CCM-PFC ICE3PCS03G Standalone Power Factor Correction (PFC) Controller in Continuous Conduction Mode (CCM) Product Highlights * * * * * * * High efficiency over the whole load range Lowest count of external components Accurate and adjustable switching frequency Integrated digital voltage loop compensation Fast output dynamic response during load jump External synchronization Low peak current limitation ICE3PCS03G PG-DSO-8 Features Description * * * The ICE3PCS03G is a 8-pins wide input range controller IC for active power factor correction converters. It is designed for converters in boost topology, and requires few external components. Its power supply is recommended to be provided by an external auxiliary supply which will switch on and off the IC. * * * * Continuous current operation mode PFC Wide input range of Vcc up to 25V Enhanced dynamic response without input current distortion Accurate brown-out protection threshold External current loop compensation for greater user flexibility Open loop protection Maximum duty cycle of 95% (typical) DBYP DB L Boos t 90 ~ 270 Vac RGATE Line Filter CE RSHUNT R BVS 1 CB RGS RBVS 2 RBVS 3 DBRO1 DBRO2 RCS RBRO1 ISENSE RBRO2 GATE VSENSE BOP RBRO3 CBRO GND FREQ RFREQ Type Package ICE3PCS03G PG-DSO-8 Version 3.0 1 ICOMP VCC CICOMP CVCC V CC 03 April 2017 CCM-PFC ICE3PCS03G 1 1.1 1.2 Pin Configuration and Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 3.1 3.2 3.3 3.4 3.4.1 3.4.2 3.5 3.5.1 3.5.2 3.6 3.6.1 3.6.2 3.6.3 3.7 3.8 3.8.1 3.8.2 3.8.3 3.8.4 3.9 3.10 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Frequency Setting and External Synchronization . . . . . . . . . . . . . . . . . . . . . 6 Frequency Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 External Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Voltage Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Notch Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Voltage Loop Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Average Current Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Complete Current Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Current Loop Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Pulse Width Modulation (PWM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 PWM Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 System Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Input Voltage Brownout Protection(BOP) . . . . . . . . . . . . . . . . . . . . . . . . . 9 Peak Current Limit (PCL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Open Loop Protection (OLP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 First Over-Voltage Protection (OVP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Output Gate Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Protection Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4 4.1 4.2 4.3 4.3.1 4.3.2 4.3.3 4.3.4 4.3.5 4.3.6 4.3.7 4.3.8 4.3.9 4.3.10 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Supply Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Variable Frequency Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 PWM Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 External Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 PFC Brownout Protection Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 System Protection Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Current Loop Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Voltage Loop Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Driver Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Gate Drive Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5 Outline Dimension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Version 3.0 2 03 April 2017 CCM-PFC ICE3PCS03G Pin Configuration and Functionality 1 Pin Configuration and Functionality 1.1 Pin Configuration Pin Symbol Function 1 ISENSE Current Sense Input 2 GND 3 ICOMP 4 FREQ 5 BOP Brownout Protection 6 VSENSE Bulk Voltage Sense 7 VCC IC Supply Voltage 8 GATE Gate Drive ratings. Therefore a series resistor (RCS) of around 50 is recommended in order to limit this current into the IC GND (IC Ground) The ground potential of the IC. ICOMP (Current Loop Compensation) Low pass filter and compensation of the current control loop. The capacitor which is connected at this pin integrates the output current of OTA6 and averages the current sense signal. IC Ground Current Loop Compensation Switching Frequency Setting FREQ (Frequency Setting) This pin allows the setting of the operating switching frequency by connecting a resistor to ground. The frequency range is from 21kHz to 100kHz. BOP (Brownout Protection) BOP monitors the AC input voltage for Brownout Protection. Package PG-DSO-8 VSENSE VSENSE is connected via a resistive divider to the bulk voltage. The voltage of VSENSE relative to GND represents the output voltage. The bulk voltage is monitored for voltage regulation, over voltage protection and open loop protection. GATE ISENSE GND VCC VCC VCC provides the power supply of the ground related to IC section. P-DSO-8 VSENSE ICOMP FREQ BOP GATE GATE is the output for driving the PFC MOSFET.Its gate drive voltage is clamped at 15V (typically). Figure 1 1.2 Pin Configuration (top view) Pin Functionality ISENSE (Current Sense Input) The ISENSE Pin senses the voltage drop at the external sense resistor (RSHUNT). This is the input signal for the average current regulation in the current loop. It is also fed to the peak current limitation block. During power up time, high inrush currents cause high negative voltage drop at RSHUNT, driving currents out of pin 1 which could be beyond the absolute maximum Version 3.0 3 03 April 2017 Figure 2 Version 3.0 4 R BRO3 R BRO2 R BRO1 D BRO2 Line Filter CBRO CE RShunt R CS QB RFREQ FREQ R GATE GATE BOP Oscillator/ Synchronization PWM Logic Driver Brownout Protection ICE3PCS03G CISENSE C ICOMP ICOMP GND Nonlinear Gain Current Loop Compensation/ PCL ISENSE Voltage Loop Compensation VCC Unit Ramp Generator Protection Unit DB VSENSE VCC Auxiliary Supply R BVS3 CB R BVS2 R BVS1 2 D BRO1 90 ~ 270 Vac LBoost D BYP CCM-PFC ICE3PCS03G Block Diagram Block Diagram A functional block diagram is given in Figure 2. Note that the figure only shows the brief functional block and does not represent the implementation of the IC. Block Diagram 03 April 2017 CCM-PFC ICE3PCS03G Block Diagram Table 1 Bill of Material Component Parameters Rectifier Bridge GBU8J CE 100nF/X2/275V LBoost 750uH QB IPP60R199CP DBYP MUR360 DB IDT04S60C CB 220F/450V DBRO1...2 1N4007 RBRO1...2 3.9M RBRO3 130k CBRO 3F Rshunt 60m Cisense 1nF RCS 50 RGATE 3.3 RFREQ 67k CICOMP 4.7nF/25V RBVS1...2 1.5M RBVS3 18.85k Version 3.0 5 03 April 2017 CCM-PFC ICE3PCS03G Functional Description 3 3.1 Functional Description VBULK 100% 95% General 20% VCC The ICE3PCS03G is a 8-pins control IC for power factor correction converters. It is suitable for wide range line input applications from 85 to 265 VAC with overall efficiency above 90%. The IC supports converters in boost topology and it operates in continuous conduction mode (CCM) with average current control. The IC operates with a cascaded control; the inner current loop and the outer voltage loop. The inner current loop of the IC controls the sinusoidal profile for the average input current. It uses the dependency of the PWM duty cycle on the line input voltage to determine the corresponding input current. This means the average input current follows the input voltage as long as the device operates in CCM. Under light load condition, depending on the choke inductance, the system may enter into discontinuous conduction mode (DCM) resulting in a higher harmonics but still meeting the Class D requirement of IEC 1000-3-2. The outer voltage loop controls the output bulk voltage, integrated digitally within the IC. Depending on the load condition, internal PI compensation output is converted to an appropriate DC voltage which controls the amplitude of the average input current. The IC is equipped with various protection features to ensure safe operating condition for both the system and device. 3.2 26V 12V IVCC <6.4mA with 1nF external cap. at gate drive pin UVLO Figure 3 3.3 Bulk voltage rises to 95% rated value within 200ms Normal operation Standby mode (V VSENSE < 0.5V) State of Operation respect to VCC Start-up During power up when the Vout is less than 95% of the rated level, internal voltage loop output increases from initial voltage under the soft-start control. This results in a controlled linear increase of the input current from 0A thus reducing the stress in the external components. Once Vout has reached 95% of the rated level, the softstart control is released to achieve good regulation and dynamic response. 3.4 Power Supply Frequency Setting and External Synchronization The IC can provide external switching frequency setting by an external resistor RFREQ and the online synchronization by external pulse signal at FREQ pin. An internal under voltage lockout (UVLO) block monitors the VCC power supply. As soon as it exceeds 12.0V and both voltages at pin 6 (VSENSE) >0.5V and pin 5 (BOP) >1.25V, the IC begins operating its gate drive and performs its startup as shown in Figure 3. If VCC drops below 11V, the IC is off. The IC will then be consuming typically 1.4mA, whereas consuming 6.4mA during normal operation The IC can be turned off and forced into standby mode by pulling down the voltage at pin 6 (VSENSE) below 0.5V. Version 3.0 3.5mA 1.4mA 3.4.1 Frequency Setting The switching frequency of the PFC converter can be set with an external resistor RFREQ at FREQ pin as shown Figure 2. The pin voltage at VFREQ is typical 1V. The corresponding capacitor for the oscillator is integrated in the device and the RFREQ/frequency is given in Figure 4. The recommended operating frequency range is from 21kHz to 100kHz. As an example, a RFREQ of 67k at pin FREQ will set a switching frequency FSW of 65kHz typically. 6 03 April 2017 CCM-PFC ICE3PCS03G Functional Description 3.5 Voltage Loop The voltage loop is the outer loop of the cascaded control scheme which controls the PFC output bus voltage VOUT. This loop is closed by the feedback sensing voltage at VSENSE which is a resistive divider tapping from VOUT. The pin VSENSE is the input of sigma-delta ADC which has an internal reference of 2.5V and sampling rate of 3.55kHz (typical). The voltage loop compensation is integrated digitally for better dynamic response and saving design effort. Figure 6 shows the important blocks of this voltage loop. L Boost Figure 4 DB R BVS1 Frequency Versus RFREQ QB Rectified Input Voltage 3.4.2 External Synchronization The switching frequency can be synchronized to the external pulse signal after 6 external pulses delay once the voltage at the FREQ pin is higher than 2.5V. The synchronization means two points. Firstly, the PFC switching frequency is tracking the external pulse signal frequency. Secondly, the falling edge of the PFC signal is triggered by the rising edge of the external pulse signal. Figure 5 shows the blocks of frequency setting and synchronization. The external RSYN combined with RFREQ and the external diode DSYN can ensure pin voltage to be kept between 1.0V (clamped externally) and 5V (maximum pin voltage). If the external pulse signal has disappeared longer than 108s (typical) the switching frequency will be synchronized to internal clock set by the external resistor RFREQ. R GATE R BVS2 CB R BVS3 Gate Driver Current Loop + PWM Generation GATE VIN Av(IIN ) Nonlinear Gain Sigmadelta ADC Notch Filter PI Filter 2.5V VSENSE t 500 ns OLP C2 a C1 a OVP OVP Q R Q S 0.5V 2.5V 2.7V C1 b Syn. clock IOSC Figure 6 1.0V DSYN OTA7 3.5.1 Notch Filter In the PFC converter, an averaged current through the output diode of rectified sine waveform charges the output capacitor and results in a ripple voltage at the output capacitor with a frequency two times of the line frequency. In this digital PFC, a notch filter is used to remove the ripple of the sensed output voltage while keeping the rest of the signal almost uninfluenced. In this way, an accurate and fast output voltage regulation without influence of the output voltage ripple is achieved. RSYN C9 RFREQ FREQ Figure 5 Version 3.0 Voltage Loop SYN 2.5V/1.25V 3.5.2 Voltage Loop Compensation The Proportion-Integration (PI) compensation of the voltage loop is integrated digitally inside the IC. The digital data out of the PI compensator is converted to analog voltage for current loop control. Frequency Setting and Synchronization 7 03 April 2017 CCM-PFC ICE3PCS03G Functional Description The nonlinear gain block controls the amplitude of the regulated inductor current. The input of this block is the output voltage of integrated PI compensator. This block has been designed to reduce the voltage loop dependency on the input voltage in order to support the wide input voltage range (85VAC-265VAC). Figure 7 gives the relative output power transfer curve versus the digital word from the integrated PI compensator. The output power at the input voltage of 85VAC and maximum digital word of 256 from PI compensator is set as the normative power and the power curves at different input voltage present the relative power to the normative one. power at 85V LBoost Rectified Input Voltage RGATE CB Rshunt GATE RCS Current Loop ISENSE power at 265V Current Loop Compensation ICOMP 10.00000 1.00000 relative output power DB QB CICOMP OTA6 voltage proportional to averaged Inductor current Gate Driver PWM Comparator R Q S C10 PWM Logic 5.0mS +/-50uA (linear range) S2 0.10000 5V Nonlinear Gain Input From Voltage Loop Fault 0.01000 0.00100 Figure 8 Complete System Current Loop 0.00010 3.6.2 Current Loop Compensation The compensation of the current loop is implemented at the ICOMP pin. This is OTA6 output and a capacitor CICOMP has to be installed at this node to ground (see Figure 8). Under normal mode of the operation, this pin gives a voltage which is proportional to the averaged inductor current. This pin is internally shorted to 5V in the event of standby mode. 0.00001 0 18 37 55 73 91 110 128 146 165 183 201 219 238 256 PI digital output Figure 7 3.6 Power Transfer Curve Average Current Control The choke current is sensed through the voltage across the shunt resistor and averaged by the ICOMP pin capacitor so that the IC can control the choke current to track the instant variation of the input voltage. 3.6.3 Pulse Width Modulation (PWM) The IC employs an average current control scheme in continuous mode (CCM) to achieve the power factor correction. Assuming the voltage loop is working and output voltage is kept constant, the off duty cycle DOFF for a CCM PFC system is given as: 3.6.1 Complete Current Loop The complete system current loop is shown in Figure 8. It consists of the current loop block which averages the voltage at ISENSE pin resulted from the inductor current flowing across Rshunt. The averaged waveform is compared with an internal ramp in the ramp generator and PWM block. Once the ramp crosses the average waveform, the comparator C10 turns on the driver stage through the PWM logic block. The Nonlinear Gain block defines the amplitude of the inductor current. The following sections describe the functionality of each individual blocks. Version 3.0 DOFF=VIN/VOUT From the above equation, DOFF is proportional to VIN. The objective of the current loop is to regulate the average inductor current such that it is proportional to the off duty cycle DOFF, and thus to the input voltage VIN. Figure 9 shows the scheme to achieve the objective. 8 03 April 2017 CCM-PFC ICE3PCS03G Functional Description Ramp Profile immediately and maintained in off state for the current PWM cycle. The signal TOFFMIN resets (highest priority, overriding other input signals) both the current limit latch and the PWM on latch as illustrated in Figure 11. Ave(Iin) at ICOMP Current limit Latch R Q Toff _min 600ns Peak current limit Gate Drive t Figure 9 Current loop PWM on signal Average Current Control in CCM The PWM is performed by the intersection of a ramp signal with the averaged inductor current at pin 3 (ICOMP). The PWM cycles starts with the Gate turn off for a duration of TOFFMIN (600ns typ.) and the ramp is kept discharged. The ramp is allowed to rise after the TOFFMIN expires. The off time of the boost transistor ends at the intersection of the ramp signal and the averaged current waveform. This results in the proportional relationship between the average current and the off duty cycle DOFF. Figure 10 shows the timing diagrams of the TOFFMIN and the gate waveforms. Figure 11 3.8 S Q PWM LOGIC System Protection 3.8.1 Input Voltage Brownout Protection(BOP) Brownout occurs when the input voltage VIN falls below the minimum input voltage of the design (i.e. 85V for universal input voltage range) and the VCC has not entered into the VCCUVLO level yet. For a system without BOP, the boost converter will increasingly draw a higher current from the mains at a given output power which may exceed the maximum design values of the input current. ICE3PCS03G provides a new BOP feature whereby it senses directly the input voltage for Input Brown-Out condition via an external resistor/capacitor/diode network shown in Figure 12. This network provides a filtered value of VIN which turns the IC on when the voltage at pin 5 (BOP) is more than 1.25V. The IC enters into the fault mode when BOP goes below 1.0V. The hysteresis prevents the system to oscillate between normal and fault mode. Note also that the peak of VIN needs to be at least 20% of the rated VOUT in order to overcome OLP and powerup system. Toff _min 600 ns PWM Cycle VC,ref (1) Vram p Ramp Released GATE t (1) V c,ref is a function of V ICOMP 3.7 PWM on Latch R Q The IC provides numerous protection features in order to ensure the PFC system in safe operation. Clock Figure 10 High = turn on Gate S Q Ramp and PWM waveforms PWM Logic The PWM logic block prioritizes the control input signal and generates the final logic signal to turn on the driver stage. The speed of the logic gates in this block, together with the width of the reset pulse TOFFMIN, are designed to meet a maximum duty cycle DMAX of 95% at the GATE output under 65kHz of operation. In case of high input currents which results in Peak Current Limitation, the GATE will be turned off Version 3.0 9 03 April 2017 CCM-PFC ICE3PCS03G Functional Description VSENSE pin with respect to a reference voltage of 2.7V. A VSENSE voltage higher than 2.7V will immediately turn off the gate, thereby preventing damage to bus capacitor. After bulk voltage falls below the rated value, gate drive resumes switching again. Line Filter 90 ~ 270 Vac D BRO2 D BRO1 3.9 R BRO1 1.25V C8b BOP R BRO2 Brownout Latch R Q Brownout S Q C BRO R BRO3 C8a 1V Figure 12 Output Gate Driver The output gate driver is a fast totem pole gate drive. It has an in-built cross conduction currents protection and a Zener diode Z1 (see Figure 14) to protect the external transistor switch against undesirable over voltages. The maximum voltage at pin 8 (GATE) is typically clamped at 15V. The output is active HIGH and at VCC voltages below the under voltage lockout threshold VCCUVLO, the gate drive is internally pull low to maintain the off state. Input Brownout Protection 3.8.2 Peak Current Limit (PCL) The IC provides a cycle by cycle peak current limitation (PCL). It is active when the voltage at pin 1 (ISENSE) reaches -0.4V. This voltage is amplified by a factor of 2.5 and connected to comparator with a reference voltage of 1.0V as shown in Figure 13. A deglitcher with 200ns after the comparator improves noise immunity to the activation of this protection. VCC Reg (17V) PWM Logic HIGH to turn on Gate Driver LV Z1 External MOS GATE Full-wave rectifier * LV: Level Shift ISENSE R CS G=-2.5 Figure 14 Gate Driver 200ns AO2 Rshunt C5 Iin PCL 1V SGND Figure 13 Peak Current Limit (PCL) 3.8.3 Open Loop Protection (OLP) Whenever VSENSE voltage falls below 0.5V, or equivalently VOUT falls below 20% of its rated value, it indicates an open loop condition (i.e. VSENSE pin not connected) or an insufficient input voltage VIN for normal operation. It is implemented using comparator C2a with a threshold of 0.5V as shown in the IC block diagram in Figure 6. 3.8.4 First Over-Voltage Protection (OVP) Whenever VOUT exceeds the rated value by 8%, the over-voltage protection OVP1 is active as shown in Figure 6. This is implemented by sensing the voltage at Version 3.0 10 03 April 2017 CCM-PFC ICE3PCS03G Functional Description 3.10 Protection Function Description of Fault Fault-Type Min. Duration of Effect Consequence Voltage at Pin ISENSE < -400mV PCL 200 ns Gate Driver is turned off immediately during current switching cycle Voltage at Pin BOP < 1V BOP 20 s Gate Driver is turned off. Soft-restart after BOP voltage > 1.25V Voltage at Pin VSENSE < 0.5V OLP 1 s Power down. Soft-restart after VSENSE voltage > 0.5V Voltage at Pin VSENSE > 108% of rated level 12 s Gate Driver is turned off until VSENSE voltage < 2.5V. Version 3.0 OVP1 11 03 April 2017 CCM-PFC ICE3PCS03G Electrical Characteristics 4 Electrical Characteristics All voltages are measured with respect to ground (pin 2). The voltage levels are valid if other ratings are not violated. 4.1 Absolute Maximum Ratings Absolute maximum ratings are defined as ratings, which when being exceeded may lead to destruction of the integrated circuit. For the same reason make sure, that any capacitor that will be connected to pin 7 (VCC) is discharged before assembling the application circuit. Parameter Symbol Values Min. Typ. Unit Note / Test Condition Max. VCC Supply Voltage VVCC -0.3 26 V GATE Voltage VGATE -0.3 17 V Clamped at 15V if driven internally. ISENSE Voltage VISENSE -20 5.3 V 1) mA ISENSE Current IISENSE -1 1 VSENSE Voltage VVSENSE -0.3 5.3 V VSENSE Current IVSENSE -1 1 mA ICOMP Voltage VICOMP -0.3 5.3 V FREQ Voltage VFREQ -0.3 5.3 V BOP Voltage VBOP -0.3 9.5 V 2) BOP Current IBOP -1 35 A Junction Temperature TJ -40 150 C Storage Temperature TA,STO -55 150 Thermal Resistance RTHJA 185 Soldering Temperature TSLD 260 C Wave Soldering3) ESD Capability VESD 2 kV Human Body Model4) 1) 2) 3) 4) C K/W Junction to Air Absolute ISENSE current should not be exceeded Absolute BOP current should not be exceeded According to JESD22A111 According to EIA/JESD22-A114-B (discharging an 100 pF capacitor through an 1.5k series resistor) Version 3.0 12 03 April 2017 CCM-PFC ICE3PCS03G Electrical Characteristics 4.2 Note: Operating Range Within the operating range the IC operates as described in the functional description. Parameter Symbol Values Min. Unit Typ. VCC Supply Voltage @ 25C VVCC VVCC,OFF 25 V Junction Temperature TJ -25 125 C PFC switching frequency FPFC 21 100 kHz 4.3 Note: 4.3.1 Note / Test Condition Max. TJ=25C Characteristics The electrical Characteristics involve the spread of values given within the specified supply voltage and junction temperature range TJ from -25 C to 125 C. Typical values represent the median values, which are related to 25 C. If not otherwise stated, a supply voltage of VVCC = 18V, a typical switching frequency of ffreq=65kHz are assumed and the IC operates in active mode. Furthermore, all voltages are referring to GND if not otherwise mentioned. Supply Section Parameter Symbol Limit Values Min. Unit Note/Test Condition Typ. Max. VCC Turn-On Threshold VCCon 11.5 12 12.9 V VCC Turn-Off Threshold/ Under Voltage Lock Out VCCUVLO 10.5 11.0 11.9 V VCC Turn-On/Off Hysteresis VCChy 0.7 1 1.45 V Start Up Current Before VCCon ICCstart1 - 380 680 A VCCon-1.2V Start Up Current Before VCCon ICCstart2 - 1.4 2.4 mA VCCon-0.2V Operating Current with active GATE ICCHG - 6.4 8.5 mA CL= 1nF Operating Current during Standby ICCStdby - 3.5 4.7 mA VVSENSE= 0.4V VICOMP= 4V Version 3.0 13 03 April 2017 CCM-PFC ICE3PCS03G Electrical Characteristics 4.3.2 Variable Frequency Section Parameter Symbol Limit Values Min. Unit Test Condition Typ. Max. Switching Frequency (Typical) FSWnom 62.5 65 67.5 kHz R5 = 67k Switching Frequency (Min.) FSWmin - 21 - kHz R5 = 212k Switching Frequency (Max.) FSWmax - 100 - kHz R5 = 43k Voltage at FREQ pin VFREQ - 1 - V Max. Duty Cycle Dmax 93 95 98.5 % 4.3.3 PWM Section Parameter Symbol Limit Values Min. Min. Duty Cycle DMIN Min. Off Time TOFFMIN 4.3.4 fSW=fSWnom (RFREQ=67k) 310 Typ. 600 Unit Test Condition Max. 0 % VVSENSE= 2.5V VICOMP= 4.3V 920 ns VVSENSE= 2.5V VISENSE= 0V (R5 = 67k) External Synchronization Parameter Symbol Values Min. Detection threshold of external clock Vthr_EXT Synchronization range fEXT_range Synchronization frequency ratio fEXT:fPFC propagation delay from rising edge of external clock to falling edge of PFC gate drive TEXT2GATE Allowable external duty on time TD_on Version 3.0 Typ. Unit 2.5 50 Note / Test Condition Max. V 100 kHz 500 ns 70 % 1:1 10 14 fEXT=65kHz 03 April 2017 CCM-PFC ICE3PCS03G Electrical Characteristics 4.3.5 PFC Brownout Protection Section Parameter Symbol Values Unit Min. Typ. Max. Input Brownout Protection High to Low Threshold VBOP_H2L 0.98 1 1.02 V Input Brownout Protection Low to High Threshold VBOP_L2H 1.2 1.25 1.3 V 0.5 A Blanking time for BOP turn_on TBOPon Input Brownout Protection BOP Bias Current IBOP 4.3.6 s 20 -0.5 - Symbol Values Unit Note / Test Condition Min. Typ. Max. Over Voltage Protection (OVP) Low to High VOVP1_L2H 2.65 2.7 2.77 V Over Voltage Protection (OVP) High to Low VOVP1_H2L 2.45 2.5 2.55 V Over Voltage Protection (OVP ) Hysteresis VOVP1_HYS 150 200 270 mV -365 -400 -435 mV Blanking time for OVP TOVP1 Peak Current Limitation (PCL) ISENSE Threshold VPCL Blanking time for PCL turn_on TPCLon 108%VBULKRated s 12 200 ns Current Loop Section Parameter Symbol Values Min. OTA6 Transconductance Gain GmOTA6 OTA6 Output Linear Range1) IOTA6 ICOMP Voltage during OLP VICOMPF 1) VBOP=1.25V System Protection Section Parameter 4.3.7 Note / Test Condition 3.5 Unit Note / Test Condition Typ. Max . 5.0 6.35 4.8 5.0 mS At Temp = 25C A 50 5.2 V VVSENSE= 0.4V The parameter is not subject to production test - verified by design/characterization Version 3.0 15 03 April 2017 CCM-PFC ICE3PCS03G Electrical Characteristics 4.3.8 Voltage Loop Section Parameter Symbol Values Min. Typ. Unit Note / Test Condition Max . Trimmed Reference Voltage VVSREF 2.47 2.5 2.53 V Open Loop Protection (OLP) VSENSE Threshold VVS_OLP 0.45 0.5 0.55 V VSENSE Input Bias Current IVSENSE -1 - 1 A 4.3.9 VVSENSE= 2.5V Driver Section Parameter GATE Low Voltage GATE High Voltage 4.3.10 1.2% Symbol Values Unit Note / Test Condition Min. Typ. Max. - - 1.2 V VCC =10V IGATE = 5 mA - 0.4 - V IGATE = 0 A - - 1.4 V IGATE = 20 mA -0.2 0.8 - V IGATE = -20 mA - 15 - V VCC = 25V CL = 1nF - 12.4 - V VCC = 15V CL = 1nF 8.0 - - V VCC = VVCCoff + 0.2V CL = 1nF VGATEL VGATEH Gate Drive Section Parameter Symbol Values Unit Note / Test Condition Min. Typ. Max. GATE Rise Time tr - 30 - ns VGate = 20% - 80% VGATEH CL = 1nF GATE Fall Time tf - 25 - ns VGate = 80% - 20% VGATEH CL = 1nF Version 3.0 16 03 April 2017 CCM-PFC ICE3PCS03G Outline Dimension 5 Outline Dimension PG-DSO-8 Outline Dimension 1.27 0.1 0.41 +0.1 -0.05 .01 0.2 +0.05 -0 C 0.2 M A C x8 8 5 Index Marking 1 4 5 -0.21) 8 MAX. 4 -0.21) 1.75 MAX. 0.1 MIN. (1.5) 0.33 0.08 x 45 0.64 0.25 6 0.2 A Index Marking (Chamfer) 1) Does not include plastic or metal protrusion of 0.15 max. per side Notes: 1. You can find all of our packages, sorts of packing and others in our Infineon Internet Page "Products": http://www.infineon.com/products. 2. Dimensions in mm. Version 3.0 17 03 April 2017 CCM-PFC Revision History: Page 3/6/13/ 14 Maximum switching frequency was changed to 100kHz Figure 4 Maximum switching frequency was changed to 100kHz Page 14 Maximum synchronization frequency was changed to 100kHz Datasheet Edition 2017-04-03 Published by Infineon Technologies AG 81726 Munich, Germany (c)Infineon Technologies AG 05/05/10. All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.