SPEC NO: DSAK2452 REV NO: V.1 DATE: DEC/21/2009 PAGE: 1 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen ERP: 1201005947
2.8X0.8mm RIGHT ANGLE SMD CHIP LED
LAMP
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Part Number: AA2810AZGS/G Green
Features
z2.8mmX0.8mm right angle SMT LED, 1.2mm thickness.
zLow power consumption.
zIdeal for backlight and indicator.
zVarious colors and lens types available.
zPackage : 2000pcs / reel.
zMoisture sensitivity level : level 3.
zRoHS compliant.
Description
The Green source color devices are made with InGaN Light
Emitting Diode.
Static electricity and surge damage the LEDS.
It is recommended to use a wrist band or anti-electrostatic
glove when handling the LEDs.
All devices, equipment and machinery must be electrically
grounded.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.0039") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAK2452 REV NO: V.1 DATE: DEC/21/2009 PAGE: 2 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen ERP: 1201005947
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might leads to damage and premature failure of the LED.
Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
SPEC NO: DSAK2452 REV NO: V.1 DATE: DEC/21/2009 PAGE: 3 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen ERP: 1201005947
Selection Guide
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
Absolute Maximum Ratings at TA=25°C
Electrical / Optical Characteristics at TA=25°C
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
Part No. Dice Lens Type
V
iewing
Angle [1]
Min. Typ. 2θ1/2
AA2810AZGS/G Green (InGaN) WATER CLEAR 900 1500 110°
Iv (mcd) [2]
@ 20mA
Symbol Parameter Device Typ. Max. Units Test Conditions
λpeak Peak Wavelength Green 520 nm IF=20mA
λD [1] Dominant Wavelength Green 525 nm IF=20mA
Δλ1/2 Spectral Line Half-width Green 35 nm IF=20mA
C Capacitance Green 100 pF VF=0V;f=1MHz
VF [2] Forward Voltage Green 3.2 4 V IF=20mA
IR Reverse Current Green 10 uA VR=5V
Parameter Green Units
Power dissipation 120 mW
DC Forward Current 30 mA
Peak Forward Current [1] 100 mA
Reverse Voltage 5 V
Operating Temperature -40°C To +85°C
Storage Temperature -40°C To +85°C
SPEC NO: DSAK2452 REV NO: V.1 DATE: DEC/21/2009 PAGE: 4 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen ERP: 1201005947
Green AA2810AZGS/G
SPEC NO: DSAK2452 REV NO: V.1 DATE: DEC/21/2009 PAGE: 5 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen ERP: 1201005947
AA2810AZGS/G
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAK2452 REV NO: V.1 DATE: DEC/21/2009 PAGE: 6 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen ERP: 1201005947
PACKING & LABEL SPECIFICATIONS AA2810AZGS/G