ICS9248-50 Integrated Circuit Systems, Inc. Frequency Timing Generator for Pentium II Systems General Description Features The ICS9248-50 * * ICS9248-50 * * Block Diagram * * Generates the following system clocks: - 2 CPU (2.5V) up to 100MHz. - 6 PCI (3.3V) @ 33.3MHz (Includes one free running). - 2 REF clks (3.3V) at 14.318MHz. Skew characteristics: - CPU - CPU<175ps - PCI - PCI < 500ps - CPU(early) - PCI = 1.5ns - 4ns. Supports Spread Spectrum modulation for CPU and PCI clocks, 0.5% down spread Efficient Power management scheme through stop clocks and power down modes. Uses external 14.318MHz crystal, no external load cap required for CL=18pF crystal. 28-pin (209 mil) SSOP package Pin Configuration 28-Pin SSOP Power Groups 0278I--06/03/03 ICS9248-50 Pin Descriptions Pin number Pin name Type 1 2 3 4 5,6,9,10,11 7 8 12 GNDREF X1 X2 PCICLK_F PCICLK (1:5) GNDPCI VDDPCI VDD48 Power Input Output Output Output Power Power Power Ground for 14.318 MHz reference clock outputs 14.318 MHz crystal input 14.318 MHz crystal output 3.3 V free running PCI clock output, will not be stopped by the PCI_STOP# 3.3 V PCI clock outputs, generating timing requirements for Pentium IIa Ground for PCI clock outputs 3.3 V power for the PCI clock outputs 3.3 V power for 48/24 MHz clocks Description 13 48 MHz Output 3.3 V 48 MHz clock output, fixed frequency clock typically used with USB devices 14 TS#/48/24MHz Output 15 GND48 Power 16 SEL 100/66# Input 17 PD# Input Asynchronous active low input pin used to power down the device into a low power state. The internal clocks are disabled and the VCO and the crystal are stopped. The latency of the power down will not be greater than 3ms. 18 CPU_STOP# Input Asynchronous active low input pin used to stop the CPUCLK in active low state, all other clocks will continue to run. The CPUCLK will have a "Turnon " latency of at least 3 CPU clocks. 19 VDD Power Isolated 3.3 V power for core 20 PCI-Stop# Input Synchronous active low input used to stop the PCICLK in active low state. It will not effect PCICLK_F or any other outputs. 21 22 23,24 25 GND GNDL CPUCLK(1:0) VDDL Power Power Output Power 26 REF1/SPREAD# Output 27 REF0/SEL48# Output 3.3 V 14.318 MHz reference clock output and power-on 48/24 MHz select option. Active low = 48 MHz output at pin 14. Active high = 24 MHz output at pin 14. 28 VDDREF Power 3.3 V power for 14.318 MHz reference clock outputs. 3.3 V 48 or 24 MHz output and Tri-state option, active low = tri state mode for testing, active high = normal operation Ground for 48/24 MHz clocks control for the frequency of clocks at the CPU & PCICLK output pins. If logic "0" is used the 66.6 MHz frequency is selected. If Logic "1" is used, the 100 MHz frequency is selected. The PCI clock is multiplexed to run at 33.3 MHz for both selected cases. Isolated ground for core Ground for CPU clock outputs 2.5 V CPU clock outputs 2.5 V power for CPU clock outputs 3.3 V 14.318 MHz reference clock output and power-on spread spectrum enable option. Active low = spread spectrum clocking enable. Active high = spread spectrum clocking disable. 0278I--06/03/03 2 ICS9248-50 Select Functions Functionality CPUCLK PCI, PCI_F Tristate HI - Z HI - Z 1 Testmode TCLK/2 REF0 HI - Z 1 TCLK1 TCLK/6 SEL 100/66# TS# Function 0 0 Tri-State 0 - (Reser ved) 0 - (Reser ved) 0 1 Active 66.6MHz CPU, 33.3 PCI 1 0 Test Mode 1 - (Reser ved) 1 - (Reser ved) 1 1 Active 100MHz CPU, 33.3 PCI Power Management Clock Enable Configuration C P U _ S TO P # X 0 0 1 1 P C I _ S TO P # X 0 1 0 1 P W R _ DW N # 0 1 1 1 1 CPUCLK L ow Low Low 100/66.6MHz 100/66.6MHz PCICLK L ow Low 33.3 MHz Low 33.3 MHz PCICLK_F L ow 33.3MHz 33.3MHz 33.3MHz 33.3MHz REF Stopped Running Running Running Running Cr ystal Off Running Running Running Running VCOs Off Running Running Running Running ICS9248-50 Power Management Requirements SIGNAL SIGNAL STATE CPU_ STOP# 0 (Disabled)2 1 (Enabled)1 0 ( D i s a bl e d ) 2 1 (Enabled)1 1 ( N o r m a l O p e ra t i o n ) 3 0 (Power Down)4 PCI_STOP# PD# L a t e n cy No. of rising edg es of free running PCICLK 1 1 1 1 3ms 2max Notes. 1. Clock on latency is defined from when the clock enable goes active to when the first valid clock comes out of the device. 2. Clock off latency is defined from when the clock enable goes inactive to when the last clock is driven low out of the device. 3. Power up latency is when PD# goes inactive (high) to when the first valid clocks are output by the device. 4. Power down has controlled clock counts applicable to CPUCLK, PCICLK only. The REF will be stopped independant of these. 0278I--06/03/03 3 ICS9248-50 CPU_STOP# Timing Diagram ICS9248-50 Notes: 1. All timing is referenced to the internal CPUCLK. 2. CPU_STOP# is an asynchronous input and metastable conditions may exist. This signal is synchronized to the CPUCLKs inside the ICS9248-50. 3. All other clocks continue to run undisturbed. 4. PD# and PCI_STOP# are shown in a high (true) state. PCI_STOP# Timing Diagram ICS9248-50 ICS9248-50 Notes: 1. All timing is referenced to the Internal CPUCLK (defined as inside the ICS9248 device.) 2. PCI_STOP# is an asynchronous input, and metastable conditions may exist. This signal is required to be synchronized inside the ICS9248. 3. All other clocks continue to run undisturbed. 4. PD# and CPU_STOP# are shown in a high (true) state. 0278I--06/03/03 4 ICS9248-50 PD# Timing Diagram ICS9248-50 Notes: 1. All timing is referenced to the Internal CPUCLK (defined as inside the ICS9248 device). 2. PD# is an asynchronous input and metastable conditions may exist. This signal is synchronized inside the ICS9248. 3. The shaded sections on the VCO and the Crystal signals indicate an active clock is being generated. 0278I--06/03/03 5 ICS9248-50 Absolute Maximum Ratings DD +0.5 V Ambient Operating Temperature . . . . . . . . . . 0C to +70C Case Temperature . . . . . . . . . . . . . . . . . . . . . 0C to +115C Storage Temperature . . . . . . . . . . . . . . . . . . . -65C to +150C Absolute Maximum Ratings Electrical Characteristics - Input/Supply/Common Output Parameters TA = 0 - 70C; Supply Voltage VDD = 3.3 V +/-5%, V DDL = 2.5 V +/-5% (unless otherwise stated) PARAMETER Input High Voltage Input Low Voltage Input High Current Input Low Current Input Low Current Operating Supply Current Power Down Supply Current Input frequency Input Capacitance1 Transition Time1 1 Clk Stabilization Skew1 SYMBOL VIH VIL IIH I IL1 I IL2 I DD3.3OP66 IDD3.3OP100 I DD2.5OP66 IDD2.5OP100 IDD3.3PD CONDITIONS VIN = V DD VIN = 0 V; Inputs with no pull-up resistors VIN = 0 V; Inputs with pull-up resistors CL = 0 pF; Select @ 66MHz CL = 0 pF; Select @ 100MHz CL = 0 pF; Select @ 66.8 MHz CL = 0 pF; Select @ 100 MHz MIN 2 VSS - 0.3 -5 -200 CL = 0 pF; With input address to Vdd or GND 0.1 2.0 -100 60 66 16 23 MAX UNITS VDD + 0.3 V 0.8 V 5 mA mA mA 180 mA 180 mA 72 mA 100 mA 70 600 mA 14.318 16 MHz 36 5 45 pF pF Fi VDD = 3.3 V; CIN CINX Logic Inputs X1 & X2 pins Ttrans To 1st crossing of target Freq. 3 ms From V DD = 3.3 V to 1% target Freq. VT = 1.5 V; VTL = 1.25 V 3 ms 4 ns TSTAB TCPU-PCI 11 TYP 27 0278I--06/03/03 6 1.5 3 ICS9248-50 Electrical Characteristics - CPUCLK TA = 0 - 70C; VDD = 3.3 V +/-5%, VDDL = 2.5 V +/-5%; CL = 10 - 20 pF (unless otherwise stated) PARAMETER Output High Voltage Output Low Voltage Output High Current Output Low Current SYMBOL V OH2B V OL2B IOH2B IOL2B Rise Time t r2B1 t f2B1 dt2B1 tsk2B1 Fall Time Duty Cycle Skew Jitter MIN 1.8 VOL = 0.4 V, VOH = 2.0 V 0.4 1.15 1.6 ns VOH = 2.0 V, V OL = 0.4 V 0.4 1.4 1.6 ns VT = 1.25 V 44 48 55 % 10 134 10 175 10.5 ps ns 186 200 ps 150 +250 ps VT = 1.25 V period(norm) VT = 1.25 V; 100MHz Jitter Jitter, Absolute 1 CONDITIONS IOH = -12.0 mA IOL = 12 mA VOH = 1.7 V VOL = 0.7 V t jcyc-cyc2B1 t jabs2B1 VT = 1.25 V VT = 1.25 V TYP 2.3 0.31 27 -250 MAX UNITS V 0.4 V -27 mA mA Guaranteed by design, not 100% tested in production. Electrical Characteristics - REF/48MHz/24MHz TA = 0 - 70C; V DD = 3.3 V +/-5%, VDDL = 2.5 V +/-5%; CL = 10 - 20 pF (unless otherwise stated) PARAMETER Output High Voltage Output Low Voltage Output High Current Output Low Current Rise Time1 SYMBOL VOH5 VOL5 IOH5 IOL5 tr5 VOL = 0.4 V, VOH = 2.4 V 1.4 4 ns Fall Time1 tf5 VOH = 2.4 V, VOL = 0.4 V 1.1 4 ns 53 185 385 169 469 55 250 800 250 800 % ps ps ps ps 1 Duty Cycle Jitter1 Jitter1 dt5 tj1s5 tjabs5 tj1s5 tjabs5 CONDITIONS IOH = -12 mA IOL = 9 mA VOH = 2.0 V VOL = 0.8 V VT = VT = VT = VT = VT = 1.5 V 1.5 V, 1.5 V, 1.5 V, 1.5 V, MIN 2.6 16 45 REF REF 48 MHz 48 MHz 0278I--06/03/03 7 TYP 3.1 0.17 -44 42 MAX UNITS V 0.4 V -22 mA mA ICS9248-50 Electrical Characteristics - PCICLK TA = 0 - 70C; VDD = 3.3 V +/-5%, VDDL = 2.5 V +/-5%; CL = 30 pF PARAMETER Output High Voltage Output Low Voltage Output High Current Output Low Current Rise Time1 CONDITIONS IOH = -18 mA IOL = 9.4 mA VOH = 2.0 V VOL = 0.8 V MIN 2.1 TYP 3.3 0.1 16 MAX UNITS V 0.4 V -22 mA 57 mA tr1 VOL = 0.4 V, VOH = 2.4 V 1.6 2 ns tf1 VOH = 2.4 V, VOL = 0.4 V 1.8 2 ns dt1 VT = 1.5 V 50 55 % Skew t sk1 Jitter1 tjcyc-cyc tj1s tjabs VT = VT = VT = VT = 222 186 52 200 500 500 150 500 ps ps ps ps 1 Fall Time 1 Duty Cycle 1 1 SYMBOL VOH1 VOL1 IOH1 IOL1 45 1.5 V 1.5 V 1.5 V 1.5 V Guaranteed by design, not 100% tested in production. 0278I--06/03/03 8 ICS9248-50 General Layout Precautions: Notes: Capacitor Values: 0278I--06/03/03 9 ICS9248-50 SYMBOL In Millimeters In Inches COMMON DIMENSIONS COMMON DIMENSIONS MIN MAX MIN MAX A - 2.00 - .079 A1 0.05 - .002 - A2 1.65 1.85 .065 .073 b 0.22 0.38 .009 .015 c 0.09 0.25 SEE VARIATIONS D E 7.40 E1 5.00 5.60 0.65 BASIC .197 .220 0.0256 BASIC 0.55 0.95 SEE VARIATIONS .022 .037 SEE VARIATIONS e L N 8.20 .0035 .010 SEE VARIATIONS 0 .291 .323 8 0 8 MIN MAX MIN MAX 8 2.70 3.30 .106 .130 14 5.90 6.50 .232 .256 16 5.90 6.50 .232 .256 18 6.90 7.50 .271 .295 20 6.90 7.50 .271 .295 22 7.90 8.50 .311 .335 24 7.90 8.50 .311 .335 28 9.90 10.50 .390 .413 30 9.90 10.50 .390 .413 38 12.30 12.90 VARIATIONS N D mm. D (inch) .484 .508 MO-150 JEDEC Doc.# 10-0033 6/1/00 Rev B Ordering Information 9248yF-50-T XXXX y F - PPP - T Designation for tape and reel packaging Pattern Number (2 or 3 digit number for parts with ROM code patterns) Package Type F=SSOP Revision Designator Device Type (consists of 3 or 4 digit numbers) 0278I--06/03/03 10