ABMJB-902-104USY-T5 - ABRACON

ABMJB-902

Low Power MEMS Jitter Attenuator

2.9 x 2.8 x 1.45 mm SOT23-6L

Moisture Sensitivity Level: MSL=1

Pb

RoHS/RoHS II Compliant

ESD Sensitive

CERTIFIED

ABRACON IS

CERTIFIED

ABRACON IS

ISO9001:2008

CERTIFIED

• Low power and miniature package programmable jitter attenuator

• Input/output frequency up to 200MHz

• I/O pins can be configured as output enable (OE), frequency switching (CSEL),

power down (PDB) input, or CLK1 (2) output.

• <10μA current consumption with PDB active

• Operating temperature range from -40˚C to +85˚C

• 6-pin SOT23 RoHS-compliant packages

• Related devices:

- ABMJB-903: Single-ended input, differential output, and phase noise cleaning

FEATURES: APPLICATIONS:

• IEEE1588 GPIO clock cleanup

• FPGA-generated clock cleanup

• 1/10/40/100 Gigabit Ethernet (GbE)

• SONET/SDH

• PCI-Express

• CPRI/OBSAI wireless base stations

• Fibre Channel

• SAS/SATA

• DIMM

STANDARD SPECIFICATIONS:

2 Faraday, Suite# B

|

Irvine

|

CA 92618

Revised: 03.09.15

Ph. 949.546.8000

|

Fax. 949.546.8001

Visit www.abracon.com for Terms and Conditions of Sale

LLC

Absolute Maximum Ratings

(1)

Parameters Min. Typ. Max. Units Notes

Supply Voltage (V

DD

) +4.6 V

Input Voltage (V

IN

) -0.5 V

DD

+0.5

V

s02 ,gniredloS Cº 062+ erutarepmeT daeL

Cº 511+ erutarepmeT esaC

Storage Temperature (T

S

) -65 +150 ºC

Operation Ratings

(2)

Parameters Min. Typ. Max. Units Notes

Supply Voltage (V

DD

) +2.25 +3.63 V

Junction Thermal Resistance (0

JA

) 195 ºC/W SOT23, Still-Air

Ambient Temperature (T

A

) -40 +85 ºC

DC Electrical Characteristics

V

DD

= 3.3V±10% or 2.5V±10%; CL = 15pF; T

A

= 25°C

Parameters Min. Typ. Max. Units Notes

Supply Current, dynamic (I

DD

) 12 18 mA

V

DD

= 3.3V, 30MHz, Load = 15pF

<10 µA

When PDB = 0

Operating Voltage (V

DD

) +2.25 +3.63 V

Power Supply Ramp (t

PU

) 0.001 100 ms

Time for V

DD

to reach 90%

V

DD

. Power

ramp must be monotonic.

Output Current, low drive (I

OLD

) 4 mA

V

OL

= 0.4V,

V

OH

=

V

DD

- 0.9V,

V

DD

=

3.3V

Output Current, standard drive (I

OSD

)

8 mA

Output Current, high drive (I

OHD

)

16 mA

Notes:

1. Exceeding the absolute maximum ratings may damage the device.

2. The device is not guaranteed to function outside tis operating ratings.

ABMJB-902

Low Power MEMS Jitter Attenuator

2.9 x 2.8 x 1.45 mm SOT23-6L

Pb

RoHS/RoHS II Compliant

ESD Sensitive

CERTIFIED

ABRACON IS

CERTIFIED

ABRACON IS

ISO9001:2008

CERTIFIED

2 Faraday, Suite# B

|

Irvine

|

CA 92618

Revised: 03.09.15

Ph. 949.546.8000

|

Fax. 949.546.8001

Visit www.abracon.com for Terms and Conditions of Sale

LLC

AC Electrical Characteristics

V

DD

= 3.3V±10% or 2.5V±10%; CL = 15pF; T

A

= 25°C

Parameters Min. Typ. Max. Units Notes

Input (REFIN)

Frequency

3.3V Operation

1 200 MHz

2.5V Operation

1 167

Input Signal Amplitude

0.8

V

DD

V

PP

Internally AC-coupled (high frequency)

0.1

V

DD

Internally AC-coupled (low frequency)

For 3.3V operation, F

REFIN

≤50MHz

For 2.5V operation, F

REFIN

≤40MHz

Output Frequency

5 200

MHz

CLK0 and CLK1, 3.3V operation

5 167

CLK0 and CLK1, 2.5V operation

1.25 200

CLK2, 3.3V operation

1.25 167

CLK2, 2.5V operation

sm 1 emiT gniltteS

At power up (after V

DD

increases over

2.25V)

Output Enable Time 10 ns

OE function: T

A

= 25°C, 15pF load. Add

one clock period to this measurement for

a usable clock output

1 ms

PDB function: T

A

= 25°C, 15pF load

Output Rise Time 1.2 1.7 ns

15pF load, 10/90% V

DD

, high drive, 3.3V

sn 7.1 2.1 emiT llaF tuptuO

15pF load, 10/90% V

DD

, high drive, 3.3V

% 55 05 54 elcyC ytuD

@2.5V and 3.3V over entire frequency

range. Threshold = V

DD

/2

Period Jitter (peak-to-peak)

(3)

75 ps

10,000 samples measured

Jitter Attenuation Bandwidth 4 kHz

CLK0 = REFIN

Notes:

3. Jitter performance can be considered the noise floor of the device. Jitter cannot be attenuated below this value.

Please refer to the ABMJB-902 Part Number and Configuration Guide for available part

numbers and configurations.

OPTIONS AND PART IDENTIFICATION:

OUTLINE DIMENSION:

ABMJB-902

Low Power MEMS Jitter Attenuator

2.9 x 2.8 x 1.45 mm SOT23-6L

Pb

RoHS/RoHS II Compliant

ESD Sensitive

CERTIFIED

ABRACON IS

CERTIFIED

ABRACON IS

ISO9001:2008

CERTIFIED

2 Faraday, Suite# B

|

Irvine

|

CA 92618

Revised: 03.09.15

Ph. 949.546.8000

|

Fax. 949.546.8001

Visit www.abracon.com for Terms and Conditions of Sale

LLC

Notes:

1. Dimensions and tolerances are as per ANSI Y14.5M, 1982

2. Package surface to be mirror finish.

3. Die is facing up for mold. Die is facing down for trim/form. i.e.

reverse trim/form.

4. The foot length measuring is based on the gauge plane method.

5 Dimensions are exclusive of mold flash & gate burr.

Dimension: mm

Pin No. Configuration

1 PDB, OE, CLK1

2 GND

3 REFIN

4 VDD

5 CSEL, CLK2

6 CLK0

PIN DESCRIPTION:

ABMJB-902

Low Power MEMS Jitter Attenuator

2.9 x 2.8 x 1.45 mm SOT23-6L

Pb

RoHS/RoHS II Compliant

ESD Sensitive

CERTIFIED

ABRACON IS

CERTIFIED

ABRACON IS

ISO9001:2008

CERTIFIED

2 Faraday, Suite# B

|

Irvine

|

CA 92618

Revised: 03.09.15

Ph. 949.546.8000

|

Fax. 949.546.8001

Visit www.abracon.com for Terms and Conditions of Sale

LLC

SOT23-6L package

Pin No. Pin Name Pin Type Pin Level Function

1 PDB, OE, CLK1 I/O LVCMOS Customizable pin: power down or output enable control

input with pull-up or clock output

2 GND GND Power supply ground

3 REF_IN I, (SE) LVCMOS Reference clock input

4 VDD PWR Power supply

5 CSEL, CLK2 I/O LVCMOS Customizable pin: configuration select control input with

pull-up or clock output

6 CLK0 O LVCMOS Clock output

BLOCK DIAGRAM:

Clock Output (CLK0)

Clock Output (CLK1, CLK2)

Output Enable (OE)

Power Down Control (PDB)

Configuration Select (CSEL)

ABMJB-902

Low Power MEMS Jitter Attenuator

2.9 x 2.8 x 1.45 mm SOT23-6L

Pb

RoHS/RoHS II Compliant

ESD Sensitive

CERTIFIED

ABRACON IS

CERTIFIED

ABRACON IS

ISO9001:2008

CERTIFIED

2 Faraday, Suite# B

|

Irvine

|

CA 92618

Revised: 03.09.15

Ph. 949.546.8000

|

Fax. 949.546.8001

Visit www.abracon.com for Terms and Conditions of Sale

LLC

The ABMJB-902 series is a highly featured, very flexible, advanced programmable jitter filter design for high

performance, low-power, small form-factor applications. The ABMJB-902 accepts a reference clock input between

1MHz and 200MHz and is capable of producing up to three outputs in the 5MHz to 200MHz range. The most common

configuration will be comprised of the same input and output frequency, but this flexible design also allows frequency

translation from one frequency to another frequency as long as both frequencies are within the specified ranges for input

and output.

Jitter Filter Programming

Typically, the jitter filter settings will be optimized for one particular input and output frequency, but the flexible design

also allows configurations for a certain frequency range, up to one octave wide.

The typical bandwidth of the jitter filter is 4kHz. This means that jitter frequency components above 4kHz will be

attenuated. In case of frequency translation, the bandwidth may be slightly different.

Clock Output (CLK0)

CLK0 is the main clock output. The output drive level can be programmed to low drive (4mA), standard drive (8mA) or

high drive (16mA). The maximum output frequency is 200MHz at 3.3V operation and 167MHz at 2.5V operation.

Clock Output (CLK1, CLK2)

The CLK1 and CLK2 feature allows the PL902xxx to have two additional clock outputs programmed to one of the

following frequencies:

• CLK1 = CLK0

• CLK2 = CLK0, CLK0/2 or CLK0/4

CLK1 and CLK2 allow the same output drive level programming as CLK0. Because of the extra /2 and /4 settings,

CLK2 is capable of going down to 1.25MHz. In case only an output clock of <5MHz is needed, CLK0 and CLK1 can be

disabled.

Output Enable (OE)

The output enable feature allows the user to enable and disable the clock output(s) by toggling the OE pin. The OE pin

incorporates a 60kΩ pull-up resistor, giving a default condition of logic “1”.

Power Down Control (PDB)

The power down (PDB) feature allows the user to put the ABMJB-902 into sleep mode. When activated (logic “0”),

PDB disables the synthesizer circuitry, counters, and all other active circuitry. In power down mode, the IC consumes

<10µA of power. The PDB pin incorporates a 60kΩ pull-up resistor giving a default condition of logic “1”.

Configuration Select (CSEL)

The configuration select (CSEL) feature allows the PL902xxx to switch between two pre-programmed configurations

allowing the device on-the-fly frequency switching. The CSEL pin incorporates a 60kΩ pull-up resistor giving a default

condition of logic “1”.

Examples for this feature are:

• Select between two frequencies or two frequency ranges.

• Select between two frequency translations, like 1:1 and 1:2.

FUNCTIONAL DESCRIPTION

Pb

RoHS/RoHS II Compliant

ESD Sensitive

CERTIFIED

ABRACON IS

CERTIFIED

ABRACON IS

ISO9001:2008

CERTIFIED

KEY PROGRAMMING PARAMETERS:

2 Faraday, Suite# B

|

Irvine

|

CA 92618

Revised: 03.09.15

Ph. 949.546.8000

|

Fax. 949.546.8001

Visit www.abracon.com for Terms and Conditions of Sale

LLC

CLK[0:2]

Output Frequency Output Drive Strength Programmable

Input/Output

CLK0 = REFIN

CLK1 = CLK0

CLK2 = CLK0, CLK0/2, or CLK0/4

Frequency translation is optional

within the specified frequency range.

Three optional drive strengths to

choose from:

• Low: 4mA

• Standard: 8mA (default)

• High: 16mA

One output pin can be configured as:

• OE – input

• PDB – input

• CSEL – input

• CLK1, 2 – output

The following guidelines are designed to assist the user to create a performance-optimized PCB design.

Signal Integrity and Termination Considerations

Keep traces short for good signal integrity.

Trace = Inductor. With a capacitive load this causes ringing.

Long trace = Transmission line. Without proper termination, this will cause reflections that also look like ringing.

Design long traces (greater than 1 inch) as “striplines” or “microstrips” with defined impedance.

Match the trace at one side to avoid reflections bouncing back and forth.

Decoupling and Power Supply Considerations

Place decoupling capacitors as close as possible to the VDD pin(s) to limit noise from the power supply.

Multiple VDD pins should be decoupled separately for best performance.

The addition of a ferrite bead in series with VDD can help prevent noise from other board sources.

The value of the decoupling capacitor is frequency-dependent. Typical values to use are 0.1µF for designs using

frequencies <50MHz and 0.01µF for designs using frequencies >50MHz.

LAYOUT RECOMMENDATIONS

ABMJB-902

Low Power MEMS Jitter Attenuator

2.9 x 2.8 x 1.45 mm SOT23-6L

PERIOD JITTER HISTOGRAM

Pb

RoHS/RoHS II Compliant

ESD Sensitive

CERTIFIED

ABRACON IS

CERTIFIED

ABRACON IS

ISO9001:2008

CERTIFIED

2 Faraday, Suite# B

|

Irvine

|

CA 92618

Revised: 03.09.15

Ph. 949.546.8000

|

Fax. 949.546.8001

Visit www.abracon.com for Terms and Conditions of Sale

LLC

10MHz input clock with bad period jitter - 460pcs peak-to-peak period jitter

ABMJB-902

Low Power MEMS Jitter Attenuator

2.9 x 2.8 x 1.45 mm SOT23-6L

10MHz output clock from Jitter Attenuator - 75pcs peak-to-peak period jitter

Pb

RoHS/RoHS II Compliant

ESD Sensitive

CERTIFIED

ABRACON IS

CERTIFIED

ABRACON IS

ISO9001:2008

CERTIFIED

2 Faraday, Suite# B

|

Irvine

|

CA 92618

Revised: 03.09.15

Ph. 949.546.8000

|

Fax. 949.546.8001

Visit www.abracon.com for Terms and Conditions of Sale

LLC

FIXING EXTREME JITTER IN 10MHZ IEEE1588 GPIO CLOCKS

10MHZ clock from IEEE1588:

Jitter Attenuator Output Clock:

ABMJB-902

Low Power MEMS Jitter Attenuator

2.9 x 2.8 x 1.45 mm SOT23-6L

An IEEE1588 system can manufacture a 10MHz clock from 8ns pulses, but this creates extreme period jitter of

about 24ns peak-to-peak in this case. The Jitter Attenuator cleans that up to 100ps peak-to-peak, allowing the clock to

be used in more jitter-sensitive applications.

Pb

RoHS/RoHS II Compliant

ESD Sensitive

CERTIFIED

ABRACON IS

CERTIFIED

ABRACON IS

ISO9001:2008

CERTIFIED

REFLOW PROFILE:

TAPE & REEL:

Dimensions: mm

ATTENTION: Abracon Corporation’s products are COTS – Commercial-Off-The-Shelf products; suitable for Commercial, Industrial and, where designated, Automotive Applica-

tions. Abracon’s products are not specifically designed for Military, Aviation, Aerospace, Life-dependant Medical applications or any application requiring high reliability where

component failure could result in loss of life and/or property. For applications requiring high reliability and/or presenting an extreme operating environment, written consent and

authorization from Abracon Corporation is required. Please contact Abracon Corporation for more information.

2 Faraday, Suite# B

|

Irvine

|

CA 92618

Revised: 03.09.15

Ph. 949.546.8000

|

Fax. 949.546.8001

Visit www.abracon.com for Terms and Conditions of Sale

LLC

Parameters Specifications

Average Ramp-up Rate 3°C /second max.

Pre-Heat Temp 150 – 200°C 60 – 180 second

Temp > 217°C 60 – 150 second

Time @ Peak Temperature 20 – 40 second

Peak Temperature 260°C + 0°C / -5°C

Ramp-down Rate -6°C / second max.

Time 25°C to Peak Temp. 8 minutes max.

Packaging:

T: 3000pcs/reel

T5: 500pcs/reel

ABMJB-902

A H T W

Ø178±1.0

Ø60.0±1.0

1.5±0.3

8.4+0.0/-0.4

Low Power MEMS Jitter Attenuator

2.9 x 2.8 x 1.45 mm SOT23-6L