H Hermetically Sealed, Low IF, Wide VCC, Logic Gate Optocouplers Technical Data HCPL-520X* 5962-88768 HCPL-523X HCPL-623X HCPL-625X 5962-88769 *See matrix for available extensions. Features * Dual Marked with Device Part Number and DESC Drawing Number * Manufactured and Tested on a MIL-PRF-38534 Certified Line * QML-38534, Class H and K * Four Hermetically Sealed Package Configurations * Performance Guaranteed over -55C to +125C * Wide VCC Range (4.5 to 20 V) * 350 ns Maximum Propagation Delay * CMR: > 10,000 V/s Typical * 1500 Vdc Withstand Test Voltage * Three State Output Available * High Radiation Immunity * HCPL-2200/31 Function Compatibility * Reliability Data * Compatible with LSTTL, TTL, and CMOS Logic Applications * Military and Space * High Reliability Systems * Transportation and Life Critical Systems * High Speed Line Receiver * Isolated Bus Driver (Single Channel) * Pulse Transformer Replacement * Ground Loop Elimination * Harsh Industrial Environments * Computer-Peripheral Interfaces Description These units are single, dual and quad channel, hermetically sealed optocouplers. The products are capable of operation and storage over the full military temperature range and can be purchased as either standard product or with full MIL-PRF-38534 Class Level H or K testing or from the appropriate DESC Drawing. All devices are manufactured and tested on a MIL-PRF-38534 certified line and are included in the DESC Qualified Manufacturers List QML-38534 for Hybrid Microcircuits. eliminates the potential for output signal chatter. The detector in the single channel units has a tri-state output stage Truth Tables (Positive Logic) Multichannel Devices Input Output On (H) H Off (L) L Single Channel DIP Input Enable On (H) H Off (L) H On (H) L Off (L) L Output Z Z H L Functional Diagram Multiple Channel Devices Available VCC Each channel contains an AlGaAs light emitting diode which is optically coupled to an integrated high gain photon detector. The detector has a threshold with hysteresis which provides differential mode noise immunity and VO VE GND CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. 1-512 5965-3005E Package styles for these parts are 8 pin DIP through hole (case outline P), 16 pin DIP flat pack (case outline F), and leadless ceramic chip carrier (case outline 2). Devices may be purchased with a variety of lead bend and plating options, see Selection Guide Table for details. Standard Military drawing (SMD) parts are available for each package and lead style. Because the same electrical die (emitters and detectors) are used for each channel of each device listed in this data sheet, absolute maximum ratings, recommended operating conditions, electrical specifications, and performance characteristics shown in the figures are identical for all parts. Occasional exceptions exist due to package variations and limitations and are as noted. Additionally, the same package assembly processes and materials are used in all devices. These similarities give justification for the use of data obtained from one part to represent other part's performance for die related reliability and certain limited radiation test results. Selection Guide-Package Styles and Lead Configuration Options Package Lead Style Channels Common Channel Wiring HP Part # & Options Commercial MIL-PRF-38534, Class H MIL-PRF-38534, Class K Standard Lead Finish Solder Dipped Butt Cut/Gold Plate Gull Wing/Soldered SMD Part # Prescript for all below Either Gold or Solder Gold Plate Solder Dipped Butt Cut/Gold Plate Butt Cut/Soldered Gull Wing/Soldered 8 Pin DIP Through Hole 1 None 8 Pin DIP Through Hole 2 VCC, GND 16 Pin Flat Pack Unformed Leads 4 VCC, GND 20 Pad LCCC Surface Mount 2 None HCPL-5200 HCPL-5201 HCPL-520K Gold Plate Option #200 Option #100 Option #300 HCPL-5230 HCPL-5231 HCPL-523K Gold Plate Option #200 Option #100 Option #300 HCPL-6250 HCPL-6251 HCPL-625K Gold Plate HCPL-6230 HCPL-6231 HCPL-623K Soldered Pads 59628876801PX 8876801PC 8876801PA 8876801YC 8876801YA 8876801XA 59628876901PX 8876901PC 8876901PA 8876901YC 8876901YA 8876901XA 59628876903FX 8876903FC 596288769022X 88769022A 1-513 HERMETIC/HI-REL OPTOCOUPLERS which allows for direct connection to data buses. The output is noninverting. The detector IC has an internal shield that provides a guaranteed common mode transient immunity of up to 10,000 V/s. Improved power supply rejection eliminates the need for special power supply bypass precautions. Functional Diagrams 8 Pin DIP Through Hole 1 Channel 8 Pin DIP Through Hole 2 Channels 16 Pin Flat Pack Unformed Leads 4 Channels VCC VO 2 3 VE 4 GND 8 1 VCC 8 6 5 7 2 3 4 VO2 GND VCC2 2 VCC 15 3 VO1 14 4 VO2 13 5 VO3 12 2 6 VO4 11 3 7 GND 10 19 VO1 7 15 16 1 1 20 Pad LCCC Surface Mount 2 Channels 6 5 GND2 VO1 VCC1 12 10 GND1 7 9 8 13 VO2 20 8 Note: Multichannel DIP and flat pack devices have common VCC and ground. Single channel DIP has an enable pin 6. LCCC (leadless ceramic chip carrier) package has isolated channels with separate VCC and ground connections. 7.24 (0.285) 6.99 (0.275) Outline Drawings 2.29 (0.090) MAX. 16 Pin Flat Pack, 4 Channels 1.27 (0.050) REF. 11.13 (0.438) 10.72 (0.422) 0.46 (0.018) 0.36 (0.014) 8.13 (0.320) MAX. 2.85 (0.112) MAX. 0.88 (0.0345) MIN. 0.89 (0.035) 0.69 (0.027) 5.23 (0.206) MAX. 0.31 (0.012) 0.23 (0.009) 9.02 (0.355) 8.76 (0.345) NOTE: DIMENSIONS IN MILLIMETERS (INCHES). 20 Terminal LCCC Surface Mount, 2 Channels 8 Pin DIP Through Hole, 1 and 2 Channel 9.40 (0.370) 9.91 (0.390) 0.76 (0.030) 1.27 (0.050) 8.70 (0.342) 9.10 (0.358) 4.95 (0.195) 5.21 (0.205) 1.78 (0.070) 2.03 (0.080) 7.16 (0.282) 7.57 (0.298) 1.02 (0.040) (3 PLCS) 1.14 (0.045) 1.40 (0.055) 8.70 (0.342) 9.10 (0.358) 4.95 (0.195) 5.21 (0.205) TERMINAL 1 IDENTIFIER 2.16 (0.085) 4.32 (0.170) MAX. 0.51 (0.020) MIN. METALIZED CASTILLATIONS (20 PLCS) 1.78 (0.070) 2.03 (0.080) 0.64 (0.025) (20 PLCS) 3.81 (0.150) MIN. 0.20 (0.008) 0.33 (0.013) 0.51 (0.020) 1.52 (0.060) 2.03 (0.080) NOTE: DIMENSIONS IN MILLIMETERS (INCHES). SOLDER THICKNESS 0.127 (0.005) MAX. 1-514 8.13 (0.320) MAX. 2.29 (0.090) 2.79 (0.110) 0.51 (0.020) MAX. NOTE: DIMENSIONS IN MILLIMETERS (INCHES). 7.36 (0.290) 7.87 (0.310) HP LOGO HP P/N DESC SMD* DESC SMD* PIN ONE/ ESD IDENT HP QYYWWZ XXXXXX XXXXXXX XXX USA * 50434 Leadless Device Marking COMPLIANCE INDICATOR,* DATE CODE, SUFFIX (IF NEEDED) COUNTRY OF MFR. HP FSCN* HP LOGO HP P/N PIN ONE/ ESD IDENT COUNTRY OF MFR. HP QYYWWZ XXXXXX * XXXX XXXXXX USA 50434 COMPLIANCE INDICATOR,* DATE CODE, SUFFIX (IF NEEDED) DESC SMD* DESC SMD* HP FSCN* *QUALIFIED PARTS ONLY *QUALIFIED PARTS ONLY Hermetic Optocoupler Options Option 100 Description Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is available on commercial and hi-rel product in 8 pin DIP (see drawings below for details). 4.32 (0.170) MAX. 0.51 (0.020) MIN. 2.29 (0.090) 2.79 (0.110) 1.14 (0.045) 1.40 (0.055) 0.20 (0.008) 0.33 (0.013) 0.51 (0.020) MAX. 7.36 (0.290) 7.87 (0.310) NOTE: DIMENSIONS IN MILLIMETERS (INCHES). 200 300 Lead finish is solder dipped rather than gold plated. This option is available on commercial and hi-rel product in 8 pin DIP. DESC Drawing part numbers contain provisions for lead finish. All leadless chip carrier devices are delivered with solder dipped terminals as a standard feature. Surface mountable hermetic optocoupler with leads cut and bent for gull wing assembly. This option is available on commercial and hi-rel product in 8 pin DIP (see drawings below for details). This option has solder dipped leads. 5.57 (0.180) MAX. 0.51 (0.020) MIN. 2.29 (0.090) 2.79 (0.110) 1.40 (0.055) 1.65 (0.065) 5 MAX. 0.51 (0.020) MAX. 5.57 (0.180) MAX. 0.20 (0.008) 0.33 (0.013) 9.65 (0.380) 9.91 (0.390) NOTE: DIMENSIONS IN MILLIMETERS (INCHES). 1-515 HERMETIC/HI-REL OPTOCOUPLERS Leaded Device Marking Absolute Maximum Ratings Storage Temperature Range, TS .................................. -65C to +150C Operating Temperature, TA ......................................... -55C to +125C Case Temperature, TC ................................................................ +170C Junction Temperature, TJ ................................................................................... +175C Lead Solder Temperature .............................................. 260C for 10 s Average Forward Curre, IF AVG (each channel) ............................. 8 mA Peak Input Current, IF PK (each channel) ............................... 20 mA[1] Reverse Input Voltage, VR (each channel) ....................................... 3 V Supply Voltage ,VCC .............................................. 0.0 V min., 20 V max. Average Output Current, IO (each channel) ................................. 15 mA Output Voltage, VO (each channel) .................... -0.3 V min., 20 V max. Package Power Dissipation, Pd (each channel) ......................... 200 mW Single Channel Product Only Tri-State Enable Voltage, VE ............................... -0.3 V min., 20 V max. 8 Pin Ceramic DIP Single Channel Schematic ANODE CATHODE Note enable pin 6. An external 0.01 F to 0.1 F bypass capacitor is recommended between VCC and ground for each package type. ESD Classification (MIL-STD-883, Method 3015) HCPL-5200/01, HCPL-6230/31 ........................................... (), Class 1 HCPL-5230/31, HCPL-6250/51 ....................................... (Dot), Class 3 Recommended Operating Conditions Parameter Power Supply Voltage Input Current, High Level, Each Channel Input Voltage, Low Level, Each Channel Fan Out (TTL Load) Each Channel Symbol VCC IFH Min. 4.5 2 Max. 20 8 Units V mA VFL 0 0.8 V N Single Channel Product Only High Level Enable Voltage VEH Low Level Enable Voltage VEL 1-516 4 2.0 0 20 0.8 V V TA = -55C to +125C, 4.5 V VCC 20 V, 2 mA IF(ON) 8 mA, 0 V VF(OFF) 0.8 V, unless otherwise specified. Test Conditions Group A[11] Limit Subgroups Min. Typ.* Max. Units Fig. Notes Parameter Sym. Logic Low Output Voltage VOL IOL = 6.4 mA (4 TTL Loads) 1, 2, 3 1, 2, 3 Logic High Output Voltage VOH IOH = -2.6 mA (**VOH = VCC - 2.1 V) Output Leakage Current IOHH IOH = -0.32 mA (VOUT > VCC) Logic Low Supply Current Single Channel 0.5 2.4 NA VO = 5.5 V IF = 8 mA VO = 20 V VCC = 4.5 V VCC = 5.5 V VF = 0 V V = 20 V VE = Don't Care CC ** V 1, 3 2 2, 3 2 V 3.1 1, 2, 3 100 A 2 500 1, 2, 3 4.5 6 5.3 7.5 9.0 12 10.6 15 14 24 ICCL Dual Channel VCC = 5.5 V VCC = 20 V Quad Channel VCC = 5.5 V VF1 = VF2 = VF3 = VF4 = 0 V VCC = 20 V Single Channel VCC = 5.5 V IF = 8 mA VE = Don't Care VCC = 20 V Logic High Supply Current Dual Channel mA VF1 = VF2 = 0 V 17 30 2.9 4.5 3.3 6 5.8 9 6.6 12 9 18 11 24 1, 2, 3 ICCH VCC = 5.5 V VCC = 20 V Quad Channel IF1 = IF2 = 8 mA VCC = 5.5 V IF1 = IF2 = = V = 20 V IV VF3= = VF4 = 8 mA CC F3 F3 mA IF4 = 8 mA Logic Low Short Circuit Output Current VO = VCC = 5.5 V 20 VF = 0 V IOSL VO = VCC = 20 V Logic High Short Circuit Output Current VCC = 5.5 V IOSH VCC = 20 V 2, 3 35 IF = 8 mA VO = GND -10 1, 2, 3 mA 2, 3 -25 VF IF = 8 mA 1, 2, 3 1.0 Input Reverse Breakdown Voltage BVR IR = 10 A 1, 2, 3 3 Input-Output Insulation Leakage Current II-O VI-O = 1500 Vdc, t = 5s RH = 45%, TA = 25C Input Forward Voltage mA 1, 2, 3 1.3 1 1.8 1.0 V 4 2 V 2 A 4, 5 Logic High Common Mode |CMH| IF = 2 mA, VCM = 50 VP-P Transient Immunity 9, 10, 11 1000 10,000 V/s 9 2, 6, 12 Logic Low Common Mode |CML| IF = 0 mA, VCM = 50 VP-P Transient Immunity 9, 10, 11 1000 10,000 V/s 9 2, 6, 12 Propagation Delay Time to Logic Low tPHL 9, 10, 11 173 350 ns 5, 6 2, 7 Propagation Delay Time to Logic High tPLH 9, 10, 11 118 350 ns 5, 6 2, 7 1-517 HERMETIC/HI-REL OPTOCOUPLERS Electrical Characteristics Electrical Characteristics Single Channel Product Only TA = -55C to +125C, 4.5 V VCC 20 V, 2 mA IF (ON) 8 mA, 0 V VF(OFF) 0.8 V, 2.0 V VEH 20 V, 0 V VEL 0.8 V, unless otherwise specified. Parameter Sym. High Impedance State Output Current IOZL IOZH Test Conditions VO = 0.4 V VEN = 2 V, VF = 0 V VO = 2.4 V VEN = 2 V, IF = 8 mA VO = 5.5 V Group A[11] Subgroups Limits Min. Typ.* Max. Units 1, 2, 3 -20 A 20 A 1, 2, 3 100 VO = 20 V VEH 1, 2, 3 Logic Low Enable Voltage VEL 1, 2, 3 2.0 VEN = 5.5 V 1, 2, 3 IEL VEN = 0.4 V 0.8 V 20 A 100 VEN = 20 V Logic Low Enable Current V VEN = 2.7 V IEH Notes 500 Logic High Enable Voltage Logic High Enable Current Fig. 0.004 1, 2, 3 250 -0.32 mA *All typical values are at VCC = 5 V, TA = 25C, IF(ON) = 5 mA unless otherwise specified. Typical Characteristics All typical values are at TA = 25C, VCC = 5 V, IF(ON) = 5 mA unless otherwise specified. Parameter Input Current Hysteresis Input Diode Temperature Coefficient Resistance (Input-Output) Capacitance (Input-Output) Input Capacitance Output Rise Time (10-90%) Output Fall Time (90-10%) 1-518 Symbol Typ. IHYS 0.07 VF ---- -1.25 TA RI-O 1013 CI-O 2.0 CIN 20 tr 45 tf 10 Units mA Test Conditions VCC = 5 V mV/C IF = 8 mA pF pF ns ns Fig. 3 Notes 2 2 VI-O = 500 Vdc f = 1 MHz VF = 0 V, f = 1 MHz 5, 7 5, 7 2, 8 2, 8 2, 10 2 2 HERMETIC/HI-REL OPTOCOUPLERS Typical Characteristics (cont'd.) All typical values are at TA = 25C, VCC = 5 V, IF(ON) = 5 mA, unless otherwise specified. Single Channel Product Only Parameter Symbol Typ. Units Test Conditions Fig. Notes Output Enable Time to Logic High tPZH 30 ns 8 Output Enable Time to Logic Low tPZL 30 ns 8 Output Disable Time from Logic High tPHZ 45 ns 8 Output Disable Time from Logic Low tPLZ 55 ns 8 II-I 0.5 nA RH = 45%, TA = 25C, VI-I = 500 V, t = 5 s Resistance (Input-Input) RI-I 1013 VI-I = 500 V 9 Capacitance (Input-Input) CI-I 1.5 pF f = 1 MH 9 Dual and Quad Channel Products Only Input-Input Insulation Leakage Current 9 Notes: 1. Peak Forward Input Current pulse width < 50 s at 1 KHz maximum repetition rate. 2. Each channel of a multichannel device. 3. Duration of output short circuit time not to exceed 10 ms. 4. All devices are considered two-terminal devices: measured between all input leads or terminals shorted together and all output leads or terminals shorted together. 5. This is a momentary withstand test, not an operating condition. 6. CML is the maximum rate of rise of the common mode voltage that can be sustained with the output voltage in the logic low state (VO < 0.8 V). CMH is the maximum rate of fall of the common mode voltage that can be sustained with the output voltage in the logic high state (VO > 2.0 V). 7. tPHL propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the leading edge of the output pulse. The tPLH propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.3 V point on the trailing edge of the output pulse. 8. Measured between each input pair shorted together and all output connections for that channel shorted together. 9. Measured between adjacent input pairs shorted together for each multichannel device. 10. Zero-bias capacitance measured between the LED anode and cathode. 11. Standard parts receive 100% testing at 25C (Subgroups 1 and 9). SMD and hi-rel parts receive 100% testing at 25, 125, and -55C (Subgroups 1 and 9, 2 and 10, 3 and 11, respectively). 12. Parameters are tested as part of device initial characterization and after design and process changes. Parameters guaranteed to limits specified for all lots not specifically tested. Figure 1. Typical Logic Low Output Voltage vs. Temperature. Figure 2. Typical Logic High Output Current vs. Temperature. 1-519 Figure 3. Output Voltage vs. Forward Input Current. Figure 4. Typical Diode Input Forward Characteristic. VCC PULSE GEN. tr = tf = 5 ns t = 100 kHz 10 % DUTY CYCLE OUTPUT VO MONITORING NODE D.U.T. VCC IF INPUT MONITORING NODE Rf D1 VO VE 5V D2 CL= 15 pF GND 619 5K D3 D4 THE PROBE AND JIG CAPACITANCES ARE INCLUDED IN CL. Figure 5. Test Circuit for tPLH, tPHL, tr, and tf. Figure 6. Typical Propagation Delay vs. Temperature. 1-520 Figure 7. Typical Rise, Fall Time vs. Temperature. CL= 15 pF INCLUDING PROBE AND JIG CAPACITANCE. HERMETIC/HI-REL OPTOCOUPLERS PULSE GENERATOR ZO = 50 tr = tf = 5 ns +5 V VCC VO D.U.T. S1 VCC IF D2 CL VE D1-4 ARE 1N916 OR 1N3064 619 D1 VO GND 5 K D3 D4 INPUT VO MONITORING NODE S2 Figure 8. Test Circuit for tPHZ, tPZH, tPLZ, and tPZL. A VCC D.U.T. B OUTPUT VO MONITORING NODE VCC RIN VO 0.1 F BYPASS VE VFF GND *SEE NOTE 6. VCM + - PULSE GEN. Figure 9. Test Circuit for Common Mode Transient Immunity and Typical Waveforms. VCC1 (+5 V) VCC2 (4.5 TO 20 V) 665 D.U.T. VCC DATA INPUT RL VO CMOS TTL OR LSTTL 1 VCC1 (+5 V) 750 D.U.T. VE VCC GND TOTEM POLE OUTPUT GATE DATA OUTPUT VCC2 5V 10 V 15 V 20 V RL 1.1 K 2.37 K 3.83 K 5.11 K DATA INPUT 2 Figure 10. LSTTL to CMOS Interface Circuit. TTL OR LSTTL TOTEM POLE OUTPUT GATE GND Figure 11. Recommended LED Drive Circuit. 1-521 VCC1 (+5 V) 619 D.U.T. VCC 4.02 K DATA INPUT TTL OR LSTTL GND OPEN COLLECTOR GATE Figure 12. Series LED Drive with Open Collector Gate (4.02 k Resistor Shunts IOH from the LED). VCC2 (+5 V) DATA OUTPUT VCC1 (+5 V) 665 665 VCC DATA INPUT TTL OR LSTTL DATA INPUT TOTEM POLE OUTPUT GATE UP TO 16 LSTTL LOADS OR 4 TTL LOADS D.U.T. 0.1 F DATA OUTPUT TTL OR LSTTL GND 1 TOTEM POLE OUTPUT GATE UP TO 16 LSTTL LOADS OR 4 TTL LOADS 1 2 Figure 13. Recommended LSTTL to LSTTL Circuit. VCC + 20 V D.U.T.* VCC IF + IO - VIN 1.90 V 100 VE 0.01 F 1200 GND CONDITIONS: IF = 8 mA IO = -14 mA TA = +125 C *ALL CHANNELS TESTED SIMULTANEOUSLY. Figure 14. Single Channel Operating Circuit for Burn-in and Steady State Life Tests. 1-522 HERMETIC/HI-REL OPTOCOUPLERS MIL-PRF-38534 Class H, Class K, and DESC SMD Test Program Hewlett-Packard's Hi-Rel Optocouplers are in compliance with MIL-PRF-38534 Classes H and K. Class H devices are also in compliance with DESC drawings 5962-88768, and 5962-88769. Testing consists of 100% screening and quality conformance inspection to MIL-PRF-38534. 1-523