DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger General Description Features The AAT3685 BatteryManagerTM is a highly integrated single cell lithium-ion/polymer battery charger IC designed to operate with USB port or line adapter inputs. It requires the minimum number of external components. * Adapter or USB Charger Programmable up to 1A Max * 4.0V to 5.5V Input Voltage Range * High Level of Integration With Internal: Charging Device Reverse Blocking Diode Current Sensing * Automatic Recharge Sequencing * Charge Reduction Loop * Battery Temperature Monitoring * Full Battery Charge Auto Turn-Off * Over-Voltage Protection * Emergency Thermal Protection * Power On Reset and Soft Start * Serial Interface Status Reporting * 12-Pin 3 x 3mm TDFN Package The AAT3685 precisely regulates battery charge voltage and current for 4.2V lithium-ion/polymer battery cells. Regardless of the type of input power source (USB or adapter), the AAT3685 can be programmed for two separate constant current charge levels up to 1A. An optional Charge Reduction Loop is built in to allow users to charge the battery with available current from the charge supply, while keeping the port voltage regulated. Battery temperature and charge state are fully monitored for fault conditions. In the event of an over-voltage or over-temperature failure, the device will automatically shut down, thus protecting the charging device, control system, and the battery under charge. Status monitor output pins are provided to indicate the battery charge status by directly driving two external LEDs. A serial interface output is available to report any one of 14 various status states to a microcontroller. Applications * * * * * * The AAT3685 is available in a Pb-free, thermally-enhanced, space-saving 12-pin 3 x 3mm TDFN package and is rated over the -40C to +85C temperature range. Cellular Telephones Digital Still Cameras Hand-Held PCs MP3 Players Personal Data Assistants (PDAs) Other Lithium-Ion/Polymer Battery-Powered Devices Typical Application Enable Adapter or USB Input ADP/USB Input Hi/Lo Select PWRSEL RSETH RSETL EN CHR BATT+ SETH BAT SETL TS AAT3685 C2 10F BATT- GND DATA STAT1 TEMP STAT2 Battery Pack Serial Data Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 1 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger Pin Descriptions Pin # Name Type 1 2 3 ADP/USB BAT GND In In/Out Ground 4 CHR In/Out 5 6 7 8 9 10 11 12 EP EN TS DATA STAT2 STAT1 PWRSEL SETL SETH In In/Out In/Out Out Out In In/Out In/Out Function Line adapter or USB power supply input. Battery charging and sensing. Ground connection. Resistor divider to set USB voltage regulation for charge reduction mode. Leave this pin open for default 4.5V USB regulation point. Tie to ADP/USB pin to disable this function. Enable pin. Logic high enables the IC. Connect to 10k NTC thermistor. Status report to microcontroller via serial interface, open-drain. Battery charge status indicator pin to drive an LED: active low, open-drain. Battery charge status indicator pin to drive an LED: active low, open-drain. When ADP/USB is present, use this pin to toggle between SETH and SETL charging levels. Connect resistor here to set charge current for low-current port. Connect resistor here to set charge current for high-current port. Exposed paddle (bottom); connect to GND directly beneath package. Pin Configuration TDFN33-12 (Top View) 2 ADP/USB 1 12 SETH BAT 2 11 SETL GND 3 10 PWRSEL CHR 4 9 STAT1 EN 5 8 STAT2 TS 6 7 DATA Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger AAT3685 Feature Options Product Internal Pull-Up Resistor on EN Pin Can Leave TS Pin Open AAT3685 AAT3685-1 No Yes No Yes Absolute Maximum Ratings1 Symbol VP VP VN TJ TLEAD Description ADP/USB Input Voltage, <30ms, Duty Cycle <10% ADP/USB Input Voltage, Continuous BAT, PWRSEL, SETH, SETL, STAT1, STAT2, DATA, TS, CHR, EN Operating Junction Temperature Range Maximum Soldering Temperature (at leads) Value -0.3 to 7.0 -0.3 to 6.0 -0.3 to VP + 0.3 -40 to 150 300 Units V C Thermal Information2 Symbol JA PD Description Maximum Thermal Resistance (3x3mm TDFN) Maximum Power Dissipation Value Units 50 2.0 C/W W 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Mounted on an FR4 board. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 3 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger Electrical Characteristics1 VADP = 5V, TA = -40C to +85C, unless otherwise noted. Typical values are at TA = 25C. Symbol Description Operation ADP/USB Input Voltage Range Under-Voltage Lockout VUVLO Under-Voltage Lockout Hysteresis IOP Operating Current ISLEEP Sleep Mode Current Reverse Leakage Current from BAT Pin ILeakage VBAT_EOC1 End of Charge Voltage Accuracy VBAT/VBAT EOC Voltage Tolerance VMIN Preconditioning Voltage Threshold VRCH Battery Recharge Voltage Threshold VADP/USB_CHR Charge Reduction Regulation VCHR CHR Pin Voltage Accuracy Current Regulation ICH Charge Current ICH/ICH Charge Current Regulation Tolerance VSETH SETH Pin Voltage VSETL SETL Pin Voltage KIUH Current Set Factor: ICHARGE/ISETH KIUL Current Set Factor: ICHARGE/ISETL Charging Devices Charging MOSFET Transistor On Resistance RDS(ON)U Conditions Min Typ 4.0 Rising Edge CC Charge Current = 500mA VBAT = 4.25V VBAT = 4V, ADP/USB Pin Open 4.158 2.8 No Connection on CHR Pin 4.3 1.9 3.0 150 0.75 0.3 1.0 4.2 0.5 3.0 VBAT_EOC - 0.1 4.5 2.0 50 Units 5.5 V V mV mA A A V % V V V V 1.5 1.0 4.242 3.15 4.64 2.1 1000 mA % V V 0.65 10 2.0 2.0 2000 2000 CC Mode CC Mode VIN = 5.5V Max 0.4 0.5 1. The AAT3685 output charge voltage is specified over the 0 to 70C ambient temperature range; operation over the -40C to +85C temperature range is guaranteed by design. 4 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger Electrical Characteristics1 VADP = 5V, TA = -40C to +85C, unless otherwise noted. Typical values are at TA = 25C. Symbol Description Logic Control / Protection VPWRSEL(H) Input High Threshold VPWRSEL(L) Input Low Threshold VEN(H) Input High Threshold VEN(L) Input Low Threshold VSTAT Output Low Voltage STAT Pin Current Sink Capability ISTAT VOVP Over-Voltage Protection Threshold ITK/ICHG ITERM/ICHG ITERM/ICHG ITS Pre-Charge Current Charge Termination Threshold Current Charge Termination Threshold Current Current Source from TS Pin TS1 TS Hot Temperature Fault TS2 TS Cold Temperature Fault I_DATA VDATA(H) VDATA)(L) SQPULSE tPERIOD fDATA TOVSD DATA Pin Sink Current Input High Threshold Input Low Threshold Status Request Pulse Width System Clock Period Data Output Frequency Over-Temperature Shutdown Threshold Conditions Min Typ Max 1.6 0.4 1.6 0.4 0.4 STAT Pin Sinks 4mA For For For For SETH Mode SETL Mode SETH Mode SETL Mode Threshold Hysteresis Threshold Hysteresis DATA Pin is Active Low State 70 310 2.2 8.0 4.4 10 50 7.5 35 80 330 15 2.3 10 V V V V V mA V % 90 350 2.4 3.0 1.6 0.4 Status Request Units 200 50 20 145 % % A mV V mV mA V V ns s kHz C 1. The AAT3685 output charge voltage is specified over the 0 to 70C ambient temperature range; operation over the -40C to +85C temperature range is guaranteed by design. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 5 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger Typical Characteristics IFASTCHARGE vs. RSET Battery Voltage vs. Supply Voltage 4.242 4.221 1000 VBAT (V) IFASTCHARGE (mA) 10000 SETL 100 SETH 4.200 4.179 10 4.158 1 10 100 1000 4.5 4.75 RSET (k) 5 5.25 5.5 Supply Voltage (V) Recharge Voltage vs. Temperature End of Charge Voltage vs. Temperature 4.242 4.140 4.130 4.120 4.221 VBAT (V) VRCH (V) 4.110 4.100 4.090 4.080 4.070 4.200 4.179 4.060 4.050 4.040 4.158 -50 -25 0 25 50 75 100 -50 -25 Temperature (C) 0 25 50 75 100 Temperature (C) Preconditioning Threshold Voltage vs. Temperature Preconditioning Charge Current vs. Temperature (SETH; SETH = 3.83k ) 120 3.05 3.04 3.03 110 ICH (mA) VMIN (V) 3.02 3.01 3.00 2.99 2.98 100 90 2.97 2.96 2.95 80 -50 -25 0 25 50 Temperature (C) 6 75 100 -50 -25 0 25 50 Temperature (C) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 75 100 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger Typical Characteristics Fast Charge Current vs. Temperature Charging Current vs. Battery Voltage (SETH; SETH = 3.83k ) (SETH; SETH = 3.83k ) 1200 1100 1080 1000 1060 800 ICH (mA) ICH (mA) 1040 1020 1000 980 960 940 600 400 200 920 900 0 -50 -25 0 25 50 75 100 2.5 3 Temperature (C) 4.5 Fast Charge Current vs. Supply Voltage (SETL; SETL = 40.2k ) (SETH; SETH = 3.83k ) 120 1200 100 1000 80 800 ICH (mA) VBAT = 3.3V 60 40 20 VBAT = 3.9V VBAT = 3.5V 600 400 200 0 0 2.5 3 3.5 4 4 4.5 4.25 4.5 4.75 Battery Voltage (V) 5 5.25 5.5 5.75 6 Supply Voltage (V) Fast Charge Current vs. Supply Voltage Fast Charge Current vs. Supply Voltage (SETL; SETL = 40.2k ) (SETH; SETH = 3.83k ) 1200 120 0C VBAT = 3.5V 1000 100 VBAT = 3.9V 70C 800 80 60 ICH (mA) ICH (mA) 4 Battery Voltage (V) Charging Current vs. Battery Voltage ICH (mA) 3.5 VBAT = 3.3V 40 20 25C 600 400 200 0 4 4.5 5 5.5 Supply Voltage (V) 6 6.5 0 4.40 4.50 4.60 4.70 4.80 4.90 5.00 Supply Voltage (V) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 7 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger Typical Characteristics VIH vs. Supply Voltage VIL vs. Supply Voltage EN Pin (Rising) EN Pin (Falling) 1.4 1.4 1.3 1.3 1.2 1.2 -40C +25C 1.1 1.0 VIL (V) VIH (V) 1.1 0.9 0.8 0.7 -40C 0.9 0.8 0.7 +85C 0.6 0.6 0.5 +85C 0.5 0.4 0.4 4.2 4.4 4.6 4.8 5 5.2 5.4 5.6 5.8 6 4.2 4.4 4.6 4.8 Supply Voltage (V) 1.4 1.3 1.3 -40C VIL (V) VIH (V) -40C 1.1 0.9 0.8 6 5.8 6 +25C 1.0 0.9 0.8 +85C 0.6 0.5 0.5 0.4 0.4 4.2 4.4 4.6 4.8 5 5.2 5.4 5.6 5.8 6 4.2 4.4 4.6 4.8 Supply Voltage (V) 5 5.2 5.4 5.6 Supply Voltage (V) Charge Current vs. Time Supply Current vs. SETH Resistor (SETH; SETH = 8.06k ) 0.80 USB VBUS (200mV/div) 0.70 USB Charge Current (200mA/div) 0.60 IQ (mA) 5.8 0.7 +85C 0.6 5.6 1.2 +25C 1.0 0.7 5.4 PWRSEL (Falling) 1.4 1.1 5.2 VIL vs. Supply Voltage PWRSEL (Rising) 1.2 5 Supply Voltage (V) VIH vs. Supply Voltage Constant Current 0.50 Charge Reduction Mode Activated 0.40 0.30 USB Peripheral Current Consumption (200mA/div) Pre-Conditioning 0.20 0.10 0.00 0 1 10 100 SETH Resistor (k ) 8 +25C 1.0 2 4 6 1000 Time (sec) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 8 10 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger Typical Characteristics Temperature Sense Output Current vs. Temperature TS Pin CUrrent (A) 88 86 84 82 80 78 76 74 72 -50 -25 0 25 50 75 100 Temperature (C) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 9 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger Functional Block Diagram Reverse Blocking ADP/USB PWRSEL SETH SETL CHR BAT Current Compare Charge Reduction Loop CV/ Precharge Charge Control Constant Current UVLO OverTemperature Protect STAT1 STAT2 Charge Status 80A DATA TS Serial Data Window Comparator IC enable EN GND Functional Description The AAT3685 is a highly integrated single cell lithiumion/polymer battery charger IC designed to operate from adapter or USB port VBUS supplies, while requiring a minimum number of external components. The device precisely regulates battery charge voltage and current for 4.2V lithium-ion/polymer battery cells. The AAT3685 is specifically designed for being powered from a USB port VBUS supply, but it can also be powered from any input voltage source capable supplying 4.5V to 5.5V for loads up to 1A. The AAT3685 constant charge current can be externally programmed for two levels, SETH and SETL, for maximum constant current charge levels up to 1A. The SETH/L mode has an automatic Charge Reduction Loop control to allow users to charge the battery with limited available current from a port while maintaining the regulated port voltage. This system assures the battery charge function will not overload the port while charging if other system demands also share power with the respective port supply. Status monitor output pins are provided to indicate the battery charge status by directly driving two external 10 LEDs. A serial interface output is available to report 14 various charge states to a system microcontroller. Battery temperature and charge state are fully monitored for fault conditions. In the event of an over-voltage or over-temperature failure, the device will automatically shut down, thus protecting the charging device, control system, and the battery under charge. In addition to internal charge controller thermal protection, the AAT3685 also provides a temperature sense feedback function (TS pin) from the battery to shut down the device in the event the battery exceeds its own thermal limit during charging. All fault events are reported to the user either by the simple status LEDs or via the DATA pin function. Charging Operation The AAT3685 has four basic modes for the battery charge cycle and is powered from the input: pre-conditioning/trickle charge; constant current/fast charge; constant voltage; and end of charge. For reference, Figure 1 shows the current versus voltage profile during charging phases. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger Preconditioning Trickle Charge Phase Constant Current Charge Phase Constant Voltage Charge Phase Charge Complete Voltage I = Max CC Regulated Current Constant Current Mode Voltage Threshold Trickle Charge and Termination Threshold I = CC / 10 Figure 1: Current vs. Voltage Profile During Charging Phases. Battery Preconditioning Before the start of charging, the AAT3685 checks several conditions in order to assure a safe charging environment. The input supply must be above the minimum operating voltage, or under-voltage lockout threshold (VUVLO), for the charging sequence to begin. In addition, the cell temperature, as reported by a thermistor connected to the TS pin from the battery, must be within the proper window for safe charging. When these conditions have been met and a battery is connected to the BAT pin, the AAT3685 checks the state of the battery. If the cell voltage is below the Preconditioning Voltage Threshold (VMIN), the AAT3685 begins preconditioning the cell. The battery preconditioning trickle charge current is equal to the fast charge constant current divided by 10. For example, if the programmed fast charge current is 500mA, then the preconditioning mode (trickle charge) current will be 50mA. Cell preconditioning is a safety precaution for a deeply discharged battery and also aids in limiting power dissipation in the pass transistor when the voltage across the device is at the greatest potential. Fast Charge / Constant Current Charging Battery cell preconditioning continues until the voltage on the BAT pin exceeds the Preconditioning Voltage Threshold (VMIN). At this point, the AAT3685 begins the constant current fast charging phase. The fast charge constant current (ICC) amplitude is determined by the selected charge mode SETH or SETL and is programmed by the user via the RSETH and RSETL resistors. The AAT3685 remains in constant current charge mode until the bat- tery reaches the voltage regulation point, VBAT. Constant Voltage Charging The system transitions to a constant voltage charging mode when the battery voltage reaches output charge regulation threshold (VBAT) during the constant current, fast charge phase. The regulation voltage level is factory programmed to 4.2V ( 1%). The charge current in the constant voltage mode drops as the battery cell under charge reaches its maximum capacity. End of Charge Cycle Termination and Recharge Sequence When the charge current drops to 7.5% of the programmed fast charge current level in the constant voltage mode, the device terminates charging and goes into a sleep state. The charger will remain in a sleep state until the battery voltage decreases to a level below the battery recharge voltage threshold (VRCH). When the input supply is disconnected, the charger will also automatically enter power-saving sleep mode. Only consuming an ultra-low 0.3A in sleep mode, the AAT3685 minimizes battery drain when it is not charging. This feature is particularly useful in applications where the input supply level may fall below the battery charge or under-voltage lockout level. In such cases where the AAT3685 input voltage drops, the device will enter the sleep mode and automatically resume charging once the input supply has recovered from its fault condition. System Operation Flow Chart Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 11 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger Switch On Sleep Mode No UVLO VP > VUVLO Yes SETL Current Loop Input Power 0 Input Detect PWRSEL= ? Power On Reset SETH Current Loop Fault Conditions Monitor OV, OT Yes No Yes Battery Temperature Monitor Shut Down Mode No VTS1 < TS < VTS2 Battery Temp. Fault No Recharge Test VRCH > VBAT Yes Preconditioning Test VMIN > VBAT Yes Low Current Conditioning Charge Input Voltage Regulation Enable No Port Voltage Test VADP/USB < VADP/USB_CHR Yes No Current Phase Test VEOC > VBAT 1 Yes Current Charging Mode Yes Voltage Charging Mode Charge Current Reduction No Voltage Phase Test IBAT > ITERM No Charge Completed 12 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger Application Information USB System Power Charging The USB charge mode provides two programmable fast charge levels up to 1A for each, SETH and SETL. The SETH or SETL modes may be externally selected by the select pin (PWRSEL). When the PWRSEL pin is connected to a logic high level, the SETH level will be active. Conversely, when PWRSEL is pulled to a logic low level (ground), the SETL level will be used for fast charging. These two charge levels may be user programmed to any level between 50mA and 1A by selecting the appropriate resistor values for RSETH and RSETL. Refer to Table 1 for recommended RSETH and RSETL values for the desired input constant current charge levels. SETH SETL ICC RSET (k) RSET (k) 50 75 100 200 300 400 500 600 700 800 900 1000 86.6 57.6 42.2 21.0 13.7 10.2 8.06 6.65 5.62 4.87 4.32 3.83 86.6 57.6 42.2 20.5 13.7 10.2 8.06 6.65 5.62 4.87 4.32 3.83 Table 1: Recommended RSET Values. Charge Reduction In many instances, product system designers do not know the real properties of a potential port to be used to supply power to the battery charger. Typical powered USB ports commonly found on desktop and notebook PCs should supply up to 500mA. In the event a port being used to supply the charger is unable to provide the programmed fast charge current, or if the system under charge must also share supply current with other functions, the AAT3685 will automatically reduce USB fast charge current to maintain port integrity and protect the host system. The charge reduction system becomes active when the voltage on the input falls below the charge reduction threshold (VADP/USB_CHR), which is typically 4.5V. Regardless of which charge function is selected (SETH or SETL), the charge reduction system will reduce the fast charge current level in a linear fashion until the voltage sensed on the input recovers above the charge reduction threshold voltage. The charge reduction threshold (VADP/USB_CHR) may be externally set to a value lower than 4.5V by placing a resistor divider network between VADP/USB and ground with the center connected to the CHR pin. The charge reduction feature may be disabled by connecting a 10k resistor from the CHR pin directly to the ADP/ USB input pin. The following equation may be used to approximate a USB charge reduction threshold below 4.5V: Eq. 1: VADP/USB_CHR = 2.0V / where R11/R12 << 1M. R12 R12 + R11 VADP/USB R11 ADP/USB 1.025M CHR VCHR = 2.0V R12 825k Figure 2: Internal Equivalent Circuit for the CHR Pin. Input Charge Inhibit and Resume The AAT3685 UVLO and power on reset feature will function when the input pin voltage level drops below the UVLO threshold. At this point, the charger will suspend charging and shut down. When power is re-applied to the ADP/USB pin or the UVLO condition recovers, the system charge control will assess the state of charge on the battery cell and will automatically resume charging in the appropriate mode for the condition of the battery. Single Path Charging from a Line Adapter or USB Source Most USB charging applications limit charging current to 500mA due to the limitations of a USB port as a power source. The AAT3685 is capable of, and may be programmed for, constant current charge levels up to 1A. Thus, charging operation is not just restricted to use with USB port supplies. Any power source may be used Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 13 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger In order to fully utilize the power capacity from a line adapter or USB port supply, program the SETH charge rate according to the highest charging current capacity of the two possible sources, providing that neither supply exceeds 1A. A lower charge level may be set with the SETL charge rate and selection of the higher or lower charge rate is controlled via the PWRSEL function. If the programmed charge rate is greater than the current source capacity, there is little danger of system failure because the AAT3685 charge reduction loop will activate to automatically reduce the charging current and maintain a supply voltage set by the CHR threshold. If the input supply is incapable of maintaining an input voltage greater than the under-voltage lockout level of the AAT3685, the charge control will suspend charging until the source supply is capable of supplying the minimum input current to charge. At this point, the AAT3685 will automatically resume charging in the appropriate mode based on the battery cell voltage. In case of an over-temperature condition with a high charge current and large input-to-battery voltage difference, the device will cycle from charging to thermal shutdown and re-charge after temperature drops sufficiently, until the battery is charged to 4.2V. Enable / Disable The AAT3685 provides an enable function to control the charger IC on and off. The enable (EN) pin is an active high. When pulled to a logic low level, the AAT3685 will be shut down and forced into the sleep state. Charging will be halted regardless of the battery voltage or charging state. When the device is re-enabled, the charge control circuit will automatically reset and resume charging functions with the appropriate charging mode based on the battery charge state and measured cell voltage. Programming Charge Current The fast charge constant current charge level for the ADP/USB input is programmed with set resistors placed between the SETH and SETL pins and ground. The accuracy of the fast charge, as well as the preconditioning trickle charge current, is dominated by the tolerance of the set resistors used. For this reason, 1% tolerance metal film resistors are recommended for programming the desired constant current level. 14 The fast charge constant current charge control provides for two current set levels, SETH and SETL. The PWRSEL pin is used to select the high or low charge current levels. When the PWRSEL pin is pulled to a voltage level above the VPWRSEL(H) threshold, the SETH current level will be selected. Conversely, this pin should be pulled below the VPWRSEL(L) to enable the SETL charge level. These two charge levels may be set to any level between 50mA and 1A, depending upon the system design requirements for a given charge application. Refer to Table 1 and Figure 3 for recommended RSETH and RSETL values. 10000 IFASTCHARGE (mA) within the operating voltage limits as specified in the Electrical Characteristics section of this datasheet. This makes the AAT3685 perfect for applications that only have one input path, but may access either a line adapter source or a USB port supply. 1000 USBL 100 USBH 10 1 10 100 1000 RSET (k ) Figure 3: IFASTCHARGE vs. RSET. Protection Circuitry Over-Voltage Protection An over-voltage event is defined as a condition where the voltage on the BAT pin exceeds the maximum battery charge voltage and is set by the over-voltage protection threshold (VOVP). If an over-voltage condition occurs, the AAT3685 charge control will shut down the device until voltage on the BAT pin drops below the overvoltage protection threshold (VOVP). The AAT3685 will resume normal charging operation after the over-voltage condition is removed. During an over-voltage event, the STAT LEDs will report a system fault; the actual fault condition may also be read via the DATA pin signal. Over-Temperature Shutdown The AAT3685 has a thermal protection control circuit which will shut down charging functions should the internal die temperature exceed the preset thermal limit threshold. Battery Temperature Fault Monitoring In the event of a battery over-temperature condition, the charge control will turn off the internal pass device and report a battery temperature fault on the DATA pin function. The STAT LEDs will also display a system fault. After Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger the system recovers from a temperature fault, the device will resume charging operation. The AAT3685 checks battery temperature before starting the charge cycle, as well as during all stages of charging. This is accomplished by monitoring the voltage at the TS pin. This system is intended for use negative temperature coefficient (NTC) thermistors which are typically integrated into the battery package. Most commonly used NTC thermistors used in battery packs are approximately 10k at room temperature (25C). The TS pin has been specifically designed to source 80A of current to the thermistor. The voltage on the TS pin that results from the resistive load should stay within a window from 335mV to 2.32V. If the battery becomes too hot during charging due to an internal fault, the thermistor will heat up and reduce in value, thus pulling the TS pin voltage lower than the TS1 threshold, and the AAT3685 will halt charging and signal the fault condition. If the use of the TS pin function is not required by the system, it should be terminated to ground using a 10k resistor. Alternatively, on the AAT3685-1, the TS pin may be left open. Event Description STAT1 STAT2 Charge Disabled or Low Supply Charge Enabled Without Battery Battery Charging Charge Completed Fault Off Flash1 On Off On Off Flash1 Off On On Table 2: LED Display Status Conditions. The LED anodes should be connected to VADP/USB. The LEDs should be biased with as little current as necessary to create reasonable illumination; therefore, a ballast resistor should be placed between each of the LED cathodes and the STAT1/2 pins. LED current consumption will add to the over-thermal power budget for the device package, hence it is recommended to keep the LED drive current to a minimum. 2mA should be sufficient to drive most low-cost green, red, or multi-color LEDs. It is not recommended to exceed 8mA for driving an individual status LED. The required ballast resistor value can be estimated using the following formulas: Battery Charge Status Indication The AAT3685 indicates the status of the battery under charge with two different systems. First, the device has two status LED driver outputs. These two LEDs can indicate simple functions such as no battery charge activity, battery charging, charge complete, and charge fault. The AAT3685 also provides a bi-directional data reporting function so that a system microcontroller may interrogate the DATA pin and read any one of 14 system states. Status Indicator Display Simple system charging status may be displayed using one or two LEDs in conjunction with the STAT1 and STAT2 pins on the AAT3685. These two pins are simple switches to connect the display LED cathodes to ground. It is not necessary to use both display LEDs if a user simply wants to have a single lamp to show "charging" or "not charging." This can be accomplished by just using the STAT1 pin and a single LED. Using two LEDs and both STAT pins simply gives the user more information for charging states. Refer to Table 2 for LED display definitions. Eq. 2: RB(STAT1/2) = (VAPD/USB - VF(LED)) ILED(STAT1/2) Example: RB(STAT1) = (5.0V - 2.0V) = 1.5k 2mA Note: Red LED forward voltage (VF) is typically 2.0V @ 2mA. Table 2 shows the four status LED display conditions. Digital Charge Status Reporting The AAT3685 has a comprehensive digital data reporting system by use of the DATA pin feature. This function can provide detailed information regarding the state of the charging system. The DATA pin is a bi-directional port which will read back a series of data pulses when the system microcontroller asserts a request pulse. This single strobe request protocol will invoke one of 14 possible return pulse counts in which the microcontroller can look up based on the serial report shown in Table 3. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 15 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger N DATA Report Status 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Chip Over-Temperature Shutdown Battery Temperature Fault Over-Voltage Turn Off Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used SETH Battery Condition Mode SETH Charge Reduction in Constant Current Mode SETH Constant Current Mode SETH Constant Voltage Mode SETH End of Charging SETL Battery Condition Mode SETL Charge End of Charging Reduction in Constant Current Mode SETL Constant Current Mode SETL Constant Voltage Mode SETL End of Charging Data Report Error 19 20 21 22 23 Table 3: Serial Data Report Table. The DATA pin function is active low and should normally be pulled high to VADP/USB. This data line may also be pulled high to the same level as the high state for the logic I/O port on the system microcontroller. In order for the DATA pin control circuit to generate clean sharp edges for the data output and to maintain the integrity of the data timing for the system, the pull-up resistor on the data line should be low enough in value so that the DATA signal returns to the high state without delay. If the value of the pull-up resistor used is too high, the strobe pulse from the system microcontroller may exceed the maximum pulse time and the DATA output control could issue false status reports. A 1.5k resistor is recommended when pulling the DATA pin high to 5.0V at the VUSB input. If the data line is pulled high to a voltage level less than 5.0V, the pull-up resistor may be calculated based on a recommended minimum pull-up current of 3mA. Use the following formula: Eq. 3: RPULL-UP VPULL-UP 3mA Data Timing The system microcontroller should assert an active low data request pulse for minimum duration of 200ns; this is specified by TLO(DATA). Upon sensing the rising edge of the end of the data request pulse, the AAT3685 status data control will reply the data word back to the system microcontroller after a delay specified by the data report time specification TDATA(RPT). The period of the following group of data pulses will be specified by the TDATA specification. 1.8V to 5.0V IN AAT3685 Status Control RPULL_UP IN DATA Pin GPIO OUT OUT P GPIO Port Figure 4: Data Pin Application Circuit. 16 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger Timing Diagram SQPULSE SQ PDATA System Reset System Start CK TSYNC Data TLAT TDATA(RPT) = TSYNC + TLAT < 2.5 PDATA TOFF > 2 PDATA Thermal Considerations The AAT3685 is packaged in a Pb-free, 3x3mm TDFN package which can provide up to 2.0W of power dissipation when it is properly bonded to a printed circuit board and has a maximum thermal resistance of 50C/W. Many considerations should be taken into account when designing the printed circuit board layout, as well as the placement of the charger IC package in proximity to other heat generating devices in a given application design. The ambient temperature around the charger IC will also have an affect on the thermal limits of a battery charging application. The maximum limits that can be expected for a given ambient condition can be estimated by the following discussion. First, the maximum power dissipation for a given situation should be calculated: Eq. 4: PD = [(VIN - VBAT) * ICC + (VIN * IOP)] Where: PD VIN VBAT ICC IOP = = = = Total Power Dissipation by the Device Input Voltage Level, VADP/USB Battery Voltage as Seen at the BAT Pin Maximum Constant Fast Charge Current Programmed for the Application = Quiescent Current Consumed by the Charger IC for Normal Operation Next, the maximum operating ambient temperature for a given application can be estimated based on the thermal resistance of the 3x3mm TDFN package when suf- TOFF N=1 N=3 N=2 ficiently mounted to a PCB layout and the internal thermal loop temperature threshold. Eq. 5: TA = TJ - (JA * PD) Where: TA = Ambient Temperature in C TJ = Maximum Device Junction Temperature Protected by the Thermal Limit Control PD = Total Power Dissipation by the Device JA = Package Thermal Resistance in C/W Example: For an application where the fast charge current is set to 500mA, VUSB = 5.0V and the worst case battery voltage at 3.0V, what is the maximum ambient temperature at which the thermal limiting will become active? Given: VUSB VBAT ICC IOP TJ JA = = = = = = 5.0V 3.0V 500mA 0.75mA 140C 50C/W Using Equation 4, calculate the device power dissipation for the stated condition: Eq. 6: PD = (5.0V - 3.0V)(500mA) + (5.0V * 0.75mA) = 1.00375W Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 17 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger The maximum ambient temperature before the AAT3685 thermal limit protection will shut down charging can now be calculated using Equation 5: Eq. 7: TA = 140C - (50C/W * 1.00375W) = 89.81C Therefore, under the stated conditions for this worst case power dissipation example, the AAT3685 will suspend charging operations when the ambient operating temperature rises above 89.81C. Capacitor Selection Input Capacitor In general, it is good design practice to place a decoupling capacitor between the ADP/USB pin and ground. An input capacitor in the range of 1F to 22F is recommended. If the source supply is unregulated, it may be necessary to increase the capacitance to keep the input voltage above the under-voltage lockout threshold during device enable and when battery charging is initiated. If the AAT3685 input is to be used in a system with an external power supply source rather than a USB port VBUS, such as a typical AC-to-DC wall adapter, then a CIN capacitor in the range of 10F should be used. A larger input capacitor in this application will minimize switching or power bounce effects when the power supply is "hot 18 plugged" in. Likewise, a 10F or greater input capacitor is recommended for the USB input to help buffer the effects of USB source power switching noise and input cable impedance. Output Capacitor The AAT3685 only requires a 1F ceramic capacitor on the BAT pin to maintain circuit stability. This value should be increased to 10F or more if the battery connection is made any distance from the charger output. If the AAT3685 is to be used in applications where the battery can be removed from the charger, such as in the case of desktop charging cradles, an output capacitor greater than 10F may be required to prevent the device from cycling on and off when no battery is present. Printed Circuit Board Layout Considerations For the best results, it is recommended to physically place the battery pack as close as possible to the AAT3685 BAT pin. To minimize voltage drops on the PCB, keep the high current carrying traces adequately wide. For maximum power dissipation of the AAT3685 3x3mm TDFN package, the metal substrate should be solder bonded to the board. It is also recommended to maximize the substrate contact to the PCB ground plane layer to further increase local heat dissipation. Refer to the AAT3685 evaluation board for a good layout example (see Figures 5 and 6). Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger AAT3685 Evaluation Board Layout Figure 5: AAT3685 Evaluation Board Component Side Layout. Figure 6: AAT3685 Evaluation Board Solder Side Layout. AAT3685 Evaluation Board Schematic Diagram ON/OFF PWRSEL J1 J2 1 2 3 1 2 3 Mini-B HI LO 5 4 3 2 1 GND ID D+ DADP/USB RED GRN LED D2 LED D1 C2 TB1 ADP/USB GND 10F 1 2 R3 R2 Open Open U1 1 5 BAT TS GND 2 1 2 3 AAT3685 ADP/USB EN BAT PWRSEL STAT2 STAT1 DATA TB2 4 C1 SETL CHR SETH 10F 6 R4 10K R1 Open TS GND 3 TDFN33-12 R6 1.5K R5 1.5K R9 1.5K 10 8 9 7 DATA 11 12 R8 R7 8.06K 40.2K SW1 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 19 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger AAT3685 Evaluation Board Bill of Materials (BOM) Quantity 1 1 1 1 2 1 1 2 1 3 1 1 1 1 20 Description Test Pin Connecting Terminal Block, 2.54mm, 2 Pos Connecting Terminal Block, 2.54mm, 3 Pos USB 2.0 Receptacle, 5 Pos Capacitor, Ceramic, 10F 6.3V 10% X5R 0805 Typical Red LED, Super Bright Typical Green LED Header, 3-Pin Resistor, 10k 1/16W 5% 0603 SMD Resistor, 1.5k 1/16W 1% 0603 SMD Resistor, 40.2k 1/16W 1% 0603 SMD Resistor, 8.06k 1/16W 1% 0603 SMD Switch Tact 6mm SPST H = 5.0mm AAT3685 Lithium-Ion/ Polymer Battery Charger Desig. Footprint Manufacturer Part Number DATA PAD Mill-Max 6821-0-0001-00-00-08-0 USB, GND TBLOK2 Phoenix Contact 277-1274-ND BAT, GND, TS USB TBLOK3 Phoenix Contact 277-1273-ND USB-MINI-B Hirose Electronic Co. Ltd. H2959CT-ND C1, C2 0805 Murata 490-1717-1-ND D1 D2 J1, J2 1206LED 1206LED HEADER2MM-3 Chicago Miniature Lamp Chicago Miniature Lamp Sullins CMD15-21SRC/TR8 CMD15-21VGC/TR8 6821-0-0001-00-00-08-0 R4 0603 Panasonic/ECG P10KCFCT-ND R5, R6, R9 0603 Panasonic/ECG P1.5KCGCT-ND R7 0603 Panasonic/ECG P40.2KHTR-ND R8 0603 Panasonic/ECG P8.06KHCT-ND SW1 SWITCH ITT Industries/ C&K Div. CKN9012-ND U1 TDFN33-12 Skyworks AAT3685IWP Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 DATA SHEET AAT3685 Li-Ion/Polymer Battery Charger Ordering Information Package Marking1 Part Number (Tape and Reel)2 TDFN33-12 RNXYY AAT3685IWP-4.2-T1 Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04-0074. Package Information TDFN33-12 Index Area 0.43 0.05 Detail "A" 0.45 0.05 2.40 0.05 3.00 0.05 0.1 REF C0.3 3.00 0.05 1.70 0.05 Top View Bottom View 0.23 0.05 Pin 1 Indicator (optional) 0.05 0.05 0.23 0.05 0.75 0.05 Detail "A" Side View All dimensions in millimeters. 1. XYY = assembly and date code. 2. Sample stock is generally held on part numbers listed in BOLD. 3. The leadless package family, which includes QFN, TQFN, DFN, TDFN and STDFN, has exposed copper (unplated) at the end of the lead terminals due to the manufacturing process. A solder fillet at the exposed copper edge cannot be guaranteed and is not required to ensure a proper bottom solder connection. Copyright (c) 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. ("Skyworks") products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and "Breakthrough Simplicity" are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201888B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 25, 2012 21