Static extraneous load limits lb N Static overload capacity (% of nominal capacity) Fatigue capacity (% of nominal capacity) Shear FX or FY (lb) Bending MX or MY (lb-in) Torque MZ (lb-in) Deflection at nominal load limit (in) Ringing frequency (Hz) 5K 20K 150 n/a 250 750 15000 0.005 4600 10K 50K 150 n/a 250 700 1100 0.005 6400 15K 75K 150 n/a 450 1300 2100 0.005 7700 20K 100K 150 n/a 650 2000 3000 0.005 8800 25K 125K 150 n/a 950 2700 4500 0.005 9600 MOUNTING DIMENSIONS Model A cm [in] B cm [in] C cm [in] D cm [in] E cm [in] F cm [in] G cm [in] H cm [in] 3124 11,43 [4.50] 2,54 [1.0] 0,97 [0.38] 2,06 [0.81] 3,81 [1.50] 3,51 [1.38] 6,20 [2.44] 4,37 [1.72] RECEP. MS-3102E-14S-5P E HEX H 1.0-14 THD. B C A G D F DIA. E DIA. 1.0-14 THD. B DEEP Honeywell * Sensing and Control 3 Model 3124 Tension/Compression In-Line Load Cell NOTES 1. This unit calibrated to Imperial (non-Metric) units. Warranty. Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Honeywell's standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgement or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items it finds defective. The foregoing is buyer's sole remedy and is in lieu of all warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages. While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the application. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. For more information about Sensing and Control products, visit www.honeywell.com/sensing or call +1-815-235-6847 Email inquiries to info.sc@honeywell.com WARNING PERSONAL INJURY * DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury. WARNING MISUSE OF DOCUMENTATION * The information presented in this catalogue is for reference only. DO NOT USE this document as product installation information. * Complete installation, operation and maintenance information is provided in the instructions supplied with each product. Failure to comply with these instructions could result in death or serious injury. Sensing and Control Automation and Control Solutions Honeywell 1985 Douglas Drive North Golden Valley, MN 55422 USA +1-815-235-6847 www.honeywell.com/sensing 008661-1-EN IL50 GLO May 2008 Copyright (c) 2008 Honeywell International Inc. All rights reserved.