REVISIONS
LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
A
Made technical changes to table I.
91-10-08
K. A. Cottongim
B
Changes in accordance with NOR 5962-R048-94
93-11-29
K. A. Cottongim
C
Table I, Stability/noise test, conditions column, change CL from
680 pF to 330 pF. Add RL = 100 Ω.
00-08-01
Raymond Monnin
D
Updated drawing to reflect the current requirements of MIL-PRF-
38534. -sld
03-06-03
Raymond Monnin
E
Added footnote 1 to table II, under group C end-point electricals.
Updated drawing paragraphs. -sld
11-12-12
Charles F. Saffle
THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV
E
E
E
E
E
E
E
E
E
E
SHEET
1
2
3
4
5
6
7
8
9
10
PMIC N/A PREPARED BY
Steve Duncan DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil/
MICROCIRCUIT
DRAWING
CHECKED BY
Gary Zahn
THIS DRAWING IS
AVAILABLE
FOR USE BY ALL
DEPARTMENTS
APPROVED BY
Kendall A. Cottongim
MICROCIRCUIT, HYBRID, LI NEAR, HIGH
POWER, OPERATIONAL AMPLIFIER
DEPARTMENT OF DEFENSE
DRAWING APPROVAL DATE
91-03-29
REVISION LEVEL
E SIZE
A CAGE CODE
67268
5962-90828
SHEET
1 OF
10
DSCC FORM 2233
APR 97 5962-E044-12
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-90828
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
E
SHEET
2
DSCC FORM 2234
APR 97
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
available, a choice of radiation hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962 - 90828 01 H X X
Federal RHA Device Device Case Lead
stock class designator type class outline finish
designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5)
\ / (see 1.2.3)
\/
Drawing number
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specif ied RH A
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Dev ice ty pe(s). The device type(s) identify the circ uit function as follows:
Device type Generic number Circuit function
01 PA10M, MIOP42115 Power operational amplifier
1.2.3 Dev ice cl as s designator. This device class designator shall be a single letter identifying the product assurance level.
All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,
and E) or QML Listing (Class G and D). The product assurance levels are as follows:
Devi ce class Device performance documentation
K Highest reliability class available. This level is intended for use in space
applications.
H Standard military qual ity class level. This level is intended for use in applications
where non-space high reliability devices are required.
G Reduced testing version of the s tandard military quality class. This level uses the
Class H screening and In-Process Inspections with a possible limited temperature
range, manufacturer specified inc oming flow, and the manufacturer guarantees (but
may not test) periodic and conformance inspections (Group A, B, C and D).
E Designates devices which are based upon one of the other classes (K, H, or G)
with exception(s) taken to the requirements of that class. These exception(s) must
be specified in the devi ce acquisition document; therefore the acquisition document
should be revi ewed to ensure that the exception(s) taken will not adversely affect
system performance.
D Manufacturer specified quality class. Quality level is defined by the manufac turers
internal, QML certified flow. This product may have a limited temperature range.
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter Descriptive designator Terminals Package style
X See figure 1 8 Flange mount
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-90828
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
E
SHEET
3
DSCC FORM 2234
APR 97
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absol ute maximum ratings. 1/
Supply voltage (VS) ..................................................................... ±50 V dc
Output current (IO) ....................................................................... 5.0 A
Power dissipation(PD) 2/ ............................................................. 67 W
Input voltage (differential) ........................................................... ±50 V dc - 3 V dc
Input voltage (common mode) .................................................... ±50 V dc
Lead temperature (soldering, 10 seconds) ................................. +300°C
Junction temperature (TJ) ........................................................... +200°C
Storage temperature range ......................................................... -65°C to +150°C
1.4 Recom mended operati ng cond itio ns.
Supply voltage (VS) ..................................................................... ±40 V dc
Case operating temperature range (TC) ...................................... -55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Governm ent specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitati on or contr ac t.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard M icrocircu it Drawings.
(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadel phia, PA 19111-5094.)
2.2 Order of prece den ce. In the event of a conflict between the text of this drawi ng and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
2/ Derate at 2.6°C/W above case temperature (TC) of +25°C.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-90828
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
E
SHEET
4
DSCC FORM 2234
APR 97
3. REQUIREMENTS
3.1 Item requirements. The individual i tem performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable devi ce class. The
manufactur er may el im inat e, modify or optimize the tests and inspections herein, however the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modi fication in the QM plan shall not
affect the form, fit, or function of the device for the applic abl e device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38534 and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.3 Electr ica l performance characterist ic s. Unless otherwise specified herein, the el ectrical performance characteristics are
as specified in table I and shall appl y over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Mar king of dev ice( s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the dev ice described
herein shall m aintain the elec trical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type lis ted herein. Al s o, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DLA Land and Maritime -VA) upon request.
3.7 Certif i cate of compli an ce. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy ) sub mi tted to DLA Land and Maritime -VA s h all affirm that the
manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein.
3.8 Certif i cate of conform anc e. A certificate of c onformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircu its del iv ered t o this draw ing.
4. VERIFICATION
4.1 Sampling and i nspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quali ty Management (Q M) plan. The modification in the QM plan shall not affect the form,
fit, or function as described herein.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition D. The test circuit shall be maintained by the manufacturer under document revision level control and
shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test
circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent
specified in test method 1015 of MIL-STD-883.
(2) TA as specified in accordance with table I of method 1015 of MIL-STD-883.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-90828
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
E
SHEET
5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/
-55°C ≤ TC ≤ +125°C
VS = ±40 V dc
unless otherw ise speci fied
Group A
subgroups
Device
type
Limits
Unit
Min
Max
Supply current
ICL
VIN = 0 V dc, G = 100, 2/
±RCL = 1.0 Ω, VCM = 0 V dc
1,2
01
30
mA
3
75
Input offset volt age
VOS
VIN = 0 V dc, G = 100, 2/
VS = ±10 V dc , ±RCL = 1.0 Ω
1
01
-12.0
+12.0
mV
2
-18.5
+18.5
3
-17.2
+17.2
VIN = 0 V dc, G = 100, 2/
VS = ±40 V dc , ±RCL = 1.0 Ω
1
-6.0
+6.0
mV
2
-12.5
+12.5
3
-11.2
+11.2
VIN = 0 V dc, G = 100, 2/
VS = ±45 V dc , ±RCL = 1.0 Ω
1
-7.0
+7.0
mV
2
-13.5
+13.5
3
-12.2
+12.2
Input bias current, +IN
+IB
VIN = 0 V dc, RBIAS ≤ 100 MΩ
1
01
30.0
nA
2
70.0
3
115.0
Input bias current , -IN
-IB
VIN = 0 V dc, RBIAS ≤ 100 MΩ
1
01
30.0
nA
2
70.0
3
115.0
Input offset current
IOS
VIN = 0 V dc, RBIAS ≤ 100 MΩ
1
01
30.0
nA
2
70.0
3
115.0
Output voltage
VO
VS = ±45 V dc, IO = 80 mA,
RL = 500
Ω
4,5,6
01
40
V
VS = ±30 V dc, IO = 2 A,
RL = 12 Ω
4,5,6
24
V
VS = ±18 V dc, IO = 5 A,
RL = 2.07 Ω, TC = +25°C, -55°C
4,6
10
V
VS = ±14.3 V dc, IO = 3 A,
RL = 2.07
Ω,
TC = +125
°
C
5
6.3
V
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-90828
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
E
SHEET
6
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/
-55°C ≤ TC ≤ +125°C
VS =
±
40 V dc
Group A
subgroups
Device
type
Limits
Unit
unless otherw ise speci fied
Min
Max
Current limits
IS
RL = 12.0Ω, ±RCL = 1.0Ω, 2/
VS = ±17 V dc, TC = +25°C
4
01
0.6
0.89
A
Stability/noise
EN
G = 1, CL = 330 pF, RL = 100 Ω
4,5,6
01
1.0
mV
Slew rate
SR
RL = 500Ω, VIN ≥ 4 VP-P
4,5,6
01
2.0
10.0
V/µs
Open loop gain
AOL
RL = 500Ω, f = 15 Hz,
VIN
≥
0.4 VP-P
4,5,6
01
96
dB
Common mode
rejection
CMR
VS = ±15 V dc, f = dc,
VCM = ±9 V dc
4,5,6
01
74
dB
1/ During all group A testing, terminal connection F. O. (pin 7) is left open.
2/ A current limiting resistor (RCL) is connected between CL+ to the output and CL- to the output during these tests.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-90828
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
E
SHEET
7
DSCC FORM 2234
APR 97
Case outline X.
Symbol
Millimeters
Inches
Min
Max
Min
Max
A
38.35
39.37
1.510
1.550
B
19.30
19.81
.760
.780
C
7.37
.290
D
0.97
1.07
.038
.042
E
2.03
2.54
.080
.100
F
40° BSC
40° BSC
G
12.7 BSC
.500 BSC
H
30.12 BSC
1.186 BSC
J
15.06 BSC
.593 BSC
K
11.68
12.70
.460
.500
Q
3.84
4.09
.151
.161
R
25.15
25.65
.990
1.010
NOTES:
1. The U. S. preferred system of measurement is the metric SI. This case outline was originally designed using inch-
pound units of measurement, in the event of c onflict between the metric and inch-pound units, the inch-pound shall take
precedence.
2. Pin numbers are for reference and may not be marked on package.
FIGURE 1. Case outline(s).
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-90828
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
E
SHEET
8
DSCC FORM 2234
APR 97
Device type
01
Case outline
X
Terminal number
Terminal symbo l
1
2
3
4
5
6
7
8
Output
+Current limit (CL+)
+VS
+IN
-IN
-VS
F. O.
-Current limit (CL-)
FIGURE 2. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-90828
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
E
SHEET
9
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-PRF-38534 test requirements
Subgroups
(in accordance with
MIL-PRF-38534, group A
test table)
Interim electrical parameters
Final electrical parameters
1*, 2, 3, 4, 5, 6
Group A test requirements
1, 2, 3, 4, 5, 6
Group C end-point electrical 1/
parameters
1, 2, 3, 4
End-
point electrical parameters
for radiation hardness assurance
(RHA) devices
Not applicable
1/ As a minimum, for all Group C testing performed after (11-12-12)
manufacturers shall perform subgroups 1, 2, and 3 from the Group A
electrical test table (Table C-Xa of MIL-PRF-38534).
* PDA applies to subgroup 1.
4.3 Conformance and periodic i nspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance
with MIL-PRF-38534 and as specified herein.
4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follow s:
a. Tests shall be as specified in table II herein.
b. Subgroups 7, 8, 9, 10, and 11 shall be omitted.
4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534.
4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows:
a. End-point elect ric al para meters shall be as specified in table I I herein.
b. Steady-state life test, method 1005 of MIL-STD-883.
(1) Test condition D. The test circuit shall be maintained by the manufacturer under document revision level control and
shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test
circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent
specified in test method 1005 of MIL-STD-883.
(2) TA as specified in accordance with table I of method 1015 of MIL-STD-883.
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534.
4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection i s not currently applicable to this drawing.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-90828
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
E
SHEET
10
DSCC FORM 2234
APR 97
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534.
6. NOTES
6.1 Intended us e. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logisti cs purpo ses.
6.2 Replaceability. Microcirc ui ts covered by this drawing will replace the same generic device covered by a contrac tor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF-
38534.
6.4 Record of user s. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list
will be used for coordi nation and distribution of changes to the drawings . Users of drawings covering microelectronic devices
(FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-0547.
6.5 Comments. Com ments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 432 18-3990,
or telephone (614) 692-1081.
6.6 Sources of s upply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors l isted in MIL-HDBK-103
and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime-VA and hav e agr e ed to
this drawing.
STANDARD MICROCIRCUIT DRAWING BULL E TIN
DATE: 11-12-12
Approved sour ces of supply for SMD 5962-90828 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be
revised to inc lude the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information
bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9082801HXA
5962-9082801HXC
31757
31757
MIOP42115/883
MIOP42115/883
5962-9082801HXA
5962-9082801HXC
60024
60024
PA10M/883
PA10M/883
1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the
manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine its
availability.
2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the
performance requirements of this drawing.
Vendor CAGE Vendor name
number and address
31757 Mi c ropac Industries, Incorporated
905 East Walnut Street
Garland, TX 75040
60024 Cirrus Logic Incorporated.
DBA Apex Microtechnology
5980 North Shannon Road
Tucson, AZ 85741
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.